aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2021-01-12usb: gadget: aspeed: fix stop dma register setting.Ryan Chen1-1/+4
The vhub engine has two dma mode, one is descriptor list, another is single stage DMA. Each mode has different stop register setting. Descriptor list operation (bit2) : 0 disable reset, 1: enable reset Single mode operation (bit0) : 0 : disable, 1: enable Fixes: 7ecca2a4080c ("usb/gadget: Add driver for Aspeed SoC virtual hub") Cc: stable <[email protected]> Acked-by: Felipe Balbi <[email protected]> Acked-by: Joel Stanley <[email protected]> Signed-off-by: Ryan Chen <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-01-12USB: ehci: fix an interrupt calltrace errorLongfang Liu1-0/+3
The system that use Synopsys USB host controllers goes to suspend when using USB audio player. This causes the USB host controller continuous send interrupt signal to system, When the number of interrupts exceeds 100000, the system will forcibly close the interrupts and output a calltrace error. When the system goes to suspend, the last interrupt is reported to the driver. At this time, the system has set the state to suspend. This causes the last interrupt to not be processed by the system and not clear the interrupt flag. This uncleared interrupt flag constantly triggers new interrupt event. This causing the driver to receive more than 100,000 interrupts, which causes the system to forcibly close the interrupt report and report the calltrace error. so, when the driver goes to sleep and changes the system state to suspend, the interrupt flag needs to be cleared. Signed-off-by: Longfang Liu <[email protected]> Acked-by: Alan Stern <[email protected]> Link: https://lore.kernel.org/r/[email protected] Cc: stable <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-01-12ehci: fix EHCI host controller initialization sequenceEugene Korenevsky1-0/+12
According to EHCI spec, EHCI HC clears USBSTS.HCHalted whenever USBCMD.RS=1. However, it is a good practice to wait some time after setting USBCMD.RS (approximately 100ms) until USBSTS.HCHalted become zero. Without this waiting, VirtualBox's EHCI virtual HC accidentally hangs (see BugLink). BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=211095 Acked-by: Alan Stern <[email protected]> Signed-off-by: Eugene Korenevsky <[email protected]> Cc: stable <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2021-01-12Merge tag 'thunderbolt-for-v5.11-rc4' of ↵Greg Kroah-Hartman1-1/+1
git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-linus Mika writes: thunderbolt: Fix for v5.11-rc4 This includes a single format string fix for the firmware connection manager USB4 NVM authentication proxy implementation introduced in this merge window. * tag 'thunderbolt-for-v5.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt: thunderbolt: Drop duplicated 0x prefix from format string
2021-01-12ia64: Mark architecture as orphanedArnd Bergmann1-4/+1
Tony Luck has maintained arch/ia64 for the past 16 years, but mentioned that he no longer has working ia64 machines, nor time to look at patches, so he is stepping down as the maintainer. Fenghua Yu came in as a temporary co-maintainer when Tony was on sabbatical in 2009, but has not worked on it after that either. This leaves the architecture as Orphaned, meaning that patches will have to get routed through other trees from now on. Acked-by: Tony Luck <[email protected]> Cc: Fenghua Yu <[email protected]> Cc: [email protected] Link: https://lore.kernel.org/lkml/[email protected]/ Signed-off-by: Arnd Bergmann <[email protected]>
2021-01-12ia64: fix xchg() warningArnd Bergmann1-1/+1
The definition if xchg() causes a harmless warning in some files, like: In file included from ../arch/ia64/include/uapi/asm/intrinsics.h:22, from ../arch/ia64/include/asm/intrinsics.h:11, from ../arch/ia64/include/asm/bitops.h:19, from ../include/linux/bitops.h:32, from ../include/linux/kernel.h:11, from ../fs/nfs/read.c:12: ../fs/nfs/read.c: In function 'nfs_read_completion': ../arch/ia64/include/uapi/asm/cmpxchg.h:57:2: warning: value computed is not used [-Wunused-value] 57 | ((__typeof__(*(ptr))) __xchg((unsigned long) (x), (ptr), sizeof(*(ptr)))) | ~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ ../fs/nfs/read.c:196:5: note: in expansion of macro 'xchg' 196 | xchg(&nfs_req_openctx(req)->error, error); | ^~~~ Change it to a compound expression like the other architectures have to get a clean defconfig build. Signed-off-by: Arnd Bergmann <[email protected]>
2021-01-12ia64: fix timer cleanup regressionArnd Bergmann1-13/+18
A cleanup patch from my legacy timer series broke ia64 and led to RCU stall errors and a fast system clock: [ 909.360108] INFO: task systemd-sysv-ge:200 blocked for more than 127 seconds. [ 909.360108] Not tainted 5.10.0+ #130 [ 909.360108] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 909.360108] task:systemd-sysv-ge state:D stack: 0 pid: 200 ppid: 189 flags:0x00000000 [ 909.364108] [ 909.364108] Call Trace: [ 909.364423] [<a00000010109b210>] __schedule+0x890/0x21e0 [ 909.364423] sp=e0000100487d7b70 bsp=e0000100487d1748 [ 909.368423] [<a00000010109cc00>] schedule+0xa0/0x240 [ 909.368423] sp=e0000100487d7b90 bsp=e0000100487d16e0 [ 909.368558] [<a00000010109ce70>] io_schedule+0x70/0xa0 [ 909.368558] sp=e0000100487d7b90 bsp=e0000100487d16c0 [ 909.372290] [<a00000010109e1c0>] bit_wait_io+0x20/0xe0 [ 909.372290] sp=e0000100487d7b90 bsp=e0000100487d1698 [ 909.374168] rcu: INFO: rcu_sched detected stalls on CPUs/tasks: [ 909.376290] [<a00000010109d860>] __wait_on_bit+0xc0/0x1c0 [ 909.376290] sp=e0000100487d7b90 bsp=e0000100487d1648 [ 909.374168] rcu: 3-....: (2 ticks this GP) idle=19e/1/0x4000000000000002 softirq=1581/1581 fqs=2 [ 909.374168] (detected by 0, t=5661 jiffies, g=1089, q=3) [ 909.376290] [<a00000010109da80>] out_of_line_wait_on_bit+0x120/0x140 [ 909.376290] sp=e0000100487d7b90 bsp=e0000100487d1610 [ 909.374168] Task dump for CPU 3: [ 909.374168] task:khungtaskd state:R running task Revert most of my patch to make this work again, including the extra update_process_times()/profile_tick() and the local_irq_enable() in the loop that I expected not to be needed here. I have not found out exactly what goes wrong, and would suggest that someone with hardware access tries to convert this code into a singleshot clockevent driver, which should give better behavior in all cases. Reported-by: John Paul Adrian Glaubitz <[email protected]> Fixes: 2b49ddcef297 ("ia64: convert to legacy_timer_tick") Cc: John Stultz <[email protected]> Cc: Thomas Gleixner <[email protected]> Cc: Stephen Boyd <[email protected]> Cc: Frederic Weisbecker <[email protected]> Signed-off-by: Arnd Bergmann <[email protected]>
2021-01-12iommu: arm-smmu-qcom: Add sdm630/msm8998 compatibles for qcom quirksKonrad Dybcio1-0/+2
SDM630 and MSM8998 are among the SoCs that use Qualcomm's implementation of SMMUv2 which has already proven to be problematic over the years. Add their compatibles to the lookup list to prevent the platforms from being shut down by the hypervisor at MMU probe. Signed-off-by: Konrad Dybcio <[email protected]> Signed-off-by: AngeloGioacchino Del Regno <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Will Deacon <[email protected]>
2021-01-12iommu/vt-d: Fix unaligned addresses for intel_flush_svm_range_dev()Lu Baolu1-2/+20
The VT-d hardware will ignore those Addr bits which have been masked by the AM field in the PASID-based-IOTLB invalidation descriptor. As the result, if the starting address in the descriptor is not aligned with the address mask, some IOTLB caches might not invalidate. Hence people will see below errors. [ 1093.704661] dmar_fault: 29 callbacks suppressed [ 1093.704664] DMAR: DRHD: handling fault status reg 3 [ 1093.712738] DMAR: [DMA Read] Request device [7a:02.0] PASID 2 fault addr 7f81c968d000 [fault reason 113] SM: Present bit in first-level paging entry is clear Fix this by using aligned address for PASID-based-IOTLB invalidation. Fixes: 1c4f88b7f1f9 ("iommu/vt-d: Shared virtual address in scalable mode") Reported-and-tested-by: Guo Kaijie <[email protected]> Signed-off-by: Lu Baolu <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Will Deacon <[email protected]>
2021-01-12bpf: Update local storage test to check handling of null ptrsKP Singh2-97/+61
It was found in [1] that bpf_inode_storage_get helper did not check the nullness of the passed owner ptr which caused an oops when dereferenced. This change incorporates the example suggested in [1] into the local storage selftest. The test is updated to create a temporary directory instead of just using a tempfile. In order to replicate the issue this copied rm binary is renamed tiggering the inode_rename with a null pointer for the new_inode. The logic to verify the setting and deletion of the inode local storage of the old inode is also moved to this LSM hook. The change also removes the copy_rm function and simply shells out to copy files and recursively delete directories and consolidates the logic of setting the initial inode storage to the bprm_committed_creds hook and removes the file_open hook. [1]: https://lore.kernel.org/bpf/CANaYP3HWkH91SN=wTNO9FL_2ztHfqcXKX38SSE-JJ2voh+vssw@mail.gmail.com Suggested-by: Gilad Reti <[email protected]> Signed-off-by: KP Singh <[email protected]> Signed-off-by: Daniel Borkmann <[email protected]> Acked-by: Yonghong Song <[email protected]> Link: https://lore.kernel.org/bpf/[email protected]
2021-01-12bpf: Fix typo in bpf_inode_storage.cKP Singh1-2/+2
Fix "gurranteed" -> "guaranteed" in bpf_inode_storage.c Suggested-by: Andrii Nakryiko <[email protected]> Signed-off-by: KP Singh <[email protected]> Signed-off-by: Daniel Borkmann <[email protected]> Acked-by: Yonghong Song <[email protected]> Link: https://lore.kernel.org/bpf/[email protected]
2021-01-12bpf: Local storage helpers should check nullness of owner ptr passedKP Singh2-2/+8
The verifier allows ARG_PTR_TO_BTF_ID helper arguments to be NULL, so helper implementations need to check this before dereferencing them. This was already fixed for the socket storage helpers but not for task and inode. The issue can be reproduced by attaching an LSM program to inode_rename hook (called when moving files) which tries to get the inode of the new file without checking for its nullness and then trying to move an existing file to a new path: mv existing_file new_file_does_not_exist The report including the sample program and the steps for reproducing the bug: https://lore.kernel.org/bpf/CANaYP3HWkH91SN=wTNO9FL_2ztHfqcXKX38SSE-JJ2voh+vssw@mail.gmail.com Fixes: 4cf1bc1f1045 ("bpf: Implement task local storage") Fixes: 8ea636848aca ("bpf: Implement bpf_local_storage for inodes") Reported-by: Gilad Reti <[email protected]> Signed-off-by: KP Singh <[email protected]> Signed-off-by: Daniel Borkmann <[email protected]> Acked-by: Martin KaFai Lau <[email protected]> Acked-by: Yonghong Song <[email protected]> Link: https://lore.kernel.org/bpf/[email protected]
2021-01-12ALSA: hda/hdmi - enable runtime pm for CI AMD display audioAlex Deucher1-3/+6
We are able to power down the GPU and audio via the GPU driver so flag these asics as supporting runtime pm. Reviewed-by: Evan Quan <[email protected]> Signed-off-by: Alex Deucher <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Takashi Iwai <[email protected]>
2021-01-12media: Revert "media: videobuf2: Fix length check for single plane dmabuf ↵Naushir Patuck1-2/+1
queueing" The updated length check for dmabuf types broke existing usage in v4l2 userland clients. Fixes: 961d3b27 ("media: videobuf2: Fix length check for single plane dmabuf queueing") Cc: [email protected] Signed-off-by: Naushir Patuck <[email protected]> Tested-by: Kieran Bingham <[email protected]> Reviewed-by: Kieran Bingham <[email protected]> Reviewed-by: Laurent Pinchart <[email protected]> Signed-off-by: Hans Verkuil <[email protected]> Signed-off-by: Mauro Carvalho Chehab <[email protected]>
2021-01-12Merge tag 'usb-v5.11-rc3' of ↵Greg Kroah-Hartman2-14/+14
git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-linus Peter writes: - Several bug-fixes for cdns3 imx driver - Update Peter Chen and Roger Quadros email address * tag 'usb-v5.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb: MAINTAINERS: update Peter Chen's email address MAINTAINERS: Update address for Cadence USB3 driver usb: cdns3: imx: improve driver .remove API usb: cdns3: imx: fix can't create core device the second time issue usb: cdns3: imx: fix writing read-only memory issue
2021-01-12btrfs: send: fix invalid clone operations when cloning from the same file ↵Filipe Manana1-0/+15
and root When an incremental send finds an extent that is shared, it checks which file extent items in the range refer to that extent, and for those it emits clone operations, while for others it emits regular write operations to avoid corruption at the destination (as described and fixed by commit d906d49fc5f4 ("Btrfs: send, fix file corruption due to incorrect cloning operations")). However when the root we are cloning from is the send root, we are cloning from the inode currently being processed and the source file range has several extent items that partially point to the desired extent, with an offset smaller than the offset in the file extent item for the range we want to clone into, it can cause the algorithm to issue a clone operation that starts at the current eof of the file being processed in the receiver side, in which case the receiver will fail, with EINVAL, when attempting to execute the clone operation. Example reproducer: $ cat test-send-clone.sh #!/bin/bash DEV=/dev/sdi MNT=/mnt/sdi mkfs.btrfs -f $DEV >/dev/null mount $DEV $MNT # Create our test file with a single and large extent (1M) and with # different content for different file ranges that will be reflinked # later. xfs_io -f \ -c "pwrite -S 0xab 0 128K" \ -c "pwrite -S 0xcd 128K 128K" \ -c "pwrite -S 0xef 256K 256K" \ -c "pwrite -S 0x1a 512K 512K" \ $MNT/foobar btrfs subvolume snapshot -r $MNT $MNT/snap1 btrfs send -f /tmp/snap1.send $MNT/snap1 # Now do a series of changes to our file such that we end up with # different parts of the extent reflinked into different file offsets # and we overwrite a large part of the extent too, so no file extent # items refer to that part that was overwritten. This used to confuse # the algorithm used by the kernel to figure out which file ranges to # clone, making it attempt to clone from a source range starting at # the current eof of the file, resulting in the receiver to fail since # it is an invalid clone operation. # xfs_io -c "reflink $MNT/foobar 64K 1M 960K" \ -c "reflink $MNT/foobar 0K 512K 256K" \ -c "reflink $MNT/foobar 512K 128K 256K" \ -c "pwrite -S 0x73 384K 640K" \ $MNT/foobar btrfs subvolume snapshot -r $MNT $MNT/snap2 btrfs send -f /tmp/snap2.send -p $MNT/snap1 $MNT/snap2 echo -e "\nFile digest in the original filesystem:" md5sum $MNT/snap2/foobar # Now unmount the filesystem, create a new one, mount it and try to # apply both send streams to recreate both snapshots. umount $DEV mkfs.btrfs -f $DEV >/dev/null mount $DEV $MNT btrfs receive -f /tmp/snap1.send $MNT btrfs receive -f /tmp/snap2.send $MNT # Must match what we got in the original filesystem of course. echo -e "\nFile digest in the new filesystem:" md5sum $MNT/snap2/foobar umount $MNT When running the reproducer, the incremental send operation fails due to an invalid clone operation: $ ./test-send-clone.sh wrote 131072/131072 bytes at offset 0 128 KiB, 32 ops; 0.0015 sec (80.906 MiB/sec and 20711.9741 ops/sec) wrote 131072/131072 bytes at offset 131072 128 KiB, 32 ops; 0.0013 sec (90.514 MiB/sec and 23171.6148 ops/sec) wrote 262144/262144 bytes at offset 262144 256 KiB, 64 ops; 0.0025 sec (98.270 MiB/sec and 25157.2327 ops/sec) wrote 524288/524288 bytes at offset 524288 512 KiB, 128 ops; 0.0052 sec (95.730 MiB/sec and 24506.9883 ops/sec) Create a readonly snapshot of '/mnt/sdi' in '/mnt/sdi/snap1' At subvol /mnt/sdi/snap1 linked 983040/983040 bytes at offset 1048576 960 KiB, 1 ops; 0.0006 sec (1.419 GiB/sec and 1550.3876 ops/sec) linked 262144/262144 bytes at offset 524288 256 KiB, 1 ops; 0.0020 sec (120.192 MiB/sec and 480.7692 ops/sec) linked 262144/262144 bytes at offset 131072 256 KiB, 1 ops; 0.0018 sec (133.833 MiB/sec and 535.3319 ops/sec) wrote 655360/655360 bytes at offset 393216 640 KiB, 160 ops; 0.0093 sec (66.781 MiB/sec and 17095.8436 ops/sec) Create a readonly snapshot of '/mnt/sdi' in '/mnt/sdi/snap2' At subvol /mnt/sdi/snap2 File digest in the original filesystem: 9c13c61cb0b9f5abf45344375cb04dfa /mnt/sdi/snap2/foobar At subvol snap1 At snapshot snap2 ERROR: failed to clone extents to foobar: Invalid argument File digest in the new filesystem: 132f0396da8f48d2e667196bff882cfc /mnt/sdi/snap2/foobar The clone operation is invalid because its source range starts at the current eof of the file in the receiver, causing the receiver to get an EINVAL error from the clone operation when attempting it. For the example above, what happens is the following: 1) When processing the extent at file offset 1M, the algorithm checks that the extent is shared and can be (fully or partially) found at file offset 0. At this point the file has a size (and eof) of 1M at the receiver; 2) It finds that our extent item at file offset 1M has a data offset of 64K and, since the file extent item at file offset 0 has a data offset of 0, it issues a clone operation, from the same file and root, that has a source range offset of 64K, destination offset of 1M and a length of 64K, since the extent item at file offset 0 refers only to the first 128K of the shared extent. After this clone operation, the file size (and eof) at the receiver is increased from 1M to 1088K (1M + 64K); 3) Now there's still 896K (960K - 64K) of data left to clone or write, so it checks for the next file extent item, which starts at file offset 128K. This file extent item has a data offset of 0 and a length of 256K, so a clone operation with a source range offset of 256K, a destination offset of 1088K (1M + 64K) and length of 128K is issued. After this operation the file size (and eof) at the receiver increases from 1088K to 1216K (1088K + 128K); 4) Now there's still 768K (896K - 128K) of data left to clone or write, so it checks for the next file extent item, located at file offset 384K. This file extent item points to a different extent, not the one we want to clone, with a length of 640K. So we issue a write operation into the file range 1216K (1088K + 128K, end of the last clone operation), with a length of 640K and with a data matching the one we can find for that range in send root. After this operation, the file size (and eof) at the receiver increases from 1216K to 1856K (1216K + 640K); 5) Now there's still 128K (768K - 640K) of data left to clone or write, so we look into the file extent item, which is for file offset 1M and it points to the extent we want to clone, with a data offset of 64K and a length of 960K. However this matches the file offset we started with, the start of the range to clone into. So we can't for sure find any file extent item from here onwards with the rest of the data we want to clone, yet we proceed and since the file extent item points to the shared extent, with a data offset of 64K, we issue a clone operation with a source range starting at file offset 1856K, which matches the file extent item's offset, 1M, plus the amount of data cloned and written so far, which is 64K (step 2) + 128K (step 3) + 640K (step 4). This clone operation is invalid since the source range offset matches the current eof of the file in the receiver. We should have stopped looking for extents to clone at this point and instead fallback to write, which would simply the contain the data in the file range from 1856K to 1856K + 128K. So fix this by stopping the loop that looks for file ranges to clone at clone_range() when we reach the current eof of the file being processed, if we are cloning from the same file and using the send root as the clone root. This ensures any data not yet cloned will be sent to the receiver through a write operation. A test case for fstests will follow soon. Reported-by: Massimo B. <[email protected]> Link: https://lore.kernel.org/linux-btrfs/[email protected]/ Fixes: 11f2069c113e ("Btrfs: send, allow clone operations within the same file") CC: [email protected] # 5.5+ Reviewed-by: Josef Bacik <[email protected]> Signed-off-by: Filipe Manana <[email protected]> Signed-off-by: David Sterba <[email protected]>
2021-01-12btrfs: no need to run delayed refs after commit_fs_roots during commitDavid Sterba1-8/+0
The inode number cache has been removed in this dev cycle, there's one more leftover. We don't need to run the delayed refs again after commit_fs_roots as stated in the comment, because btrfs_save_ino_cache is no more since 5297199a8bca ("btrfs: remove inode number cache feature"). Nothing else between commit_fs_roots and btrfs_qgroup_account_extents could create new delayed refs so the qgroup consistency should be safe. Reviewed-by: Nikolay Borisov <[email protected]> Signed-off-by: David Sterba <[email protected]>
2021-01-12ALSA: firewire-tascam: Fix integer overflow in midi_port_work()Geert Uytterhoeven1-1/+1
As snd_fw_async_midi_port.consume_bytes is unsigned int, and NSEC_PER_SEC is 1000000000L, the second multiplication in port->consume_bytes * 8 * NSEC_PER_SEC / 31250 always overflows on 32-bit platforms, truncating the result. Fix this by precalculating "NSEC_PER_SEC / 31250", which is an integer constant. Note that this assumes port->consume_bytes <= 16777. Fixes: 531f471834227d03 ("ALSA: firewire-lib/firewire-tascam: localize async midi port") Reviewed-by: Takashi Sakamoto <[email protected]> Signed-off-by: Geert Uytterhoeven <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Takashi Iwai <[email protected]>
2021-01-12ALSA: fireface: Fix integer overflow in transmit_midi_msg()Geert Uytterhoeven1-1/+1
As snd_ff.rx_bytes[] is unsigned int, and NSEC_PER_SEC is 1000000000L, the second multiplication in ff->rx_bytes[port] * 8 * NSEC_PER_SEC / 31250 always overflows on 32-bit platforms, truncating the result. Fix this by precalculating "NSEC_PER_SEC / 31250", which is an integer constant. Note that this assumes ff->rx_bytes[port] <= 16777. Fixes: 19174295788de77d ("ALSA: fireface: add transaction support") Reviewed-by: Takashi Sakamoto <[email protected]> Signed-off-by: Geert Uytterhoeven <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Takashi Iwai <[email protected]>
2021-01-12nfsd4: readdirplus shouldn't return parent of exportJ. Bruce Fields1-1/+6
If you export a subdirectory of a filesystem, a READDIRPLUS on the root of that export will return the filehandle of the parent with the ".." entry. The filehandle is optional, so let's just not return the filehandle for ".." if we're at the root of an export. Note that once the client learns one filehandle outside of the export, they can trivially access the rest of the export using further lookups. However, it is also not very difficult to guess filehandles outside of the export. So exporting a subdirectory of a filesystem should considered equivalent to providing access to the entire filesystem. To avoid confusion, we recommend only exporting entire filesystems. Reported-by: Youjipeng <[email protected]> Signed-off-by: J. Bruce Fields <[email protected]> Cc: [email protected] Signed-off-by: Chuck Lever <[email protected]>
2021-01-12ALSA: hda/tegra: fix tegra-hda on tegra30 socPeter Geis1-1/+1
Currently hda on tegra30 fails to open a stream with an input/output error. For example: speaker-test -Dhw:0,3 -c 2 speaker-test 1.2.2 Playback device is hw:0,3 Stream parameters are 48000Hz, S16_LE, 2 channels Using 16 octaves of pink noise Rate set to 48000Hz (requested 48000Hz) Buffer size range from 64 to 16384 Period size range from 32 to 8192 Using max buffer size 16384 Periods = 4 was set period_size = 4096 was set buffer_size = 16384 0 - Front Left Write error: -5,Input/output error xrun_recovery failed: -5,Input/output error Transfer failed: Input/output error The tegra-hda device was introduced in tegra30 but only utilized in tegra124 until recent chips. Tegra210/186 work only due to a hardware change. For this reason it is unknown when this issue first manifested. Discussions with the hardware team show this applies to all current tegra chips. It has been resolved in the tegra234, which does not have hda support at this time. The explanation from the hardware team is this: Below is the striping formula referenced from HD audio spec. { ((num_channels * bits_per_sample) / number of SDOs) >= 8 } The current issue is seen because Tegra HW has a problem with boundary condition (= 8) for striping. The reason why it is not seen on Tegra210/Tegra186 is because it uses max 2SDO lines. Max SDO lines is read from GCAP register. For the given stream (channels = 2, bps = 16); ratio = (channels * bps) / NSDO = 32 / NSDO; On Tegra30, ratio = 32/4 = 8 (FAIL) On Tegra210/186, ratio = 32/2 = 16 (PASS) On Tegra194, ratio = 32/4 = 8 (FAIL) ==> Earlier workaround was applied for it If Tegra210/186 is forced to use 4SDO, it fails there as well. So the behavior is consistent across all these chips. Applying the fix in [1] universally resolves this issue on tegra30-hda. Tested on the Ouya game console and the tf201 tablet. [1] commit 60019d8c650d ("ALSA: hda/tegra: workaround playback failure on Tegra194") Reviewed-by: Jon Hunter <[email protected]> Tested-by: Ion Agorria <[email protected]> Reviewed-by: Sameer Pujar <[email protected]> Acked-by: Thierry Reding <[email protected]> Signed-off-by: Peter Geis <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Takashi Iwai <[email protected]>
2021-01-12clk: tegra30: Add hda clock default rates to clock driverPeter Geis1-0/+2
Current implementation defaults the hda clocks to clk_m. This causes hda to run too slow to operate correctly. Fix this by defaulting to pll_p and setting the frequency to the correct rate. This matches upstream t124 and downstream t30. Acked-by: Jon Hunter <[email protected]> Tested-by: Ion Agorria <[email protected]> Acked-by: Sameer Pujar <[email protected]> Acked-by: Thierry Reding <[email protected]> Signed-off-by: Peter Geis <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Takashi Iwai <[email protected]>
2021-01-12drm/ttm: make the pool shrinker lock a mutexChristian König1-10/+10
set_pages_wb() might sleep and so we can't do this in an atomic context. Signed-off-by: Christian König <[email protected]> Reported-by: Mikhail Gavrilov <[email protected]> Tested-by: Mikhail Gavrilov <[email protected]> Fixes: d099fc8f540a ("drm/ttm: new TT backend allocation pool v3") Reviewed-by: Huang Rui <[email protected]> Link: https://patchwork.freedesktop.org/patch/413409/
2021-01-12habanalabs: prevent soft lockup during unmapOded Gabbay3-5/+12
When using Deep learning framework such as tensorflow or pytorch, there are tens of thousands of host memory mappings. When the user frees all those mappings at the same time, the process of unmapping and unpinning them can take a long time, which may cause a soft lockup bug. To prevent this, we need to free the core to do other things during the unmapping process. For now, we chose to do it every 32K unmappings (each unmap is a single 4K page). Signed-off-by: Oded Gabbay <[email protected]>
2021-01-12habanalabs: fix reset process in case of failuresOded Gabbay2-3/+11
There are some points in the reset process where if the code fails for some reason, and the system admin tries to initiate the reset process again we will get a kernel panic. This is because there aren't any protections in different fini functions that are called during the reset process. The protections that are added in this patch make sure that if the fini functions are called multiple times, without calling init functions between them, there won't be double release of already released resources. Signed-off-by: Oded Gabbay <[email protected]>
2021-01-12habanalabs: fix dma_addr passed to dma_mmap_coherentOded Gabbay2-2/+4
When doing dma_alloc_coherent in the driver, we add a certain hard-coded offset to the DMA address before returning to the callee function. This offset is needed when our device use this DMA address to perform outbound transactions to the host. However, if we want to map the DMA'able memory to the user via dma_mmap_coherent(), we need to pass the original dma address, without this offset. Otherwise, we will get erronouos mapping. Signed-off-by: Oded Gabbay <[email protected]>
2021-01-12media: rc: ite-cir: fix min_timeout calculationMatthias Reichl1-1/+1
Commit 528222d853f92 ("media: rc: harmonize infrared durations to microseconds") missed to switch the min_timeout calculation from ns to us. This resulted in a minimum timeout of 1.2 seconds instead of 1.2ms, leading to large delays and long key repeats. Fix this by applying proper ns->us conversion. Cc: [email protected] Fixes: 528222d853f92 ("media: rc: harmonize infrared durations to microseconds") Signed-off-by: Matthias Reichl <[email protected]> Signed-off-by: Sean Young <[email protected]> Signed-off-by: Mauro Carvalho Chehab <[email protected]>
2021-01-12x86/cpu/amd: Set __max_die_per_package on AMDYazen Ghannam1-2/+2
Set the maximum DIE per package variable on AMD using the NodesPerProcessor topology value. This will be used by RAPL, among others, to determine the maximum number of DIEs on the system in order to do per-DIE manipulations. [ bp: Productize into a proper patch. ] Fixes: 028c221ed190 ("x86/CPU/AMD: Save AMD NodeId as cpu_die_id") Reported-by: Johnathan Smithinovic <[email protected]> Reported-by: Rafael Kitover <[email protected]> Signed-off-by: Yazen Ghannam <[email protected]> Signed-off-by: Borislav Petkov <[email protected]> Tested-by: Johnathan Smithinovic <[email protected]> Tested-by: Rafael Kitover <[email protected]> Link: https://bugzilla.kernel.org/show_bug.cgi?id=210939 Link: https://lkml.kernel.org/r/[email protected] Link: https://lkml.kernel.org/r/[email protected]
2021-01-12ALSA: doc: Fix reference to mixart.rstJonathan Neuschäfer1-1/+1
MIXART.txt has been converted to ReST and renamed. Fix the reference in alsa-configuration.rst. Fixes: 3d8e81862ce4 ("ALSA: doc: ReSTize MIXART.txt") Signed-off-by: Jonathan Neuschäfer <[email protected]> Cc: <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Takashi Iwai <[email protected]>
2021-01-12powerpc: Fix alignment bug within the init sectionsAriel Marcovitch1-0/+8
This is a bug that causes early crashes in builds with an .exit.text section smaller than a page and an .init.text section that ends in the beginning of a physical page (this is kinda random, which might explain why this wasn't really encountered before). The init sections are ordered like this: .init.text .exit.text .init.data Currently, these sections aren't page aligned. Because the init code might become read-only at runtime and because the .init.text section can potentially reside on the same physical page as .init.data, the beginning of .init.data might be mapped read-only along with .init.text. Then when the kernel tries to modify a variable in .init.data (like kthreadd_done, used in kernel_init()) the kernel panics. To avoid this, make _einittext page aligned and also align .exit.text to make sure .init.data is always seperated from the text segments. Fixes: 060ef9d89d18 ("powerpc32: PAGE_EXEC required for inittext") Signed-off-by: Ariel Marcovitch <[email protected]> Reviewed-by: Christophe Leroy <[email protected]> Signed-off-by: Michael Ellerman <[email protected]> Link: https://lore.kernel.org/r/[email protected]
2021-01-11Merge branch 'skb-frag-kmap_atomic-fixes'Jakub Kicinski4-18/+27
Willem de Bruijn says: ==================== skb frag: kmap_atomic fixes skb frags may be backed by highmem and/or compound pages. Various code calls kmap_atomic to safely access highmem pages. But this needs additional care for compound pages. Fix a few issues: patch 1 expect kmap mappings with CONFIG_DEBUG_KMAP_LOCAL_FORCE_MAP patch 2 fixes kmap_atomic + compound page support in skb_seq_read patch 3 fixes kmap_atomic + compound page support in esp ==================== Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2021-01-11esp: avoid unneeded kmap_atomic callWillem de Bruijn2-12/+2
esp(6)_output_head uses skb_page_frag_refill to allocate a buffer for the esp trailer. It accesses the page with kmap_atomic to handle highmem. But skb_page_frag_refill can return compound pages, of which kmap_atomic only maps the first underlying page. skb_page_frag_refill does not return highmem, because flag __GFP_HIGHMEM is not set. ESP uses it in the same manner as TCP. That also does not call kmap_atomic, but directly uses page_address, in skb_copy_to_page_nocache. Do the same for ESP. This issue has become easier to trigger with recent kmap local debugging feature CONFIG_DEBUG_KMAP_LOCAL_FORCE_MAP. Fixes: cac2661c53f3 ("esp4: Avoid skb_cow_data whenever possible") Fixes: 03e2a30f6a27 ("esp6: Avoid skb_cow_data whenever possible") Signed-off-by: Willem de Bruijn <[email protected]> Acked-by: Steffen Klassert <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
2021-01-11net: compound page support in skb_seq_readWillem de Bruijn2-5/+24
skb_seq_read iterates over an skb, returning pointer and length of the next data range with each call. It relies on kmap_atomic to access highmem pages when needed. An skb frag may be backed by a compound page, but kmap_atomic maps only a single page. There are not enough kmap slots to always map all pages concurrently. Instead, if kmap_atomic is needed, iterate over each page. As this increases the number of calls, avoid this unless needed. The necessary condition is captured in skb_frag_must_loop. I tried to make the change as obvious as possible. It should be easy to verify that nothing changes if skb_frag_must_loop returns false. Tested: On an x86 platform with CONFIG_HIGHMEM=y CONFIG_DEBUG_KMAP_LOCAL_FORCE_MAP=y CONFIG_NETFILTER_XT_MATCH_STRING=y Run ip link set dev lo mtu 1500 iptables -A OUTPUT -m string --string 'badstring' -algo bm -j ACCEPT dd if=/dev/urandom of=in bs=1M count=20 nc -l -p 8000 > /dev/null & nc -w 1 -q 0 localhost 8000 < in Signed-off-by: Willem de Bruijn <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
2021-01-11net: support kmap_local forced debugging in skb_frag_foreachWillem de Bruijn1-1/+1
Skb frags may be backed by highmem and/or compound pages. Highmem pages need kmap_atomic mappings to access. But kmap_atomic maps a single page, not the entire compound page. skb_foreach_page iterates over an skb frag, in one step in the common case, page by page only if kmap_atomic must be called for each page. The decision logic is captured in skb_frag_must_loop. CONFIG_DEBUG_KMAP_LOCAL_FORCE_MAP extends kmap from highmem to all pages, to increase code coverage. Extend skb_frag_must_loop to this new condition. Link: https://lore.kernel.org/linux-mm/[email protected]/ Fixes: 0e91a0c6984c ("mm/highmem: Provide CONFIG_DEBUG_KMAP_LOCAL_FORCE_MAP") Reported-by: Steven Rostedt (VMware) <[email protected]> Signed-off-by: Linus Torvalds <[email protected]> Signed-off-by: Willem de Bruijn <[email protected]> Tested-by: Steven Rostedt (VMware) <[email protected]> Signed-off-by: Jakub Kicinski <[email protected]>
2021-01-11rndis_host: set proper input size for OID_GEN_PHYSICAL_MEDIUM requestAndrey Zhizhikin1-1/+1
MSFT ActiveSync implementation requires that the size of the response for incoming query is to be provided in the request input length. Failure to set the input size proper results in failed request transfer, where the ActiveSync counterpart reports the NDIS_STATUS_INVALID_LENGTH (0xC0010014L) error. Set the input size for OID_GEN_PHYSICAL_MEDIUM query to the expected size of the response in order for the ActiveSync to properly respond to the request. Fixes: 039ee17d1baa ("rndis_host: Add RNDIS physical medium checking into generic_rndis_bind()") Signed-off-by: Andrey Zhizhikin <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2021-01-11net: mvpp2: Remove Pause and Asym_Pause supportStefan Chulski1-2/+0
Packet Processor hardware not connected to MAC flow control unit and cannot support TX flow control. This patch disable flow control support. Fixes: 3f518509dedc ("ethernet: Add new driver for Marvell Armada 375 network unit") Signed-off-by: Stefan Chulski <[email protected]> Acked-by: Marcin Wojtas <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2021-01-11dt-bindings: net: dwmac: fix queue priority documentationSeb Laveze1-2/+6
The priority field is not the queue priority (queue priority is fixed) but a bitmask of priorities assigned to this queue. In receive, priorities relate to tagged frames priorities. In transmit, priorities relate to PFC frames. Signed-off-by: Seb Laveze <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>
2021-01-12bpf: Prevent double bpf_prog_put call from bpf_tracing_prog_attachJiri Olsa1-2/+4
The bpf_tracing_prog_attach error path calls bpf_prog_put on prog, which causes refcount underflow when it's called from link_create function. link_create prog = bpf_prog_get <-- get ... tracing_bpf_link_attach(prog.. bpf_tracing_prog_attach(prog.. out_put_prog: bpf_prog_put(prog); <-- put if (ret < 0) bpf_prog_put(prog); <-- put Removing bpf_prog_put call from bpf_tracing_prog_attach and making sure its callers call it instead. Fixes: 4a1e7c0c63e0 ("bpf: Support attaching freplace programs to multiple attach points") Signed-off-by: Jiri Olsa <[email protected]> Signed-off-by: Daniel Borkmann <[email protected]> Acked-by: Toke Høiland-Jørgensen <[email protected]> Acked-by: Andrii Nakryiko <[email protected]> Link: https://lore.kernel.org/bpf/[email protected]
2021-01-11Merge tag 'trace-v5.11-rc2' of ↵Linus Torvalds2-2/+2
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace Pull tracing fix from Steven Rostedt: "Blacklist properly on all archs. The code to blacklist notrace functions for kprobes was not using the right kconfig option, which caused some archs (powerpc) to possibly not blacklist them" * tag 'trace-v5.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: tracing/kprobes: Do the notrace functions check without kprobes on ftrace
2021-01-11Merge tag 'for-5.11-rc3-tag' of ↵Linus Torvalds8-29/+67
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux Pull btrfs fixes from David Sterba: "More material for stable trees. - tree-checker: check item end overflow - fix false warning during relocation regarding extent type - fix inode flushing logic, caused notable performance regression (since 5.10) - debugging fixups: - print correct offset for reloc tree key - pass reliable fs_info pointer to error reporting helper" * tag 'for-5.11-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux: btrfs: shrink delalloc pages instead of full inodes btrfs: reloc: fix wrong file extent type check to avoid false ENOENT btrfs: tree-checker: check if chunk item end overflows btrfs: prevent NULL pointer dereference in extent_io_tree_panic btrfs: print the actual offset in btrfs_root_name
2021-01-11scsi: target: Fix XCOPY NAA identifier lookupDavid Disseldorp2-49/+71
When attempting to match EXTENDED COPY CSCD descriptors with corresponding se_devices, target_xcopy_locate_se_dev_e4() currently iterates over LIO's global devices list which includes all configured backstores. This change ensures that only initiator-accessible backstores are considered during CSCD descriptor lookup, according to the session's se_node_acl LUN list. To avoid LUN removal race conditions, device pinning is changed from being configfs based to instead using the se_node_acl lun_ref. Reference: CVE-2020-28374 Fixes: cbf031f425fd ("target: Add support for EXTENDED_COPY copy offload emulation") Reviewed-by: Lee Duncan <[email protected]> Signed-off-by: David Disseldorp <[email protected]> Signed-off-by: Mike Christie <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]>
2021-01-11i2c: tegra: Wait for config load atomically while in ISRMikko Perttunen1-1/+1
Upon a communication error, the interrupt handler can call tegra_i2c_disable_packet_mode. This causes a sleeping poll to happen unless the current transaction was marked atomic. Fix this by making the poll happen atomically if we are in an IRQ. This matches the behavior prior to the patch mentioned in the Fixes tag. Fixes: ede2299f7101 ("i2c: tegra: Support atomic transfers") Cc: [email protected] Signed-off-by: Mikko Perttunen <[email protected]> Reviewed-by: Dmitry Osipenko <[email protected]> Signed-off-by: Wolfram Sang <[email protected]>
2021-01-11drm: Check actual format for legacy pageflip.Bas Nieuwenhuizen1-1/+8
With modifiers one can actually have different format_info structs for the same format, which now matters for AMDGPU since we convert implicit modifiers to explicit modifiers with multiple planes. I checked other drivers and it doesn't look like they end up triggering this case so I think this is safe to relax. Signed-off-by: Bas Nieuwenhuizen <[email protected]> Reviewed-by: Daniel Vetter <[email protected]> Reviewed-by: Zhan Liu <[email protected]> Acked-by: Christian König <[email protected]> Acked-by: Alex Deucher <[email protected]> Fixes: 816853f9dc40 ("drm/amd/display: Set new format info for converted metadata.") Signed-off-by: Alex Deucher <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
2021-01-11tracing/kprobes: Do the notrace functions check without kprobes on ftraceMasami Hiramatsu2-2/+2
Enable the notrace function check on the architecture which doesn't support kprobes on ftrace but support dynamic ftrace. This notrace function check is not only for the kprobes on ftrace but also sw-breakpoint based kprobes. Thus there is no reason to limit this check for the arch which supports kprobes on ftrace. This also changes the dependency of Kconfig. Because kprobe event uses the function tracer's address list for identifying notrace function, if the CONFIG_DYNAMIC_FTRACE=n, it can not check whether the target function is notrace or not. Link: https://lkml.kernel.org/r/[email protected] Link: https://lkml.kernel.org/r/161007957862.114704.4512260007555399463.stgit@devnote2 Cc: [email protected] Fixes: 45408c4f92506 ("tracing: kprobes: Prohibit probing on notrace function") Acked-by: Naveen N. Rao <[email protected]> Signed-off-by: Masami Hiramatsu <[email protected]> Signed-off-by: Steven Rostedt (VMware) <[email protected]>
2021-01-11drm/ttm: Fix address passed to dma_mapping_error() in ttm_pool_map()Jeremy Cline1-1/+1
check_unmap() is producing a warning about a missing map error check. The return value from dma_map_page() should be checked for an error, not the caller-provided dma_addr. Fixes: d099fc8f540a ("drm/ttm: new TT backend allocation pool v3") Signed-off-by: Jeremy Cline <[email protected]> Reviewed-by: Christian König <[email protected]> Link: https://patchwork.freedesktop.org/patch/413432/ Signed-off-by: Christian König <[email protected]>
2021-01-11ACPI: scan: Harden acpi_device_add() against device ID overflowsDexuan Cui2-2/+15
Linux VM on Hyper-V crashes with the latest mainline: [ 4.069624] detected buffer overflow in strcpy [ 4.077733] kernel BUG at lib/string.c:1149! .. [ 4.085819] RIP: 0010:fortify_panic+0xf/0x11 ... [ 4.085819] Call Trace: [ 4.085819] acpi_device_add.cold.15+0xf2/0xfb [ 4.085819] acpi_add_single_object+0x2a6/0x690 [ 4.085819] acpi_bus_check_add+0xc6/0x280 [ 4.085819] acpi_ns_walk_namespace+0xda/0x1aa [ 4.085819] acpi_walk_namespace+0x9a/0xc2 [ 4.085819] acpi_bus_scan+0x78/0x90 [ 4.085819] acpi_scan_init+0xfa/0x248 [ 4.085819] acpi_init+0x2c1/0x321 [ 4.085819] do_one_initcall+0x44/0x1d0 [ 4.085819] kernel_init_freeable+0x1ab/0x1f4 This is because of the recent buffer overflow detection in the commit 6a39e62abbaf ("lib: string.h: detect intra-object overflow in fortified string functions") Here acpi_device_bus_id->bus_id can only hold 14 characters, while the the acpi_device_hid(device) returns a 22-char string "HYPER_V_GEN_COUNTER_V1". Per ACPI Spec v6.2, Section 6.1.5 _HID (Hardware ID), if the ID is a string, it must be of the form AAA#### or NNNN####, i.e. 7 chars or 8 chars. The field bus_id in struct acpi_device_bus_id was originally defined as char bus_id[9], and later was enlarged to char bus_id[15] in 2007 in the commit bb0958544f3c ("ACPI: use more understandable bus_id for ACPI devices") Fix the issue by changing the field bus_id to const char *, and use kstrdup_const() to initialize it. Signed-off-by: Dexuan Cui <[email protected]> Tested-By: Jethro Beekman <[email protected]> [ rjw: Subject change, whitespace adjustment ] Cc: All applicable <[email protected]> Signed-off-by: Rafael J. Wysocki <[email protected]>
2021-01-11Merge tag 'nfsd-5.11-1' of git://git.linux-nfs.org/projects/cel/cel-2.6Linus Torvalds5-28/+126
Pull nfsd fixes from Chuck Lever: - Fix major TCP performance regression - Get NFSv4.2 READ_PLUS regression tests to pass - Improve NFSv4 COMPOUND memory allocation - Fix sparse warning * tag 'nfsd-5.11-1' of git://git.linux-nfs.org/projects/cel/cel-2.6: NFSD: Restore NFSv4 decoding's SAVEMEM functionality SUNRPC: Handle TCP socket sends with kernel_sendpage() again NFSD: Fix sparse warning in nfssvc.c nfsd: Don't set eof on a truncated READ_PLUS nfsd: Fixes for nfsd4_encode_read_plus_data()
2021-01-11Merge tag 'hyperv-fixes-signed-20210111' of ↵Linus Torvalds5-5/+33
git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux Pull hyperv fixes from Wei Liu: - fix kexec panic/hang (Dexuan Cui) - fix occasional crashes when flushing TLB (Wei Liu) * tag 'hyperv-fixes-signed-20210111' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux: x86/hyperv: check cpu mask after interrupt has been disabled x86/hyperv: Fix kexec panic/hang issues
2021-01-11x86/sev-es: Handle string port IO to kernel memory properlyHyunwook (Wooky) Baek1-0/+12
Don't assume dest/source buffers are userspace addresses when manually copying data for string I/O or MOVS MMIO, as {get,put}_user() will fail if handed a kernel address and ultimately lead to a kernel panic. When invoking INSB/OUTSB instructions in kernel space in a SEV-ES-enabled VM, the kernel crashes with the following message: "SEV-ES: Unsupported exception in #VC instruction emulation - can't continue" Handle that case properly. [ bp: Massage commit message. ] Fixes: f980f9c31a92 ("x86/sev-es: Compile early handler code into kernel image") Signed-off-by: Hyunwook (Wooky) Baek <[email protected]> Signed-off-by: Borislav Petkov <[email protected]> Acked-by: David Rientjes <[email protected]> Link: https://lkml.kernel.org/r/[email protected]
2021-01-11Merge tag 'gvt-fixes-2020-01-08' of https://github.com/intel/gvt-linux into ↵Jani Nikula2-27/+59
drm-intel-fixes gvt-fixes-2020-01-08 - Fix VFIO EDID on APL/BXT (Colin) Signed-off-by: Jani Nikula <[email protected]> From: Zhenyu Wang <[email protected]> Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
Powered by cgit, Gruvboxed by Blaster4385.