| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Currently the sun8i thermal driver will fail to probe if any of the
thermal zones it is registering fails to register with the thermal core.
Since we currently do not define any trip points for the GPU thermal
zones on at least A64 or H5 this means that we have no thermal support
on these platforms:
[ 1.698703] thermal_sys: Failed to find 'trips' node
[ 1.698707] thermal_sys: Failed to find trip points for thermal-sensor id=1
even though the main CPU thermal zone on both SoCs is fully configured.
This does not seem ideal, while we may not be able to use all the zones
it seems better to have those zones which are usable be operational.
Instead just carry on registering zones if we get any non-deferral
error, allowing use of those zones which are usable.
This means that we also need to update the interrupt handler to not
attempt to notify the core for events on zones which we have not
registered, I didn't see an ability to mask individual interrupts and
I would expect that interrupts would still be indicated in the ISR even
if they were masked.
Reviewed-by: Vasily Khoruzhick <[email protected]>
Acked-by: Jernej Skrabec <[email protected]>
Signed-off-by: Mark Brown <[email protected]>
Signed-off-by: Daniel Lezcano <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Add support for the thermal sensor found in H616 SoCs, is the same as
the H6 thermal sensor controller, but with four sensors.
Also the registers readings are wrong, unless a bit in the first SYS_CFG
register cleared, so set exercise the SRAM regmap to take care of that.
Signed-off-by: Martin Botka <[email protected]>
Signed-off-by: Andre Przywara <[email protected]>
Acked-by: Vasily Khoruzhick <[email protected]>
Signed-off-by: Daniel Lezcano <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
The Allwinner H616 SoC needs to clear a bit in one register in the SRAM
controller, to report reasonable temperature values. On reset, bit 16 in
register 0x3000000 is set, which leads to the driver reporting
temperatures around 200C. Clearing this bit brings the values down to the
expected range. The BSP code does a one-time write in U-Boot, with a
comment just mentioning the effect on the THS, but offering no further
explanation.
To not rely on firmware to set things up for us, add code that queries
the SRAM controller device via a DT phandle link, then clear just this
single bit.
Signed-off-by: Andre Przywara <[email protected]>
Acked-by: Vasily Khoruzhick <[email protected]>
Signed-off-by: Daniel Lezcano <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
The H616 SoC resembles the H6 thermal sensor controller, with a few
changes like four sensors.
Extend sun50i_h6_ths_calibrate() function to support calibration of
these sensors.
Co-developed-by: Martin Botka <[email protected]>
Signed-off-by: Martin Botka <[email protected]>
Signed-off-by: Maksim Kiselev <[email protected]>
Reviewed-by: Andre Przywara <[email protected]>
Signed-off-by: Andre Przywara <[email protected]>
Reviewed-by: Jernej Skrabec <[email protected]>
Acked-by: Vasily Khoruzhick <[email protected]>
Signed-off-by: Daniel Lezcano <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
So far we were ORing in some "unknown" value into the THS control
register on the Allwinner H6. This part of the register is not explained
in the H6 manual, but the H616 manual details those bits, and on closer
inspection the THS IP blocks in both SoCs seem very close:
- The BSP code for both SoCs writes the same values into THS_CTRL.
- The reset values of at least the first three registers are the same.
Replace the "unknown" value with its proper meaning: "acquire time",
most probably the sample part of the sample & hold circuit of the ADC,
according to its explanation in the H616 manual.
No functional change, just a macro rename and adjustment.
Signed-off-by: Andre Przywara <[email protected]>
Reviewed-by: Jernej Skrabec <[email protected]>
Acked-by: Vasily Khoruzhick <[email protected]>
Signed-off-by: Daniel Lezcano <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
This controller is similar to the H6, but covers four sensors and uses
slightly different calibration methods.
Also the H616 requires to poke a bit in the SYS_CFG register range for
correct operation, so add a phandle property to point there.
Signed-off-by: Martin Botka <[email protected]>
Signed-off-by: Andre Przywara <[email protected]>
Reviewed-by: Krzysztof Kozlowski <[email protected]>
Acked-by: Vasily Khoruzhick <[email protected]>
Signed-off-by: Daniel Lezcano <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
The Allwinner H616 SoC contains a mysterious bit at register offset 0x0
in the SRAM control block. If bit 16 is set (the reset value), the
temperature readings of the THS are way off, leading to reports about
200C, at normal ambient temperatures. Clearing this bits brings the
reported values down to the expected values.
The BSP code clears this bit in firmware (U-Boot), and has an explicit
comment about this, but offers no real explanation.
Experiments in U-Boot show that register 0x0 has no effect on the SRAM C
visibility: all tested bit settings still allow full read and write
access by the CPU to the whole of SRAM C. Only bit 24 of the register at
offset 0x4 makes all of SRAM C inaccessible by the CPU. So modelling
the THS switch functionality as an SRAM region would not reflect reality.
Since we should not rely on firmware settings, allow other code (the THS
driver) to access this register, by exporting it through the already
existing regmap. This mimics what we already do for the LDO control and
the EMAC register.
To avoid concurrent accesses to the same register at the same time, by
the SRAM switch code and the regmap code, use the same lock to protect
the access. The regmap subsystem allows to use an existing lock, so we
just need to hook in there.
Signed-off-by: Andre Przywara <[email protected]>
Reviewed-by: Jernej Skrabec <[email protected]>
Signed-off-by: Daniel Lezcano <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
The number of fsl,tmu-range entries vary among the several NXP SoCs.
- lx2160a has two fsl,tmu-range entries (fsl,qoriq-tmu compatible)
- imx8mq has four fsl,tmu-range entries. (fsl,imx8mq-tmu compatible)
- imx93 has seven fsl,tmu-range entries. (fsl,qoriq-tmu compatible)
Change minItems and maxItems accordingly.
This fixes the following schema warning:
imx93-11x11-evk.dtb: tmu@44482000: fsl,tmu-range: 'oneOf' conditional failed, one must be fixed:
[2147483866, 2147483881, 2147483906, 2147483946, 2147484006, 2147484071, 2147484086] is too long
Signed-off-by: Fabio Estevam <[email protected]>
Reviewed-by: Rob Herring <[email protected]>
Signed-off-by: Daniel Lezcano <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
There is never a need to have a space before a TAB, but it hurts the
eyes of vim users.
Signed-off-by: Geert Uytterhoeven <[email protected]>
Signed-off-by: Daniel Lezcano <[email protected]>
Link: https://lore.kernel.org/r/480478a53fd42621e97b2db36e181903cc0f53e3.1708001426.git.geert+renesas@glider.be
|
|
Reading thermal sensor on mt7986 devices returns invalid temperature:
bpi-r3 ~ # cat /sys/class/thermal/thermal_zone0/temp
-274000
Fix this by adding missing members in mtk_thermal_data struct which were
used in mtk_thermal_turn_on_buffer after commit 33140e668b10.
Cc: [email protected]
Fixes: 33140e668b10 ("thermal/drivers/mediatek: Control buffer enablement tweaks")
Signed-off-by: Frank Wunderlich <[email protected]>
Reviewed-by: Markus Schneider-Pargmann <[email protected]>
Reviewed-by: Daniel Golle <[email protected]>
Tested-by: Daniel Golle <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Signed-off-by: Daniel Lezcano <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
handling path
If devm_krealloc() fails, then 'efuse' is leaking.
So free it to avoid a leak.
Fixes: f5f633b18234 ("thermal/drivers/mediatek: Add the Low Voltage Thermal Sensor driver")
Signed-off-by: Christophe JAILLET <[email protected]>
Reviewed-by: Matthias Brugger <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Signed-off-by: Daniel Lezcano <[email protected]>
Link: https://lore.kernel.org/r/481d345233862d58c3c305855a93d0dbc2bbae7e.1706431063.git.christophe.jaillet@wanadoo.fr
|
|
We already have kprobe and fentry benchmarks. Let's add kretprobe and
fexit ones for completeness.
Signed-off-by: Andrii Nakryiko <[email protected]>
Signed-off-by: Daniel Borkmann <[email protected]>
Acked-by: Jiri Olsa <[email protected]>
Link: https://lore.kernel.org/bpf/[email protected]
|
|
ioremap_page_range() should be used for ranges within vmalloc range only.
The vmalloc ranges are allocated by get_vm_area(). PCI has "resource"
allocator that manages PCI_IOBASE, IO_SPACE_LIMIT address range, hence
introduce vmap_page_range() to be used exclusively to map pages
in PCI address space.
Fixes: 3e49a866c9dc ("mm: Enforce VM_IOREMAP flag and range in ioremap_page_range.")
Reported-by: Miguel Ojeda <[email protected]>
Signed-off-by: Alexei Starovoitov <[email protected]>
Signed-off-by: Daniel Borkmann <[email protected]>
Reviewed-by: Christoph Hellwig <[email protected]>
Tested-by: Miguel Ojeda <[email protected]>
Link: https://lore.kernel.org/bpf/CANiq72ka4rir+RTN2FQoT=Vvprp_Ao-CvoYEkSNqtSY+RZj+AA@mail.gmail.com
|
|
'ras/edac-amd-atl' into edac-updates-for-v6.9
* ras/edac-drivers:
EDAC/i10nm: Add Intel Grand Ridge micro-server support
EDAC/igen6: Add one more Intel Alder Lake-N SoC support
* ras/edac-misc:
EDAC/versal: Convert to platform remove callback returning void
EDAC/versal: Make the bit position of injected errors configurable
EDAC/synopsys: Convert to devm_platform_ioremap_resource()
* ras/edac-amd-atl:
RAS/AMD/FMPM: Fix off by one when unwinding on error
RAS/AMD/FMPM: Add debugfs interface to print record entries
RAS/AMD/FMPM: Save SPA values
RAS: Export helper to get ras_debugfs_dir
RAS/AMD/ATL: Fix bit overflow in denorm_addr_df4_np2()
RAS: Introduce a FRU memory poison manager
RAS/AMD/ATL: Add MI300 row retirement support
Documentation: Move RAS section to admin-guide
RAS/AMD/ATL: Add MI300 DRAM to normalized address translation support
RAS/AMD/ATL: Fix array overflow in get_logical_coh_st_fabric_id_mi300()
RAS/AMD/ATL: Add MI300 support
Documentation: RAS: Add index and address translation section
EDAC/amd64: Use new AMD Address Translation Library
RAS: Introduce AMD Address Translation Library
Signed-off-by: Borislav Petkov (AMD) <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm into pm
Merge OPP (operating performance points) updates for 6.9 from Viresh
Kumar:
"- Fix couple of warnings related to W=1 builds. (Viresh Kumar).
- Move Move dev_pm_opp_{init|free}_cpufreq_table() to pm_opp.h (Viresh Kumar).
- Extend dev_pm_opp_data with turbo support (Sibi Sankar).
- dt-bindings: drop maxItems from inner items (David Heidelberg)."
* tag 'opp-updates-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
dt-bindings: opp: drop maxItems from inner items
OPP: debugfs: Fix warning around icc_get_name()
OPP: debugfs: Fix warning with W=1 builds
cpufreq: Move dev_pm_opp_{init|free}_cpufreq_table() to pm_opp.h
OPP: Extend dev_pm_opp_data with turbo support
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v6.9
This has been quite a small release, there's a lot of driver specific
cleanups and minor enhancements but hardly anything on the core and only
one new driver. Highlights include:
- SoundWire support for AMD ACP 6.3 systems.
- Support for reporting version information for AVS firmware.
- Support DSPless mode for Intel Soundwire systems.
- Support for configuring CS35L56 amplifiers using EFI calibration
data.
- Log which component is being operated on as part of power management
trace events.
- Support for Microchip SAM9x7, NXP i.MX95 and Qualcomm WCD939x
|
|
Merge Enery Model changes for 6.9-rc1:
- Allow the Energy Model to be updated dynamically (Lukasz Luba).
* pm-em: (24 commits)
PM: EM: Fix nr_states warnings in static checks
Documentation: EM: Update with runtime modification design
PM: EM: Add em_dev_compute_costs()
PM: EM: Remove old table
PM: EM: Change debugfs configuration to use runtime EM table data
drivers/thermal/devfreq_cooling: Use new Energy Model interface
drivers/thermal/cpufreq_cooling: Use new Energy Model interface
powercap/dtpm_devfreq: Use new Energy Model interface to get table
powercap/dtpm_cpu: Use new Energy Model interface to get table
PM: EM: Optimize em_cpu_energy() and remove division
PM: EM: Support late CPUs booting and capacity adjustment
PM: EM: Add performance field to struct em_perf_state and optimize
PM: EM: Add em_perf_state_from_pd() to get performance states table
PM: EM: Introduce em_dev_update_perf_domain() for EM updates
PM: EM: Add functions for memory allocations for new EM tables
PM: EM: Use runtime modified EM for CPUs energy estimation in EAS
PM: EM: Introduce runtime modifiable table
PM: EM: Split the allocation and initialization of the EM table
PM: EM: Check if the get_cost() callback is present in em_compute_costs()
PM: EM: Introduce em_compute_costs()
...
|
|
Merge power capping changes and power management utilities updates for
6.9-rc1:
- Address multiple issues in the TPMI RAPL driver and add support for
new platforms (Lunar Lake-M, Arrow Lake) to Intel RAPL (Zhang Rui).
- Fix freq_qos_add_request() return value check in dtpm_cpu (Daniel
Lezcano).
- Fix kernel-doc for dtpm_create_hierarchy() (Yang Li).
- Fix file leak in get_pkg_num() in x86_energy_perf_policy (Samasth
Norway Ananda).
- Fix cpupower-frequency-info.1 man page typo (Jan Kratochvil).
* pm-powercap:
powercap: dtpm: Fix kernel-doc for dtpm_create_hierarchy() function
powercap: dtpm_cpu: Fix error check against freq_qos_add_request()
powercap: intel_rapl: Add support for Arrow Lake
powercap: intel_rapl: Add support for Lunar Lake-M paltform
powercap: intel_rapl_tpmi: Fix System Domain probing
powercap: intel_rapl_tpmi: Fix a register bug
powercap: intel_rapl: Fix locking in TPMI RAPL
powercap: intel_rapl: Fix a NULL pointer dereference
* pm-tools:
Fix cpupower-frequency-info.1 man page typo
tools/power x86_energy_perf_policy: Fix file leak in get_pkg_num()
|
|
Merge cpuidle updates for 6.9-rc1:
- Prevent the haltpoll cpuidle governor from shrinking guest
poll_limit_ns below grow_start (Parshuram Sangle).
- Avoid potential overflow in integer multiplication when computing
cpuidle state parameters (C Cheng).
- Adjust MWAIT hint target C-state computation in the ACPI cpuidle
driver and in intel_idle to return a correct value for C0 (He
Rongguang).
* pm-cpuidle:
cpuidle: ACPI/intel: fix MWAIT hint target C-state computation
cpuidle: Avoid potential overflow in integer multiplication
cpuidle: haltpoll: do not shrink guest poll_limit_ns below grow_start
|
|
KVM Xen and pfncache changes for 6.9:
- Rip out the half-baked support for using gfn_to_pfn caches to manage pages
that are "mapped" into guests via physical addresses.
- Add support for using gfn_to_pfn caches with only a host virtual address,
i.e. to bypass the "gfn" stage of the cache. The primary use case is
overlay pages, where the guest may change the gfn used to reference the
overlay page, but the backing hva+pfn remains the same.
- Add an ioctl() to allow mapping Xen's shared_info page using an hva instead
of a gpa, so that userspace doesn't need to reconfigure and invalidate the
cache/mapping if the guest changes the gpa (but userspace keeps the resolved
hva the same).
- When possible, use a single host TSC value when computing the deadline for
Xen timers in order to improve the accuracy of the timer emulation.
- Inject pending upcall events when the vCPU software-enables its APIC to fix
a bug where an upcall can be lost (and to follow Xen's behavior).
- Fall back to the slow path instead of warning if "fast" IRQ delivery of Xen
events fails, e.g. if the guest has aliased xAPIC IDs.
- Extend gfn_to_pfn_cache's mutex to cover (de)activation (in addition to
refresh), and drop a now-redundant acquisition of xen_lock (that was
protecting the shared_info cache) to fix a deadlock due to recursively
acquiring xen_lock.
|
|
KVM x86 PMU changes for 6.9:
- Fix several bugs where KVM speciously prevents the guest from utilizing
fixed counters and architectural event encodings based on whether or not
guest CPUID reports support for the _architectural_ encoding.
- Fix a variety of bugs in KVM's emulation of RDPMC, e.g. for "fast" reads,
priority of VMX interception vs #GP, PMC types in architectural PMUs, etc.
- Add a selftest to verify KVM correctly emulates RDMPC, counter availability,
and a variety of other PMC-related behaviors that depend on guest CPUID,
i.e. are difficult to validate via KVM-Unit-Tests.
- Zero out PMU metadata on AMD if the virtual PMU is disabled to avoid wasting
cycles, e.g. when checking if a PMC event needs to be synthesized when
skipping an instruction.
- Optimize triggering of emulated events, e.g. for "count instructions" events
when skipping an instruction, which yields a ~10% performance improvement in
VM-Exit microbenchmarks when a vPMU is exposed to the guest.
- Tighten the check for "PMI in guest" to reduce false positives if an NMI
arrives in the host while KVM is handling an IRQ VM-Exit.
|
|
KVM VMX changes for 6.9:
- Fix a bug where KVM would report stale/bogus exit qualification information
when exiting to userspace due to an unexpected VM-Exit while the CPU was
vectoring an exception.
- Add a VMX flag in /proc/cpuinfo to report 5-level EPT support.
- Clean up the logic for massaging the passthrough MSR bitmaps when userspace
changes its MSR filter.
|
|
Merge cpufreq changes for 6.9-rc1:
- Enable preferred core support in the amd-pstate cpufreq driver (Meng
Li).
- Fix min_perf assignment in amd_pstate_adjust_perf() and make the
min/max limit perf values in amd-pstate always stay within the
(highest perf, lowest perf) range (Tor Vic, Meng Li).
- Change default transition delay in cpufreq to 2ms (Qais Yousef).
- Drop long-unused cpudata::prev_cummulative_iowait from the
intel_pstate cpufreq driver (Jiri Slaby).
- Allow intel_pstate to assign model-specific values to strings used in
the EPP sysfs interface and make it do so on Meteor Lake (Srinivas
Pandruvada).
- Remove references to 10ms minimum sampling rate from comments in the
cpufreq code (Pierre Gondois).
- Prevent scaling_cur_freq from exceeding scaling_max_freq when the
latter is an inefficient frequency (Shivnandan Kumar).
- Honour transition_latency over transition_delay_us in cpufreq (Qais
Yousef).
- Stop unregistering cpufreq cooling on CPU hot-remove (Viresh Kumar).
- General enhancements / cleanups to ARM cpufreq drivers (tianyu2,
Nícolas F. R. A. Prado, Erick Archer, Arnd Bergmann, Anastasia
Belova).
- Update cpufreq-dt-platdev to block/approve devices (Richard Acayan).
- Make the SCMI cpufreq driver get a transition delay value from
firmware (Pierre Gondois).
* pm-cpufreq: (28 commits)
cpufreq: scmi: Set transition_delay_us
firmware: arm_scmi: Populate fast channel rate_limit
firmware: arm_scmi: Populate perf commands rate_limit
cpufreq: Don't unregister cpufreq cooling on CPU hotplug
cpufreq: Honour transition_latency over transition_delay_us
cpufreq: Limit resolving a frequency to policy min/max
cpufreq: amd-pstate: adjust min/max limit perf
cpufreq: Remove references to 10ms min sampling rate
cpufreq: intel_pstate: Update default EPPs for Meteor Lake
cpufreq: intel_pstate: Allow model specific EPPs
cpufreq: qcom-hw: add CONFIG_COMMON_CLK dependency
cpufreq: dt-platdev: block SDM670 in cpufreq-dt-platdev
cpufreq: intel_pstate: remove cpudata::prev_cummulative_iowait
cpufreq: Change default transition delay to 2ms
cpufreq: amd-pstate: Fix min_perf assignment in amd_pstate_adjust_perf()
Documentation: PM: amd-pstate: Fix section title underline
Documentation: introduce amd-pstate preferrd core mode kernel command line options
Documentation: amd-pstate: introduce amd-pstate preferred core
cpufreq: amd-pstate: Update amd-pstate preferred core ranking dynamically
ACPI: cpufreq: Add highest perf change notification
...
|
|
KVM x86 MMU changes for 6.9:
- Clean up code related to unprotecting shadow pages when retrying a guest
instruction after failed #PF-induced emulation.
- Zap TDP MMU roots at 4KiB granularity to minimize the delay in yielding if
a reschedule is needed, e.g. if a high priority task needs to run. Because
KVM doesn't support yielding in the middle of processing a zapped non-leaf
SPTE, zapping at 1GiB granularity can result in multi-millisecond lag when
attempting to schedule in a high priority.
- Rework TDP MMU root unload, free, and alloc to run with mmu_lock held for
read, e.g. to avoid serializing vCPUs when userspace deletes a memslot.
- Allocate write-tracking metadata on-demand to avoid the memory overhead when
running kernels built with KVMGT support (external write-tracking enabled),
but for workloads that don't use nested virtualization (shadow paging) or
KVMGT.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm
Merge ARM cpufreq updates for 6.9 from Viresh Kumar:
"- General enhancements / cleanups to cpufreq drivers (tianyu2, Nícolas
F. R. A. Prado, Erick Archer, Arnd Bergmann, Anastasia Belova).
- Update cpufreq-dt-platdev to block/approve devices (Richard Acayan).
- scmi: get transition delay from firmware (Pierre Gondois)."
* tag 'cpufreq-arm-updates-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
cpufreq: scmi: Set transition_delay_us
firmware: arm_scmi: Populate fast channel rate_limit
firmware: arm_scmi: Populate perf commands rate_limit
cpufreq: qcom-hw: add CONFIG_COMMON_CLK dependency
cpufreq: dt-platdev: block SDM670 in cpufreq-dt-platdev
cpufreq: mediatek-hw: Don't error out if supply is not found
Documentation: power: Use kcalloc() instead of kzalloc()
cpufreq: mediatek-hw: Wait for CPU supplies before probing
cpufreq: brcmstb-avs-cpufreq: add check for cpufreq_cpu_get's return value
cpufreq: imx6: use regmap to read ocotp register
|
|
KVM x86 misc changes for 6.9:
- Explicitly initialize a variety of on-stack variables in the emulator that
triggered KMSAN false positives (though in fairness in KMSAN, it's comically
difficult to see that the uninitialized memory is never truly consumed).
- Fix the deubgregs ABI for 32-bit KVM, and clean up code related to reading
DR6 and DR7.
- Rework the "force immediate exit" code so that vendor code ultimately
decides how and when to force the exit. This allows VMX to further optimize
handling preemption timer exits, and allows SVM to avoid sending a duplicate
IPI (SVM also has a need to force an exit).
- Fix a long-standing bug where kvm_has_noapic_vcpu could be left elevated if
vCPU creation ultimately failed, and add WARN to guard against similar bugs.
- Provide a dedicated arch hook for checking if a different vCPU was in-kernel
(for directed yield), and simplify the logic for checking if the currently
loaded vCPU is in-kernel.
- Misc cleanups and fixes.
|
|
KVM common MMU changes for 6.9:
- Harden KVM against underflowing the active mmu_notifier invalidation
count, so that "bad" invalidations (usually due to bugs elsehwere in the
kernel) are detected earlier and are less likely to hang the kernel.
- Fix a benign bug in __kvm_mmu_topup_memory_cache() where the object size
and number of objects parameters to kvmalloc_array() were swapped.
|
|
KVM async page fault changes for 6.9:
- Always flush the async page fault workqueue when a work item is being
removed, especially during vCPU destruction, to ensure that there are no
workers running in KVM code when all references to KVM-the-module are gone,
i.e. to prevent a use-after-free if kvm.ko is unloaded.
- Grab a reference to the VM's mm_struct in the async #PF worker itself instead
of gifting the worker a reference, e.g. so that there's no need to remember
to *conditionally* clean up after the worker.
|
|
Merge changes related to the runtime power management of devices for
6.9-rc1:
- Simplify pm_runtime_get_if_active() usage and add a replacement for
pm_runtime_put_autosuspend() (Sakari Ailus).
- Add a tracepoint for runtime_status changes tracking (Vilas Bhat).
- Fix section title markdown in the runtime PM documentation (Yiwei
Lin).
* pm-runtime:
Documentation: PM: Fix runtime_pm.rst markdown syntax
PM: runtime: add tracepoint for runtime_status changes
PM: runtime: Add pm_runtime_put_autosuspend() replacement
PM: runtime: Simplify pm_runtime_get_if_active() usage
|
|
KVM selftests changes for 6.9:
- Add macros to reduce the amount of boilerplate code needed to write "simple"
selftests, and to utilize selftest TAP infrastructure, which is especially
beneficial for KVM selftests with multiple testcases.
- Add basic smoke tests for SEV and SEV-ES, along with a pile of library
support for handling private/encrypted/protected memory.
- Fix benign bugs where tests neglect to close() guest_memfd files.
|
|
Merge changes related to system-wide power management for 6.9-rc1:
- Fix and clean up system suspend statistics collection (Rafael
Wysocki).
- Simplify device suspend and resume handling in the power management
core code (Rafael Wysocki).
- Add support for LZ4 compression algorithm to the hibernation image
creation and loading code (Nikhil V).
- Fix PCI hibernation support description (Yiwei Lin).
- Make hibernation take set_memory_ro() return values into account as
appropriate (Christophe Leroy).
- Set mem_sleep_current during kernel command line setup to avoid an
ordering issue with handling it (Maulik Shah).
- Fix wake IRQs handling when pm_runtime_force_suspend() is used as a
driver's system suspend callback (Qingliang Li).
* pm-sleep: (21 commits)
PM: sleep: wakeirq: fix wake irq warning in system suspend
PM: suspend: Set mem_sleep_current during kernel command line setup
PM: hibernate: Don't ignore return from set_memory_ro()
PM: hibernate: Support to select compression algorithm
Documentation: PM: Fix PCI hibernation support description
PM: hibernate: Add support for LZ4 compression for hibernation
PM: hibernate: Move to crypto APIs for LZO compression
PM: hibernate: Rename lzo* to make it generic
PM: sleep: Call dpm_async_fn() directly in each suspend phase
PM: sleep: Move devices to new lists earlier in each suspend phase
PM: sleep: Move some assignments from under a lock
PM: sleep: stats: Log errors right after running suspend callbacks
PM: sleep: stats: Use locking in dpm_save_failed_dev()
PM: sleep: stats: Call dpm_save_failed_step() at most once per phase
PM: sleep: stats: Define suspend_stats next to the code using it
PM: sleep: stats: Use unsigned int for success and failure counters
PM: sleep: stats: Use an array of step failure counters
PM: sleep: stats: Use array of suspend step names
PM: sleep: Relocate two device PM core functions
PM: sleep: Simplify dpm_suspended_list walk in dpm_resume()
...
|
|
KVM/riscv changes for 6.9
- Exception and interrupt handling for selftests
- Sstc (aka arch_timer) selftest
- Forward seed CSR access to KVM userspace
- Ztso extension support for Guest/VM
- Zacas extension support for Guest/VM
|
|
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm64 updates for 6.9
- Infrastructure for building KVM's trap configuration based on the
architectural features (or lack thereof) advertised in the VM's ID
registers
- Support for mapping vfio-pci BARs as Normal-NC (vaguely similar to
x86's WC) at stage-2, improving the performance of interacting with
assigned devices that can tolerate it
- Conversion of KVM's representation of LPIs to an xarray, utilized to
address serialization some of the serialization on the LPI injection
path
- Support for _architectural_ VHE-only systems, advertised through the
absence of FEAT_E2H0 in the CPU's ID register
- Miscellaneous cleanups, fixes, and spelling corrections to KVM and
selftests
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson into HEAD
LoongArch KVM changes for v6.9
* Set reserved bits as zero in CPUCFG.
* Start SW timer only when vcpu is blocking.
* Do not restart SW timer when it is expired.
* Remove unnecessary CSR register saving during enter guest.
|
|
Merge x86-specific ACPI changes, an ACPI backlight driver change, ACPI
APEI change and miscellaneous ACPI-related changes for 6.9-rc1:
- Add DELL0501 handling to acpi_quirk_skip_serdev_enumeration() and
make that function generic (Hans de Goede).
- Make the ACPI backlight code handle fetching EDID that is longer than
256 bytes (Mario Limonciello).
- Skip initialization of GHES_ASSIST structures for Machine Check
Architecture in APEI (Avadhut Naik).
- Convert several plaform drivers in the ACPI subsystem to using a
remove callback that returns void (Uwe Kleine-König).
- Drop the long-deprecated custom_method debugfs interface that is
problematic from the security standpoint (Rafael Wysocki).
- Use %pe in a couple of places in the ACPI code for easier error
decoding (Onkarnath).
* acpi-x86:
ACPI: x86: Add DELL0501 handling to acpi_quirk_skip_serdev_enumeration()
ACPI: x86: Move acpi_quirk_skip_serdev_enumeration() out of CONFIG_X86_ANDROID_TABLETS
* acpi-video:
ACPI: video: Handle fetching EDID that is longer than 256 bytes
* acpi-apei:
ACPI: APEI: Skip initialization of GHES_ASSIST structures for Machine Check Architecture
ACPI: APEI: GHES: Convert to platform remove callback returning void
* acpi-misc:
ACPI: pfr_update: Convert to platform remove callback returning void
ACPI: pfr_telemetry: Convert to platform remove callback returning void
ACPI: fan: Convert to platform remove callback returning void
ACPI: GED: Convert to platform remove callback returning void
ACPI: DPTF: Convert to platform remove callback returning void
ACPI: AGDI: Convert to platform remove callback returning void
ACPI: TAD: Convert to platform remove callback returning void
ACPI: Drop the custom_method debugfs interface
ACPI: use %pe for better readability of errors while printing
|
|
'acpi-thermal'
Merge ACPI tables parsing change, ACPI processor driver change, ACPI
device properties handling changes and an ACPI thermal code change for
6.9-rc1:
- Make the NFIT parsing code use acpi_evaluate_dsm_typed() (Andy
Shevchenko).
- Fix a memory leak in acpi_processor_power_exit() (Armin Wolf).
- Make it possible to quirk the CSI-2 and MIPI DisCo for Imaging
properties parsing and add a quirk for Dell XPS 9315 (Sakari Ailus).
- Prevent false-positive static checker warnings from triggering by
intializing some variables in the ACPI thermal code to zero (Colin
Ian King).
* acpi-tables:
ACPI: NFIT: Switch to use acpi_evaluate_dsm_typed()
* acpi-processor:
ACPI: processor_idle: Fix memory leak in acpi_processor_power_exit()
* acpi-property:
ACPI: property: Polish ignoring bad data nodes
ACPI: property: Ignore bad graph port nodes on Dell XPS 9315
ACPI: utils: Make acpi_handle_path() not static
* acpi-thermal:
ACPI: thermal_lib: Initialize temp_decik to zero
|
|
Merge ACPI device enumeration and bus type changes, ACPI power
management changes and ACPI IRQ override handling quirks for 6.9-rc1:
- Rearrange Device Check and Bus Check notification handling in the
ACPI device hotplug code to make it get the "enabled" _STA bit into
account (Rafael Wysocki).
- Modify acpi_processor_add() to skip processors with the "enabled"
_STA bit clear, as per the specification (Rafael Wysocki).
- Stop failing Device Check notification handling without a valid
reason (Rafael Wysocki).
- Defer enumeration of devices that depend on a device with an ACPI
device ID equalt to INTC10CF to address probe ordering issues on
some platforms (Wentong Wu).
- Constify acpi_bus_type (Ricardo Marliere).
- Make the ACPI-specific suspend-to-idle code take the Low-Power S0
Idle MSFT UUID into account on non-AMD systems (Rafael Wysocki).
- Add ACPI IRQ override quirks for some new platforms (Sergey
Kalinichev, Maxim Kudinov, Alexey Froloff, Sviatoslav Harasymchuk,
Nicolas Haye).
* acpi-scan:
ACPI: scan: Consolidate Device Check and Bus Check notification handling
ACPI: scan: Rework Device Check and Bus Check notification handling
ACPI: scan: Make acpi_processor_add() check the device enabled bit
ACPI: scan: Relocate acpi_bus_trim_one()
ACPI: scan: Fix device check notification handling
ACPI: scan: Defer enumeration of devices with a _DEP pointing to IVSC device
* acpi-bus:
ACPI: bus: make acpi_bus_type const
* acpi-pm:
ACPI: PM: s2idle: Enable Low-Power S0 Idle MSFT UUID for non-AMD systems
* acpi-resource:
ACPI: resource: Use IRQ override on Maibenben X565
ACPI: resource: Add MAIBENBEN X577 to irq1_edge_low_force_override
ACPI: resource: Do IRQ override on Lunnen Ground laptops
ACPI: resource: Add IRQ override quirk for ASUS ExpertBook B2502FBA
ACPI: resource: Skip IRQ override on ASUS ExpertBook B1502CVA
|
|
Based on the design pattern utilized in the CM GCR base address getter
implementation, the platform-specific code is capable to re-define the
getter and re-use the weakly defined initial version. But since the
pattern hasn't been used for over 10 years and another similar case (CM
L2-sync only base address getter) has just been fixed, let's unify the
interface and convert it to a more traditional single weakly defined
method: mips_cm_phys_base() (see the link below for the discussion around
this).
Link: https://lore.kernel.org/linux-mips/[email protected]
Signed-off-by: Serge Semin <[email protected]>
Signed-off-by: Thomas Bogendoerfer <[email protected]>
|
|
The __mips_cm_l2sync_phys_base() and mips_cm_l2sync_phys_base() couple was
introduced in commit 9f98f3dd0c51 ("MIPS: Add generic CM probe & access
code") where the former method was a weak implementation of the later
function. Such design pattern permitted to re-define the original method
and to use the weak implementation in the new function. A similar approach
was introduced in the framework of another arch-specific programmable
interface: mips_cm_phys_base() and __mips_cm_phys_base(). The only
difference is that the underscored method of the later couple was declared
in the "asm/mips-cm.h" header file, but it wasn't done for the CM L2-sync
methods in the subject. Due to the missing global function declaration
the "missing prototype" warning was spotted in the framework of the commit
9a2036724cd6 ("mips: mark local function static if possible") and fixed
just be re-qualifying the weak method as static. Doing that broke what was
originally implied by having the weak implementation globally defined.
Let's fix the broken CM2 L2-sync arch-interface by dropping the static
qualifier and, seeing the implemented pattern hasn't been used for over 10
years but will be required soon (see the link for the discussion around
it), converting it to a single weakly defined method:
mips_cm_l2sync_phys_base().
Fixes: 9a2036724cd6 ("mips: mark local function static if possible")
Link: https://lore.kernel.org/linux-mips/[email protected]
Signed-off-by: Serge Semin <[email protected]>
Signed-off-by: Thomas Bogendoerfer <[email protected]>
|
|
Add default #address-cells and #size-cells properties to the
usb node, which should be suitable for hubs and devices without
explicitly declared interface nodes, as:
"#address-cells":
description: should be 1 for hub nodes with device nodes,
should be 2 for device nodes with interface nodes.
enum: [1, 2]
"#size-cells":
const: 0
-- from Documentation/devicetree/bindings/usb/usb-device.yaml
Acked-by: Sergio Paracuellos <[email protected]>
Signed-off-by: Justin Swartz <[email protected]>
Reviewed-by: Arınç ÜNAL <[email protected]>
Signed-off-by: Thomas Bogendoerfer <[email protected]>
|
|
Add serial1 and serial2 nodes to define the existence of
the MT7621's second and third UARTs.
Acked-by: Sergio Paracuellos <[email protected]>
Signed-off-by: Justin Swartz <[email protected]>
Reviewed-by: Arınç ÜNAL <[email protected]>
Signed-off-by: Thomas Bogendoerfer <[email protected]>
|
|
Reorder serial0 properties according to the guidelines laid
out in Documentation/devicetree/bindings/dts-coding-style.rst
Acked-by: Sergio Paracuellos <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Signed-off-by: Justin Swartz <[email protected]>
Reviewed-by: Arınç ÜNAL <[email protected]>
Signed-off-by: Thomas Bogendoerfer <[email protected]>
|
|
Add missing pinctrl-name and pinctrl-0 properties to declare
that the uart1_pins group is associated with serial0.
Acked-by: Sergio Paracuellos <[email protected]>
Signed-off-by: Justin Swartz <[email protected]>
Reviewed-by: Arınç ÜNAL <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Signed-off-by: Thomas Bogendoerfer <[email protected]>
|
|
Update header inclusions to follow IWYU (Include What You Use)
principle.
Fixes: 5804be061848 ("MIPS: ralink: Remove unused of_gpio.h")
Reported-by: kernel test robot <[email protected]>
Closes: https://lore.kernel.org/oe-kbuild-all/[email protected]/
Signed-off-by: Andy Shevchenko <[email protected]>
Acked-by: Sergio Paracuellos <[email protected]>
Signed-off-by: Thomas Bogendoerfer <[email protected]>
|
|
The 4th Gen input preamp gain range is 0dB to +69dB, although the
control values range from 0 to 70. Replace SCARLETT2_MAX_GAIN with
SCARLETT2_MAX_GAIN_VALUE and SCARLETT2_MAX_GAIN_DB, and update the TLV
again.
Signed-off-by: Geoffrey D. Bennett <[email protected]>
Fixes: a45cf0a08347 ("ALSA: scarlett2: Fix Scarlett 4th Gen input gain range")
Message-ID: <[email protected]>
Signed-off-by: Takashi Iwai <[email protected]>
|
|
Jason Xing says:
====================
annotate data-races around sysctl_tcp_wmem[0]
Adding simple READ_ONCE() can avoid reading the sysctl knob meanwhile
someone is trying to change it.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
When reading wmem[0], it could be changed concurrently without
READ_ONCE() protection. So add one annotation here.
Signed-off-by: Jason Xing <[email protected]>
Reviewed-by: Eric Dumazet <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
It's possible that writer and the reader can manipulate the same
sysctl knob concurrently. Using READ_ONCE() to prevent reading
an old value.
Signed-off-by: Jason Xing <[email protected]>
Reviewed-by: Eric Dumazet <[email protected]>
Reviewed-by: Mat Martineau <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Running the page-pool sample on production machines under moderate
networking load shows recycling rate higher than 100%:
$ page-pool
eth0[2] page pools: 14 (zombies: 0)
refs: 89088 bytes: 364904448 (refs: 0 bytes: 0)
recycling: 100.3% (alloc: 1392:2290247724 recycle: 469289484:1828235386)
Note that outstanding refs (89088) == slow alloc * cache size (1392 * 64)
which means this machine is recycling page pool pages perfectly, not
a single page has been released.
The extra 0.3% is because sample ignores allocations from the ptr_ring.
Treat those the same as alloc_fast, the ring vs cache alloc is
already captured accurately enough by recycling stats.
With the fix:
$ page-pool
eth0[2] page pools: 14 (zombies: 0)
refs: 89088 bytes: 364904448 (refs: 0 bytes: 0)
recycling: 100.0% (alloc: 1392:2331141604 recycle: 473625579:1857460661)
Signed-off-by: Jakub Kicinski <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|