| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
DSI PHY errors are falsely reported whenever a dsi error occurs. This is
because DSI_DLN0_PHY_ERR isn't only used as a status register, but also
used to mask PHY errors. Currently, we end up reading the mask bits too
and therefore always report errors.
Ignore the register mask bits and check for only the status/clear bits.
Signed-off-by: Archit Taneja <[email protected]>
Signed-off-by: Rob Clark <[email protected]>
|
|
The maximum output width of one pipeline depends on the LayerMixer's
capability. It may be different on each target. Also, MDP5 doesn't
have vertical limitation in one frame, as long as the pixel clock
can be supported.
This change obtains the maximum LM resolution from configuration
table and treat it as the whole pipe's limitation for MDP5. The size
limit on MDP4 is not changed.
Signed-off-by: Hai Li <[email protected]>
|
|
For all of these devices, msm89xy was the lead chip, so standardize the
compatible names to align with convention used by rest of the qcom/msm
drivers.
Signed-off-by: Rob Clark <[email protected]>
|
|
This change adds the MDP and HDMI support for msm8x94.
Note that HDMI PHY registers are not being accessed anymore from
the driver.
Signed-off-by: Stephane Viau <[email protected]>
[rename compatible s/8x94/8994/ since preference is to not trust the
marketing folks who invent chip #'s but instead name things after the
lead chip.. we should rename some 80XY to 89XY to standardize on the
lead chip but leave that for another patch. Also, update dt bindings
doc]
Signed-off-by: Rob Clark <[email protected]>
|
|
->reset() currently only accesses HDMI core registers, and yet it
is located in hdmi_phy*. Since no PHY registers are being
accessed during ->reset(), it would be better to bring that
function in hdmi core module where HDMI core registers are
usually being accessed.
This will also help for msm8x94 for which no PHY registers
accesses are done (->phy_init == NULL) but the HDMI PHY reset
from HDMI core still needs to be done.
Note:
SW_RESET_PLL bit is not written in hdmi_phy_8x60_reset(); this
write should not affect anything if the corresponding field is
not writable.
Signed-off-by: Stephane Viau <[email protected]>
[fixed warning about unused 'phy' in hpd_enable() while merging]
Signed-off-by: Rob Clark <[email protected]>
|
|
DSI controller on msm8x94 is version 1.3, which requires different
power supplies and works with 20nm DSI PHY. This change is to add
the basic support for this version.
Signed-off-by: Hai Li <[email protected]>
Signed-off-by: Rob Clark <[email protected]>
|
|
Some targets use pinctrl framework to configure some
pins. This change allows DSI driver to set default and
sleep pinctrl status.
Signed-off-by: Hai Li <[email protected]>
Signed-off-by: Rob Clark <[email protected]>
|
|
The current term of *dual panel* in DSI driver code causes confusion.
It is supposed to indicate the panel using two DSI links. Rename it
to *dual DSI*.
Signed-off-by: Hai Li <[email protected]>
Signed-off-by: Rob Clark <[email protected]>
|
|
The source PLL to be used by each DSI PHY should be decided by
DSI manager based on dual DSI information, while the register
programming to select PLL is different from one type of PHY to
another. This change adds the H/W difference to PHY configuration
and updates the interface between DSI manager and PHY.
With this change, PLL selection can be supported on different
targets.
Signed-off-by: Hai Li <[email protected]>
Signed-off-by: Rob Clark <[email protected]>
|
|
Add HDMI HDCP support including HDCP PartI/II/III authentication.
V1: Initial Change
V2: Address Bjorn&Rob's comments
Refactor the authentication process to use single work instead
of multiple work for different authentication stages.
V3: Update to align with qcom SCM api.
Signed-off-by: Jilai Wang <[email protected]>
Signed-off-by: Rob Clark <[email protected]>
|
|
Signed-off-by: Rob Clark <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This has two libfc fixes for bugs causing rare crashes, one iscsi fix
for a potential hang on shutdown, and a fix for an I/O blocksize issue
which caused a regression"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
sd: Fix maximum I/O size for BLOCK_PC requests
libfc: Fix fc_fcp_cleanup_each_cmd()
libfc: Fix fc_exch_recv_req() error path
libiscsi: Fix host busy blocking during connection teardown
|
|
Pull KVM fixes from Paolo Bonzini:
"Just two very small & simple patches"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: Use adjustment in guest cycles when handling MSR_IA32_TSC_ADJUST
KVM: x86: zero IDT limit on entry to SMM
|
|
Merge fixes from Andrew Morton:
"11 fixes"
* emailed patches from Andrew Morton <[email protected]>:
Update maintainers for DRM STI driver
mm: cma: mark cma_bitmap_maxno() inline in header
zram: fix pool name truncation
memory-hotplug: fix wrong edge when hot add a new node
.mailmap: Andrey Ryabinin has moved
ipc/sem.c: update/correct memory barriers
mm/hwpoison: fix panic due to split huge zero page
ipc,sem: remove uneeded sem_undo_list lock usage in exit_sem()
ipc,sem: fix use after free on IPC_RMID after a task using same semaphore set exits
mm/hwpoison: fix fail isolate hugetlbfs page w/ refcount held
mm/hwpoison: fix page refcount of unknown non LRU page
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clock fix from Stephen Boyd:
"A one-liner for a regression found in the PXA clock driver"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: pxa: pxa3xx: fix CKEN register access
|
|
Add Vincent Abriou and myself as maintainers.
Signed-off-by: Benjamin Gaignard <[email protected]>
Cc: Vincent Abriou <[email protected]>
Cc: Dave Airlie <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
cma_bitmap_maxno() was marked as static and not static inline, which can
cause warnings about this function not being used if this file is included
in a file that does not call that function, and violates the conventions
used elsewhere. The two options are to move the function implementation
back to mm/cma.c or make it inline here, and it's simple enough for the
latter to make sense.
Signed-off-by: Gregory Fong <[email protected]>
Cc: Joonsoo Kim <[email protected]>
Cc: Sasha Levin <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
zram_meta_alloc() constructs a pool name for zs_create_pool() call as
snprintf(pool_name, sizeof(pool_name), "zram%d", device_id);
However, it defines pool name buffer to be only 8 bytes long (minus
trailing zero), which means that we can have only 1000 pool names: zram0
-- zram999.
With CONFIG_ZSMALLOC_STAT enabled an attempt to create a device zram1000
can fail if device zram100 already exists, because snprintf() will
truncate new pool name to zram100 and pass it debugfs_create_dir(),
causing:
debugfs dir <zram100> creation failed
zram: Error creating memory pool
... and so on.
Fix it by passing zram->disk->disk_name to zram_meta_alloc() instead of
divice_id. We construct zram%d name earlier and keep it as a ->disk_name,
no need to snprintf() it again.
Signed-off-by: Sergey Senozhatsky <[email protected]>
Cc: Minchan Kim <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
When we add a new node, the edge of memory may be wrong.
e.g. system has 4 nodes, and node3 is movable, node3 mem:[24G-32G],
1. hotremove the node3,
2. then hotadd node3 with a part of memory, mem:[26G-30G],
3. call hotadd_new_pgdat()
free_area_init_node()
get_pfn_range_for_nid()
4. it will return wrong start_pfn and end_pfn, because we have not
update the memblock.
This patch also fixes a BUG_ON during hot-addition, please see
http://marc.info/?l=linux-kernel&m=142961156129456&w=2
Signed-off-by: Xishi Qiu <[email protected]>
Cc: Yasuaki Ishimatsu <[email protected]>
Cc: Kamezawa Hiroyuki <[email protected]>
Cc: Taku Izumi <[email protected]>
Cc: Tang Chen <[email protected]>
Cc: Gu Zheng <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Update my email address.
Signed-off-by: Andrey Ryabinin <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
sem_lock() did not properly pair memory barriers:
!spin_is_locked() and spin_unlock_wait() are both only control barriers.
The code needs an acquire barrier, otherwise the cpu might perform read
operations before the lock test.
As no primitive exists inside <include/spinlock.h> and since it seems
noone wants another primitive, the code creates a local primitive within
ipc/sem.c.
With regards to -stable:
The change of sem_wait_array() is a bugfix, the change to sem_lock() is a
nop (just a preprocessor redefinition to improve the readability). The
bugfix is necessary for all kernels that use sem_wait_array() (i.e.:
starting from 3.10).
Signed-off-by: Manfred Spraul <[email protected]>
Reported-by: Oleg Nesterov <[email protected]>
Acked-by: Peter Zijlstra (Intel) <[email protected]>
Cc: "Paul E. McKenney" <[email protected]>
Cc: Kirill Tkhai <[email protected]>
Cc: Ingo Molnar <[email protected]>
Cc: Josh Poimboeuf <[email protected]>
Cc: Davidlohr Bueso <[email protected]>
Cc: <[email protected]> [3.10+]
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Bug:
------------[ cut here ]------------
kernel BUG at mm/huge_memory.c:1957!
invalid opcode: 0000 [#1] SMP
Modules linked in: snd_hda_codec_hdmi i915 rpcsec_gss_krb5 snd_hda_codec_realtek snd_hda_codec_generic nfsv4 dns_re
CPU: 2 PID: 2576 Comm: test_huge Not tainted 4.2.0-rc5-mm1+ #27
Hardware name: Dell Inc. OptiPlex 7020/0F5C5X, BIOS A03 01/08/2015
task: ffff880204e3d600 ti: ffff8800db16c000 task.ti: ffff8800db16c000
RIP: split_huge_page_to_list+0xdb/0x120
Call Trace:
memory_failure+0x32e/0x7c0
madvise_hwpoison+0x8b/0x160
SyS_madvise+0x40/0x240
? do_page_fault+0x37/0x90
entry_SYSCALL_64_fastpath+0x12/0x71
Code: ff f0 41 ff 4c 24 30 74 0d 31 c0 48 83 c4 08 5b 41 5c 41 5d c9 c3 4c 89 e7 e8 e2 58 fd ff 48 83 c4 08 31 c0
RIP split_huge_page_to_list+0xdb/0x120
RSP <ffff8800db16fde8>
---[ end trace aee7ce0df8e44076 ]---
Testcase:
#define _GNU_SOURCE
#include <stdlib.h>
#include <stdio.h>
#include <sys/mman.h>
#include <unistd.h>
#include <fcntl.h>
#include <sys/types.h>
#include <errno.h>
#include <string.h>
#define MB 1024*1024
int main(void)
{
char *mem;
posix_memalign((void **)&mem, 2 * MB, 200 * MB);
madvise(mem, 200 * MB, MADV_HWPOISON);
free(mem);
return 0;
}
Huge zero page is allocated if page fault w/o FAULT_FLAG_WRITE flag.
The get_user_pages_fast() which called in madvise_hwpoison() will get
huge zero page if the page is not allocated before. Huge zero page is a
tranparent huge page, however, it is not an anonymous page.
memory_failure will split the huge zero page and trigger
BUG_ON(is_huge_zero_page(page));
After commit 98ed2b0052e6 ("mm/memory-failure: give up error handling
for non-tail-refcounted thp"), memory_failure will not catch non anon
thp from madvise_hwpoison path and this bug occur.
Fix it by catching non anon thp in memory_failure in order to not split
huge zero page in madvise_hwpoison path.
After this patch:
Injecting memory failure for page 0x202800 at 0x7fd8ae800000
MCE: 0x202800: non anonymous thp
[...]
[[email protected]: remove second split, per Wanpeng]
Signed-off-by: Wanpeng Li <[email protected]>
Acked-by: Naoya Horiguchi <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
After we acquire the sma->sem_perm lock in exit_sem(), we are protected
against a racing IPC_RMID operation. Also at that point, we are the last
user of sem_undo_list. Therefore it isn't required that we acquire or use
ulp->lock.
Signed-off-by: Herton R. Krzesinski <[email protected]>
Acked-by: Manfred Spraul <[email protected]>
Cc: Davidlohr Bueso <[email protected]>
Cc: Rafael Aquini <[email protected]>
CC: Aristeu Rozanski <[email protected]>
Cc: David Jeffery <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
set exits
The current semaphore code allows a potential use after free: in
exit_sem we may free the task's sem_undo_list while there is still
another task looping through the same semaphore set and cleaning the
sem_undo list at freeary function (the task called IPC_RMID for the same
semaphore set).
For example, with a test program [1] running which keeps forking a lot
of processes (which then do a semop call with SEM_UNDO flag), and with
the parent right after removing the semaphore set with IPC_RMID, and a
kernel built with CONFIG_SLAB, CONFIG_SLAB_DEBUG and
CONFIG_DEBUG_SPINLOCK, you can easily see something like the following
in the kernel log:
Slab corruption (Not tainted): kmalloc-64 start=ffff88003b45c1c0, len=64
000: 6b 6b 6b 6b 6b 6b 6b 6b 00 6b 6b 6b 6b 6b 6b 6b kkkkkkkk.kkkkkkk
010: ff ff ff ff 6b 6b 6b 6b ff ff ff ff ff ff ff ff ....kkkk........
Prev obj: start=ffff88003b45c180, len=64
000: 00 00 00 00 ad 4e ad de ff ff ff ff 5a 5a 5a 5a .....N......ZZZZ
010: ff ff ff ff ff ff ff ff c0 fb 01 37 00 88 ff ff ...........7....
Next obj: start=ffff88003b45c200, len=64
000: 00 00 00 00 ad 4e ad de ff ff ff ff 5a 5a 5a 5a .....N......ZZZZ
010: ff ff ff ff ff ff ff ff 68 29 a7 3c 00 88 ff ff ........h).<....
BUG: spinlock wrong CPU on CPU#2, test/18028
general protection fault: 0000 [#1] SMP
Modules linked in: 8021q mrp garp stp llc nf_conntrack_ipv4 nf_defrag_ipv4 ip6t_REJECT nf_reject_ipv6 nf_conntrack_ipv6 nf_defrag_ipv6 xt_state nf_conntrack ip6table_filter ip6_tables binfmt_misc ppdev input_leds joydev parport_pc parport floppy serio_raw virtio_balloon virtio_rng virtio_console virtio_net iosf_mbi crct10dif_pclmul crc32_pclmul ghash_clmulni_intel pcspkr qxl ttm drm_kms_helper drm snd_hda_codec_generic i2c_piix4 snd_hda_intel snd_hda_codec snd_hda_core snd_hwdep snd_seq snd_seq_device snd_pcm snd_timer snd soundcore crc32c_intel virtio_pci virtio_ring virtio pata_acpi ata_generic [last unloaded: speedstep_lib]
CPU: 2 PID: 18028 Comm: test Not tainted 4.2.0-rc5+ #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.8.1-20150318_183358- 04/01/2014
RIP: spin_dump+0x53/0xc0
Call Trace:
spin_bug+0x30/0x40
do_raw_spin_unlock+0x71/0xa0
_raw_spin_unlock+0xe/0x10
freeary+0x82/0x2a0
? _raw_spin_lock+0xe/0x10
semctl_down.clone.0+0xce/0x160
? __do_page_fault+0x19a/0x430
? __audit_syscall_entry+0xa8/0x100
SyS_semctl+0x236/0x2c0
? syscall_trace_leave+0xde/0x130
entry_SYSCALL_64_fastpath+0x12/0x71
Code: 8b 80 88 03 00 00 48 8d 88 60 05 00 00 48 c7 c7 a0 2c a4 81 31 c0 65 8b 15 eb 40 f3 7e e8 08 31 68 00 4d 85 e4 44 8b 4b 08 74 5e <45> 8b 84 24 88 03 00 00 49 8d 8c 24 60 05 00 00 8b 53 04 48 89
RIP [<ffffffff810d6053>] spin_dump+0x53/0xc0
RSP <ffff88003750fd68>
---[ end trace 783ebb76612867a0 ]---
NMI watchdog: BUG: soft lockup - CPU#3 stuck for 22s! [test:18053]
Modules linked in: 8021q mrp garp stp llc nf_conntrack_ipv4 nf_defrag_ipv4 ip6t_REJECT nf_reject_ipv6 nf_conntrack_ipv6 nf_defrag_ipv6 xt_state nf_conntrack ip6table_filter ip6_tables binfmt_misc ppdev input_leds joydev parport_pc parport floppy serio_raw virtio_balloon virtio_rng virtio_console virtio_net iosf_mbi crct10dif_pclmul crc32_pclmul ghash_clmulni_intel pcspkr qxl ttm drm_kms_helper drm snd_hda_codec_generic i2c_piix4 snd_hda_intel snd_hda_codec snd_hda_core snd_hwdep snd_seq snd_seq_device snd_pcm snd_timer snd soundcore crc32c_intel virtio_pci virtio_ring virtio pata_acpi ata_generic [last unloaded: speedstep_lib]
CPU: 3 PID: 18053 Comm: test Tainted: G D 4.2.0-rc5+ #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.8.1-20150318_183358- 04/01/2014
RIP: native_read_tsc+0x0/0x20
Call Trace:
? delay_tsc+0x40/0x70
__delay+0xf/0x20
do_raw_spin_lock+0x96/0x140
_raw_spin_lock+0xe/0x10
sem_lock_and_putref+0x11/0x70
SYSC_semtimedop+0x7bf/0x960
? handle_mm_fault+0xbf6/0x1880
? dequeue_task_fair+0x79/0x4a0
? __do_page_fault+0x19a/0x430
? kfree_debugcheck+0x16/0x40
? __do_page_fault+0x19a/0x430
? __audit_syscall_entry+0xa8/0x100
? do_audit_syscall_entry+0x66/0x70
? syscall_trace_enter_phase1+0x139/0x160
SyS_semtimedop+0xe/0x10
SyS_semop+0x10/0x20
entry_SYSCALL_64_fastpath+0x12/0x71
Code: 47 10 83 e8 01 85 c0 89 47 10 75 08 65 48 89 3d 1f 74 ff 7e c9 c3 0f 1f 44 00 00 55 48 89 e5 e8 87 17 04 00 66 90 c9 c3 0f 1f 00 <55> 48 89 e5 0f 31 89 c1 48 89 d0 48 c1 e0 20 89 c9 48 09 c8 c9
Kernel panic - not syncing: softlockup: hung tasks
I wasn't able to trigger any badness on a recent kernel without the
proper config debugs enabled, however I have softlockup reports on some
kernel versions, in the semaphore code, which are similar as above (the
scenario is seen on some servers running IBM DB2 which uses semaphore
syscalls).
The patch here fixes the race against freeary, by acquiring or waiting
on the sem_undo_list lock as necessary (exit_sem can race with freeary,
while freeary sets un->semid to -1 and removes the same sem_undo from
list_proc or when it removes the last sem_undo).
After the patch I'm unable to reproduce the problem using the test case
[1].
[1] Test case used below:
#include <stdio.h>
#include <sys/types.h>
#include <sys/ipc.h>
#include <sys/sem.h>
#include <sys/wait.h>
#include <stdlib.h>
#include <time.h>
#include <unistd.h>
#include <errno.h>
#define NSEM 1
#define NSET 5
int sid[NSET];
void thread()
{
struct sembuf op;
int s;
uid_t pid = getuid();
s = rand() % NSET;
op.sem_num = pid % NSEM;
op.sem_op = 1;
op.sem_flg = SEM_UNDO;
semop(sid[s], &op, 1);
exit(EXIT_SUCCESS);
}
void create_set()
{
int i, j;
pid_t p;
union {
int val;
struct semid_ds *buf;
unsigned short int *array;
struct seminfo *__buf;
} un;
/* Create and initialize semaphore set */
for (i = 0; i < NSET; i++) {
sid[i] = semget(IPC_PRIVATE , NSEM, 0644 | IPC_CREAT);
if (sid[i] < 0) {
perror("semget");
exit(EXIT_FAILURE);
}
}
un.val = 0;
for (i = 0; i < NSET; i++) {
for (j = 0; j < NSEM; j++) {
if (semctl(sid[i], j, SETVAL, un) < 0)
perror("semctl");
}
}
/* Launch threads that operate on semaphore set */
for (i = 0; i < NSEM * NSET * NSET; i++) {
p = fork();
if (p < 0)
perror("fork");
if (p == 0)
thread();
}
/* Free semaphore set */
for (i = 0; i < NSET; i++) {
if (semctl(sid[i], NSEM, IPC_RMID))
perror("IPC_RMID");
}
/* Wait for forked processes to exit */
while (wait(NULL)) {
if (errno == ECHILD)
break;
};
}
int main(int argc, char **argv)
{
pid_t p;
srand(time(NULL));
while (1) {
p = fork();
if (p < 0) {
perror("fork");
exit(EXIT_FAILURE);
}
if (p == 0) {
create_set();
goto end;
}
/* Wait for forked processes to exit */
while (wait(NULL)) {
if (errno == ECHILD)
break;
};
}
end:
return 0;
}
[[email protected]: use normal comment layout]
Signed-off-by: Herton R. Krzesinski <[email protected]>
Acked-by: Manfred Spraul <[email protected]>
Cc: Davidlohr Bueso <[email protected]>
Cc: Rafael Aquini <[email protected]>
CC: Aristeu Rozanski <[email protected]>
Cc: David Jeffery <[email protected]>
Cc: <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Hugetlbfs pages will get a refcount in get_any_page() or
madvise_hwpoison() if soft offlining through madvise. The refcount which
is held by the soft offline path should be released if we fail to isolate
hugetlbfs pages.
Fix it by reducing the refcount for both isolation success and failure.
Signed-off-by: Wanpeng Li <[email protected]>
Acked-by: Naoya Horiguchi <[email protected]>
Cc: <[email protected]> [3.9+]
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
After trying to drain pages from pagevec/pageset, we try to get reference
count of the page again, however, the reference count of the page is not
reduced if the page is still not on LRU list.
Fix it by adding the put_page() to drop the page reference which is from
__get_any_page().
Signed-off-by: Wanpeng Li <[email protected]>
Acked-by: Naoya Horiguchi <[email protected]>
Cc: <[email protected]> [3.9+]
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Release all blocks after the pipe is disabled, even when vsync
didn't happen in some error cases. Allow requesting SMB multiple
times before configuring to hardware, by releasing blocks not
programmed to hardware yet for shrinking case.
This fixes a potential leak of shared memory pool blocks.
Signed-off-by: Wentao Xu <[email protected]>
Tested-by: Archit Taneja <[email protected]>
Signed-off-by: Rob Clark <[email protected]>
|
|
The atomic commit cannot easily undo and return an error once the
state is swapped. Change to uninterruptible wait, and ignore the
timeout error.
Signed-off-by: Wentao Xu <[email protected]>
Signed-off-by: Rob Clark <[email protected]>
|
|
mdp4_get_frame_format() can dereference a drm_framebuffer when it's NULL.
Call it in mdp4_plane_mode_set only when we know fb is non-NULL.
Signed-off-by: Archit Taneja <[email protected]>
Signed-off-by: Rob Clark <[email protected]>
|
|
We need to return a new sgt, since the caller takes ownership of it.
Reported-by: Stanimir Varbanov <[email protected]>
Signed-off-by: Rob Clark <[email protected]>
|
|
Put the Kconfig entries for bridge drivers into a separate menu so that
they are automatically grouped and don't clutter up the top-level menu.
While at it, move the bridge menu towards the end of the top-level menu
where the panel menu is already located.
Signed-off-by: Thierry Reding <[email protected]>
|
|
The LG4573 is used on the LG LCD LB043WV2-SD01, an industrial 4.3" TFT
panel with SPI control interface.
Signed-off-by: Heiko Schocher <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
|
|
Add support for the Okaya RS800480T-7X0GP to the DRM simple panel
driver.
The RS800480T-7X0GP is a WVGA (800x480) panel with an 18-bit parallel
LCD interface. It supports pixel clocks in the range of 30-40 MHz.
This panel details can be found at:
http://boundarydevices.com/product/7-800x480-display/
Signed-off-by: Gary Bisson <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
|
|
This patch adds vendor prefix for Okaya Electronic America, a provider
of LCD modules and display technologies.
Signed-off-by: Gary Bisson <[email protected]>
Acked-by: Rob Herring <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
|
|
This adds support for the NEC NL4827HC19-05B 480x272 panel to the DRM
simple panel driver.
Signed-off-by: Alison Wang <[email protected]>
Signed-off-by: Xiubo Li <[email protected]>
Signed-off-by: Jianwei Wang <[email protected]>
Acked-by: Daniel Vetter <[email protected]>
[[email protected]: add .bpc field for panel]
Signed-off-by: Thierry Reding <[email protected]>
|
|
The AUO B080UAN01 is an 8.0" WUXGA TFT LCD panel connected using four
DSI lanes. It can be supported by the simple-panel driver.
Signed-off-by: Thierry Reding <[email protected]>
|
|
According to the data sheet, the minimum horizontal blanking interval
is 54 clocks (1 + 52 + 1), but tests with a Nitrogen6X have shown the
minimum working horizontal blanking interval to be 60 clocks.
Signed-off-by: Philipp Zabel <[email protected]>
Signed-off-by: Lucas Stach <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
|
|
The bus format both specifies the bpc and the way the individual bits get
serialized into the 7 LVDS timeslots.
While the is only one standard mapping for 6 bpc and so the driver could
infer the bit mapping from the bpc alone, there are more options for the
8 bpc case which makes specifiying the bus format mandatory.
To keep things consistent across panels and to set a precedent for new
panel additions add the proper bus format.
Signed-off-by: Philipp Zabel <[email protected]>
Signed-off-by: Lucas Stach <[email protected]>
Signed-off-by: Thierry Reding <[email protected]>
|
|
Use vendor prefixes for Kconfig symbols and filenames. This should make
it easier to identify the various bridge drivers and to organize the
directory.
v2: fix object name for dw-hdmi (Fabio Estevam)
Signed-off-by: Thierry Reding <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fix from Ingo Molnar:
"A single clocksource driver suspend/resume fix"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clockevents/drivers/sh_cmt: Only perform clocksource suspend/resume if enabled
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Misc fixes: PMU driver corner cases, tooling fixes, and an 'AUX'
(Intel PT) race related core fix"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel/cqm: Do not access cpu_data() from CPU_UP_PREPARE handler
perf/x86/intel: Fix memory leak on hot-plug allocation fail
perf: Fix PERF_EVENT_IOC_PERIOD migration race
perf: Fix double-free of the AUX buffer
perf: Fix fasync handling on inherited events
perf tools: Fix test build error when bindir contains double slash
perf stat: Fix transaction lenght metrics
perf: Fix running time accounting
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fix from Ingo Molnar:
"A single fix for a locking self-test crash"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/pvqspinlock: Fix kernel panic in locking-selftest
|
|
Pull drm fixes from Dave Airlie:
"Back from holidays, found these in the cracks: one nouveau revert, one
vmwgfx locking fix and a bunch of exynos fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
Revert "drm/nouveau/fifo/gk104: kick channels when deactivating them"
drm/vmwgfx: Fix execbuf locking issues
drm/exynos/fimc: fix runtime pm support
drm/exynos/mixer: always update INT_EN cache
drm/exynos/mixer: correct vsync configuration sequence
drm/exynos/mixer: fix interrupt clearing
drm/exynos/hdmi: fix edid memory leak
drm/exynos: gsc: fix wrong bitwise operation for swap detection
|
|
An OEM may request increased I_boost beyond the recommended values
by specifying an I_boost value to be applied to all swing entries for
a port. These override values are specified in VBT.
v2: rebase and remove unused iboost_bit variable
Issue: VIZ-5676
Signed-off-by: Antti Koskipaa <[email protected]>
Reviewed-by: David Weinehall <[email protected]>
Signed-off-by: Daniel Vetter <[email protected]>
|
|
Backmerge drm-intel-fixes because a bunch of atomic patch backporting
we had to do lead to horrible conflicts.
Conflicts:
drivers/gpu/drm/drm_crtc.c
Just a bit of context conflict between -next and -fixes.
drivers/gpu/drm/i915/intel_atomic.c
drivers/gpu/drm/i915/intel_display.c
Atomic conflicts, always pick the code from -next.
Signed-off-by: Daniel Vetter <[email protected]>
|
|
There is currently conflicting documentation on which steppings the
workaround is needed, up to C vs. forever. However there is post-C
stepping hardware that doesn't report port presence on DDI A, leading to
black screen on eDP. Assume the strap isn't connected, and try to enable
DDI A on these machines. (We'll still check the VBT for the info in DDI
init.)
Cc: Ville Syrjälä <[email protected]>
Cc: Mika Westerberg <[email protected]>
Signed-off-by: Jani Nikula <[email protected]>
Signed-off-by: Daniel Vetter <[email protected]>
|
|
DP spec requires the checksum of the last block read to be written
when replying to TEST_EDID_READ. This patch fixes the current code
to do the same.
v2: removed loop for jumping blocks and performed direct addition
as recommended by Daniel
Signed-off-by: Sivakumar Thulasimani <[email protected]>
Reviewed-by: Sonika Jindal <[email protected]>
Signed-off-by: Daniel Vetter <[email protected]>
|
|
Prevent leaking the if scoping by containing the WA_REG
macro inside its own scope.
Reported-by: Arun Siluvery <[email protected]>
Signed-off-by: Mika Kuoppala <[email protected]>
Reviewed-by: Dave Gordon <[email protected]>
[danvet: Appease checkpatch.]
Signed-off-by: Daniel Vetter <[email protected]>
|
|
If we encounter an allocation failure during ppggt creation (trivial
even with 16Gib+ RAM!), we need to remove the dead context from the
fpriv->context_idr along with the references.
gem_exec_ctx: page allocation failure: order:0, mode:0x8004
CPU: 3 PID: 27272 Comm: gem_exec_ctx Tainted: G W 4.2.0-rc5+ #37
0000000000000000 ffff880086ff7a78 ffffffff816b947a ffff88041ed90038
0000000000008004 ffff880086ff7b08 ffffffff8114b1a5 ffff880086ff7ac8
ffffffff8108d848 0000000000000000 ffffffff81ce84b8 0000000000000000
Call Trace:
[<ffffffff816b947a>] dump_stack+0x45/0x57
[<ffffffff8114b1a5>] warn_alloc_failed+0xd5/0x120
[<ffffffff8108d848>] ? __wake_up+0x48/0x60
[<ffffffff8114e0ed>] __alloc_pages_nodemask+0x73d/0x8e0
[<ffffffffc0472238>] ? i915_gem_execbuffer2+0x148/0x240 [i915]
[<ffffffffc0474240>] __setup_page_dma+0x30/0x110 [i915]
[<ffffffffc0477f61>] gen8_ppgtt_init+0x31/0x2f0 [i915]
[<ffffffffc04785e0>] i915_ppgtt_init+0x30/0x80 [i915]
[<ffffffffc0478928>] i915_ppgtt_create+0x48/0xc0 [i915]
[<ffffffffc046c9c2>] i915_gem_create_context+0x1c2/0x390 [i915]
[<ffffffffc046d9cb>] i915_gem_context_create_ioctl+0x5b/0xa0 [i915]
leading to an oops in i915_gem_context_close. Also note that this
benchmark should not be running out of memory in the first place...
Testcase: igt/benchmark/gem_exec_ctx -b create # ppgtt >= 2
Signed-off-by: Chris Wilson <[email protected]>
Reviewed-by: Mika Kuoppala <[email protected]>
Signed-off-by: Daniel Vetter <[email protected]>
|
|
The IOMMU for Intel graphics has historically had many issues resulting
in random GPU hangs. Lets include its status when capturing the GPU hang
error state for post-mortem analysis.
Signed-off-by: Chris Wilson <[email protected]>
Signed-off-by: Daniel Vetter <[email protected]>
|