| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
mlx4 devices (ConnectX-2, ConnectX-3) has a limitation
where rdma read work queue entries cannot exceed 512 bytes.
A rdma_read wqe needs to fit in 512 bytes:
- wqe control segment (16 bytes)
- rdma segment (16 bytes)
- scatter elements (16 bytes each)
So max_sge_rd should be: (512 - 16 - 16) / 16 = 30.
Signed-off-by: Sagi Grimberg <[email protected]>
Reviewed-by: Steve Wise <[email protected]>
Signed-off-by: Doug Ledford <[email protected]>
|
|
Receipt of CM MAD with other than the Send method for an attribute
other than the ClassPortInfo attribute is invalid.
CM attributes other than ClassPortInfo only use the send method.
The SRP initiator does not maintain a timeout policy for CM connect
requests relies on the CM layer to do that. The result was that
the SRP initiator hung as the connect request never completed.
A new SRP target has been observed to respond to Send CM REQ
with GetResp of CM REQ with bad status. This is non conformant
with IBA spec but exposes a vulnerability in the current MAD/CM
code which will respond to the incoming GetResp of CM REQ as if
it was a valid incoming Send of CM REQ rather than tossing
this on the floor. It also causes the MAD layer not to
retransmit the original REQ even though it has not received a REP.
Reviewed-by: Sagi Grimberg <[email protected]>
Signed-off-by: Hal Rosenstock <[email protected]>
Reviewed-by: Ira Weiny <[email protected]>
Signed-off-by: Doug Ledford <[email protected]>
|
|
Ensure that validate_ipv4_net_dev() calls rcu_read_unlock() if
fib_lookup() fails. Detected by sparse. Compile-tested only.
Fixes: "IB/cma: Validate routing of incoming requests" (commit f887f2ac87c2).
Cc: Haggai Eran <[email protected]>
Cc: stable <[email protected]>
Reviewed-by: Sagi Grimberg <[email protected]>
Reviewed-by: Haggai Eran <[email protected]>
Reviewed-by: Jason Gunthorpe <[email protected]>
Signed-off-by: Doug Ledford <[email protected]>
|
|
__unflatten_device_tree() calls unflatten_dt_node(), which declares
a static variable. It is therefore not reentrant.
One of the callers of __unflatten_device_tree(), unflatten_device_tree(),
is only called once during early initialization and does not need to be
protected. The other caller, of_fdt_unflatten_tree(), can be called at
any time, possibly multiple times in parallel. This can happen, for
example, if multiple devicetree overlays have to be loaded and installed.
Without this protection, errors such as the following may be seen.
kernel: End of tree marker overwritten: e6a3a458
kernel: find_target_node:
Failed to find target-indirect node at /fragment@0
kernel: __of_overlay_create: of_build_overlay_info() failed for tree@/
Add a mutex to of_fdt_unflatten_tree() to make the call reentrant.
Cc: Pantelis Antoniou <[email protected]>
Signed-off-by: Guenter Roeck <[email protected]>
Cc: [email protected] # v4.1+
Signed-off-by: Rob Herring <[email protected]>
|
|
Fixes native drm clients like Fedora 23 Wayland which now appears to
be able to use cursor hotspots without strange cursor offsets.
Also fixes a couple of ignored error paths.
Since the core drm cursor hotspot is incompatible with the legacy vmwgfx
hotspot (the core drm hotspot is reset when the drm_mode_cursor ioctl
is used), we need to keep track of both and add them when the device
hotspot is set. We assume that either is always zero.
Signed-off-by: Thomas Hellstrom <[email protected]>
Reviewed-by: Sinclair Yeh <[email protected]>
|
|
We have two latest thinkpad laptop models which are all based on the
Intel skylake platforms, and all of them have the codec alc293 on
them. When the machines boot to the desktop, an greeting dialogue
shows up with the notification sound. But on these two models, there
is noise with the notification sound. We have 3 SKUs for each of
the models, all of them have this problem.
So far, this problem is only specific to these two thinkpad models,
we did not find this problem on the old thinkpad models with the
codec alc293 or alc292.
A workaround for this problem is disabling the aamix.
Cc: [email protected]
BugLink: https://bugs.launchpad.net/bugs/1523517
Signed-off-by: Hui Wang <[email protected]>
Signed-off-by: Takashi Iwai <[email protected]>
|
|
On 12/03/2015 01:18 AM, Christoph Hellwig wrote:
> The patch looks good to me, but while we touch this area, how about
> throwing in a few cosmetic fixes as well?
How about the patch below ? In that version of the ib_sg_to_pages() fix
these concerns have been addressed and additionally to more bugs have been fixed.
------------
[PATCH] IB core: Fix ib_sg_to_pages()
Fix the code for detecting gaps. A gap occurs not only if the
second or later scatterlist element is not aligned but also if
any scatterlist element other than the last does not end at a
page boundary.
In the code for coalescing contiguous elements, ensure that
mr->length is correct and that last_page_addr is up-to-date.
Ensure that this function returns a negative
error code instead of zero if the first set_page() call fails.
Fixes: commit 4c67e2bfc8b7 ("IB/core: Introduce new fast registration API")
Reported-by: Christoph Hellwig <[email protected]>
Reviewed-by: Sagi Grimberg <[email protected]>
Reviewed-by: Christoph Hellwig <[email protected]>
Signed-off-by: Doug Ledford <[email protected]>
|
|
After dma_map_sg() has been called the return value of that function
must be used as the number of elements in the scatterlist instead of
scsi_sg_count().
Fixes: commit f7f7aab1a5c0 ("IB/srp: Convert to new registration API")
Reported-by: Christoph Hellwig <[email protected]>
Signed-off-by: Bart Van Assche <[email protected]>
Cc: stable <[email protected]> # v4.4+
Cc: Sagi Grimberg <[email protected]>
Cc: Sebastian Parschauer <[email protected]>
Reviewed-by: Sagi Grimberg <[email protected]>
Signed-off-by: Doug Ledford <[email protected]>
|
|
Detected by sparse.
Fixes: commit 330179f2fa93 ("IB/srp: Register the indirect data buffer descriptor")
Signed-off-by: Bart Van Assche <[email protected]>
Cc: stable <[email protected]> # v4.3+
Cc: Sagi Grimberg <[email protected]>
Cc: Christoph Hellwig <[email protected]>
Cc: Sebastian Parschauer <[email protected]>
Reviewed-by: Christoph Hellwig <[email protected]>
Signed-off-by: Doug Ledford <[email protected]>
|
|
Without this sg_dma_len will return 0 on architectures tha have
the dma_length field.
Fixes: commit f7f7aab1a5c0 ("IB/srp: Convert to new registration API")
Signed-off-by: Christoph Hellwig <[email protected]>
Reviewed-by: Sagi Grimberg <[email protected]>
Signed-off-by: Doug Ledford <[email protected]>
|
|
When using work request based memory registration (fast_reg)
we must reserve SQ entries for registration and invalidation
in addition to send operations. Each IO consumes 3 SQ entries
(registration, send, invalidation) so we need to allocate 3x
larger send-queue instead of 2x.
Signed-off-by: Sagi Grimberg <[email protected]>
CC: Stable <[email protected]>
Reviewed-by: Christoph Hellwig <[email protected]>
Signed-off-by: Doug Ledford <[email protected]>
|
|
If srp_connect_ch() returns a positive value then that is considered
by its caller as a connection failure but this does not result in a
scsi_host_put() call and additionally causes the srp_create_target()
function to return a positive value while it should return a negative
value. Avoid all this confusion and additionally fix a memory leak by
ensuring that srp_connect_ch() always returns a value that is <= 0.
This patch avoids that a rejected login triggers the following memory
leak:
unreferenced object 0xffff88021b24a220 (size 8):
comm "srp_daemon", pid 56421, jiffies 4295006762 (age 4240.750s)
hex dump (first 8 bytes):
68 6f 73 74 35 38 00 a5 host58..
backtrace:
[<ffffffff8151014a>] kmemleak_alloc+0x7a/0xc0
[<ffffffff81165c1e>] __kmalloc_track_caller+0xfe/0x160
[<ffffffff81260d2b>] kvasprintf+0x5b/0x90
[<ffffffff81260e2d>] kvasprintf_const+0x8d/0xb0
[<ffffffff81254b0c>] kobject_set_name_vargs+0x3c/0xa0
[<ffffffff81337e3c>] dev_set_name+0x3c/0x40
[<ffffffff81355757>] scsi_host_alloc+0x327/0x4b0
[<ffffffffa03edc8e>] srp_create_target+0x4e/0x8a0 [ib_srp]
[<ffffffff8133778b>] dev_attr_store+0x1b/0x20
[<ffffffff811f27fa>] sysfs_kf_write+0x4a/0x60
[<ffffffff811f1e8e>] kernfs_fop_write+0x14e/0x180
[<ffffffff81176eef>] __vfs_write+0x2f/0xf0
[<ffffffff811771e4>] vfs_write+0xa4/0x100
[<ffffffff81177c64>] SyS_write+0x54/0xc0
[<ffffffff8151b257>] entry_SYSCALL_64_fastpath+0x12/0x6f
Signed-off-by: Bart Van Assche <[email protected]>
Reviewed-by: Christoph Hellwig <[email protected]>
Reviewed-by: Sagi Grimberg <[email protected]>
Cc: Sebastian Parschauer <[email protected]>
Cc: stable <[email protected]>
Signed-off-by: Doug Ledford <[email protected]>
|
|
It was found by Saurabh Sengar that the netlink code tried to allocate
memory with GFP_KERNEL while holding a spinlock. While it is possible
to fix the issue by replacing GFP_KERNEL with GFP_ATOMIC, it is better
to get rid of the spinlock while sending the packet. However, in order
to protect against a race condition that a quick response may be received
before the request is put on the request list, we need to put the request
on the list first.
Signed-off-by: Kaike Wan <[email protected]>
Reviewed-by: Jason Gunthorpe <[email protected]>
Reviewed-by: Ira Weiny <[email protected]>
Reported-by: Saurabh Sengar <[email protected]>
Signed-off-by: Doug Ledford <[email protected]>
|
|
do_div is the wrong way to divide a sector_t, as it is less
efficient when sector_t is 32-bit wide. With the upcoming
do_div optimizations, the kernel starts warning about this:
drivers/infiniband/ulp/iser/iser_verbs.c:1296:4: note: in expansion of macro 'do_div'
include/asm-generic/div64.h:224:22: warning: passing argument 1 of '__div64_32' from incompatible pointer type
This changes the code to use sector_div instead, which always
produces optimal code.
Signed-off-by: Arnd Bergmann <[email protected]>
Reviewed-by: Sagi Grimberg <[email protected]>
Signed-off-by: Doug Ledford <[email protected]>
|
|
The current implementation gets a spin_lock, and at any scale with
qib and hfi1 post send, the lock contention grows exponentially
with the number of QPs.
idr_find() is RCU compatibile, so read doesn't need the lock.
Change to use rcu_read_lock() and rcu_read_unlock() in
__idr_get_uobj().
kfree_rcu() is used to insure a grace period between the
idr removal and actual free.
Reviewed-by: Ira Weiny <[email protected]>
Signed-off-by: Mike Marciniszyn <[email protected]>
Reviewed-By: Jason Gunthorpe <[email protected]>
Signed-off-by: Doug Ledford <[email protected]>
|
|
Minor errors found via code inspection during future development.
SFF 8636 defines bit position 2 to hold the status indication of
QSFP memory paging. The mask used to test for the value was
incorrect and is fixed in this patch. Additionally, the dump
function had a mismatch between the field being printed out and
the field used to source the data which was fixed.
Reviewed-by: Mitko Haralanov <[email protected]>
Reviewed-by: Mike Marciniszyn <[email protected]>
Reported-by: Easwar Hariharan <[email protected]>
Signed-off-by: Easwar Hariharan <[email protected]>
Signed-off-by: Mike Marciniszyn <[email protected]>
Signed-off-by: Doug Ledford <[email protected]>
|
|
Commit e622f2f4ad21 ("IB: split struct ib_send_wr")
introduced a regression for HCAs whose user mode post
sends go through ib_uverbs_post_send().
The code didn't account for the fact that the first sge is
offset by an operation dependent length. The allocation did,
but the pointer to the destination sge list is computed without
that knowledge. The sge list copy_from_user() then corrupts
fields in the work request
Store the operation dependent length in a local variable and
compute the sge list copy_from_user() destination using that length.
Reviewed-by: Ira Weiny <[email protected]>
Signed-off-by: Mike Marciniszyn <[email protected]>
Reviewed-by: Christoph Hellwig <[email protected]>
Signed-off-by: Doug Ledford <[email protected]>
|
|
struct qib_mr requires the mr member be the last because struct
qib_mregion contains a dynamic array at the end. The additions
of members should have been placed before this structure as the
comment noted.
Failure to do so was causing random memory corruption. Reproducing
this bug was easy to do by running the client and server of
ib_write_bw -s 8 -n 5 on the same node.
This BUG() was tripped in a slab debug kernel:
kernel BUG at mm/slab.c:2572!
Fixes: 38071a461f0a ("IB/qib: Support the new memory registration API")
Reviewed-by: Mike Marciniszyn <[email protected]>
Signed-off-by: Ira Weiny <[email protected]>
Signed-off-by: Doug Ledford <[email protected]>
|
|
Pull virtio fixes from Michael Tsirkin:
"This includes some fixes and cleanups in virtio and vhost code.
Most notably, shadowing the index fixes the excessive cacheline
bouncing observed on AMD platforms"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_ring: shadow available ring flags & index
virtio: Do not drop __GFP_HIGH in alloc_indirect
vhost: replace % with & on data path
tools/virtio: fix byteswap logic
tools/virtio: move list macro stubs
virtio: fix memory leak of virtio ida cache layers
vhost: relax log address alignment
virtio-net: Stop doing DMA from the stack
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"Ext4 bug fixes for v4.4, including fixes for post-2038 time encodings,
some endian conversion problems with ext4 encryption, potential memory
leaks after truncate in data=journal mode, and an ocfs2 regression
caused by a jbd2 performance improvement"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
jbd2: fix null committed data return in undo_access
ext4: add "static" to ext4_seq_##name##_fops struct
ext4: fix an endianness bug in ext4_encrypted_follow_link()
ext4: fix an endianness bug in ext4_encrypted_zeroout()
jbd2: Fix unreclaimed pages after truncate in data=journal mode
ext4: Fix handling of extended tv_sec
|
|
Improves cacheline transfer flow of available ring header.
Virtqueues are implemented as a pair of rings, one producer->consumer
avail ring and one consumer->producer used ring; preceding the
avail ring in memory are two contiguous u16 fields -- avail->flags
and avail->idx. A producer posts work by writing to avail->idx and
a consumer reads avail->idx.
The flags and idx fields only need to be written by a producer CPU
and only read by a consumer CPU; when the producer and consumer are
running on different CPUs and the virtio_ring code is structured to
only have source writes/sink reads, we can continuously transfer the
avail header cacheline between 'M' states between cores. This flow
optimizes core -> core bandwidth on certain CPUs.
(see: "Software Optimization Guide for AMD Family 15h Processors",
Section 11.6; similar language appears in the 10h guide and should
apply to CPUs w/ exclusive caches, using LLC as a transfer cache)
Unfortunately the existing virtio_ring code issued reads to the
avail->idx and read-modify-writes to avail->flags on the producer.
This change shadows the flags and index fields in producer memory;
the vring code now reads from the shadows and only ever writes to
avail->flags and avail->idx, allowing the cacheline to transfer
core -> core optimally.
In a concurrent version of vring_bench, the time required for
10,000,000 buffer checkout/returns was reduced by ~2% (average
across many runs) on an AMD Piledriver (15h) CPU:
(w/o shadowing):
Performance counter stats for './vring_bench':
5,451,082,016 L1-dcache-loads
...
2.221477739 seconds time elapsed
(w/ shadowing):
Performance counter stats for './vring_bench':
5,405,701,361 L1-dcache-loads
...
2.168405376 seconds time elapsed
The further away (in a NUMA sense) virtio producers and consumers are
from each other, the more we expect to benefit. Physical implementations
of virtio devices and implementations of virtio where the consumer polls
vring avail indexes (vhost) should also benefit.
Signed-off-by: Venkatesh Srinivas <[email protected]>
Signed-off-by: Michael S. Tsirkin <[email protected]>
|
|
b92b1b89a33c ("virtio: force vring descriptors to be allocated from
lowmem") tried to exclude highmem pages for descriptors so it cleared
__GFP_HIGHMEM from a given gfp mask. The patch also cleared __GFP_HIGH
which doesn't make much sense for this fix because __GFP_HIGH only
controls access to memory reserves and it doesn't have any influence
on the zone selection. Some of the call paths use GFP_ATOMIC and
dropping __GFP_HIGH will reduce their changes for success because the
lack of access to memory reserves.
Signed-off-by: Michal Hocko <[email protected]>
Signed-off-by: Michael S. Tsirkin <[email protected]>
Acked-by: Will Deacon <[email protected]>
Reviewed-by: Mel Gorman <[email protected]>
|
|
We know vring num is a power of 2, so use &
to mask the high bits.
Signed-off-by: Michael S. Tsirkin <[email protected]>
|
|
commit cf561f0d2eb74574ad9985a2feab134267a9d298 ("virtio: introduce
virtio_is_little_endian() helper") changed byteswap logic to
skip feature bit checks for LE platforms, but didn't
update tools/virtio, so vring_bench started failing.
Update the copy under tools/virtio/ (TODO: find a way to avoid this code
duplication).
Cc: Greg Kurz <[email protected]>
Signed-off-by: Michael S. Tsirkin <[email protected]>
|
|
Makes them more generally available.
Signed-off-by: Michael S. Tsirkin <[email protected]>
|
|
The virtio core uses a static ida named virtio_index_ida for
assigning index numbers to virtio devices during registration.
The ida core may allocate some internal idr cache layers and
an ida bitmap upon any ida allocation, and all these layers are
truely freed only upon the ida destruction. The virtio_index_ida
is not destroyed at present, leading to a memory leak when using
the virtio core as a module and atleast one virtio device is
registered and unregistered.
Fix this by invoking ida_destroy() in the virtio core module
exit.
Cc: [email protected]
Signed-off-by: Suman Anna <[email protected]>
Signed-off-by: Michael S. Tsirkin <[email protected]>
|
|
commit 5d9a07b0de512b77bf28d2401e5fe3351f00a240 ("vhost: relax used
address alignment") fixed the alignment for the used virtual address,
but not for the physical address used for logging.
That's a mistake: alignment should clearly be the same for virtual and
physical addresses,
Cc: [email protected]
Signed-off-by: Michael S. Tsirkin <[email protected]>
|
|
page reads
Every attempt to issue a read log page command lockup the controller.
The command is currently sent if the sata device includes the devlsp feature
to read out the timing data.
This attempt to read the data, locks up the controller and the device
is not recognzied correctly (failed to set xfermode) and cannot be accessed.
This was found on Freescale P1013/P1022 and T4240 CPUs
using a ATP IG mSATA 4GB with the devslp feature.
fsl-sata ff718000.sata: Sata FSL Platform/CSB Driver init
[ 1.254195] scsi0 : sata_fsl
[ 1.256004] ata1: SATA max UDMA/133 irq 74
[ 1.370666] fsl-gianfar ethernet.3: enabled errata workarounds, flags: 0x4
[ 1.470671] fsl-gianfar ethernet.4: enabled errata workarounds, flags: 0x4
[ 1.775584] ata1: Signature Update detected @ 504 msecs
[ 1.947594] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.948366] ata1.00: ATA-8: ATP IG mSATA, 20150311, max UDMA/133
[ 1.948371] ata1.00: 7732368 sectors, multi 0: LBA
[ 1.948843] ata1.00: failed to get Identify Device Data, Emask 0x1
[ 1.948857] ata1.00: failed to set xfermode (err_mask=0x40)
[ 7.467557] ata1: Signature Update detected @ 504 msecs
[ 7.639560] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 7.651320] ata1.00: failed to get Identify Device Data, Emask 0x1
[ 7.651360] ata1.00: failed to set xfermode (err_mask=0x40)
[ 7.655628] ata1: limiting SATA link speed to 1.5 Gbps
[ 7.659458] ata1.00: limiting speed to UDMA/133:PIO3
[ 13.163554] ata1: Signature Update detected @ 504 msecs
[ 13.335558] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 13.347298] ata1.00: failed to get Identify Device Data, Emask 0x1
[ 13.347334] ata1.00: failed to set xfermode (err_mask=0x40)
[ 13.351601] ata1.00: disabled
[ 13.353278] ata1: exception Emask 0x50 SAct 0x0 SErr 0x800 action 0x6 frozen t4
[ 13.359281] ata1: SError: { HostInt }
[ 13.361644] ata1: hard resetting link
Signed-off-by: Andreas Werner <[email protected]>
Signed-off-by: Tejun Heo <[email protected]>
|
|
log page
Some controller lockup on a ata_read_log_page.
Add new ata port flag ATA_FLAG_NO_LOG_PAGE which can used
to blacklist a controller.
If this flag is set, any attempt to read a log page returns an error
without actually issuing the command.
Signed-off-by: Andreas Werner <[email protected]>
Signed-off-by: Tejun Heo <[email protected]>
|
|
The following commit which went into mainline through networking tree
3b13758f51de ("cgroups: Allow dynamically changing net_classid")
conflicts in net/core/netclassid_cgroup.c with the following pending
fix in cgroup/for-4.4-fixes.
1f7dd3e5a6e4 ("cgroup: fix handling of multi-destination migration from subtree_control enabling")
The former separates out update_classid() from cgrp_attach() and
updates it to walk all fds of all tasks in the target css so that it
can be used from both migration and config change paths. The latter
drops @css from cgrp_attach().
Resolve the conflict by making cgrp_attach() call update_classid()
with the css from the first task. We can revive @tset walking in
cgrp_attach() but given that net_cls is v1 only where there always is
only one target css during migration, this is fine.
Signed-off-by: Tejun Heo <[email protected]>
Reported-by: Stephen Rothwell <[email protected]>
Cc: Nina Schiff <[email protected]>
|
|
Once virtio starts using the DMA API, we won't be able to safely DMA
from the stack. virtio-net does a couple of config DMA requests
from small stack buffers -- switch to using dynamically-allocated
memory.
This should have no effect on any performance-critical code paths.
Reported-by: Andy Lutomirski <[email protected]>
Signed-off-by: Michael S. Tsirkin <[email protected]>
Tested-by: Andy Lutomirski <[email protected]>
|
|
On the internal mic of the Packard Bell DOTS, one channel
has an inverted signal. Add a quirk to fix this up.
Cc: [email protected]
BugLink: https://bugs.launchpad.net/bugs/1523232
Signed-off-by: David Henningsson <[email protected]>
Signed-off-by: Takashi Iwai <[email protected]>
|
|
In BXT-P A0, HD-Audio DMA requests is later than expected,
and makes an audio stream sensitive to system latencies when
24/32 bits are playing.
Adjusting threshold of DMA fifo to force the DMA request
sooner to improve latency tolerance at the expense of power.
v2: move Intel specific code to hda_intel.c
Signed-off-by: Lu, Han <[email protected]>
Signed-off-by: Takashi Iwai <[email protected]>
|
|
|
|
The ioctl IOC_LIBCFS_PING_TEST has not been used in ages. The recent
nidstring changes which moved all the nidstring operations from libcfs
to the LNet layer but this ioctl code was still using an nidstring
operation that was causing a circular dependency loop between libcfs and
LNet.
Signed-off-by: James Simmons <[email protected]>
Signed-off-by: Oleg Drokin <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"A couple of fixes (-stable fodder) + dead code removal after the
overlayfs fix.
I agree that it's better to separate from the fix part to make
backporting easier, but IMO it's not worth delaying said dead code
removal until the next window"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
Don't reset ->total_link_count on nested calls of vfs_path_lookup()
ovl: get rid of the dead code left from broken (and disabled) optimizations
ovl: fix permission checking for setattr
|
|
we already zero it on outermost set_nameidata(), so initialization in
path_init() is pointless and wrong. The same DoS exists on pre-4.2
kernels, but there a slightly different fix will be needed.
Cc: [email protected] # v4.2
Signed-off-by: Al Viro <[email protected]>
|
|
Signed-off-by: Al Viro <[email protected]>
|
|
[Al Viro] The bug is in being too enthusiastic about optimizing ->setattr()
away - instead of "copy verbatim with metadata" + "chmod/chown/utimes"
(with the former being always safe and the latter failing in case of
insufficient permissions) it tries to combine these two. Note that copyup
itself will have to do ->setattr() anyway; _that_ is where the elevated
capabilities are right. Having these two ->setattr() (one to set verbatim
copy of metadata, another to do what overlayfs ->setattr() had been asked
to do in the first place) combined is where it breaks.
Signed-off-by: Miklos Szeredi <[email protected]>
Cc: <[email protected]>
Signed-off-by: Al Viro <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Thomas Gleixner:
"This updates contains the following changes:
- Fix a signal handling regression in the bit wait functions.
- Avoid false positive warnings in the wakeup path.
- Initialize the scheduler root domain properly.
- Handle gtime calculations in proc/$PID/stat proper.
- Add more documentation for the barriers in try_to_wake_up().
- Fix a subtle race in try_to_wake_up() which might cause a task to
be scheduled on two cpus
- Compile static helper function only when it is used"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/core: Fix an SMP ordering race in try_to_wake_up() vs. schedule()
sched/core: Better document the try_to_wake_up() barriers
sched/cputime: Fix invalid gtime in proc
sched/core: Clear the root_domain cpumasks in init_rootdomain()
sched/core: Remove false-positive warning from wake_up_process()
sched/wait: Fix signal handling in bit wait helpers
sched/rt: Hide the push_irq_work_func() declaration
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thoma Gleixner:
"Another round of fixes for x86:
- Move the initialization of the microcode driver to late_initcall to
make sure everything that init function needs is available.
- Make sure that lockdep knows about interrupts being off in the
entry code before calling into c-code.
- Undo the cpu hotplug init delay regression.
- Use the proper conditionals in the mpx instruction decoder.
- Fixup restart_syscall for x32 tasks.
- Fix the hugepage regression on PAE kernels which was introduced
with the latest PAT changes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/signal: Fix restart_syscall number for x32 tasks
x86/mpx: Fix instruction decoder condition
x86/mm: Fix regression with huge pages on PAE
x86 smpboot: Re-enable init_udelay=0 by default on modern CPUs
x86/entry/64: Fix irqflag tracing wrt context tracking
x86/microcode: Initialize the driver late when facilities are up
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is quite a bumper crop of fixes: three from Arnd correcting
various build issues in some configurations, a lock recursion in
qla2xxx. Two potentially exploitable issues in hpsa and mvsas, a
potential null deref in st, a revert of a bdi registration fix that
turned out to cause even more problems, a set of fixes to allow people
who only defined MPT2SAS to still work after the mpt2/mpt3sas merger
and a couple of fixes for issues turned up by the hyper-v storvsc
driver"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
mpt3sas: fix Kconfig dependency problem for mpt2sas back compatibility
Revert "scsi: Fix a bdi reregistration race"
mpt3sas: Add dummy Kconfig option for backwards compatibility
Fix a memory leak in scsi_host_dev_release()
block/sd: Fix device-imposed transfer length limits
scsi_debug: fix prevent_allow+verify regressions
MAINTAINERS: Add myself as co-maintainer of the SCSI subsystem.
sd: Make discard granularity match logical block size when LBPRZ=1
scsi: hpsa: select CONFIG_SCSI_SAS_ATTR
scsi: advansys needs ISA dma api for ISA support
scsi_sysfs: protect against double execution of __scsi_remove_device()
st: fix potential null pointer dereference.
scsi: report 'INQUIRY result too short' once per host
advansys: fix big-endian builds
qla2xxx: Fix rwlock recursion
hpsa: logical vs bitwise AND typo
mvsas: don't allow negative timeouts
mpt3sas: Fix use sas_is_tlr_enabled API before enabling MPI2_SCSIIO_CONTROL_TLR_ON flag
|
|
In case we monitor events system wide, we get EXIT event
(when configured) twice for each task that exited.
Note doubled lines with same pid/tid in following example:
$ sudo ./perf record -a
^C[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.480 MB perf.data (2518 samples) ]
$ sudo ./perf report -D | grep EXIT
0 60290687567581 0x59910 [0x38]: PERF_RECORD_EXIT(1250:1250):(1250:1250)
0 60290687568354 0x59948 [0x38]: PERF_RECORD_EXIT(1250:1250):(1250:1250)
0 60290687988744 0x59ad8 [0x38]: PERF_RECORD_EXIT(1250:1250):(1250:1250)
0 60290687989198 0x59b10 [0x38]: PERF_RECORD_EXIT(1250:1250):(1250:1250)
1 60290692567895 0x62af0 [0x38]: PERF_RECORD_EXIT(1253:1253):(1253:1253)
1 60290692568322 0x62b28 [0x38]: PERF_RECORD_EXIT(1253:1253):(1253:1253)
2 60290692739276 0x69a18 [0x38]: PERF_RECORD_EXIT(1252:1252):(1252:1252)
2 60290692739910 0x69a50 [0x38]: PERF_RECORD_EXIT(1252:1252):(1252:1252)
The reason is that the cpu contexts are processes each time
we call perf_event_task. I'm changing the perf_event_aux logic
to serve task_ctx and cpu contexts separately, which ensure we
don't get EXIT event generated twice on same cpu context.
This does not affect other auxiliary events, as they don't
use task_ctx at all.
Signed-off-by: Jiri Olsa <[email protected]>
Signed-off-by: Peter Zijlstra (Intel) <[email protected]>
Cc: Arnaldo Carvalho de Melo <[email protected]>
Cc: Arnaldo Carvalho de Melo <[email protected]>
Cc: David Ahern <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Stephane Eranian <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: Vince Weaver <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Ingo Molnar <[email protected]>
|
|
We need to add rest of the flags to the constraint mask
instead of another INTEL_ARCH_EVENT_MASK, fixing a typo.
Signed-off-by: Jiri Olsa <[email protected]>
Signed-off-by: Peter Zijlstra (Intel) <[email protected]>
Cc: Arnaldo Carvalho de Melo <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: Paul Mackerras <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Stephane Eranian <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: Vince Weaver <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Ingo Molnar <[email protected]>
|
|
There was a mistake in the Haswell constraints table.
Signed-off-by: Yuanfang Chen <[email protected]>
Signed-off-by: Peter Zijlstra (Intel) <[email protected]>
Reviewed-by: Andi Kleen <[email protected]>
Cc: Arnaldo Carvalho de Melo <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Stephane Eranian <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: Vince Weaver <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Ingo Molnar <[email protected]>
|
|
Pull drm fixes from Dave Airlie:
"A bunch of change across the board, the main things are some vblank
fallout in radeon and nouveau required some work, but I think this
should fix it all. There is also one drm fix for an oops in vmwgfx
with how we pass the drm master around.
The rest is just some amdgpu, i915, imx and rockchip fixes.
Probably more than I'd like at this point, but hopefully things settle
down now"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (40 commits)
drm/amdgpu: Fixup hw vblank counter/ts for new drm_update_vblank_count() (v3)
drm/radeon: Fixup hw vblank counter/ts for new drm_update_vblank_count() (v2)
drm/radeon: Retry DDC probing on DVI on failure if we got an HPD interrupt
drm/amdgpu: add spin lock to protect freed list in vm (v2)
drm/amdgpu: partially revert "drm/amdgpu: fix VM_CONTEXT*_PAGE_TABLE_END_ADDR" v2
drm/amdgpu: take a BO reference for the user fence
drm/amdgpu: take a BO reference in the display code
drm/amdgpu: set snooped flags only on system addresses v2
drm/nouveau: Fix pre-nv50 pageflip events (v4)
drm: Fix an unwanted master inheritance v2
drm/amdgpu: fix race condition in amd_sched_entity_push_job
drm/amdgpu: add err check for pin userptr
drm/i915: take a power domain reference while checking the HDMI live status
drm/i915: add MISSING_CASE to a few port/aux power domain helpers
drm/i915/ddi: fix intel_display_port_aux_power_domain() after HDMI detect
drm/i915: Introduce a gmbus power domain
drm/i915: Clean up AUX power domain handling
drm/rockchip: Use CRTC vblank event interface
drm/rockchip: Fix module autoload for OF platform driver
drm/rockchip: vop: fix window origin calculation
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
"This fixes a couple of crypto drivers that were using memcmp to verify
authentication tags. They now use crypto_memneq instead"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: talitos - Fix timing leak in ESP ICV verification
crypto: nx - Fix timing leak in GCM and CCM decryption
|
|
When restarting a syscall with regs->ax == -ERESTART_RESTARTBLOCK,
regs->ax is assigned to a restart_syscall number. For x32 tasks, this
syscall number must have __X32_SYSCALL_BIT set, otherwise it will be
an x86_64 syscall number instead of a valid x32 syscall number. This
issue has been there since the introduction of x32.
Reported-by: strace/tests/restart_syscall.test
Reported-and-tested-by: Elvira Khabirova <[email protected]>
Signed-off-by: Dmitry V. Levin <[email protected]>
Cc: Elvira Khabirova <[email protected]>
Cc: [email protected]
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Thomas Gleixner <[email protected]>
|
|
MPX decodes instructions in order to tell which bounds register
was violated. Part of this decoding involves looking at the "REX
prefix" which is a special instrucion prefix used to retrofit
support for new registers in to old instructions.
The X86_REX_*() macros are defined to return actual bit values:
#define X86_REX_R(rex) ((rex) & 4)
*not* boolean values. However, the MPX code was checking for
them like they were booleans. This might have led to us
mis-decoding the "REX prefix" and giving false information out to
userspace about bounds violations. X86_REX_B() actually is bit 1,
so this is really only broken for the X86_REX_X() case.
Fix the conditionals up to tolerate the non-boolean values.
Fixes: fcc7ffd67991 "x86, mpx: Decode MPX instruction to get bound violation information"
Reported-by: Dan Carpenter <[email protected]>
Signed-off-by: Dave Hansen <[email protected]>
Cc: [email protected]
Cc: Dave Hansen <[email protected]>
Cc: [email protected]
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Thomas Gleixner <[email protected]>
|
|
into drm-next
A few more last minute fixes for 4.4 on top of my pull request from
earlier this week. The big change here is a vblank regression fix due to
commit 4dfd6486 "drm: Use vblank timestamps to guesstimate how many vblanks
were missed". Beyond that, a hotplug fix and a few VM fixes.
* 'drm-fixes-4.4' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: Fixup hw vblank counter/ts for new drm_update_vblank_count() (v3)
drm/radeon: Fixup hw vblank counter/ts for new drm_update_vblank_count() (v2)
drm/radeon: Retry DDC probing on DVI on failure if we got an HPD interrupt
drm/amdgpu: add spin lock to protect freed list in vm (v2)
drm/amdgpu: partially revert "drm/amdgpu: fix VM_CONTEXT*_PAGE_TABLE_END_ADDR" v2
drm/amdgpu: take a BO reference for the user fence
drm/amdgpu: take a BO reference in the display code
drm/amdgpu: set snooped flags only on system addresses v2
drm/amdgpu: fix race condition in amd_sched_entity_push_job
drm/amdgpu: add err check for pin userptr
add blacklist for thinkpad T40p
drm/amdgpu: fix VM page table reference counting
drm/amdgpu: fix userptr flags check
|