| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
pm8001_phy_control() populates the enable_completion pointer with a stack
address, sends a PHY_LINK_RESET / PHY_HARD_RESET, waits 300 ms, and
returns. The problem arises when a phy control response comes late. After
300 ms the pm8001_phy_control() function returns and the passed
enable_completion stack address is no longer valid. Late phy control
response invokes complete() on a dangling enable_completion pointer which
leads to a kernel crash.
Signed-off-by: Igor Pylypiv <[email protected]>
Signed-off-by: Terrence Adams <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Acked-by: Jack Wang <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
If host tries to remove ufshcd driver from a UFS device it would cause a
kernel panic if ufshcd_async_scan fails during ufshcd_probe_hba before
adding a SCSI host with scsi_add_host and MCQ is enabled since SCSI host
has been defered after MCQ configuration introduced by commit 0cab4023ec7b
("scsi: ufs: core: Defer adding host to SCSI if MCQ is supported").
To guarantee that SCSI host is removed only if it has been added, set the
scsi_host_added flag to true after adding a SCSI host and check whether it
is set or not before removing it.
Signed-off-by: Kyoungrul Kim <[email protected]>
Signed-off-by: Minwoo Im <[email protected]>
Link: https://lore.kernel.org/r/20240627085104epcms2p5897a3870ea5c6416aa44f94df6c543d7@epcms2p5
Reviewed-by: Bart Van Assche <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
Enable suspending clk scaling on no request for Qualcomm SoC.
Signed-off-by: Ram Prakash Gupta <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Bart Van Assche <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
Currently UFS clk scaling is getting suspended only when the clks are
scaled down. When high load is generated, a huge amount of latency is added
due to scaling up the clk and completing the request post that.
Suspending the scaling in its existing state when high load is generated
improves the random performance KPI by 28%. So suspending the scaling when
there are no requests. And the clk would be put in low scaled state when
the actual request load is low.
Make this change optional by having the check enabled using vops since for
some devices suspending without bringing the clk in low scaled state might
have impact on power consumption of the SoC.
Signed-off-by: Ram Prakash Gupta <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Bart Van Assche <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
The test for a possible shift overflow is not correct. Fix it by replacing
the '>' with a '>='.
Signed-off-by: Tomas Henzl <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Suggested-by: Dan Carpenter <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
Ranjan Kumar <[email protected]> says:
The controllers managed by mpi3mr driver requires system memory to
save hardware and firmware diagnostic information, this patch set
enhances the drivers to provide host memory to the controller for
diagnostic information. This patch set also provides driver changes
to push kernel messages into the diagnostic buffers reserved for the
driver, so that the information will be available as part of debug
data fetched from the controller. In addition, support for
configuring automatic diagnostic information is added in the driver.
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
Update driver version to 8.9.1.0.50
Signed-off-by: Ranjan Kumar <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
Add interface for applications to manage the host diagnostic buffers and
update the automatic diag buffer capture triggers.
Co-developed-by: Sathya Prakash <[email protected]>
Signed-off-by: Sathya Prakash <[email protected]>
Signed-off-by: Ranjan Kumar <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
Add functions to process automatic diag triggers. If a condition defined in
the triggers is met, the driver will call appropriate controller functions
to save the diagnostic information.
Reported-by: kernel test robot <[email protected]>
Closes: https://lore.kernel.org/oe-kbuild-all/[email protected]/
Co-developed-by: Sathya Prakash <[email protected]>
Signed-off-by: Sathya Prakash <[email protected]>
Signed-off-by: Ranjan Kumar <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
To be able to debug controller problems it is beneficial to allocate and
configure system/host memory buffers which can be used to capture hardware
and firmware diagnostic information.
Add functions required to allocate and post firmware and hardware
diagnostic buffers to the controller and to set up automatic diagnostic
capture triggers.
Captures will be triggered under the following circumstances:
1. Firmware is in FAULT state.
2. Admin commands time out.
3. Controller reset caused due to I/O timeout
Reported-by: kernel test robot <[email protected]>
Closes: https://lore.kernel.org/oe-kbuild-all/[email protected]/
Co-developed-by: Sathya Prakash <[email protected]>
Signed-off-by: Sathya Prakash <[email protected]>
Signed-off-by: Ranjan Kumar <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
Add PCI ID to support Intel Panther Lake, same as MTL.
Signed-off-by: Adrian Hunter <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Bart Van Assche <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
With ARCH=arm64, make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/ufs/host/ufs-qcom.o
Add the missing invocation of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
In function lpfc_xcvr_data_show, the memory allocation with kmalloc might
fail, thereby making rdp_context a null pointer. In the following context
and functions that use this pointer, there are dereferencing operations,
leading to null pointer dereference.
To fix this issue, a null pointer check should be added. If it is null,
use scnprintf to notify the user and return len.
Fixes: 479b0917e447 ("scsi: lpfc: Create a sysfs entry called lpfc_xcvr_data for transceiver info")
Signed-off-by: Huai-Yuan Liu <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Justin Tee <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
again after probe failed
The expander phy will be treated as broadcast flutter in the next
revalidation after the exp-attached end device probe failed, as follows:
[78779.654026] sas: broadcast received: 0
[78779.654037] sas: REVALIDATING DOMAIN on port 0, pid:10
[78779.654680] sas: ex 500e004aaaaaaa1f phy05 change count has changed
[78779.662977] sas: ex 500e004aaaaaaa1f phy05 originated BROADCAST(CHANGE)
[78779.662986] sas: ex 500e004aaaaaaa1f phy05 new device attached
[78779.663079] sas: ex 500e004aaaaaaa1f phy05:U:8 attached: 500e004aaaaaaa05 (stp)
[78779.693542] hisi_sas_v3_hw 0000:b4:02.0: dev[16:5] found
[78779.701155] sas: done REVALIDATING DOMAIN on port 0, pid:10, res 0x0
[78779.707864] sas: Enter sas_scsi_recover_host busy: 0 failed: 0
...
[78835.161307] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[78835.171344] sas: sas_probe_sata: for exp-attached device 500e004aaaaaaa05 returned -19
[78835.180879] hisi_sas_v3_hw 0000:b4:02.0: dev[16:5] is gone
[78835.187487] sas: broadcast received: 0
[78835.187504] sas: REVALIDATING DOMAIN on port 0, pid:10
[78835.188263] sas: ex 500e004aaaaaaa1f phy05 change count has changed
[78835.195870] sas: ex 500e004aaaaaaa1f phy05 originated BROADCAST(CHANGE)
[78835.195875] sas: ex 500e004aaaaaaa1f rediscovering phy05
[78835.196022] sas: ex 500e004aaaaaaa1f phy05:U:A attached: 500e004aaaaaaa05 (stp)
[78835.196026] sas: ex 500e004aaaaaaa1f phy05 broadcast flutter
[78835.197615] sas: done REVALIDATING DOMAIN on port 0, pid:10, res 0x0
The cause of the problem is that the related ex_phy's attached_sas_addr was
not cleared after the end device probe failed, so reset it.
Signed-off-by: Xingui Yang <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: John Garry <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
Target debugfs entry is removed via async_schedule() which isn't drained
when adding same name target, so failure of "Directory 'target11:0:0' with
parent 'scsi_debug' already present!" can be triggered easily.
Fix it by switching to domain async schedule, and draining it before
adding new target debugfs entry.
Cc: Wenchao Hao <[email protected]>
Fixes: f084fe52c640 ("scsi: scsi_debug: Add debugfs interface to fail target reset")
Signed-off-by: Ming Lei <[email protected]>
Acked-by: Wenchao Hao <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
USB/UAS devices
Recently it was reported that the following USB storage devices are
unusable with Linux kernel 6.9:
* Kingston DataTraveler G2
* Garmin FR35
This is because attempting to read the IO Advice Hints Grouping mode page
causes these devices to reset. Hence do not read the IO Advice Hints
Grouping mode page from USB/UAS storage devices.
Acked-by: Alan Stern <[email protected]>
Cc: [email protected]
Fixes: 4f53138fffc2 ("scsi: sd: Translate data lifetime information")
Reported-by: Joao Machado <[email protected]>
Closes: https://lore.kernel.org/linux-scsi/[email protected]/T/#mf4e3410d8f210454d7e4c3d1fb5c0f41e651b85f
Tested-by: Andy Shevchenko <[email protected]>
Bisected-by: Christian Heusel <[email protected]>
Reported-by: Andy Shevchenko <[email protected]>
Closes: https://lore.kernel.org/linux-scsi/CACLx9VdpUanftfPo2jVAqXdcWe8Y43MsDeZmMPooTzVaVJAh2w@mail.gmail.com/
Signed-off-by: Bart Van Assche <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
Prepare for skipping the IO Advice Hints Grouping mode page for USB storage
devices.
Cc: Alan Stern <[email protected]>
Cc: Joao Machado <[email protected]>
Cc: Andy Shevchenko <[email protected]>
Cc: Christian Heusel <[email protected]>
Cc: [email protected]
Fixes: 4f53138fffc2 ("scsi: sd: Translate data lifetime information")
Signed-off-by: Bart Van Assche <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
Under the conditions that a device is to be reinitialized within
ufshcd_probe_hba(), the device must first be fully reset.
Resetting the device should include freeing U8 model (member of dev_info)
but does not, and this causes a memory leak. ufs_put_device_desc() is
responsible for freeing model.
unreferenced object 0xffff3f63008bee60 (size 32):
comm "kworker/u33:1", pid 60, jiffies 4294892642
hex dump (first 32 bytes):
54 48 47 4a 46 47 54 30 54 32 35 42 41 5a 5a 41 THGJFGT0T25BAZZA
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace (crc ed7ff1a9):
[<ffffb86705f1243c>] kmemleak_alloc+0x34/0x40
[<ffffb8670511cee4>] __kmalloc_noprof+0x1e4/0x2fc
[<ffffb86705c247fc>] ufshcd_read_string_desc+0x94/0x190
[<ffffb86705c26854>] ufshcd_device_init+0x480/0xdf8
[<ffffb86705c27b68>] ufshcd_probe_hba+0x3c/0x404
[<ffffb86705c29264>] ufshcd_async_scan+0x40/0x370
[<ffffb86704f43e9c>] async_run_entry_fn+0x34/0xe0
[<ffffb86704f34638>] process_one_work+0x154/0x298
[<ffffb86704f34a74>] worker_thread+0x2f8/0x408
[<ffffb86704f3cfa4>] kthread+0x114/0x118
[<ffffb86704e955a0>] ret_from_fork+0x10/0x20
Fixes: 96a7141da332 ("scsi: ufs: core: Add support for reinitializing the UFS device")
Cc: <[email protected]>
Reviewed-by: Andrew Halaney <[email protected]>
Reviewed-by: Bart Van Assche <[email protected]>
Signed-off-by: Joel Slebodnick <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
The comment that scsi_static_device_list would go away was added more than
18 years ago. Today, that list is still there and a large number of
additional entries have been added. This shows that this comment is
incorrect. Hence fix that comment.
Cc: Christoph Hellwig <[email protected]>
Cc: Avri Altman <[email protected]>
Signed-off-by: Bart Van Assche <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
The function mpi3mr_qcmd() of the mpi3mr driver is able to indicate to
the HBA if a read or write command directed at an ATA device should be
translated to an NCQ read/write command with the high prioiryt bit set
when the request uses the RT priority class and the user has enabled NCQ
priority through sysfs.
However, unlike the mpt3sas driver, the mpi3mr driver does not define
the sas_ncq_prio_supported and sas_ncq_prio_enable sysfs attributes, so
the ncq_prio_enable field of struct mpi3mr_sdev_priv_data is never
actually set and NCQ Priority cannot ever be used.
Fix this by defining these missing atributes to allow a user to check if
an ATA device supports NCQ priority and to enable/disable the use of NCQ
priority. To do this, lift the function scsih_ncq_prio_supp() out of the
mpt3sas driver and make it the generic SCSI SAS transport function
sas_ata_ncq_prio_supported(). Nothing in that function is hardware
specific, so this function can be used in both the mpt3sas driver and
the mpi3mr driver.
Reported-by: Scott McCoy <[email protected]>
Fixes: 023ab2a9b4ed ("scsi: mpi3mr: Add support for queue command processing")
Cc: [email protected]
Signed-off-by: Damien Le Moal <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Niklas Cassel <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
On x86, make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/scsi/scsi_common.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/scsi/advansys.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/scsi/BusLogic.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/scsi/aha1740.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/scsi/isci/isci.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/scsi/elx/efct.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/scsi/atp870u.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/scsi/ppa.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/scsi/imm.o
Add all missing invocations of the MODULE_DESCRIPTION() macro.
This updates all files which have a MODULE_LICENSE() but which do not have
a MODULE_DESCRIPTION(), even ones which did not produce the x86
allmodconfig warnings.
Acked-by: Finn Thain <[email protected]>
Signed-off-by: Jeff Johnson <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
In ufshcd_clock_scaling_prepare(), after SCSI layer is blocked,
ufshcd_pending_cmds() is called to check whether there are pending
transactions or not. And only if there are no pending transactions can we
proceed to kickstart the clock scaling sequence.
ufshcd_pending_cmds() traverses over all SCSI devices and calls
sbitmap_weight() on their budget_map. sbitmap_weight() can be broken down
to three steps:
1. Calculate the nr outstanding bits set in the 'word' bitmap.
2. Calculate the nr outstanding bits set in the 'cleared' bitmap.
3. Subtract the result from step 1 by the result from step 2.
This can lead to a race condition as outlined below:
Assume there is one pending transaction in the request queue of one SCSI
device, say sda, and the budget token of this request is 0, the 'word' is
0x1 and the 'cleared' is 0x0.
1. When step 1 executes, it gets the result as 1.
2. Before step 2 executes, block layer tries to dispatch a new request to
sda. Since the SCSI layer is blocked, the request cannot pass through
SCSI but the block layer would do budget_get() and budget_put() to
sda's budget map regardless, so the 'word' has become 0x3 and 'cleared'
has become 0x2 (assume the new request got budget token 1).
3. When step 2 executes, it gets the result as 1.
4. When step 3 executes, it gets the result as 0, meaning there is no
pending transactions, which is wrong.
Thread A Thread B
ufshcd_pending_cmds() __blk_mq_sched_dispatch_requests()
| |
sbitmap_weight(word) |
| scsi_mq_get_budget()
| |
| scsi_mq_put_budget()
| |
sbitmap_weight(cleared)
...
When this race condition happens, the clock scaling sequence is started
with transactions still in flight, leading to subsequent hibernate enter
failure, broken link, task abort and back to back error recovery.
Fix this race condition by quiescing the request queues before calling
ufshcd_pending_cmds() so that block layer won't touch the budget map when
ufshcd_pending_cmds() is working on it. In addition, remove the SCSI layer
blocking/unblocking to reduce redundancies and latencies.
Fixes: 8d077ede48c1 ("scsi: ufs: Optimize the command queueing code")
Co-developed-by: Can Guo <[email protected]>
Signed-off-by: Can Guo <[email protected]>
Signed-off-by: Ziqi Chen <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Bart Van Assche <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
For SCSI devices supporting the Command Duration Limits feature set, the
user can enable/disable this feature use through the sysfs device attribute
"cdl_enable". This attribute modification triggers a call to
scsi_cdl_enable() to enable and disable the feature for ATA devices and set
the scsi device cdl_enable field to the user provided bool value. For SCSI
devices supporting CDL, the feature set is always enabled and
scsi_cdl_enable() is reduced to setting the cdl_enable field.
However, for ATA devices, a drive may spin-up with the CDL feature enabled
by default. But the SCSI device cdl_enable field is always initialized to
false (CDL disabled), regardless of the actual device CDL feature
state. For ATA devices managed by libata (or libsas), libata-core always
disables the CDL feature set when the device is attached, thus syncing the
state of the CDL feature on the device and of the SCSI device cdl_enable
field. However, for ATA devices connected to a SAS HBA, the CDL feature is
not disabled on scan for ATA devices that have this feature enabled by
default, leading to an inconsistent state of the feature on the device with
the SCSI device cdl_enable field.
Avoid this inconsistency by adding a call to scsi_cdl_enable() in
scsi_cdl_check() to make sure that the device-side state of the CDL feature
set always matches the scsi device cdl_enable field state. This implies
that CDL will always be disabled for ATA devices connected to SAS HBAs,
which is consistent with libata/libsas initialization of the device.
Reported-by: Scott McCoy <[email protected]>
Fixes: 1b22cfb14142 ("scsi: core: Allow enabling and disabling command duration limits")
Cc: [email protected]
Signed-off-by: Damien Le Moal <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Niklas Cassel <[email protected]>
Reviewed-by: Igor Pylypiv <[email protected]>
Reviewed-by: Hannes Reinecke <[email protected]>
Reviewed-by: Christoph Hellwig <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
There is a potential out-of-bounds access when using test_bit() on a single
word. The test_bit() and set_bit() functions operate on long values, and
when testing or setting a single word, they can exceed the word
boundary. KASAN detects this issue and produces a dump:
BUG: KASAN: slab-out-of-bounds in _scsih_add_device.constprop.0 (./arch/x86/include/asm/bitops.h:60 ./include/asm-generic/bitops/instrumented-atomic.h:29 drivers/scsi/mpt3sas/mpt3sas_scsih.c:7331) mpt3sas
Write of size 8 at addr ffff8881d26e3c60 by task kworker/u1536:2/2965
For full log, please look at [1].
Make the allocation at least the size of sizeof(unsigned long) so that
set_bit() and test_bit() have sufficient room for read/write operations
without overwriting unallocated memory.
[1] Link: https://lore.kernel.org/all/[email protected]/
Fixes: c696f7b83ede ("scsi: mpt3sas: Implement device_remove_in_progress check in IOCTL path")
Cc: [email protected]
Suggested-by: Keith Busch <[email protected]>
Signed-off-by: Breno Leitao <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Keith Busch <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
Commit 321da3dc1f3c ("scsi: sd: usb_storage: uas: Access media prior
to querying device properties") triggered a read to LBA 0 before
attempting to inquire about device characteristics. This was done
because some protocol bridge devices will return generic values until
an attached storage device's media has been accessed.
Pierre Tomon reported that this change caused problems on a large
capacity external drive connected via a bridge device. The bridge in
question does not appear to implement the READ(10) command.
Issue a READ(16) instead of READ(10) when a device has been identified
as preferring 16-byte commands (use_16_for_rw heuristic).
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218890
Link: https://lore.kernel.org/r/[email protected]
Link: https://lore.kernel.org/r/[email protected]
Fixes: 321da3dc1f3c ("scsi: sd: usb_storage: uas: Access media prior to querying device properties")
Cc: [email protected]
Reported-by: Pierre Tomon <[email protected]>
Suggested-by: Alan Stern <[email protected]>
Tested-by: Pierre Tomon <[email protected]>
Reviewed-by: Bart Van Assche <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
Bart Van Assche <[email protected]> says:
Hi Martin,
There are several 32-bit ARM SCSI drivers that trigger compiler warnings
about missing function declarations. This patch series fixes these
compiler warnings by declaring local functions static. Please consider
this patch series for the next merge window.
Thanks,
Bart.
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
Signed-off-by: Bart Van Assche <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Johannes Thumshirn <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
Signed-off-by: Bart Van Assche <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Johannes Thumshirn <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
Signed-off-by: Bart Van Assche <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Johannes Thumshirn <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
Signed-off-by: Bart Van Assche <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Johannes Thumshirn <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
Minwoo Im <[email protected]> says:
This patchset introduces add support for MCQ introduced in UFSHCI 4.0.
The first patch adds a simple helper to get the address of MCQ queue
config registers. The second one enables MCQ feature by adding mandatory
vops callback functions required at MCQ initialization phase. The last
one is to prevent a case where number of MCQ is given 1 since driver
allocates poll_queues first rather than I/O queues to handle device
commands. Instead of causing exception handlers due to no I/O queue,
failfast during the initialization time.
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
If hba_maxq equals poll_queues, which means there are no I/O queues
(HCTX_TYPE_DEFAULT, HCTX_TYPE_READ), the very first hw queue will be
allocated as HCTX_TYPE_POLL and it will be used as the dev_cmd_queue. In
this case, device commands such as QUERY cannot be properly handled.
This patch prevents the initialization of MCQ when the number of I/O queues
is not set and only the number of POLL queues is set.
Signed-off-by: Minwoo Im <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Bart Van Assche <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
Recently, ufs-mcq feature has been introduced to QEMU hw/ufs device [1].
This patch adds MCQ support for upstream QEMU UFS PCI controller. This
patch provides mandatory vops callbacks to make UFS controller work
properly on MCQ mode. Operation and Runtime Config register stride is
fixed to 48bytes which is implemented by qemu.
[1] https://lore.kernel.org/qemu-devel/[email protected]/
Signed-off-by: Minwoo Im <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Bart Van Assche <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
Inline functions are preferred over macros. Convert the MCQ_CFG_n macro to
an inline function.
Signed-off-by: Minwoo Im <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Bart Van Assche <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
The MCQ_OPR_OFFSET_n macro takes 'hba' in the caller context without
receiving 'hba' instance as an argument. To prevent potential bugs in
future use cases, add an argument 'hba'.
Fixes: 2468da61ea09 ("scsi: ufs: core: mcq: Configure operation and runtime interface")
Cc: Asutosh Das <[email protected]>
Signed-off-by: Minwoo Im <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Bart Van Assche <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
An error unrelated to ufshcd_try_to_abort_task is being logged and can
cause confusion. Modify ufshcd_mcq_abort() to print the result of the abort
failure. For readability, return immediately instead of 'goto'.
Fixes: f1304d442077 ("scsi: ufs: mcq: Added ufshcd_mcq_abort()")
Signed-off-by: Chanwoo Lee <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Bart Van Assche <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
Avri Altman <[email protected]> says:
The rtt-upiu packets precede any data-out upiu packets, thus synchronizing
the data input to the device: this mostly applies to write operations, but
there are other operations that requires rtt as well.
There are several rules binding this rtt - data-out dialog, specifically
There can be at most outstanding bMaxNumOfRTT such packets. This might
have an effect on write performance (sequential write in particular), as
each data-out upiu must wait for its rtt sibling.
UFSHCI expects bMaxNumOfRTT to be min(bDeviceRTTCap, NORTT). However, as of
today, there does not appear to be no-one who sets it: not the host
controller nor the driver. It wasn't an issue up to now: bMaxNumOfRTT is
set to 2 after manufacturing, and wasn't limiting the write performance.
UFS4.0, and specifically gear 5 changes this, and requires the device to be
more attentive. This doesn't come free - the device has to allocate more
resources to that end, but the sequential write performance improvement is
significant. Early measurements shows 25% gain when moving from rtt 2 to
9. Therefore, set bMaxNumOfRTT to be min(bDeviceRTTCap, NORTT) as UFSHCI
expects.
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
Given the importance of the RTT parameter, we want to be able to configure
it via sysfs. This is because UFS users should be discouraged from change
UFS device parameters without the UFSHCI driver being aware of these
changes.
Signed-off-by: Avri Altman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Bart Van Assche <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
Allow platform vendors to take precedence having their own max rtt support.
This makes sense because the host controller's nortt characteristic may
vary among vendors.
while at it, set this value for Mediatek, as requested by Peter -
https://lore.kernel.org/all/[email protected]/
Signed-off-by: Avri Altman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Peter Wang <[email protected]>
Reviewed-by: Bart Van Assche <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
The rtt-upiu packets precede any data-out upiu packets, thus synchronizing
the data input to the device: this mostly applies to write operations, but
there are other operations that requires rtt as well.
There are several rules binding this rtt - data-out dialog, specifically
There can be at most outstanding bMaxNumOfRTT such packets. This might
have an effect on write performance (sequential write in particular), as
each data-out upiu must wait for its rtt sibling.
UFSHCI expects bMaxNumOfRTT to be min(bDeviceRTTCap, NORTT). However, as of
today, there does not appears to be no-one who sets it: not the host
controller nor the driver. It wasn't an issue up to now: bMaxNumOfRTT is
set to 2 after manufacturing, and wasn't limiting the write performance.
UFS4.0, and specifically gear 5 changes this, and requires the device to be
more attentive. This doesn't come free - the device has to allocate more
resources to that end, but the sequential write performance improvement is
significant. Early measurements shows 25% gain when moving from rtt 2 to
9. Therefore, set bMaxNumOfRTT to be min(bDeviceRTTCap, NORTT) as UFSHCI
expects.
Signed-off-by: Avri Altman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Bean Huo <[email protected]>
Reviewed-by: Bart Van Assche <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
'scsi_dif_tuple' is unused since commit 8cb2049c7448 ("[SCSI] qla2xxx: T10
DIF - Handle uninitalized sectors.").
Remove it.
Signed-off-by: Dr. David Alan Gilbert <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Himanshu Madhani <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
When calling bsg_setup_queue() -> blk_mq_alloc_queue(), we don't pass
the dev as the queuedata, but rather manually set it afterwards. Just
pass dev to blk_mq_alloc_queue() to have automatically set.
Signed-off-by: John Garry <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Christoph Hellwig <[email protected]>
Reviewed-by: Hannes Reinecke <[email protected]>
Tested-by: Himanshu Madhani <[email protected]>
Reviewed-by: Himanshu Madhani <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
When calling scsi_alloc_sdev() -> blk_mq_alloc_queue(), we don't pass
the sdev as the queuedata, but rather manually set it afterwards. Just
pass to blk_mq_alloc_queue() to have automatically set.
Signed-off-by: John Garry <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Christoph Hellwig <[email protected]>
Reviewed-by: Hannes Reinecke <[email protected]>
Tested-by: Himanshu Madhani <[email protected]>
Reviewed-by: Himanshu Madhani <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
Pull in remaining commits from 6.10/scsi-queue.
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
|
|
percpu.h depends on smp.h, but doesn't include it directly because of
circular header dependency issues; percpu.h is needed in a bunch of low
level headers.
This fixes a randconfig build error on mips:
include/linux/alloc_tag.h: In function '__alloc_tag_ref_set':
include/asm-generic/percpu.h:31:40: error: implicit declaration of function 'raw_smp_processor_id' [-Werror=implicit-function-declaration]
Reported-by: kernel test robot <[email protected]>
Fixes: 24e44cc22aa3 ("mm: percpu: enable per-cpu allocation tagging")
Closes: https://lore.kernel.org/oe-kbuild-all/[email protected]/
Signed-off-by: Kent Overstreet <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools
Pull perf tool fix from Arnaldo Carvalho de Melo:
"Revert a patch causing a regression.
This made a simple 'perf record -e cycles:pp make -j199' stop working
on the Ampere ARM64 system Linus uses to test ARM64 kernels".
* tag 'perf-tools-fixes-for-v6.10-1-2024-05-26' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools:
Revert "perf parse-events: Prefer sysfs/JSON hardware events over legacy"
|
|
This reverts commit 617824a7f0f73e4de325cf8add58e55b28c12493.
This made a simple 'perf record -e cycles:pp make -j199' stop working on
the Ampere ARM64 system Linus uses to test ARM64 kernels, as discussed
at length in the threads in the Link tags below.
The fix provided by Ian wasn't acceptable and work to fix this will take
time we don't have at this point, so lets revert this and work on it on
the next devel cycle.
Reported-by: Linus Torvalds <[email protected]>
Cc: Adrian Hunter <[email protected]>
Cc: Bhaskar Chowdhury <[email protected]>
Cc: Ethan Adams <[email protected]>
Cc: Ian Rogers <[email protected]>
Cc: Ingo Molnar <[email protected]>
Cc: James Clark <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Kan Liang <[email protected]>
Cc: Namhyung Kim <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: Thomas Richter <[email protected]>
Cc: Tycho Andersen <[email protected]>
Cc: Yang Jihong <[email protected]>
Link: https://lore.kernel.org/lkml/CAHk-=wi5Ri=yR2jBVk-4HzTzpoAWOgstr1LEvg_-OXtJvXXJOA@mail.gmail.com
Link: https://lore.kernel.org/lkml/CAHk-=wiWvtFyedDNpoV7a8Fq_FpbB+F5KmWK2xPY3QoYseOf_A@mail.gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
|
|
Pull smb client fixes from Steve French:
- two important netfs integration fixes - including for a data
corruption and also fixes for multiple xfstests
- reenable swap support over SMB3
* tag '6.10-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Fix missing set of remote_i_size
cifs: Fix smb3_insert_range() to move the zero_point
cifs: update internal version number
smb3: reenable swapfiles over SMB3 mounts
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"16 hotfixes, 11 of which are cc:stable.
A few nilfs2 fixes, the remainder are for MM: a couple of selftests
fixes, various singletons fixing various issues in various parts"
* tag 'mm-hotfixes-stable-2024-05-25-09-13' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
mm/ksm: fix possible UAF of stable_node
mm/memory-failure: fix handling of dissolved but not taken off from buddy pages
mm: /proc/pid/smaps_rollup: avoid skipping vma after getting mmap_lock again
nilfs2: fix potential hang in nilfs_detach_log_writer()
nilfs2: fix unexpected freezing of nilfs_segctor_sync()
nilfs2: fix use-after-free of timer for log writer thread
selftests/mm: fix build warnings on ppc64
arm64: patching: fix handling of execmem addresses
selftests/mm: compaction_test: fix bogus test success and reduce probability of OOM-killer invocation
selftests/mm: compaction_test: fix incorrect write of zero to nr_hugepages
selftests/mm: compaction_test: fix bogus test success on Aarch64
mailmap: update email address for Satya Priya
mm/huge_memory: don't unpoison huge_zero_folio
kasan, fortify: properly rename memintrinsics
lib: add version into /proc/allocinfo output
mm/vmalloc: fix vmalloc which may return null if called with __GFP_NOFAIL
|