| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
sp_usb_phy_probe() will call platform_get_resource_byname() that may fail
and return NULL. devm_ioremap() will use usbphy->moon4_res_mem->start as
input, which may causes null-ptr-deref. Check the ret value of
platform_get_resource_byname() to avoid the null-ptr-deref.
Fixes: 99d9ccd97385 ("phy: usb: Add USB2.0 phy driver for Sunplus SP7021")
Signed-off-by: Shang XiaoJing <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Vinod Koul <[email protected]>
|
|
Although rare, ssam_request_sync_init() can fail. In that case, the
request should be freed via ssam_request_sync_free(). Currently it is
leaked instead. Fix this.
Fixes: c167b9c7e3d6 ("platform/surface: Add Surface Aggregator subsystem")
Signed-off-by: Maximilian Luz <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Hans de Goede <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
|
|
It is possible that we (the host/kernel driver) receive command messages
that are not intended for us. Ignore those for now.
The whole story is a bit more complicated: It is possible to enable
debug output on SAM, which is sent via SSH command messages. By default
this output is sent to a debug connector, with its own target ID
(TID=0x03). It is possible to override the target of the debug output
and set it to the host/kernel driver. This, however, does not change the
original target ID of the message. Meaning, we receive messages with
TID=0x03 (debug) but expect to only receive messages with TID=0x00
(host).
The problem is that the different target ID also comes with a different
scope of request IDs. In particular, these do not follow the standard
event rules (i.e. do not fall into a set of small reserved values).
Therefore, current message handling interprets them as responses to
pending requests and tries to match them up via the request ID. However,
these debug output messages are not in fact responses, and therefore
this will at best fail to find the request and at worst pass on the
wrong data as response for a request.
Therefore ignore any command messages not intended for us (host) for
now. We can implement support for the debug messages once we have a
better understanding of them.
Note that this may also provide a bit more stability and avoid some
driver confusion in case any other targets want to talk to us in the
future, since we don't yet know what to do with those as well. A warning
for the dropped messages should suffice for now and also give us a
chance of discovering new targets if they come along without any
potential for bugs/instabilities.
Fixes: c167b9c7e3d6 ("platform/surface: Add Surface Aggregator subsystem")
Signed-off-by: Maximilian Luz <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Hans de Goede <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
|
|
Pull NVMe fixes from Christoph:
"nvme fixes for Linux 6.2
- Identify quirks for Apple controllers (Hector Martin)
- fix error handling in nvme_pci_enable (Tong Zhang)
- refuse unprivileged passthrough on partitions (Christoph Hellwig)
- fix MAINTAINERS to not match nvmem subsystem headers (Russell King)"
* tag 'nvme-6.2-2023-01-12' of git://git.infradead.org/nvme:
MAINTAINERS: stop nvme matching for nvmem files
nvme: don't allow unprivileged passthrough on partitions
nvme: replace the "bool vec" arguments with flags in the ioctl path
nvme: remove __nvme_ioctl
nvme-pci: fix error handling in nvme_pci_enable()
nvme-pci: add NVME_QUIRK_IDENTIFY_CNS quirk to Apple T2 controllers
nvme-apple: add NVME_QUIRK_IDENTIFY_CNS quirk to fix regression
|
|
If we have multiple requests waiting on the same target poll waitqueue,
then it's quite possible to get a request triggered and get disappointed
in not being able to make any progress with it. If we race in doing so,
we'll potentially leave the poll request on the internal tables, but
removed from the waitqueue. That means that any subsequent trigger of
the poll waitqueue will not kick that request into action, causing an
application to potentially wait for completion of a request that will
never happen.
Fix this by adding a new poll return state, IOU_POLL_REISSUE. Rather
than have complicated logic for how to re-arm a given type of request,
just punt it for a reissue.
While in there, move the 'ret' variable to the only section where it
gets used. This avoids confusion the scope of it.
Cc: [email protected]
Fixes: eb0089d629ba ("io_uring: single shot poll removal optimisation")
Signed-off-by: Jens Axboe <[email protected]>
|
|
Add touchscreen info for the CSL Panther Tab HD.
Signed-off-by: Michael Klein <[email protected]>
Link: https://lore.kernel.org/r/20221220121103.uiwn5l7fii2iggct@LLGMVZLB-0037
Reviewed-by: Hans de Goede <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
|
|
If smb311 posix is enabled, we send the intended mode for file
creation in the posix create context. Instead of using what's there on
the stack, create the mfsymlink file with 0644.
Fixes: ce558b0e17f8a ("smb3: Add posix create context for smb3.11 posix mounts")
Cc: [email protected]
Signed-off-by: Volker Lendecke <[email protected]>
Reviewed-by: Tom Talpey <[email protected]>
Reviewed-by: Paulo Alcantara (SUSE) <[email protected]>
Signed-off-by: Steve French <[email protected]>
|
|
When syncing a log, if we fail to update a log root in the log root tree,
we are aborting the transaction if the failure was not -ENOSPC. This is
excessive because there is a chance that a transaction commit can succeed,
and therefore avoid to turn the filesystem into RO mode. All we need to be
careful about is to mark the log for a full commit, which we already do,
to make sure no one commits a super block pointing to an outdated log root
tree.
So don't abort the transaction if we fail to update a log root in the log
root tree, and log an error if the failure is not -ENOSPC, so that it does
not go completely unnoticed.
CC: [email protected] # 6.0+
Reviewed-by: Josef Bacik <[email protected]>
Signed-off-by: Filipe Manana <[email protected]>
Signed-off-by: David Sterba <[email protected]>
|
|
When syncing the log, if we fail to write log tree extent buffers, we mark
the log for a full commit and abort the transaction. However we don't need
to abort the transaction, all we really need to do is to make sure no one
can commit a superblock pointing to new log tree roots. Just because we
got a failure writing extent buffers for a log tree, it does not mean we
will also fail to do a transaction commit.
One particular case is if due to a bug somewhere, when writing log tree
extent buffers, the tree checker detects some corruption and the writeout
fails because of that. Aborting the transaction can be very disruptive for
a user, specially if the issue happened on a root filesystem. One example
is the scenario in the Link tag below, where an isolated corruption on log
tree leaves was causing transaction aborts when syncing the log.
Link: https://lore.kernel.org/linux-btrfs/[email protected]/
CC: [email protected] # 5.15+
Reviewed-by: Josef Bacik <[email protected]>
Signed-off-by: Filipe Manana <[email protected]>
Signed-off-by: David Sterba <[email protected]>
|
|
When logging conflicting inodes, if we reach the maximum limit of inodes,
we return BTRFS_LOG_FORCE_COMMIT to force a transaction commit. However
we don't mark the log for full commit (with btrfs_set_log_full_commit()),
which means that once we leave the log transaction and before we commit
the transaction, some other task may sync the log, which is incomplete
as we have not logged all conflicting inodes, leading to some inconsistent
in case that log ends up being replayed.
So also call btrfs_set_log_full_commit() at add_conflicting_inode().
Fixes: e09d94c9e448 ("btrfs: log conflicting inodes without holding log mutex of the initial inode")
CC: [email protected] # 6.1
Reviewed-by: Josef Bacik <[email protected]>
Signed-off-by: Filipe Manana <[email protected]>
Signed-off-by: David Sterba <[email protected]>
|
|
Sometimes we log a directory without holding its VFS lock, so while we
logging it, dir index entries may be added or removed. This typically
happens when logging a dentry from a parent directory that points to a
new directory, through log_new_dir_dentries(), or when while logging
some other inode we also need to log its parent directories (through
btrfs_log_all_parents()).
This means that while we are at log_dir_items(), we may not find a dir
index key we found before, because it was deleted in the meanwhile, so
a call to btrfs_search_slot() may return 1 (key not found). In that case
we return from log_dir_items() with a success value (the variable 'err'
has a value of 0). This can lead to a few problems, specially in the case
where the variable 'last_offset' has a value of (u64)-1 (and it's
initialized to that when it was declared):
1) By returning from log_dir_items() with success (0) and a value of
(u64)-1 for '*last_offset_ret', we end up not logging any other dir
index keys that follow the missing, just deleted, index key. The
(u64)-1 value makes log_directory_changes() not call log_dir_items()
again;
2) Before returning with success (0), log_dir_items(), will log a dir
index range item covering a range from the last old dentry index
(stored in the variable 'last_old_dentry_offset') to the value of
'last_offset'. If 'last_offset' has a value of (u64)-1, then it means
if the log is persisted and replayed after a power failure, it will
cause deletion of all the directory entries that have an index number
between last_old_dentry_offset + 1 and (u64)-1;
3) We can end up returning from log_dir_items() with
ctx->last_dir_item_offset having a lower value than
inode->last_dir_index_offset, because the former is set to the current
key we are processing at process_dir_items_leaf(), and at the end of
log_directory_changes() we set inode->last_dir_index_offset to the
current value of ctx->last_dir_item_offset. So if for example a
deletion of a lower dir index key happened, we set
ctx->last_dir_item_offset to that index value, then if we return from
log_dir_items() because btrfs_search_slot() returned 1, we end up
returning from log_dir_items() with success (0) and then
log_directory_changes() sets inode->last_dir_index_offset to a lower
value than it had before.
This can result in unpredictable and unexpected behaviour when we
need to log again the directory in the same transaction, and can result
in ending up with a log tree leaf that has duplicated keys, as we do
batch insertions of dir index keys into a log tree.
So fix this by making log_dir_items() move on to the next dir index key
if it does not find the one it was looking for.
Reported-by: David Arendt <[email protected]>
Link: https://lore.kernel.org/linux-btrfs/[email protected]/
CC: [email protected] # 4.14+
Reviewed-by: Josef Bacik <[email protected]>
Signed-off-by: Filipe Manana <[email protected]>
Signed-off-by: David Sterba <[email protected]>
|
|
When logging a directory, at log_dir_items(), if we get an error when
attempting to search the subvolume tree for a dir index item, we end up
returning 0 (success) from log_dir_items() because 'err' is left with a
value of 0.
This can lead to a few problems, specially in the case the variable
'last_offset' has a value of (u64)-1 (and it's initialized to that when
it was declared):
1) By returning from log_dir_items() with success (0) and a value of
(u64)-1 for '*last_offset_ret', we end up not logging any other dir
index keys that follow the missing, just deleted, index key. The
(u64)-1 value makes log_directory_changes() not call log_dir_items()
again;
2) Before returning with success (0), log_dir_items(), will log a dir
index range item covering a range from the last old dentry index
(stored in the variable 'last_old_dentry_offset') to the value of
'last_offset'. If 'last_offset' has a value of (u64)-1, then it means
if the log is persisted and replayed after a power failure, it will
cause deletion of all the directory entries that have an index number
between last_old_dentry_offset + 1 and (u64)-1;
3) We can end up returning from log_dir_items() with
ctx->last_dir_item_offset having a lower value than
inode->last_dir_index_offset, because the former is set to the current
key we are processing at process_dir_items_leaf(), and at the end of
log_directory_changes() we set inode->last_dir_index_offset to the
current value of ctx->last_dir_item_offset. So if for example a
deletion of a lower dir index key happened, we set
ctx->last_dir_item_offset to that index value, then if we return from
log_dir_items() because btrfs_search_slot() returned an error, we end up
returning without any error from log_dir_items() and then
log_directory_changes() sets inode->last_dir_index_offset to a lower
value than it had before.
This can result in unpredictable and unexpected behaviour when we
need to log again the directory in the same transaction, and can result
in ending up with a log tree leaf that has duplicated keys, as we do
batch insertions of dir index keys into a log tree.
Fix this by setting 'err' to the value of 'ret' in case
btrfs_search_slot() or btrfs_previous_item() returned an error. That will
result in falling back to a full transaction commit.
Reported-by: David Arendt <[email protected]>
Link: https://lore.kernel.org/linux-btrfs/[email protected]/
Fixes: e02119d5a7b4 ("Btrfs: Add a write ahead tree log to optimize synchronous operations")
CC: [email protected] # 4.14+
Reviewed-by: Josef Bacik <[email protected]>
Signed-off-by: Filipe Manana <[email protected]>
Signed-off-by: David Sterba <[email protected]>
|
|
Since nfsd4_state_shrinker_count always calls mod_delayed_work with
0 delay, we can replace delayed_work with work_struct to save some
space and overhead.
Also add the call to cancel_work after unregister the shrinker
in nfs4_state_shutdown_net.
Signed-off-by: Dai Ngo <[email protected]>
Reviewed-by: Jeff Layton <[email protected]>
Signed-off-by: Chuck Lever <[email protected]>
|
|
The Microsoft Devkit 2023 is a an ARM64 based machine featuring a
Realtek 8153 USB3.0-to-GBit Ethernet adapter. As in their other
machines, Microsoft uses a custom USB device ID.
Add the respective ID values to the driver. This makes Ethernet work on
the MS Devkit device. The chip has been visually confirmed to be a
RTL8153.
Signed-off-by: Andre Przywara <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Paolo Abeni <[email protected]>
|
|
Commit 374146cad469 ("drm/vc4: Switch to drmm_mutex_init") converted,
among other functions, vc4_create_object() to use drmm_mutex_init().
However, that function is used to allocate a BO, and therefore the
mutex needs to be freed much sooner than when the DRM device is removed
from the system.
For each buffer allocation we thus end up allocating a small structure
as part of the DRM-managed mechanism that is never freed, eventually
leading us to no longer having any free memory anymore.
Let's switch back to mutex_init/mutex_destroy to deal with it properly.
Fixes: 374146cad469 ("drm/vc4: Switch to drmm_mutex_init")
Reviewed-by: Daniel Vetter <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
We are observing performance drop in many usecases which include
games, 3D benchmark applications,etc.. To solve this problem, We
are strictly not allowing top down flag enabled allocations to
steal the memory space from cpu visible region.
The idea is, we are sorting each order list entries in
ascending order and compare the last entry of each order
list in the freelist and return the max block.
This patch improves the 3D benchmark scores and solves
fragmentation issues.
All drm buddy selftests are verfied.
drm_buddy: pass:6 fail:0 skip:0 total:6
Signed-off-by: Arunpravin Paneer Selvam <[email protected]>
Acked-by: Christian König <[email protected]>
Acked-by: Alex Deucher <[email protected]>
Reviewed-by: Matthew Auld <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Signed-off-by: Christian König <[email protected]>
CC: Cc: [email protected] # 5.18+
|
|
The branch is explicitly taken if ttm == NULL which means that to avoid
a null pointer reference the ttm object can not be used inside. Switch
back to dst_mem to avoid kernel oops'es.
This fixes kernel oops'es with any buffer objects which don't have ttm_tt,
e.g. with vram based screen objects on vmwgfx.
Signed-off-by: Zack Rusin <[email protected]>
Fixes: e3c92eb4a84f ("drm/ttm: rework on ttm_resource to use size_t type")
Cc: Somalapuram Amaranath <[email protected]>
Cc: Christian König <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Signed-off-by: Christian König <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
- Fixes for long standing issues with accesses to spidev->spi during
teardown in the spidev userspace driver.
- Rename the newly added spi-cs-setup-ns DT property to be more in line
with our other delay properties before it becomes ABI.
- A few driver specific fixes.
* tag 'spi-fix-v6.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spidev: remove debug messages that access spidev->spi without locking
spi: spidev: fix a race condition when accessing spidev->spi
spi: Rename spi-cs-setup-ns property to spi-cs-setup-delay-ns
spi: dt-bindings: Rename spi-cs-setup-ns to spi-cs-setup-delay-ns
spi: cadence: Fix busy cycles calculation
spi: mediatek: Enable irq before the spi registration
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A couple of small driver specific fixes, one of which I queued for 6.1
but didn't actually send out so has had *plenty* of testing in -next"
* tag 'regulator-fix-v6.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: qcom-rpmh: PM8550 ldo11 regulator is an nldo
regulator: da9211: Use irq handler when ready
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD fixes from Miquel Raynal:
- cfi: Allow building spi-intel standalone to avoid build issues
- parsers: scpart: Fix __udivdi3 undefined on mips
- parsers: tplink_safeloader: Fix potential memory leak during parsing
- Update email of Tudor Ambarus
* tag 'mtd/fixes-for-6.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
MAINTAINERS: Update email of Tudor Ambarus
mtd: cfi: allow building spi-intel standalone
mtd: parsers: scpart: fix __udivdi3 undefined on mips
mtd: parsers: Fix potential memory leak in mtd_parser_tplink_safeloader_parse()
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v6.2
There's quite a few fixes here, mostly board specific apart from the SOF
power management ones. We also have some new quirks and Kconfig tweaks
to enable existing code on new platforms, and a one liner which exposes
the SOF firmware state in debugfs to aid with debugging.
There's also a SPI fix that I mistakenly put in the wrong queue and
did some merges on top of before I noticed, it seemed more trouble than
it was worth to unpick things. A copy of the same patch is also in the
spi tree.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Ten small fixes (less the one that cleaned up a reverted removal),
nine in drivers of which the ufs one is the most critical.
The single core patch is a minor speedup to error handling"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: libsas: Grab the ATA port lock in sas_ata_device_link_abort()
scsi: hisi_sas: Fix tag freeing for reserved tags
scsi: ufs: core: WLUN suspend SSU/enter hibern8 fail recovery
scsi: scsi_debug: Delete unreachable code in inquiry_vpd_b0()
scsi: mpi3mr: Refer CONFIG_SCSI_MPI3MR in Makefile
scsi: core: scsi_error: Do not queue pointless abort workqueue functions
scsi: storvsc: Fix swiotlb bounce buffer leak in confidential VM
scsi: iscsi: Fix multiple iSCSI session unbind events sent to userspace
scsi: mpi3mr: Remove usage of dma_get_required_mask() API
scsi: mpt3sas: Remove usage of dma_get_required_mask() API
|
|
The 2nd DDR clock for sam9x60 DDR controller is peripheral clock with
id 49.
Fixes: 1e5f532c2737 ("ARM: dts: at91: sam9x60: add device tree for soc and board")
Signed-off-by: Claudiu Beznea <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
The HP Spectre x360 13-aw0xxx devices use the ALC285 codec with GPIO 0x04
controlling the micmute LED and COEF 0x0b index 8 controlling the mute LED.
A quirk was added to make these work as well as a fixup.
Signed-off-by: Luka Guzenko <[email protected]>
Cc: <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
Commit 3f4c8211d982 ("x86/mm: Use mm_alloc() in poking_init()") broke
the kernel for running as Xen PV guest.
It seems as if the new address space is never activated before being
used, resulting in Xen rejecting to accept the new CR3 value (the PGD
isn't pinned).
Fix that by adding the now missing call of paravirt_arch_dup_mmap() to
poking_init(). That call was previously done by dup_mm()->dup_mmap() and
it is a NOP for all cases but for Xen PV, where it is just doing the
pinning of the PGD.
Fixes: 3f4c8211d982 ("x86/mm: Use mm_alloc() in poking_init()")
Signed-off-by: Juergen Gross <[email protected]>
Signed-off-by: Peter Zijlstra (Intel) <[email protected]>
Link: https://lkml.kernel.org/r/[email protected]
|
|
Add timeout polling wait for auxiliary timestamps snapshot FIFO clear bit
(ATSFC) to clear. This is to ensure no residue fifo value is being read
erroneously.
Fixes: f4da56529da6 ("net: stmmac: Add support for external trigger timestamping")
Cc: <[email protected]> # 5.10.x
Signed-off-by: Noor Azura Ahmad Tarmizi <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
when refreshing port id
Currently the driver sets the port invalid if one phy in the port is not
enabled, which may cause issues in expander situation. In directly attached
situation, if phy up doesn't occur in time when refreshing port id, the
port is incorrectly set to invalid which will also cause disk lost.
Therefore set a port invalid only if there are no devices attached to the
port.
Signed-off-by: Yihang Li <[email protected]>
Signed-off-by: Xiang Chen <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
Currently clear task set is used to abort all commands remaining in the
disk when the SAS disk is discovered, and if the disk is discovered by two
initiators, other I_T nexuses are also affected. So use abort task set
instead and take effect only on the specified I_T nexus.
Signed-off-by: Xingui Yang <[email protected]>
Signed-off-by: Xiang Chen <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Martin K. Petersen <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-01-10 (ixgbe, igc, iavf)
This series contains updates to ixgbe, igc, and iavf drivers.
Yang Yingliang adds calls to pci_dev_put() for proper ref count tracking
on ixgbe.
Christopher adds setting of Toggle on Target Time bits for proper
pulse per second (PPS) synchronization for igc.
Daniil Tatianin fixes, likely, copy/paste issue that misreported
destination instead of source for IP mask for iavf error.
* '10GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
iavf/iavf_main: actually log ->src mask when talking about it
igc: Fix PPS delta between two synchronized end-points
ixgbe: fix pci device refcount leak
====================
Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Alexander Duyck <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Before the commit under Fixes the page would have been released
from the pool before the napi_alloc_skb() call, so normal page
freeing was fine (released page == no longer in the pool).
After the change we just mark the page for recycling so it's still
in the pool if the skb alloc fails, we need to recycle.
Same commit added the same bug in the new bnxt_rx_multi_page_skb().
Fixes: 1dc4c557bfed ("bnxt: adding bnxt_xdp_build_skb to build skb from multibuffer xdp_buff")
Reviewed-by: Andy Gospodarek <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Currently, it used old rss size to get current tc mode. As a result, the
rss size is updated, but the tc mode is still configured based on the old
rss size.
So this patch fixes it by using the new rss size in both process.
Fixes: 93969dc14fcd ("net: hns3: refactor VF rss init APIs with new common rss init APIs")
Signed-off-by: Jie Wang <[email protected]>
Signed-off-by: Hao Lan <[email protected]>
Reviewed-by: Alexander Duyck <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Currently the nfsd-client shrinker is registered and unregistered at
the time the nfsd module is loaded and unloaded. The problem with this
is the shrinker is being registered before all of the relevant fields
in nfsd_net are initialized when nfsd is started. This can lead to an
oops when memory is low and the shrinker is called while nfsd is not
running.
This patch moves the register/unregister of nfsd-client shrinker from
module load/unload time to nfsd startup/shutdown time.
Fixes: 44df6f439a17 ("NFSD: add delegation reaper to react to low memory condition")
Reported-by: Mike Galbraith <[email protected]>
Signed-off-by: Dai Ngo <[email protected]>
Signed-off-by: Chuck Lever <[email protected]>
|
|
If signal_pending() returns true, schedule_timeout() will not be executed,
causing the waiting task to remain in the wait queue.
Fixed by adding a call to finish_wait(), which ensures that the waiting
task will always be removed from the wait queue.
Fixes: f4e44b393389 ("NFSD: delay unmount source's export after inter-server copy completed.")
Signed-off-by: Xingyuan Mo <[email protected]>
Reviewed-by: Jeff Layton <[email protected]>
Signed-off-by: Chuck Lever <[email protected]>
|
|
Fix the help text for the PRINTK_SAFE_LOG_BUF_SHIFT setting.
Link: https://lkml.kernel.org/r/[email protected]
Signed-off-by: Lizzy Fleckenstein <[email protected]>
Reviewed-by: Nick Desaulniers <[email protected]>
Cc: Masahiro Yamada <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
|
|
During the maple tree conversion of nommu, an error in counting the VMAs
was introduced by counting the existing VMA again. The counting used to
be decremented by one and incremented by two, but now it only increments
by two. Fix the counting error by moving the increment outside the
setup_vma_to_mm() function to the callers.
Link: https://lkml.kernel.org/r/[email protected]
Fixes: 8220543df148 ("nommu: remove uses of VMA linked list")
Signed-off-by: Liam R. Howlett <[email protected]>
Cc: Matthew Wilcox (Oracle) <[email protected]>
Cc: Vlastimil Babka <[email protected]>
Cc: Yu Zhao <[email protected]>
Cc: <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
|
|
When removing a VMA from the tree fails due to no memory, do not free the
VMA since a reference still exists.
Link: https://lkml.kernel.org/r/[email protected]
Fixes: 8220543df148 ("nommu: remove uses of VMA linked list")
Signed-off-by: Liam R. Howlett <[email protected]>
Cc: Matthew Wilcox (Oracle) <[email protected]>
Cc: Vlastimil Babka <[email protected]>
Cc: Yu Zhao <[email protected]>
Cc: <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
|
|
The preallocation of the maple tree nodes may leak if the error path to
"error_just_free" is taken. Fix this by moving the freeing of the maple
tree nodes to a shared location for all error paths.
Link: https://lkml.kernel.org/r/[email protected]
Fixes: 8220543df148 ("nommu: remove uses of VMA linked list")
Signed-off-by: Liam R. Howlett <[email protected]>
Cc: Matthew Wilcox (Oracle) <[email protected]>
Cc: Vlastimil Babka <[email protected]>
Cc: Yu Zhao <[email protected]>
Cc: <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
|
|
Update the email address for Robert's maintainer entries and fill in
.mailmap accordingly.
Link: https://lkml.kernel.org/r/[email protected]
Signed-off-by: Robert Foss <[email protected]>
Cc: Arnd Bergmann <[email protected]>
Cc: Baolin Wang <[email protected]>
Cc: Colin Ian King <[email protected]>
Cc: Kalle Valo <[email protected]>
Cc: Kirill Tkhai <[email protected]>
Cc: Qais Yousef <[email protected]>
Cc: Vasily Averin <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
|
|
vsyscall detection code uses direct call to the beginning of
the vsyscall page:
asm ("call %P0" :: "i" (0xffffffffff600000))
It generates "call rel32" instruction but it is not relocated if binary
is PIE, so binary segfaults into random userspace address and vsyscall
page status is detected incorrectly.
Do more direct:
asm ("call *%rax")
which doesn't do need any relocaltions.
Mark g_vsyscall as volatile for a good measure, I didn't find instruction
setting it to 0. Now the code is obviously correct:
xor eax, eax
mov rdi, rbp
mov rsi, rbp
mov DWORD PTR [rip+0x2d15], eax # g_vsyscall = 0
mov rax, 0xffffffffff600000
call rax
mov DWORD PTR [rip+0x2d02], 1 # g_vsyscall = 1
mov eax, DWORD PTR ds:0xffffffffff600000
mov DWORD PTR [rip+0x2cf1], 2 # g_vsyscall = 2
mov edi, [rip+0x2ceb] # exit(g_vsyscall)
call exit
Note: fixed proc-empty-vm test oopses 5.19.0-28-generic kernel
but this is separate story.
Link: https://lkml.kernel.org/r/Y7h2xvzKLg36DSq8@p183
Fixes: 5bc73bb3451b9 ("proc: test how it holds up with mapping'less process")
Signed-off-by: Alexey Dobriyan <[email protected]>
Reported-by: Mirsad Goran Todorovac <[email protected]>
Tested-by: Mirsad Goran Todorovac <[email protected]>
Cc: <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
|
|
The rename from mm->mmap_sem to mm->mmap_lock was performed in commit
da1c55f1b272 ("mmap locking API: rename mmap_sem to mmap_lock") and commit
c1e8d7c6a7a6 ("map locking API: convert mmap_sem comments"), however some
incorrect comments remain.
This patch simply corrects those comments which are obviously incorrect
within mm itself.
Link: https://lkml.kernel.org/r/33fba04389ab63fc4980e7ba5442f521df6dc657.1673048927.git.lstoakes@gmail.com
Signed-off-by: Lorenzo Stoakes <[email protected]>
Cc: David Hildenbrand <[email protected]>
Cc: Matthew Wilcox <[email protected]>
Cc: Mike Kravetz <[email protected]>
Cc: Muchun Song <[email protected]>
Cc: Vlastimil Babka <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
|
|
Commit 449c796768c9 ("mm: teach release_pages() to take an array of
encoded page pointers too") added the kernel doc comment for
release_pages() on top of 'union release_pages_arg', so making 'make
htmldocs' complains as below:
./include/linux/mm.h:1268: warning: cannot understand function prototype: 'typedef union '
The kernel doc comment for the function is already on top of the
function's definition in mm/swap.c, and the new comment is actually not
for the function but indeed release_pages_arg. Fixing the comment to
reflect the intent would be one option. But, kernel doc cannot parse
the union as below due to the attribute.
./include/linux/mm.h:1272: error: Cannot parse struct or union!
Modify the comment to reflect the intent but do not mark it as a kernel
doc comment.
Link: https://lkml.kernel.org/r/[email protected]
Fixes: 449c796768c9 ("mm: teach release_pages() to take an array of encoded page pointers too")
Signed-off-by: SeongJae Park <[email protected]>
Acked-by: Randy Dunlap <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
|
|
Don't use kernel-doc "/**" notation for non-kernel-doc comments.
Prevents a kernel-doc warning:
lib/win_minmax.c:31: warning: expecting prototype for lib/minmax.c(). Prototype was for minmax_subwin_update() instead
Link: https://lkml.kernel.org/r/[email protected]
Signed-off-by: Randy Dunlap <[email protected]>
Cc: Neal Cardwell <[email protected]>
Cc: Eric Dumazet <[email protected]>
Cc: David S. Miller <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
|
|
Mark kasan_kunit_executing as static, as it is only used within
mm/kasan/report.c.
Link: https://lkml.kernel.org/r/f64778a4683b16a73bba72576f73bf4a2b45a82f.1672794398.git.andreyknvl@google.com
Fixes: c8c7016f50c8 ("kasan: fail non-kasan KUnit tests on KASAN reports")
Reported-by: kernel test robot <[email protected]>
Signed-off-by: Andrey Konovalov <[email protected]>
Reviewed-by: Marco Elver <[email protected]>
Cc: Alexander Potapenko <[email protected]>
Cc: Andrey Ryabinin <[email protected]>
Cc: Dmitry Vyukov <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
|
|
If nilfs2 reads a corrupted disk image and tries to reads a b-tree node
block by calling __nilfs_btree_get_block() against an invalid virtual
block address, it returns -ENOENT because conversion of the virtual block
address to a disk block address fails. However, this return value is the
same as the internal code that b-tree lookup routines return to indicate
that the block being searched does not exist, so functions that operate on
that b-tree may misbehave.
When nilfs_btree_insert() receives this spurious 'not found' code from
nilfs_btree_do_lookup(), it misunderstands that the 'not found' check was
successful and continues the insert operation using incomplete lookup path
data, causing the following crash:
general protection fault, probably for non-canonical address
0xdffffc0000000005: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000028-0x000000000000002f]
...
RIP: 0010:nilfs_btree_get_nonroot_node fs/nilfs2/btree.c:418 [inline]
RIP: 0010:nilfs_btree_prepare_insert fs/nilfs2/btree.c:1077 [inline]
RIP: 0010:nilfs_btree_insert+0x6d3/0x1c10 fs/nilfs2/btree.c:1238
Code: bc 24 80 00 00 00 4c 89 f8 48 c1 e8 03 42 80 3c 28 00 74 08 4c 89
ff e8 4b 02 92 fe 4d 8b 3f 49 83 c7 28 4c 89 f8 48 c1 e8 03 <42> 80 3c
28 00 74 08 4c 89 ff e8 2e 02 92 fe 4d 8b 3f 49 83 c7 02
...
Call Trace:
<TASK>
nilfs_bmap_do_insert fs/nilfs2/bmap.c:121 [inline]
nilfs_bmap_insert+0x20d/0x360 fs/nilfs2/bmap.c:147
nilfs_get_block+0x414/0x8d0 fs/nilfs2/inode.c:101
__block_write_begin_int+0x54c/0x1a80 fs/buffer.c:1991
__block_write_begin fs/buffer.c:2041 [inline]
block_write_begin+0x93/0x1e0 fs/buffer.c:2102
nilfs_write_begin+0x9c/0x110 fs/nilfs2/inode.c:261
generic_perform_write+0x2e4/0x5e0 mm/filemap.c:3772
__generic_file_write_iter+0x176/0x400 mm/filemap.c:3900
generic_file_write_iter+0xab/0x310 mm/filemap.c:3932
call_write_iter include/linux/fs.h:2186 [inline]
new_sync_write fs/read_write.c:491 [inline]
vfs_write+0x7dc/0xc50 fs/read_write.c:584
ksys_write+0x177/0x2a0 fs/read_write.c:637
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
...
</TASK>
This patch fixes the root cause of this problem by replacing the error
code that __nilfs_btree_get_block() returns on block address conversion
failure from -ENOENT to another internal code -EINVAL which means that the
b-tree metadata is corrupted.
By returning -EINVAL, it propagates without glitches, and for all relevant
b-tree operations, functions in the upper bmap layer output an error
message indicating corrupted b-tree metadata via
nilfs_bmap_convert_error(), and code -EIO will be eventually returned as
it should be.
Link: https://lkml.kernel.org/r/[email protected]
Link: https://lkml.kernel.org/r/[email protected]
Signed-off-by: Ryusuke Konishi <[email protected]>
Reported-by: [email protected]
Tested-by: Ryusuke Konishi <[email protected]>
Cc: <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
|
|
Writeback has been implemented for zsmalloc, so this warning no longer
holds.
Link: https://lkml.kernel.org/r/[email protected]
Fixes: 9997bc017549a ("zsmalloc: implement writeback mechanism for zsmalloc")
Suggested-by: Thomas Weißschuh <[email protected]>
Signed-off-by: Nhat Pham <[email protected]>
Reviewed-by: Sergey Senozhatsky <[email protected]>
Cc: Johannes Weiner <[email protected]>
Cc: Jonathan Corbet <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
|
|
Userfaultfd-wp uses pte markers to mark wr-protected pages for both shmem
and hugetlb. Shmem has pre-allocation ready for markers, but hugetlb path
was overlooked.
Doing so by calling huge_pte_alloc() if the initial pgtable walk fails to
find the huge ptep. It's possible that huge_pte_alloc() can fail with
high memory pressure, in that case stop the loop immediately and fail
silently. This is not the most ideal solution but it matches with what we
do with shmem meanwhile it avoids the splat in dmesg.
Link: https://lkml.kernel.org/r/[email protected]
Fixes: 60dfaad65aa9 ("mm/hugetlb: allow uffd wr-protect none ptes")
Signed-off-by: Peter Xu <[email protected]>
Reported-by: James Houghton <[email protected]>
Reviewed-by: Mike Kravetz <[email protected]>
Acked-by: David Hildenbrand <[email protected]>
Acked-by: James Houghton <[email protected]>
Cc: Andrea Arcangeli <[email protected]>
Cc: Axel Rasmussen <[email protected]>
Cc: Muchun Song <[email protected]>
Cc: Nadav Amit <[email protected]>
Cc: <[email protected]> [5.19+]
Signed-off-by: Andrew Morton <[email protected]>
|
|
PMD sharing can only be done in PUD_SIZE-aligned pieces of VMAs; however,
it is possible that HugeTLB VMAs are split without unsharing the PMDs
first.
Without this fix, it is possible to hit the uffd-wp-related WARN_ON_ONCE
in hugetlb_change_protection [1]. The key there is that
hugetlb_unshare_all_pmds will not attempt to unshare PMDs in
non-PUD_SIZE-aligned sections of the VMA.
It might seem ideal to unshare in hugetlb_vm_op_open, but we need to
unshare in both the new and old VMAs, so unsharing in hugetlb_vm_op_split
seems natural.
[1]: https://lore.kernel.org/linux-mm/CADrL8HVeOkj0QH5VZZbRzybNE8CG-tEGFshnA+bG9nMgcWtBSg@mail.gmail.com/
Link: https://lkml.kernel.org/r/[email protected]
Fixes: 6dfeaff93be1 ("hugetlb/userfaultfd: unshare all pmds for hugetlbfs when register wp")
Signed-off-by: James Houghton <[email protected]>
Reviewed-by: Mike Kravetz <[email protected]>
Acked-by: Peter Xu <[email protected]>
Cc: Axel Rasmussen <[email protected]>
Cc: Muchun Song <[email protected]>
Cc: <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
|
|
free_anon_vma_name() is missing a check for anonymous shmem VMA which
leads to a memory leak due to refcount not being dropped. Fix this by
calling anon_vma_name_put() unconditionally. It will free vma->anon_name
whenever it's non-NULL.
Link: https://lkml.kernel.org/r/[email protected]
Fixes: d09e8ca6cb93 ("mm: anonymous shared memory naming")
Signed-off-by: Suren Baghdasaryan <[email protected]>
Suggested-by: David Hildenbrand <[email protected]>
Reviewed-by: David Hildenbrand <[email protected]>
Reported-by: [email protected]
Cc: Hugh Dickins <[email protected]>
Cc: Pasha Tatashin <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
|
|
SHMEM_HUGE_DENY is for emergency use by the admin, to disable allocation
of shmem huge pages if, for example, a dangerous bug is found in their
usage: see "deny" in Documentation/mm/transhuge.rst. An app using
madvise(,,MADV_COLLAPSE) should not be allowed to override it: restore its
precedence over shmem_huge_force.
Restore SHMEM_HUGE_DENY precedence over MADV_COLLAPSE.
Link: https://lkml.kernel.org/r/[email protected]
Fixes: 7c6c6cc4d3a2 ("mm/shmem: add flag to enforce shmem THP in hugepage_vma_check()")
Signed-off-by: Zach O'Keefe <[email protected]>
Suggested-by: Hugh Dickins <[email protected]>
Acked-by: David Hildenbrand <[email protected]>
Cc: Yang Shi <[email protected]>
Cc: <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
|
|
MADV_COLLAPSE acts on one hugepage-aligned/sized region at a time, until
it has collapsed all eligible memory contained within the bounds supplied
by the user.
At the top of each hugepage iteration we (re)lock mmap_lock and
(re)validate the VMA for eligibility and update variables that might have
changed while mmap_lock was dropped. One thing that might occur is that
the VMA could be resized, and as such, we refetch vma->vm_end to make sure
we don't collapse past the end of the VMA's new end.
However, it's possible that when refetching vma->vm_end that we expand the
region acted on by MADV_COLLAPSE if vma->vm_end is greater than size+len
supplied by the user.
The consequence here is that we may attempt to collapse more memory than
requested, possibly yielding either "too much success" or "false failure"
user-visible results. An example of the former is if we MADV_COLLAPSE the
first 4MiB of a 2TiB mmap()'d file, the incorrect refetch would cause the
operation to block for much longer than anticipated as we attempt to
collapse the entire TiB region. An example of the latter is that applying
MADV_COLLPSE to a 4MiB file mapped to the start of a 6MiB VMA will
successfully collapse the first 4MiB, then incorrectly attempt to collapse
the last hugepage-aligned/sized region -- fail (since readahead/page cache
lookup will fail) -- and report a failure to the user.
I don't believe there is a kernel stability concern here as we always
(re)validate the VMA / region accordingly. Also as Hugh mentions, the
user-visible effects are: we try to collapse more memory than requested
by the user, and/or failing an operation that should have otherwise
succeeded. An example is trying to collapse a 4MiB file contained
within a 12MiB VMA.
Don't expand the acted-on region when refetching vma->vm_end.
Link: https://lkml.kernel.org/r/[email protected]
Fixes: 4d24de9425f7 ("mm: MADV_COLLAPSE: refetch vm_end after reacquiring mmap_lock")
Signed-off-by: Zach O'Keefe <[email protected]>
Reported-by: Hugh Dickins <[email protected]>
Cc: Yang Shi <[email protected]>
Cc: <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
|