aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2013-01-19ARM: DMA: Fix struct page iterator in dma_cache_maint() to work with sparsememRussell King1-8/+10
Subhash Jadavani reported this partial backtrace: Now consider this call stack from MMC block driver (this is on the ARMv7 based board): [<c001b50c>] (v7_dma_inv_range+0x30/0x48) from [<c0017b8c>] (dma_cache_maint_page+0x1c4/0x24c) [<c0017b8c>] (dma_cache_maint_page+0x1c4/0x24c) from [<c0017c28>] (___dma_page_cpu_to_dev+0x14/0x1c) [<c0017c28>] (___dma_page_cpu_to_dev+0x14/0x1c) from [<c0017ff8>] (dma_map_sg+0x3c/0x114) This is caused by incrementing the struct page pointer, and running off the end of the sparsemem page array. Fix this by incrementing by pfn instead, and convert the pfn to a struct page. Cc: <[email protected]> Suggested-by: James Bottomley <[email protected]> Tested-by: Subhash Jadavani <[email protected]> Signed-off-by: Russell King <[email protected]>
2013-01-19ACPI, APEI: Fixup incorrect 64-bit access width firmware bugLans Zhang1-0/+3
The bit width check was introduced by 15afae60 (ACPI, APEI: Fix incorrect APEI register bit width check and usage), and a fixup for incorrect 32-bit width memory address was given by f712c71 (ACPI, APEI: Fixup common access width firmware bug). Now there is a similar symptom: [Firmware Bug]: APEI: Invalid bit width + offset in GAR [0x12345000/64/0/3/0] Another bogus BIOS reports an incorrect 64-bit width in trigger table. Thus, apply to a similar workaround for 64-bit width memory address. Signed-off-by: Lans Zhang <[email protected]> Acked-by: Gary Hade <[email protected]> Acked-by: Myron Stowe <[email protected]> Acked-by: Jean Delvare <[email protected]> Signed-off-by: Rafael J. Wysocki <[email protected]>
2013-01-18ARM: OMAP2: Fix missing omap2xxx_clkt_vps_late_init function callsJon Hunter2-0/+4
During the migration to the common clock framework, calls to the functions omap2xxx_clkt_vps_late_init() were not preserved for OMAP2420 and OMAP2430. This causes the variables "sys_ck_rate" and "curr_prcm_set" to be uninitialised on boot. On reboot, this causes the following error message to be displayed because the appropriate MPU clock frequency (derived from sys_ck_rate) cannot be found. "Could not set MPU rate to 4294MHz" Fix this by adding back calls to omap2xxx_clkt_vps_late_init() in the OMAP2420 and OMAP2430 clock initialisation code. Signed-off-by: Jon Hunter <[email protected]> [[email protected]: dropped the duplicated call to omap2xxx_clkt_vps_check_bootloader_rates() after consultation with Jon; updated patch description] Signed-off-by: Paul Walmsley <[email protected]>
2013-01-18ARM: OMAP4: hwmod_data: Correct IDLEMODE for McPDMPeter Ujfalusi1-1/+5
McPDM need to be configured to NO_IDLE mode when it is in used otherwise vital clocks will be gated which results 'slow motion' audio playback. Signed-off-by: Peter Ujfalusi <[email protected]> [[email protected]: copy patch description into hwmod data comments] Signed-off-by: Paul Walmsley <[email protected]>
2013-01-18ARM: OMAP4: clock data: Lock ABE DPLL on all revisionsPeter Ujfalusi1-7/+6
To avoid issues with audio caused by non locked ABE DPLL we should make sure it is locked in all OMAP4 revisions. Signed-off-by: Peter Ujfalusi <[email protected]> Acked-by: Jon Hunter <[email protected]> [[email protected]: cleaned up patch description] Signed-off-by: Paul Walmsley <[email protected]>
2013-01-19ACPI / processor: Get power info before updating the C-statesThomas Schlichter1-0/+1
acpi_processor_get_power_info() has to be called before acpi_processor_setup_cpuidle_states() to have the latest information available. This fixes the missing C-state information after AC-->DC transition. Signed-off-by: Thomas Schlichter <[email protected]> Cc: <[email protected]> Signed-off-by: Rafael J. Wysocki <[email protected]>
2013-01-18Merge tag 'usb-3.8-rc4' of ↵Linus Torvalds2-1/+11
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb Pull USB fixes from Greg Kroah-Hartman: "Here are 3 USB patches for 3.8-rc4. Two of them are new device id patches, and the third fixes a reported oops in the io_ti USB serial driver" * tag 'usb-3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: USB: io_ti: Fix NULL dereference in chase_port() USB: option: add TP-LINK HSUPA Modem MA180 USB: option: blacklist network interface on ONDA MT8205 4G LTE
2013-01-18Merge tag 'tty-3.8-rc4' of ↵Linus Torvalds10-9/+65
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty Pull tty/serial fixes from Greg Kroah-Hartman: "Here are a few tty/serial driver fixes for 3.8-rc4 that resolve a number of problems that people have been having, including the ptys ioctl issue that is a regression fix" * tag 'tty-3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: 8250/16?50: Add support for Broadcom TruManage redirected serial port pty: return EINVAL for TIOCGPTN for BSD ptys serial:ifx6x60:Keep word size accordance with SPI controller tty: 8250_dw: Fix inverted arguments to serial_out in IRQ handler serial: samsung: remove redundant setting of line config during port reset serial:ifx6x60:Delete SPI timer when shut down port tty/8250: The correct device id for this card is 0x0022 tty/8250: pbn_b0_8_1152000_200 is supposed to be an 8 port definition tty: serial: vt8500: fix return value check in vt8500_serial_probe() serial: mxs-auart: Index is unsigned mxs: uart: fix setting RTS from software
2013-01-18Merge tag 'staging-3.8-rc4' of ↵Linus Torvalds8-28/+23
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging Pull staging driver bugfixes from Greg Kroah-Hartman: "Here are some bugfixes for the drivers/staging tree for 3.8-rc4. Nothing major, just a number of small fixes for problems that people have reported, including finally tracking down the root of the 64/32 bit problem with the vt6656 that has been driving people crazy for a while" * tag 'staging-3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: staging/sb105x: PARPORT config is not good enough must use PARPORT_PC staging: wlan-ng: Fix clamping of returned SSID length staging: vt6656: Fix inconsistent structure packing staging:iio:adis16080: Perform sign extension iio: mxs-lradc: indexes are unsigned
2013-01-18Merge tag 'char-misc-3.8-rc4' of ↵Linus Torvalds1-14/+21
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc Pull char/misc driver fixes from Greg Kroah-Hartman: "Here are two hyperv patches for 3.8-rc4 that fix some reported problems hv_balloon driver" * tag 'char-misc-3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: Drivers: hv: balloon: Fix a memory leak Drivers: hv: balloon: Fix a bug in the definition of struct dm_info_msg
2013-01-18Merge tag 'stable/for-linus-3.8-rc3-tag' of ↵Linus Torvalds7-114/+167
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen Pull Xen fixes from Konrad Rzeszutek Wilk: - CVE-2013-0190/XSA-40 (or stack corruption for 32-bit PV kernels) - Fix racy vma access spotted by Al Viro - Fix mmap batch ioctl potentially resulting in large O(n) page allcations. - Fix vcpu online/offline BUG:scheduling while atomic.. - Fix unbound buffer scanning for more than 32 vCPUs. - Fix grant table being incorrectly initialized - Fix incorrect check in pciback - Allow privcmd in backend domains. Fix up whitespace conflict due to ugly merge resolution in Xen tree in arch/arm/xen/enlighten.c * tag 'stable/for-linus-3.8-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen: xen: Fix stack corruption in xen_failsafe_callback for 32bit PVOPS guests. Revert "xen/smp: Fix CPU online/offline bug triggering a BUG: scheduling while atomic." xen/gntdev: remove erronous use of copy_to_user xen/gntdev: correctly unmap unlinked maps in mmu notifier xen/gntdev: fix unsafe vma access xen/privcmd: Fix mmap batch ioctl. Xen: properly bound buffer access when parsing cpu/*/availability xen/grant-table: correctly initialize grant table version 1 x86/xen : Fix the wrong check in pciback xen/privcmd: Relax access control in privcmd_ioctl_mmap
2013-01-18Merge branch 'for-linus' of ↵Linus Torvalds2-3/+7
git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu Pull m68knommu arch fixes from Greg Ungerer: "This contains a couple of fixes, both affecting compilation of non-mmu m68k targets." * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu: m68k: fix conditional use of init_pointer_table m68knommu: add KMAP definitions for non-MMU definitions
2013-01-18net/mlx4_core: Set number of msix vectors under SRIOV mode to firmware defaultsOr Gerlitz1-9/+2
The lines if (mlx4_is_mfunc(dev)) { nreq = 2; } else { which hard code the number of requested msi-x vectors under multi-function mode to two can be removed completely, since the firmware sets num_eqs and reserved_eqs appropriately Thus, the code line: nreq = min_t(int, dev->caps.num_eqs - dev->caps.reserved_eqs, nreq); is by itself sufficient and correct for all cases. Currently, for mfunc mode num_eqs = 32 and reserved_eqs = 28, hence four vectors will be enabled. This triples (one vector is used for the async events and commands EQ) the horse power provided for processing of incoming packets on netdev RSS scheme, IO initiators/targets commands processing flows, etc. Reviewed-by: Jack Morgenstein <[email protected]> Signed-off-by: Amir Vadai <[email protected]> Signed-off-by: Or Gerlitz <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2013-01-18net/mlx4_en: Fix bridged vSwitch configuration for non SRIOV modeYan Burman1-4/+9
Commit 5b4c4d36860e "mlx4_en: Allow communication between functions on same host" introduced a regression under which a bridge acting as vSwitch whose uplink is an mlx4 Ethernet device become non-operative in native (non sriov) mode. This happens since broadcast ARP requests sent by VMs were loopback-ed by the HW and hence the bridge learned VM source MACs on both the VM and the uplink ports. The fix is to place the DMAC in the send WQE only under SRIOV/eSwitch configuration or when the device is in selftest. Reviewed-by: Or Gerlitz <[email protected]> Signed-off-by: Yan Burman <[email protected]> Signed-off-by: Amir Vadai <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2013-01-18asm-generic, mm: pgtable: convert my_zero_pfn() to macros to fix buildKirill A. Shutemov1-4/+2
Commit 816422ad7647 ("asm-generic, mm: pgtable: consolidate zero page helpers") broke the compile on MIPS if SPARSEMEM is enabled. We get this: In file included from arch/mips/include/asm/pgtable.h:552, from include/linux/mm.h:44, from arch/mips/kernel/asm-offsets.c:14: include/asm-generic/pgtable.h: In function 'my_zero_pfn': include/asm-generic/pgtable.h:466: error: implicit declaration of function 'page_to_section' In file included from arch/mips/kernel/asm-offsets.c:14: include/linux/mm.h: At top level: include/linux/mm.h:738: error: conflicting types for 'page_to_section' include/asm-generic/pgtable.h:466: note: previous implicit declaration of 'page_to_section' was here Due header files inter-dependencies, the only way I see to fix it is convert my_zero_pfn() for __HAVE_COLOR_ZERO_PAGE to macros. Signed-off-by: Kirill A. Shutemov <[email protected]> Tested-by: Aaro Koskinen <[email protected]> Acked-by: David Daney <[email protected]> Cc: Andrew Morton <[email protected]> Signed-off-by: Linus Torvalds <[email protected]>
2013-01-18ipv6: Add an error handler for icmp6Steffen Klassert1-0/+12
pmtu and redirect events are now handled in the protocols error handler, so add an error handler for icmp6 to do this. It is needed in the case when we have no socket context. Based on a patch by Duan Jiong. Reported-by: Duan Jiong <[email protected]> Signed-off-by: Steffen Klassert <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2013-01-18net: calxedaxgmac: throw away overrun framesRob Herring1-0/+4
The xgmac driver assumes 1 frame per descriptor. If a frame larger than the descriptor's buffer size is received, the frame will spill over into the next descriptor. So check for received frames that span more than one descriptor and discard them. This prevents a crash if we receive erroneous large packets. Signed-off-by: Rob Herring <[email protected]> Cc: [email protected] Cc: [email protected] Signed-off-by: David S. Miller <[email protected]>
2013-01-18powernow-k8: Add a kconfig dependency on acpi-cpufreqBorislav Petkov1-1/+1
Andreas reports in https://bugzilla.kernel.org/show_bug.cgi?id=51741 that with his Gentoo config, acpi-cpufreq wasn't enabled and powernow-k8 couldn't handoff properly to acpi-cpufreq leading to running without P-state support (i.e., cores are constantly in P0). To alleaviate that, we need to make powernow-k8 depend on acpi-cpufreq so that acpi-cpufreq is always present. References: https://bugzilla.kernel.org/show_bug.cgi?id=51741 Reported-by: Andreas <[email protected]> Signed-off-by: Borislav Petkov <[email protected]> Cc: 3.7+ <[email protected]> Signed-off-by: Rafael J. Wysocki <[email protected]>
2013-01-18ACPI / cpuidle: Fix NULL pointer issues when cpuidle is disabledKonrad Rzeszutek Wilk1-0/+3
If cpuidle is disabled, that means that: per_cpu(acpi_cpuidle_device, pr->id) is set to NULL as the acpi_processor_power_init ends up failing at retval = cpuidle_register_driver(&acpi_idle_driver) (in acpi_processor_power_init) and never sets the per_cpu idle device. So when acpi_processor_hotplug on CPU online notification tries to reference said device it crashes: cpu 3 spinlock event irq 62 BUG: unable to handle kernel NULL pointer dereference at 0000000000000004 IP: [<ffffffff81381013>] acpi_processor_setup_cpuidle_cx+0x3f/0x105 PGD a259b067 PUD ab38b067 PMD 0 Oops: 0002 [#1] SMP odules linked in: dm_multipath dm_mod xen_evtchn iscsi_boot_sysfs iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi libcrc32c crc32c nouveau mxm_wmi wmi radeon ttm sg sr_mod sd_mod cdrom ata_generic ata_piix libata crc32c_intel scsi_mod atl1c i915 fbcon tileblit font bitblit softcursor drm_kms_helper video xen_blkfront xen_netfront fb_sys_fops sysimgblt sysfillrect syscopyarea xenfs xen_privcmd mperf CPU 1 Pid: 3047, comm: bash Not tainted 3.8.0-rc3upstream-00250-g165c029 #1 MSI MS-7680/H61M-P23 (MS-7680) RIP: e030:[<ffffffff81381013>] [<ffffffff81381013>] acpi_processor_setup_cpuidle_cx+0x3f/0x105 RSP: e02b:ffff88001742dca8 EFLAGS: 00010202 RAX: 0000000000010be9 RBX: ffff8800a0a61800 RCX: ffff880105380000 RDX: 0000000000000003 RSI: 0000000000000200 RDI: ffff8800a0a61800 RBP: ffff88001742dce8 R08: ffffffff81812360 R09: 0000000000000200 R10: aaaaaaaaaaaaaaaa R11: 0000000000000001 R12: ffff8800a0a61800 R13: 00000000ffffff01 R14: 0000000000000000 R15: ffffffff81a907a0 FS: 00007fd6942f7700(0000) GS:ffff880105280000(0000) knlGS:0000000000000000 CS: e033 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000004 CR3: 00000000a6773000 CR4: 0000000000042660 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Process bash (pid: 3047, threadinfo ffff88001742c000, task ffff880017944000) Stack: 0000000000000150 ffff880100f59e00 ffff88001742dcd8 ffff8800a0a61800 0000000000000000 00000000ffffff01 0000000000000000 ffffffff81a907a0 ffff88001742dd18 ffffffff813815b1 ffff88001742dd08 ffffffff810ae336 Call Trace: [<ffffffff813815b1>] acpi_processor_hotplug+0x7c/0x9f [<ffffffff810ae336>] ? schedule_delayed_work_on+0x16/0x20 [<ffffffff8137ee8f>] acpi_cpu_soft_notify+0x90/0xca [<ffffffff8166023d>] notifier_call_chain+0x4d/0x70 [<ffffffff810bc369>] __raw_notifier_call_chain+0x9/0x10 [<ffffffff81094a4b>] __cpu_notify+0x1b/0x30 [<ffffffff81652cf7>] _cpu_up+0x103/0x14b [<ffffffff81652e18>] cpu_up+0xd9/0xec [<ffffffff8164a254>] store_online+0x94/0xd0 [<ffffffff814122fb>] dev_attr_store+0x1b/0x20 [<ffffffff81216404>] sysfs_write_file+0xf4/0x170 This patch fixes it. Signed-off-by: Konrad Rzeszutek Wilk <[email protected]> Cc: <[email protected]> Signed-off-by: Rafael J. Wysocki <[email protected]>
2013-01-18intel_idle: Don't register CPU notifier if we are not running.Konrad Rzeszutek Wilk1-2/+1
The 'intel_idle_probe' probes the CPU and sets the CPU notifier. But if later on during the module initialization we fail (say in cpuidle_register_driver), we stop loading, but we neglect to unregister the CPU notifier. This means that during CPU hotplug events the system will fail: calling intel_idle_init+0x0/0x326 @ 1 intel_idle: MWAIT substates: 0x1120 intel_idle: v0.4 model 0x2A intel_idle: lapic_timer_reliable_states 0xffffffff intel_idle: intel_idle yielding to none initcall intel_idle_init+0x0/0x326 returned -19 after 14 usecs ... some time later, offlining and onlining a CPU: cpu 3 spinlock event irq 62 BUG: unable to ] __cpuidle_register_device+0x1c/0x120 PGD 99b8b067 PUD 99b95067 PMD 0 Oops: 0000 [#1] SMP Modules linked in: xen_evtchn nouveau mxm_wmi wmi radeon ttm i915 fbcon tileblit font atl1c bitblit softcursor drm_kms_helper video xen_blkfront xen_netfront fb_sys_fops sysimgblt sysfillrect syscopyarea xenfs xen_privcmd mperf CPU 0 Pid: 2302, comm: udevd Not tainted 3.8.0-rc3upstream-00249-g09ad159 #1 MSI MS-7680/H61M-P23 (MS-7680) RIP: e030:[<ffffffff814d956c>] [<ffffffff814d956c>] __cpuidle_register_device+0x1c/0x120 RSP: e02b:ffff88009dacfcb8 EFLAGS: 00010286 RAX: 0000000000000000 RBX: ffff880105380000 RCX: 000000000000001c RDX: 0000000000000000 RSI: 0000000000000055 RDI: ffff880105380000 RBP: ffff88009dacfce8 R08: ffffffff81a4f048 R09: 0000000000000008 R10: 0000000000000008 R11: 0000000000000000 R12: ffff880105380000 R13: 00000000ffffffdd R14: 0000000000000000 R15: ffffffff81a523d0 FS: 00007f37bd83b7a0(0000) GS:ffff880105200000(0000) knlGS:0000000000000000 CS: e033 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000008 CR3: 00000000a09ea000 CR4: 0000000000042660 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Process udevd (pid: 2302, threadinfo ffff88009dace000, task ffff88009afb47f0) Stack: ffffffff8107f2d0 ffffffff810c2fb7 ffff88009dacfce8 00000000ffffffea ffff880105380000 00000000ffffffdd ffff88009dacfd08 ffffffff814d9882 0000000000000003 ffff880105380000 ffff88009dacfd28 ffffffff81340afd Call Trace: [<ffffffff8107f2d0>] ? collect_cpu_info_local+0x30/0x30 [<ffffffff810c2fb7>] ? __might_sleep+0xe7/0x100 [<ffffffff814d9882>] cpuidle_register_device+0x32/0x70 [<ffffffff81340afd>] intel_idle_cpu_init+0xad/0x110 [<ffffffff81340bc8>] cpu_hotplug_notify+0x68/0x80 [<ffffffff8166023d>] notifier_call_chain+0x4d/0x70 [<ffffffff810bc369>] __raw_notifier_call_chain+0x9/0x10 [<ffffffff81094a4b>] __cpu_notify+0x1b/0x30 [<ffffffff81652cf7>] _cpu_up+0x103/0x14b [<ffffffff81652e18>] cpu_up+0xd9/0xec [<ffffffff8164a254>] store_online+0x94/0xd0 [<ffffffff814122fb>] dev_attr_store+0x1b/0x20 [<ffffffff81216404>] sysfs_write_file+0xf4/0x170 [<ffffffff811a1024>] vfs_write+0xb4/0x130 [<ffffffff811a17ea>] sys_write+0x5a/0xa0 [<ffffffff816643a9>] system_call_fastpath+0x16/0x1b Code: 03 18 00 c9 c3 66 2e 0f 1f 84 00 00 00 00 00 55 48 89 e5 48 83 ec 30 48 89 5d e8 4c 89 65 f0 48 89 fb 4c 89 6d f8 e8 84 08 00 00 <48> 8b 78 08 49 89 c4 e8 f8 7f c1 ff 89 c2 b8 ea ff ff ff 84 d2 RIP [<ffffffff814d956c>] __cpuidle_register_device+0x1c/0x120 RSP <ffff88009dacfcb8> This patch fixes that by moving the CPU notifier registration as the last item to be done by the module. Signed-off-by: Konrad Rzeszutek Wilk <[email protected]> Reviewed-by: Srivatsa S. Bhat <[email protected]> Cc: 3.6+ <[email protected]> Signed-off-by: Rafael J. Wysocki <[email protected]>
2013-01-18usb: gadget: FunctionFS: Fix missing braces in parse_optsBenoit Goby1-3/+3
Add missing braces around an if block in ffs_fs_parse_opts. This broke parsing the uid/gid mount options and causes mount to fail when using uid/gid. This has been introduced by commit b9b73f7c (userns: Convert usb functionfs to use kuid/kgid where appropriate) in 3.7. Cc: <[email protected]> Signed-off-by: Benoit Goby <[email protected]> Acked-by: Michal Nazarewicz <[email protected]> Signed-off-by: Felipe Balbi <[email protected]>
2013-01-18usb: dwc3: gadget: fix ep->maxburst for ep0Pratyush Anand1-0/+1
dwc3_gadget_set_ep_config expects maxburst as incremented by 1. So, by default initialize ep->maxburst to 1 for ep0. Cc: <[email protected]> Signed-off-by: Pratyush Anand <[email protected]> Signed-off-by: Felipe Balbi <[email protected]>
2013-01-18ARM: i.MX clock: Change the connection-id for fsl-usb2-udcPeter Chen5-15/+15
As we use platform_device_id for fsl-usb2-udc driver, it needs to change clk connection-id, or the related devm_clk_get will be failed. Signed-off-by: Peter Chen <[email protected]> Acked-by: Shawn Guo <[email protected]> Signed-off-by: Felipe Balbi <[email protected]>
2013-01-18usb: gadget: fsl_mxc_udc: replace MX35_IO_ADDRESS to ioremapPeter Chen3-10/+29
As mach/hardware.h is deleted, we can't visit platform code at driver. It has no phy driver to combine with this controller, so it has to use ioremap to map phy address as a workaround. Signed-off-by: Peter Chen <[email protected]> Signed-off-by: Felipe Balbi <[email protected]>
2013-01-18usb: gadget: fsl-mxc-udc: replace cpu_is_xxx() with platform_device_idPeter Chen4-37/+41
As mach/hardware.h is deleted, we need to use platform_device_id to differentiate SoCs. Besides, one cpu_is_mx35 is useless as it has already used pdata to differentiate runtime Meanwhile we update the platform code accordingly. Signed-off-by: Peter Chen <[email protected]> Signed-off-by: Felipe Balbi <[email protected]>
2013-01-18usb: musb: cppi_dma: drop '__init' annotationSergei Shtylyov1-2/+2
This patch fixes the following: WARNING: vmlinux.o(.text+0x1e709c): Section mismatch in reference from the funct ion dma_controller_create() to the function .init.text:cppi_controller_start() The function dma_controller_create() references the function __init cppi_controller_start(). This is often because dma_controller_create lacks a __init annotation or the annotation of cppi_controller_start is wrong. This warning is there due to the deficiency in the commit 07a67bbb (usb: musb: Make dma_controller_create __devinit). Since the start() method is only called from musb_init_controller() which is not annotated, drop '__init' annotation from cppi_controller_start() and also cppi_pool_init() since it gets called from that function, to avoid another section mismatch warning... Signed-off-by: Sergei Shtylyov <[email protected]> Cc: [email protected] # 3.7+ Signed-off-by: Felipe Balbi <[email protected]>
2013-01-18ALSA: hda - Fix mute led for another HP machineDavid Henningsson1-0/+1
This machine also has the "HP_Mute_LED_0_A" string in DMI information. Cc: <[email protected]> BugLink: https://bugs.launchpad.net/bugs/1096789 Tested-by: Tammy Yang <[email protected]> Signed-off-by: David Henningsson <[email protected]> Signed-off-by: Takashi Iwai <[email protected]>
2013-01-18net/xfrm/xfrm_replay: avoid division by zeroNickolai Zeldovich1-1/+3
All of the xfrm_replay->advance functions in xfrm_replay.c check if x->replay_esn->replay_window is zero (and return if so). However, one of them, xfrm_replay_advance_bmp(), divides by that value (in the '%' operator) before doing the check, which can potentially trigger a divide-by-zero exception. Some compilers will also assume that the earlier division means the value cannot be zero later, and thus will eliminate the subsequent zero check as dead code. This patch moves the division to after the check. Signed-off-by: Nickolai Zeldovich <[email protected]> Signed-off-by: Steffen Klassert <[email protected]>
2013-01-17Linux 3.8-rc4Linus Torvalds1-1/+1
2013-01-17USB: io_ti: Fix NULL dereference in chase_port()Wolfgang Frisch1-0/+3
The tty is NULL when the port is hanging up. chase_port() needs to check for this. This patch is intended for stable series. The behavior was observed and tested in Linux 3.2 and 3.7.1. Johan Hovold submitted a more elaborate patch for the mainline kernel. [ 56.277883] usb 1-1: edge_bulk_in_callback - nonzero read bulk status received: -84 [ 56.278811] usb 1-1: USB disconnect, device number 3 [ 56.278856] usb 1-1: edge_bulk_in_callback - stopping read! [ 56.279562] BUG: unable to handle kernel NULL pointer dereference at 00000000000001c8 [ 56.280536] IP: [<ffffffff8144e62a>] _raw_spin_lock_irqsave+0x19/0x35 [ 56.281212] PGD 1dc1b067 PUD 1e0f7067 PMD 0 [ 56.282085] Oops: 0002 [#1] SMP [ 56.282744] Modules linked in: [ 56.283512] CPU 1 [ 56.283512] Pid: 25, comm: khubd Not tainted 3.7.1 #1 innotek GmbH VirtualBox/VirtualBox [ 56.283512] RIP: 0010:[<ffffffff8144e62a>] [<ffffffff8144e62a>] _raw_spin_lock_irqsave+0x19/0x35 [ 56.283512] RSP: 0018:ffff88001fa99ab0 EFLAGS: 00010046 [ 56.283512] RAX: 0000000000000046 RBX: 00000000000001c8 RCX: 0000000000640064 [ 56.283512] RDX: 0000000000010000 RSI: ffff88001fa99b20 RDI: 00000000000001c8 [ 56.283512] RBP: ffff88001fa99b20 R08: 0000000000000000 R09: 0000000000000000 [ 56.283512] R10: 0000000000000000 R11: ffffffff812fcb4c R12: ffff88001ddf53c0 [ 56.283512] R13: 0000000000000000 R14: 00000000000001c8 R15: ffff88001e19b9f4 [ 56.283512] FS: 0000000000000000(0000) GS:ffff88001fd00000(0000) knlGS:0000000000000000 [ 56.283512] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b [ 56.283512] CR2: 00000000000001c8 CR3: 000000001dc51000 CR4: 00000000000006e0 [ 56.283512] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 56.283512] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 [ 56.283512] Process khubd (pid: 25, threadinfo ffff88001fa98000, task ffff88001fa94f80) [ 56.283512] Stack: [ 56.283512] 0000000000000046 00000000000001c8 ffffffff810578ec ffffffff812fcb4c [ 56.283512] ffff88001e19b980 0000000000002710 ffffffff812ffe81 0000000000000001 [ 56.283512] ffff88001fa94f80 0000000000000202 ffffffff00000001 0000000000000296 [ 56.283512] Call Trace: [ 56.283512] [<ffffffff810578ec>] ? add_wait_queue+0x12/0x3c [ 56.283512] [<ffffffff812fcb4c>] ? usb_serial_port_work+0x28/0x28 [ 56.283512] [<ffffffff812ffe81>] ? chase_port+0x84/0x2d6 [ 56.283512] [<ffffffff81063f27>] ? try_to_wake_up+0x199/0x199 [ 56.283512] [<ffffffff81263a5c>] ? tty_ldisc_hangup+0x222/0x298 [ 56.283512] [<ffffffff81300171>] ? edge_close+0x64/0x129 [ 56.283512] [<ffffffff810612f7>] ? __wake_up+0x35/0x46 [ 56.283512] [<ffffffff8106135b>] ? should_resched+0x5/0x23 [ 56.283512] [<ffffffff81264916>] ? tty_port_shutdown+0x39/0x44 [ 56.283512] [<ffffffff812fcb4c>] ? usb_serial_port_work+0x28/0x28 [ 56.283512] [<ffffffff8125d38c>] ? __tty_hangup+0x307/0x351 [ 56.283512] [<ffffffff812e6ddc>] ? usb_hcd_flush_endpoint+0xde/0xed [ 56.283512] [<ffffffff8144e625>] ? _raw_spin_lock_irqsave+0x14/0x35 [ 56.283512] [<ffffffff812fd361>] ? usb_serial_disconnect+0x57/0xc2 [ 56.283512] [<ffffffff812ea99b>] ? usb_unbind_interface+0x5c/0x131 [ 56.283512] [<ffffffff8128d738>] ? __device_release_driver+0x7f/0xd5 [ 56.283512] [<ffffffff8128d9cd>] ? device_release_driver+0x1a/0x25 [ 56.283512] [<ffffffff8128d393>] ? bus_remove_device+0xd2/0xe7 [ 56.283512] [<ffffffff8128b7a3>] ? device_del+0x119/0x167 [ 56.283512] [<ffffffff812e8d9d>] ? usb_disable_device+0x6a/0x180 [ 56.283512] [<ffffffff812e2ae0>] ? usb_disconnect+0x81/0xe6 [ 56.283512] [<ffffffff812e4435>] ? hub_thread+0x577/0xe82 [ 56.283512] [<ffffffff8144daa7>] ? __schedule+0x490/0x4be [ 56.283512] [<ffffffff8105798f>] ? abort_exclusive_wait+0x79/0x79 [ 56.283512] [<ffffffff812e3ebe>] ? usb_remote_wakeup+0x2f/0x2f [ 56.283512] [<ffffffff812e3ebe>] ? usb_remote_wakeup+0x2f/0x2f [ 56.283512] [<ffffffff810570b4>] ? kthread+0x81/0x89 [ 56.283512] [<ffffffff81057033>] ? __kthread_parkme+0x5c/0x5c [ 56.283512] [<ffffffff8145387c>] ? ret_from_fork+0x7c/0xb0 [ 56.283512] [<ffffffff81057033>] ? __kthread_parkme+0x5c/0x5c [ 56.283512] Code: 8b 7c 24 08 e8 17 0b c3 ff 48 8b 04 24 48 83 c4 10 c3 53 48 89 fb 41 50 e8 e0 0a c3 ff 48 89 04 24 e8 e7 0a c3 ff ba 00 00 01 00 <f0> 0f c1 13 48 8b 04 24 89 d1 c1 ea 10 66 39 d1 74 07 f3 90 66 [ 56.283512] RIP [<ffffffff8144e62a>] _raw_spin_lock_irqsave+0x19/0x35 [ 56.283512] RSP <ffff88001fa99ab0> [ 56.283512] CR2: 00000000000001c8 [ 56.283512] ---[ end trace 49714df27e1679ce ]--- Signed-off-by: Wolfgang Frisch <[email protected]> Cc: Johan Hovold <[email protected]> Cc: stable <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2013-01-17USB: option: add TP-LINK HSUPA Modem MA180Bjørn Mork1-0/+6
The driver description files gives these names to the vendor specific functions on this modem: Diagnostics VID_2357&PID_0201&MI_00 NMEA VID_2357&PID_0201&MI_01 Modem VID_2357&PID_0201&MI_03 Networkcard VID_2357&PID_0201&MI_04 Reported-by: Thomas Schäfer <[email protected]> Signed-off-by: Bjørn Mork <[email protected]> Cc: stable <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2013-01-17USB: option: blacklist network interface on ONDA MT8205 4G LTEBjørn Mork1-1/+2
The driver description files gives these names to the vendor specific functions on this modem: Diag VID_19D2&PID_0265&MI_00 NMEA VID_19D2&PID_0265&MI_01 AT cmd VID_19D2&PID_0265&MI_02 Modem VID_19D2&PID_0265&MI_03 Net VID_19D2&PID_0265&MI_04 Signed-off-by: Bjørn Mork <[email protected]> Cc: stable <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2013-01-17staging/sb105x: PARPORT config is not good enough must use PARPORT_PCSteven Rostedt1-1/+1
The sb105x driver calls parport_pc_probe_port() which isn't defined if PARPORT_PC isn't enabled. Protecting it with CONFIG_PARPORT is not good enough, must protect it with CONFIG_PARPORT_PC. Reported-by: Randy Dunlap <[email protected]> Acked-by: Randy Dunlap <[email protected]> Signed-off-by: Steven Rostedt <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2013-01-17staging: wlan-ng: Fix clamping of returned SSID lengthTormod Volden1-1/+1
Commit 2e254212 broke listing of available network names, since it clamped the length of the returned SSID to WLAN_BSSID_LEN (6) instead of WLAN_SSID_MAXLEN (32). https://bugzilla.kernel.org/show_bug.cgi?id=52501 Signed-off-by: Tormod Volden <[email protected]> Cc: stable <[email protected]> # 3.4+ Signed-off-by: Greg Kroah-Hartman <[email protected]>
2013-01-17Merge tag 'iio-fixes-for-3.8b' of ↵Greg Kroah-Hartman2-2/+2
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus Jonathan writes: Second round of fixes for IIO post 3.8-rc1 Two tiny fixes * A build warning fix due to signed / unsigned comparison * Missing sign extension in adis16080
2013-01-18KVM: PPC: Emulate dcbfAlexander Graf1-0/+2
Guests can trigger MMIO exits using dcbf. Since we don't emulate cache incoherent MMIO, just do nothing and move on. Reported-by: Ben Collins <[email protected]> Signed-off-by: Alexander Graf <[email protected]> Tested-by: Ben Collins <[email protected]> CC: [email protected]
2013-01-17sctp: refactor sctp_outq_teardown to insure proper re-initalizationNeil Horman1-4/+8
Jamie Parsons reported a problem recently, in which the re-initalization of an association (The duplicate init case), resulted in a loss of receive window space. He tracked down the root cause to sctp_outq_teardown, which discarded all the data on an outq during a re-initalization of the corresponding association, but never reset the outq->outstanding_data field to zero. I wrote, and he tested this fix, which does a proper full re-initalization of the outq, fixing this problem, and hopefully future proofing us from simmilar issues down the road. Signed-off-by: Neil Horman <[email protected]> Reported-by: Jamie Parsons <[email protected]> Tested-by: Jamie Parsons <[email protected]> CC: Jamie Parsons <[email protected]> CC: Vlad Yasevich <[email protected]> CC: "David S. Miller" <[email protected]> CC: [email protected] Acked-by: Vlad Yasevich <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2013-01-17PCI: remove depends on CONFIG_EXPERIMENTALKees Cook1-1/+1
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a while now and is almost always enabled by default. As agreed during the Linux kernel summit, remove it from any "depends on" lines in Kconfigs. Signed-off-by: Kees Cook <[email protected]> Signed-off-by: Bjorn Helgaas <[email protected]>
2013-01-178250/16?50: Add support for Broadcom TruManage redirected serial portStephen Hurd4-1/+52
Add support for the UART device present in Broadcom TruManage capable NetXtreme chips (ie: 5761m 5762, and 5725). This implementation has a hidden transmit FIFO, so running in single-byte interrupt mode results in too many interrupts. The UART_CAP_HFIFO capability was added to track this. It continues to reload the THR as long as the THRE and TSRE bits are set in the LSR up to a specified limit (1024 is used here). Signed-off-by: Stephen Hurd <[email protected]> Signed-off-by: Michael Chan <[email protected]> Cc: stable <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2013-01-17pty: return EINVAL for TIOCGPTN for BSD ptysJiri Slaby1-0/+2
Commit bbb63c514a3464342967237a51a21ea8f61ab951 (drivers:tty:fix up ENOIOCTLCMD error handling) changed the default return value from tty ioctl to be ENOTTY and not EINVAL. This is appropriate. But in case of TIOCGPTN for the old BSD ptys glibc started failing because it expects EINVAL to be returned. Only then it continues to obtain the pts name the other way around. So fix this case by explicit return of EINVAL in this case. Signed-off-by: Jiri Slaby <[email protected]> Reported-by: Florian Westphal <[email protected]> Cc: Alan Cox <[email protected]> Cc: stable <[email protected]> # 3.7+ Signed-off-by: Greg Kroah-Hartman <[email protected]>
2013-01-17macvlan: fix macvlan_get_size()Eric Dumazet1-1/+4
commit df8ef8f3aaa (macvlan: add FDB bridge ops and macvlan flags) forgot to update macvlan_get_size() after the addition of IFLA_MACVLAN_FLAGS Signed-off-by: Eric Dumazet <[email protected]> Cc: John Fastabend <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2013-01-17staging: vt6656: Fix inconsistent structure packingBen Hutchings4-24/+19
vt6656 has several headers that use the #pragma pack(1) directive to enable structure packing, but never disable it. The layout of structures defined in other headers can then depend on which order the various headers are included in, breaking the One Definition Rule. In practice this resulted in crashes on x86_64 until the order of header inclusion was changed for some files in commit 11d404cb56ecd ('staging: vt6656: fix headers and add cfg80211.'). But we need a proper fix that won't be affected by future changes to the order of inclusion. This removes the #pragma pack(1) directives and adds __packed to the structure definitions for which packing appears to have been intended. Reported-and-tested-by: Malcolm Priestley <[email protected]> Signed-off-by: Ben Hutchings <[email protected]> Cc: [email protected] Signed-off-by: Greg Kroah-Hartman <[email protected]>
2013-01-17phy/marvell: remove fiber/copper autoselect on 88e1111Stef van Os1-9/+0
Remove the code that always enables copper/fiber autoselect, ignoring the DIS_FC strapping pin. The default value for this register is autoselect on anyway, and if you explicitly disable autoselect via strapping you probably really don't want autoselect. Signed-off-by: Stef van Os <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2013-01-173c574_cs: fix operator precedence between << and &Nickolai Zeldovich1-1/+1
The code to print the FIFO size in tc574_config computes it as: 8 << config & Ram_size which evaluates the '<<' first, but the actual intent is to evaluate the '&' first. Add parentheses to enforce desired evaluation order. Signed-off-by: Nickolai Zeldovich <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2013-01-17Drivers: hv: balloon: Fix a memory leakK. Y. Srinivasan1-10/+13
The send buffer was being leaked; fix it. Signed-off-by: K. Y. Srinivasan <[email protected]> Reviewed-by: Haiyang Zhang <[email protected]> Reported-by: Jason Wang <[email protected]> Acked-by: Jason Wang <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2013-01-17Drivers: hv: balloon: Fix a bug in the definition of struct dm_info_msgK. Y. Srinivasan1-4/+8
There is bug in the definition of struct dm_info_msg. This patch fixes the definition of this structure and makes the corresponding adjustments. Signed-off-by: K. Y. Srinivasan <[email protected]> Reviewed-by: Haiyang Zhang <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>
2013-01-17Merge branch 'wireless'David S. Miller17-88/+73
John W. Linville says: ==================== This batch of fixes is intended for 3.8... Included is a Bluetooth pull. Gustavo says: "A few fixes for 3.8. Five of them are just new devices ids addition. Apart from the that there is fix to a kernel memory leak to userspace from Anderson Lizardo, two interoperability fixes from Jaganath Kanakkassery and Szymon Janc. And a crash fix by me." Along with that, Amitkumar Karwar brings a pair of mwifiex fixes for problems related to handling of band information within the driver. These problems can lead to association failures. Sujith Manoharan fixes a memory leak in the ath9k_htc code (originally reported by Larry Finger). The big hero this round is Felix Fietkau. Felix gives us seven ath9k fixes, including a fix for a race condition, the removal of a double-free, and a fix for a deadlock, among others. These have all been in linux-next for at least a couple of days, with no complaints so far. Please let me know if there are problems! ==================== Signed-off-by: David S. Miller <[email protected]>
2013-01-17Revert "drm/radeon: do not move bo to different placement at each cs"Alex Deucher2-9/+10
This reverts commit d025e9e2b890db679f1246037bf65bd4be512627. This causes corruption for a number of users and needs further investigation in the next cycle. https://bugzilla.kernel.org/show_bug.cgi?id=52491 https://bugs.freedesktop.org/show_bug.cgi?id=58659 http://lists.freedesktop.org/archives/dri-devel/2013-January/032961.html Signed-off-by: Alex Deucher <[email protected]>
2013-01-17Merge branch 'master' of ↵John W. Linville17-88/+73
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
2013-01-17Merge branch 'for-linus' of ↵Linus Torvalds6-27/+45
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux Pull more s390 patches from Martin Schwidefsky: "A couple of bug fixes: one of the transparent huge page primitives is broken, the sched_clock function overflows after 417 days, the XFS module has grown too large for -fpic and the new pci code has broken normal channel subsystem notifications." * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: s390/chsc: fix SEI usage s390/time: fix sched_clock() overflow s390: use -fPIC for module compile s390/mm: fix pmd_pfn() for thp
Powered by cgit, Gruvboxed by Blaster4385.