| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
arch/x86/built-in.o: In function `uv_bios_call':
(.text+0xeba00): undefined reference to `efi_call'
Reported-by: kbuild test robot <[email protected]>
Suggested-by: "H. Peter Anvin" <[email protected]>
Cc: Ingo Molnar <[email protected]>
Reviewed-by: Matt Fleming <[email protected]>
Acked-by: Alex Thorlton <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
The pfn_t type uses an unsigned long to store a pfn + flags value. On a
64-bit platform the upper 12 bits of an unsigned long are never used for
storing the value of a pfn. However, this is not true on highmem
platforms, all 32-bits of a pfn value are used to address a 44-bit
physical address space. A pfn_t needs to store a 64-bit value.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=112211
Fixes: 01c8f1c44b83 ("mm, dax, gpu: convert vm_insert_mixed to pfn_t")
Signed-off-by: Dan Williams <[email protected]>
Reported-by: Stuart Foster <[email protected]>
Reported-by: Julian Margetson <[email protected]>
Tested-by: Julian Margetson <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Mike said:
: CONFIG_UBSAN_ALIGNMENT breaks x86-64 kernel with lockdep enabled, i. e
: kernel with CONFIG_UBSAN_ALIGNMENT fails to load without even any error
: message.
:
: The problem is that ubsan callbacks use spinlocks and might be called
: before lockdep is initialized. Particularly this line in the
: reserve_ebda_region function causes problem:
:
: lowmem = *(unsigned short *)__va(BIOS_LOWMEM_KILOBYTES);
:
: If i put lockdep_init() before reserve_ebda_region call in
: x86_64_start_reservations kernel loads well.
Fix this ordering issue permanently: change lockdep so that it uses
hlists for the hash tables. Unlike a list_head, an hlist_head is in its
initialized state when it is all-zeroes, so lockdep is ready for
operation immediately upon boot - lockdep_init() need not have run.
The patch will also save some memory.
lockdep_init() and lockdep_initialized can be done away with now - a 4.6
patch has been prepared to do this.
Reported-by: Mike Krinkin <[email protected]>
Suggested-by: Mike Krinkin <[email protected]>
Cc: Andrey Ryabinin <[email protected]>
Cc: Ingo Molnar <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
[[email protected]: s/threshhold/threshold/]
Signed-off-by: Vineet Gupta <[email protected]>
Cc: Kirill A. Shutemov <[email protected]>
Cc: Aneesh Kumar K.V <[email protected]>
Cc: Andrea Arcangeli <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
This showed up on ARC when running LMBench bw_mem tests as Overlapping
TLB Machine Check Exception triggered due to STLB entry (2M pages)
overlapping some NTLB entry (regular 8K page).
bw_mem 2m touches a large chunk of vaddr creating NTLB entries. In the
interim khugepaged kicks in, collapsing the contiguous ptes into a
single pmd. pmdp_collapse_flush()->flush_pmd_tlb_range() is called to
flush out NTLB entries for the ptes. This for ARC (by design) can only
shootdown STLB entries (for pmd). The stray NTLB entries cause the
overlap with the subsequent STLB entry for collapsed page. So make
pmdp_collapse_flush() call pte flush interface not pmd flush.
Note that originally all thp flush call sites in generic code called
flush_tlb_range() leaving it to architecture to implement the flush for
pte and/or pmd. Commit 12ebc1581ad11454 changed this by calling a new
opt-in API flush_pmd_tlb_range() which made the semantics more explicit
but failed to distinguish the pte vs pmd flush in generic code, which is
what this patch fixes.
Note that ARC can fixed w/o touching the generic pmdp_collapse_flush()
by defining a ARC version, but that defeats the purpose of generic
version, plus sementically this is the right thing to do.
Fixes STAR 9000961194: LMBench on AXS103 triggering duplicate TLB
exceptions with super pages
Fixes: 12ebc1581ad11454 ("mm,thp: introduce flush_pmd_tlb_range")
Signed-off-by: Vineet Gupta <[email protected]>
Reviewed-by: Aneesh Kumar K.V <[email protected]>
Acked-by: Kirill A. Shutemov <[email protected]>
Cc: Andrea Arcangeli <[email protected]>
Cc: <[email protected]> [4.4]
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
We need to use post-decrement to get percpu_counter_destroy() called on
&wb->stat[0]. Moreover, the pre-decremebt would cause infinite
out-of-bounds accesses if the setup code failed at i==0.
Signed-off-by: Rasmus Villemoes <[email protected]>
Cc: Johannes Weiner <[email protected]>
Cc: Michal Hocko <[email protected]>
Cc: Vladimir Davydov <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
DAX implements split_huge_pmd() by clearing pmd. This simple approach
reduces memory overhead, as we don't need to deposit page table on huge
page mapping to make split_huge_pmd() never-fail. PTE table can be
allocated and populated later on page fault from backing store.
But one side effect is that have to check if pmd is pmd_none() after
split_huge_pmd(). In most places we do this already to deal with
parallel MADV_DONTNEED.
But I found two call sites which is not affected by MADV_DONTNEED (due
down_write(mmap_sem)), but need to have the check to work with DAX
properly.
Signed-off-by: Kirill A. Shutemov <[email protected]>
Cc: Dan Williams <[email protected]>
Cc: Matthew Wilcox <[email protected]>
Cc: Andrea Arcangeli <[email protected]>
Cc: Ross Zwisler <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
The kptr_restrict flag, when set to 1, only prints the kernel address
when the user has CAP_SYSLOG. When it is set to 2, the kernel address
is always printed as zero. When set to 1, this needs to check whether
or not we're in IRQ.
However, when set to 2, this check is unneccessary, and produces
confusing results in dmesg. Thus, only make sure we're not in IRQ when
mode 1 is used, but not mode 2.
[[email protected]: coding-style fixes]
Signed-off-by: Jason A. Donenfeld <[email protected]>
Cc: Rasmus Villemoes <[email protected]>
Cc: Kees Cook <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Add missing kernel-doc notation for function parameter 'gfp_mask' to fix
kernel-doc warning.
mm/filemap.c:1898: warning: No description found for parameter 'gfp_mask'
Signed-off-by: Randy Dunlap <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
When enabling UBSAN_SANITIZE_ALL, the kernel image size gets increased
significantly (~3x). So, it sounds better to have some note in Kconfig.
And, fixed a typo.
Signed-off-by: Yang Shi <[email protected]>
Acked-by: Andrey Ryabinin <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
- Probe errorpath fix for the Altera
- irqchip ofnode pointer added to the DaVinci driver
- controller instance number correction for DaVinci
* tag 'gpio-v4.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: davinci: Fix the number of controllers allocated
gpio: davinci: Add the missing of-node pointer
gpio: gpio-altera: Remove gpiochip on probe failure.
|
|
git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform driver fixes from Darren Hart:
"Just two small fixes for the 4.5-rc cycle:
intel_scu_ipcutil:
- underflow in scu_reg_access()
intel-hid:
- fix incorrect entries in intel_hid_keymap"
* tag 'platform-drivers-x86-v4.5-3' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
intel_scu_ipcutil: underflow in scu_reg_access()
intel-hid: fix incorrect entries in intel_hid_keymap
|
|
Pull networking fixes from David Miller:
1) Fix BPF handling of branch offset adjustmnets on backjumps, from
Daniel Borkmann.
2) Make sure selinux knows about SOCK_DESTROY netlink messages, from
Lorenzo Colitti.
3) Fix openvswitch tunnel mtu regression, from David Wragg.
4) Fix ICMP handling of TCP sockets in syn_recv state, from Eric
Dumazet.
5) Fix SCTP user hmacid byte ordering bug, from Xin Long.
6) Fix recursive locking in ipv6 addrconf, from Subash Abhinov
Kasiviswanathan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
bpf: fix branch offset adjustment on backjumps after patching ctx expansion
vxlan, gre, geneve: Set a large MTU on ovs-created tunnel devices
geneve: Relax MTU constraints
vxlan: Relax MTU constraints
flow_dissector: Fix unaligned access in __skb_flow_dissector when used by eth_get_headlen
of: of_mdio: Add marvell, 88e1145 to whitelist of PHY compatibilities.
selinux: nlmsgtab: add SOCK_DESTROY to the netlink mapping tables
sctp: translate network order to host order when users get a hmacid
enic: increment devcmd2 result ring in case of timeout
tg3: Fix for tg3 transmit queue 0 timed out when too many gso_segs
net:Add sysctl_max_skb_frags
tcp: do not drop syn_recv on all icmp reports
ipv6: fix a lockdep splat
unix: correctly track in-flight fds in sending process user_struct
update be2net maintainers' email addresses
dwc_eth_qos: Reset hardware before PHY start
ipv6: addrconf: Fix recursive spin lock call
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
"A few more minor fixes for rc3:
- One fix to ipoib
- One fix to core sysfs code
- Four patches that resolve an oops found in testing of ocrdma and a
couple other ocrdma issues"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
RDMA/ocrdma: Fixing ocrdma debugfs directory remove
RDMA/ocrdma: Fix pkey_index returned by driver in rq work completion
RDMA/ocrdma: populate max_sge_rd in device attributes
RDMA/ocrdma: Initialize stats resources in the driver before ib device registration.
IB/sysfs: remove unused va_list args
IB/IPoIB: Do not set skb truesize since using one linearskb
|
|
When ctx access is used, the kernel often needs to expand/rewrite
instructions, so after that patching, branch offsets have to be
adjusted for both forward and backward jumps in the new eBPF program,
but for backward jumps it fails to account the delta. Meaning, for
example, if the expansion happens exactly on the insn that sits at
the jump target, it doesn't fix up the back jump offset.
Analysis on what the check in adjust_branches() is currently doing:
/* adjust offset of jmps if necessary */
if (i < pos && i + insn->off + 1 > pos)
insn->off += delta;
else if (i > pos && i + insn->off + 1 < pos)
insn->off -= delta;
First condition (forward jumps):
Before: After:
insns[0] insns[0]
insns[1] <--- i/insn insns[1] <--- i/insn
insns[2] <--- pos insns[P] <--- pos
insns[3] insns[P] `------| delta
insns[4] <--- target_X insns[P] `-----|
insns[5] insns[3]
insns[4] <--- target_X
insns[5]
First case is if we cross pos-boundary and the jump instruction was
before pos. This is handeled correctly. I.e. if i == pos, then this
would mean our jump that we currently check was the patchlet itself
that we just injected. Since such patchlets are self-contained and
have no awareness of any insns before or after the patched one, the
delta is correctly not adjusted. Also, for the second condition in
case of i + insn->off + 1 == pos, means we jump to that newly patched
instruction, so no offset adjustment are needed. That part is correct.
Second condition (backward jumps):
Before: After:
insns[0] insns[0]
insns[1] <--- target_X insns[1] <--- target_X
insns[2] <--- pos <-- target_Y insns[P] <--- pos <-- target_Y
insns[3] insns[P] `------| delta
insns[4] <--- i/insn insns[P] `-----|
insns[5] insns[3]
insns[4] <--- i/insn
insns[5]
Second interesting case is where we cross pos-boundary and the jump
instruction was after pos. Backward jump with i == pos would be
impossible and pose a bug somewhere in the patchlet, so the first
condition checking i > pos is okay only by itself. However, i +
insn->off + 1 < pos does not always work as intended to trigger the
adjustment. It works when jump targets would be far off where the
delta wouldn't matter. But, for example, where the fixed insn->off
before pointed to pos (target_Y), it now points to pos + delta, so
that additional room needs to be taken into account for the check.
This means that i) both tests here need to be adjusted into pos + delta,
and ii) for the second condition, the test needs to be <= as pos
itself can be a target in the backjump, too.
Fixes: 9bac3d6d548e ("bpf: allow extended BPF programs access skb fields")
Signed-off-by: Daniel Borkmann <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
"Just small driver fixups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: colibri-vf50-ts - add missing #include <linux/of.h>
Input: adp5589 - fix row 5 handling for adp5589
Input: edt-ft5x06 - fix setting gain, offset, and threshold via device tree
Input: vmmouse - fix absolute device registration
Input: serio - drop warnings in case of EPROBE_DEFER from serio_find_driver()
Input: cap11xx - add missing of_node_put
Input: sirfsoc-onkey - allow modular build
Input: xpad - remove unused function
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
- PORTS_IMPL workaround for very early ahci controllers is misbehaving
on new systems. Disabled on recent ahci versions.
- Old-style PIO state machine had a horrible locking problem. Don't
know how we've been getting away this far. Fixed.
- Other device specific updates.
* 'for-4.5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: Intel DNV device IDs SATA
libata: fix sff host state machine locking while polling
libata-sff: use WARN instead of BUG on illegal host state machine state
libata: disable forced PORTS_IMPL for >= AHCI 1.3
libata: blacklist a Viking flash model for MWDMA corruption
drivers: ata: wake port before DMA stop for ALPM
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup fixes from Tejun Heo:
- The destruction path of cgroup objects are asynchronous and
multi-staged and some of them ended up destroying parents before
children leading to failures in cpu and memory controllers. Ensure
that parents are always destroyed after children.
- cpuset mm node migration was performed synchronously while holding
threadgroup and cgroup mutexes and the recent threadgroup locking
update resulted in a possible deadlock. The migration is best effort
and shouldn't have been performed under those locks to begin with.
Made asynchronous.
- Minor documentation fix.
* 'for-4.5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
Documentation: cgroup: Fix 'cgroup-legacy' -> 'cgroup-v1'
cgroup: make sure a parent css isn't freed before its children
cgroup: make sure a parent css isn't offlined before its children
cpuset: make mm migration asynchronous
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull workqueue fixes from Tejun Heo:
"Workqueue fixes for v4.5-rc3.
- Remove a spurious triggering of flush dependency warning.
- Officially break local execution guarantee of unbound work items
and add a debug feature to flush out usages which depend on it.
- Work around CPU -> NODE mapping becoming invalid on CPU offline.
The branch is young but pushing out early as stable kernels are being
affected"
* 'for-4.5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: handle NUMA_NO_NODE for unbound pool_workqueue lookup
workqueue: implement "workqueue.debug_force_rr_cpu" debug feature
workqueue: schedule WORK_CPU_UNBOUND work on wq_unbound_cpumask CPUs
Revert "workqueue: make sure delayed work run in local cpu"
workqueue: skip flush dependency checks for legacy workqueues
|
|
When looking up the pool_workqueue to use for an unbound workqueue,
workqueue assumes that the target CPU is always bound to a valid NUMA
node. However, currently, when a CPU goes offline, the mapping is
destroyed and cpu_to_node() returns NUMA_NO_NODE.
This has always been broken but hasn't triggered often enough before
874bbfe600a6 ("workqueue: make sure delayed work run in local cpu").
After the commit, workqueue forcifully assigns the local CPU for
delayed work items without explicit target CPU to fix a different
issue. This widens the window where CPU can go offline while a
delayed work item is pending causing delayed work items dispatched
with target CPU set to an already offlined CPU. The resulting
NUMA_NO_NODE mapping makes workqueue try to queue the work item on a
NULL pool_workqueue and thus crash.
While 874bbfe600a6 has been reverted for a different reason making the
bug less visible again, it can still happen. Fix it by mapping
NUMA_NO_NODE to the default pool_workqueue from unbound_pwq_by_node().
This is a temporary workaround. The long term solution is keeping CPU
-> NODE mapping stable across CPU off/online cycles which is being
worked on.
Signed-off-by: Tejun Heo <[email protected]>
Reported-by: Mike Galbraith <[email protected]>
Cc: Tang Chen <[email protected]>
Cc: Rafael J. Wysocki <[email protected]>
Cc: Len Brown <[email protected]>
Cc: [email protected]
Link: http://lkml.kernel.org/g/[email protected]
Link: http://lkml.kernel.org/g/[email protected]
|
|
Adding Intel codename DNV platform device IDs for SATA.
Signed-off-by: Alexandra Yates <[email protected]>
Signed-off-by: Tejun Heo <[email protected]>
Cc: [email protected]
|
|
David Wragg says:
====================
Set a large MTU on ovs-created tunnel devices
Prior to 4.3, openvswitch tunnel vports (vxlan, gre and geneve) could
transmit vxlan packets of any size, constrained only by the ability to
send out the resulting packets. 4.3 introduced netdevs corresponding
to tunnel vports. These netdevs have an MTU, which limits the size of
a packet that can be successfully encapsulated. The default MTU
values are low (1500 or less), which is awkwardly small in the context
of physical networks supporting jumbo frames, and leads to a
conspicuous change in behaviour for userspace.
This patch series sets the MTU on openvswitch-created netdevs to be
the relevant maximum (i.e. the maximum IP packet size minus any
relevant overhead), effectively restoring the behaviour prior to 4.3.
Where relevant, the limits on MTU values that can be directly set on
the netdevs are also relaxed.
Changes in v2:
* Extend to all openvswitch tunnel types, i.e. gre and geneve as well
* Use IP_MAX_MTU
Changes in v3:
* Fix block comment style
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
Prior to 4.3, openvswitch tunnel vports (vxlan, gre and geneve) could
transmit vxlan packets of any size, constrained only by the ability to
send out the resulting packets. 4.3 introduced netdevs corresponding
to tunnel vports. These netdevs have an MTU, which limits the size of
a packet that can be successfully encapsulated. The default MTU
values are low (1500 or less), which is awkwardly small in the context
of physical networks supporting jumbo frames, and leads to a
conspicuous change in behaviour for userspace.
Instead, set the MTU on openvswitch-created netdevs to be the relevant
maximum (i.e. the maximum IP packet size minus any relevant overhead),
effectively restoring the behaviour prior to 4.3.
Signed-off-by: David Wragg <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Allow the MTU of geneve devices to be set to large values, in order to
exploit underlying networks with larger frame sizes.
GENEVE does not have a fixed encapsulation overhead (an openvswitch
rule can add variable length options), so there is no relevant maximum
MTU to enforce. A maximum of IP_MAX_MTU is used instead.
Encapsulated packets that are too big for the underlying network will
get dropped on the floor.
Signed-off-by: David Wragg <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Allow the MTU of vxlan devices without an underlying device to be set
to larger values (up to a maximum based on IP packet limits and vxlan
overhead).
Previously, their MTUs could not be set to higher than the
conventional ethernet value of 1500. This is a very arbitrary value
in the context of vxlan, and prevented vxlan devices from being able
to take advantage of jumbo frames etc.
The default MTU remains 1500, for compatibility.
Signed-off-by: David Wragg <[email protected]>
Acked-by: Roopa Prabhu <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Driver only needs to allocate for [ngpio / 32] controllers,
as each controller handles 32 gpios. But the current driver
allocates for ngpio of which the extra allocated are unused.
Fix it be registering only the required number of controllers.
Signed-off-by: Lokesh Vutla <[email protected]>
Signed-off-by: Keerthy <[email protected]>
Reviewed-by: Grygorii Strashko <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
Currently the first parameter of irq_domain_add_legacy is NULL.
irq_find_host function returns NULL when we do not populate the of_node
and hence irq_of_parse_and_map call fails whenever we want to request a
gpio irq. This fixes the request_irq failures for gpio interrupts.
Signed-off-by: Keerthy <[email protected]>
Reviewed-by: Grygorii Strashko <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module fixes from Rusty Russell:
"Fix for async_probe module param added in 4.3 (clearly not widely used
yet), and a much more interesting kallsyms race which has been around
approximately forever. This fix is more invasive, and will require
some care in backporting, but I hated all the bandaids I could think
of, so...
There are some more coming, which are only for breakages introduced
this cycle (livepatch), but wanted these in now"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
modules: fix longstanding /proc/kallsyms vs module insertion race.
module: wrapper for symbol name.
modules: fix modparam async_probe request
|
|
drivers/input/touchscreen/colibri-vf50-ts.c: In function ‘vf50_ts_probe’:
drivers/input/touchscreen/colibri-vf50-ts.c:302: error: implicit declaration of function ‘of_property_read_u32’
Signed-off-by: Geert Uytterhoeven <[email protected]>
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
The adp5589 has row 5, don't skip it when creating the GPIO mapping.
Otherwise the pin gets reserved as used and it is not possible to use it as
a GPIO.
Signed-off-by: Lars-Peter Clausen <[email protected]>
Acked-by: Michael Hennerich <[email protected]>
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
A recent patch broke parsing the gain, offset, and threshold parameters
from device tree. Instead of setting the cached values and writing them
to the correct registers during probe, it would write the values from DT
into the register address variables and never write them to the chip
during normal operation.
Fixes: 2e23b7a96372 ("Input: edt-ft5x06 - use generic properties API")
Signed-off-by: Philipp Zabel <[email protected]>
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
Workqueue used to guarantee local execution for work items queued
without explicit target CPU. The guarantee is gone now which can
break some usages in subtle ways. To flush out those cases, this
patch implements a debug feature which forces round-robin CPU
selection for all such work items.
The debug feature defaults to off and can be enabled with a kernel
parameter. The default can be flipped with a debug config option.
If you hit this commit during bisection, please refer to 041bd12e272c
("Revert "workqueue: make sure delayed work run in local cpu"") for
more information and ping me.
Signed-off-by: Tejun Heo <[email protected]>
|
|
WORK_CPU_UNBOUND work items queued to a bound workqueue always run
locally. This is a good thing normally, but not when the user has
asked us to keep unbound work away from certain CPUs. Round robin
these to wq_unbound_cpumask CPUs instead, as perturbation avoidance
trumps performance.
tj: Cosmetic and comment changes. WARN_ON_ONCE() dropped from empty
(wq_unbound_cpumask AND cpu_online_mask). If we want that, it
should be done when config changes.
Signed-off-by: Mike Galbraith <[email protected]>
Signed-off-by: Tejun Heo <[email protected]>
|
|
This reverts commit 874bbfe600a660cba9c776b3957b1ce393151b76.
Workqueue used to implicity guarantee that work items queued without
explicit CPU specified are put on the local CPU. Recent changes in
timer broke the guarantee and led to vmstat breakage which was fixed
by 176bed1de5bf ("vmstat: explicitly schedule per-cpu work on the CPU
we need it to run on").
vmstat is the most likely to expose the issue and it's quite possible
that there are other similar problems which are a lot more difficult
to trigger. As a preventive measure, 874bbfe600a6 ("workqueue: make
sure delayed work run in local cpu") was applied to restore the local
CPU guarnatee. Unfortunately, the change exposed a bug in timer code
which got fixed by 22b886dd1018 ("timers: Use proper base migration in
add_timer_on()"). Due to code restructuring, the commit couldn't be
backported beyond certain point and stable kernels which only had
874bbfe600a6 started crashing.
The local CPU guarantee was accidental more than anything else and we
want to get rid of it anyway. As, with the vmstat case fixed,
874bbfe600a6 is causing more problems than it's fixing, it has been
decided to take the chance and officially break the guarantee by
reverting the commit. A debug feature will be added to force foreign
CPU assignment to expose cases relying on the guarantee and fixes for
the individual cases will be backported to stable as necessary.
Signed-off-by: Tejun Heo <[email protected]>
Fixes: 874bbfe600a6 ("workqueue: make sure delayed work run in local cpu")
Link: http://lkml.kernel.org/g/[email protected]
Cc: [email protected]
Cc: Mike Galbraith <[email protected]>
Cc: Henrique de Moraes Holschuh <[email protected]>
Cc: Daniel Bilik <[email protected]>
Cc: Jan Kara <[email protected]>
Cc: Shaohua Li <[email protected]>
Cc: Sasha Levin <[email protected]>
Cc: Ben Hutchings <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: Daniel Bilik <[email protected]>
Cc: Jiri Slaby <[email protected]>
Cc: Michal Hocko <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
"This fixes the following issues:
API:
- Fix async algif_skcipher, it was broken by recent fixes.
- Fix potential race condition in algif_skcipher with ctx.
- Fix potential memory corruption in algif_skcipher.
- Add missing lock to crypto_user when doing an alg dump.
Drivers:
- marvell/cesa was testing the wrong variable for NULL after
allocation.
- Fix potential double-free in atmel-sha.
- Fix illegal call to sleepin function from atomic context in
atmel-sha"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: marvell/cesa - fix test in mv_cesa_dev_dma_init()
crypto: atmel-sha - remove calls of clk_prepare() from atomic contexts
crypto: atmel-sha - fix atmel_sha_remove()
crypto: algif_skcipher - Do not set MAY_BACKLOG on the async path
crypto: algif_skcipher - Do not dereference ctx without socket lock
crypto: algif_skcipher - Do not assume that req is unchanged
crypto: user - lock crypto_alg_list on alg dump
|
|
Long ago, Dave Jones complained about CONFIG_LOCALVERSION_AUTO:
"I don't use the auto config, because I end up filling up /boot unless
I go through and clean them out by hand every time I install a new one
(which I do probably a dozen or so times a day). Is there some easy
way to prune old builds I'm missing?"
To which Bruce replied:
"I run this by hand every now and then. I'm probably doing it all wrong"
And if he is running it wrong, then so am I - because I've been using
this script ever since. It is true that CONFIG_LOCALVERSION_AUTO easily
ends up filling your /boot partition if you don't clean up old versions
regularly, and this script helps make that easier.
Checked with Bruce to see that it's fine to add this to the kernel
scripts. Maybe people will come up with enhancements, but more
importantly, this way I won't misplace this script whenever I install a
new machine and start doing custom kernels for it.
Signed-off-by: Linus Torvalds <[email protected]>
|
|
eth_get_headlen
This patch fixes an issue with unaligned accesses when using
eth_get_headlen on a page that was DMA aligned instead of being IP aligned.
The fact is when trying to check the length we don't need to be looking at
the flow label so we can reorder the checks to first check if we are
supposed to gather the flow label and then make the call to actually get
it.
v2: Updated path so that either STOP_AT_FLOW_LABEL or KEY_FLOW_LABEL can
cause us to check for the flow label.
Reported-by: Sowmini Varadhan <[email protected]>
Signed-off-by: Alexander Duyck <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Commit ae461131960b ("of: of_mdio: Add a whitelist of PHY
compatibilities.") missed one compatible string used in in-tree DTBs:
in OCTEON, for selected boards, the kernel DTB pruning code will overwrite
the DTB compatible string with "marvell,88e1145", which is missing
from the whitelist. Add it.
The patch fixes broken networking on EdgeRouter Lite.
Fixes: ae461131960b ("of: of_mdio: Add a whitelist of PHY compatibilities.")
Signed-off-by: Aaro Koskinen <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Without this, using SOCK_DESTROY in enforcing mode results in:
SELinux: unrecognized netlink message type=21 for sclass=32
Signed-off-by: Lorenzo Colitti <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Commit ed5a377d87dc ("sctp: translate host order to network order when
setting a hmacid") corrected the hmacid byte-order when setting a hmacid.
but the same issue also exists on getting a hmacid.
We fix it by changing hmacids to host order when users get them with
getsockopt.
Fixes: Commit ed5a377d87dc ("sctp: translate host order to network order when setting a hmacid")
Signed-off-by: Xin Long <[email protected]>
Acked-by: Marcelo Ricardo Leitner <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Firmware posts the devcmd result in result ring. In case of timeout, driver
does not increment the current result pointer and firmware could post the
result after timeout has occurred. During next devcmd, driver would be
reading the result of previous devcmd.
Fix this by incrementing result even in case of timeout.
Fixes: 373fb0873d43 ("enic: add devcmd2")
Signed-off-by: Sandeep Pillai <[email protected]>
Signed-off-by: Govindarajulu Varadarajan <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
tg3_tso_bug() can hit a condition where the entire tx ring is not big
enough to segment the GSO packet. For example, if MSS is very small,
gso_segs can exceed the tx ring size. When we hit the condition, it
will cause tx timeout.
tg3_tso_bug() is called to handle TSO and DMA hardware bugs.
For TSO bugs, if tg3_tso_bug() cannot succeed, we have to drop the packet.
For DMA bugs, we can still fall back to linearize the SKB and let the
hardware transmit the TSO packet.
This patch adds a function tg3_tso_bug_gso_check() to check if there
are enough tx descriptors for GSO before calling tg3_tso_bug().
The caller will then handle the error appropriately - drop or
lineraize the SKB.
v2: Corrected patch description to avoid confusion.
Signed-off-by: Siva Reddy Kallam <[email protected]>
Signed-off-by: Michael Chan <[email protected]>
Acked-by: Prashant Sreedharan <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Devices may have limits on the number of fragments in an skb they support.
Current codebase uses a constant as maximum for number of fragments one
skb can hold and use.
When enabling scatter/gather and running traffic with many small messages
the codebase uses the maximum number of fragments and may thereby violate
the max for certain devices.
The patch introduces a global variable as max number of fragments.
Signed-off-by: Hans Westgaard Ry <[email protected]>
Reviewed-by: Håkon Bugge <[email protected]>
Acked-by: Eric Dumazet <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Petr Novopashenniy reported that ICMP redirects on SYN_RECV sockets
were leading to RST.
This is of course incorrect.
A specific list of ICMP messages should be able to drop a SYN_RECV.
For instance, a REDIRECT on SYN_RECV shall be ignored, as we do
not hold a dst per SYN_RECV pseudo request.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=111751
Fixes: 079096f103fa ("tcp/dccp: install syn_recv requests into ehash table")
Reported-by: Petr Novopashenniy <[email protected]>
Signed-off-by: Eric Dumazet <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Pull KVM fixes from Paolo Bonzini:
"KVM-ARM fixes, mostly coming from the PMU work"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
arm64: KVM: Fix guest dead loop when register accessor returns false
arm64: KVM: Fix comments of the CP handler
arm64: KVM: Fix wrong use of the CPSR MODE mask for 32bit guests
arm64: KVM: Obey RES0/1 reserved bits when setting CPTR_EL2
arm64: KVM: Fix AArch64 guest userspace exception injection
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fix from Mark Brown:
"A single revert back to v4.4 endianness handling.
Commit 29bb45f25ff3 ("regmap-mmio: Use native endianness for
read/write") attempted to fix some long standing bugs in the MMIO
implementation for big endian systems caused by duplicate byte
swapping in both regmap and readl()/writel(). Sadly the fix makes
things worse rather than better, so revert it for now"
* tag 'regmap-fix-v4.5-big-endian' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: mmio: Revert to v4.4 endianness handling
|
|
Fix the doubled "started" and tidy up the following sentences.
Signed-off-by: Masahiro Yamada <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Silence lockdep false positive about rcu_dereference() being
used in the wrong context.
First one should use rcu_dereference_protected() as we own the spinlock.
Second one should be a normal assignation, as no barrier is needed.
Fixes: 18367681a10bd ("ipv6 flowlabel: Convert np->ipv6_fl_list to RCU.")
Reported-by: Dave Jones <[email protected]>
Signed-off-by: Eric Dumazet <[email protected]>
Acked-by: Hannes Frederic Sowa <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The commit referenced in the Fixes tag incorrectly accounted the number
of in-flight fds over a unix domain socket to the original opener
of the file-descriptor. This allows another process to arbitrary
deplete the original file-openers resource limit for the maximum of
open files. Instead the sending processes and its struct cred should
be credited.
To do so, we add a reference counted struct user_struct pointer to the
scm_fp_list and use it to account for the number of inflight unix fds.
Fixes: 712f4aad406bb1 ("unix: properly account for FDs passed over unix sockets")
Reported-by: David Herrmann <[email protected]>
Cc: David Herrmann <[email protected]>
Cc: Willy Tarreau <[email protected]>
Cc: Linus Torvalds <[email protected]>
Suggested-by: Linus Torvalds <[email protected]>
Signed-off-by: Hannes Frederic Sowa <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into kvm-master
KVM/ARM fixes for v4.5-rc2
A few random fixes, mostly coming from the PMU work by Shannon:
- fix for injecting faults coming from the guest's userspace
- cleanup for our CPTR_EL2 accessors (reserved bits)
- fix for a bug impacting perf (user/kernel discrimination)
- fix for a 32bit sysreg handling bug
|