| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
module is disabled
If IPv6 is disabled on boot (ipv6.disable=1), but nft_fib_inet ends up
dealing with a IPv6 packet, it causes a kernel panic in
fib6_node_lookup_1(), crashing in bad_page_fault.
The panic is caused by trying to deference a very low address (0x38
in ppc64le), due to ipv6.fib6_main_tbl = NULL.
BUG: Kernel NULL pointer dereference at 0x00000038
The kernel panic was reproduced in a host that disabled IPv6 on boot and
have to process guest packets (coming from a bridge) using it's ip6tables.
Terminate rule evaluation when packet protocol is IPv6 but the ipv6 module
is not loaded.
Signed-off-by: Leonardo Bras <[email protected]>
Acked-by: Florian Westphal <[email protected]>
Signed-off-by: Pablo Neira Ayuso <[email protected]>
|
|
Turns out the commit 3a0681c7448b ("mmc: core: do not retry CMD6 in
__mmc_switch()") breaks initialization of a Toshiba THGBMNG5 eMMC card,
when using the meson-gx-mmc.c driver on a custom board based on Amlogic
A113D.
The CMD6 that switches the card into HS200 mode is then one that fails and
according to the below printed messages from the log:
[ 1.648951] mmc0: mmc_select_hs200 failed, error -84
[ 1.648988] mmc0: error -84 whilst initialising MMC card
After some analyze, it turns out that adding a delay of ~5ms inside
mmc_select_bus_width() but after mmc_compare_ext_csds() has been executed,
also fixes the problem. Adding yet some more debug code, trying to figure
out if potentially the card could be in a busy state, both by using CMD13
and ->card_busy() ops concluded that this was not the case.
Therefore, let's simply revert the commit that dropped support for retrying
of CMD6, as this also fixes the problem.
Fixes: 3a0681c7448b ("mmc: core: do not retry CMD6 in __mmc_switch()")
Cc: [email protected]
Signed-off-by: Jan Kaisrlik <[email protected]>
Signed-off-by: Ulf Hansson <[email protected]>
|
|
`dev` (struct rsi_91x_usbdev *) field of adapter
(struct rsi_91x_usbdev *) is allocated and initialized in
`rsi_init_usb_interface`. If any error is detected in information
read from the device side, `rsi_init_usb_interface` will be
freed. However, in the higher level error handling code in
`rsi_probe`, if error is detected, `rsi_91x_deinit` is called
again, in which `dev` will be freed again, resulting double free.
This patch fixes the double free by removing the free operation on
`dev` in `rsi_init_usb_interface`, because `rsi_91x_deinit` is also
used in `rsi_disconnect`, in that code path, the `dev` field is not
(and thus needs to be) freed.
This bug was found in v4.19, but is also present in the latest version
of kernel. Fixes CVE-2019-15504.
Reported-by: Hui Peng <[email protected]>
Reported-by: Mathias Payer <[email protected]>
Signed-off-by: Hui Peng <[email protected]>
Reviewed-by: Guenter Roeck <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
This reverts commit 9ad3b55654455258a9463384edb40077439d879f.
As reported by Sergey:
"I got some problem after upgrade kernel to 5.2 version (debian testing
linux-image-5.2.0-2-amd64). 5Ghz client stopped to see AP.
Some tests with 1metre distance between client-AP: 2.4Ghz -22dBm, for
5Ghz - 53dBm !, for longer distance (8m + walls) 2.4 - 61dBm, 5Ghz not
visible."
It was identified that rx signal level degradation was caused by
9ad3b5565445 ("rt2800: enable TX_PIN_CFG_LNA_PE_ bits per band").
So revert this commit.
Cc: <[email protected]> # v5.1+
Reported-and-tested-by: Sergey Maranchuk <[email protected]>
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
After looking at code I realized that my previous fix
95844124385e ("rt2x00: clear IV's on start to fix AP mode regression")
was incomplete. We can still have wrong IV's after re-keyring.
To fix that, clear up IV's also on key removal.
Fixes: 710e6cc1595e ("rt2800: do not nullify initialization vector data")
Signed-off-by: Stanislaw Gruszka <[email protected]>
tested-by: Emil Karlson <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
We were erroneously assigning the new configuration to a local
variable cfg, but that was not being assigned to anything, so the
change was getting lost. Assign directly to iwl_trans->cfg instead.
Fixes: 5a8c31aa6357 ("iwlwifi: pcie: fix recognition of QuZ devices")
Cc: [email protected] # 5.2
Signed-off-by: Luca Coelho <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
mwifiex_update_vs_ie(),mwifiex_set_uap_rates() and
mwifiex_set_wmm_params() call memcpy() without checking
the destination size.Since the source is given from
user-space, this may trigger a heap buffer overflow.
Fix them by putting the length check before performing memcpy().
This fix addresses CVE-2019-14814,CVE-2019-14815,CVE-2019-14816.
Signed-off-by: Wen Huang <[email protected]>
Acked-by: Ganapathi Bhat <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
MT7630E hardware does support 5GHz, but we do not properly configure phy
for 5GHz channels. Scanning at this band not only do not show any APs
but also can hang the firmware.
Since vendor reference driver do not support 5GHz we don't know how
properly configure 5GHz channels. So disable this band for MT7630E .
Cc: [email protected]
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
Since 41634aa8d6db ("mt76: only schedule txqs from the tx tasklet")
I can observe firmware hangs on MT7630E on station mode: tx stop
functioning after minor activity (rx keep working) and on module
unload device fail to stop with messages:
[ 5446.141413] mt76x0e 0000:06:00.0: TX DMA did not stop
[ 5449.176764] mt76x0e 0000:06:00.0: TX DMA did not stop
Loading module again results in failure to associate with AP.
Only machine power off / power on cycle can make device work again.
It's unclear why commit 41634aa8d6db causes the problem, but it is
related to HW encryption. Since issue is a firmware hang, that is super
hard to debug, just disable HW encryption as fix for the issue.
Fixes: 41634aa8d6db ("mt76: only schedule txqs from the tx tasklet")
Signed-off-by: Stanislaw Gruszka <[email protected]>
Signed-off-by: Kalle Valo <[email protected]>
|
|
Global pages support is removed from VT-d spec 3.0. Since global pages G
flag only affects first-level paging structures and because DMA request
with PASID are only supported by VT-d spec. 3.0 and onward, we can
safely remove global pages support.
For kernel shared virtual address IOTLB invalidation, PASID
granularity and page selective within PASID will be used. There is
no global granularity supported. Without this fix, IOTLB invalidation
will cause invalid descriptor error in the queued invalidation (QI)
interface.
Fixes: 1c4f88b7f1f9 ("iommu/vt-d: Shared virtual address in scalable mode")
Reported-by: Sanjay K Kumar <[email protected]>
Signed-off-by: Jacob Pan <[email protected]>
Signed-off-by: Joerg Roedel <[email protected]>
|
|
Single nouveau firmware fix.
Signed-off-by: Dave Airlie <[email protected]>
From: Ben Skeggs <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/CACAvsv5uGLgDY8V8pWgEH0-YhkCEgvHE=NZ1W_m0gJaoFPuQ0g@mail.gmail.com
|
|
do_sched_cfs_period_timer() will refill cfs_b runtime and call
distribute_cfs_runtime to unthrottle cfs_rq, sometimes cfs_b->runtime
will allocate all quota to one cfs_rq incorrectly, then other cfs_rqs
attached to this cfs_b can't get runtime and will be throttled.
We find that one throttled cfs_rq has non-negative
cfs_rq->runtime_remaining and cause an unexpetced cast from s64 to u64
in snippet:
distribute_cfs_runtime() {
runtime = -cfs_rq->runtime_remaining + 1;
}
The runtime here will change to a large number and consume all
cfs_b->runtime in this cfs_b period.
According to Ben Segall, the throttled cfs_rq can have
account_cfs_rq_runtime called on it because it is throttled before
idle_balance, and the idle_balance calls update_rq_clock to add time
that is accounted to the task.
This commit prevents cfs_rq to be assgined new runtime if it has been
throttled until that distribute_cfs_runtime is called.
Signed-off-by: Liangyan <[email protected]>
Signed-off-by: Peter Zijlstra (Intel) <[email protected]>
Reviewed-by: Valentin Schneider <[email protected]>
Reviewed-by: Ben Segall <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Fixes: d3d9dc330236 ("sched: Throttle entities exceeding their allowed bandwidth")
Link: https://lkml.kernel.org/r/[email protected]
Signed-off-by: Ingo Molnar <[email protected]>
|
|
Original pin node values of ASUS UX431FL with ALC294:
0x12 0xb7a60140
0x13 0x40000000
0x14 0x90170110
0x15 0x411111f0
0x16 0x411111f0
0x17 0x90170111
0x18 0x411111f0
0x19 0x411111f0
0x1a 0x411111f0
0x1b 0x411111f0
0x1d 0x4066852d
0x1e 0x411111f0
0x1f 0x411111f0
0x21 0x04211020
1. Has duplicated internal speakers (0x14 & 0x17) which makes the output
route become confused. So, the output volume cannot be changed by
setting.
2. Misses the headset mic pin node.
This patch disables the confusing speaker (NID 0x14) and enables the
headset mic (NID 0x19).
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jian-Hong Pan <[email protected]>
Cc: <[email protected]>
Signed-off-by: Takashi Iwai <[email protected]>
|
|
The socket assignment is wrong, see skb_orphan():
When skb->destructor callback is not set, but skb->sk is set, this hits BUG().
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1651813
Fixes: 554ced0a6e29 ("netfilter: nf_tables: add support for native socket matching")
Signed-off-by: Fernando Fernandez Mancera <[email protected]>
Signed-off-by: Pablo Neira Ayuso <[email protected]>
|
|
A kernel panic can happen if a host has disabled IPv6 on boot and have to
process guest packets (coming from a bridge) using it's ip6tables.
IPv6 packets need to be dropped if the IPv6 module is not loaded, and the
host ip6tables will be used.
Signed-off-by: Leonardo Bras <[email protected]>
Acked-by: Florian Westphal <[email protected]>
Signed-off-by: Pablo Neira Ayuso <[email protected]>
|
|
Refcounted, hangs of configfs_dirent, created by operations that add
fragments to configfs tree (mkdir and configfs_register_{subsystem,group}).
Will be used in the next commit to provide exclusion between fragment
removal and ->show/->store calls.
Signed-off-by: Al Viro <[email protected]>
Signed-off-by: Christoph Hellwig <[email protected]>
|
|
revert cc57c07343bd "configfs: fix registered group removal"
It was an attempt to handle something that fundamentally doesn't
work - configfs_register_group() should never be done in a part
of tree that can be rmdir'ed. And in mainline it never had been,
so let's not borrow trouble; the fix was racy anyway, it would take
a lot more to make that work and desired semantics is not clear.
Signed-off-by: Al Viro <[email protected]>
Signed-off-by: Christoph Hellwig <[email protected]>
|
|
simplifies the ->read()/->write()/->release() instances nicely
Signed-off-by: Al Viro <[email protected]>
Signed-off-by: Christoph Hellwig <[email protected]>
|
|
sun8i_dwmac_set_syscon() could be uninitialized
In function sun8i_dwmac_set_syscon(), local variable "val" could
be uninitialized if function regmap_field_read() returns -EINVAL.
However, it will be used directly in the if statement, which
is potentially unsafe.
Signed-off-by: Yizhuo <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
When the 'start' parameter is >= 0xFF000000 on 32-bit
systems, or >= 0xFFFFFFFF'FF000000 on 64-bit systems,
fill_gva_list() gets into an infinite loop.
With such inputs, 'cur' overflows after adding HV_TLB_FLUSH_UNIT
and always compares as less than end. Memory is filled with
guest virtual addresses until the system crashes.
Fix this by never incrementing 'cur' to be larger than 'end'.
Reported-by: Jong Hyun Park <[email protected]>
Signed-off-by: Tianyu Lan <[email protected]>
Reviewed-by: Michael Kelley <[email protected]>
Cc: Borislav Petkov <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Fixes: 2ffd9e33ce4a ("x86/hyper-v: Use hypercall for remote TLB flush")
Signed-off-by: Ingo Molnar <[email protected]>
|
|
We want to throw out the attrbute if it refers to the mounted on fileid,
and not the real fileid. However we do not want to block cache consistency
updates from NFSv4 writes.
Reported-by: Murphy Zhou <[email protected]>
Fixes: 7e10cc25bfa0 ("NFS: Don't refresh attributes with mounted-on-file...")
Signed-off-by: Trond Myklebust <[email protected]>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some small char and misc driver fixes for reported issues for
5.3-rc7
Also included in here is the documentation for how we are handling
hardware issues under embargo that everyone has finally agreed on, as
well as a MAINTAINERS update for the suckers who agreed to handle the
LICENSES/ files.
All of these have been in linux-next last week with no reported
issues"
* tag 'char-misc-5.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
fsi: scom: Don't abort operations for minor errors
vmw_balloon: Fix offline page marking with compaction
VMCI: Release resource if the work is already queued
Documentation/process: Embargoed hardware security issues
lkdtm/bugs: fix build error in lkdtm_EXHAUST_STACK
mei: me: add Tiger Lake point LP device ID
intel_th: pci: Add Tiger Lake support
intel_th: pci: Add support for another Lewisburg PCH
stm class: Fix a double free of stm_source_device
MAINTAINERS: add entry for LICENSES and SPDX stuff
fpga: altera-ps-spi: Fix getting of optional confd gpio
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB fixes that have been in linux-next this past
week for 5.3-rc7
They fix the usual xhci, syzbot reports, and other small issues that
have come up last week.
All have been in linux-next with no reported issues"
* tag 'usb-5.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: cdc-wdm: fix race between write and disconnect due to flag abuse
usb: host: xhci: rcar: Fix typo in compatible string matching
usb: host: xhci-tegra: Set DMA mask correctly
USB: storage: ums-realtek: Whitelist auto-delink support
USB: storage: ums-realtek: Update module parameter description for auto_delink_en
usb: host: ohci: fix a race condition between shutdown and irq
usb: hcd: use managed device resources
typec: tcpm: fix a typo in the comparison of pdo_max_voltage
usb-storage: Add new JMS567 revision to unusual_devs
usb: chipidea: udc: don't do hardware access if gadget has stopped
usbtmc: more sanity checking for packet size
usb: udc: lpc32xx: silence fall-through warning
|
|
HP Pavilion 15 (AMD Ryzen-based model) with 103c:84e7 needs the same
quirk like HP Envy/Spectre x360 for enabling the mute LED over Mic3 pin.
[ rearranged in the SSID number order by tiwai ]
Signed-off-by: Sam Bazley <[email protected]>
Cc: <[email protected]>
Signed-off-by: Takashi Iwai <[email protected]>
|
|
Identical to __put_user(); the __get_user() argument evalution will too
leak UBSAN crud into the __uaccess_begin() / __uaccess_end() region.
While uncommon this was observed to happen for:
drivers/xen/gntdev.c: if (__get_user(old_status, batch->status[i]))
where UBSAN added array bound checking.
This complements commit:
6ae865615fc4 ("x86/uaccess: Dont leak the AC flag into __put_user() argument evaluation")
Tested-by Sedat Dilek <[email protected]>
Reported-by: Randy Dunlap <[email protected]>
Signed-off-by: Peter Zijlstra (Intel) <[email protected]>
Reviewed-by: Josh Poimboeuf <[email protected]>
Reviewed-by: Thomas Gleixner <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: Randy Dunlap <[email protected]>
Cc: [email protected]
Cc: Josh Poimboeuf <[email protected]>
Link: https://lkml.kernel.org/r/[email protected]
|
|
Commit
a90118c445cc ("x86/boot: Save fields explicitly, zero out everything else")
now zeroes the secure boot setting information (enabled/disabled/...)
passed by the boot loader or by the kernel's EFI handover mechanism.
The problem manifests itself with signed kernels using the EFI handoff
protocol with grub and the kernel loses the information whether secure
boot is enabled in the firmware, i.e., the log message "Secure boot
enabled" becomes "Secure boot could not be determined".
efi_main() arch/x86/boot/compressed/eboot.c sets this field early but it
is subsequently zeroed by the above referenced commit.
Include boot_params.secure_boot in the preserve field list.
[ bp: restructure commit message and massage. ]
Fixes: a90118c445cc ("x86/boot: Save fields explicitly, zero out everything else")
Signed-off-by: John S. Gruber <[email protected]>
Signed-off-by: Borislav Petkov <[email protected]>
Reviewed-by: John Hubbard <[email protected]>
Cc: "H. Peter Anvin" <[email protected]>
Cc: Ingo Molnar <[email protected]>
Cc: Juergen Gross <[email protected]>
Cc: Mark Brown <[email protected]>
Cc: stable <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: x86-ml <[email protected]>
Link: https://lkml.kernel.org/r/CAPotdmSPExAuQcy9iAHqX3js_fc4mMLQOTr5RBGvizyCOPcTQQ@mail.gmail.com
|
|
Signed-off-by: Ben Skeggs <[email protected]>
Cc: [email protected] [v5.2+]
|
|
Pull networking fixes from David Miller:
1) Fix some length checks during OGM processing in batman-adv, from
Sven Eckelmann.
2) Fix regression that caused netfilter conntrack sysctls to not be
per-netns any more. From Florian Westphal.
3) Use after free in netpoll, from Feng Sun.
4) Guard destruction of pfifo_fast per-cpu qdisc stats with
qdisc_is_percpu_stats(), from Davide Caratti. Similar bug is fixed
in pfifo_fast_enqueue().
5) Fix memory leak in mld_del_delrec(), from Eric Dumazet.
6) Handle neigh events on internal ports correctly in nfp, from John
Hurley.
7) Clear SKB timestamp in NF flow table code so that it does not
confuse fq scheduler. From Florian Westphal.
8) taprio destroy can crash if it is invoked in a failure path of
taprio_init(), because the list head isn't setup properly yet and
the list del is unconditional. Perform the list add earlier to
address this. From Vladimir Oltean.
9) Make sure to reapply vlan filters on device up, in aquantia driver.
From Dmitry Bogdanov.
10) sgiseeq driver releases DMA memory using free_page() instead of
dma_free_attrs(). From Christophe JAILLET.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (58 commits)
net: seeq: Fix the function used to release some memory in an error handling path
enetc: Add missing call to 'pci_free_irq_vectors()' in probe and remove functions
net: bcmgenet: use ethtool_op_get_ts_info()
tc-testing: don't hardcode 'ip' in nsPlugin.py
net: dsa: microchip: add KSZ8563 compatibility string
dt-bindings: net: dsa: document additional Microchip KSZ8563 switch
net: aquantia: fix out of memory condition on rx side
net: aquantia: linkstate irq should be oneshot
net: aquantia: reapply vlan filters on up
net: aquantia: fix limit of vlan filters
net: aquantia: fix removal of vlan 0
net/sched: cbs: Set default link speed to 10 Mbps in cbs_set_port_rate
taprio: Set default link speed to 10 Mbps in taprio_set_picos_per_byte
taprio: Fix kernel panic in taprio_destroy
net: dsa: microchip: fill regmap_config name
rxrpc: Fix lack of conn cleanup when local endpoint is cleaned up [ver #2]
net: stmmac: dwmac-rk: Don't fail if phy regulator is absent
amd-xgbe: Fix error path in xgbe_mod_init()
netfilter: nft_meta_bridge: Fix get NFT_META_BRI_IIFVPROTO in network byteorder
mac80211: Correctly set noencrypt for PAE frames
...
|
|
path
In commit 99cd149efe82 ("sgiseeq: replace use of dma_cache_wback_inv"),
a call to 'get_zeroed_page()' has been turned into a call to
'dma_alloc_coherent()'. Only the remove function has been updated to turn
the corresponding 'free_page()' into 'dma_free_attrs()'.
The error hndling path of the probe function has not been updated.
Fix it now.
Rename the corresponding label to something more in line.
Fixes: 99cd149efe82 ("sgiseeq: replace use of dma_cache_wback_inv")
Signed-off-by: Christophe JAILLET <[email protected]>
Reviewed-by: Thomas Bogendoerfer <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A set of fixes for x86:
- Fix the bogus detection of 32bit user mode for uretprobes which
caused corruption of the user return address resulting in
application crashes. In the uprobes handler in_ia32_syscall() is
obviously always returning false on a 64bit kernel. Use
user_64bit_mode() instead which works correctly.
- Prevent large page splitting when ftrace flips RW/RO on the kernel
text which caused iTLB performance issues. Ftrace wants to be
converted to text_poke() which avoids the problem, but for now
allow large page preservation in the static protections check when
the change request spawns a full large page.
- Prevent arch_dynirq_lower_bound() from returning 0 when the IOAPIC
is configured via device tree. In the device tree case the GSI 1:1
mapping is meaningless therefore the lower bound which protects the
GSI range on ACPI machines is irrelevant. Return the lower bound
which the core hands to the function instead of blindly returning 0
which causes the core to allocate the invalid virtual interupt
number 0 which in turn prevents all drivers from allocating and
requesting an interrupt.
- Remove the bogus initialization of LDR and DFR in the 32bit bigsmp
APIC driver. That uses physical destination mode where LDR/DFR are
ignored, but the initialization and the missing clear of LDR caused
the APIC to be left in a inconsistent state on kexec/reboot.
- Clear LDR when clearing the APIC registers so the APIC is in a well
defined state.
- Initialize variables proper in the find_trampoline_placement()
code.
- Silence GCC( build warning for the real mode part of the build"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm/cpa: Prevent large page split when ftrace flips RW on kernel text
x86/build: Add -Wnoaddress-of-packed-member to REALMODE_CFLAGS, to silence GCC9 build warning
x86/boot/compressed/64: Fix missing initialization in find_trampoline_placement()
x86/apic: Include the LDR when clearing out APIC registers
x86/apic: Do not initialize LDR and DFR for bigsmp
uprobes/x86: Fix detection of 32-bit user mode
x86/apic: Fix arch_dynirq_lower_bound() bug for DT enabled machines
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Thomas Gleixner:
"Two fixes for perf x86 hardware implementations:
- Restrict the period on Nehalem machines to prevent perf from
hogging the CPU
- Prevent the AMD IBS driver from overwriting the hardwre controlled
and pre-seeded reserved bits (0-6) in the count register which
caused a sample bias for dispatched micro-ops"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/amd/ibs: Fix sample bias for dispatched micro-ops
perf/x86/intel: Restrict period on Nehalem
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux
Pull turbostat updates from Len Brown:
"User-space turbostat (and x86_energy_perf_policy) patches.
They are primarily bug fixes from users"
* 'turbostat' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools/power turbostat: update version number
tools/power turbostat: Add support for Hygon Fam 18h (Dhyana) RAPL
tools/power turbostat: Fix caller parameter of get_tdp_amd()
tools/power turbostat: Fix CPU%C1 display value
tools/power turbostat: do not enforce 1ms
tools/power turbostat: read from pipes too
tools/power turbostat: Add Ice Lake NNPI support
tools/power turbostat: rename has_hsw_msrs()
tools/power turbostat: Fix Haswell Core systems
tools/power turbostat: add Jacobsville support
tools/power turbostat: fix buffer overrun
tools/power turbostat: fix file descriptor leaks
tools/power turbostat: fix leak of file descriptor on error return path
tools/power turbostat: Make interval calculation per thread to reduce jitter
tools/power turbostat: remove duplicate pc10 column
tools/power x86_energy_perf_policy: Fix argument parsing
tools/power: Fix typo in man page
tools/power/x86: Enable compiler optimisations and Fortify by default
tools/power x86_energy_perf_policy: Fix "uninitialized variable" warnings at -O2
|
|
functions
Call to 'pci_free_irq_vectors()' are missing both in the error handling
path of the probe function, and in the remove function.
Add them.
Fixes: 19971f5ea0ab ("enetc: add PTP clock driver")
Signed-off-by: Christophe JAILLET <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
This change enables the use of SW timestamping on the Raspberry Pi 4.
bcmgenet's transmit function bcmgenet_xmit() implements software
timestamping. However the SOF_TIMESTAMPING_TX_SOFTWARE capability was
missing and only SOF_TIMESTAMPING_RX_SOFTWARE was announced. By using
ethtool_ops bcmgenet_ethtool_ops() as get_ts_info(), the
SOF_TIMESTAMPING_TX_SOFTWARE capability is announced.
Similar to commit a8f5cb9e7991 ("smsc95xx: use ethtool_op_get_ts_info()")
Signed-off-by: Ryan M. Collins <[email protected]>
Acked-by: Florian Fainelli <[email protected]>
Acked-by: Doug Berger <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
the following tdc test fails on Fedora:
# ./tdc.py -e 2638
-- ns/SubPlugin.__init__
Test 2638: Add matchall and try to get it
-----> prepare stage *** Could not execute: "$TC qdisc add dev $DEV1 clsact"
-----> prepare stage *** Error message: "/bin/sh: ip: command not found"
returncode 127; expected [0]
-----> prepare stage *** Aborting test run.
Let nsPlugin.py use the 'IP' variable introduced with commit 92c1a19e2fb9
("tc-tests: added path to ip command in tdc"), so that the path to 'ip' is
correctly resolved to the value we have in tdc_config.py.
# ./tdc.py -e 2638
-- ns/SubPlugin.__init__
Test 2638: Add matchall and try to get it
All test results:
1..1
ok 1 2638 - Add matchall and try to get it
Fixes: 489ce2f42514 ("tc-testing: Restore original behaviour for namespaces in tdc")
Reported-by: Hangbin Liu <[email protected]>
Signed-off-by: Davide Caratti <[email protected]>
Acked-by: Nicolas Dichtel <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Razvan Stefanescu says:
====================
net: dsa: microchip: add KSZ8563 support
This patchset adds compatibility string for the KSZ8563 switch.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
It is a 3-Port 10/100 Ethernet Switch with 1588v2 PTP.
Signed-off-by: Razvan Stefanescu <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
It is a 3-Port 10/100 Ethernet Switch with 1588v2 PTP.
Signed-off-by: Razvan Stefanescu <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Igor Russkikh says:
====================
net: aquantia: fixes on vlan filters and other conditions
Here is a set of various bug fixes related to vlan filter offload and
two other rare cases.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
On embedded environments with hard memory limits it is a normal although
rare case when skb can't be allocated on rx part under high traffic.
In such OOM cases napi_complete_done() was not called.
So the napi object became in an invalid state like it is "scheduled".
Kernel do not re-schedules the poll of that napi object.
Consequently, kernel can not remove that object the system hangs on
`ifconfig down` waiting for a poll.
We are fixing this by gracefully closing napi poll routine with correct
invocation of napi_complete_done.
This was reproduced with artificially failing the allocation of skb to
simulate an "out of memory" error case and check that traffic does
not get stuck.
Fixes: 970a2e9864b0 ("net: ethernet: aquantia: Vector operations")
Signed-off-by: Igor Russkikh <[email protected]>
Signed-off-by: Dmitry Bogdanov <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Declaring threaded irq handler should also indicate the irq is
oneshot. It is oneshot indeed, because HW implements irq automasking
on trigger.
Not declaring this causes some kernel configurations to fail
on interface up, because request_threaded_irq returned an err code.
The issue was originally hidden on normal x86_64 configuration with
latest kernel, because depending on interrupt controller, irq driver
added ONESHOT flag on its own.
Issue was observed on older kernels (4.14) where no such logic exists.
Fixes: 4c83f170b3ac ("net: aquantia: link status irq handling")
Signed-off-by: Igor Russkikh <[email protected]>
Reported-by: Michael Symolkin <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In case of device reconfiguration the driver may reset the device invisible
for other modules, vlan module in particular. So vlans will not be
removed&created and vlan filters will not be configured in the device.
The patch reapplies the vlan filters at device start.
Fixes: 7975d2aff5afb ("net: aquantia: add support of rx-vlan-filter offload")
Signed-off-by: Dmitry Bogdanov <[email protected]>
Signed-off-by: Igor Russkikh <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Fix a limit condition of vlans on the interface before setting vlan
promiscuous mode
Fixes: 48dd73d08d4dd ("net: aquantia: fix vlans not working over bridged network")
Signed-off-by: Dmitry Bogdanov <[email protected]>
Signed-off-by: Igor Russkikh <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Due to absence of checking against the rx flow rule when vlan 0 is being
removed, the other rule could be removed instead of the rule with vlan 0
Fixes: 7975d2aff5afb ("net: aquantia: add support of rx-vlan-filter offload")
Signed-off-by: Dmitry Bogdanov <[email protected]>
Signed-off-by: Igor Russkikh <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Vladimir Oltean says:
====================
Fix issues in tc-taprio and tc-cbs
This series fixes one panic and one WARN_ON found in the tc-taprio
qdisc, while trying to apply it:
- On an interface which is not multi-queue
- On an interface which has no carrier
The tc-cbs was also visually found to suffer of the same issue as
tc-taprio, and the fix was only compile-tested in that case.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
The discussion to be made is absolutely the same as in the case of
previous patch ("taprio: Set default link speed to 10 Mbps in
taprio_set_picos_per_byte"). Nothing is lost when setting a default.
Cc: Leandro Dorileo <[email protected]>
Fixes: e0a7683d30e9 ("net/sched: cbs: fix port_rate miscalculation")
Acked-by: Vinicius Costa Gomes <[email protected]>
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The taprio budget needs to be adapted at runtime according to interface
link speed. But that handling is problematic.
For one thing, installing a qdisc on an interface that doesn't have
carrier is not illegal. But taprio prints the following stack trace:
[ 31.851373] ------------[ cut here ]------------
[ 31.856024] WARNING: CPU: 1 PID: 207 at net/sched/sch_taprio.c:481 taprio_dequeue+0x1a8/0x2d4
[ 31.864566] taprio: dequeue() called with unknown picos per byte.
[ 31.864570] Modules linked in:
[ 31.873701] CPU: 1 PID: 207 Comm: tc Not tainted 5.3.0-rc5-01199-g8838fe023cd6 #1689
[ 31.881398] Hardware name: Freescale LS1021A
[ 31.885661] [<c03133a4>] (unwind_backtrace) from [<c030d8cc>] (show_stack+0x10/0x14)
[ 31.893368] [<c030d8cc>] (show_stack) from [<c10ac958>] (dump_stack+0xb4/0xc8)
[ 31.900555] [<c10ac958>] (dump_stack) from [<c0349d04>] (__warn+0xe0/0xf8)
[ 31.907395] [<c0349d04>] (__warn) from [<c0349d64>] (warn_slowpath_fmt+0x48/0x6c)
[ 31.914841] [<c0349d64>] (warn_slowpath_fmt) from [<c0f38db4>] (taprio_dequeue+0x1a8/0x2d4)
[ 31.923150] [<c0f38db4>] (taprio_dequeue) from [<c0f227b0>] (__qdisc_run+0x90/0x61c)
[ 31.930856] [<c0f227b0>] (__qdisc_run) from [<c0ec82ac>] (net_tx_action+0x12c/0x2bc)
[ 31.938560] [<c0ec82ac>] (net_tx_action) from [<c0302298>] (__do_softirq+0x130/0x3c8)
[ 31.946350] [<c0302298>] (__do_softirq) from [<c03502a0>] (irq_exit+0xbc/0xd8)
[ 31.953536] [<c03502a0>] (irq_exit) from [<c03a4808>] (__handle_domain_irq+0x60/0xb4)
[ 31.961328] [<c03a4808>] (__handle_domain_irq) from [<c0754478>] (gic_handle_irq+0x58/0x9c)
[ 31.969638] [<c0754478>] (gic_handle_irq) from [<c0301a8c>] (__irq_svc+0x6c/0x90)
[ 31.977076] Exception stack(0xe8167b20 to 0xe8167b68)
[ 31.982100] 7b20: e9d4bd80 00000cc0 000000cf 00000000 e9d4bd80 c1f38958 00000cc0 c1f38960
[ 31.990234] 7b40: 00000001 000000cf 00000004 e9dc0800 00000000 e8167b70 c0f478ec c0f46d94
[ 31.998363] 7b60: 60070013 ffffffff
[ 32.001833] [<c0301a8c>] (__irq_svc) from [<c0f46d94>] (netlink_trim+0x18/0xd8)
[ 32.009104] [<c0f46d94>] (netlink_trim) from [<c0f478ec>] (netlink_broadcast_filtered+0x34/0x414)
[ 32.017930] [<c0f478ec>] (netlink_broadcast_filtered) from [<c0f47cec>] (netlink_broadcast+0x20/0x28)
[ 32.027102] [<c0f47cec>] (netlink_broadcast) from [<c0eea378>] (rtnetlink_send+0x34/0x88)
[ 32.035238] [<c0eea378>] (rtnetlink_send) from [<c0f25890>] (notify_and_destroy+0x2c/0x44)
[ 32.043461] [<c0f25890>] (notify_and_destroy) from [<c0f25e08>] (qdisc_graft+0x398/0x470)
[ 32.051595] [<c0f25e08>] (qdisc_graft) from [<c0f27a00>] (tc_modify_qdisc+0x3a4/0x724)
[ 32.059470] [<c0f27a00>] (tc_modify_qdisc) from [<c0ee4c84>] (rtnetlink_rcv_msg+0x260/0x2ec)
[ 32.067864] [<c0ee4c84>] (rtnetlink_rcv_msg) from [<c0f4a988>] (netlink_rcv_skb+0xb8/0x110)
[ 32.076172] [<c0f4a988>] (netlink_rcv_skb) from [<c0f4a170>] (netlink_unicast+0x1b4/0x22c)
[ 32.084392] [<c0f4a170>] (netlink_unicast) from [<c0f4a5e4>] (netlink_sendmsg+0x33c/0x380)
[ 32.092614] [<c0f4a5e4>] (netlink_sendmsg) from [<c0ea9f40>] (sock_sendmsg+0x14/0x24)
[ 32.100403] [<c0ea9f40>] (sock_sendmsg) from [<c0eaa780>] (___sys_sendmsg+0x214/0x228)
[ 32.108279] [<c0eaa780>] (___sys_sendmsg) from [<c0eabad0>] (__sys_sendmsg+0x50/0x8c)
[ 32.116068] [<c0eabad0>] (__sys_sendmsg) from [<c0301000>] (ret_fast_syscall+0x0/0x54)
[ 32.123938] Exception stack(0xe8167fa8 to 0xe8167ff0)
[ 32.128960] 7fa0: b6fa68c8 000000f8 00000003 bea142d0 00000000 00000000
[ 32.137093] 7fc0: b6fa68c8 000000f8 0052154c 00000128 5d6468a2 00000000 00000028 00558c9c
[ 32.145224] 7fe0: 00000070 bea14278 00530d64 b6e17e64
[ 32.150659] ---[ end trace 2139c9827c3e5177 ]---
This happens because the qdisc ->dequeue callback gets called. Which
again is not illegal, the qdisc will dequeue even when the interface is
up but doesn't have carrier (and hence SPEED_UNKNOWN), and the frames
will be dropped further down the stack in dev_direct_xmit().
And, at the end of the day, for what? For calculating the initial budget
of an interface which is non-operational at the moment and where frames
will get dropped anyway.
So if we can't figure out the link speed, default to SPEED_10 and move
along. We can also remove the runtime check now.
Cc: Leandro Dorileo <[email protected]>
Fixes: 7b9eba7ba0c1 ("net/sched: taprio: fix picos_per_byte miscalculation")
Acked-by: Vinicius Costa Gomes <[email protected]>
Signed-off-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
taprio_init may fail earlier than this line:
list_add(&q->taprio_list, &taprio_list);
i.e. due to the net device not being multi queue.
Attempting to remove q from the global taprio_list when it is not part
of it will result in a kernel panic.
Fix it by matching list_add and list_del better to one another in the
order of operations. This way we can keep the deletion unconditional
and with lower complexity - O(1).
Cc: Leandro Dorileo <[email protected]>
Fixes: 7b9eba7ba0c1 ("net/sched: taprio: fix picos_per_byte miscalculation")
Signed-off-by: Vladimir Oltean <[email protected]>
Acked-by: Vinicius Costa Gomes <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Use the register value width as the regmap_config name to prevent the
following error when the second and third regmap_configs are
initialized.
"debugfs: Directory '${bus-id}' with parent 'regmap' already present!"
Signed-off-by: George McCollister <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|