aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2015-01-27Merge branch 'sh_eth'David S. Miller1-21/+59
Ben Hutchings says: ==================== Fixes for sh_eth #3 I'm continuing review and testing of Ethernet support on the R-Car H2 chip. This series fixes the last of the more serious issues I've found. These are not tested on any of the other supported chips. ==================== Signed-off-by: David S. Miller <[email protected]>
2015-01-27sh_eth: Fix DMA-API usage for RX buffersBen Hutchings1-11/+23
- Use the return value of dma_map_single(), rather than calling virt_to_page() separately - Check for mapping failue - Call dma_unmap_single() rather than dma_sync_single_for_cpu() Signed-off-by: Ben Hutchings <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2015-01-27sh_eth: Check for DMA mapping errors on transmitBen Hutchings1-0/+4
dma_map_single() may fail if an IOMMU or swiotlb is in use, so we need to check for this. Signed-off-by: Ben Hutchings <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2015-01-27sh_eth: Ensure DMA engines are stopped before freeing buffersBen Hutchings1-7/+32
Currently we try to clear EDRRR and EDTRR and immediately continue to free buffers. This is unsafe because: - In general, register writes are not serialised with DMA, so we still have to wait for DMA to complete somehow - The R8A7790 (R-Car H2) manual states that the TX running flag cannot be cleared by writing to EDTRR - The same manual states that clearing the RX running flag only stops RX DMA at the next packet boundary I applied this patch to the driver to detect DMA writes to freed buffers: > --- a/drivers/net/ethernet/renesas/sh_eth.c > +++ b/drivers/net/ethernet/renesas/sh_eth.c > @@ -1098,7 +1098,14 @@ static void sh_eth_ring_free(struct net_device *ndev) > /* Free Rx skb ringbuffer */ > if (mdp->rx_skbuff) { > for (i = 0; i < mdp->num_rx_ring; i++) > + memcpy(mdp->rx_skbuff[i]->data, > + "Hello, world", 12); > + msleep(100); > + for (i = 0; i < mdp->num_rx_ring; i++) { > + WARN_ON(memcmp(mdp->rx_skbuff[i]->data, > + "Hello, world", 12)); > dev_kfree_skb(mdp->rx_skbuff[i]); > + } > } > kfree(mdp->rx_skbuff); > mdp->rx_skbuff = NULL; then ran the loop: while ethtool -G eth0 rx 128 ; ethtool -G eth0 rx 64; do echo -n .; done and 'ping -f' toward the sh_eth port from another machine. The warning fired several times a minute. To fix these issues: - Deactivate all TX descriptors rather than writing to EDTRR - As there seems to be no way of telling when RX DMA is stopped, perform a soft reset to ensure that both DMA enginess are stopped - To reduce the possibility of the reset truncating a transmitted frame, disable egress and wait a reasonable time to reach a packet boundary before resetting - Update statistics before resetting (The 'reasonable time' does not allow for CS/CD in half-duplex mode, but half-duplex no longer seems reasonable!) Signed-off-by: Ben Hutchings <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2015-01-27sh_eth: Remove RX overflow log messagesBen Hutchings1-3/+0
If RX traffic is overflowing the FIFO or DMA ring, logging every time this happens just makes things worse. These errors are visible in the statistics anyway. Signed-off-by: Ben Hutchings <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2015-01-27Merge tag 'linux-can-fixes-for-3.19-20150127' of ↵David S. Miller1-13/+15
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can Marc Kleine-Budde says: ==================== pull-request: can 2015-01-27 this is another pull request for net/master which consists of 4 patches. All 4 patches are contributed by Ahmed S. Darwish, he fixes more problems in the kvaser_usb driver. David, please merge net/master to net-next/master, as we have more kvaser_usb patches in the queue, that target net-next. ==================== Signed-off-by: David S. Miller <[email protected]>
2015-01-27ping: Fix race in free in receive path[email protected]1-1/+4
An exception is seen in ICMP ping receive path where the skb destructor sock_rfree() tries to access a freed socket. This happens because ping_rcv() releases socket reference with sock_put() and this internally frees up the socket. Later icmp_rcv() will try to free the skb and as part of this, skb destructor is called and which leads to a kernel panic as the socket is freed already in ping_rcv(). -->|exception -007|sk_mem_uncharge -007|sock_rfree -008|skb_release_head_state -009|skb_release_all -009|__kfree_skb -010|kfree_skb -011|icmp_rcv -012|ip_local_deliver_finish Fix this incorrect free by cloning this skb and processing this cloned skb instead. This patch was suggested by Eric Dumazet Signed-off-by: Subash Abhinov Kasiviswanathan <[email protected]> Cc: Eric Dumazet <[email protected]> Signed-off-by: Eric Dumazet <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2015-01-27udp_diag: Fix socket skipping within chainHerbert Xu1-1/+3
While working on rhashtable walking I noticed that the UDP diag dumping code is buggy. In particular, the socket skipping within a chain never happens, even though we record the number of sockets that should be skipped. As this code was supposedly copied from TCP, this patch does what TCP does and resets num before we walk a chain. Signed-off-by: Herbert Xu <[email protected]> Acked-by: Pavel Emelyanov <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2015-01-27can: kvaser_usb: Fix state handling upon BUS_ERROR eventsAhmed S. Darwish1-4/+3
While being in an ERROR_WARNING state, and receiving further bus error events with error counters still in the ERROR_WARNING range of 97-127 inclusive, the state handling code erroneously reverts back to ERROR_ACTIVE. Per the CAN standard, only revert to ERROR_ACTIVE when the error counters are less than 96. Moreover, in certain Kvaser models, the BUS_ERROR flag is always set along with undefined bits in the M16C status register. Thus use bitwise operators instead of full equality for checking that register against bus errors. Signed-off-by: Ahmed S. Darwish <[email protected]> Cc: linux-stable <[email protected]> Signed-off-by: Marc Kleine-Budde <[email protected]>
2015-01-27can: kvaser_usb: Retry the first bulk transfer on -ETIMEDOUTAhmed S. Darwish1-2/+10
On some x86 laptops, plugging a Kvaser device again after an unplug makes the firmware always ignore the very first command. For such a case, provide some room for retries instead of completely exiting the driver init code. Signed-off-by: Ahmed S. Darwish <[email protected]> Cc: linux-stable <[email protected]> Signed-off-by: Marc Kleine-Budde <[email protected]>
2015-01-27can: kvaser_usb: Send correct context to URB completionAhmed S. Darwish1-1/+1
Send expected argument to the URB completion hander: a CAN netdevice instead of the network interface private context `kvaser_usb_net_priv'. This was discovered by having some garbage in the kernel log in place of the netdevice names: can0 and can1. Signed-off-by: Ahmed S. Darwish <[email protected]> Cc: linux-stable <[email protected]> Signed-off-by: Marc Kleine-Budde <[email protected]>
2015-01-27can: kvaser_usb: Do not sleep in atomic contextAhmed S. Darwish1-6/+1
Upon receiving a hardware event with the BUS_RESET flag set, the driver kills all of its anchored URBs and resets all of its transmit URB contexts. Unfortunately it does so under the context of URB completion handler `kvaser_usb_read_bulk_callback()', which is often called in an atomic context. While the device is flooded with many received error packets, usb_kill_urb() typically sleeps/reschedules till the transfer request of each killed URB in question completes, leading to the sleep in atomic bug. [3] In v2 submission of the original driver patch [1], it was stated that the URBs kill and tx contexts reset was needed since we don't receive any tx acknowledgments later and thus such resources will be locked down forever. Fortunately this is no longer needed since an earlier bugfix in this patch series is now applied: all tx URB contexts are reset upon CAN channel close. [2] Moreover, a BUS_RESET is now treated _exactly_ like a BUS_OFF event, which is the recommended handling method advised by the device manufacturer. [1] http://article.gmane.org/gmane.linux.network/239442 http://www.webcitation.org/6Vr2yagAQ [2] can: kvaser_usb: Reset all URB tx contexts upon channel close 889b77f7fd2bcc922493d73a4c51d8a851505815 [3] Stacktrace: <IRQ> [<ffffffff8158de87>] dump_stack+0x45/0x57 [<ffffffff8158b60c>] __schedule_bug+0x41/0x4f [<ffffffff815904b1>] __schedule+0x5f1/0x700 [<ffffffff8159360a>] ? _raw_spin_unlock_irqrestore+0xa/0x10 [<ffffffff81590684>] schedule+0x24/0x70 [<ffffffff8147d0a5>] usb_kill_urb+0x65/0xa0 [<ffffffff81077970>] ? prepare_to_wait_event+0x110/0x110 [<ffffffff8147d7d8>] usb_kill_anchored_urbs+0x48/0x80 [<ffffffffa01f4028>] kvaser_usb_unlink_tx_urbs+0x18/0x50 [kvaser_usb] [<ffffffffa01f45d0>] kvaser_usb_rx_error+0xc0/0x400 [kvaser_usb] [<ffffffff8108b14a>] ? vprintk_default+0x1a/0x20 [<ffffffffa01f5241>] kvaser_usb_read_bulk_callback+0x4c1/0x5f0 [kvaser_usb] [<ffffffff8147a73e>] __usb_hcd_giveback_urb+0x5e/0xc0 [<ffffffff8147a8a1>] usb_hcd_giveback_urb+0x41/0x110 [<ffffffffa0008748>] finish_urb+0x98/0x180 [ohci_hcd] [<ffffffff810cd1a7>] ? acct_account_cputime+0x17/0x20 [<ffffffff81069f65>] ? local_clock+0x15/0x30 [<ffffffffa000a36b>] ohci_work+0x1fb/0x5a0 [ohci_hcd] [<ffffffff814fbb31>] ? process_backlog+0xb1/0x130 [<ffffffffa000cd5b>] ohci_irq+0xeb/0x270 [ohci_hcd] [<ffffffff81479fc1>] usb_hcd_irq+0x21/0x30 [<ffffffff8108bfd3>] handle_irq_event_percpu+0x43/0x120 [<ffffffff8108c0ed>] handle_irq_event+0x3d/0x60 [<ffffffff8108ec84>] handle_fasteoi_irq+0x74/0x110 [<ffffffff81004dfd>] handle_irq+0x1d/0x30 [<ffffffff81004727>] do_IRQ+0x57/0x100 [<ffffffff8159482a>] common_interrupt+0x6a/0x6a Signed-off-by: Ahmed S. Darwish <[email protected]> Cc: linux-stable <[email protected]> Signed-off-by: Marc Kleine-Budde <[email protected]>
2015-01-26Merge tag 'mac80211-for-davem-2015-01-23' of ↵David S. Miller4-20/+26
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211 Another set of last-minute fixes: * fix station double-removal when suspending while associating * fix the HT (802.11n) header length calculation * fix the CCK radiotap flag used for monitoring, a pretty old regression but a simple one-liner * fix per-station group-key handling Signed-off-by: David S. Miller <[email protected]>
2015-01-26ipv4: try to cache dst_entries which would cause a redirectHannes Frederic Sowa3-10/+13
Not caching dst_entries which cause redirects could be exploited by hosts on the same subnet, causing a severe DoS attack. This effect aggravated since commit f88649721268999 ("ipv4: fix dst race in sk_dst_get()"). Lookups causing redirects will be allocated with DST_NOCACHE set which will force dst_release to free them via RCU. Unfortunately waiting for RCU grace period just takes too long, we can end up with >1M dst_entries waiting to be released and the system will run OOM. rcuos threads cannot catch up under high softirq load. Attaching the flag to emit a redirect later on to the specific skb allows us to cache those dst_entries thus reducing the pressure on allocation and deallocation. This issue was discovered by Marcelo Leitner. Cc: Julian Anastasov <[email protected]> Signed-off-by: Marcelo Leitner <[email protected]> Signed-off-by: Florian Westphal <[email protected]> Signed-off-by: Hannes Frederic Sowa <[email protected]> Signed-off-by: Julian Anastasov <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2015-01-26Merge branch 'bpf'David S. Miller2-10/+19
Alexei Starovoitov says: ==================== bpf: fix two bugs Michael Holzheu caught two issues (in bpf syscall and in the test). Fix them. Details in corresponding patches. ==================== Signed-off-by: David S. Miller <[email protected]>
2015-01-26samples: bpf: relax test_maps checkAlexei Starovoitov1-2/+2
hash map is unordered, so get_next_key() iterator shouldn't rely on particular order of elements. So relax this test. Fixes: ffb65f27a155 ("bpf: add a testsuite for eBPF maps") Reported-by: Michael Holzheu <[email protected]> Signed-off-by: Alexei Starovoitov <[email protected]> Acked-by: Daniel Borkmann <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2015-01-26bpf: rcu lock must not be held when calling copy_to_user()Alexei Starovoitov1-8/+17
BUG: sleeping function called from invalid context at mm/memory.c:3732 in_atomic(): 0, irqs_disabled(): 0, pid: 671, name: test_maps 1 lock held by test_maps/671: #0: (rcu_read_lock){......}, at: [<0000000000264190>] map_lookup_elem+0xe8/0x260 Call Trace: ([<0000000000115b7e>] show_trace+0x12e/0x150) [<0000000000115c40>] show_stack+0xa0/0x100 [<00000000009b163c>] dump_stack+0x74/0xc8 [<000000000017424a>] ___might_sleep+0x23a/0x248 [<00000000002b58e8>] might_fault+0x70/0xe8 [<0000000000264230>] map_lookup_elem+0x188/0x260 [<0000000000264716>] SyS_bpf+0x20e/0x840 Fix it by allocating temporary buffer to store map element value. Fixes: db20fd2b0108 ("bpf: add lookup/update/delete/iterate methods to BPF maps") Reported-by: Michael Holzheu <[email protected]> Signed-off-by: Alexei Starovoitov <[email protected]> Acked-by: Daniel Borkmann <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2015-01-26net: sctp: fix slab corruption from use after free on INIT collisionsDaniel Borkmann1-1/+0
When hitting an INIT collision case during the 4WHS with AUTH enabled, as already described in detail in commit 1be9a950c646 ("net: sctp: inherit auth_capable on INIT collisions"), it can happen that we occasionally still remotely trigger the following panic on server side which seems to have been uncovered after the fix from commit 1be9a950c646 ... [ 533.876389] BUG: unable to handle kernel paging request at 00000000ffffffff [ 533.913657] IP: [<ffffffff811ac385>] __kmalloc+0x95/0x230 [ 533.940559] PGD 5030f2067 PUD 0 [ 533.957104] Oops: 0000 [#1] SMP [ 533.974283] Modules linked in: sctp mlx4_en [...] [ 534.939704] Call Trace: [ 534.951833] [<ffffffff81294e30>] ? crypto_init_shash_ops+0x60/0xf0 [ 534.984213] [<ffffffff81294e30>] crypto_init_shash_ops+0x60/0xf0 [ 535.015025] [<ffffffff8128c8ed>] __crypto_alloc_tfm+0x6d/0x170 [ 535.045661] [<ffffffff8128d12c>] crypto_alloc_base+0x4c/0xb0 [ 535.074593] [<ffffffff8160bd42>] ? _raw_spin_lock_bh+0x12/0x50 [ 535.105239] [<ffffffffa0418c11>] sctp_inet_listen+0x161/0x1e0 [sctp] [ 535.138606] [<ffffffff814e43bd>] SyS_listen+0x9d/0xb0 [ 535.166848] [<ffffffff816149a9>] system_call_fastpath+0x16/0x1b ... or depending on the the application, for example this one: [ 1370.026490] BUG: unable to handle kernel paging request at 00000000ffffffff [ 1370.026506] IP: [<ffffffff811ab455>] kmem_cache_alloc+0x75/0x1d0 [ 1370.054568] PGD 633c94067 PUD 0 [ 1370.070446] Oops: 0000 [#1] SMP [ 1370.085010] Modules linked in: sctp kvm_amd kvm [...] [ 1370.963431] Call Trace: [ 1370.974632] [<ffffffff8120f7cf>] ? SyS_epoll_ctl+0x53f/0x960 [ 1371.000863] [<ffffffff8120f7cf>] SyS_epoll_ctl+0x53f/0x960 [ 1371.027154] [<ffffffff812100d3>] ? anon_inode_getfile+0xd3/0x170 [ 1371.054679] [<ffffffff811e3d67>] ? __alloc_fd+0xa7/0x130 [ 1371.080183] [<ffffffff816149a9>] system_call_fastpath+0x16/0x1b With slab debugging enabled, we can see that the poison has been overwritten: [ 669.826368] BUG kmalloc-128 (Tainted: G W ): Poison overwritten [ 669.826385] INFO: 0xffff880228b32e50-0xffff880228b32e50. First byte 0x6a instead of 0x6b [ 669.826414] INFO: Allocated in sctp_auth_create_key+0x23/0x50 [sctp] age=3 cpu=0 pid=18494 [ 669.826424] __slab_alloc+0x4bf/0x566 [ 669.826433] __kmalloc+0x280/0x310 [ 669.826453] sctp_auth_create_key+0x23/0x50 [sctp] [ 669.826471] sctp_auth_asoc_create_secret+0xcb/0x1e0 [sctp] [ 669.826488] sctp_auth_asoc_init_active_key+0x68/0xa0 [sctp] [ 669.826505] sctp_do_sm+0x29d/0x17c0 [sctp] [...] [ 669.826629] INFO: Freed in kzfree+0x31/0x40 age=1 cpu=0 pid=18494 [ 669.826635] __slab_free+0x39/0x2a8 [ 669.826643] kfree+0x1d6/0x230 [ 669.826650] kzfree+0x31/0x40 [ 669.826666] sctp_auth_key_put+0x19/0x20 [sctp] [ 669.826681] sctp_assoc_update+0x1ee/0x2d0 [sctp] [ 669.826695] sctp_do_sm+0x674/0x17c0 [sctp] Since this only triggers in some collision-cases with AUTH, the problem at heart is that sctp_auth_key_put() on asoc->asoc_shared_key is called twice when having refcnt 1, once directly in sctp_assoc_update() and yet again from within sctp_auth_asoc_init_active_key() via sctp_assoc_update() on the already kzfree'd memory, which is also consistent with the observation of the poison decrease from 0x6b to 0x6a (note: the overwrite is detected at a later point in time when poison is checked on new allocation). Reference counting of auth keys revisited: Shared keys for AUTH chunks are being stored in endpoints and associations in endpoint_shared_keys list. On endpoint creation, a null key is being added; on association creation, all endpoint shared keys are being cached and thus cloned over to the association. struct sctp_shared_key only holds a pointer to the actual key bytes, that is, struct sctp_auth_bytes which keeps track of users internally through refcounting. Naturally, on assoc or enpoint destruction, sctp_shared_key are being destroyed directly and the reference on sctp_auth_bytes dropped. User space can add keys to either list via setsockopt(2) through struct sctp_authkey and by passing that to sctp_auth_set_key() which replaces or adds a new auth key. There, sctp_auth_create_key() creates a new sctp_auth_bytes with refcount 1 and in case of replacement drops the reference on the old sctp_auth_bytes. A key can be set active from user space through setsockopt() on the id via sctp_auth_set_active_key(), which iterates through either endpoint_shared_keys and in case of an assoc, invokes (one of various places) sctp_auth_asoc_init_active_key(). sctp_auth_asoc_init_active_key() computes the actual secret from local's and peer's random, hmac and shared key parameters and returns a new key directly as sctp_auth_bytes, that is asoc->asoc_shared_key, plus drops the reference if there was a previous one. The secret, which where we eventually double drop the ref comes from sctp_auth_asoc_set_secret() with intitial refcount of 1, which also stays unchanged eventually in sctp_assoc_update(). This key is later being used for crypto layer to set the key for the hash in crypto_hash_setkey() from sctp_auth_calculate_hmac(). To close the loop: asoc->asoc_shared_key is freshly allocated secret material and independant of the sctp_shared_key management keeping track of only shared keys in endpoints and assocs. Hence, also commit 4184b2a79a76 ("net: sctp: fix memory leak in auth key management") is independant of this bug here since it concerns a different layer (though same structures being used eventually). asoc->asoc_shared_key is reference dropped correctly on assoc destruction in sctp_association_free() and when active keys are being replaced in sctp_auth_asoc_init_active_key(), it always has a refcount of 1. Hence, it's freed prematurely in sctp_assoc_update(). Simple fix is to remove that sctp_auth_key_put() from there which fixes these panics. Fixes: 730fc3d05cd4 ("[SCTP]: Implete SCTP-AUTH parameter processing") Signed-off-by: Daniel Borkmann <[email protected]> Acked-by: Vlad Yasevich <[email protected]> Acked-by: Neil Horman <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2015-01-26net: mv643xx_eth: Fix highmem support in non-TSO egress pathEzequiel Garcia1-10/+49
Commit 69ad0dd7af22b61d9e0e68e56b6290121618b0fb Author: Ezequiel Garcia <[email protected]> Date: Mon May 19 13:59:59 2014 -0300 net: mv643xx_eth: Use dma_map_single() to map the skb fragments caused a nasty regression by removing the support for highmem skb fragments. By using page_address() to get the address of a fragment's page, we are assuming a lowmem page. However, such assumption is incorrect, as fragments can be in highmem pages, resulting in very nasty issues. This commit fixes this by using the skb_frag_dma_map() helper, which takes care of mapping the skb fragment properly. Additionally, the type of mapping is now tracked, so it can be unmapped using dma_unmap_page or dma_unmap_single when appropriate. This commit also fixes the error path in txq_init() to release the resources properly. Fixes: 69ad0dd7af22 ("net: mv643xx_eth: Use dma_map_single() to map the skb fragments") Reported-by: Russell King <[email protected]> Signed-off-by: Ezequiel Garcia <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2015-01-26Merge branch 'sh_eth'David S. Miller2-30/+55
Ben Hutchings says: ==================== Fixes for sh_eth #2 I'm continuing review and testing of Ethernet support on the R-Car H2 chip. This series fixes more of the issues I've found, but it won't be the last set. These are not tested on any of the other supported chips. ==================== Signed-off-by: David S. Miller <[email protected]>
2015-01-26sh_eth: Fix serialisation of interrupt disable with interrupt & NAPI handlersBen Hutchings2-9/+31
In order to stop the RX path accessing the RX ring while it's being stopped or resized, we clear the interrupt mask (EESIPR) and then call free_irq() or synchronise_irq(). This is insufficient because the interrupt handler or NAPI poller may set EESIPR again after we clear it. Also, in sh_eth_set_ringparam() we currently don't disable NAPI polling at all. I could easily trigger a crash by running the loop: while ethtool -G eth0 rx 128 && ethtool -G eth0 rx 64; do echo -n .; done and 'ping -f' toward the sh_eth port from another machine. To fix this: - Add a software flag (irq_enabled) to signal whether interrupts should be enabled - In the interrupt handler, if the flag is clear then clear EESIPR and return - In the NAPI poller, if the flag is clear then don't set EESIPR - Set the flag before enabling interrupts in sh_eth_dev_init() and sh_eth_set_ringparam() - Clear the flag and serialise with the interrupt and NAPI handlers before clearing EESIPR in sh_eth_close() and sh_eth_set_ringparam() After this, I could run the loop for 100,000 iterations successfully. Signed-off-by: Ben Hutchings <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2015-01-26sh_eth: Fix crash or memory leak when resizing rings on device that is downBen Hutchings1-16/+18
If the device is down then no packet buffers should be allocated. We also must not touch its registers as it may be powered off. Signed-off-by: Ben Hutchings <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2015-01-26sh_eth: Detach net device when stopping queue to resize DMA ringsBen Hutchings1-1/+2
We must only ever stop TX queues when they are full or the net device is not 'ready' so far as the net core, and specifically the watchdog, is concerned. Otherwise, the watchdog may fire *immediately* if no packets have been added to the queue in the last 5 seconds. What's more, sh_eth_tx_timeout() will likely crash if called while we're resizing the TX ring. I could easily trigger this by running the loop: while ethtool -G eth0 rx 128 && ethtool -G eth0 rx 64; do echo -n .; done Signed-off-by: Ben Hutchings <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2015-01-26sh_eth: Fix padding of short frames on TXBen Hutchings1-4/+4
If an skb to be transmitted is shorter than the minimum Ethernet frame length, we currently set the DMA descriptor length to the minimum but do not add zero-padding. This could result in leaking sensitive data. We also pass different lengths to dma_map_single() and dma_unmap_single(). Use skb_padto() to pad properly, before calling dma_map_single(). Signed-off-by: Ben Hutchings <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2015-01-26drivers: net: cpsw: discard dual emac default vlan configurationMugunthan V N1-0/+22
In Dual EMAC, the default VLANs are used to segregate Rx packets between the ports, so adding the same default VLAN to the switch will affect the normal packet transfers. So returning error on addition of dual EMAC default VLANs. Even if EMAC 0 default port VLAN is added to EMAC 1, it will lead to break dual EMAC port separations. Fixes: d9ba8f9e6298 (driver: net: ethernet: cpsw: dual emac interface implementation) Cc: <[email protected]> # v3.9+ Reported-by: Felipe Balbi <[email protected]> Signed-off-by: Mugunthan V N <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2015-01-26Merge branch 'cls_bpf'David S. Miller1-2/+13
Daniel Borkmann says: ==================== Two cls_bpf fixes Found them while doing a review on act_bpf and going over the cls_bpf code again. Will also address the first issue in act_bpf as it needs to be fixed there, too. ==================== Signed-off-by: David S. Miller <[email protected]>
2015-01-26net: cls_bpf: fix auto generation of per list handlesDaniel Borkmann1-2/+8
When creating a bpf classifier in tc with priority collisions and invoking automatic unique handle assignment, cls_bpf_grab_new_handle() will return a wrong handle id which in fact is non-unique. Usually altering of specific filters is being addressed over major id, but in case of collisions we result in a filter chain, where handle ids address individual cls_bpf_progs inside the classifier. Issue is, in cls_bpf_grab_new_handle() we probe for head->hgen handle in cls_bpf_get() and in case we found a free handle, we're supposed to use exactly head->hgen. In case of insufficient numbers of handles, we bail out later as handle id 0 is not allowed. Fixes: 7d1d65cb84e1 ("net: sched: cls_bpf: add BPF-based classifier") Signed-off-by: Daniel Borkmann <[email protected]> Acked-by: Jiri Pirko <[email protected]> Acked-by: Alexei Starovoitov <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2015-01-26net: cls_bpf: fix size mismatch on filter preparationDaniel Borkmann1-0/+5
In cls_bpf_modify_existing(), we read out the number of filter blocks, do some sanity checks, allocate a block on that size, and copy over the BPF instruction blob from user space, then pass everything through the classic BPF checker prior to installation of the classifier. We should reject mismatches here, there are 2 scenarios: the number of filter blocks could be smaller than the provided instruction blob, so we do a partial copy of the BPF program, and thus the instructions will either be rejected from the verifier or a valid BPF program will be run; in the other case, we'll end up copying more than we're supposed to, and most likely the trailing garbage will be rejected by the verifier as well (i.e. we need to fit instruction pattern, ret {A,K} needs to be last instruction, load/stores must be correct, etc); in case not, we would leak memory when dumping back instruction patterns. The code should have only used nla_len() as Dave noted to avoid this from the beginning. Anyway, lets fix it by rejecting such load attempts. Fixes: 7d1d65cb84e1 ("net: sched: cls_bpf: add BPF-based classifier") Signed-off-by: Daniel Borkmann <[email protected]> Acked-by: Jiri Pirko <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2015-01-26Merge tag 'linux-can-fixes-for-3.19-20150121' of ↵David S. Miller1-0/+3
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can Marc Kleine-Budde says: ==================== pull-request: can 2015-01-21 this is a pull request for v3.19, net/master, which consists of a single patch. Viktor Babrian fixes the issue in the c_can dirver, that the CAN interface might continue to send frames after the interface has been shut down. ==================== Signed-off-by: David S. Miller <[email protected]>
2015-01-25Merge branch 's390'David S. Miller3-139/+248
Ursula Braun says: ==================== s390/qeth patches for net here are two s390/qeth patches built for net. One patch is quite large, but we would like to fix the locking warning seen in recent kernels as soon as possible. But if you want me to submit these patches for net-next, I will do. Or Gerlitz says: ==================== Signed-off-by: David S. Miller <[email protected]>
2015-01-25390/qeth: Fix locking warning during qeth device setupThomas Richter3-34/+132
Do not wait for channel command buffers in IPA commands. The potential wait could be done while holding a spin lock and causes in recent kernels such a bug if kernel lock debugging is enabled: kernel: BUG: sleeping function called from invalid context at drivers/s390/net/qeth_core_main.c: 794 kernel: in_atomic(): 1, irqs_disabled(): 0, pid: 2031, name: NetworkManager kernel: 2 locks held by NetworkManager/2031: kernel: #0: (rtnl_mutex){+.+.+.}, at: [<00000000006e0d7a>] rtnetlink_rcv+0x32/0x50 kernel: #1: (_xmit_ETHER){+.....}, at: [<00000000006cfe90>] dev_set_rx_mode+0x30/0x50 kernel: CPU: 0 PID: 2031 Comm: NetworkManager Not tainted 3.18.0-rc5-next-20141124 #1 kernel: 00000000275fb1f0 00000000275fb280 0000000000000002 0000000000000000 00000000275fb320 00000000275fb298 00000000275fb298 00000000007e326a 0000000000000000 000000000099ce2c 00000000009b4988 000000000000000b 00000000275fb2e0 00000000275fb280 0000000000000000 0000000000000000 0000000000000000 00000000001129c8 00000000275fb280 00000000275fb2e0 kernel: Call Trace: kernel: ([<00000000001128b0>] show_trace+0xf8/0x158) kernel: [<000000000011297a>] show_stack+0x6a/0xe8 kernel: [<00000000007e995a>] dump_stack+0x82/0xb0 kernel: [<000000000017d668>] ___might_sleep+0x170/0x228 kernel: [<000003ff80026f0e>] qeth_wait_for_buffer+0x36/0xd0 [qeth] kernel: [<000003ff80026fe2>] qeth_get_ipacmd_buffer+0x3a/0xc0 [qeth] kernel: [<000003ff80105078>] qeth_l3_send_setdelmc+0x58/0xf8 [qeth_l3] kernel: [<000003ff8010b1fe>] qeth_l3_set_ip_addr_list+0x2c6/0x848 [qeth_l3] kernel: [<000003ff8010bbb4>] qeth_l3_set_multicast_list+0x434/0xc48 [qeth_l3] kernel: [<00000000006cfe9a>] dev_set_rx_mode+0x3a/0x50 kernel: [<00000000006cff90>] __dev_open+0xe0/0x140 kernel: [<00000000006d02a0>] __dev_change_flags+0xa0/0x178 kernel: [<00000000006d03a8>] dev_change_flags+0x30/0x70 kernel: [<00000000006e14ee>] do_setlink+0x346/0x9a0 ... The device driver has plenty of command buffers available per channel for channel command communication. In the extremely rare case when there is no command buffer available, return a NULL pointer and issue a warning in the kernel log. The caller handles the case when a NULL pointer is encountered and returns an error. In the case the wait for command buffer is possible (because no lock is held as in the OSN case), still wait until a channel command buffer is available. Signed-off-by: Thomas Richter <[email protected]> Signed-off-by: Ursula Braun <[email protected]> Reviewed-by: Eugene Crosser <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2015-01-25qeth: clean up error handlingEugene Crosser2-106/+117
In the functions that are registering and unregistering MAC addresses in the qeth-handled hardware, remove callback functions that are unnesessary, as only the return code is analyzed. Translate hardware response codes to semi-standard 'errno'-like codes for readability. Add kernel-doc description to the internal API function qeth_send_control_data(). Signed-off-by: Eugene Crosser <[email protected]> Signed-off-by: Ursula Braun <[email protected]> Reviewed-by: Thomas-Mich Richter <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2015-01-25ipv6: Fix __ip6_route_redirectMartin KaFai Lau1-1/+5
In my last commit (a3c00e4: ipv6: Remove BACKTRACK macro), the changes in __ip6_route_redirect is incorrect. The following case is missed: 1. The for loop tries to find a valid gateway rt. If it fails to find one, rt will be NULL. 2. When rt is NULL, it is set to the ip6_null_entry. 3. The newly added 'else if', from a3c00e4, will stop the backtrack from happening. Signed-off-by: Martin KaFai Lau <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2015-01-25net: dsa: set slave MII bus PHY maskVivien Didelot1-0/+1
When registering a mdio bus, Linux assumes than every port has a PHY and tries to scan it. If a switch port has no PHY registered, DSA will fail to register the slave MII bus. To fix this, set the slave MII bus PHY mask to the switch PHYs mask. As an example, if we use a Marvell MV88E6352 (which is a 7-port switch with no registered PHYs for port 5 and port 6), with the following declared names: static struct dsa_chip_data switch_cdata = { [...] .port_names[0] = "sw0", .port_names[1] = "sw1", .port_names[2] = "sw2", .port_names[3] = "sw3", .port_names[4] = "sw4", .port_names[5] = "cpu", }; DSA will fail to create the switch instance. With the PHY mask set for the slave MII bus, only the PHY for ports 0-4 will be scanned and the instance will be successfully created. Signed-off-by: Vivien Didelot <[email protected]> Tested-by: Florian Fainelli <[email protected]> Acked-by: Florian Fainelli <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2015-01-25ipvlan: fix incorrect usage of IS_ERR() macro in IPv6 code path.Mahesh Bandewar1-2/+4
The ip6_route_output() always returns a valid dst pointer unlike in IPv4 case. So the validation has to be different from the IPv4 path. Correcting that error in this patch. This was picked up by a static checker with a following warning - drivers/net/ipvlan/ipvlan_core.c:380 ipvlan_process_v6_outbound() warn: 'dst' isn't an ERR_PTR Signed-off-by: Mahesh Bandewar <[email protected]> Reported-by: Dan Carpenter <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2015-01-25net: llc: use correct size for sysctl timeout entriesSasha Levin1-4/+4
The timeout entries are sizeof(int) rather than sizeof(long), which means that when they were getting read we'd also leak kernel memory to userspace along with the timeout values. Signed-off-by: Sasha Levin <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2015-01-25netxen: fix netxen_nic_poll() logicEric Dumazet1-1/+4
NAPI poll logic now enforces that a poller returns exactly the budget when it wants to be called again. If a driver limits TX completion, it has to return budget as well when the limit is hit, not the number of received packets. Reported-and-tested-by: Mike Galbraith <[email protected]> Signed-off-by: Eric Dumazet <[email protected]> Fixes: d75b1ade567f ("net: less interrupt masking in NAPI") Cc: Manish Chopra <[email protected]> Acked-by: Manish Chopra <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2015-01-24enic: fix rx napi poll return valueGovindarajulu Varadarajan1-1/+1
With the commit d75b1ade567ffab ("net: less interrupt masking in NAPI") napi repoll is done only when work_done == budget. When we are in busy_poll we return 0 in napi_poll. We should return budget. Signed-off-by: Govindarajulu Varadarajan <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2015-01-24Merge tag 'wireless-drivers-for-davem-2015-01-20' of ↵David S. Miller6-31/+69
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers ath9k: * fix an IRQ storm caused by commit 872b5d814f99 iwlwifi: * A fix for scan that fixes a firmware assertion * A fix that improves roaming behavior. Same fix has been tested for a while in iwldvm. This is a bit of a work around, but the real fix should be in mac80211 and will come later. * A fix for BARs that avoids a WARNING. * one fix for rfkill while scheduled scan is running. Linus's system hit this issue. WiFi would be unavailable after this has happpened because of bad state in cfg80211. Signed-off-by: David S. Miller <[email protected]>
2015-01-24ARM: dts: imx6sx: correct i.MX6sx sdb board enet phy addressNimrod Andy1-4/+4
The commit (3d125f9c91c5) cause i.MX6SX sdb enet cannot work. The cause is the commit add mdio node with un-correct phy address. The patch just correct i.MX6sx sdb board enet phy address. V2: * As Shawn's suggestion that unit-address should match 'reg' property, so update ethernet-phy unit-address. Acked-by: Stefan Agner <[email protected]> Signed-off-by: Fugang Duan <[email protected]> Acked-by: Shawn Guo <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2015-01-23amd-xgbe: Use proper Rx flow control registerLendacky, Thomas2-6/+7
Updated hardware documention shows the Rx flow control settings were moved from the Rx queue operation mode register to a new Rx queue flow control register. The old flow control settings are now reserved areas of the Rx queue operation mode register. Update the code to use the new register. Signed-off-by: Tom Lendacky <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2015-01-23nl80211: fix per-station group key get/del and memory leakJohannes Berg1-5/+4
In case userspace attempts to obtain key information for or delete a unicast key, this is currently erroneously rejected unless the driver sets the WIPHY_FLAG_IBSS_RSN flag. Apparently enough drivers do so it was never noticed. Fix that, and while at it fix a potential memory leak: the error path in the get_key() function was placed after allocating a message but didn't free it - move it to a better place. Luckily admin permissions are needed to call this operation. Cc: [email protected] Fixes: e31b82136d1ad ("cfg80211/mac80211: allow per-station GTKs") Signed-off-by: Johannes Berg <[email protected]>
2015-01-23mac80211: properly set CCK flag in radiotapMathy Vanhoef1-1/+1
Fix a regression introduced by commit a5e70697d0c4 ("mac80211: add radiotap flag and handling for 5/10 MHz") where the IEEE80211_CHAN_CCK channel type flag was incorrectly replaced by the IEEE80211_CHAN_OFDM flag. This commit fixes that by using the CCK flag again. Cc: [email protected] Fixes: a5e70697d0c4 ("mac80211: add radiotap flag and handling for 5/10 MHz") Signed-off-by: Mathy Vanhoef <[email protected]> Signed-off-by: Johannes Berg <[email protected]>
2015-01-23mac80211: correct header length calculationFred Chou1-0/+6
HT Control field may also be present in management frames, as defined in 8.2.4.1.10 of 802.11-2012. Account for this in calculation of header length. Signed-off-by: Fred Chou <[email protected]> Signed-off-by: Johannes Berg <[email protected]>
2015-01-23mac80211: only roll back station states for WDS when suspendingLuciano Coelho1-14/+15
In normal cases (i.e. when we are fully associated), cfg80211 takes care of removing all the stations before calling suspend in mac80211. But in the corner case when we suspend during authentication or association, mac80211 needs to roll back the station states. But we shouldn't roll back the station states in the suspend function, because this is taken care of in other parts of the code, except for WDS interfaces. For AP types of interfaces, cfg80211 takes care of disconnecting all stations before calling the driver's suspend code. For station interfaces, this is done in the quiesce code. For WDS interfaces we still need to do it here, so move the code into a new switch case for WDS. Cc: [email protected] [3.15+] Signed-off-by: Luciano Coelho <[email protected]> Signed-off-by: Johannes Berg <[email protected]>
2015-01-21can: c_can: end pending transmission on network stop (ifdown)Viktor Babrian1-0/+3
Put controller into init mode in network stop to end pending transmissions. The issue is observed in cases when transmitted frame is not acked. Signed-off-by: Viktor Babrian <[email protected]> Cc: linux-stable <[email protected]> Signed-off-by: Marc Kleine-Budde <[email protected]>
2015-01-20Merge tag 'pinctrl-v3.19-3' of ↵Linus Torvalds5-31/+26
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl Pull pin control fixes from Linus Walleij: "Here is a (hopefully final) slew of pin control fixes for the v3.19 series. The deadlock fix is kind of serious and tagged for stable, the rest is business as usual. - Fix two deadlocks around the pin control mutexes, a long-standing issue that manifest itself in plug/unplug of pin controllers. (Tagged for stable.) - Handle an error path with zero functions in the Qualcomm pin controller. - Drop a bogus second GPIO chip added in the Lantiq driver. - Fix sudden IRQ loss on Rockchip pin controllers. - Register the GIT tree in MAINTAINERS" * tag 'pinctrl-v3.19-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: pinctrl: MAINTAINERS: add git tree reference pinctrl: qcom: Don't iterate past end of function array pinctrl: lantiq: remove bogus of_gpio_chip_add pinctrl: Fix two deadlocks pinctrl: rockchip: Avoid losing interrupts when supporting both edges
2015-01-20Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds31-192/+343
Pull networking fixes from David Miller: 1) Socket addresses returned in the error queue need to be fully initialized before being passed on to userspace, fix from Willem de Bruijn. 2) Interrupt handling fixes to davinci_emac driver from Tony Lindgren. 3) Fix races between receive packet steering and cpu hotplug, from Eric Dumazet. 4) Allowing netlink sockets to subscribe to unknown multicast groups leads to crashes, don't allow it. From Johannes Berg. 5) One to many socket races in SCTP fixed by Daniel Borkmann. 6) Put in a guard against the mis-use of ipv6 atomic fragments, from Hagen Paul Pfeifer. 7) Fix promisc mode and ethtool crashes in sh_eth driver, from Ben Hutchings. 8) NULL deref and double kfree fix in sxgbe driver from Girish K.S and Byungho An. 9) cfg80211 deadlock fix from Arik Nemtsov. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (36 commits) s2io: use snprintf() as a safety feature r8152: remove sram_read r8152: remove generic_ocp_read before writing bgmac: activate irqs only if there is nothing to poll bgmac: register napi before the device sh_eth: Fix ethtool operation crash when net device is down sh_eth: Fix promiscuous mode on chips without TSU ipv6: stop sending PTB packets for MTU < 1280 net: sctp: fix race for one-to-many sockets in sendmsg's auto associate genetlink: synchronize socket closing and family removal genetlink: disallow subscribing to unknown mcast groups genetlink: document parallel_ops net: rps: fix cpu unplug net: davinci_emac: Add support for emac on dm816x net: davinci_emac: Fix ioremap for devices with MDIO within the EMAC address space net: davinci_emac: Fix incomplete code for getting the phy from device tree net: davinci_emac: Free clock after checking the frequency net: davinci_emac: Fix runtime pm calls for davinci_emac net: davinci_emac: Fix hangs with interrupts ip: zero sockaddr returned on error queue ...
2015-01-20Merge git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6Linus Torvalds22-4/+27
Pull crypto fix from Herbert Xu: "This fixes a regression that arose from the change to add a crypto prefix to module names which was done to prevent the loading of arbitrary modules through the Crypto API. In particular, a number of modules were missing the crypto prefix which meant that they could no longer be autoloaded" * git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: crypto: add missing crypto module aliases
2015-01-19s2io: use snprintf() as a safety featureDan Carpenter1-3/+8
"sp->desc[i]" has 25 characters. "dev->name" has 15 characters. If we used all 15 characters then the sprintf() would overflow. I changed the "sprintf(sp->name, "%s Neterion %s"" to snprintf(), as well, even though it can't overflow just to be consistent. Signed-off-by: Dan Carpenter <[email protected]> Signed-off-by: David S. Miller <[email protected]>
Powered by cgit, Gruvboxed by Blaster4385.