| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Fixes: 49aa7830396b ("bcachefs: Fix rebalance_work accounting")
Signed-off-by: Kent Overstreet <[email protected]>
|
|
Matt Johnston says:
====================
net: mctp-serial: Fix for missing tx escapes
The mctp-serial code to add escape characters was incorrect due to an
off-by-one error. This series adds a test for the chunking which splits
by escape characters, and fixes the bug.
v2: Fix kunit param const pointer
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
0x7d and 0x7e bytes are meant to be escaped in the data portion of
frames, but this didn't occur since next_chunk_len() had an off-by-one
error. That also resulted in the final byte of a payload being written
as a separate tty write op.
The chunk prior to an escaped byte would be one byte short, and the
next call would never test the txpos+1 case, which is where the escaped
byte was located. That meant it never hit the escaping case in
mctp_serial_tx_work().
Example Input: 01 00 08 c8 7e 80 02
Previous incorrect chunks from next_chunk_len():
01 00 08
c8 7e 80
02
With this fix:
01 00 08 c8
7e
80 02
Cc: [email protected]
Fixes: a0c2ccd9b5ad ("mctp: Add MCTP-over-serial transport binding")
Signed-off-by: Matt Johnston <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Test various edge cases of inputs that contain characters
that need escaping.
This adds a new kunit suite for mctp-serial.
Signed-off-by: Matt Johnston <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
In the LTC2991, V5 and V6 channels use the low nibble of the
"V5, V6, V7, and V8 Control Register" for configuration, but currently,
the high nibble is defined.
This patch changes the defines to use the low nibble.
Fixes: 2b9ea4262ae9 ("hwmon: Add driver for ltc2991")
Signed-off-by: Pawel Dembicki <[email protected]>
Message-ID: <[email protected]>
Signed-off-by: Guenter Roeck <[email protected]>
|
|
The fscache_cookie_lru_timer is initialized when the fscache module
is inserted, but is not deleted when the fscache module is removed.
If timer_reduce() is called before removing the fscache module,
the fscache_cookie_lru_timer will be added to the timer list of
the current cpu. Afterwards, a use-after-free will be triggered
in the softIRQ after removing the fscache module, as follows:
==================================================================
BUG: unable to handle page fault for address: fffffbfff803c9e9
PF: supervisor read access in kernel mode
PF: error_code(0x0000) - not-present page
PGD 21ffea067 P4D 21ffea067 PUD 21ffe6067 PMD 110a7c067 PTE 0
Oops: Oops: 0000 [#1] PREEMPT SMP KASAN PTI
CPU: 1 UID: 0 PID: 0 Comm: swapper/1 Tainted: G W 6.11.0-rc3 #855
Tainted: [W]=WARN
RIP: 0010:__run_timer_base.part.0+0x254/0x8a0
Call Trace:
<IRQ>
tmigr_handle_remote_up+0x627/0x810
__walk_groups.isra.0+0x47/0x140
tmigr_handle_remote+0x1fa/0x2f0
handle_softirqs+0x180/0x590
irq_exit_rcu+0x84/0xb0
sysvec_apic_timer_interrupt+0x6e/0x90
</IRQ>
<TASK>
asm_sysvec_apic_timer_interrupt+0x1a/0x20
RIP: 0010:default_idle+0xf/0x20
default_idle_call+0x38/0x60
do_idle+0x2b5/0x300
cpu_startup_entry+0x54/0x60
start_secondary+0x20d/0x280
common_startup_64+0x13e/0x148
</TASK>
Modules linked in: [last unloaded: netfs]
==================================================================
Therefore delete fscache_cookie_lru_timer when removing the fscahe module.
Fixes: 12bb21a29c19 ("fscache: Implement cookie user counting and resource pinning")
Cc: [email protected]
Signed-off-by: Baokun Li <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Acked-by: David Howells <[email protected]>
Signed-off-by: Christian Brauner <[email protected]>
|
|
|
|
Pull smb client fixes from Steve French:
- copy_file_range fix
- two read fixes including read past end of file rc fix and read retry
crediting fix
- falloc zero range fix
* tag 'v6.11-rc5-smb-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Fix FALLOC_FL_ZERO_RANGE to preflush buffered part of target region
cifs: Fix copy offload to flush destination region
netfs, cifs: Fix handling of short DIO read
cifs: Fix lack of credit renegotiation on read retry
|
|
Push bcachefs fixes from Kent Overstreet:
"The data corruption in the buffered write path is troubling; inode
lock should not have been able to cause that...
- Fix a rare data corruption in the rebalance path, caught as a nonce
inconsistency on encrypted filesystems
- Revert lockless buffered write path
- Mark more errors as autofix"
* tag 'bcachefs-2024-08-21' of https://github.com/koverstreet/bcachefs:
bcachefs: Mark more errors as autofix
bcachefs: Revert lockless buffered IO path
bcachefs: Fix bch2_extents_match() false positive
bcachefs: Fix failure to return error in data_update_index_update()
|
|
raw_copy_{to,from}_user() do not call access_ok(), so this code allowed
userspace to access any virtual memory address.
Cc: [email protected]
Fixes: 7c83232161f6 ("riscv: add support for misaligned trap handling in S-mode")
Fixes: 441381506ba7 ("riscv: misaligned: remove CONFIG_RISCV_M_MODE specific code")
Signed-off-by: Samuel Holland <[email protected]>
Reviewed-by: Alexandre Ghiti <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Palmer Dabbelt <[email protected]>
|
|
errors that are known to always be safe to fix should be autofix: this
should be most errors even at this point, but that will need some
thorough review.
note that errors are still logged in the superblock, so we'll still know
that they happened.
Signed-off-by: Kent Overstreet <[email protected]>
|
|
We had a report of data corruption on nixos when building installer
images.
https://github.com/NixOS/nixpkgs/pull/321055#issuecomment-2184131334
It seems that writes are being dropped, but only when issued by QEMU,
and possibly only in snapshot mode. It's undetermined if it's write
calls are being dropped or dirty folios.
Further testing, via minimizing the original patch to just the change
that skips the inode lock on non appends/truncates, reveals that it
really is just not taking the inode lock that causes the corruption: it
has nothing to do with the other logic changes for preserving write
atomicity in corner cases.
It's also kernel config dependent: it doesn't reproduce with the minimal
kernel config that ktest uses, but it does reproduce with nixos's distro
config. Bisection the kernel config initially pointer the finger at page
migration or compaction, but it appears that was erroneous; we haven't
yet determined what kernel config option actually triggers it.
Sadly it appears this will have to be reverted since we're getting too
close to release and my plate is full, but we'd _really_ like to fully
debug it.
My suspicion is that this patch is exposing a preexisting bug - the
inode lock actually covers very little in IO paths, and we have a
different lock (the pagecache add lock) that guards against races with
truncate here.
Fixes: 7e64c86cdc6c ("bcachefs: Buffered write path now can avoid the inode lock")
Signed-off-by: Kent Overstreet <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull misc fixes from Guenter Roeck.
These are fixes for regressions that Guenther has been reporting, and
the maintainers haven't picked up and sent in. With rc6 fairly imminent,
I'm taking them directly from Guenter.
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
apparmor: fix policy_unpack_test on big endian systems
Revert "MIPS: csrc-r4k: Apply verification clocksource flags"
microblaze: don't treat zero reserved memory regions as error
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull power sequencing fix from Bartosz Golaszewski:
"A follow-up fix for the power sequencing subsystem. It turned out the
previous fix for this driver was incomplete and broke the WLAN support
on some platforms. This addresses the issue.
- set the direction of the wlan-enable GPIO to output after
requesting it as-is"
* tag 'pwrseq-fixes-for-v6.11-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
power: sequencing: qcom-wcn: set the wlan-enable GPIO to output
|
|
Commit a9aaf1ff88a8 ("power: sequencing: request the WLAN enable GPIO
as-is") broke WLAN on boards on which the wlan-enable GPIO enabling the
wifi module isn't in output mode by default. We need to set direction to
output while retaining the value that was already set to keep the ath
module on if it's already started.
Fixes: a9aaf1ff88a8 ("power: sequencing: request the WLAN enable GPIO as-is")
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Bartosz Golaszewski <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB fixes for 6.11-rc6. Included in here are:
- dwc3 driver fixes for reported issues
- MAINTAINER file update, marking a driver as unsupported :(
- cdnsp driver fixes
- USB gadget driver fix
- USB sysfs fix
- other tiny fixes
- new device ids for usb serial driver
All of these have been in linux-next this week with no reported
issues"
* tag 'usb-6.11-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: serial: option: add MeiG Smart SRM825L
usb: cdnsp: fix for Link TRB with TC
usb: dwc3: st: add missing depopulate in probe error path
usb: dwc3: st: fix probed platform device ref count on probe error path
usb: dwc3: ep0: Don't reset resource alloc flag (including ep0)
usb: core: sysfs: Unmerge @usb3_hardware_lpm_attr_group in remove_power_attributes()
usb: typec: fsa4480: Relax CHIP_ID check
usb: dwc3: xilinx: add missing depopulate in probe error path
usb: dwc3: omap: add missing depopulate in probe error path
dt-bindings: usb: microchip,usb2514: Fix reference USB device schema
usb: gadget: uvc: queue pump work in uvcg_video_enable()
cdc-acm: Add DISABLE_ECHO quirk for GE HealthCare UI Controller
usb: cdnsp: fix incorrect index in cdnsp_get_hw_deq function
usb: dwc3: core: Prevent USB core invalid event buffer address access
MAINTAINERS: Mark UVC gadget driver as orphan
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Minor fixes only.
The sd.c one ignores a sync cache request if format is in progress
which can happen if formatting a drive across suspend/resume"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: sd: Ignore command SYNCHRONIZE CACHE error if format in progress
scsi: aacraid: Fix double-free on probe failure
scsi: lpfc: Fix overflow build issue
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux
Pull nfsd fix from Chuck Lever:
- One more write delegation fix
* tag 'nfsd-6.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux:
nfsd: fix nfsd4_deleg_getattr_conflict in presence of third party lease
|
|
Pull xfs fixes from Chandan Babu:
- Do not call out v1 inodes with non-zero di_nlink field as being
corrupt
- Change xfs_finobt_count_blocks() to count "free inode btree" blocks
rather than "inode btree" blocks
- Don't report the number of trimmed bytes via FITRIM because the
underlying storage isn't required to do anything and failed discard
IOs aren't reported to the caller anyway
- Fix incorrect setting of rm_owner field in an rmap query
- Report missing disk offset range in an fsmap query
- Obtain m_growlock when extending realtime section of the filesystem
- Reset rootdir extent size hint after extending realtime section of
the filesystem
* tag 'xfs-6.11-fixes-4' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: reset rootdir extent size hint after growfsrt
xfs: take m_growlock when running growfsrt
xfs: Fix missing interval for missing_owner in xfs fsmap
xfs: use XFS_BUF_DADDR_NULL for daddrs in getfsmap code
xfs: Fix the owner setting issue for rmap query in xfs fsmap
xfs: don't bother reporting blocks trimmed via FITRIM
xfs: xfs_finobt_count_blocks() walks the wrong btree
xfs: fix folio dirtying for XFILE_ALLOC callers
xfs: fix di_onlink checking for V1/V2 inodes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"There is a fairly large number of bug fixes for Qualcomm platforms,
most of them addressing issues with the devicetree files for the newly
added Snapdragon X1 based laptops to make them more reliable.
The Qualcomm driver changes address a few build-time issues as well as
runtime problems in the tzmem and scm firmware, the USB Type-C driver,
and the cmd-db and pmic_glink soc drivers.
The NXP i.MX usually gets a bunch of devicetree fixes that is
proportional to the number of supported machines. This includes both
warning fixes and correctness for the 64-bit i.MX9, i.MX8 and
layerscape platforms, as well as a single fix for a 32-bit i.MX6 based
board.
The other changes are the usual minor changes, including an update to
the MAINTAINERS file, an omap3 dts file and a SoC driver for mpfs
(risc-v)"
* tag 'arm-fixes-6.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (50 commits)
firmware: microchip: fix incorrect error report of programming:timeout on success
soc: qcom: pd-mapper: Fix singleton refcount
firmware: qcom: tzmem: disable sdm670 platform
soc: qcom: pmic_glink: Actually communicate when remote goes down
usb: typec: ucsi: Move unregister out of atomic section
soc: qcom: pmic_glink: Fix race during initialization
firmware: qcom: qseecom: remove unused functions
firmware: qcom: tzmem: fix virtual-to-physical address conversion
firmware: qcom: scm: Mark get_wq_ctx() as atomic call
arm64: dts: qcom: x1e80100: Fix Adreno SMMU global interrupt
arm64: dts: qcom: disable GPU on x1e80100 by default
arm64: dts: imx8mm-phygate: fix typo pinctrcl-0
arm64: dts: imx95: correct L3Cache cache-sets
arm64: dts: imx95: correct a55 power-domains
arm64: dts: freescale: imx93-tqma9352-mba93xxla: fix typo
arm64: dts: freescale: imx93-tqma9352: fix CMA alloc-ranges
ARM: dts: imx6dl-yapp43: Increase LED current to match the yapp4 HW design
arm64: dts: imx93: update default value for snps,clk-csr
arm64: dts: freescale: tqma9352: Fix watchdog reset
arm64: dts: imx8mp-beacon-kit: Fix Stereo Audio on WM8962
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fix from Dmitry Torokhov:
- a fix for Cypress PS/2 touchpad for regression introduced in 6.11
merge window where a timeout condition is incorrectly reported for
all extended Cypress commands
* tag 'input-for-v6.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: cypress_ps2 - fix waiting for command response
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci fixes from Bjorn Helgaas:
- Add Manivannan Sadhasivam as PCI native host bridge and endpoint
driver reviewer (Manivannan Sadhasivam)
- Disable MHI RAM data parity error interrupt for qcom SA8775P SoC to
work around hardware erratum that causes a constant stream of
interrupts (Manivannan Sadhasivam)
- Don't try to fall back to qcom Operating Performance Points (OPP)
support unless the platform actually supports OPP (Manivannan
Sadhasivam)
- Add [email protected] mailing list to MAINTAINERS for NXP
layerscape and imx6 PCI controller drivers (Frank Li)
* tag 'pci-v6.11-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
MAINTAINERS: PCI: Add NXP PCI controller mailing list [email protected]
PCI: qcom: Use OPP only if the platform supports it
PCI: qcom-ep: Disable MHI RAM data parity error interrupt for SA8775P SoC
MAINTAINERS: Add Manivannan Sadhasivam as Reviewer for PCI native host bridge and endpoint drivers
|
|
Pull block fix from Jens Axboe:
"Fix for a single regression for WRITE_SAME introduced in the 6.11
merge window"
* tag 'block-6.11-20240830' of git://git.kernel.dk/linux:
block: fix detection of unsupported WRITE SAME in blkdev_issue_write_zeroes
|
|
Pull io_uring fixes from Jens Axboe:
- A fix for a regression that happened in 6.11 merge window, where the
copying of iovecs for compat mode applications got broken for certain
cases.
- Fix for a bug introduced in 6.10, where if using recv/send bundles
with classic provided buffers, the recv/send would fail to set the
right iovec count. This caused 0 byte send/recv results. Found via
code coverage testing and writing a test case to exercise it.
* tag 'io_uring-6.11-20240830' of git://git.kernel.dk/linux:
io_uring/kbuf: return correct iovec count from classic buffer peek
io_uring/rsrc: ensure compat iovecs are copied correctly
|
|
This aligns with what open gpu does, the 0x15 hex is just to trick you.
Fixes: 176fdcbddfd2 ("drm/nouveau/gsp/r535: add support for booting GSP-RM")
Reviewed-by: Ben Skeggs <[email protected]>
Signed-off-by: Dave Airlie <[email protected]>
Signed-off-by: Danilo Krummrich <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Due to 59b047bc98084f8af2c41483e4d68a5adf2fa7f7 there could be keys stored
with the wrong address type so this attempt to detect it and ignore them
instead of just failing to load all keys.
Cc: [email protected]
Link: https://github.com/bluez/bluez/issues/875
Fixes: 59b047bc9808 ("Bluetooth: MGMT/SMP: Fix address type when using SMP over BREDR/LE")
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
This reverts commit 59b047bc98084f8af2c41483e4d68a5adf2fa7f7 which
breaks compatibility with commands like:
bluetoothd[46328]: @ MGMT Command: Load.. (0x0013) plen 74 {0x0001} [hci0]
Keys: 2
BR/EDR Address: C0:DC:DA:A5:E5:47 (Samsung Electronics Co.,Ltd)
Key type: Authenticated key from P-256 (0x03)
Central: 0x00
Encryption size: 16
Diversifier[2]: 0000
Randomizer[8]: 0000000000000000
Key[16]: 6ed96089bd9765be2f2c971b0b95f624
LE Address: D7:2A:DE:1E:73:A2 (Static)
Key type: Unauthenticated key from P-256 (0x02)
Central: 0x00
Encryption size: 16
Diversifier[2]: 0000
Randomizer[8]: 0000000000000000
Key[16]: 87dd2546ededda380ffcdc0a8faa4597
@ MGMT Event: Command Status (0x0002) plen 3 {0x0001} [hci0]
Load Long Term Keys (0x0013)
Status: Invalid Parameters (0x0d)
Cc: [email protected]
Link: https://github.com/bluez/bluez/issues/875
Fixes: 59b047bc9808 ("Bluetooth: MGMT/SMP: Fix address type when using SMP over BREDR/LE")
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
MGMT_OP_DISCONNECT can be called while mgmt_device_connected has not
been called yet, which will cause the connection procedure to be
aborted, so mgmt_device_disconnected shall still respond with command
complete to MGMT_OP_DISCONNECT and just not emit
MGMT_EV_DEVICE_DISCONNECTED since MGMT_EV_DEVICE_CONNECTED was never
sent.
To fix this MGMT_OP_DISCONNECT is changed to work similarly to other
command which do use hci_cmd_sync_queue and then use hci_conn_abort to
disconnect and returns the result, in order for hci_conn_abort to be
used from hci_cmd_sync context it now uses hci_cmd_sync_run_once.
Link: https://github.com/bluez/bluez/issues/932
Fixes: 12d4a3b2ccb3 ("Bluetooth: Move check for MGMT_CONNECTED flag into mgmt.c")
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
This introduces hci_cmd_sync_run/hci_cmd_sync_run_once which acts like
hci_cmd_sync_queue/hci_cmd_sync_queue_once but runs immediately when
already on hdev->cmd_sync_work context.
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
On systems in the field, we are seeing this sometimes in the kernel logs:
Bluetooth: qca_controller_memdump() hci0: hci_devcd_init Return:-95
This means that _something_ decided that it wanted to get a memdump
but then hci_devcd_init() returned -EOPNOTSUPP (AKA -95).
The cleanup code in qca_controller_memdump() when we get back an error
from hci_devcd_init() undoes most things but forgets to clear
QCA_IBS_DISABLED. One side effect of this is that, during the next
suspend, qca_suspend() will always get a timeout.
Let's fix it so that we clear the bit.
Fixes: 06d3fdfcdf5c ("Bluetooth: hci_qca: Add qcom devcoredump support")
Reviewed-by: Guenter Roeck <[email protected]>
Reviewed-by: Stephen Boyd <[email protected]>
Signed-off-by: Douglas Anderson <[email protected]>
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
|
|
Kvaser's PCIe cards uses the KCAN FPGA IP block which has dual 4K
buffers for incoming messages shared by all (currently up to eight)
channels. While the driver processes messages in one buffer, new
incoming messages are stored in the other and so on.
The design of KCAN is such that a buffer must be fully read and then
released. Releasing a buffer will make the FPGA switch buffers. If the
other buffer contains at least one incoming message the FPGA will also
instantly issue a new interrupt, if not the interrupt will be issued
after receiving the first new message.
With IRQx interrupts, it takes a little time for the interrupt to
happen, enough for any previous ISR call to do it's business and
return, but MSI interrupts are way faster so this time is reduced to
almost nothing.
So with MSI, releasing the buffer HAS to be the very last action of
the ISR before returning, otherwise the new interrupt might be
"masked" by the kernel because the previous ISR call hasn't returned.
And the interrupts are edge-triggered so we cannot loose one, or the
ping-pong reading process will stop.
This is why this patch modifies the driver to use a single write to
the SRB_CMD register before returning.
Signed-off-by: Martin Jocic <[email protected]>
Reviewed-by: Vincent Mailhol <[email protected]>
Link: https://patch.msgid.link/[email protected]
Fixes: 26ad340e582d ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices")
Signed-off-by: Marc Kleine-Budde <[email protected]>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into arm/fixes
Microchip AT91 fixes for v6.11
It contains:
- DTS directory update to match all entries not only those starting with
at91 or sama
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/lsm
Pull lsm fix from Paul Moore:
"One small patch to correct a NFS permissions problem with SELinux and
Smack"
* tag 'lsm-pr-20240830' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/lsm:
selinux,smack: don't bypass permissions check in inode_setsecctx hook
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix three issues in the amd-pstate cpufreq driver.
Specifics:
- Remove checks for highest performance match on preferred cores when
updating preferred core ranking in amd-pstate (Mario Limonciello)
- Make amd-pstate call topology_logical_package_id() instead of
logical_die_id() to get a socked ID for a CPU (Gautham Shenoy)
- Fix uninitialized variable in amd_pstate_cpu_boost_update() (Dan
Carpenter)"
* tag 'pm-6.11-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq/amd-pstate-ut: Don't check for highest perf matching on prefcore
cpufreq/amd-pstate: Use topology_logical_package_id() instead of logical_die_id()
cpufreq: amd-pstate: Fix uninitialized variable in amd_pstate_cpu_boost_update()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine
Pull dmaengine fixes from Vinod Koul:
- A bunch of dw driver changes to fix the src/dst addr width config
- Omap driver fix for sglen initialization
- stm32-dma3 driver lli_size init fix
- dw edma driver fixes for watermark interrupts and unmasking STOP and
ABORT interrupts
* tag 'dmaengine-fix-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine:
dmaengine: dw-edma: Do not enable watermark interrupts for HDMA
dmaengine: dw-edma: Fix unmasking STOP and ABORT interrupts for HDMA
dmaengine: stm32-dma3: Set lli_size after allocation
dmaengine: ti: omap-dma: Initialize sglen after allocation
dmaengine: dw: Unify ret-val local variables naming
dmaengine: dw: Simplify max-burst calculation procedure
dmaengine: dw: Define encode_maxburst() above prepare_ctllo() callbacks
dmaengine: dw: Simplify prepare CTL_LO methods
dmaengine: dw: Add memory bus width verification
dmaengine: dw: Add peripheral bus width verification
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy
Pull phy fixes from Vinod Koul:
- Qualcomm QMP X1E80100 PCIe Gen4 PHY initialisation fix
- Freescale imx8mq tuning parameter name fix
- Samsung exynos5 fir for error code in probe()
- Xilinx Zynqmp SGMII linkup failure fix
* tag 'phy-fixes-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy:
phy: xilinx: phy-zynqmp: Fix SGMII linkup failure on resume
phy: exynos5-usbdrd: fix error code in probe()
phy: fsl-imx8mq-usb: fix tuning parameter name
phy: qcom: qmp-pcie: Fix X1E80100 PCIe Gen4 PHY initialisation
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire
Pull soundwire fix from Vinod Koul:
- Single fix for non-continous port map programming
* tag 'soundwire-6.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire:
soundwire: stream: fix programming slave ports for non-continous port maps
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux
Pull iommu fixes from Joerg Roedel:
- Fix a device-stall problem in bad io-page-fault setups (faults
received from devices with no supporting domain attached).
- Context flush fix for Intel VT-d.
- Do not allow non-read+non-write mapping through iommufd as most
implementations can not handle that.
- Fix a possible infinite-loop issue in map_pages() path.
- Add Jean-Philippe as reviewer for SMMUv3 SVA support
* tag 'iommu-fixes-v6.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux:
MAINTAINERS: Add Jean-Philippe as SMMUv3 SVA reviewer
iommu: Do not return 0 from map_pages if it doesn't do anything
iommufd: Do not allow creating areas without READ or WRITE
iommu/vt-d: Fix incorrect domain ID in context flush helper
iommu: Handle iommu faults for a bad iopf setup
|
|
When we cork messages in psock->cork, the last message triggers the
flushing will result in sending a sk_msg larger than the current
message size. In this case, in tcp_bpf_send_verdict(), 'copied' becomes
negative at least in the following case:
468 case __SK_DROP:
469 default:
470 sk_msg_free_partial(sk, msg, tosend);
471 sk_msg_apply_bytes(psock, tosend);
472 *copied -= (tosend + delta); // <==== HERE
473 return -EACCES;
Therefore, it could lead to the following BUG with a proper value of
'copied' (thanks to syzbot). We should not use negative 'copied' as a
return value here.
------------[ cut here ]------------
kernel BUG at net/socket.c:733!
Internal error: Oops - BUG: 00000000f2000800 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 UID: 0 PID: 3265 Comm: syz-executor510 Not tainted 6.11.0-rc3-syzkaller-00060-gd07b43284ab3 #0
Hardware name: linux,dummy-virt (DT)
pstate: 61400009 (nZCv daif +PAN -UAO -TCO +DIT -SSBS BTYPE=--)
pc : sock_sendmsg_nosec net/socket.c:733 [inline]
pc : sock_sendmsg_nosec net/socket.c:728 [inline]
pc : __sock_sendmsg+0x5c/0x60 net/socket.c:745
lr : sock_sendmsg_nosec net/socket.c:730 [inline]
lr : __sock_sendmsg+0x54/0x60 net/socket.c:745
sp : ffff800088ea3b30
x29: ffff800088ea3b30 x28: fbf00000062bc900 x27: 0000000000000000
x26: ffff800088ea3bc0 x25: ffff800088ea3bc0 x24: 0000000000000000
x23: f9f00000048dc000 x22: 0000000000000000 x21: ffff800088ea3d90
x20: f9f00000048dc000 x19: ffff800088ea3d90 x18: 0000000000000001
x17: 0000000000000000 x16: 0000000000000000 x15: 000000002002ffaf
x14: 0000000000000000 x13: 0000000000000000 x12: 0000000000000000
x11: 0000000000000000 x10: ffff8000815849c0 x9 : ffff8000815b49c0
x8 : 0000000000000000 x7 : 000000000000003f x6 : 0000000000000000
x5 : 00000000000007e0 x4 : fff07ffffd239000 x3 : fbf00000062bc900
x2 : 0000000000000000 x1 : 0000000000000000 x0 : 00000000fffffdef
Call trace:
sock_sendmsg_nosec net/socket.c:733 [inline]
__sock_sendmsg+0x5c/0x60 net/socket.c:745
____sys_sendmsg+0x274/0x2ac net/socket.c:2597
___sys_sendmsg+0xac/0x100 net/socket.c:2651
__sys_sendmsg+0x84/0xe0 net/socket.c:2680
__do_sys_sendmsg net/socket.c:2689 [inline]
__se_sys_sendmsg net/socket.c:2687 [inline]
__arm64_sys_sendmsg+0x24/0x30 net/socket.c:2687
__invoke_syscall arch/arm64/kernel/syscall.c:35 [inline]
invoke_syscall+0x48/0x110 arch/arm64/kernel/syscall.c:49
el0_svc_common.constprop.0+0x40/0xe0 arch/arm64/kernel/syscall.c:132
do_el0_svc+0x1c/0x28 arch/arm64/kernel/syscall.c:151
el0_svc+0x34/0xec arch/arm64/kernel/entry-common.c:712
el0t_64_sync_handler+0x100/0x12c arch/arm64/kernel/entry-common.c:730
el0t_64_sync+0x19c/0x1a0 arch/arm64/kernel/entry.S:598
Code: f9404463 d63f0060 3108441f 54fffe81 (d4210000)
---[ end trace 0000000000000000 ]---
Fixes: 4f738adba30a ("bpf: create tcp_bpf_ulp allowing BPF to monitor socket TX/RX data")
Reported-by: [email protected]
Cc: Jakub Sitnicki <[email protected]>
Signed-off-by: Cong Wang <[email protected]>
Reviewed-by: John Fastabend <[email protected]>
Acked-by: Martin KaFai Lau <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>
|
|
Add imx mailing list [email protected] for PCI controller of NXP chips
(Layerscape and iMX).
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Frank Li <[email protected]>
Signed-off-by: Bjorn Helgaas <[email protected]>
Acked-by: Richard Zhu <[email protected]>
|
|
The pointer returned by btf_parse_base could be an error pointer.
IS_ERR() check is needed before calling btf_free(base_btf).
Fixes: 8646db238997 ("libbpf,bpf: Share BTF relocate-related code with kernel")
Signed-off-by: Martin KaFai Lau <[email protected]>
Signed-off-by: Andrii Nakryiko <[email protected]>
Reviewed-by: Alan Maguire <[email protected]>
Acked-by: Eduard Zingerman <[email protected]>
Link: https://lore.kernel.org/bpf/[email protected]
|
|
io_provided_buffers_select() returns 0 to indicate success, but it should
be returning 1 to indicate that 1 vec was mapped. This causes peeking
to fail with classic provided buffers, and while that's not a use case
that anyone should use, it should still work correctly.
The end result is that no buffer will be selected, and hence a completion
with '0' as the result will be posted, without a buffer attached.
Fixes: 35c8711c8fc4 ("io_uring/kbuf: add helpers for getting/peeking multiple buffers")
Signed-off-by: Jens Axboe <[email protected]>
|
|
It is not safe to dereference fl->c.flc_owner without first confirming
fl->fl_lmops is the expected manager. nfsd4_deleg_getattr_conflict()
tests fl_lmops but largely ignores the result and assumes that flc_owner
is an nfs4_delegation anyway. This is wrong.
With this patch we restore the "!= &nfsd_lease_mng_ops" case to behave
as it did before the change mentioned below. This is the same as the
current code, but without any reference to a possible delegation.
Fixes: c5967721e106 ("NFSD: handle GETATTR conflict with write delegation")
Signed-off-by: NeilBrown <[email protected]>
Reviewed-by: Jeff Layton <[email protected]>
Signed-off-by: Chuck Lever <[email protected]>
|
|
When adding devm_regulator_bulk_get_const() I missed adding a stub for
when CONFIG_REGULATOR is not enabled. Under certain conditions (like
randconfig testing) this can cause the compiler to reports errors
like:
error: implicit declaration of function 'devm_regulator_bulk_get_const';
did you mean 'devm_regulator_bulk_get_enable'?
Add the stub.
Fixes: 1de452a0edda ("regulator: core: Allow drivers to define their init data as const")
Reported-by: kernel test robot <[email protected]>
Closes: https://lore.kernel.org/oe-kbuild-all/[email protected]/
Cc: Neil Armstrong <[email protected]>
Signed-off-by: Douglas Anderson <[email protected]>
Link: https://patch.msgid.link/20240830073511.1.Ib733229a8a19fad8179213c05e1af01b51e42328@changeid
Signed-off-by: Mark Brown <[email protected]>
|
|
For buffer registration (or updates), a userspace iovec is copied in
and updated. If the application is within a compat syscall, then the
iovec type is compat_iovec rather than iovec. However, the type used
in __io_sqe_buffers_update() and io_sqe_buffers_register() is always
struct iovec, and hence the source is incremented by the size of a
non-compat iovec in the loop. This misses every other iovec in the
source, and will run into garbage half way through the copies and
return -EFAULT to the application.
Maintain the source address separately and assign to our user vec
pointer, so that copies always happen from the right source address.
While in there, correct a bad placement of __user which triggered
the following sparse warning prior to this fix:
io_uring/rsrc.c:981:33: warning: cast removes address space '__user' of expression
io_uring/rsrc.c:981:30: warning: incorrect type in assignment (different address spaces)
io_uring/rsrc.c:981:30: expected struct iovec const [noderef] __user *uvec
io_uring/rsrc.c:981:30: got struct iovec *[noderef] __user
Fixes: f4eaf8eda89e ("io_uring/rsrc: Drop io_copy_iov in favor of iovec API")
Reviewed-by: Gabriel Krisman Bertazi <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial device id for 6.11-rc6
Here's a new modem device id.
This one has been in linux-next with no reported issues.
* tag 'usb-serial-6.11-rc6' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add MeiG Smart SRM825L
|
|
Fix filemap_invalidate_inode() to use invalidate_inode_pages2_range()
rather than truncate_inode_pages_range(). The latter clears the
invalidated bit of a partial pages rather than discarding it entirely.
This causes copy_file_range() to fail on cifs because the partial pages at
either end of the destination range aren't evicted and reread, but rather
just partly cleared.
This causes generic/075 and generic/112 xfstests to fail.
Fixes: 74e797d79cf1 ("mm: Provide a means of invalidation without using launder_folio")
Signed-off-by: David Howells <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
cc: Matthew Wilcox <[email protected]>
cc: Miklos Szeredi <[email protected]>
cc: Trond Myklebust <[email protected]>
cc: Christoph Hellwig <[email protected]>
cc: Andrew Morton <[email protected]>
cc: Alexander Viro <[email protected]>
cc: Christian Brauner <[email protected]>
cc: Jeff Layton <[email protected]>
cc: [email protected]
cc: [email protected]
cc: [email protected]
cc: [email protected]
cc: [email protected]
cc: [email protected]
cc: [email protected]
cc: [email protected]
cc: [email protected]
Signed-off-by: Christian Brauner <[email protected]>
|
|
sm8250 and sc7280 have lpass codec version 1.0, as these are very old
platforms, they do not have a reliable way to get the codec version
from core_id registers.
On codec versions below 2.0, even though the core_id registers are
available to read, the values of these registers are not unique to be
able to determine the version of the codec dynamically.
Add the version info into of_data, so that driver does not need to use
core_id registers to get version number for such situations.
Fixes: 378918d59181 ("ASoC: codecs: lpass-macro: add helpers to get codec version")
Signed-off-by: Srinivas Kandagatla <[email protected]>
Tested-by: Amit Pundir <[email protected]>
Reviewed-by: Dmitry Baryshkov <[email protected]>
Tested-by: Bryan O'Donoghue <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Mark Brown <[email protected]>
|
|
We use komeda_crtc_normalize_zpos to normalize zpos of affected planes
to their blending zorder in CU. If there's only one slave plane in
affected planes and its layer_split property is enabled, order++ for
its split layer, so that when calculating the normalized_zpos
of master planes, the split layer of the slave plane is included, but
the max_slave_zorder does not include the split layer and keep zero
because there's only one slave plane in affacted planes, although we
actually use two slave layers in this commit.
In most cases, this bug does not result in a commit failure, but assume
the following situation:
slave_layer 0: zpos = 0, layer split enabled, normalized_zpos =
0;(use slave_layer 2 as its split layer)
master_layer 0: zpos = 2, layer_split enabled, normalized_zpos =
2;(use master_layer 2 as its split layer)
master_layer 1: zpos = 4, normalized_zpos = 4;
master_layer 3: zpos = 5, normalized_zpos = 5;
kcrtc_st->max_slave_zorder = 0;
When we use master_layer 3 as a input of CU in function
komeda_compiz_set_input and check it with function
komeda_component_check_input, the parameter idx is equal to
normailzed_zpos minus max_slave_zorder, the value of idx is 5
and is euqal to CU's max_active_inputs, so that
komeda_component_check_input returns a -EINVAL value.
To fix the bug described above, when calculating the max_slave_zorder
with the layer_split enabled, count the split layer in this calculation
directly.
Signed-off-by: hongchi.peng <[email protected]>
Acked-by: Liviu Dudau <[email protected]>
Signed-off-by: Liviu Dudau <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
Since smc_inet6_prot does not initialize ipv6_pinfo_offset, inet6_create()
copies an incorrect address value, sk + 0 (offset), to inet_sk(sk)->pinet6.
In addition, since inet_sk(sk)->pinet6 and smc_sk(sk)->clcsock practically
point to the same address, when smc_create_clcsk() stores the newly
created clcsock in smc_sk(sk)->clcsock, inet_sk(sk)->pinet6 is corrupted
into clcsock. This causes NULL pointer dereference and various other
memory corruptions.
To solve this problem, you need to initialize ipv6_pinfo_offset, add a
smc6_sock structure, and then add ipv6_pinfo as the second member of
the smc_sock structure.
Reported-by: syzkaller <[email protected]>
Fixes: d25a92ccae6b ("net/smc: Introduce IPPROTO_SMC")
Signed-off-by: Jeongjun Park <[email protected]>
Reviewed-by: Eric Dumazet <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|