| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
ARC linux uses 2 distribution modes for common interrupts: round robin
mode (IDU_M_DISTRI_RR) and a simple destination mode (IDU_M_DISTRI_DEST).
The first one is used when more than 1 cores may handle a common interrupt
and the second one is used when only 1 core may handle a common interrupt.
However idu_irq_set_affinity() always sets IDU_M_DISTRI_RR for all affinity
values. But there is no sense in setting of such mode if only 1 core must
handle a common interrupt.
Signed-off-by: Yuriy Kolerov <[email protected]>
Signed-off-by: Vineet Gupta <[email protected]>
|
|
This came up when reviewing code to address missing IRQ affinity
setting in AXS103 platform and/or implementing hierarchical IRQ domains
- smp_ipi_irq_setup() callers pass hwirq but in turn calls
request_percpu_irq() which expects a linux virq. So invoke
irq_find_mapping() to do the conversion
(also explicitify this in code by renaming the args appropriately)
- idu_of_init()/idu_cascade_isr() were similarly using linux virq where
hwirq is expected, so do the conversion using irqd_to_hwirq() helper
Signed-off-by: Yuriy Kolerov <[email protected]>
[vgupta: made changelog a bit concise a bit]
Signed-off-by: Vineet Gupta <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
- Four patches from Robin Murphy fix several issues with the recently
merged generic DT-bindings support for arm-smmu drivers
- A fix for a dead-lock issue in the VT-d driver, which shows up on
iommu hotplug
* tag 'iommu-fixes-v4.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/vt-d: Fix dead-locks in disable_dmar_iommu() path
iommu/arm-smmu: Fix out-of-bounds dereference
iommu/arm-smmu: Check that iommu_fwspecs are ours
iommu/arm-smmu: Don't inadvertently reject multiple SMMUv3s
iommu/arm-smmu: Work around ARM DMA configuration
|
|
For CONFIG_SERIAL_EARLYCON we need 800MHz for NPS SoC
The early console driver uses BASE_BAUD and not using dtb.
The default of 50MHz is NOT good for NPS SoC.
Signed-off-by: Noam Camus <[email protected]>
Signed-off-by: Vineet Gupta <[email protected]>
|
|
Today we register to plat_smp_ops.clear() method which actually
is acking the IPI.
However this is already taking care by our irqchip driver specifically
by the irq_chip.irq_eoi() method.
This is perfect timing where it should be done and no special handling
is needed at plat_smp_ops.clear().
Signed-off-by: Noam Camus <[email protected]>
Signed-off-by: Vineet Gupta <[email protected]>
|
|
This has caused a bunch of build failures at a few sites, with GNU
2015.12 and older as the assembler seems to need -mlock to be able to
grok llock/scond instructions for ARC700 builds.
different places since the
older tools still seem to release
of tools which most people are using seem to trip with the -mlock flag
not being passed.
This reverts commit c3005475889c7c730638f95d13be3360f0b33e98.
|
|
Returning -EINVAL from a bool-returning function
phm_check_smc_update_required_for_display_configuration has an unexpected
effect of returning true, which is probably not what was intended.
Replace -EINVAL by false.
The only place this function is called from is
psm_adjust_power_state_dynamic in
drivers/gpu/drm/amd/powerplay/eventmgr/psm.c:106:
if (!equal || phm_check_smc_update_required_for_display_configuration(hwmgr)) {
phm_apply_state_adjust_rules(hwmgr, requested, pcurrent);
phm_set_power_state(hwmgr, &pcurrent->hardware, &requested->hardware);
hwmgr->current_ps = requested;
}
It seems to expect a boolean value here.
This issue has been found using the following Coccinelle semantic patch
written by Peter Senna Tschudin:
<smpl>
@@
identifier f;
constant C;
typedef bool;
@@
bool f (...){
<+...
* return -C;
...+>
}
</smpl>
Reviewed-by: Alex Deucher <[email protected]>
Signed-off-by: Andrew Shadura <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
A recent bugfix replaced an out-of-bounds access with direct
use of unintialized data:
drivers/gpu/drm/amd/powerplay/hwmgr/smu7_hwmgr.c: In function 'smu7_patch_limits_vddc':
drivers/gpu/drm/amd/powerplay/hwmgr/smu7_hwmgr.c:2033:6: error: 'vddc' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/gpu/drm/amd/powerplay/hwmgr/smu7_hwmgr.c:2146:11: note: 'vddc' was declared here
drivers/gpu/drm/amd/powerplay/hwmgr/smu7_hwmgr.c:2033:6: error: 'vddci' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/gpu/drm/amd/powerplay/hwmgr/smu7_hwmgr.c:2146:17: note: 'vddci' was declared here
uint32_t vddc, vddci;
This initializes the data as before using the correct type.
Fixes: 77f7f71f5be1 ("drm/amdgpu/powerplay/smu7: fix static checker warning")
Signed-off-by: Arnd Bergmann <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
|
|
The type flags in the irq descriptor are there for historical reasons and
only updated via irq_modify_status() or irq_set_type(). Both functions also
update the type flags in irqdata. __setup_irq() is the only left over user
of the type flags in the irq descriptor.
If __setup_irq() is called with empty irq type flags, then the type flags
are retrieved from irqdata. If an interrupt is shared, then the type flags
are compared with the type flags stored in the irq descriptor.
On x86 the ioapic does not have a irq_set_type() callback because the type
is defined in the BIOS tables and cannot be changed. The type is stored in
irqdata at setup time without updating the type data in the irq
descriptor. As a result the comparison described above fails.
There is no point in updating the irq descriptor flags because the only
relevant storage is irqdata. Use the type flags from irqdata for both
retrieval and comparison in __setup_irq() instead.
Aside of that the print out in case of non matching type flags has the old
and new type flags arguments flipped. Fix that as well.
For correctness sake the flags stored in the irq descriptor should be
removed, but this is beyond the scope of this bugfix and will be done in a
later patch.
Fixes: 4b357daed698 ("genirq: Look-up trigger type if not specified by caller")
Reported-and-tested-by: Mika Westerberg <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Cc: Marc Zyngier <[email protected]>
Cc: Jon Hunter <[email protected]>
Cc: [email protected]
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1611072020360.3501@nanos
Signed-off-by: Thomas Gleixner <[email protected]>
|
|
It turns out that the disable_dmar_iommu() code-path tried
to get the device_domain_lock recursivly, which will
dead-lock when this code runs on dmar removal. Fix both
code-paths that could lead to the dead-lock.
Fixes: 55d940430ab9 ('iommu/vt-d: Get rid of domain->iommu_lock')
Signed-off-by: Joerg Roedel <[email protected]>
|
|
When we iterate a master's config entries, what we generally care
about is the entry's stream map index, rather than the entry index
itself, so it's nice to have the iterator automatically assign the
former from the latter. Unfortunately, booting with KASAN reveals
the oversight that using a simple comma operator results in the
entry index being dereferenced before being checked for validity,
so we always access one element past the end of the fwspec array.
Flip things around so that the check always happens before the index
may be dereferenced.
Fixes: adfec2e709d2 ("iommu/arm-smmu: Convert to iommu_fwspec")
Reported-by: Mark Rutland <[email protected]>
Signed-off-by: Robin Murphy <[email protected]>
Acked-by: Will Deacon <[email protected]>
Signed-off-by: Joerg Roedel <[email protected]>
|
|
We seem to have forgotten to check that iommu_fwspecs actually belong to
us before we go ahead and dereference their private data. Oops.
Fixes: 021bb8420d44 ("iommu/arm-smmu: Wire up generic configuration support")
Signed-off-by: Robin Murphy <[email protected]>
Signed-off-by: Joerg Roedel <[email protected]>
|
|
We now delay installing our per-bus iommu_ops until we know an SMMU has
successfully probed, as they don't serve much purpose beforehand, and
doing so also avoids fights between multiple IOMMU drivers in a single
kernel. However, the upshot of passing the return value of bus_set_iommu()
back from our probe function is that if there happens to be more than
one SMMUv3 device in a system, the second and subsequent probes will
wind up returning -EBUSY to the driver core and getting torn down again.
Avoid re-setting ops if ours are already installed, so that any genuine
failures stand out.
Fixes: 08d4ca2a672b ("iommu/arm-smmu: Support non-PCI devices with SMMUv3")
CC: Lorenzo Pieralisi <[email protected]>
CC: Hanjun Guo <[email protected]>
Signed-off-by: Robin Murphy <[email protected]>
Signed-off-by: Joerg Roedel <[email protected]>
|
|
The 32-bit ARM DMA configuration code predates the IOMMU core's default
domain functionality, and instead relies on allocating its own domains
and attaching any devices using the generic IOMMU binding to them.
Unfortunately, it does this relatively early on in the creation of the
device, before we've seen our add_device callback, which leads us to
attempt to operate on a half-configured master.
To avoid a crash, check for this situation on attach, but refuse to
play, as there's nothing we can do. This at least allows VFIO to keep
working for people who update their 32-bit DTs to the generic binding,
albeit with a few (innocuous) warnings from the DMA layer on boot.
Signed-off-by: Robin Murphy <[email protected]>
Signed-off-by: Will Deacon <[email protected]>
Signed-off-by: Joerg Roedel <[email protected]>
|
|
Currently the ALSA proc handler allows read or write even if the proc
file were write-only or read-only. It's mostly harmless, does thing
but allocating memory and ignores the input/output. But it doesn't
tell user about the invalid use, and it's confusing and inconsistent
in comparison with other proc files.
This patch adds some sanity checks and let the proc handler returning
an -EIO error when the invalid read/write is performed.
Cc: <[email protected]> # v4.2+
Signed-off-by: Takashi Iwai <[email protected]>
|
|
The ALSA proc handler allows currently the write in the unlimited size
until kmalloc() fails. But basically the write is supposed to be only
for small inputs, mostly for one line inputs, and we don't have to
handle too large sizes at all. Since the kmalloc error results in the
kernel warning, it's better to limit the size beforehand.
This patch adds the limit of 16kB, which must be large enough for the
currently existing code.
Cc: [email protected] # v4.2+
Signed-off-by: Takashi Iwai <[email protected]>
|
|
Need to ensure that reg_output is not updated while setting multiple
bits. This makes the mutex locking behaviour for the set_multiple call
consistent with that of the set_value call.
Cc: [email protected]
Fixes: b4818afeacbd ("gpio: pca953x: Add set_multiple to allow multiple")
Signed-off-by: Phil Reid <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
Commit 345ddcc882d8 ("ftrace: Have set_ftrace_pid use the bitmap like
events do") added a couple of this_cpu_read calls to the ftrace code.
On x86 this is not a problem, since it has single instructions to read
percpu data. Other architectures which use the generic variant now
have additional preempt_disable and preempt_enable calls in the core
ftrace code. This may lead to recursive calls and in result to a dead
machine, e.g. if preemption and debugging options are enabled.
To fix this use the notrace variant of preempt_disable and
preempt_enable within the generic percpu code.
Reported-and-bisected-by: Sebastian Ott <[email protected]>
Tested-by: Sebastian Ott <[email protected]>
Fixes: 345ddcc882d8 ("ftrace: Have set_ftrace_pid use the bitmap like events do")
Signed-off-by: Heiko Carstens <[email protected]>
Acked-by: Steven Rostedt <[email protected]>
Signed-off-by: Martin Schwidefsky <[email protected]>
|
|
gpiod_set_array_value_complex does not clear the bits field.
Therefore when the drivers set_multiple funciton is called bits outside
the mask are undefined and can be either set or not. So bank_val needs
to be masked with bank_mask before or with the reg_val cache.
Cc: [email protected]
Fixes: b4818afeacbd ("gpio: pca953x: Add set_multiple to allow multiple")
Signed-off-by: Phil Reid <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
The display of /proc/net/route has had a couple issues due to the fact that
when I originally rewrote most of fib_trie I made it so that the iterator
was tracking the next value to use instead of the current.
In addition it had an off by 1 error where I was tracking the first piece
of data as position 0, even though in reality that belonged to the
SEQ_START_TOKEN.
This patch updates the code so the iterator tracks the last reported
position and key instead of the next expected position and key. In
addition it shifts things so that all of the leaves start at 1 instead of
trying to report leaves starting with offset 0 as being valid. With these
two issues addressed this should resolve any off by one errors that were
present in the display of /proc/net/route.
Fixes: 25b97c016b26 ("ipv4: off-by-one in continuation handling in /proc/net/route")
Cc: Andy Whitcroft <[email protected]>
Reported-by: Jason Baron <[email protected]>
Tested-by: Jason Baron <[email protected]>
Signed-off-by: Alexander Duyck <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Add Qualcomm QCA tagging introduced in cafdc45c9 to the
list of supported protocols.
Signed-off-by: Fabian Mewes <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Acked-by: Florian Fainelli <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Virtio 1.0 spec says VIRTIO_F_ANY_LAYOUT and VIRTIO_NET_F_GSO are
legacy-only feature bits. Do not negotiate them in virtio 1 mode. Note
this is a spec violation so we need to backport it to stable/downstream
kernels.
Cc: [email protected]
Signed-off-by: Michael S. Tsirkin <[email protected]>
Reviewed-by: Cornelia Huck <[email protected]>
Acked-by: Jason Wang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
icmp6_send is called in response to some event. The skb may not have
the device set (skb->dev is NULL), but it is expected to have a dst set.
Update icmp6_send to use the dst on the skb to determine L3 domain.
Fixes: ca254490c8dfd ("net: Add VRF support to IPv6 stack")
Signed-off-by: David Ahern <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Signed-off-by: H. Nikolaus Schaller <[email protected]>
Acked-by: Peter Ujfalusi <[email protected]>
Acked-by: Rob Herring <[email protected]>
Signed-off-by: Tony Lindgren <[email protected]>
|
|
Signed-off-by: H. Nikolaus Schaller <[email protected]>
Reviewed-by: Peter Ujfalusi <[email protected]>
Signed-off-by: Tony Lindgren <[email protected]>
|
|
Will be needed for iio based drivers.
Signed-off-by: H. Nikolaus Schaller <[email protected]>
Signed-off-by: Tony Lindgren <[email protected]>
|
|
For OMAP4, volt_data is set in omap44xx_voltagedomains_init.
If the SoC is neither OMAP443X or OMAP446X, we end up with a
NULL in volt_data which causes a kernel oops.
This is the case when booting OMAP4470.
Signed-off-by: Nicolae Rosia <[email protected]>
Signed-off-by: Tony Lindgren <[email protected]>
|
|
In the case where has_uart4 is false, en_uart4_mask and grpsel_uart4_mask
are not initialized and so any garbage value is being logically or'd into
the write of PM_WKEN and OMAP3430_PM_MPUGRPSEL. Fix this by initializing
these masks to zero.
Signed-off-by: Colin Ian King <[email protected]>
Signed-off-by: Tony Lindgren <[email protected]>
|
|
Commit ("766a1fe78fc3 ARM: omap3: Add missing memory node") added
the memory node, but the patch didn't have the correct starting address.
This patch fixes the correct starting address.
Signed-off-by: Adam Ford <[email protected]>
Signed-off-by: Tony Lindgren <[email protected]>
|
|
AM437x makes use of the omap_l3_noc driver so explicitly select
OMAP_INTERCONNECT in the Kconfig for SOC_AM43XX to ensure it gets enabled
for AM43XX only builds.
Signed-off-by: Dave Gerlach <[email protected]>
Signed-off-by: Tony Lindgren <[email protected]>
|
|
With the printk cleanups merged into v4.9-rc1, we now get the omap
revision printed on multiple lines. Let's fix that and also remove the
extra empty space at the end of the features. And let's update things
to use scnprintf as suggested by Ivaylo Dimitrov
<[email protected]>.
Reported-by: Adam Ford <[email protected]>
Cc: Ivaylo Dimitrov <[email protected]>
Reviewed-by: Sebastian Reichel <[email protected]>
Signed-off-by: Tony Lindgren <[email protected]>
|
|
Fix the following warn:
fs/nfs/nfs4session.c: In function ‘nfs4_slot_seqid_in_use’:
fs/nfs/nfs4session.c:203:54: warning: ‘cur_seq’ may be used uninitialized in this function [-Wmaybe-uninitialized]
if (nfs4_slot_get_seqid(tbl, slotid, &cur_seq) == 0 &&
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~
cur_seq == seq_nr && test_bit(slotid, tbl->used_slots))
~~~~~~~~~~~~~~~~~
Signed-off-by: Shuah Khan <[email protected]>
Signed-off-by: Anna Schumaker <[email protected]>
|
|
We used to check for a valid layout type id before verifying pNFS flags
as an indicator for if we are using pNFS. This changed in 3132e49ece
with the introduction of multiple layout types, since now we are passing
an array of ids instead of just one. Since then, users have been seeing
a KERN_ERR printk show up whenever mounting NFS v4 without pNFS. This
patch restores the original behavior of exiting set_pnfs_layoutdriver()
early if we aren't using pNFS.
Fixes 3132e49ece ("pnfs: track multiple layout types in fsinfo
structure")
Reviewed-by: Jeff Layton <[email protected]>
Signed-off-by: Anna Schumaker <[email protected]>
|
|
cl_rpcclient starts as ERR_PTR(-EINVAL), and connections like that
are floating freely through the system. Most places check whether
pointer is valid before dereferencing it, but newly added code
in nfs_match_client does not.
Which causes crashes when more than one NFS mount point is present.
Signed-off-by: Petr Vandrovec <[email protected]>
Signed-off-by: Anna Schumaker <[email protected]>
|
|
We need to hold the rcu_read_lock() when calling rcu_dereference(),
otherwise we can't guarantee that the object being dereferenced still
exists.
Fixes: 39e5d2df ("SUNRPC search xprt switch for sockaddr")
Signed-off-by: Anna Schumaker <[email protected]>
|
|
The current code doesn't even compile as somehow the inline assembly
can't see the register names defined as ARC_RTC_*
I'm pretty sure It worked when I first got it merged, but the tools were
definitely different then.
So better to write this in "C" anyways.
CC: [email protected] #4.2+
Acked-by: Daniel Lezcano <[email protected]>
Signed-off-by: Vineet Gupta <[email protected]>
|
|
The original syscall only used to return errno to indicate if cmpxchg
succeeded. It was not returning the "previous" value which typical cmpxchg
callers are interested in to build their slowpaths or retry loops.
Given user preemption in syscall return path etc, it is not wise to
check this in userspace afterwards, but should be what kernel actually
observed in the syscall.
So change the syscall interface to always return the previous value and
additionally set Z flag to indicate whether operation succeeded or not
(just like ARM implementation when they used to have this syscall)
The flag approach avoids having to put_user errno which is nice given
the use case for this syscall cares mostly about the "previous" value.
Signed-off-by: Vineet Gupta <[email protected]>
|
|
In map_create(), we first find and create the map, then once that
suceeded, we charge it to the user's RLIMIT_MEMLOCK, and then fetch
a new anon fd through anon_inode_getfd(). The problem is, once the
latter fails f.e. due to RLIMIT_NOFILE limit, then we only destruct
the map via map->ops->map_free(), but without uncharging the previously
locked memory first. That means that the user_struct allocation is
leaked as well as the accounted RLIMIT_MEMLOCK memory not released.
Make the label names in the fix consistent with bpf_prog_load().
Fixes: aaac3ba95e4c ("bpf: charge user for creation of BPF maps and programs")
Signed-off-by: Daniel Borkmann <[email protected]>
Acked-by: Alexei Starovoitov <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Commit a6ed3ea65d98 ("bpf: restore behavior of bpf_map_update_elem")
added an extra per-cpu reserve to the hash table map to restore old
behaviour from pre prealloc times. When non-prealloc is in use for a
map, then problem is that once a hash table extra element has been
linked into the hash-table, and the hash table is destroyed due to
refcount dropping to zero, then htab_map_free() -> delete_all_elements()
will walk the whole hash table and drop all elements via htab_elem_free().
The problem is that the element from the extra reserve is first fed
to the wrong backend allocator and eventually freed twice.
Fixes: a6ed3ea65d98 ("bpf: restore behavior of bpf_map_update_elem")
Reported-by: Dmitry Vyukov <[email protected]>
Signed-off-by: Daniel Borkmann <[email protected]>
Acked-by: Alexei Starovoitov <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
sctp_wait_for_connect() currently already holds the asoc to keep it
alive during the sleep, in case another thread release it. But Andrey
Konovalov and Dmitry Vyukov reported an use-after-free in such
situation.
Problem is that __sctp_connect() doesn't get a ref on the asoc and will
do a read on the asoc after calling sctp_wait_for_connect(), but by then
another thread may have closed it and the _put on sctp_wait_for_connect
will actually release it, causing the use-after-free.
Fix is, instead of doing the read after waiting for the connect, do it
before so, and avoid this issue as the socket is still locked by then.
There should be no issue on returning the asoc id in case of failure as
the application shouldn't trust on that number in such situations
anyway.
This issue doesn't exist in sctp_sendmsg() path.
Reported-by: Dmitry Vyukov <[email protected]>
Reported-by: Andrey Konovalov <[email protected]>
Tested-by: Andrey Konovalov <[email protected]>
Signed-off-by: Marcelo Ricardo Leitner <[email protected]>
Reviewed-by: Xin Long <[email protected]>
Acked-by: Neil Horman <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Johan Hovold says:
====================
net: fix device reference leaks
This series fixes a number of device reference leaks (and one of_node
leak) due to failure to drop the references taken by bus_find_device()
and friends.
Note that the final two patches have been compile tested only.
v2
- hold reference to cpsw-phy-sel device while accessing private data as
requested by David. Also update the commit message. (patch 1/4)
- add linux-omap on CC where appropriate
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
Make sure to drop the reference taken by class_find_device() in
hnae_get_handle() on errors and when later releasing the handle.
Fixes: 6fe6611ff275 ("net: add Hisilicon Network Subsystem...")
Cc: Yisen Zhuang <[email protected]>
Cc: Salil Mehta <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Make sure to drop the references taken by bus_find_device() before
returning from emac_dev_open().
Note that phy_connect still takes a reference to the phy device.
Fixes: 5d69e0076a72 ("net: davinci_emac: switch to new mdio")
Cc: Mugunthan V N <[email protected]>
Cc: Grygorii Strashko <[email protected]>
Cc: [email protected]
Signed-off-by: Johan Hovold <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Make sure to drop the references taken by of_get_child_by_name() and
bus_find_device() before returning from cpsw_phy_sel().
Note that holding a reference to the cpsw-phy-sel device does not
prevent the devres-managed private data from going away.
Fixes: 5892cd135e16 ("drivers: net: cpsw-phy-sel: Add new driver...")
Cc: Mugunthan V N <[email protected]>
Cc: Grygorii Strashko <[email protected]>
Cc: [email protected]
Signed-off-by: Johan Hovold <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Make sure to drop the reference taken by bus_find_device_by_name()
before returning from phy_connect() and phy_attach().
Note that both function still take a reference to the phy device
through phy_attach_direct().
Fixes: e13934563db0 ("[PATCH] PHY Layer fixup")
Cc: Florian Fainelli <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fix from Will Deacon:
"It's been pretty quiet on the fixes side of things for us, but Artem
reported a build failure introduced during the merge window that
appears with older GCCs that do not support asm goto. The fix is
bigger than I'd like, but it's a mechnical move of some constants to
break an include dependency between atomic.h and jump_label.h when
!HAVE_JUMP_LABEL.
Summary:
- Fix build failure on compilers without asm goto"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Fix circular include of asm/lse.h through linux/jump_label.h
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull openrisc fix from Guenter Roeck:
"Fix openrisc crash caused by ro_init changes"
* tag 'openrisc-for-linus-v4.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
openrisc: Define __ro_after_init to avoid crash
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fix from Guenter Roeck:
"Fix resource leak on devm_kcalloc failure"
* tag 'hwmon-for-linus-v4.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (core) fix resource leak on devm_kcalloc failure
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
- modprobe-after-rmmod load failure bugfix for intel-ish, from Even Xu
- IRQ probing bugfix for intel-ish, from Srinivas Pandruvada
- attribute parsing fix in hid-sensor, from Ooi, Joyce
- other small misc fixes / quirky device additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: sensor: fix attributes in HID sensor interface
HID: intel-ish-hid: request_irq failure
HID: intel-ish-hid: Fix driver reinit failure
HID: intel-ish-hid: Move DMA disable code to new function
HID: intel-ish-hid: consolidate ish wake up operation
HID: usbhid: add ATEN CS962 to list of quirky devices
HID: intel-ish-hid: Fix !CONFIG_PM build warning
HID: sensor-hub: Fix packing of result buffer for feature report
|
|
On CZ/ST systems with AZ rather than ACP audio, we need to bail
early in hw_fini since there is nothing to do.
bug: https://bugs.freedesktop.org/show_bug.cgi?id=98276
Signed-off-by: Alex Deucher <[email protected]>
Cc: [email protected]
|