| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Increase critical threshold for ASIC thermal zone from 110C to 140C
according to the system hardware requirements. All the supported ASICs
(Spectrum-1, Spectrum-2, Spectrum-3) could be still operational with ASIC
temperature below 140C. With the old critical threshold value system
can perform unjustified shutdown.
All the systems equipped with the above ASICs implement thermal
protection mechanism at firmware level and firmware could decide to
perform system thermal shutdown in case the temperature is below 140C.
So with the new threshold system will not meltdown, while thermal
operating range will be aligned with hardware abilities.
Fixes: 41e760841d26 ("mlxsw: core: Replace thermal temperature trips with defines")
Fixes: a50c1e35650b ("mlxsw: core: Implement thermal zone")
Signed-off-by: Vadim Pasternak <[email protected]>
Reviewed-by: Jiri Pirko <[email protected]>
Signed-off-by: Ido Schimmel <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Validate thresholds to avoid a single failure due to some transceiver
unreliability. Ignore the last readouts in case warning temperature is
above alarm temperature, since it can cause unexpected thermal
shutdown. Stay with the previous values and refresh threshold within
the next iteration.
This is a rare scenario, but it was observed at a customer site.
Fixes: 6a79507cfe94 ("mlxsw: core: Extend thermal module with per QSFP module thermal zones")
Signed-off-by: Vadim Pasternak <[email protected]>
Reviewed-by: Jiri Pirko <[email protected]>
Signed-off-by: Ido Schimmel <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
The buffer list can have zero skb as following path:
tipc_named_node_up()->tipc_node_xmit()->tipc_link_xmit(), so
we need to check the list before casting an &sk_buff.
Fault report:
[] tipc: Bulk publication failure
[] general protection fault, probably for non-canonical [#1] PREEMPT [...]
[] KASAN: null-ptr-deref in range [0x00000000000000c8-0x00000000000000cf]
[] CPU: 0 PID: 0 Comm: swapper/0 Kdump: loaded Not tainted 5.10.0-rc4+ #2
[] Hardware name: Bochs ..., BIOS Bochs 01/01/2011
[] RIP: 0010:tipc_link_xmit+0xc1/0x2180
[] Code: 24 b8 00 00 00 00 4d 39 ec 4c 0f 44 e8 e8 d7 0a 10 f9 48 [...]
[] RSP: 0018:ffffc90000006ea0 EFLAGS: 00010202
[] RAX: dffffc0000000000 RBX: ffff8880224da000 RCX: 1ffff11003d3cc0d
[] RDX: 0000000000000019 RSI: ffffffff886007b9 RDI: 00000000000000c8
[] RBP: ffffc90000007018 R08: 0000000000000001 R09: fffff52000000ded
[] R10: 0000000000000003 R11: fffff52000000dec R12: ffffc90000007148
[] R13: 0000000000000000 R14: 0000000000000000 R15: ffffc90000007018
[] FS: 0000000000000000(0000) GS:ffff888037400000(0000) knlGS:000[...]
[] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[] CR2: 00007fffd2db5000 CR3: 000000002b08f000 CR4: 00000000000006f0
Fixes: af9b028e270fd ("tipc: make media xmit call outside node spinlock context")
Acked-by: Jon Maloy <[email protected]>
Signed-off-by: Hoang Le <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
TLS selftests where broken because of wrong variable types used.
Fix it by changing u16 -> uint16_t
Fixes: 4f336e88a870 ("selftests/tls: add CHACHA20-POLY1305 to tls selftests")
Reported-by: kernel test robot <[email protected]>
Signed-off-by: Vadim Fedorenko <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
commit b91540d52a08 ("RISC-V: Add EFI runtime services") add
a duplicated PAGE_KERNEL_EXEC, kill it.
Signed-off-by: Kefeng Wang <[email protected]>
Reviewed-by: Pekka Enberg <[email protected]>
Reviewed-by: Atish Patra <[email protected]>
Fixes: b91540d52a08 ("RISC-V: Add EFI runtime services")
Cc: [email protected]
Signed-off-by: Palmer Dabbelt <[email protected]>
|
|
There are cases where GSO segment's length exceeds the egress MTU:
- Forwarding of a TCP GRO skb, when DF flag is not set.
- Forwarding of an skb that arrived on a virtualisation interface
(virtio-net/vhost/tap) with TSO/GSO size set by other network
stack.
- Local GSO skb transmitted on an NETIF_F_TSO tunnel stacked over an
interface with a smaller MTU.
- Arriving GRO skb (or GSO skb in a virtualised environment) that is
bridged to a NETIF_F_TSO tunnel stacked over an interface with an
insufficient MTU.
If so:
- Consume the SKB and its segments.
- Issue an ICMP packet with 'Packet Too Big' message containing the
MTU, allowing the source host to reduce its Path MTU appropriately.
Note: These cases are handled in the same manner in IPv4 output finish.
This patch aligns the behavior of IPv6 and the one of IPv4.
Fixes: 9e50849054a4 ("netfilter: ipv6: move POSTROUTING invocation before fragmentation")
Signed-off-by: Aya Levin <[email protected]>
Reviewed-by: Tariq Toukan <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
For all PCI functions on the netxen_nic adapter, interrupt
mode (INTx or MSI) configuration is dependent on what has
been configured by the PCI function zero in the shared
interrupt register, as these adapters do not support mixed
mode interrupts among the functions of a given adapter.
Logic for setting MSI/MSI-x interrupt mode in the shared interrupt
register based on PCI function id zero check is not appropriate for
all family of netxen adapters, as for some of the netxen family
adapters PCI function zero is not really meant to be probed/loaded
in the host but rather just act as a management function on the device,
which caused all the other PCI functions on the adapter to always use
legacy interrupt (INTx) mode instead of choosing MSI/MSI-x interrupt mode.
This patch replaces that check with port number so that for all
type of adapters driver attempts for MSI/MSI-x interrupt modes.
Fixes: b37eb210c076 ("netxen_nic: Avoid mixed mode interrupts")
Signed-off-by: Manish Chopra <[email protected]>
Signed-off-by: Igor Russkikh <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
- Fix possible KASAN issue in amd_energy driver
- Avoid configuration problem in pwm-fan driver
- Fix kernel-doc warning in sbtsi_temp documentation
* tag 'hwmon-for-v5.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (amd_energy) fix allocation of hwmon_channel_info config
hwmon: (pwm-fan) Ensure that calculation doesn't discard big period values
hwmon: (sbtsi_temp) Fix Documenation kernel-doc warning
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine
Pull dmaengine fixes from Vinod Koul:
"A bunch of dmaengine driver fixes for:
- coverity discovered issues for xilinx driver
- qcom, gpi driver fix for undefined bhaviour and one off cleanup
- update Peter's email for TI DMA drivers
- one-off for idxd driver
- resource leak fix for mediatek and milbeaut drivers"
* tag 'dmaengine-fix-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine:
dmaengine: stm32-mdma: fix STM32_MDMA_VERY_HIGH_PRIORITY value
dmaengine: xilinx_dma: fix mixed_enum_type coverity warning
dmaengine: xilinx_dma: fix incompatible param warning in _child_probe()
dmaengine: xilinx_dma: check dma_async_device_register return value
dmaengine: qcom: fix gpi undefined behavior
dt-bindings: dma: ti: Update maintainer and author information
MAINTAINERS: Add entry for Texas Instruments DMA drivers
qcom: bam_dma: Delete useless kfree code
dmaengine: dw-edma: Fix use after free in dw_edma_alloc_chunk()
dmaengine: milbeaut-xdmac: Fix a resource leak in the error handling path of the probe function
dmaengine: mediatek: mtk-hsdma: Fix a resource leak in the error handling path of the probe function
dmaengine: qcom: gpi: Fixes a format mismatch
dmaengine: idxd: off by one in cleanup code
dmaengine: ti: k3-udma: Fix pktdma rchan TPL level setup
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Three driver bugfixes for I2C. Buisness as usual"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: mediatek: Fix apdma and i2c hand-shake timeout
i2c: i801: Fix the i2c-mux gpiod_lookup_table not being properly terminated
i2c: sprd: use a specific timeout to avoid system hang up issue
|
|
Change my email contact ahead of a likely painful eleven-month migration
to a certain cobalt enteprisey groupware cloud product that will totally
break my workflow. Some day I may get used to having to email being
sequestered behind both claret and cerulean oath2+sms 2fa layers, but
for now I'll stick with keying in one password to receive an email vs.
the required four.
Signed-off-by: Darrick J. Wong <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
When the creator of SQPOLL io_uring dies (i.e. sqo_task), we don't want
its internals like ->files and ->mm to be poked by the SQPOLL task, it
have never been nice and recently got racy. That can happen when the
owner undergoes destruction and SQPOLL tasks tries to submit new
requests in parallel, and so calls io_sq_thread_acquire*().
That patch halts SQPOLL submissions when sqo_task dies by introducing
sqo_dead flag. Once set, the SQPOLL task must not do any submission,
which is synchronised by uring_lock as well as the new flag.
The tricky part is to make sure that disabling always happens, that
means either the ring is discovered by creator's do_exit() -> cancel,
or if the final close() happens before it's done by the creator. The
last is guaranteed by the fact that for SQPOLL the creator task and only
it holds exactly one file note, so either it pins up to do_exit() or
removed by the creator on the final put in flush. (see comments in
uring_flush() around file->f_count == 2).
One more place that can trigger io_sq_thread_acquire_*() is
__io_req_task_submit(). Shoot off requests on sqo_dead there, even
though actually we don't need to. That's because cancellation of
sqo_task should wait for the request before going any further.
note 1: io_disable_sqo_submit() does io_ring_set_wakeup_flag() so the
caller would enter the ring to get an error, but it still doesn't
guarantee that the flag won't be cleared.
note 2: if final __userspace__ close happens not from the creator
task, the file note will pin the ring until the task dies.
Fixed: b1b6b5a30dce8 ("kernel/io_uring: cancel io_uring before task works")
Signed-off-by: Pavel Begunkov <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
files_cancel() should cancel all relevant requests and drop file notes,
so we should never have file notes after that, including on-exit fput
and flush. Add a WARN_ONCE to be sure.
Signed-off-by: Pavel Begunkov <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
A simple preparation change inlining io_uring_attempt_task_drop() into
io_uring_flush().
Signed-off-by: Pavel Begunkov <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
We expect io_rw_reissue() to take place only during submission with
uring_lock held. Add a lockdep annotation to check that invariant.
Signed-off-by: Pavel Begunkov <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
BCH_FEATURE_INCOMPAT_OBSO_LARGE_BUCKET
If BCH_FEATURE_INCOMPAT_OBSO_LARGE_BUCKET is set in incompat feature
set, it means the cache device is created with obsoleted layout with
obso_bucket_site_hi. Now bcache does not support this feature bit, a new
BCH_FEATURE_INCOMPAT_LOG_LARGE_BUCKET_SIZE incompat feature bit is added
for a better layout to support large bucket size.
For the legacy compatibility purpose, if a cache device created with
obsoleted BCH_FEATURE_INCOMPAT_OBSO_LARGE_BUCKET feature bit, all bcache
devices attached to this cache set should be set to read-only. Then the
dirty data can be written back to backing device before re-create the
cache device with BCH_FEATURE_INCOMPAT_LOG_LARGE_BUCKET_SIZE feature bit
by the latest bcache-tools.
This patch checks BCH_FEATURE_INCOMPAT_OBSO_LARGE_BUCKET feature bit
when running a cache set and attach a bcache device to the cache set. If
this bit is set,
- When run a cache set, print an error kernel message to indicate all
following attached bcache device will be read-only.
- When attach a bcache device, print an error kernel message to indicate
the attached bcache device will be read-only, and ask users to update
to latest bcache-tools.
Such change is only for cache device whose bucket size >= 32MB, this is
for the zoned SSD and almost nobody uses such large bucket size at this
moment. If you don't explicit set a large bucket size for a zoned SSD,
such change is totally transparent to your bcache device.
Fixes: ffa470327572 ("bcache: add bucket_size_hi into struct cache_sb_disk for large bucket")
Signed-off-by: Coly Li <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
When large bucket feature was added, BCH_FEATURE_INCOMPAT_LARGE_BUCKET
was introduced into the incompat feature set. It used bucket_size_hi
(which was added at the tail of struct cache_sb_disk) to extend current
16bit bucket size to 32bit with existing bucket_size in struct
cache_sb_disk.
This is not a good idea, there are two obvious problems,
- Bucket size is always value power of 2, if store log2(bucket size) in
existing bucket_size of struct cache_sb_disk, it is unnecessary to add
bucket_size_hi.
- Macro csum_set() assumes d[SB_JOURNAL_BUCKETS] is the last member in
struct cache_sb_disk, bucket_size_hi was added after d[] which makes
csum_set calculate an unexpected super block checksum.
To fix the above problems, this patch introduces a new incompat feature
bit BCH_FEATURE_INCOMPAT_LOG_LARGE_BUCKET_SIZE, when this bit is set, it
means bucket_size in struct cache_sb_disk stores the order of power-of-2
bucket size value. When user specifies a bucket size larger than 32768
sectors, BCH_FEATURE_INCOMPAT_LOG_LARGE_BUCKET_SIZE will be set to
incompat feature set, and bucket_size stores log2(bucket size) more
than store the real bucket size value.
The obsoleted BCH_FEATURE_INCOMPAT_LARGE_BUCKET won't be used anymore,
it is renamed to BCH_FEATURE_INCOMPAT_OBSO_LARGE_BUCKET and still only
recognized by kernel driver for legacy compatible purpose. The previous
bucket_size_hi is renmaed to obso_bucket_size_hi in struct cache_sb_disk
and not used in bcache-tools anymore.
For cache device created with BCH_FEATURE_INCOMPAT_LARGE_BUCKET feature,
bcache-tools and kernel driver still recognize the feature string and
display it as "obso_large_bucket".
With this change, the unnecessary extra space extend of bcache on-disk
super block can be avoided, and csum_set() may generate expected check
sum as well.
Fixes: ffa470327572 ("bcache: add bucket_size_hi into struct cache_sb_disk for large bucket")
Signed-off-by: Coly Li <[email protected]>
Cc: [email protected] # 5.9+
Signed-off-by: Jens Axboe <[email protected]>
|
|
This patch adds the check for features which is incompatible for
current supported feature sets.
Now if the bcache device created by bcache-tools has features that
current kernel doesn't support, read_super() will fail with error
messoage. E.g. if an unsupported incompatible feature detected,
bcache register will fail with dmesg "bcache: register_bcache() error :
Unsupported incompatible feature found".
Fixes: d721a43ff69c ("bcache: increase super block version for cache device and backing device")
Fixes: ffa470327572 ("bcache: add bucket_size_hi into struct cache_sb_disk for large bucket")
Signed-off-by: Coly Li <[email protected]>
Cc: [email protected] # 5.9+
Signed-off-by: Jens Axboe <[email protected]>
|
|
This patch fixes the following typos,
from BCH_FEATURE_COMPAT_SUUP to BCH_FEATURE_COMPAT_SUPP
from BCH_FEATURE_INCOMPAT_SUUP to BCH_FEATURE_INCOMPAT_SUPP
from BCH_FEATURE_INCOMPAT_SUUP to BCH_FEATURE_RO_COMPAT_SUPP
Fixes: d721a43ff69c ("bcache: increase super block version for cache device and backing device")
Fixes: ffa470327572 ("bcache: add bucket_size_hi into struct cache_sb_disk for large bucket")
Signed-off-by: Coly Li <[email protected]>
Cc: [email protected] # 5.9+
Signed-off-by: Jens Axboe <[email protected]>
|
|
There is no need to reassign pdev_set_uuid in the second loop iteration,
so move it to the place before second loop.
Signed-off-by: Yi Li <[email protected]>
Signed-off-by: Coly Li <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
Jakub Kicinski says:
====================
net: fix issues around register_netdevice() failures
This series attempts to clean up the life cycle of struct
net_device. Dave has added dev->needs_free_netdev in the
past to fix double frees, we can lean on that mechanism
a little more to fix remaining issues with register_netdevice().
This is the next chapter of the saga which already includes:
commit 0e0eee2465df ("net: correct error path in rtnl_newlink()")
commit e51fb152318e ("rtnetlink: fix a memory leak when ->newlink fails")
commit cf124db566e6 ("net: Fix inconsistent teardown and release of private netdev state.")
commit 93ee31f14f6f ("[NET]: Fix free_netdev on register_netdev failure.")
commit 814152a89ed5 ("net: fix memleak in register_netdevice()")
commit 10cc514f451a ("net: Fix null de-reference of device refcount")
The immediate problem which gets fixed here is that calling
free_netdev() right after unregister_netdevice() is illegal
because we need to release rtnl_lock first, to let the
unregistration finish. Note that unregister_netdevice() is
just a wrapper of unregister_netdevice_queue(), it only
does half of the job.
Where this limitation becomes most problematic is in failure
modes of register_netdevice(). There is a notifier call right
at the end of it, which lets other subsystems veto the entire
thing. At which point we should really go through a full
unregister_netdevice(), but we can't because callers may
go straight to free_netdev() after the failure, and that's
no bueno (see the previous paragraph).
This set makes free_netdev() more lenient, when device
is still being unregistered free_netdev() will simply set
dev->needs_free_netdev and let the unregister process do
the freeing.
With the free_netdev() problem out of the way failures in
register_netdevice() can make use of net_todo, again.
Users are still expected to call free_netdev() right after
failure but that will only set dev->needs_free_netdev.
To prevent the pathological case of:
dev->needs_free_netdev = true;
if (register_netdevice(dev)) {
rtnl_unlock();
free_netdev(dev);
}
make register_netdevice()'s failure clear dev->needs_free_netdev.
Problems described above are only present with register_netdevice() /
unregister_netdevice(). We have two parallel APIs for registration
of devices:
- those called outside rtnl_lock (register_netdev(), and
unregister_netdev());
- and those to be used under rtnl_lock - register_netdevice()
and unregister_netdevice().
The former is trivial and has no problems. The alternative
approach to fix the latter would be to also separate the
freeing functions - i.e. add free_netdevice(). This has been
implemented (incl. converting all relevant calls in the tree)
but it feels a little unnecessary to put the burden of choosing
the right free_netdev{,ice}() call on the programmer when we
can "just do the right thing" by default.
====================
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
If register_netdevice() fails at the very last stage - the
notifier call - some subsystems may have already seen it and
grabbed a reference. struct net_device can't be freed right
away without calling netdev_wait_all_refs().
Now that we have a clean interface in form of dev->needs_free_netdev
and lenient free_netdev() we can undo what commit 93ee31f14f6f ("[NET]:
Fix free_netdev on register_netdev failure.") has done and complete
the unregistration path by bringing the net_set_todo() call back.
After registration fails user is still expected to explicitly
free the net_device, so make sure ->needs_free_netdev is cleared,
otherwise rolling back the registration will cause the old double
free for callers who release rtnl_lock before the free.
This also solves the problem of priv_destructor not being called
on notifier error.
net_set_todo() will be moved back into unregister_netdevice_queue()
in a follow up.
Reported-by: Hulk Robot <[email protected]>
Reported-by: Yang Yingliang <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
There are two flavors of handling netdev registration:
- ones called without holding rtnl_lock: register_netdev() and
unregister_netdev(); and
- those called with rtnl_lock held: register_netdevice() and
unregister_netdevice().
While the semantics of the former are pretty clear, the same can't
be said about the latter. The netdev_todo mechanism is utilized to
perform some of the device unregistering tasks and it hooks into
rtnl_unlock() so the locked variants can't actually finish the work.
In general free_netdev() does not mix well with locked calls. Most
drivers operating under rtnl_lock set dev->needs_free_netdev to true
and expect core to make the free_netdev() call some time later.
The part where this becomes most problematic is error paths. There is
no way to unwind the state cleanly after a call to register_netdevice(),
since unreg can't be performed fully without dropping locks.
Make free_netdev() more lenient, and defer the freeing if device
is being unregistered. This allows error paths to simply call
free_netdev() both after register_netdevice() failed, and after
a call to unregister_netdevice() but before dropping rtnl_lock.
Simplify the error paths which are currently doing gymnastics
around free_netdev() handling.
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Explain the two basic flows of struct net_device's operation.
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
When setting up a channel bridge, ppp_bridge_channels sets the
pch->bridge field before taking the associated reference on the bridge
file instance.
This opens up a refcount underflow bug if ppp_bridge_channels called
via. iotcl runs concurrently with ppp_unbridge_channels executing via.
file release.
The bug is triggered by ppp_bridge_channels taking the error path
through the 'err_unset' label. In this scenario, pch->bridge is set,
but the reference on the bridged channel will not be taken because
the function errors out. If ppp_unbridge_channels observes pch->bridge
before it is unset by the error path, it will erroneously drop the
reference on the bridged channel and cause a refcount underflow.
To avoid this, ensure that ppp_bridge_channels holds a reference on
each channel in advance of setting the bridge pointers.
Signed-off-by: Tom Parkin <[email protected]>
Fixes: 4cf476ced45d ("ppp: add PPPIOCBRIDGECHAN and PPPIOCUNBRIDGECHAN ioctls")
Acked-by: Guillaume Nault <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
reuse->socks[] is modified concurrently by reuseport_add_sock. To
prevent reading values that have not been fully initialized, only read
the array up until the last known safe index instead of incorrectly
re-reading the last index of the array.
Fixes: acdcecc61285f ("udp: correct reuseport selection with connected sockets")
Signed-off-by: Baptiste Lepers <[email protected]>
Acked-by: Willem de Bruijn <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
skbs in fraglist could be shared by a BPF filter loaded at TC. If TC
writes, it will call skb_ensure_writable -> pskb_expand_head to create
a private linear section for the head_skb. And then call
skb_clone_fraglist -> skb_get on each skb in the fraglist.
skb_segment_list overwrites part of the skb linear section of each
fragment itself. Even after skb_clone, the frag_skbs share their
linear section with their clone in PF_PACKET.
Both sk_receive_queue of PF_PACKET and PF_INET (or PF_INET6) can have
a link for the same frag_skbs chain. If a new skb (not frags) is
queued to one of the sk_receive_queue, multiple ptypes can see and
release this. It causes use-after-free.
[ 4443.426215] ------------[ cut here ]------------
[ 4443.426222] refcount_t: underflow; use-after-free.
[ 4443.426291] WARNING: CPU: 7 PID: 28161 at lib/refcount.c:190
refcount_dec_and_test_checked+0xa4/0xc8
[ 4443.426726] pstate: 60400005 (nZCv daif +PAN -UAO)
[ 4443.426732] pc : refcount_dec_and_test_checked+0xa4/0xc8
[ 4443.426737] lr : refcount_dec_and_test_checked+0xa0/0xc8
[ 4443.426808] Call trace:
[ 4443.426813] refcount_dec_and_test_checked+0xa4/0xc8
[ 4443.426823] skb_release_data+0x144/0x264
[ 4443.426828] kfree_skb+0x58/0xc4
[ 4443.426832] skb_queue_purge+0x64/0x9c
[ 4443.426844] packet_set_ring+0x5f0/0x820
[ 4443.426849] packet_setsockopt+0x5a4/0xcd0
[ 4443.426853] __sys_setsockopt+0x188/0x278
[ 4443.426858] __arm64_sys_setsockopt+0x28/0x38
[ 4443.426869] el0_svc_common+0xf0/0x1d0
[ 4443.426873] el0_svc_handler+0x74/0x98
[ 4443.426880] el0_svc+0x8/0xc
Fixes: 3a1296a38d0c (net: Support GRO/GSO fraglist chaining.)
Signed-off-by: Dongseok Yi <[email protected]>
Acked-by: Willem de Bruijn <[email protected]>
Acked-by: Daniel Borkmann <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
At the moment it is quite hard to identify the network interface
provided by IPA in userspace components: The network interface is
created as virtual device, without any link to the IPA device.
The interface name ("rmnet_ipa%d") is the only indication that the
network interface belongs to IPA, but this is not very reliable.
Add SET_NETDEV_DEV() to associate the network interface with the
IPA parent device. This allows userspace services like ModemManager
to properly identify that this network interface is provided by IPA
and belongs to the modem.
Cc: Alex Elder <[email protected]>
Fixes: a646d6ec9098 ("soc: qcom: ipa: modem and microcontroller")
Signed-off-by: Stephan Gerhold <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/zonefs
Pull zonefs fix from Damien Le Moal:
"A single patch from Arnd to fix a missing dependency in zonefs
Kconfig"
* tag 'zonefs-5.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/zonefs:
zonefs: select CONFIG_CRC32
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kunit fixes from Shuah Khan:
"One fix to force the use of the 'tty' console for UML.
Given that kunit tool requires the console output, explicitly stating
the dependency makes sense than relying on it being the default"
* tag 'linux-kselftest-kunit-fixes-5.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
kunit: tool: Force the use of the 'tty' console for UML
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kselftest fixes from Shuah Khan:
"Two minor fixes to vDSO test changes in this merge window"
* tag 'linux-kselftest-next-5.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests/vDSO: fix -Wformat warning in vdso_test_correctness
selftests/vDSO: add additional binaries to .gitignore
|
|
Pull documentation fixes from Jonathan Corbet:
"A handful of relatively small documentation fixes"
* tag 'docs-5.11-3' of git://git.lwn.net/linux:
docs: admin-guide: bootconfig: Fix feils to fails
Documentation/admin-guide: kernel-parameters: hyphenate comma-separated
docs: binfmt-misc: Fix .rst formatting
docs: remove mention of ENABLE_MUST_CHECK
atomic: remove further references to atomic_ops
Documentation: doc-guide: fixes to sphinx.rst
docs/mm: concepts.rst: Correct the threshold to low watermark
Documentation: admin: early_param()s are also listed in kernel-parameters
docs: Fix reST markup when linking to sections
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull device properties framework fixes from Rafael Wysocki:
"Revert a problematic commit that went in during the 5.10 cycle and
improve the kerneldoc description of the function affected by it (both
changes from Bard Liao)"
* tag 'devprop-5.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
device property: add description of fwnode cases
Revert "device property: Keep secondary firmware node secondary by type"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These address two build issues and drop confusing text from a couple
of Kconfig entries.
Specifics:
- Drop two local variables that are never read and the code updating
their values from the x86 suspend-to-idle code (Rafael Wysocki)
- Add empty stub of an ACPI helper function to avoid build issues
when CONFIG_ACPI is not set (Shawn Guo)
- Remove confusing text regarding modules from Kconfig entries that
correspond to non-modular code (Peter Robinson)"
* tag 'acpi-5.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: Update Kconfig help text for items that are no longer modular
ACPI: scan: add stub acpi_create_platform_device() for !CONFIG_ACPI
ACPI: PM: s2idle: Drop unused local variables and related code
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These address two issues in the intel_pstate driver and one in the
powernow-k8 cpufreq driver.
Specifics:
- Make the powernow-k8 cpufreq driver avoid calling
cpufreq_cpu_get(), which theoretically may return NULL, to get a
policy pointer that is known to it already (Colin Ian King)
- Drop two functions that are not used any more from the intel_pstate
driver (Lukas Bulwahn)
- Make intel_pstate check the HWP capabilities to get the maximum
available P-state in the passive mode to avoid using a stale value
of it in case of out-of-band updates (Rafael Wysocki)"
* tag 'pm-5.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: intel_pstate: remove obsolete functions
cpufreq: powernow-k8: pass policy rather than use cpufreq_cpu_get()
cpufreq: intel_pstate: Use HWP capabilities in intel_cpufreq_adjust_perf()
|
|
Pull drm fixes from Daniel Vetter:
"Looks like people are back from the break, usual small pile of fixes
all over. Next week Dave should be back.
The only thing pending I'm aware of is a "this shouldn't have become
uapi" reverts for amdgpu, but they're already on the list and not that
important really so can wait another week.
Summary:
- fix for ttm list corruption in radeon, reported by a few people
- fixes for amdgpu, i915, msm
- dma-buf use-after free fix"
* tag 'drm-fixes-2021-01-08' of git://anongit.freedesktop.org/drm/drm: (29 commits)
drm/msm: Only enable A6xx LLCC code on A6xx
drm/msm: Add modparam to allow vram carveout
drm/msm: Call msm_init_vram before binding the gpu
drm/msm/dp: postpone irq_hpd event during connection pending state
drm/ttm: unexport ttm_pool_init/fini
drm/radeon: stop re-init the TTM page pool
dmabuf: fix use-after-free of dmabuf's file->f_inode
Revert "drm/amd/display: Fix memory leaks in S3 resume"
drm/amdgpu/display: drop DCN support for aarch64
drm/amdgpu: enable ras eeprom support for sienna cichlid
drm/amdgpu: fix no bad_pages issue after umc ue injection
drm/amdgpu: fix potential memory leak during navi12 deinitialization
drm/amd/display: Fix unused variable warning
drm/amd/pm: improve the fine grain tuning function for RV/RV2/PCO
drm/amd/pm: fix the failure when change power profile for renoir
drm/amdgpu: fix a GPU hang issue when remove device
drm/amdgpu: fix a memory protection fault when remove amdgpu device
drm/amdgpu: switched to cached noretry setting for vangogh
drm/amd/display: fix sysfs amdgpu_current_backlight_pwm NULL pointer issue
drm/amd/pm: updated PM to I2C controller port on sienna cichlid
...
|
|
Pull kvm fixes from Paolo Bonzini:
"x86:
- Fixes for the new scalable MMU
- Fixes for migration of nested hypervisors on AMD
- Fix for clang integrated assembler
- Fix for left shift by 64 (UBSAN)
- Small cleanups
- Straggler SEV-ES patch
ARM:
- VM init cleanups
- PSCI relay cleanups
- Kill CONFIG_KVM_ARM_PMU
- Fixup __init annotations
- Fixup reg_to_encoding()
- Fix spurious PMCR_EL0 access
Misc:
- selftests cleanups"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (38 commits)
KVM: x86: __kvm_vcpu_halt can be static
KVM: SVM: Add support for booting APs in an SEV-ES guest
KVM: nSVM: cancel KVM_REQ_GET_NESTED_STATE_PAGES on nested vmexit
KVM: nSVM: mark vmcb as dirty when forcingly leaving the guest mode
KVM: nSVM: correctly restore nested_run_pending on migration
KVM: x86/mmu: Clarify TDP MMU page list invariants
KVM: x86/mmu: Ensure TDP MMU roots are freed after yield
kvm: check tlbs_dirty directly
KVM: x86: change in pv_eoi_get_pending() to make code more readable
MAINTAINERS: Really update email address for Sean Christopherson
KVM: x86: fix shift out of bounds reported by UBSAN
KVM: selftests: Implement perf_test_util more conventionally
KVM: selftests: Use vm_create_with_vcpus in create_vm
KVM: selftests: Factor out guest mode code
KVM/SVM: Remove leftover __svm_vcpu_run prototype from svm.c
KVM: SVM: Add register operand to vmsave call in sev_es_vcpu_load
KVM: x86/mmu: Optimize not-present/MMIO SPTE check in get_mmio_spte()
KVM: x86/mmu: Use raw level to index into MMIO walks' sptes array
KVM: x86/mmu: Get root level from walkers when retrieving MMIO SPTE
KVM: x86/mmu: Use -1 to flag an undefined spte in get_mmio_spte()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull iommu fixes from Will Deacon:
"This is mainly all Intel VT-D stuff, but there are some fixes for AMD
and ARM as well.
We've also got the revert I promised during the merge window, which
removes a temporary hack to accomodate i915 while we transitioned the
Intel IOMMU driver over to the common DMA-IOMMU API.
Finally, there are still a couple of other VT-D fixes floating around,
so I expect to send you another batch of fixes next week.
Summary:
- Fix VT-D TLB invalidation for subdevices
- Fix VT-D use-after-free on subdevice detach
- Fix VT-D locking so that IRQs are disabled during SVA bind/unbind
- Fix VT-D address alignment when flushing IOTLB
- Fix memory leak in VT-D IRQ remapping failure path
- Revert temporary i915 sglist hack now that it is no longer required
- Fix sporadic boot failure with Arm SMMU on Qualcomm SM8150
- Fix NULL dereference in AMD IRQ remapping code with remapping disabled
- Fix accidental enabling of irqs on AMD resume-from-suspend path
- Fix some typos in comments"
* tag 'iommu-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
iommu/vt-d: Fix ineffective devTLB invalidation for subdevices
iommu/vt-d: Fix general protection fault in aux_detach_device()
iommu/vt-d: Move intel_iommu info from struct intel_svm to struct intel_svm_dev
iommu/arm-smmu-qcom: Initialize SCTLR of the bypass context
iommu/vt-d: Fix lockdep splat in sva bind()/unbind()
Revert "iommu: Add quirk for Intel graphic devices in map_sg"
iommu/vt-d: Fix misuse of ALIGN in qi_flush_piotlb()
iommu/amd: Stop irq_remapping_select() matching when remapping is disabled
iommu/amd: Set iommu->int_enabled consistently when interrupts are set up
iommu/intel: Fix memleak in intel_irq_remapping_alloc
iommu/iova: fix 'domain' typos
|
|
Pioneer devices have both playback and capture streams sharing the
same iface/altsetting, and those need to be paired as implicit
feedback. Instead of a half-baked (and broken) static quirk entry,
set up more generically for those devices by checking the number of
endpoints and the attribute of the secondary EP.
Fixes: bf6313a0ff76 ("ALSA: usb-audio: Refactor endpoint management")
Reported-by: František Kučera <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
There are devices that have multiple endpoints sharing the same
iface/altset not only for sync but also for the actual streams, and
the audioformat for such an endpoint needs to be handled with the
proper endpoint index; otherwise it confuses the endpoint management.
This patch extends the audioformat to annotate the endpoint index, and
put the proper ep_idx=1 to Pioneer device quirk entries accordingly.
Fixes: bf6313a0ff76 ("ALSA: usb-audio: Refactor endpoint management")
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
The current endpoint handling assumed (more or less) a unique 1:1
relation between the endpoint and the iface/altset. The exception was
the sync EP without the implicit feedback which has usually the
secondary EP of the same altset. This works fine for most devices,
but it turned out that some unusual devices like Pinoeer's ones have
both playback and capture endpoints in the same iface/altsetting and
use both for the implicit feedback mode. For handling such a case, we
need to extend the endpoint management to take the shared interface
into account.
This patch does that: it adds a new object snd_usb_iface_ref for
managing the reference counts of the each USB interface that is used
by each endpoint. The interface setup is performed only once for the
(sharing) endpoints, and the doubly initialization is avoided.
Along with this, the resource release of endpoints and interface
refcounts are put into a single function, snd_usb_endpoint_free_all()
instead of looping in the caller side.
Fixes: bf6313a0ff76 ("ALSA: usb-audio: Refactor endpoint management")
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
The implicit feedback mode needs to handle two endpoints and the
choice of the audioformat object for the sync EP is important since
this determines the compatibility of the hw_params. The current code
uses the same audioformat object if both the main EP and the sync EP
point to the same iface/altsetting. This was done in consideration of
the non-implicit-fb sync EP handling, and it doesn't match well with
the cases where actually to endpoints are defined in the sameiface /
altsetting like a few Pioneer devices.
Modify snd_usb_find_implicit_fb_sync_format() to pick up the
audioformat that is assigned in the counter-part substreams primarily,
so that the actual capture stream can be opened properly. We keep the
same audioformat object only as a fallback in case nothing found,
though.
Fixes: 9fddc15e8039 ("ALSA: usb-audio: Factor out the implicit feedback quirk code")
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
The recent change in the endpoint management moved the endpoint object
creation from the stream open time to the parser of the audio
descriptor. It works fine for the standard audio, but it overlooked
the other places that create audio streams via quirks
(QUIRK_AUDIO_FIXED_ENDPOINT) like the reported a few Pioneer devices;
those call snd_usb_add_audio_stream() manually, hence they miss the
endpoints, eventually resulting in the error at opening streams.
Moreover, now the sync EP setup was moved to the explicit call of
snd_usb_audioformat_set_sync_ep(), and this needs to be added for
those places, too.
This patch addresses those regressions for quirks. It adds a local
helper function add_audio_stream_from_fixed_fmt(), which does the all
needed tasks, and replaces the calls of snd_usb_add_audio_stream()
with this new function.
Fixes: 54cb31901b83 ("ALSA: usb-audio: Create endpoint objects at parsing phase")
Reported-by: František Kučera <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Takashi Iwai <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"These are a small number of bug fixes that all came in before or
during the merge window, most for the omap platform:
- One boot regression fix for Nokia N9 (OMAP3).
- Two small defconfig changes for omap2, to reflect changes in
drivers
- Warning fixes for DT issues on omap2, picoxcell and bitmap SoCs.
The picoxcell platform will be removed in v5.12, but fixing it
first makes it easier to backport to the fix to stable kernels and
get a clean build with new dtc versions"
* tag 'arm-fixes-5.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: picoxcell: fix missing interrupt-parent properties
ARM: dts: ux500/golden: Set display max brightness
arm64: dts: bitmain: Use generic "ngpios" rather than "snps,nr-gpios"
ARM: omap2: pmic-cpcap: fix maximum voltage to be consistent with defaults on xt875
ARM: omap2plus_defconfig: enable SPI GPIO
ARM: OMAP2+: omap_device: fix idling of devices during probe
ARM: dts: OMAP3: disable AES on N950/N9
ARM: omap2plus_defconfig: drop unused POWER_AVS option
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Clean-ups following the merging window: remove unused variable,
duplicate includes, superfluous barrier, move some inline asm to
separate functions.
- Disable top-byte-ignore on kernel code addresses with KASAN/MTE
enabled (already done when MTE is disabled).
- Fix ARCH_LOW_ADDRESS_LIMIT definition with CONFIG_ZONE_DMA disabled.
- Compiler/linker flags: link with "-z norelno", discard .eh_frame_hdr
instead of --no-eh-frame-hdr.
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Move PSTATE.TCO setting to separate functions
arm64: kasan: Set TCR_EL1.TBID1 when KASAN_HW_TAGS is enabled
arm64: vdso: disable .eh_frame_hdr via /DISCARD/ instead of --no-eh-frame-hdr
arm64: traps: remove duplicate include statement
arm64: link with -z norelro for LLD or aarch64-elf
arm64: mm: Fix ARCH_LOW_ADDRESS_LIMIT when !CONFIG_ZONE_DMA
arm64: mte: remove an ISB on kernel exit
arm64/smp: Remove unused irq variable in arch_show_interrupts()
|
|
HSDK has hardware floating point and the common use case is with
glibc+hf so enable that as default.
Signed-off-by: Vineet Gupta <[email protected]>
|
|
With external metadata device, flush requests are not passed down to the
data device.
Fix this by submitting the flush request in dm_integrity_flush_buffers. In
order to not degrade performance, we overlap the data device flush with
the metadata device flush.
Reported-by: Lukas Straub <[email protected]>
Signed-off-by: Mikulas Patocka <[email protected]>
Cc: [email protected]
Signed-off-by: Mike Snitzer <[email protected]>
|
|
There wasn't ever a real need to log an error in the kernel log for
ioctls issued with insufficient permissions. Simply return an error
and if an admin/user is sufficiently motivated they can enable DM's
dynamic debugging to see an explanation for why the ioctls were
disallowed.
Reported-by: Nir Soffer <[email protected]>
Fixes: e980f62353c6 ("dm: don't allow ioctls to targets that don't map to whole devices")
Signed-off-by: Mike Snitzer <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull more networking fixes from Jakub Kicinski:
"Slightly lighter pull request to get back into the Thursday cadence.
Current release - always broken:
- can: mcp251xfd: fix Tx/Rx ring buffer driver race conditions
- dsa: hellcreek: fix led_classdev build errors
Previous releases - regressions:
- ipv6: fib: flush exceptions when purging route to avoid netdev
reference leak
- ip_tunnels: fix pmtu check in nopmtudisc mode
- ip: always refragment ip defragmented packets to avoid MTU issues
when forwarding through tunnels, correct "packet too big" message
is prohibitively tricky to generate
- s390/qeth: fix locking for discipline setup / removal and during
recovery to prevent both deadlocks and races
- mlx5: Use port_num 1 instead of 0 when delete a RoCE address
Previous releases - always broken:
- cdc_ncm: correct overhead calculation in delayed_ndp_size to
prevent out of bound accesses with Huawei 909s-120 LTE module
- fix stmmac dwmac-sun8i suspend/resume:
- PHY being left powered off
- MAC syscon configuration being reset
- reference to the reset controller being improperly dropped
- qrtr: fix null-ptr-deref in qrtr_ns_remove
- can: tcan4x5x: fix bittiming const, use common bittiming from m_can
driver
- mlx5e: CT: Use per flow counter when CT flow accounting is enabled
- mlx5e: Fix SWP offsets when vlan inserted by driver
Misc:
- bpf: Fix a task_iter bug caused by a bpf -> net merge conflict
resolution
And the usual many fixes to various error paths"
* tag 'net-5.11-rc3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (69 commits)
net: dsa: lantiq_gswip: Exclude RMII from modes that report 1 GbE
s390/qeth: fix L2 header access in qeth_l3_osa_features_check()
s390/qeth: fix locking for discipline setup / removal
s390/qeth: fix deadlock during recovery
selftests: fib_nexthops: Fix wrong mausezahn invocation
nexthop: Bounce NHA_GATEWAY in FDB nexthop groups
nexthop: Unlink nexthop group entry in error path
nexthop: Fix off-by-one error in error path
octeontx2-af: fix memory leak of lmac and lmac->name
chtls: Fix chtls resources release sequence
chtls: Added a check to avoid NULL pointer dereference
chtls: Replace skb_dequeue with skb_peek
chtls: Avoid unnecessary freeing of oreq pointer
chtls: Fix panic when route to peer not configured
chtls: Remove invalid set_tcb call
chtls: Fix hardware tid leak
net: ip: always refragment ip defragmented packets
net: fix pmtu check in nopmtudisc mode
selftests: netfilter: add selftest for ipip pmtu discovery with enabled connection tracking
docs: octeontx2: tune rst markup
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
"This fixes a functional bug in arm/chacha-neon as well as a potential
buffer overflow in ecdh"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: ecdh - avoid buffer overflow in ecdh_set_secret()
crypto: arm/chacha-neon - add missing counter increment
|