| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Requesting a threaded interrupt without a primary handler and without
IRQF_ONESHOT is dangerous, and after commit 1c6c6952 ("genirq: Reject
bogus threaded irq requests"), these requests are rejected. This causes
->probe() to fail, and the RTC driver not to be availble.
To fix, add IRQF_ONESHOT to the IRQ flags.
Tested on OMAP3730/OveroSTORM and OMAP4430/Panda board using rtcwake to
wake from system suspend multiple times.
Signed-off-by: Kevin Hilman <[email protected]>
Cc: Alessandro Zummo <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
fat_encode_fh() can fetch an invalid i_pos value on systems where 64-bit
accesses are not atomic. Make it use the same accessor as the rest of the
FAT code.
Signed-off-by: Steven J. Magnani <[email protected]>
Acked-by: OGAWA Hirofumi <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Add the OMAP CPUFreq driver to the list of files in the OMAP Power
Management section.
I've already been maintaining this driver, this just makes it official.
Signed-off-by: Kevin Hilman <[email protected]>
Cc: Arnd Bergmann <[email protected]>
Cc: "Rafael J. Wysocki" <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
The code here has a nested spin_lock_irqsave(). It's not needed since
IRQs are already disabled and it causes a problem because it means that
IRQs won't be enabled again at the end. The second call to
spin_lock_irqsave() will overwrite the value of irq_flags and we can't
restore the proper settings.
Signed-off-by: Dan Carpenter <[email protected]>
Signed-off-by: Robin Holt <[email protected]>
Cc: Jack Steiner <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
There is a bug in the below scenario for !CONFIG_MMU:
1. create a new file
2. mmap the file and write to it
3. read the file can't get the correct value
Because
sys_read() -> generic_file_aio_read() -> simple_readpage() -> clear_page()
which causes the page to be zeroed.
Add SetPageUptodate() to ramfs_nommu_expand_for_mapping() so that
generic_file_aio_read() do not call simple_readpage().
Signed-off-by: Bob Liu <[email protected]>
Cc: Hugh Dickins <[email protected]>
Cc: David Howells <[email protected]>
Cc: Geert Uytterhoeven <[email protected]>
Cc: Greg Ungerer <[email protected]>
Cc: <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Fixes
WARNING: at irq/handle.c:146 handle_irq_event_percpu+0x19c/0x1b8()
irq 25 handler mxc_rtc_interrupt+0x0/0xac enabled interrupts
Modules linked in:
(unwind_backtrace+0x0/0xf0) from (warn_slowpath_common+0x4c/0x64)
(warn_slowpath_common+0x4c/0x64) from (warn_slowpath_fmt+0x30/0x40)
(warn_slowpath_fmt+0x30/0x40) from (handle_irq_event_percpu+0x19c/0x1b8)
(handle_irq_event_percpu+0x19c/0x1b8) from (handle_irq_event+0x28/0x38)
(handle_irq_event+0x28/0x38) from (handle_level_irq+0x80/0xc4)
(handle_level_irq+0x80/0xc4) from (generic_handle_irq+0x24/0x38)
(generic_handle_irq+0x24/0x38) from (handle_IRQ+0x30/0x84)
(handle_IRQ+0x30/0x84) from (avic_handle_irq+0x2c/0x4c)
(avic_handle_irq+0x2c/0x4c) from (__irq_svc+0x40/0x60)
Exception stack(0xc050bf60 to 0xc050bfa8)
bf60: 00000001 00000000 003c4208 c0018e20 c050a000 c050a000 c054a4c8 c050a000
bf80: c05157a8 4117b363 80503bb4 00000000 01000000 c050bfa8 c0018e2c c000e808
bfa0: 60000013 ffffffff
(__irq_svc+0x40/0x60) from (default_idle+0x1c/0x30)
(default_idle+0x1c/0x30) from (cpu_idle+0x68/0xa8)
(cpu_idle+0x68/0xa8) from (start_kernel+0x22c/0x26c)
Signed-off-by: Benoît Thébaudeau <[email protected]>
Cc: Alessandro Zummo <[email protected]>
Cc: Sascha Hauer <[email protected]>
Acked-by: Uwe Kleine-König <[email protected]>
Cc: <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
We should goto error to release memory resource if hotadd_new_pgdat()
failed.
Signed-off-by: Wen Congyang <[email protected]>
Cc: Yasuaki ISIMATU <[email protected]>
Acked-by: David Rientjes <[email protected]>
Cc: Len Brown <[email protected]>
Cc: "Brown, Len" <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Fix the build error:
include/linux/regset.h: In function 'user_regset_copyout_zero':
include/linux/regset.h:289:3: error: implicit declaration of function '__clear_user' [-Werror=implicit-function-declaration]
Signed-off-by: Geert Uytterhoeven <[email protected]>
Cc: Yoshinori Sato <[email protected]>
Cc: Tony Breeds <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
__gu_val is const if the passed ptr is const, giving:
include/linux/pagemap.h: In function 'fault_in_pages_readable':
include/linux/pagemap.h:442:2: error: assignment of read-only variable '__gu_val'
include/linux/pagemap.h:448:4: error: assignment of read-only variable '__gu_val'
include/linux/pagemap.h: In function 'fault_in_multipages_readable':
include/linux/pagemap.h:499:3: error: assignment of read-only variable '__gu_val'
include/linux/pagemap.h:508:3: error: assignment of read-only variable '__gu_val'
make[4]: *** [init/main.o] Error 1
As we don't care about the actual value of __gu_val in the unhandled
case (it will cause a link error anyway), just remove the assignment.
Signed-off-by: Geert Uytterhoeven <[email protected]>
Cc: Yoshinori Sato <[email protected]>
Cc: Tony Breeds <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Fix the build error:
arch/h8300/kernel/time.c: In function 'h8300_timer_tick':
arch/h8300/kernel/time.c:39:2: error: implicit declaration of function 'get_irq_regs' [-Werror=implicit-function-declaration]
arch/h8300/kernel/time.c:39:42: error: invalid type argument of '->' (have 'int')
Signed-off-by: Geert Uytterhoeven <[email protected]>
Cc: Yoshinori Sato <[email protected]>
Cc: Tony Breeds <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
The keyword is "static", not "statis":
arch/h8300/kernel/signal.c:455:8: error: expected '=', ',', ';', 'asm' or '__attribute__' before 'void'
arch/h8300/kernel/signal.c: In function 'do_notify_resume':
arch/h8300/kernel/signal.c:511:3: error: implicit declaration of function 'do_signal' [-Werror=implicit-function-declaration]
arch/h8300/kernel/signal.c: At top level:
arch/h8300/kernel/signal.c:414:1: warning: 'handle_signal' defined but not used [-Wunused-function]
Introduced in commit 7ae4e32a6514 ("h8300: switch to saved_sigmask-based
sigsuspend/rt_sigsuspend")
Signed-off-by: Geert Uytterhoeven <[email protected]>
Cc: Al Viro <[email protected]>
Cc: Yoshinori Sato <[email protected]>
Cc: Tony Breeds <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Fix the h8300 build error:
kernel/sched/core.c: In function 'context_switch':
kernel/sched/core.c:2061:2: error: implicit declaration of function 'arch_start_context_switch' [-Werror=implicit-function-declaration]
Signed-off-by: Geert Uytterhoeven <[email protected]>
Cc: Yoshinori Sato <[email protected]>
Cc: Tony Breeds <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Device Tree is enabled
Without this patch, if Device Tree is enabled the AB8500 RTC wouldn't get
probed at all, as there is no reference to it from platform code. This
patch ensures the driver is probed during normal DT start-up.
[[email protected]: checkpatch fixes]
Signed-off-by: Lee Jones <[email protected]>
Cc: Alessandro Zummo <[email protected]>
Acked-by: Linus Walleij <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
This driver's IRQ registration is failing because the kernel now forces
IRQs to be ONESHOT if no IRQ handler is passed.
Signed-off-by: Lee Jones <[email protected]>
Cc: Alessandro Zummo <[email protected]>
Cc: <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
If page migration cannot charge the temporary page to the memcg,
migrate_pages() will return -ENOMEM. This isn't considered in memory
compaction however, and the loop continues to iterate over all
pageblocks trying to isolate and migrate pages. If a small number of
very large memcgs happen to be oom, however, these attempts will mostly
be futile leading to an enormous amout of cpu consumption due to the
page migration failures.
This patch will short circuit and fail memory compaction if
migrate_pages() returns -ENOMEM. COMPACT_PARTIAL is returned in case
some migrations were successful so that the page allocator will retry.
Signed-off-by: David Rientjes <[email protected]>
Acked-by: Mel Gorman <[email protected]>
Cc: Minchan Kim <[email protected]>
Cc: Kamezawa Hiroyuki <[email protected]>
Cc: Rik van Riel <[email protected]>
Cc: Andrea Arcangeli <[email protected]>
Cc: <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
"no other files mapped" requirement from my previous patch (c/r: prctl:
update prctl_set_mm_exe_file() after mm->num_exe_file_vmas removal) is too
paranoid, it forbids operation even if there mapped one shared-anon vma.
Let's check that current mm->exe_file already unmapped, in this case
exe_file symlink already outdated and its changing is reasonable.
Plus, this patch fixes exit code in case operation success.
Signed-off-by: Konstantin Khlebnikov <[email protected]>
Reported-by: Cyrill Gorcunov <[email protected]>
Tested-by: Cyrill Gorcunov <[email protected]>
Cc: Oleg Nesterov <[email protected]>
Cc: Matt Helsley <[email protected]>
Cc: Kees Cook <[email protected]>
Cc: KOSAKI Motohiro <[email protected]>
Cc: Tejun Heo <[email protected]>
Cc: Pavel Emelyanov <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
As ocfs2_fallocate() will invoke __ocfs2_change_file_space() with a NULL
as the first parameter (file), it may trigger a NULL pointer dereferrence
due to a missing check.
Addresses http://bugs.launchpad.net/bugs/1006012
Signed-off-by: Luis Henriques <[email protected]>
Reported-by: Bret Towe <[email protected]>
Tested-by: Bret Towe <[email protected]>
Cc: Sunil Mushran <[email protected]>
Acked-by: Joel Becker <[email protected]>
Acked-by: Mark Fasheh <[email protected]>
Cc: <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Fix the warnings:
arch/mn10300/kernel/irq.c:173:7: warning: "CONFIG_MN10300_TTYSM1_TIMER9" is not defined [-Wundef]
arch/mn10300/kernel/irq.c:175:7: warning: "CONFIG_MN10300_TTYSM1_TIMER3" is not defined [-Wundef]
Signed-off-by: Geert Uytterhoeven <[email protected]>
Cc: David Howells <[email protected]>
Cc: Koichi Yasutake <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Fix the warnings:
arch/mn10300/mm/dma-alloc.c: At top level:
arch/mn10300/mm/dma-alloc.c:63:1: warning: data definition has no type or storage class [enabled by default]
arch/mn10300/mm/dma-alloc.c:63:1: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL' [-Wimplicit-int]
arch/mn10300/mm/dma-alloc.c:63:1: warning: parameter names (without types) in function declaration [enabled by default]
arch/mn10300/mm/dma-alloc.c:75:1: warning: data definition has no type or storage class [enabled by default]
arch/mn10300/mm/dma-alloc.c:75:1: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL' [-Wimplicit-int]
arch/mn10300/mm/dma-alloc.c:75:1: warning: parameter names (without types) in function declaration [enabled by default]
Signed-off-by: Geert Uytterhoeven <[email protected]>
Cc: David Howells <[email protected]>
Cc: Koichi Yasutake <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Fix the warning:
arch/mn10300/kernel/traps.c:304:1: warning: data definition has no type or storage class [enabled by default]
arch/mn10300/kernel/traps.c:304:1: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL' [-Wimplicit-int]
arch/mn10300/kernel/traps.c:304:1: warning: parameter names (without types) in function declaration [enabled by default]
Signed-off-by: Geert Uytterhoeven <[email protected]>
Cc: David Howells <[email protected]>
Cc: Koichi Yasutake <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Fix the nm10300 build failure:
In file included from arch/mn10300/kernel/csrc-mn10300.c:14:0:
arch/mn10300/kernel/internal.h:42:1: error: unknown type name 'irqreturn_t'
Signed-off-by: Geert Uytterhoeven <[email protected]>
Cc: David Howells <[email protected]>
Cc: Koichi Yasutake <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Fix the warning:
include/linux/ptrace.h:66:0: warning: "PTRACE_O_TRACESYSGOOD" redefined [enabled by default]
arch/mn10300/include/asm/ptrace.h:85:0: note: this is the location of the previous definition
We already have it in <linux/ptrace.h>, so remove it from <asm/ptrace.h>
Signed-off-by: Geert Uytterhoeven <[email protected]>
Cc: David Howells <[email protected]>
Cc: Koichi Yasutake <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Move the static inline function setup_jiffies_interrupt() from
<asm/timex.h> to arch/mn10300/kernel/cevt-mn10300.c, which is its only
callsite.
This allows to remove the inclusion of <asm/hardirq.h> and <linux/irq.h>
from <asm/timex.h> and <unit/timex.h>, fixing include hell like:
include/linux/jiffies.h:260:31: warning: "CLOCK_TICK_RATE" is not defined [-Wundef]
include/linux/jiffies.h:260:31: warning: "CLOCK_TICK_RATE" is not defined [-Wundef]
include/linux/jiffies.h:46:42: error: division by zero in #if
...
make[4]: *** [arch/mn10300/kernel/asm-offsets.s] Error 1
and (after a quick hack for the above by defining CLOCK_TICK_RATE in
<linux/jiffies.h>):
In file included from include/linux/notifier.h:15:0,
from include/linux/memory_hotplug.h:6,
from include/linux/mmzone.h:718,
from include/linux/gfp.h:4,
from include/linux/irq.h:20,
from arch/mn10300/unit-asb2303/include/unit/timex.h:15,
from arch/mn10300/include/asm/timex.h:15,
from include/linux/timex.h:174,
from include/linux/jiffies.h:8,
from include/linux/ktime.h:25,
from include/linux/timer.h:5,
from include/linux/workqueue.h:8,
include/linux/srcu.h:55:22: error: field 'work' has incomplete type
As a consequence, we do need a few more inclusions of <asm/irq.h>, namely
in arch/mn10300/unit-asb2303/smc91111.c and
arch/mn10300/unit-asb2305/unit-init.c.
Signed-off-by: Geert Uytterhoeven <[email protected]>
Cc: David Howells <[email protected]>
Cc: Koichi Yasutake <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
`config' is freed and is then used in the rtc_device_unregister() call,
causing a kernel panic.
Signed-off-by: Devendra Naga <[email protected]>
Reviewed-by: Viresh Kumar <[email protected]>
Cc: Alessandro Zummo <[email protected]>
Cc: <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
kswapd_stop() is called to destroy the kswapd work thread when all memory
of a NUMA node has been offlined. But kswapd_stop() only terminates the
work thread without resetting NODE_DATA(nid)->kswapd to NULL. The stale
pointer will prevent kswapd_run() from creating a new work thread when
adding memory to the memory-less NUMA node again. Eventually the stale
pointer may cause invalid memory access.
An example stack dump as below. It's reproduced with 2.6.32, but latest
kernel has the same issue.
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffff81051a94>] exit_creds+0x12/0x78
PGD 0
Oops: 0000 [#1] SMP
last sysfs file: /sys/devices/system/memory/memory391/state
CPU 11
Modules linked in: cpufreq_conservative cpufreq_userspace cpufreq_powersave acpi_cpufreq microcode fuse loop dm_mod tpm_tis rtc_cmos i2c_i801 rtc_core tpm serio_raw pcspkr sg tpm_bios igb i2c_core iTCO_wdt rtc_lib mptctl iTCO_vendor_support button dca bnx2 usbhid hid uhci_hcd ehci_hcd usbcore sd_mod crc_t10dif edd ext3 mbcache jbd fan ide_pci_generic ide_core ata_generic ata_piix libata thermal processor thermal_sys hwmon mptsas mptscsih mptbase scsi_transport_sas scsi_mod
Pid: 7949, comm: sh Not tainted 2.6.32.12-qiuxishi-5-default #92 Tecal RH2285
RIP: 0010:exit_creds+0x12/0x78
RSP: 0018:ffff8806044f1d78 EFLAGS: 00010202
RAX: 0000000000000000 RBX: ffff880604f22140 RCX: 0000000000019502
RDX: 0000000000000000 RSI: 0000000000000202 RDI: 0000000000000000
RBP: ffff880604f22150 R08: 0000000000000000 R09: ffffffff81a4dc10
R10: 00000000000032a0 R11: ffff880006202500 R12: 0000000000000000
R13: 0000000000c40000 R14: 0000000000008000 R15: 0000000000000001
FS: 00007fbc03d066f0(0000) GS:ffff8800282e0000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000000000 CR3: 000000060f029000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process sh (pid: 7949, threadinfo ffff8806044f0000, task ffff880603d7c600)
Stack:
ffff880604f22140 ffffffff8103aac5 ffff880604f22140 ffffffff8104d21e
ffff880006202500 0000000000008000 0000000000c38000 ffffffff810bd5b1
0000000000000000 ffff880603d7c600 00000000ffffdd29 0000000000000003
Call Trace:
__put_task_struct+0x5d/0x97
kthread_stop+0x50/0x58
offline_pages+0x324/0x3da
memory_block_change_state+0x179/0x1db
store_mem_state+0x9e/0xbb
sysfs_write_file+0xd0/0x107
vfs_write+0xad/0x169
sys_write+0x45/0x6e
system_call_fastpath+0x16/0x1b
Code: ff 4d 00 0f 94 c0 84 c0 74 08 48 89 ef e8 1f fd ff ff 5b 5d 31 c0 41 5c c3 53 48 8b 87 20 06 00 00 48 89 fb 48 8b bf 18 06 00 00 <8b> 00 48 c7 83 18 06 00 00 00 00 00 00 f0 ff 0f 0f 94 c0 84 c0
RIP exit_creds+0x12/0x78
RSP <ffff8806044f1d78>
CR2: 0000000000000000
[[email protected]: add pglist_data.kswapd locking comments]
Signed-off-by: Xishi Qiu <[email protected]>
Signed-off-by: Jiang Liu <[email protected]>
Acked-by: KAMEZAWA Hiroyuki <[email protected]>
Acked-by: KOSAKI Motohiro <[email protected]>
Acked-by: Mel Gorman <[email protected]>
Acked-by: David Rientjes <[email protected]>
Reviewed-by: Minchan Kim <[email protected]>
Cc: <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
The update of the hrtimer base offsets on all cpus cannot be made
atomically from the timekeeper.lock held and interrupt disabled region
as smp function calls are not allowed there.
clock_was_set(), which enforces the update on all cpus, is called
either from preemptible process context in case of do_settimeofday()
or from the softirq context when the offset modification happened in
the timer interrupt itself due to a leap second.
In both cases there is a race window for an hrtimer interrupt between
dropping timekeeper lock, enabling interrupts and clock_was_set()
issuing the updates. Any interrupt which arrives in that window will
see the new time but operate on stale offsets.
So we need to make sure that an hrtimer interrupt always sees a
consistent state of time and offsets.
ktime_get_update_offsets() allows us to get the current monotonic time
and update the per cpu hrtimer base offsets from hrtimer_interrupt()
to capture a consistent state of monotonic time and the offsets. The
function replaces the existing ktime_get() calls in hrtimer_interrupt().
The overhead of the new function vs. ktime_get() is minimal as it just
adds two store operations.
This ensures that any changes to realtime or boottime offsets are
noticed and stored into the per-cpu hrtimer base structures, prior to
any hrtimer expiration and guarantees that timers are not expired early.
Signed-off-by: John Stultz <[email protected]>
Reviewed-by: Ingo Molnar <[email protected]>
Acked-by: Peter Zijlstra <[email protected]>
Acked-by: Prarit Bhargava <[email protected]>
Cc: [email protected]
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Thomas Gleixner <[email protected]>
|
|
To finally fix the infamous leap second issue and other race windows
caused by functions which change the offsets between the various time
bases (CLOCK_MONOTONIC, CLOCK_REALTIME and CLOCK_BOOTTIME) we need a
function which atomically gets the current monotonic time and updates
the offsets of CLOCK_REALTIME and CLOCK_BOOTTIME with minimalistic
overhead. The previous patch which provides ktime_t offsets allows us
to make this function almost as cheap as ktime_get() which is going to
be replaced in hrtimer_interrupt().
Signed-off-by: Thomas Gleixner <[email protected]>
Reviewed-by: Ingo Molnar <[email protected]>
Acked-by: Peter Zijlstra <[email protected]>
Acked-by: Prarit Bhargava <[email protected]>
Cc: [email protected]
Signed-off-by: John Stultz <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Thomas Gleixner <[email protected]>
|
|
We need to update the base offsets from this code and we need to do
that under base->lock. Move the lock held region around the
ktime_get() calls. The ktime_get() calls are going to be replaced with
a function which gets the time and the offsets atomically.
Signed-off-by: Thomas Gleixner <[email protected]>
Reviewed-by: Ingo Molnar <[email protected]>
Acked-by: Peter Zijlstra <[email protected]>
Acked-by: Prarit Bhargava <[email protected]>
Cc: [email protected]
Signed-off-by: John Stultz <[email protected]>
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Thomas Gleixner <[email protected]>
|
|
We need to update the hrtimer clock offsets from the hrtimer interrupt
context. To avoid conversions from timespec to ktime_t maintain a
ktime_t based representation of those offsets in the timekeeper. This
puts the conversion overhead into the code which updates the
underlying offsets and provides fast accessible values in the hrtimer
interrupt.
Signed-off-by: Thomas Gleixner <[email protected]>
Signed-off-by: John Stultz <[email protected]>
Reviewed-by: Ingo Molnar <[email protected]>
Acked-by: Peter Zijlstra <[email protected]>
Acked-by: Prarit Bhargava <[email protected]>
Cc: [email protected]
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Thomas Gleixner <[email protected]>
|
|
The timekeeping code misses an update of the hrtimer subsystem after a
leap second happened. Due to that timers based on CLOCK_REALTIME are
either expiring a second early or late depending on whether a leap
second has been inserted or deleted until an operation is initiated
which causes that update. Unless the update happens by some other
means this discrepancy between the timekeeping and the hrtimer data
stays forever and timers are expired either early or late.
The reported immediate workaround - $ data -s "`date`" - is causing a
call to clock_was_set() which updates the hrtimer data structures.
See: http://www.sheeri.com/content/mysql-and-leap-second-high-cpu-and-fix
Add the missing clock_was_set() call to update_wall_time() in case of
a leap second event. The actual update is deferred to softirq context
as the necessary smp function call cannot be invoked from hard
interrupt context.
Signed-off-by: John Stultz <[email protected]>
Reported-by: Jan Engelhardt <[email protected]>
Reviewed-by: Ingo Molnar <[email protected]>
Acked-by: Peter Zijlstra <[email protected]>
Acked-by: Prarit Bhargava <[email protected]>
Cc: [email protected]
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Thomas Gleixner <[email protected]>
|
|
clock_was_set() cannot be called from hard interrupt context because
it calls on_each_cpu().
For fixing the widely reported leap seconds issue it is necessary to
call it from hard interrupt context, i.e. the timer tick code, which
does the timekeeping updates.
Provide a new function which denotes it in the hrtimer cpu base
structure of the cpu on which it is called and raise the hrtimer
softirq. We then execute the clock_was_set() notificiation from
softirq context in run_hrtimer_softirq(). The hrtimer softirq is
rarely used, so polling the flag there is not a performance issue.
[ tglx: Made it depend on CONFIG_HIGH_RES_TIMERS. We really should get
rid of all this ifdeffery ASAP ]
Signed-off-by: John Stultz <[email protected]>
Reported-by: Jan Engelhardt <[email protected]>
Reviewed-by: Ingo Molnar <[email protected]>
Acked-by: Peter Zijlstra <[email protected]>
Acked-by: Prarit Bhargava <[email protected]>
Cc: [email protected]
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Thomas Gleixner <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile
Pull arch/tile fix from Chris Metcalf:
"This is a single change to fix backtracing in big-endian mode."
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
arch/tile: big-endian: properly bswap instruction bundles when backtracing
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of three fixes for data corruption (libsas task file),
oops causing (NULL in scsi_cmd_to_driver) and driver failure (bnx2i).
The oops caused by the NULL in scsi_cmd_to_driver() manifests in
scsi_eh_send_cmd() and has been seen by several people now.
Signed-off-by: James Bottomley <[email protected]>"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] bnx2i: Removed the reference to the netdev->base_addr
[SCSI] libsas: fix taskfile corruption in sas_ata_qc_fill_rtf
[SCSI] Fix NULL dereferences in scsi_cmd_to_driver
|
|
Do not use MX2_CAMERA_SWAP16 and MX2_CAMERA_PACK_DIR_MSB flags. The driver
must negotiate with the attached sensor whether the mbus format is UYUV or
YUYV and set CSICR1 configuration accordingly.
This is needed for the video function on mach-imx27_visstrim_m10.c to
perform properly, since an earlier version of this patch has been proven
wrong and has been reverted and a commit, depending on it: "[media]
i.MX27: visstrim_m10: Remove use of MX2_CAMERA_SWAP16" is in the mainline.
Signed-off-by: Javier Martin <[email protected]>
Reviewed-by: Mauro Carvalho Chehab <[email protected]>
Acked-by: Laurent Pinchart <[email protected]>
[ [email protected]: move a macro definition to a more logical place ]
Signed-off-by: Guennadi Liakhovetski <[email protected]>
[ Applying directly because Mauro is on vacation - Linus ]
Signed-off-by: Linus Torvalds <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
- multiple omap2+ bug fixes
- a regression on ux500 dt support
- a build failure on shmobile
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: OMAP2+: omap2plus_defconfig: EHCI driver is not stable, disable it
ARM: shmobile: fix platsmp.c build when ARCH_SH73A0=n
ARM: ux500: Over-ride the DT device naming scheme for pinctrl
ARM: ux500: Fix build errors/warnings when MACH_UX500_DT is not set
of: address: Don't fail a lookup just because a node has no reg property
ARM: OMAP2+: hwmod code/clockdomain data: fix 32K sync timer
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fix from Rafael Wysocki:
"This removes ACPICA code that had already been removed once from the
kernel already by commit 2780cc4660e1 ("[ACPI] Fix suspend/resume
lockup issue by leaving Bus Master Arbitration enabled"), because it
was known to cause systems to lock up during resume from suspend, but
was re-introduced by mistake during the v3.4 merge window."
* tag 'pm-for-3.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / PM: Leave Bus Master Arbitration enabled for suspend/resume
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull printk fixes from Greg Kroah-Hartman:
"Here are some more printk fixes for 3.5-rc6. They resolve all known
outstanding issues with the printk changes that have been happening.
They have been tested by the people reporting the problems.
This hopefully should be it for the printk stuff for 3.5-final.
Signed-off-by: Greg Kroah-Hartman <[email protected]>"
* tag 'driver-core-3.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
kmsg: merge continuation records while printing
kmsg: /proc/kmsg - support reading of partial log records
kmsg: make sure all messages reach a newly registered boot console
kmsg: properly handle concurrent non-blocking read() from /proc/kmsg
kmsg: add the facility number to the syslog prefix
kmsg: escape the backslash character while exporting data
printk: replacing the raw_spin_lock/unlock with raw_spin_lock/unlock_irq
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg Kroah-Hartman:
"Here are a few fixes and new device ids for the 3.5-rc6 tree.
The PCI changes resolve a long-standing issue with resuming some EHCI
controllers. It has been acked by the PCI maintainer, and he asked
for it to go through my USB tree instead of his.
The xhci patches also resolve a number of reported issues.
Signed-off-by: Greg Kroah-Hartman <[email protected]>"
* tag 'usb-3.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
PCI: EHCI: fix crash during suspend on ASUS computers
USB: cdc-wdm: fix lockup on error in wdm_read
USB: metro-usb: fix tty_flip_buffer_push use
USB: option: Add MEDIATEK product ids
USB: option: add ZTE MF60
xhci: Fix hang on back-to-back Set TR Deq Ptr commands.
usb: Add support for root hub port status CAS
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull misc fix from Greg Kroah-Hartman:
"Here's a single MEI driver fix that resolves a regression from 3.4
that a number of people have reported (and sent to me in different
patches.)
Signed-off-by: Greg Kroah-Hartman <[email protected]>"
* tag 'char-misc-3.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
mei: pci_resume: set IRQF_ONESHOT for msi request_threaded_irq
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull a late GPIO fix from Linus Walleij:
"Grr! So typically -next washed out a bug in the bug fixes. This v2 of
the pull request fixes another OF/DT related issue caused by fixing
another OF/DT related issue, courtesy of Gerard Sintselaar.
So please pull the v2. Or pull it on top of the other one, whatever.
Sorry for the panic mode, I'm in the middle of the Swedish woods,
supposedly on vacation."
* tag 'fixes-for-v3.5-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio/gpio-tps65910: gpio_chip.of_node referenced without CONFIG_OF_GPIO defined
|
|
The declaration of arch_release_thread_info() needs a semicolon.
Signed-off-by: David Howells <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
PPC fix from Alex Graf: "It contains an important bug fix which
can lead to guest freezes when using PAPR guests with PR KVM."
* 'for-upstream-master' of git://github.com/agraf/linux-2.6:
powerpc/kvm: Fix "PR" KVM implementation of H_CEDE
Signed-off-by: Avi Kivity <[email protected]>
|
|
H_CEDE should enable the vcpu's MSR:EE bit. It does on "HV" KVM (it's
burried in the assembly code though) and as far as I can tell, qemu
does it as well.
Signed-off-by: Benjamin Herrenschmidt <[email protected]>
Signed-off-by: Alexander Graf <[email protected]>
|
|
The kernel no longer allows us to pass NULL for the hard handler
without also specifying IRQF_ONESHOT. IRQF_ONESHOT imposes latency
in the exit path that we don't need for MSI interrupts. Long term
we'd like to inject these interrupts from the hard handler when
possible. In the short term, we can create dummy hard handlers
that return us to the previous behavior. Credit to Michael for
original patch.
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=43328
Signed-off-by: Michael S. Tsirkin <[email protected]>
Signed-off-by: Alex Williamson <[email protected]>
Signed-off-by: Avi Kivity <[email protected]>
|
|
Signed-off-by: Ilia Katsnelson <[email protected]>
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
The device should be handled by xpad driver instead of generic HID driver.
Signed-off-by: Yuri Khan <[email protected]>
Acked-by: Jiri Kosina <[email protected]>
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
Fix a boot regression on Mackerel boards with sh_mobile_sdhi
in existing kernels causing:
genirq: Threaded irq requested with handler=NULL and !ONESHOT for irq XXX
caused by 1c6c6952 (genirq: Reject bogus threaded irq requests).
This is backported from Guennadi's patch:
"mmc: extend and rename cd-gpio helpers to handle more slot GPIO functions"
Reported-by: Rafael J. Wysocki <[email protected]>
Signed-off-by: Guennadi Liakhovetski <[email protected]>
Signed-off-by: Chris Ball <[email protected]>
|
|
This reverts commit 3d93576e(skip card initialization if
power class selection fails).
Problem has been reported when this is used with eMMC4.41
card with Tegra Platform. Till the issue is root caused,
bus width selection failure should not be treated as fatal.
Reported-by: Marc Dietrich <[email protected]>
Signed-Off-by: Venkatraman S <[email protected]>
CC: Ulf Hansson <[email protected]>
CC: Subhash Jadavani <[email protected]>
CC: Saugata Das <[email protected]>
Signed-off-by: Chris Ball <[email protected]>
|
|
commit 626f9914 added code to initialize gpio_chip.of_node, but if
CONFIG_OF_GPIO is not defined gps-tps65910 fails to build with an
error complaining gpio_chip has no member of_node. I ran into this
while doing a allyesconfig build on linux-next.
Signed-off-by: Gerard Snitselaar <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Yes, this is a *LATE* GPIO pull request with fixes for v3.5.
Grant moved across the planet and accidentally fell off the grid, so
he asked me to take over the GPIO merges for a while 10 days ago.
Since then I went over the archives and collected this pile of fixes,
and pulled two of them from the TI maintainer Kevin Hilman. Then
waited for them to at least hit linux-next once or twice."
GPIO fixes for v3.5:
- Invalid context restore on bank 0 for OMAP driver in runtime
suspend/resume cycle
- Check for NULL platform data in sta-2x11 driver
- Constrain selection of the V1 MSM GPIO driver to applicable platforms
(Kconfig issue)
- Make sure the correct output value is set in the wm8994 driver
- Export devm_gpio_request_one() so it can be used in modules.
Apparently some in-kernel modules can be configured to use this
leading to breakage.
- Check that the GPIO is valid in the lantiq driver
- Fix the flag bits introduced for v3.5, so they don't overlap
- Fix a device tree intialization bug for imx21-compatible devices
- Carry over the OF node to the TPS65910 GPIO chip struct
* tag 'fixes-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: tps65910: initialize of_node of gpio_chip
gpio/mxc: make irqs work for fsl,imx21-gpio devices
gpio: fix bits conflict for gpio flags
mips: pci-lantiq: Fix check for valid gpio
gpio: export devm_gpio_request_one
gpiolib: wm8994: Pay attention to the value set when enabling as output
gpio/msm_v1: CONFIG_GPIO_MSM_V1 is only available on three SoCs
gpio-sta2x11: don't use pdata if null
gpio/omap: fix invalid context restore of gpio bank-0
gpio/omap: fix irq loss while in idle with debounce on
|