Age | Commit message (Collapse) | Author | Files | Lines |
|
Our driver supports overlay planes, and as expected, some userspace
compositor takes advantage of these features. If the userspace is not
enabling the cursor, they can use multiple planes as they please.
Nevertheless, we start to have constraints when userspace tries to
enable hardware cursor with various planes. Basically, we cannot draw
the cursor at the same size and position on two separated pipes since it
uses extra bandwidth and DML only run with one cursor.
For those reasons, when we enable hardware cursor and multiple planes,
our driver should accept variations like the ones described below:
+-------------+ +--------------+
| +---------+ | | |
| |Primary | | | Primary |
| | | | | Overlay |
| +---------+ | | |
|Overlay | | |
+-------------+ +--------------+
In this scenario, we can have the desktop UI in the overlay and some
other framebuffer attached to the primary plane (e.g., video). However,
userspace needs to obey some rules and avoid scenarios like the ones
described below (when enabling hw cursor):
+--------+
|Overlay |
+-------------+ +-----+-------+ +-| |--+
| +--------+ | +--------+ | | +--------+ |
| |Overlay | | |Overlay | | | |
| | | | | | | | |
| +--------+ | +--------+ | | |
| Primary | | Primary | | Primary |
+-------------+ +-------------+ +-------------+
+-------------+ +-------------+
| +--------+ | Primary |
| |Overlay | | |
| | | | |
| +--------+ | +--------+ |
| Primary | | |Overlay | |
+-------------+ +-| |--+
+--------+
If the userspace violates some of the above scenarios, our driver needs
to reject the commit; otherwise, we can have unexpected behavior. Since
we don't have a proper driver validation for the above case, we can see
some problems like a duplicate cursor in applications that use multiple
planes. This commit fixes the cursor issue and others by adding adequate
verification for multiple planes.
Change since V1 (Harry and Sean):
- Remove cursor verification from the equation.
Cc: Louis Li <Ching-shih.Li@amd.com>
Cc: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Cc: Harry Wentland <Harry.Wentland@amd.com>
Cc: Hersen Wu <hersenxs.wu@amd.com>
Cc: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Polaris12 32bit ASIC needs a special MC firmware.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
This error code-path is missing a drm_gem_object_put call. Other
error code-paths are fine.
Signed-off-by: Simon Ser <contact@emersion.fr>
Fixes: 1769152ac64b ("drm/amdgpu: Fail fb creation from imported dma-bufs. (v2)")
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Harry Wentland <hwentlan@amd.com>
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Cc: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
When an amdgpu device fails to init, it makes another VGA device cause
kernel splat:
kernel: amdgpu 0000:08:00.0: amdgpu: amdgpu_device_ip_init failed
kernel: amdgpu 0000:08:00.0: amdgpu: Fatal error during GPU init
kernel: amdgpu: probe of 0000:08:00.0 failed with error -110
...
kernel: amdgpu 0000:01:00.0: vgaarb: changed VGA decodes: olddecodes=io+mem,decodes=none:owns=none
kernel: BUG: kernel NULL pointer dereference, address: 0000000000000018
kernel: #PF: supervisor read access in kernel mode
kernel: #PF: error_code(0x0000) - not-present page
kernel: PGD 0 P4D 0
kernel: Oops: 0000 [#1] SMP NOPTI
kernel: CPU: 6 PID: 1080 Comm: Xorg Tainted: G W 5.12.0-rc8+ #12
kernel: Hardware name: HP HP EliteDesk 805 G6/872B, BIOS S09 Ver. 02.02.00 12/30/2020
kernel: RIP: 0010:amdgpu_device_vga_set_decode+0x13/0x30 [amdgpu]
kernel: Code: 06 31 c0 c3 b8 ea ff ff ff 5d c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 0f 1f 44 00 00 55 48 8b 87 90 06 00 00 48 89 e5 53 89 f3 <48> 8b 40 18 40 0f b6 f6 e8 40 58 39 fd 80 fb 01 5b 5d 19 c0 83 e0
kernel: RSP: 0018:ffffae3c0246bd68 EFLAGS: 00010002
kernel: RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
kernel: RDX: ffff8dd1af5a8560 RSI: 0000000000000000 RDI: ffff8dce8c160000
kernel: RBP: ffffae3c0246bd70 R08: ffff8dd1af5985c0 R09: ffffae3c0246ba38
kernel: R10: 0000000000000001 R11: 0000000000000001 R12: 0000000000000246
kernel: R13: 0000000000000000 R14: 0000000000000003 R15: ffff8dce81490000
kernel: FS: 00007f9303d8fa40(0000) GS:ffff8dd1af580000(0000) knlGS:0000000000000000
kernel: CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
kernel: CR2: 0000000000000018 CR3: 0000000103cfa000 CR4: 0000000000350ee0
kernel: Call Trace:
kernel: vga_arbiter_notify_clients.part.0+0x4a/0x80
kernel: vga_get+0x17f/0x1c0
kernel: vga_arb_write+0x121/0x6a0
kernel: ? apparmor_file_permission+0x1c/0x20
kernel: ? security_file_permission+0x30/0x180
kernel: vfs_write+0xca/0x280
kernel: ksys_write+0x67/0xe0
kernel: __x64_sys_write+0x1a/0x20
kernel: do_syscall_64+0x38/0x90
kernel: entry_SYSCALL_64_after_hwframe+0x44/0xae
kernel: RIP: 0033:0x7f93041e02f7
kernel: Code: 75 05 48 83 c4 58 c3 e8 f7 33 ff ff 0f 1f 80 00 00 00 00 f3 0f 1e fa 64 8b 04 25 18 00 00 00 85 c0 75 10 b8 01 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 51 c3 48 83 ec 28 48 89 54 24 18 48 89 74 24
kernel: RSP: 002b:00007fff60e49b28 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
kernel: RAX: ffffffffffffffda RBX: 000000000000000b RCX: 00007f93041e02f7
kernel: RDX: 000000000000000b RSI: 00007fff60e49b40 RDI: 000000000000000f
kernel: RBP: 00007fff60e49b40 R08: 00000000ffffffff R09: 00007fff60e499d0
kernel: R10: 00007f93049350b5 R11: 0000000000000246 R12: 000056111d45e808
kernel: R13: 0000000000000000 R14: 000056111d45e7f8 R15: 000056111d46c980
kernel: Modules linked in: nls_iso8859_1 snd_hda_codec_realtek snd_hda_codec_generic ledtrig_audio snd_hda_codec_hdmi snd_hda_intel snd_intel_dspcfg snd_hda_codec snd_hwdep snd_hda_core snd_pcm snd_seq input_leds snd_seq_device snd_timer snd soundcore joydev kvm_amd serio_raw k10temp mac_hid hp_wmi ccp kvm sparse_keymap wmi_bmof ucsi_acpi efi_pstore typec_ucsi rapl typec video wmi sch_fq_codel parport_pc ppdev lp parport ip_tables x_tables autofs4 btrfs blake2b_generic zstd_compress raid10 raid456 async_raid6_recov async_memcpy async_pq async_xor async_tx libcrc32c xor raid6_pq raid1 raid0 multipath linear dm_mirror dm_region_hash dm_log hid_generic usbhid hid amdgpu drm_ttm_helper ttm iommu_v2 gpu_sched i2c_algo_bit drm_kms_helper syscopyarea sysfillrect crct10dif_pclmul sysimgblt crc32_pclmul fb_sys_fops ghash_clmulni_intel cec rc_core aesni_intel crypto_simd psmouse cryptd r8169 i2c_piix4 drm ahci xhci_pci realtek libahci xhci_pci_renesas gpio_amdpt gpio_generic
kernel: CR2: 0000000000000018
kernel: ---[ end trace 76d04313d4214c51 ]---
Commit 4192f7b57689 ("drm/amdgpu: unmap register bar on device init
failure") makes amdgpu_driver_unload_kms() skips amdgpu_device_fini(),
so the VGA clients remain registered. So when
vga_arbiter_notify_clients() iterates over registered clients, it causes
NULL pointer dereference.
Since there's no reason to register VGA clients that early, so solve
the issue by putting them after all the goto cleanups.
v2:
- Remove redundant vga_switcheroo cleanup in failed: label.
Fixes: 4192f7b57689 ("drm/amdgpu: unmap register bar on device init failure")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The runtime resume PM op disregards the return value from
amdgpu_device_resume(), masking errors for failed resumes at the PM
layer.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Pavan Kumar Ramayanam <pavan.ramayanam@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Sriov gets suspend of IP block <dce_virtual> failed as return
value was not initialized.
v2: return 0 directly to align original code semantic before this
was broken out into a separate helper function instead of setting
initial values
Signed-off-by: Victor Zhao <Victor.Zhao@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
[why]
Previous statement would always evaluate to true
making it meaningless
[how]
Just check if a connector is MST by checking if its port exists.
Fixes: 41efcd3879b1df ("drm/amd/display: Add MST capability to trigger_hotplug interface")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Wayne Lin <waynelin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
v2 : change condition to apply to all chips after NAVI10
Writing to dcefclk causes the gpu to become unresponsive, and requires a reboot.
Patch prevents user from successfully writing to file pp_dpm_dcefclk on parts
NAVI10 and newer, and gives better user feedback that this operation is not allowed.
Signed-off-by: Darren Powell <darren.powell@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Writing to dcefclk causes the gpu to become unresponsive, and requires a reboot.
Patch ignores a .force_clk_levels(SMU_DCEFCLK) call and issues an
info message.
Signed-off-by: Darren Powell <darren.powell@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Starting with Vega the hardware supports concurrent flushes
of VMID which can be used to implement per process VMID
allocation.
But concurrent flushes are mutual exclusive with back to
back VMID allocations, fix this to avoid a VMID used in
two ways at the same time.
v2: don't set ring to NULL
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: James Zhu <James.Zhu@amd.com>
Tested-by: James Zhu <James.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
[Why]
This hasn't been well tested and leads to complete system hangs on DCN1
based systems, possibly others.
The system hang can be reproduced by gesturing the video on the YouTube
Android app on ChromeOS into full screen.
[How]
Reject atomic commits with non-zero drm_plane_state.src_x or src_y values.
v2:
- Add code comment describing the reason we're rejecting non-zero
src_x and src_y
- Drop gerrit Change-Id
- Add stable CC
- Based on amd-staging-drm-next
v3: removed trailing whitespace
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Cc: stable@vger.kernel.org
Cc: nicholas.kazlauskas@amd.com
Cc: amd-gfx@lists.freedesktop.org
Cc: alexander.deucher@amd.com
Cc: Roman.Li@amd.com
Cc: hersenxs.wu@amd.com
Cc: danny.wang@amd.com
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-next
A few fixes for the next merge window, with some build fixes for anx7625
and lt8912b bridges, incorrect error handling for lt8912b and TTM, and
one fix for TTM page limit accounting.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210422163329.dvbuwre3akwdmzjt@gilmour
|
|
Pages in SG BOs were not allocated by TTM. So don't count them against
TTM's pages limit.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210414064804.29356-9-Felix.Kuehling@amd.com
|
|
The function returns the number of swapped pages here. Only abort when we get
a negative error code.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210409130113.1459-1-christian.koenig@amd.com
|
|
A static analysis shows several issues in the driver code at
probing time.
DT parsing errors were bad handled and could lead to bugs:
- Bad error detection;
- Bad release of resources
Fixes: 30e2ae943c26 ("drm/bridge: Introduce LT8912B DSI to HDMI bridge")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Suggested-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210415183639.1487-1-rdunlap@infradead.org
Signed-off-by: Robert Foss <robert.foss@linaro.org>
|
|
The Lontium DRM bridge drivers use mipi_dsi_() function interfaces so
they need to select DRM_MIPI_DSI to prevent build errors.
ERROR: modpost: "mipi_dsi_attach" [drivers/gpu/drm/bridge/lontium-lt9611uxc.ko] undefined!
ERROR: modpost: "mipi_dsi_device_register_full" [drivers/gpu/drm/bridge/lontium-lt9611uxc.ko] undefined!
ERROR: modpost: "of_find_mipi_dsi_host_by_node" [drivers/gpu/drm/bridge/lontium-lt9611uxc.ko] undefined!
ERROR: modpost: "mipi_dsi_device_unregister" [drivers/gpu/drm/bridge/lontium-lt9611uxc.ko] undefined!
ERROR: modpost: "mipi_dsi_detach" [drivers/gpu/drm/bridge/lontium-lt9611uxc.ko] undefined!
ERROR: modpost: "mipi_dsi_attach" [drivers/gpu/drm/bridge/lontium-lt9611.ko] undefined!
ERROR: modpost: "mipi_dsi_device_register_full" [drivers/gpu/drm/bridge/lontium-lt9611.ko] undefined!
ERROR: modpost: "of_find_mipi_dsi_host_by_node" [drivers/gpu/drm/bridge/lontium-lt9611.ko] undefined!
ERROR: modpost: "mipi_dsi_device_unregister" [drivers/gpu/drm/bridge/lontium-lt9611.ko] undefined!
ERROR: modpost: "mipi_dsi_detach" [drivers/gpu/drm/bridge/lontium-lt9611.ko] undefined!
WARNING: modpost: suppressed 5 unresolved symbol warnings because there were too many)
Fixes: 23278bf54afe ("drm/bridge: Introduce LT9611 DSI to HDMI bridge")
Fixes: 0cbbd5b1a012 ("drm: bridge: add support for lontium LT9611UXC bridge")
Fixes: 30e2ae943c26 ("drm/bridge: Introduce LT8912B DSI to HDMI bridge")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Adren Grassein <adrien.grassein@gmail.com>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Adrien Grassein <adrien.grassein@gmail.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: dri-devel@lists.freedesktop.org
Cc: stable@vger.kernel.org
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210415183639.1487-1-rdunlap@infradead.org
|
|
The Analogix DRM ANX7625 bridge driver uses mips_dsi_() function
interfaces so it should select DRM_MIPI_DSI to prevent build errors.
ERROR: modpost: "mipi_dsi_attach" [drivers/gpu/drm/bridge/analogix/anx7625.ko] undefined!
ERROR: modpost: "mipi_dsi_device_register_full" [drivers/gpu/drm/bridge/analogix/anx7625.ko] undefined!
ERROR: modpost: "of_find_mipi_dsi_host_by_node" [drivers/gpu/drm/bridge/analogix/anx7625.ko] undefined!
ERROR: modpost: "mipi_dsi_device_unregister" [drivers/gpu/drm/bridge/analogix/anx7625.ko] undefined!
ERROR: modpost: "mipi_dsi_detach" [drivers/gpu/drm/bridge/analogix/anx7625.ko] undefined!
Fixes: 8bdfc5dae4e3 ("drm/bridge: anx7625: Add anx7625 MIPI DSI/DPI to DP")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Cc: Xin Ji <xji@analogixsemi.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: dri-devel@lists.freedesktop.org
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210415183619.1431-1-rdunlap@infradead.org
|
|
https://gitlab.freedesktop.org/drm/msm into drm-next
msm-next from Rob:
* Big DSI phy/pll cleanup. Includes some clk patches, acked by
maintainer
* Initial support for sc7280
* compatibles fixes for sm8150/sm8250
* cleanups for all dpu gens to use same bandwidth scaling paths (\o/)
* various shrinker path lock contention optimizations
* unpin/swap support for GEM objects (disabled by default, enable with
msm.enable_eviction=1 .. due to various combinations of iommu drivers
with older gens I want to get more testing on hw I don't have in front
of me before enabling by default)
* The usual assortment of misc fixes and cleanups
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGvL=4aw15qoY8fbKG9FCgnx8Y-dCtf7xiFwTQSHopwSQg@mail.gmail.com
|
|
msm-next pull request has a baseline with stuff from -fixes, roll
forward first.
Some simple conflicts in amdgpu, ttm and one in i915 where git gets
confused and tries to add the same function twice.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
https://gitlab.freedesktop.org/agd5f/linux into drm-next
amd-drm-next-5.13-2021-04-12:
amdgpu:
- Re-enable GPU reset on VanGogh
- Enable DPM flags for SMART_SUSPEND and MAY_SKIP_RESUME
- Disentangle HG from vga_switcheroo
- S0ix fixes
- W=1 fixes
- Resource iterator fixes
- DMCUB updates
- UBSAN fixes
- More PM API cleanup
- Aldebaran updates
- Modifier fixes
- Enable VCN load balancing with asymmetric engines
- Rework BO structs
- Aldebaran reset support
- Initial LTTPR display work
- Display MALL fixes
- Fall back to YCbCr420 when YCbCr444 fails
- SR-IOV fixes
- RAS updates
- Misc cleanups and fixes
radeon:
- Typo fixes
- Fix error handling for firmware on r6xx
- Fix a missing check in DP MST handling
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210412220732.3845-1-alexander.deucher@amd.com
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fix from David Sterba:
"One more patch that we'd like to get to 5.12 before release.
It's changing where and how the superblock is stored in the zoned
mode. It is an on-disk format change but so far there are no
implications for users as the proper mkfs support hasn't been merged
and is waiting for the kernel side to settle.
Until now, the superblocks were derived from the zone index, but zone
size can differ per device. This is changed to be based on fixed
offset values, to make it independent of the device zone size.
The work on that got a bit delayed, we discussed the exact locations
to support potential device sizes and usecases. (Partially delayed
also due to my vacation.) Having that in the same release where the
zoned mode is declared usable is highly desired, there are userspace
projects that need to be updated to recognize the feature. Pushing
that to the next release would make things harder to test"
* tag 'for-5.12-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: zoned: move superblock logging zone location
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixlets from Ingo Molnar:
"Two minor fixes: one for a Clang warning, the other improves an
ambiguous/confusing kernel log message"
* tag 'locking-urgent-2021-04-11' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
lockdep: Address clang -Wformat warning printing for %hd
lockdep: Add a missing initialization hint to the "INFO: Trying to register non-static key" message
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
- Fix the vDSO exception handling return path to disable interrupts
again.
- A fix for the CE collector to return the proper return values to its
callers which are used to convey what the collector has done with the
error address.
* tag 'x86_urgent_for_v5.12-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/traps: Correct exc_general_protection() and math_error() return paths
RAS/CEC: Correct ce_add_elem()'s returned values
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dennis/percpu
Pull percpu fix from Dennis Zhou:
"This contains a fix for sporadically failing atomic percpu
allocations.
I only caught it recently while I was reviewing a new series [1] and
simultaneously saw reports by btrfs in xfstests [2] and [3].
In v5.9, memcg accounting was extended to percpu done by adding a
second type of chunk. I missed an interaction with the free page float
count used to ensure we can support atomic allocations. If one type of
chunk has no free pages, but the other has enough to satisfy the free
page float requirement, we will not repopulate the free pages for the
former type of chunk. This led to the sporadically failing atomic
allocations"
Link: https://lore.kernel.org/linux-mm/20210324190626.564297-1-guro@fb.com/ [1]
Link: https://lore.kernel.org/linux-mm/20210401185158.3275.409509F4@e16-tech.com/ [2]
Link: https://lore.kernel.org/linux-mm/CAL3q7H5RNBjCi708GH7jnczAOe0BLnacT9C+OBgA-Dx9jhB6SQ@mail.gmail.com/ [3]
* 'for-5.12-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/dennis/percpu:
percpu: make pcpu_nr_empty_pop_pages per chunk type
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Seven fixes, all in drivers.
The hpsa three are the most extensive and the most problematic: it's a
packed structure misalignment that oopses on ia64 but looks like it
would also oops on quite a few non-x86 architectures.
The pm80xx is a regression and the rest are bug fixes for patches in
the misc tree"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: scsi_transport_srp: Don't block target in SRP_PORT_LOST state
scsi: target: iscsi: Fix zero tag inside a trace event
scsi: pm80xx: Fix chip initialization failure
scsi: ufs: core: Fix wrong Task Tag used in task management request UPIUs
scsi: ufs: core: Fix task management request completion timeout
scsi: hpsa: Add an assert to prevent __packed reintroduction
scsi: hpsa: Fix boot on ia64 (atomic_t alignment)
scsi: hpsa: Use __packed on individual structs, not header-wide
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Some some more powerpc fixes for 5.12:
- Fix an oops triggered by ptrace when CONFIG_PPC_FPU_REGS=n
- Fix an oops on sigreturn when the VDSO is unmapped on 32-bit
- Fix vdso_wrapper.o not being rebuilt everytime vdso.so is rebuilt
Thanks to Christophe Leroy"
* tag 'powerpc-5.12-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/vdso: Make sure vdso_wrapper.o is rebuilt everytime vdso.so is rebuilt
powerpc/signal32: Fix Oops on sigreturn with unmapped VDSO
powerpc/ptrace: Don't return error when getting/setting FP regs without CONFIG_PPC_FPU_REGS
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fix from Greg KH:
"Here is a single driver core fix for 5.12-rc7 to resolve a reported
problem that caused some devices to lockup when booting. It has been
in linux-next with no reported issues"
* tag 'driver-core-5.12-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
driver core: Fix locking bug in deferred_probe_timeout_work_func()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/Thunderbolt fixes from Greg KH:
"Here are a few small USB and Thunderbolt driver fixes for 5.12-rc7 for
reported issues:
- thunderbolt leaks and off-by-one fix
- cdnsp deque fix
- usbip fixes for syzbot-reported issues
All have been in linux-next with no reported problems"
* tag 'usb-5.12-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usbip: synchronize event handler with sysfs code paths
usbip: vudc synchronize sysfs code paths
usbip: stub-dev synchronize sysfs code paths
usbip: add sysfs_lock to synchronize sysfs code paths
thunderbolt: Fix off by one in tb_port_find_retimer()
thunderbolt: Fix a leak in tb_retimer_add()
usb: cdnsp: Fixes issue with dequeuing requests after disabling endpoint
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"A mixture of driver and documentation bugfixes for I2C"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: imx: mention Oleksij as maintainer of the binding docs
i2c: exynos5: correct top kerneldoc
i2c: designware: Adjust bus_freq_hz when refuse high speed mode set
i2c: hix5hd2: use the correct HiSilicon copyright
i2c: gpio: update email address in binding docs
i2c: imx: drop me as maintainer of binding docs
i2c: stm32f4: Mundane typo fix
I2C: JZ4780: Fix bug for Ingenic X1000.
i2c: turn recovery error on init to debug
|
|
Moves the location of the superblock logging zones. The new locations of
the logging zones are now determined based on fixed block addresses
instead of on fixed zone numbers.
The old placement method based on fixed zone numbers causes problems when
one needs to inspect a file system image without access to the drive zone
information. In such case, the super block locations cannot be reliably
determined as the zone size is unknown. By locating the superblock logging
zones using fixed addresses, we can scan a dumped file system image without
the zone information since a super block copy will always be present at or
after the fixed known locations.
Introduce the following three pairs of zones containing fixed offset
locations, regardless of the device zone size.
- primary superblock: offset 0B (and the following zone)
- first copy: offset 512G (and the following zone)
- Second copy: offset 4T (4096G, and the following zone)
If a logging zone is outside of the disk capacity, we do not record the
superblock copy.
The first copy position is much larger than for a non-zoned filesystem,
which is at 64M. This is to avoid overlapping with the log zones for
the primary superblock. This higher location is arbitrary but allows
supporting devices with very large zone sizes, plus some space around in
between.
Such large zone size is unrealistic and very unlikely to ever be seen in
real devices. Currently, SMR disks have a zone size of 256MB, and we are
expecting ZNS drives to be in the 1-4GB range, so this limit gives us
room to breathe. For now, we only allow zone sizes up to 8GB. The
maximum zone size that would still fit in the space is 256G.
The fixed location addresses are somewhat arbitrary, with the intent of
maintaining superblock reliability for smaller and larger devices, with
the preference for the latter. For this reason, there are two superblocks
under the first 1T. This should cover use cases for physical devices and
for emulated/device-mapper devices.
The superblock logging zones are reserved for superblock logging and
never used for data or metadata blocks. Note that we only reserve the
two zones per primary/copy actually used for superblock logging. We do
not reserve the ranges of zones possibly containing superblocks with the
largest supported zone size (0-16GB, 512G-528GB, 4096G-4112G).
The zones containing the fixed location offsets used to store
superblocks on a non-zoned volume are also reserved to avoid confusion.
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"Here's the latest pile of clk driver and clk framework fixes for this
release:
- Two clk framework fixes for a long standing issue in
clk_notifier_{register,unregister}() where we used a pointer that
was for a struct containing a list head when there was no container
struct
- A compile warning fix for socfpga that's good to have
- A double free problem with devm registered fixed factor clks
- One last fix to the Qualcomm camera clk driver to use the right clk
ops so clks don't get stuck and stop working because the firmware
takes them for a ride"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: fixed: fix double free in resource managed fixed-factor clock
clk: fix invalid usage of list cursor in unregister
clk: fix invalid usage of list cursor in register
clk: qcom: camcc: Update the clock ops for the SC7180
clk: socfpga: fix iomem pointer cast on 64-bit
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux
Pull perf tool fixes from Arnaldo Carvalho de Melo:
- Fix wrong LBR block sorting in 'perf report'
- Fix 'perf inject' repipe usage when consuming perf.data files
- Avoid potential buffer overrun when decoding ARM SPE hardware tracing
packets, bug found using a fuzzer
* tag 'perf-tools-fixes-for-v5.12-2020-04-09' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
perf arm-spe: Avoid potential buffer overrun
perf report: Fix wrong LBR block sorting
perf inject: Fix repipe usage
|
|
Merge misc fixes from Andrew Morton:
"14 patches.
Subsystems affected by this patch series: mm (kasan, gup, pagecache,
and kfence), MAINTAINERS, mailmap, nds32, gcov, ocfs2, ia64, and lib"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
lib: fix kconfig dependency on ARCH_WANT_FRAME_POINTERS
kfence, x86: fix preemptible warning on KPTI-enabled systems
lib/test_kasan_module.c: suppress unused var warning
kasan: fix conflict with page poisoning
fs: direct-io: fix missing sdio->boundary
ia64: fix user_stack_pointer() for ptrace()
ocfs2: fix deadlock between setattr and dio_end_io_write
gcov: re-fix clang-11+ support
nds32: flush_dcache_page: use page_mapping_file to avoid races with swapoff
mm/gup: check page posion status for coredump.
.mailmap: fix old email addresses
mailmap: update email address for Jordan Crouse
treewide: change my e-mail address, fix my name
MAINTAINERS: update CZ.NIC's Turris information
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Networking fixes for 5.12-rc7, including fixes from can, ipsec,
mac80211, wireless, and bpf trees.
No scary regressions here or in the works, but small fixes for 5.12
changes keep coming.
Current release - regressions:
- virtio: do not pull payload in skb->head
- virtio: ensure mac header is set in virtio_net_hdr_to_skb()
- Revert "net: correct sk_acceptq_is_full()"
- mptcp: revert "mptcp: provide subflow aware release function"
- ethernet: lan743x: fix ethernet frame cutoff issue
- dsa: fix type was not set for devlink port
- ethtool: remove link_mode param and derive link params from driver
- sched: htb: fix null pointer dereference on a null new_q
- wireless: iwlwifi: Fix softirq/hardirq disabling in
iwl_pcie_enqueue_hcmd()
- wireless: iwlwifi: fw: fix notification wait locking
- wireless: brcmfmac: p2p: Fix deadlock introduced by avoiding the
rtnl dependency
Current release - new code bugs:
- napi: fix hangup on napi_disable for threaded napi
- bpf: take module reference for trampoline in module
- wireless: mt76: mt7921: fix airtime reporting and related tx hangs
- wireless: iwlwifi: mvm: rfi: don't lock mvm->mutex when sending
config command
Previous releases - regressions:
- rfkill: revert back to old userspace API by default
- nfc: fix infinite loop, refcount & memory leaks in LLCP sockets
- let skb_orphan_partial wake-up waiters
- xfrm/compat: Cleanup WARN()s that can be user-triggered
- vxlan, geneve: do not modify the shared tunnel info when PMTU
triggers an ICMP reply
- can: fix msg_namelen values depending on CAN_REQUIRED_SIZE
- can: uapi: mark union inside struct can_frame packed
- sched: cls: fix action overwrite reference counting
- sched: cls: fix err handler in tcf_action_init()
- ethernet: mlxsw: fix ECN marking in tunnel decapsulation
- ethernet: nfp: Fix a use after free in nfp_bpf_ctrl_msg_rx
- ethernet: i40e: fix receiving of single packets in xsk zero-copy
mode
- ethernet: cxgb4: avoid collecting SGE_QBASE regs during traffic
Previous releases - always broken:
- bpf: Refuse non-O_RDWR flags in BPF_OBJ_GET
- bpf: Refcount task stack in bpf_get_task_stack
- bpf, x86: Validate computation of branch displacements
- ieee802154: fix many similar syzbot-found bugs
- fix NULL dereferences in netlink attribute handling
- reject unsupported operations on monitor interfaces
- fix error handling in llsec_key_alloc()
- xfrm: make ipv4 pmtu check honor ip header df
- xfrm: make hash generation lock per network namespace
- xfrm: esp: delete NETIF_F_SCTP_CRC bit from features for esp
offload
- ethtool: fix incorrect datatype in set_eee ops
- xdp: fix xdp_return_frame() kernel BUG throw for page_pool memory
model
- openvswitch: fix send of uninitialized stack memory in ct limit
reply
Misc:
- udp: add get handling for UDP_GRO sockopt"
* tag 'net-5.12-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (182 commits)
net: fix hangup on napi_disable for threaded napi
net: hns3: Trivial spell fix in hns3 driver
lan743x: fix ethernet frame cutoff issue
net: ipv6: check for validity before dereferencing cfg->fc_nlinfo.nlh
net: dsa: lantiq_gswip: Configure all remaining GSWIP_MII_CFG bits
net: dsa: lantiq_gswip: Don't use PHY auto polling
net: sched: sch_teql: fix null-pointer dereference
ipv6: report errors for iftoken via netlink extack
net: sched: fix err handler in tcf_action_init()
net: sched: fix action overwrite reference counting
Revert "net: sched: bump refcount for new action in ACT replace mode"
ice: fix memory leak of aRFS after resuming from suspend
i40e: Fix sparse warning: missing error code 'err'
i40e: Fix sparse error: 'vsi->netdev' could be null
i40e: Fix sparse error: uninitialized symbol 'ring'
i40e: Fix sparse errors in i40e_txrx.c
i40e: Fix parameters in aq_get_phy_register()
nl80211: fix beacon head validation
bpf, x86: Validate computation of branch displacements for x86-32
bpf, x86: Validate computation of branch displacements for x86-64
...
|
|
Pull io_uring fixes from Jens Axboe:
"Two minor fixups for the reissue logic, and one for making sure that
unbounded work is canceled on io-wq exit"
* tag 'io_uring-5.12-2021-04-09' of git://git.kernel.dk/linux-block:
io-wq: cancel unbounded works on io-wq destroy
io_uring: fix rw req completion
io_uring: clear F_REISSUE right after getting it
|
|
When LATENCYTOP, LOCKDEP, or FAULT_INJECTION_STACKTRACE_FILTER is
enabled and ARCH_WANT_FRAME_POINTERS is disabled, Kbuild gives a warning
such as:
WARNING: unmet direct dependencies detected for FRAME_POINTER
Depends on [n]: DEBUG_KERNEL [=y] && (M68K || UML || SUPERH) || ARCH_WANT_FRAME_POINTERS [=n] || MCOUNT [=n]
Selected by [y]:
- LATENCYTOP [=y] && DEBUG_KERNEL [=y] && STACKTRACE_SUPPORT [=y] && PROC_FS [=y] && !MIPS && !PPC && !S390 && !MICROBLAZE && !ARM && !ARC && !X86
Depending on ARCH_WANT_FRAME_POINTERS causes a recursive dependency
error. ARCH_WANT_FRAME_POINTERS is to be selected by the architecture,
and is not supposed to be overridden by other config options.
Link: https://lkml.kernel.org/r/20210329165329.27994-1-julianbraha@gmail.com
Signed-off-by: Julian Braha <julianbraha@gmail.com>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Necip Fazil Yildiran <fazilyildiran@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
On systems with KPTI enabled, we can currently observe the following
warning:
BUG: using smp_processor_id() in preemptible
caller is invalidate_user_asid+0x13/0x50
CPU: 6 PID: 1075 Comm: dmesg Not tainted 5.12.0-rc4-gda4a2b1a5479-kfence_1+ #1
Hardware name: Hewlett-Packard HP Pro 3500 Series/2ABF, BIOS 8.11 10/24/2012
Call Trace:
dump_stack+0x7f/0xad
check_preemption_disabled+0xc8/0xd0
invalidate_user_asid+0x13/0x50
flush_tlb_one_kernel+0x5/0x20
kfence_protect+0x56/0x80
...
While it normally makes sense to require preemption to be off, so that
the expected CPU's TLB is flushed and not another, in our case it really
is best-effort (see comments in kfence_protect_page()).
Avoid the warning by disabling preemption around flush_tlb_one_kernel().
Link: https://lore.kernel.org/lkml/YGIDBAboELGgMgXy@elver.google.com/
Link: https://lkml.kernel.org/r/20210330065737.652669-1-elver@google.com
Signed-off-by: Marco Elver <elver@google.com>
Reported-by: Tomi Sarvela <tomi.p.sarvela@intel.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Andrey Konovalov <andreyknvl@google.com>
Cc: Jann Horn <jannh@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Local `unused' is intentionally unused - it is there to suppress
__must_check warnings.
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lkml.kernel.org/r/202104050216.HflRxfJm-lkp@intel.com
Cc: Marco Elver <elver@google.com>
Cc: Alexander Potapenko <glider@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When page poisoning is enabled, it accesses memory that is marked as
poisoned by KASAN, which leas to false-positive KASAN reports.
Suppress the reports by adding KASAN annotations to unpoison_page()
(poison_page() already has them).
Link: https://lkml.kernel.org/r/2dc799014d31ac13fd97bd906bad33e16376fc67.1617118501.git.andreyknvl@google.com
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Marco Elver <elver@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Andrey Konovalov <andreyknvl@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
I encountered a hung task issue, but not a performance one. I run DIO
on a device (need lba continuous, for example open channel ssd), maybe
hungtask in below case:
DIO: Checkpoint:
get addr A(at boundary), merge into BIO,
no submit because boundary missing
flush dirty data(get addr A+1), wait IO(A+1)
writeback timeout, because DIO(A) didn't submit
get addr A+2 fail, because checkpoint is doing
dio_send_cur_page() may clear sdio->boundary, so prevent it from missing
a boundary.
Link: https://lkml.kernel.org/r/20210322042253.38312-1-jack.qiu@huawei.com
Fixes: b1058b981272 ("direct-io: submit bio after boundary buffer is added to it")
Signed-off-by: Jack Qiu <jack.qiu@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
ia64 has two stacks:
- memory stack (or stack), pointed at by by r12
- register backing store (register stack), pointed at by
ar.bsp/ar.bspstore with complications around dirty
register frame on CPU.
In [1] Dmitry noticed that PTRACE_GET_SYSCALL_INFO returns the register
stack instead memory stack.
The bug comes from the fact that user_stack_pointer() and
current_user_stack_pointer() don't return the same register:
ulong user_stack_pointer(struct pt_regs *regs) { return regs->ar_bspstore; }
#define current_user_stack_pointer() (current_pt_regs()->r12)
The change gets both back in sync.
I think ptrace(PTRACE_GET_SYSCALL_INFO) is the only affected user by
this bug on ia64.
The change fixes 'rt_sigreturn.gen.test' strace test where it was
observed initially.
Link: https://bugs.gentoo.org/769614 [1]
Link: https://lkml.kernel.org/r/20210331084447.2561532-1-slyfox@gentoo.org
Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org>
Reported-by: Dmitry V. Levin <ldv@altlinux.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The following deadlock is detected:
truncate -> setattr path is waiting for pending direct IO to be done (inode->i_dio_count become zero) with inode->i_rwsem held (down_write).
PID: 14827 TASK: ffff881686a9af80 CPU: 20 COMMAND: "ora_p005_hrltd9"
#0 __schedule at ffffffff818667cc
#1 schedule at ffffffff81866de6
#2 inode_dio_wait at ffffffff812a2d04
#3 ocfs2_setattr at ffffffffc05f322e [ocfs2]
#4 notify_change at ffffffff812a5a09
#5 do_truncate at ffffffff812808f5
#6 do_sys_ftruncate.constprop.18 at ffffffff81280cf2
#7 sys_ftruncate at ffffffff81280d8e
#8 do_syscall_64 at ffffffff81003949
#9 entry_SYSCALL_64_after_hwframe at ffffffff81a001ad
dio completion path is going to complete one direct IO (decrement
inode->i_dio_count), but before that it hung at locking inode->i_rwsem:
#0 __schedule+700 at ffffffff818667cc
#1 schedule+54 at ffffffff81866de6
#2 rwsem_down_write_failed+536 at ffffffff8186aa28
#3 call_rwsem_down_write_failed+23 at ffffffff8185a1b7
#4 down_write+45 at ffffffff81869c9d
#5 ocfs2_dio_end_io_write+180 at ffffffffc05d5444 [ocfs2]
#6 ocfs2_dio_end_io+85 at ffffffffc05d5a85 [ocfs2]
#7 dio_complete+140 at ffffffff812c873c
#8 dio_aio_complete_work+25 at ffffffff812c89f9
#9 process_one_work+361 at ffffffff810b1889
#10 worker_thread+77 at ffffffff810b233d
#11 kthread+261 at ffffffff810b7fd5
#12 ret_from_fork+62 at ffffffff81a0035e
Thus above forms ABBA deadlock. The same deadlock was mentioned in
upstream commit 28f5a8a7c033 ("ocfs2: should wait dio before inode lock
in ocfs2_setattr()"). It seems that that commit only removed the
cluster lock (the victim of above dead lock) from the ABBA deadlock
party.
End-user visible effects: Process hang in truncate -> ocfs2_setattr path
and other processes hang at ocfs2_dio_end_io_write path.
This is to fix the deadlock itself. It removes inode_lock() call from
dio completion path to remove the deadlock and add ip_alloc_sem lock in
setattr path to synchronize the inode modifications.
[wen.gang.wang@oracle.com: remove the "had_alloc_lock" as suggested]
Link: https://lkml.kernel.org/r/20210402171344.1605-1-wen.gang.wang@oracle.com
Link: https://lkml.kernel.org/r/20210331203654.3911-1-wen.gang.wang@oracle.com
Signed-off-by: Wengang Wang <wen.gang.wang@oracle.com>
Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Gang He <ghe@suse.com>
Cc: Jun Piao <piaojun@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
LLVM changed the expected function signature for llvm_gcda_emit_function()
in the clang-11 release. Users of clang-11 or newer may have noticed
their kernels producing invalid coverage information:
$ llvm-cov gcov -a -c -u -f -b <input>.gcda -- gcno=<input>.gcno
1 <func>: checksum mismatch, \
(<lineno chksum A>, <cfg chksum B>) != (<lineno chksum A>, <cfg chksum C>)
2 Invalid .gcda File!
...
Fix up the function signatures so calling this function interprets its
parameters correctly and computes the correct cfg checksum. In
particular, in clang-11, the additional checksum is no longer optional.
Link: https://reviews.llvm.org/rG25544ce2df0daa4304c07e64b9c8b0f7df60c11d
Link: https://lkml.kernel.org/r/20210408184631.1156669-1-ndesaulniers@google.com
Reported-by: Prasad Sodagudi <psodagud@quicinc.com>
Tested-by: Prasad Sodagudi <psodagud@quicinc.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Cc: <stable@vger.kernel.org> [5.4+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit cb9f753a3731 ("mm: fix races between swapoff and flush dcache")
updated flush_dcache_page implementations on several architectures to
use page_mapping_file() in order to avoid races between page_mapping()
and swapoff().
This update missed arch/nds32 and there is a possibility of a race
there.
Replace page_mapping() with page_mapping_file() in nds32 implementation
of flush_dcache_page().
Link: https://lkml.kernel.org/r/20210330175126.26500-1-rppt@kernel.org
Fixes: cb9f753a3731 ("mm: fix races between swapoff and flush dcache")
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Acked-by: Greentime Hu <green.hu@gmail.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When we do coredump for user process signal, this may be an SIGBUS signal
with BUS_MCEERR_AR or BUS_MCEERR_AO code, which means this signal is
resulted from ECC memory fail like SRAR or SRAO, we expect the memory
recovery work is finished correctly, then the get_dump_page() will not
return the error page as its process pte is set invalid by
memory_failure().
But memory_failure() may fail, and the process's related pte may not be
correctly set invalid, for current code, we will return the poison page,
get it dumped, and then lead to system panic as its in kernel code.
So check the poison status in get_dump_page(), and if TRUE, return NULL.
There maybe other scenario that is also better to check the posion status
and not to panic, so make a wrapper for this check, Thanks to David's
suggestion(<david@redhat.com>).
[akpm@linux-foundation.org: s/0/false/]
[yaoaili@kingsoft.com: is_page_poisoned() arg cannot be null, per Matthew]
Link: https://lkml.kernel.org/r/20210322115233.05e4e82a@alex-virtual-machine
Link: https://lkml.kernel.org/r/20210319104437.6f30e80d@alex-virtual-machine
Signed-off-by: Aili Yao <yaoaili@kingsoft.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Naoya Horiguchi <naoya.horiguchi@nec.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Aili Yao <yaoaili@kingsoft.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Update Nick & Nadia's old addresses.
Link: https://lkml.kernel.org/r/20210406134036.GQ2531743@casper.infradead.org
Signed-off-by: Matthew Wilcox <willy@infradead.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Nadia Yvette Chambers <nyc@holomorphy.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
jcrouse at codeaurora.org has started bouncing. Redirect to a more
permanent address.
Link: https://lkml.kernel.org/r/20210325143700.1490518-1-jordan@cosmicpenguin.net
Signed-off-by: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: Alexander Lobakin <alobakin@pm.me>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Kees Cook <keescook@chromium.org>
Cc: Miguel Ojeda <ojeda@kernel.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Change my e-mail address to kabel@kernel.org, and fix my name in
non-code parts (add diacritical mark).
Link: https://lkml.kernel.org/r/20210325171123.28093-2-kabel@kernel.org
Signed-off-by: Marek Behún <kabel@kernel.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jassi Brar <jassisinghbrar@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add all the files maintained by Turris team, not only for MOX, but also
for Omnia. Change website.
Link: https://lkml.kernel.org/r/20210325171123.28093-1-kabel@kernel.org
Signed-off-by: Marek Behún <kabel@kernel.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Jassi Brar <jassisinghbrar@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|