| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This is ABI future-proofing if we ever want to extend the pad to mean
something.
Signed-off-by: Eric Anholt <[email protected]>
|
|
There is presently a race condition between the bonding periodic
link monitor and the updating of a slave's speed and duplex. The former
occurs on a periodic basis, and the latter in response to a driver's
calling of netif_carrier_on.
It is possible for the periodic monitor to run between the
driver call of netif_carrier_on and the receipt of the NETDEV_CHANGE
event that causes bonding to update the slave's speed and duplex. This
manifests most notably as a report that a slave is up and "0 Mbps full
duplex" after enslavement, but in principle could report an incorrect
speed and duplex after any link up event if the device comes up with a
different speed or duplex. This affects the 802.3ad aggregator
selection, as the speed and duplex are selection criteria.
This is fixed by updating the speed and duplex in the periodic
monitor, prior to using that information.
This was done historically in bonding, but the call to
bond_update_speed_duplex was removed in commit 876254ae2758 ("bonding:
don't call update_speed_duplex() under spinlocks"), as it might sleep
under lock. Later, the locking was changed to only hold RTNL, and so
after commit 876254ae2758 ("bonding: don't call update_speed_duplex()
under spinlocks") this call is again safe.
Tested-by: "Tantilov, Emil S" <[email protected]>
Cc: Veaceslav Falico <[email protected]>
Cc: dingtianhong <[email protected]>
Fixes: 876254ae2758 ("bonding: don't call update_speed_duplex() under spinlocks")
Signed-off-by: Jay Vosburgh <[email protected]>
Acked-by: Ding Tianhong <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The am79c961a.c driver fails to build with clang because of an
unusual inline assembly construct:
drivers/net/ethernet/amd/am79c961a.c:53:7: error: invalid % escape in inline assembly string
"str%?h %1, [%2] @ NET_RAP\n\t"
The same change has been done a decade ago in arch/arm as of
6a39dd6222dd ("[ARM] 3759/2: Remove uses of %?"), but apparently
some drivers were missed.
Signed-off-by: Arnd Bergmann <[email protected]>
Acked-by: Russell King <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The smc91x driver doesn't honor the probe deferral mechanism when the
interrupt source is not yet available, such as one provided by a gpio
controller not probed.
Fix this by propagating the platform_get_irq() error code as the probe
return value.
Signed-off-by: Robert Jarzmik <[email protected]>
Cc: Sergei Shtylyov <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Florian Fainelli says:
====================
Subject: [PATCH net v2 0/4] net: phy: bcm7xxx 40nm PHY fixes
Here is a collection of fixes for the 40nm Ethernet PHY supported
by the 7xxx PHY driver, please also queue these fixes for stable.
Changes in v2:
- dropped the cleanup patch, not appropriate
- added another patch removing bogus wildcard entries
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
Remove the two wildcard entries, they serve no purpose and will match way too
many devices, some of them being covered by the driver in
drivers/net/phy/broadcom.c. Remove the now unused bcm7xxx_dummy_config_init()
function which would produce a warning.
Fixes: b560a58c45c6 ("net: phy: add Broadcom BCM7xxx internal PHY driver")
Signed-off-by: Florian Fainelli <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Since we were wrongly advertising gigabit features for these 10/100 only
Ethernet PHYs, bcm7xxx_config_init() which is supposed to apply workaround
would have not run since the check would be true, now that we have fixed the
PHY features, remove that check since it has no reasoning to be there anymore.
Fixes: e18556ee3bd83 ("net: phy: bcm7xxx: do not use PHY_BRCM_100MBPS_WAR")
Signed-off-by: Florian Fainelli <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The PHY entries for BCM7425/29/35 declare the 40nm Ethernet PHY as being
10/100/1000 capable, while this is just a 10/100 capable PHY device, fix that.
Fixes: d068b02cfdfc2 ("net: phy: add BCM7425 and BCM7429 PHYs")
Fixes: 9458ceab4917 ("net: phy: bcm7xxx: Add entry for BCM7435")
Signed-off-by: Florian Fainelli <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The clear and set masks in the call to phy_set_clr_bits() called from
bcm7xxx_config_init() are inverted. We need to fix this by swapping the two
arguments, that is, set 0 bits, but clear the shade mode 2 enable bit.
Fixes: b560a58c45c66 ("net: phy: add Broadcom BCM7xxx internal PHY driver")
Signed-off-by: Florian Fainelli <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Sergei Shtylyov says:
====================
ravb: fix the fallout of R-Car gen3 gPTP support
Here's a set of 2 patches against DaveM's 'net.git' repo fixing up the
incomplete commit f5d7837f96e5 ("ravb: ptp: Add CONFIG mode support").
I'm proposing these as fixes but they can be merged as cleanups as well...
[1/2] ravb: kill duplicate setting of CCC.CSEL
[2/2] ravb: skip gPTP start/stop on R-Car gen3
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
When adding support for the R-Car gen3 gPTP active in configuration mode,
some call sites of ravb_ptp_{init|stop}() were missed due to an oversight.
Add checks for the R-Car gen2 SoCs around these...
Fixes: f5d7837f96e5 ("ravb: ptp: Add CONFIG mode support")
Signed-off-by: Sergei Shtylyov <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
When adding support for the R-Car gen3 gPTP active in configuration mode,
the code setting the CCC.CSEL field was duplicated due to an oversight.
For R-Car gen 2 it's just redundant and for R-Car gen3 the write at this
time is probably ignored due to CCC.GAC bit being already set...
Fixes: f5d7837f96e5 ("ravb: ptp: Add CONFIG mode support")
Signed-off-by: Sergei Shtylyov <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Pull cifs fixes from Steve French:
"A small set of cifs fixes.
I am still reviewing some more, recently submitted SMB3 fixes, but
these three are small and safe and ready now"
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
cifs: fix erroneous return value
cifs: fix potential overflow in cifs_compose_mount_options
cifs: remove redundant check for null string pointer
|
|
Pull ARM KVM fixes from Paolo Bonzini:
- Fix for an unpleasant crash when the VM is created without a timer
- Allow HYP mode to access the full PA space, and not only 40bit
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
arm64: KVM: Configure TCR_EL2.PS at runtime
KVM: arm/arm64: Fix reference to uninitialised VGIC
|
|
If cgroup writeback is in use, an inode is associated with a cgroup
for writeback. If the inode's main dirtier changes to another cgroup,
the association gets updated asynchronously. Nothing was pinning the
superblock while such switches are in progress and superblock could go
away while async switching is pending or in progress leading to
crashes like the following.
kernel BUG at fs/jbd2/transaction.c:319!
invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC
CPU: 1 PID: 29158 Comm: kworker/1:10 Not tainted 4.5.0-rc3 #51
Hardware name: Google Google, BIOS Google 01/01/2011
Workqueue: events inode_switch_wbs_work_fn
task: ffff880213dbbd40 ti: ffff880209264000 task.ti: ffff880209264000
RIP: 0010:[<ffffffff803e6922>] [<ffffffff803e6922>] start_this_handle+0x382/0x3e0
RSP: 0018:ffff880209267c30 EFLAGS: 00010202
...
Call Trace:
[<ffffffff803e6be4>] jbd2__journal_start+0xf4/0x190
[<ffffffff803cfc7e>] __ext4_journal_start_sb+0x4e/0x70
[<ffffffff803b31ec>] ext4_evict_inode+0x12c/0x3d0
[<ffffffff8035338b>] evict+0xbb/0x190
[<ffffffff80354190>] iput+0x130/0x190
[<ffffffff80360223>] inode_switch_wbs_work_fn+0x343/0x4c0
[<ffffffff80279819>] process_one_work+0x129/0x300
[<ffffffff80279b16>] worker_thread+0x126/0x480
[<ffffffff8027ed14>] kthread+0xc4/0xe0
[<ffffffff809771df>] ret_from_fork+0x3f/0x70
Fix it by bumping s_active while cgroup association switching is in
flight.
Signed-off-by: Tejun Heo <[email protected]>
Reported-and-tested-by: Tahsin Erdogan <[email protected]>
Link: http://lkml.kernel.org/g/CAAeU0aNCq7LGODvVGRU-oU_o-6enii5ey0p1c26D1ZzYwkDc5A@mail.gmail.com
Fixes: d10c80955265 ("writeback: implement foreign cgroup inode bdi_writeback switching")
Cc: [email protected] #v4.5+
Signed-off-by: Jens Axboe <[email protected]>
|
|
The irq-armada-370-xp driver can only be built for ARM 32 bits. The mvebu
family had grown with a new ARM64 SoC which will also select the
ARCH_MEVBU configuration. Since "ARM: mvebu: use the ARMADA_370_XP_IRQ
option", the ARM32 mvebu SoC directly select this new option. Selecting
it by default when ARCH_MEVBU is selected is no more needed.
This patch removes this dependency, thanks to this, a kernel for ARM64
mvebu SoC can be built without error due this driver.
Signed-off-by: Gregory CLEMENT <[email protected]>
Link: https://lkml.kernel.org/r/1454951660-13289-3-git-send-email-gregory.clement@free-electrons.com
Signed-off-by: Jason Cooper <[email protected]>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contain a rather large batch for your net that
includes accumulated bugfixes, they are:
1) Run conntrack cleanup from workqueue process context to avoid hitting
soft lockup via watchdog for large tables. This is required by the
IPv6 masquerading extension. From Florian Westphal.
2) Use original skbuff from nfnetlink batch when calling netlink_ack()
on error since this needs to access the skb->sk pointer.
3) Incremental fix on top of recent Sasha Levin's lock fix for conntrack
resizing.
4) Fix several problems in nfnetlink batch message header sanitization
and error handling, from Phil Turnbull.
5) Select NF_DUP_IPV6 based on CONFIG_IPV6, from Arnd Bergmann.
6) Fix wrong signess in return values on nf_tables counter expression,
from Anton Protopopov.
Due to the NetDev 1.1 organization burden, I had no chance to pass up
this to you any sooner in this release cycle, sorry about that.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
The unix_dgram_sendmsg routine use the following test
if (unlikely(unix_peer(other) != sk && unix_recvq_full(other))) {
to determine if sk and other are in an n:1 association (either
established via connect or by using sendto to send messages to an
unrelated socket identified by address). This isn't correct as the
specified address could have been bound to the sending socket itself or
because this socket could have been connected to itself by the time of
the unix_peer_get but disconnected before the unix_state_lock(other). In
both cases, the if-block would be entered despite other == sk which
might either block the sender unintentionally or lead to trying to unlock
the same spin lock twice for a non-blocking send. Add a other != sk
check to guard against this.
Fixes: 7d267278a9ec ("unix: avoid use-after-free in ep_remove_wait_queue")
Reported-By: Philipp Hahn <[email protected]>
Signed-off-by: Rainer Weikusat <[email protected]>
Tested-by: Philipp Hahn <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into kvm-master
KVM/ARM fixes for 4.5-rc4
- Fix for an unpleasant crash when the VM is created without a timer
- Allow HYP mode to access the full PA space, and not only 40bit
|
|
The present unix_stream_read_generic contains various code sequences of
the form
err = -EDISASTER;
if (<test>)
goto out;
This has the unfortunate side effect of possibly causing the error code
to bleed through to the final
out:
return copied ? : err;
and then to be wrongly returned if no data was copied because the caller
didn't supply a data buffer, as demonstrated by the program available at
http://pad.lv/1540731
Change it such that err is only set if an error condition was detected.
Fixes: 3822b5c2fc62 ("af_unix: Revert 'lock_interruptible' in stream receive code")
Reported-by: Joseph Salisbury <[email protected]>
Signed-off-by: Rainer Weikusat <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Now that there is a ARMADA_370_XP_IRQ option to enable the irqchip
driver for Armada 370, XP, 375, 38x and 39x, let's select this option
when needed. Note that this selection is currently not mandatory
because ARMADA_370_XP_IRQ is for now always enabled when ARCH_MVEBU=y,
but this is something that we will change in the future, and therefore
we should make the relevant platforms select ARMADA_370_XP_IRQ when
needed.
Due to this, selecting GENERIC_IRQ_CHIP is no longer needed.
Signed-off-by: Thomas Petazzoni <[email protected]>
Acked-by: Gregory CLEMENT <[email protected]>
Link: https://lkml.kernel.org/r/1455115621-22846-7-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <[email protected]>
|
|
Add support for allocating multiple MSIs at the same time, so that the
MSI_FLAG_MULTI_PCI_MSI flag can be added to the msi_domain_info
structure.
Signed-off-by: Thomas Petazzoni <[email protected]>
Reviewed-by: Gregory CLEMENT <[email protected]>
Link: https://lkml.kernel.org/r/1455115621-22846-6-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <[email protected]>
|
|
In order to make the output of /proc/interrupts, use shorter names for
the irq_chip registered by the irq-armada-370-xp driver. Using capital
letters also matches better what is done for the GIC driver, which
uses just "GIC" as the irq_chip->name.
Signed-off-by: Thomas Petazzoni <[email protected]>
Acked-by: Gregory CLEMENT <[email protected]>
Link: https://lkml.kernel.org/r/1455115621-22846-5-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <[email protected]>
|
|
As suggested by Gregory Clement, this commit adjusts the
irq-armada-370-xp driver to use the PCI_MSI_DOORBELL_START define in
the armada_370_xp_handle_msi_irq() function, rather than hardcoding
its value.
Suggested-by: Gregory CLEMENT <[email protected]>
Signed-off-by: Thomas Petazzoni <[email protected]>
Acked-by: Gregory CLEMENT <[email protected]>
Link: https://lkml.kernel.org/r/1455115621-22846-4-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <[email protected]>
|
|
This commit moves the irq-armada-370-xp driver from using the
PCI-specific MSI infrastructure to the generic MSI infrastructure, to
which drivers are progressively converted.
In this hardware, the MSI controller is directly bundled inside the
interrupt controller, so we have a single Device Tree node to which
multiple IRQ domaines are attached: the wired interrupt domain and the
MSI interrupt domain. In order to ensure that they can be
differentiated, we have to force the bus_token of the wired interrupt
domain to be DOMAIN_BUS_WIRED. The MSI domain bus_token is
automatically set to the appropriate value by
pci_msi_create_irq_domain().
Signed-off-by: Thomas Petazzoni <[email protected]>
Suggested-by: Marc Zyngier <[email protected]>
Reviewed-by: Marc Zyngier <[email protected]>
Link: https://lkml.kernel.org/r/1455115621-22846-3-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <[email protected]>
|
|
Instead of building the irq-armada-370-xp driver directly when
CONFIG_ARCH_MVEBU is enabled, this commit introduces an intermediate
CONFIG_ARMADA_370_XP_IRQ hidden Kconfig option.
This allows this option to select other interrupt-related Kconfig
options (which will be needed in follow-up commits) rather than having
such selects done from arch/arm/mach-<foo>/.
Signed-off-by: Thomas Petazzoni <[email protected]>
Acked-by: Gregory CLEMENT <[email protected]>
Link: https://lkml.kernel.org/r/1455115621-22846-2-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <[email protected]>
|
|
Pull IOMMU SVM fixes from David Woodhouse:
"Minor register size and interrupt acknowledgement fixes which only
showed up in testing on newer hardware, but mostly a fix to the MM
refcount handling to prevent a recursive refcount issue when mmap() is
used on the file descriptor associated with a bound PASID"
* tag 'for-linus-20160216' of git://git.infradead.org/intel-iommu:
iommu/vt-d: Clear PPR bit to ensure we get more page request interrupts
iommu/vt-d: Fix 64-bit accesses to 32-bit DMAR_GSTS_REG
iommu/vt-d: Fix mm refcounting to hold mm_count not mm_users
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
These are a few fixes for the current cycle.
3 out of the 5 patches fix a bugzilla.
* fix a race that users reported when we try to load the firmware
and the hardware rfkill interrupt triggers at the same time.
* Luca fixes a very visible bug in scheduled scan: our firmware
doesn't support scheduled scan with no profile configured and
the supplicant sometimes requests such scheduled scans.
* build system fix
* firmware name update for 8265
* typo fix in return value
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mfleming/efi into x86/urgent
Pull EFI bug fixes from Matt Fleming:
* Fix bugs in our code that converts ucs2 strings to utf8 where we
unintentionally drop bits from the original string (Jason Andryuk)
* Add the efi-pstore variables to the variable whitelist so that
users can continue to delete them via efivarfs without needing to
manipulate the immutable flag (Matt Fleming)
Signed-off-by: Ingo Molnar <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A small clutch of driver specific fixes.
The OMAP one is a bit worrying since it seems to be triggered by some
changes in the runtime PM core code and I suspect there's other
drivers across that are going to be using the same pattern outside of
OMAP but nothing seems to be coming up in the testing people are
doing"
* tag 'spi-fix-v4.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: omap2-mcspi: Fix PM regression with deferred probe for pm_runtime_reinit
spi: bcm2835aux: fix bitmask defines
spi: atmel: fix gpio chip-select in case of non-DT platform
spi/fsl-espi: Correct the maximum transaction length
spi: imx: fix spi resource leak with dma transfer
spi: fix counting in spi-loopback-test code
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k fixes from Geert Uytterhoeven:
"Summary:
- Wire up new copy_file_range syscall
- Update defconfigs"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k/defconfig: Update defconfigs for v4.5-rc1
m68k: Wire up copy_file_range
|
|
We need to use post-decrement to get the pci_map_page undone also for
i==0, and to avoid some very unpleasant behaviour if pci_map_page
failed already at i==0.
Reviewed-by: Christian König <[email protected]>
Signed-off-by: Rasmus Villemoes <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
Cc: [email protected]
|
|
We need to use post-decrement to get the pci_map_page undone also for
i==0, and to avoid some very unpleasant behaviour if pci_map_page
failed already at i==0.
Reviewed-by: Christian König <[email protected]>
Signed-off-by: Rasmus Villemoes <[email protected]>
Signed-off-by: Alex Deucher <[email protected]>
Cc: [email protected]
|
|
batman-adv checks in different situation if a new device is already on top
of a different batman-adv device. This is done by getting the iflink of a
device and all its parent. It assumes that this iflink is always a parent
device in an acyclic graph. But this assumption is broken by devices like
veth which are actually a pair of two devices linked to each other. The
recursive check would therefore get veth0 when calling dev_get_iflink on
veth1. And it gets veth0 when calling dev_get_iflink with veth1.
Creating a veth pair and loading batman-adv freezes parts of the system
ip link add veth0 type veth peer name veth1
modprobe batman-adv
An RCU stall will be detected on the system which cannot be fixed.
INFO: rcu_sched self-detected stall on CPU
1: (5264 ticks this GP) idle=3e9/140000000000001/0
softirq=144683/144686 fqs=5249
(t=5250 jiffies g=46 c=45 q=43)
Task dump for CPU 1:
insmod R running task 0 247 245 0x00000008
ffffffff8151f140 ffffffff8107888e ffff88000fd141c0 ffffffff8151f140
0000000000000000 ffffffff81552df0 ffffffff8107b420 0000000000000001
ffff88000e3fa700 ffffffff81540b00 ffffffff8107d667 0000000000000001
Call Trace:
<IRQ> [<ffffffff8107888e>] ? rcu_dump_cpu_stacks+0x7e/0xd0
[<ffffffff8107b420>] ? rcu_check_callbacks+0x3f0/0x6b0
[<ffffffff8107d667>] ? hrtimer_run_queues+0x47/0x180
[<ffffffff8107cf9d>] ? update_process_times+0x2d/0x50
[<ffffffff810873fb>] ? tick_handle_periodic+0x1b/0x60
[<ffffffff810290ae>] ? smp_trace_apic_timer_interrupt+0x5e/0x90
[<ffffffff813bbae2>] ? apic_timer_interrupt+0x82/0x90
<EOI> [<ffffffff812c3fd7>] ? __dev_get_by_index+0x37/0x40
[<ffffffffa0031f3e>] ? batadv_hard_if_event+0xee/0x3a0 [batman_adv]
[<ffffffff812c5801>] ? register_netdevice_notifier+0x81/0x1a0
[...]
This can be avoided by checking if two devices are each others parent and
stopping the check in this situation.
Fixes: b7eddd0b3950 ("batman-adv: prevent using any virtual device created on batman-adv as hard-interface")
Signed-off-by: Andrew Lunn <[email protected]>
[[email protected]: rewritten description, extracted fix]
Signed-off-by: Sven Eckelmann <[email protected]>
Signed-off-by: Marek Lindner <[email protected]>
Signed-off-by: Antonio Quartulli <[email protected]>
|
|
The commit [7f0973e973cd: ALSA: seq: Fix lockdep warnings due to
double mutex locks] split the management of two linked lists (source
and destination) into two individual calls for avoiding the AB/BA
deadlock. However, this may leave the possible double deletion of one
of two lists when the counterpart is being deleted concurrently.
It ends up with a list corruption, as revealed by syzkaller fuzzer.
This patch fixes it by checking the list emptiness and skipping the
deletion and the following process.
BugLink: http://lkml.kernel.org/r/CACT4Y+bay9qsrz6dQu31EcGaH9XwfW7o3oBzSQUG9fMszoh=Sg@mail.gmail.com
Fixes: 7f0973e973cd ('ALSA: seq: Fix lockdep warnings due to 'double mutex locks)
Reported-by: Dmitry Vyukov <[email protected]>
Tested-by: Dmitry Vyukov <[email protected]>
Cc: <[email protected]>
Signed-off-by: Takashi Iwai <[email protected]>
|
|
The comparisons should be >= since 0x800 and 0x80 require an additional bit
to store.
For the 3 byte case, the existing shift would drop off 2 more bits than
intended.
For the 2 byte case, there should be 5 bits bits in byte 1, and 6 bits in
byte 2.
Signed-off-by: Jason Andryuk <[email protected]>
Reviewed-by: Laszlo Ersek <[email protected]>
Cc: Peter Jones <[email protected]>
Cc: Matthew Garrett <[email protected]>
Cc: "Lee, Chun-Yi" <[email protected]>
Signed-off-by: Matt Fleming <[email protected]>
|
|
Laszlo explains why this is a good idea,
'This is because the pstore filesystem can be backed by UEFI variables,
and (for example) a crash might dump the last kilobytes of the dmesg
into a number of pstore entries, each entry backed by a separate UEFI
variable in the above GUID namespace, and with a variable name
according to the above pattern.
Please see "drivers/firmware/efi/efi-pstore.c".
While this patch series will not prevent the user from deleting those
UEFI variables via the pstore filesystem (i.e., deleting a pstore fs
entry will continue to delete the backing UEFI variable), I think it
would be nice to preserve the possibility for the sysadmin to delete
Linux-created UEFI variables that carry portions of the crash log,
*without* having to mount the pstore filesystem.'
There's also no chance of causing machines to become bricked by
deleting these variables, which is the whole purpose of excluding
things from the whitelist.
Use the LINUX_EFI_CRASH_GUID guid and a wildcard '*' for the match so
that we don't have to update the string in the future if new variable
name formats are created for crash dump variables.
Reported-by: Laszlo Ersek <[email protected]>
Acked-by: Peter Jones <[email protected]>
Tested-by: Peter Jones <[email protected]>
Cc: Matthew Garrett <[email protected]>
Cc: "Lee, Chun-Yi" <[email protected]>
Signed-off-by: Matt Fleming <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mfleming/efi into x86/urgent
Pull EFI fixes from Matt Fleming:
* Prevent accidental deletion of EFI variables through efivarfs that
may brick machines. We use a whitelist of known-safe variables to
allow things like installing distributions to work out of the box, and
instead restrict vendor-specific variable deletion by making
non-whitelist variables immutable (Peter Jones)
Signed-off-by: Ingo Molnar <[email protected]>
|
|
The 5 volt detect functionality broke in 3.14: the code reads IO register 0x70
again after it has already been cleared. Instead it should use the cached
irq_reg_0x70 value and the io_write to 0x71 to clear 0x70 can be dropped since
this has already been done.
Signed-off-by: Hans Verkuil <[email protected]>
Cc: <[email protected]> # for v3.14 and up
Signed-off-by: Mauro Carvalho Chehab <[email protected]>
|
|
Defining it as a connector was a bad idea. Remove it while it is
not too late.
Signed-off-by: Mauro Carvalho Chehab <[email protected]>
|
|
Each function range is quite narrow and especially for connectors this
will pose a problem. Increase the function ranges while we still can and
move the connector range to the end so that range is practically limitless.
[[email protected]: Rebased to apply at Linus tree]
Signed-off-by: Hans Verkuil <[email protected]>
Signed-off-by: Mauro Carvalho Chehab <[email protected]>
|
|
Changes introduced in the upstream version of libfdt pulled in by commit
91feabc2e224 ("scripts/dtc: Update to upstream commit b06e55c88b9b") use
the strnlen() function, which isn't currently available to the EFI name-
space. Add it to the EFI namespace to avoid a linker error.
Cc: Catalin Marinas <[email protected]>
Cc: Rob Herring <[email protected]>
Reviewed-by: Ard Biesheuvel <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
Signed-off-by: Will Deacon <[email protected]>
|
|
The batadv_orig_node_vlan reference counter in batadv_tt_global_size_mod
can only be reduced when the list entry was actually removed. Otherwise the
reference counter may reach zero when batadv_tt_global_size_mod is called
from two different contexts for the same orig_node_vlan but only one
context is actually removing the entry from the list.
The release function for this orig_node_vlan is not called inside the
vlan_list_lock spinlock protected region because the function
batadv_tt_global_size_mod still holds a orig_node_vlan reference for the
object pointer on the stack. Thus the actual release function (when
required) will be called only at the end of the function.
Fixes: 7ea7b4a14275 ("batman-adv: make the TT CRC logic VLAN specific")
Signed-off-by: Sven Eckelmann <[email protected]>
Signed-off-by: Marek Lindner <[email protected]>
Signed-off-by: Antonio Quartulli <[email protected]>
|
|
The batadv_gw_node reference counter in batadv_gw_node_update can only be
reduced when the list entry was actually removed. Otherwise the reference
counter may reach zero when batadv_gw_node_update is called from two
different contexts for the same gw_node but only one context is actually
removing the entry from the list.
The release function for this gw_node is not called inside the list_lock
spinlock protected region because the function batadv_gw_node_update still
holds a gw_node reference for the object pointer on the stack. Thus the
actual release function (when required) will be called only at the end of
the function.
Fixes: bd3524c14bd0 ("batman-adv: remove obsolete deleted attribute for gateway node")
Signed-off-by: Sven Eckelmann <[email protected]>
Signed-off-by: Marek Lindner <[email protected]>
Signed-off-by: Antonio Quartulli <[email protected]>
|
|
Until this patch, when TXing non-sta the pending_frames counter
wasn't increased, but it WAS decreased in
iwl_mvm_rx_tx_cmd_single(), what makes it negative in certain
conditions. This in turn caused much trouble when we need to
remove the station since we won't be waiting forever until
pending_frames gets 0. In certain cases, we were exhausting
the station table even in BSS mode, because we had a lot of
stale stations.
Increase the counter also in iwl_mvm_tx_skb_non_sta() after a
successful TX to avoid this outcome.
CC: <[email protected]> [3.18+]
Signed-off-by: Liad Kaufman <[email protected]>
Signed-off-by: Emmanuel Grumbach <[email protected]>
|
|
When ext4_bread() fails, fname_crypto_str remains
allocated after return. Fix that.
Signed-off-by: Kirill Tkhai <[email protected]>
Signed-off-by: Theodore Ts'o <[email protected]>
CC: Dmitry Monakhov <[email protected]>
|
|
If a bio for a direct IO request fails, we were not setting the error in
the parent bio (the main DIO bio), making us not return the error to
user space in btrfs_direct_IO(), that is, it made __blockdev_direct_IO()
return the number of bytes issued for IO and not the error a bio created
and submitted by btrfs_submit_direct() got from the block layer.
This essentially happens because when we call:
dio_end_io(dio_bio, bio->bi_error);
It does not set dio_bio->bi_error to the value of the second argument.
So just add this missing assignment in endio callbacks, just as we do in
the error path at btrfs_submit_direct() when we fail to clone the dio bio
or allocate its private object. This follows the convention of what is
done with other similar APIs such as bio_endio() where the caller is
responsible for setting the bi_error field in the bio it passes as an
argument to bio_endio().
This was detected by the new generic test cases in xfstests: 271, 272,
276 and 278. Which essentially setup a dm error target, then load the
error table, do a direct IO write and unload the error table. They
expect the write to fail with -EIO, which was not getting reported
when testing against btrfs.
Cc: [email protected] # 4.3+
Fixes: 4246a0b63bd8 ("block: add a bi_error field to struct bio")
Signed-off-by: Filipe Manana <[email protected]>
|
|
Previously, samsung_gpio_drection_in/output function were not covered
with a spinlock.
For example, samsung_gpio_direction_output function consists of
two functions.
1. samsung_gpio_set
2. samsung_gpio_set_direction
When 2 CPUs try to control the same gpio pin heavily,
(situation like i2c control with gpio emulation)
This situation can cause below problem.
CPU 0 | CPU1
|
samsung_gpio_direction_output |
samsung_gpio_set(pin A as 1) | samsung_gpio_direction_output
| samsung_gpio_set(pin A as 0)
samsung_gpio_set_direction |
| samsung_gpio_set_direction
The initial value of pin A will be set as 0 while we wanted to set pin A as 1.
This patch modifies samsung_gpio_direction_in/output function
to be done in one spinlock to fix race condition.
Additionally, the new samsung_gpio_set_value was added to implement
gpio set callback(samsung_gpio_set) with spinlock using this function.
Cc: [email protected]
Signed-off-by: Youngmin Nam <[email protected]>
Acked-by: Tomasz Figa <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
|
|
In my randconfig tests, I came across a bug that involves several
components:
* gcc-4.9 through at least 5.3
* CONFIG_GCOV_PROFILE_ALL enabling -fprofile-arcs for all files
* CONFIG_PROFILE_ALL_BRANCHES overriding every if()
* The optimized implementation of do_div() that tries to
replace a library call with an division by multiplication
* code in drivers/media/dvb-frontends/zl10353.c doing
u32 adc_clock = 450560; /* 45.056 MHz */
if (state->config.adc_clock)
adc_clock = state->config.adc_clock;
do_div(value, adc_clock);
In this case, gcc fails to determine whether the divisor
in do_div() is __builtin_constant_p(). In particular, it
concludes that __builtin_constant_p(adc_clock) is false, while
__builtin_constant_p(!!adc_clock) is true.
That in turn throws off the logic in do_div() that also uses
__builtin_constant_p(), and instead of picking either the
constant- optimized division, and the code in ilog2() that uses
__builtin_constant_p() to figure out whether it knows the answer at
compile time. The result is a link error from failing to find
multiple symbols that should never have been called based on
the __builtin_constant_p():
dvb-frontends/zl10353.c:138: undefined reference to `____ilog2_NaN'
dvb-frontends/zl10353.c:138: undefined reference to `__aeabi_uldivmod'
ERROR: "____ilog2_NaN" [drivers/media/dvb-frontends/zl10353.ko] undefined!
ERROR: "__aeabi_uldivmod" [drivers/media/dvb-frontends/zl10353.ko] undefined!
This patch avoids the problem by changing __trace_if() to check
whether the condition is known at compile-time to be nonzero, rather
than checking whether it is actually a constant.
I see this one link error in roughly one out of 1600 randconfig builds
on ARM, and the patch fixes all known instances.
Link: http://lkml.kernel.org/r/[email protected]
Acked-by: Nicolas Pitre <[email protected]>
Fixes: ab3c9c686e22 ("branch tracer, intel-iommu: fix build with CONFIG_BRANCH_TRACER=y")
Cc: [email protected] # v2.6.30+
Signed-off-by: Arnd Bergmann <[email protected]>
Signed-off-by: Steven Rostedt <[email protected]>
|
|
The tracepoint infrastructure uses RCU sched protection to enable and
disable tracepoints safely. There are some instances where tracepoints are
used in infrastructure code (like kfree()) that get called after a CPU is
going offline, and perhaps when it is coming back online but hasn't been
registered yet.
This can probuce the following warning:
[ INFO: suspicious RCU usage. ]
4.4.0-00006-g0fe53e8-dirty #34 Tainted: G S
-------------------------------
include/trace/events/kmem.h:141 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
RCU used illegally from offline CPU! rcu_scheduler_active = 1, debug_locks = 1
no locks held by swapper/8/0.
stack backtrace:
CPU: 8 PID: 0 Comm: swapper/8 Tainted: G S 4.4.0-00006-g0fe53e8-dirty #34
Call Trace:
[c0000005b76c78d0] [c0000000008b9540] .dump_stack+0x98/0xd4 (unreliable)
[c0000005b76c7950] [c00000000010c898] .lockdep_rcu_suspicious+0x108/0x170
[c0000005b76c79e0] [c00000000029adc0] .kfree+0x390/0x440
[c0000005b76c7a80] [c000000000055f74] .destroy_context+0x44/0x100
[c0000005b76c7b00] [c0000000000934a0] .__mmdrop+0x60/0x150
[c0000005b76c7b90] [c0000000000e3ff0] .idle_task_exit+0x130/0x140
[c0000005b76c7c20] [c000000000075804] .pseries_mach_cpu_die+0x64/0x310
[c0000005b76c7cd0] [c000000000043e7c] .cpu_die+0x3c/0x60
[c0000005b76c7d40] [c0000000000188d8] .arch_cpu_idle_dead+0x28/0x40
[c0000005b76c7db0] [c000000000101e6c] .cpu_startup_entry+0x50c/0x560
[c0000005b76c7ed0] [c000000000043bd8] .start_secondary+0x328/0x360
[c0000005b76c7f90] [c000000000008a6c] start_secondary_prolog+0x10/0x14
This warning is not a false positive either. RCU is not protecting code that
is being executed while the CPU is offline.
Instead of playing "whack-a-mole(TM)" and adding conditional statements to
the tracepoints we find that are used in this instance, simply add a
cpu_online() test to the tracepoint code where the tracepoint will be
ignored if the CPU is offline.
Use of raw_smp_processor_id() is fine, as there should never be a case where
the tracepoint code goes from running on a CPU that is online and suddenly
gets migrated to a CPU that is offline.
Link: http://lkml.kernel.org/r/[email protected]
Reported-by: Denis Kirjanov <[email protected]>
Fixes: 97e1c18e8d17b ("tracing: Kernel Tracepoints")
Cc: [email protected] # v2.6.28+
Signed-off-by: Steven Rostedt <[email protected]>
|