| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Our out-of-line atomics are built with a special calling convention,
preventing pointless stack spilling, and allowing us to patch call sites
with ARMv8.1 atomic instructions.
Instrumentation inserted by the compiler may result in calls to
functions not following this special calling convention, resulting in
registers being unexpectedly clobbered, and various problems resulting
from this.
For example, if a kernel is built with KCOV and ARM64_LSE_ATOMICS, the
compiler inserts calls to __sanitizer_cov_trace_pc in the prologues of
the atomic functions. This has been observed to result in spurious
cmpxchg failures, leading to a hang early on in the boot process.
This patch avoids such issues by preventing instrumentation of our
out-of-line atomics.
Signed-off-by: Mark Rutland <[email protected]>
Cc: Catalin Marinas <[email protected]>
Cc: Will Deacon <[email protected]>
Signed-off-by: Will Deacon <[email protected]>
|
|
https://github.com/Broadcom/stblinux into fixes
Pull "Broadcom devicetree-arm64 fixes for 4.17" from Florian Fainelli:
This pull request contains Broadcom ARM64-based SoCs Device Tree fixes
for 4.17, please pull the following:
- Srinath fixes the register base address of all SATA controllers on
Stingray
* tag 'arm-soc/for-4.17/devicetree-arm64-fixes' of https://github.com/Broadcom/stblinux:
arm64: dts: correct SATA addresses for Stingray
|
|
Add missing "altivec unavailable" interrupt injection helper
thus fixing the linker error below:
arch/powerpc/kvm/emulate_loadstore.o: In function `kvmppc_check_altivec_disabled':
arch/powerpc/kvm/emulate_loadstore.c: undefined reference to `.kvmppc_core_queue_vec_unavail'
Fixes: 09f984961c137c4b ("KVM: PPC: Book3S: Add MMIO emulation for VMX instructions")
Signed-off-by: Laurentiu Tudor <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
|
|
smp_send_stop can lock up the IPI path for any subsequent calls,
because the receiving CPUs spin in their handler function. This
started becoming a problem with the addition of an smp_send_stop
call in the reboot path, because panics can reboot after doing
their own smp_send_stop.
The NMI IPI variant was fixed with ac61c11566 ("powerpc: Fix
smp_send_stop NMI IPI handling"), which leaves the smp_call_function
variant.
This is fixed by having smp_send_stop only ever do the
smp_call_function once. This is a bit less robust than the NMI IPI
fix, because any other call to smp_call_function after smp_send_stop
could deadlock, but that has always been the case, and it was not
been a problem before.
Fixes: f2748bdfe1573 ("powerpc/powernv: Always stop secondaries before reboot/shutdown")
Reported-by: Abdul Haleem <[email protected]>
Signed-off-by: Nicholas Piggin <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
|
|
gpstate_timer_handler() uses synchronous smp_call to set the pstate
on the requested core. This causes the below hard lockup:
smp_call_function_single+0x110/0x180 (unreliable)
smp_call_function_any+0x180/0x250
gpstate_timer_handler+0x1e8/0x580
call_timer_fn+0x50/0x1c0
expire_timers+0x138/0x1f0
run_timer_softirq+0x1e8/0x270
__do_softirq+0x158/0x3e4
irq_exit+0xe8/0x120
timer_interrupt+0x9c/0xe0
decrementer_common+0x114/0x120
-- interrupt: 901 at doorbell_global_ipi+0x34/0x50
LR = arch_send_call_function_ipi_mask+0x120/0x130
arch_send_call_function_ipi_mask+0x4c/0x130
smp_call_function_many+0x340/0x450
pmdp_invalidate+0x98/0xe0
change_huge_pmd+0xe0/0x270
change_protection_range+0xb88/0xe40
mprotect_fixup+0x140/0x340
SyS_mprotect+0x1b4/0x350
system_call+0x58/0x6c
One way to avoid this is removing the smp-call. We can ensure that the
timer always runs on one of the policy-cpus. If the timer gets
migrated to a cpu outside the policy then re-queue it back on the
policy->cpus. This way we can get rid of the smp-call which was being
used to set the pstate on the policy->cpus.
Fixes: 7bc54b652f13 ("timers, cpufreq/powernv: Initialize the gpstate timer as pinned")
Cc: [email protected] # v4.8+
Reported-by: Nicholas Piggin <[email protected]>
Reported-by: Pridhiviraj Paidipeddi <[email protected]>
Signed-off-by: Shilpasri G Bhat <[email protected]>
Acked-by: Nicholas Piggin <[email protected]>
Acked-by: Viresh Kumar <[email protected]>
Acked-by: Vaidyanathan Srinivasan <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
- Fix for black screen issues (FDO #104158 and #104425)
- A correction for wrongly applied display W/A
- Fixes for HDA codec interop issue (no audio) and too eager HW timeouts
* tag 'drm-intel-fixes-2018-04-26' of git://anongit.freedesktop.org/drm/drm-intel:
drm/i915/fbdev: Enable late fbdev initial configuration
drm/i915: Use ktime on wait_for
drm/i915: Enable display WA#1183 from its correct spot
drm/i915/audio: set minimum CD clock to twice the BCLK
|
|
If the user specifies an invalid field modifier for a hist trigger,
the current code correctly flags that as an error, but doesn't tell
the user what happened.
Fix this by invoking hist_err() with an appropriate message when
invalid modifiers are specified.
Before:
# echo 'hist:keys=pid:ts0=common_timestamp.junkusecs' >> /sys/kernel/debug/tracing/events/sched/sched_wakeup/trigger
-su: echo: write error: Invalid argument
# cat /sys/kernel/debug/tracing/events/sched/sched_wakeup/hist
After:
# echo 'hist:keys=pid:ts0=common_timestamp.junkusecs' >> /sys/kernel/debug/tracing/events/sched/sched_wakeup/trigger
-su: echo: write error: Invalid argument
# cat /sys/kernel/debug/tracing/events/sched/sched_wakeup/hist
ERROR: Invalid field modifier: junkusecs
Last command: keys=pid:ts0=common_timestamp.junkusecs
Link: http://lkml.kernel.org/r/b043c59fa79acd06a5f14a1d44dee9e5a3cd1248.1524790601.git.tom.zanussi@linux.intel.com
Signed-off-by: Tom Zanussi <[email protected]>
Signed-off-by: Steven Rostedt (VMware) <[email protected]>
|
|
If the user specifies a nonexistent field for a hist trigger, the
current code correctly flags that as an error, but doesn't tell the
user what happened.
Fix this by invoking hist_err() with an appropriate message when
nonexistent fields are specified.
Before:
# echo 'hist:keys=pid:ts0=common_timestamp.usecs' >> /sys/kernel/debug/tracing/events/sched/sched_switch/trigger
-su: echo: write error: Invalid argument
# cat /sys/kernel/debug/tracing/events/sched/sched_switch/hist
After:
# echo 'hist:keys=pid:ts0=common_timestamp.usecs' >> /sys/kernel/debug/tracing/events/sched/sched_switch/trigger
-su: echo: write error: Invalid argument
# cat /sys/kernel/debug/tracing/events/sched/sched_switch/hist
ERROR: Couldn't find field: pid
Last command: keys=pid:ts0=common_timestamp.usecs
Link: http://lkml.kernel.org/r/fdc8746969d16906120f162b99dd71c741e0b62c.1524790601.git.tom.zanussi@linux.intel.com
Signed-off-by: Tom Zanussi <[email protected]>
Reported-by: Masami Hiramatsu <[email protected]>
Signed-off-by: Steven Rostedt (VMware) <[email protected]>
|
|
The flag-printing code used when displaying hist triggers somehow got
dropped during refactoring of the inter-event patchset. This restores
it.
Below are a couple examples - in the first case, .usecs wasn't being
displayed properly for common_timestamps and the second illustrates
the same for other flags such as .execname.
Before:
# echo 'hist:key=common_pid.execname:val=count:sort=count' > /sys/kernel/debug/tracing/events/syscalls/sys_enter_read/trigger
# cat /sys/kernel/debug/tracing/events/syscalls/sys_enter_read/trigger
hist:keys=common_pid:vals=hitcount,count:sort=count:size=2048 [active]
# echo 'hist:keys=pid:ts0=common_timestamp.usecs if comm=="cyclictest"' >> /sys/kernel/debug/tracing/events/sched/sched_wakeup/trigger
# cat /sys/kernel/debug/tracing/events/sched/sched_wakeup/trigger
hist:keys=pid:vals=hitcount:ts0=common_timestamp:sort=hitcount:size=2048:clock=global if comm=="cyclictest" [active]
After:
# echo 'hist:key=common_pid.execname:val=count:sort=count' > /sys/kernel/debug/tracing/events/syscalls/sys_enter_read/trigger
# cat /sys/kernel/debug/tracing/events/syscalls/sys_enter_read/trigger
hist:keys=common_pid.execname:vals=hitcount,count:sort=count:size=2048 [active]
# echo 'hist:keys=pid:ts0=common_timestamp.usecs if comm=="cyclictest"' >> /sys/kernel/debug/tracing/events/sched/sched_wakeup/trigger
# cat /sys/kernel/debug/tracing/events/sched/sched_wakeup/trigger
hist:keys=pid:vals=hitcount:ts0=common_timestamp.usecs:sort=hitcount:size=2048:clock=global if comm=="cyclictest" [active]
Link: http://lkml.kernel.org/r/492bab42ff21806600af98a8ea901af10efbee0c.1524790601.git.tom.zanussi@linux.intel.com
Signed-off-by: Tom Zanussi <[email protected]>
Signed-off-by: Steven Rostedt (VMware) <[email protected]>
|
|
Pull virtio fixups from Michael Tsirkin:
- Latest header update will break QEMU (if it's rebuilt with the new
header) - and it seems that the code there is so fragile that any
change in this header will break it. Add a better interface so users
do not need to change their code every time that header changes.
- Fix virtio console for spec compliance.
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_console: reset on out of memory
virtio_console: move removal code
virtio_console: drop custom control queue cleanup
virtio_console: free buffers after reset
virtio: add ability to iterate over vqs
virtio_console: don't tie bufs to a vq
virtio_balloon: add array of stat names
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
- Add support for new Ryzen chips to k10temp driver
... making Phoronix happy
- Fix inconsistent chip access in nct6683 driver
- Handle absence of few types of sensors in scmi driver
* tag 'hwmon-for-linus-v4.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (k10temp) Add support for AMD Ryzen w/ Vega graphics
hwmon: (k10temp) Add temperature offset for Ryzen 2700X
hwmon: (nct6683) Enable EC access if disabled at boot
hwmon: (scmi) handle absence of few types of sensors
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- fix Aardvark MRRS setting (Evan Wang)
- clarify "bandwidth available" link status message (Jakub Kicinski)
- update Kirin GPIO name to fix probe failure (Loic Poulain)
- fix Aardvark IRQ usage (Victor Gu)
- fix Aardvark config accessor issues (Victor Gu)
* tag 'pci-v4.17-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Add "PCIe" to pcie_print_link_status() messages
PCI: kirin: Fix reset gpio name
PCI: aardvark: Fix PCIe Max Read Request Size setting
PCI: aardvark: Use ISR1 instead of ISR0 interrupt in legacy irq mode
PCI: aardvark: Set PIO_ADDR_LS correctly in advk_pcie_rd_conf()
PCI: aardvark: Fix logic in advk_pcie_{rd,wr}_conf()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
- Add workqueue forward declaration (for new work, but a nice clean up)
- seftest fixes for the new histogram code
- Print output fix for hwlat tracer
- Fix missing system call events - due to change in x86 syscall naming
- Fix kprobe address being used by perf being hashed
* tag 'trace-v4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Fix missing tab for hwlat_detector print format
selftests: ftrace: Add a testcase for multiple actions on trigger
selftests: ftrace: Fix trigger extended error testcase
kprobes: Fix random address output of blacklist file
tracing: Fix kernel crash while using empty filter with perf
tracing/x86: Update syscall trace events to handle new prefixed syscall func names
tracing: Add missing forward declaration
|
|
Make kernel print the correct number of TLB entries on Intel Xeon Phi 7210
(and others)
Before:
[ 0.320005] Last level dTLB entries: 4KB 0, 2MB 0, 4MB 0, 1GB 0
After:
[ 0.320005] Last level dTLB entries: 4KB 256, 2MB 128, 4MB 128, 1GB 16
The entries do exist in the official Intel SMD but the type column there is
incorrect (states "Cache" where it should read "TLB"), but the entries for
the values 0x6B, 0x6C and 0x6D are correctly described as 'Data TLB'.
Signed-off-by: Jacek Tomaka <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Link: https://lkml.kernel.org/r/[email protected]
|
|
Using initcall_t in the __field macro generates the following warning
with clang version 6.0:
include/trace/events/initcall.h:34:3: warning: ordered comparison of
function pointers ('initcall_t' (aka 'int (*)(void)') and 'initcall_t')
__field macro expands to __field_ext macro which does is_signed_type
check on the type argument. Since initcall_t is defined as a function
pointer, using it as the type in the __field macro, leads to an ordered
comparison of function pointer warning, inside the check. Using
__field_struct macro avoids the issue.
Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Rishabh Bhatnagar <[email protected]>
[ Added comment to why we are using field_struct() ]
Signed-off-by: Steven Rostedt (VMware) <[email protected]>
|
|
Caller of uprobe_register is required to keep the inode and containing
mount point referenced.
There was misuse of igrab() in uprobes.c and trace_uprobe.c. This is
because igrab() will not prevent umount of the containing mount point.
To fix this, we added path to struct trace_uprobe, which keeps the inode
and containing mount reference.
For uprobes.c, it is not necessary to call igrab() in uprobe_register(),
as the caller is required to keep the inode reference. The igrab() is
removed and comments on this requirement is added to uprobe_register().
Link: http://lkml.kernel.org/r/CAELBmZB2XX=qEOLAdvGG4cPx4GEntcSnWQquJLUK1ongRj35cA@mail.gmail.com
Link: http://lkml.kernel.org/r/[email protected]
Cc: Ingo Molnar <[email protected]>
Cc: Howard McLauchlan <[email protected]>
Cc: Josef Bacik <[email protected]>
Cc: Srikar Dronamraju <[email protected]>
Acked-by: Miklos Szeredi <[email protected]>
Signed-off-by: Song Liu <[email protected]>
Signed-off-by: Steven Rostedt (VMware) <[email protected]>
|
|
As Miklos reported and suggested:
This pattern repeats two times in trace_uprobe.c and in
kernel/events/core.c as well:
ret = kern_path(filename, LOOKUP_FOLLOW, &path);
if (ret)
goto fail_address_parse;
inode = igrab(d_inode(path.dentry));
path_put(&path);
And it's wrong. You can only hold a reference to the inode if you
have an active ref to the superblock as well (which is normally
through path.mnt) or holding s_umount.
This way unmounting the containing filesystem while the tracepoint is
active will give you the "VFS: Busy inodes after unmount..." message
and a crash when the inode is finally put.
Solution: store path instead of inode.
This patch fixes two instances in trace_uprobe.c. struct path is added to
struct trace_uprobe to keep the inode and containing mount point
referenced.
Link: http://lkml.kernel.org/r/[email protected]
Fixes: f3f096cfedf8 ("tracing: Provide trace events interface for uprobes")
Fixes: 33ea4b24277b ("perf/core: Implement the 'perf_uprobe' PMU")
Cc: [email protected]
Cc: Ingo Molnar <[email protected]>
Cc: Howard McLauchlan <[email protected]>
Cc: Josef Bacik <[email protected]>
Cc: Srikar Dronamraju <[email protected]>
Acked-by: Miklos Szeredi <[email protected]>
Reported-by: Miklos Szeredi <[email protected]>
Signed-off-by: Song Liu <[email protected]>
Signed-off-by: Steven Rostedt (VMware) <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These are two watchdog-related fixes, fix for a backlight regression
from the 4.16 cycle that unfortunately was propagated to -stable and a
button module modification to prevent graphics driver modules from
failing to load due to unmet dependencies if ACPI is disabled from the
kernel command line.
Specifics:
- Change the ACPI subsystem initialization ordering to initialize the
WDAT watchodg before reserving PNP motherboard resources so as to
allow the watchdog to allocate its resources before the PNP code
gets to them and prevents it from working correctly (Mika
Westerberg).
- Add a quirk for Lenovo Z50-70 to use the iTCO watchdog instead of
the WDAT one which conflicts with the RTC on that platform (Mika
Westerberg).
- Avoid breaking backlight handling on Dell XPS 13 2013 model by
allowing laptops to use the ACPI backlight by default even if they
are Windows 8-ready in principle (Hans de Goede)"
* tag 'acpi-4.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / video: Only default only_lcd to true on Win8-ready _desktops_
ACPI / button: make module loadable when booted in non-ACPI mode
ACPI / watchdog: Prefer iTCO_wdt on Lenovo Z50-70
ACPI / scan: Initialize watchdog before PNP
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These are a Low Power S0 Idle quirk, a hibernation handling fix for
the PCI bus type and a brcmstb-avs-cpufreq driver fixup removing
development debug code from it.
Specifics:
- Blacklist the Low Power S0 Idle _DSM on ThinkPad X1 Tablet(2016)
where it causes issues and make it use ACPI S3 which works instead
of the non-working suspend-to-idle by default (Chen Yu).
- Fix the handling of hibernation in the PCI core for devices with
the DPM_FLAG_SMART_SUSPEND flag set to fix a regression affecting
intel-lpss I2C devices (Mika Westerberg).
- Drop development debug code from the brcmstb-avs-cpufreq driver
(Markus Mayer)"
* tag 'pm-4.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: brcmstb-avs-cpufreq: remove development debug support
PCI / PM: Do not clear state_saved in pci_pm_freeze() when smart suspend is set
ACPI / PM: Blacklist Low Power S0 Idle _DSM for ThinkPad X1 Tablet(2016)
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull /dev/random fixes from Ted Ts'o:
"Fix a regression on NUMA kernels and suppress excess unseeded entropy
pool warnings"
* tag 'random_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
random: rate limit unseeded randomness warnings
random: fix possible sleeping allocation from irq context
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"A couple of bug fixes:
- correct some CPU-MF counter names for z13 and z14
- correct locking in the vfio-ccw fsm_io_helper function
- provide arch_uretprobe_is_alive to avoid sigsegv with uretprobes
- fix a corner case with CPU-MF sampling in regard to execve
- fix expoline code revert for loadable modules
- update chpid descriptor for resource accessibility events
- fix dasd I/O errors due to outdated device alias infomation"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: correct module section names for expoline code revert
vfio: ccw: process ssch with interrupts disabled
s390: update sampling tag after task pid change
s390/cpum_cf: rename IBM z13/z14 counter names
s390/dasd: fix IO error for newly defined devices
s390/uprobes: implement arch_uretprobe_is_alive()
s390/cio: update chpid descriptor after resource accessibility event
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.17-rc3
Here are a few device ids for -rc3, including a new "simple driver".
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <[email protected]>
|
|
The block responsible of parsing the DT for the number of chip-select
lines uses an 'if/else if/else if' block. The content of the second and
third 'else if' conditions are:
1/ the actual condition to enter the sub-block and
2/ the operation to do in this sub-block.
[...]
else if (condition1_to_enter && action1() == failed)
raise_error();
else if (condition2_to_enter && action2() == failed)
raise_error();
[...]
In case of failure, the sub-block is entered and an error raised.
Otherwise, in case of success, the code would continue erroneously in
the next 'else if' statement because it did not failed (and did not
enter the first 'else if' sub-block).
The first 'else if' refers to legacy bindings while the second 'else if'
refers to new bindings. The second 'else if', which is entered
erroneously, checks for the 'reg' property, which, for old bindings,
does not mean anything because it would not be the number of CS
available, but the regular register map of almost any DT node. This
being said, the content of the 'reg' property being the register map
offset and length, it has '2' values, so the number of CS in this
situation is assumed to be '2'.
When running nand_scan_ident() with 2 CS, the core will check for an
array of chips. It will first issue a RESET and then a READ_ID. Of
course this will trigger two timeouts because there is no chip in front
of the second CS:
[ 1.367460] marvell-nfc f2720000.nand: Timeout on CMDD (NDSR: 0x00000080)
[ 1.474292] marvell-nfc f2720000.nand: Timeout on CMDD (NDSR: 0x00000280)
Indeed, this is harmless and the core will then assume there is only one
valid CS.
Fix the logic in the whole block by entering each sub-block just on the
'is legacy' condition, doing the action inside the sub-block. This way,
when the action succeeds, the whole block is left.
Furthermore, for both the old bindings and the new bindings the same
logic was applied to retrieve the number of CS lines:
using of_get_property() to get a size in bytes, converted in the actual
number of lines by dividing it per sizeof(u32) (4 bytes).
This is fine for the 'reg' property which is a list of the CS IDs but
not for the 'num-cs' property which is directly the value of the number
of CS.
Anyway, no existing DT uses another value than 'num-cs = <1>' and no
other value has ever been supported by the old driver (pxa3xx_nand.c).
Remove this condition and apply a number of 1 CS anyway, as already
described in the bindings.
Finally, the 'reg' property of a 'nand' node (with the new bindings)
gives the IDs of each CS line in use. marvell_nand.c driver first look
at the number of CS lines that are present in this property.
Better use of_property_count_elems_of_size() than dividing by 4 the size
of the number of bytes returned by of_get_property().
Fixes: 02f26ecf8c772 ("mtd: nand: add reworked Marvell NAND controller driver")
Cc: [email protected]
Signed-off-by: Miquel Raynal <[email protected]>
Tested-by: Chris Packham <[email protected]>
Signed-off-by: Boris Brezillon <[email protected]>
|
|
It's possible for userspace to control n. Sanitize n when using it as an
array index.
Note that while it appears that n must be bound to the interval [0,3]
due to the way it is extracted from addr, we cannot guarantee that
compiler transformations (and/or future refactoring) will ensure this is
the case, and given this is a slow path it's better to always perform
the masking.
Found by smatch.
Signed-off-by: Mark Rutland <[email protected]>
Acked-by: Christoffer Dall <[email protected]>
Acked-by: Marc Zyngier <[email protected]>
Cc: [email protected]
Signed-off-by: Will Deacon <[email protected]>
|
|
It's possible for userspace to control intid. Sanitize intid when using
it as an array index.
At the same time, sort the includes when adding <linux/nospec.h>.
Found by smatch.
Signed-off-by: Mark Rutland <[email protected]>
Acked-by: Christoffer Dall <[email protected]>
Acked-by: Marc Zyngier <[email protected]>
Cc: [email protected]
Signed-off-by: Will Deacon <[email protected]>
|
|
It's possible for userspace to control idx. Sanitize idx when using it
as an array index.
Found by smatch.
Signed-off-by: Mark Rutland <[email protected]>
Cc: Catalin Marinas <[email protected]>
Cc: Will Deacon <[email protected]>
Signed-off-by: Will Deacon <[email protected]>
|
|
ceph_con_workfn() validates con->state before calling try_read() and
then try_write(). However, try_read() temporarily releases con->mutex,
notably in process_message() and ceph_con_in_msg_alloc(), opening the
window for ceph_con_close() to sneak in, close the connection and
release con->sock. When try_write() is called on the assumption that
con->state is still valid (i.e. not STANDBY or CLOSED), a NULL sock
gets passed to the networking stack:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000020
IP: selinux_socket_sendmsg+0x5/0x20
Make sure con->state is valid at the top of try_write() and add an
explicit BUG_ON for this, similar to try_read().
Cc: [email protected]
Link: https://tracker.ceph.com/issues/23706
Signed-off-by: Ilya Dryomov <[email protected]>
Reviewed-by: Jason Dillaman <[email protected]>
|
|
This updates the Gemini defconfig with a config that will bring
up most of the recently merged and updated devices to some
functional level:
- We enable high resolution timers (the right thing to do)
- Enable CMA for the framebuffer, and the new TVE200
framebuffer driver and the Ilitek ILI9322 driver for
graphics on the D-Link DIR-685. HIGHMEM support comes in
as part of this.
- Enable networking and the new Cortina Gemini ethernet
driver.
- Enable MDIO over GPIO and the Realtek PHY devices used on
several of these systems.
- Enable I2C over GPIO and SPI over GPIO which is used on
several of these devices.
- Enable the Thermal framework, GPIO fan control and LM75 sensor
adding cooling on the D-Link DNS-313 with no userspace
involved even if only the kernel is working, rock solid
thermal for this platform.
- Enable JEDEC flash probing to support the Eon flash chip in
D-Link DNS-313.
- Enable LED disk triggers for the NAS type devices.
Signed-off-by: Linus Walleij <[email protected]>
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
One of the bitbanged SPI hosts had wrongly named GPIO lines due to
sloppiness by yours truly.
Cc: [email protected]
Cc: Mark Brown <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Pull "Two fixes for v4.17-rc cycle" from Tony Lindgren:
Fix a build regression with split object directories reported by Russell
and fix range sizes for omap4 cm2 and prm modules.
* tag 'omap-for-v4.17/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix build when using split object directories
ARM: dts: Fix cm2 and prm sizes for omap4
|
|
For ACPI support of the HiSilicon LPC driver we depend
on MFD_CORE config.
Currently the HiSi LPC Kconfig entry does not define this
dependency, so add it.
The reason for depending on MFD_CORE in the driver is
that we model the LPC host as an MFD, in that a platform
device will be created for each device on the bus.
We do this as we need to modify the resources of these
derived platform devices, something which we should not
do to the original devices created in the ACPI scan.
Details in e0aa1563f894 ("HISI LPC: Add ACPI support").
Fixes: e0aa1563f894 ("HISI LPC: Add ACPI support")
Reported-and-tested-by: Tan Xiaojun <[email protected]>
Signed-off-by: John Garry <[email protected]>
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into fixes
Pull "Amlogic fixes for v4.17-rc1" from Kevin Hilman:
- add / enable USB host support for GX boards
* tag 'amlogic-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM64: dts: meson-gxm-khadas-vim2: enable the USB controller
ARM64: dts: meson-gxl-nexbox-a95x: enable the USB controller
ARM64: dts: meson-gxl-s905x-libretech-cc: enable the USB controller
ARM64: dts: meson-gx-p23x-q20x: enable the USB controller
ARM64: dts: meson-gxl-s905x-p212: enable the USB controller
ARM64: dts: meson-gxm: add GXM specific USB host configuration
ARM64: dts: meson-gxl: add USB host support
|
|
The DTS file for the NAS4220B had the pin config for the
ethernet interface set to the pins in the SL3512 SoC while
this system is using SL3516. Fix it by referencing the
right SL3516 pins instead of the SL3512 pins.
Cc: [email protected]
Cc: Hans Ulli Kroll <[email protected]>
Reported-by: Andreas Fiedler <[email protected]>
Reported-by: Roman Yeryomin <[email protected]>
Tested-by: Roman Yeryomin <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
I am leaving Axis, so this address will bounce in the not too
distant future.
Fortunately, I will still be working with the community.
Signed-off-by: Niklas Cassel <[email protected]>
Signed-off-by: Arnd Bergmann <[email protected]>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into fixes
SCMI fix for v4.17
A single patch eliminating the redundant null pointer check detected
by CoverityScan("Array compared against 0")
* tag 'scmi-fixes-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
firmware: arm_scmi: remove redundant null check on array
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into fixes
Pull "ARMv8 Juno DT fix for v4.17" from Sudeep Holla:
A single patch to fix the new DTC warnings probably enabled during
v4.17 merge window.
* tag 'juno-fixes-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm64: dts: juno: drop unnecessary address-cells and size-cells properties
|
|
https://github.com/Broadcom/stblinux into fixes
This pull request contains Broadcom SoCs drivers fixes, please pull the
following:
- Geert makes the Raspberry Pi firmwware return -ENOSYS (similar to
other subsystems) when CONFIG_RASPBERRYPI_FIRMWARE is off.
- Florian fixes an incorrect annotation in the Raspberry Pi power domain
driver, spotted by sparse
* tag 'arm-soc/for-4.17/drivers-fixes' of https://github.com/Broadcom/stblinux:
soc: bcm2835: Make !RASPBERRYPI_FIRMWARE dummies return failure
soc: bcm: raspberrypi-power: Fix use of __packed
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into fixes
ARM: socfpga_defconfig: fix QSPI Sector 4k
- disable CONFIG_MTD_SPI_NOR_USE_4K_SECTORS
* tag 'socfpga_defconfig_fix_v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: socfpga_defconfig: Remove QSPI Sector 4K size force
|
|
Recent AMD systems support using MWAIT for C1 state. However, MWAIT will
not allow deeper cstates than C1 on current systems.
play_dead() expects to use the deepest state available. The deepest state
available on AMD systems is reached through SystemIO or HALT. If MWAIT is
available, it is preferred over the other methods, so the CPU never reaches
the deepest possible state.
Don't try to use MWAIT to play_dead() on AMD systems. Instead, use CPUIDLE
to enter the deepest state advertised by firmware. If CPUIDLE is not
available then fallback to HALT.
Signed-off-by: Yazen Ghannam <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Reviewed-by: Borislav Petkov <[email protected]>
Cc: [email protected]
Cc: Yazen Ghannam <[email protected]>
Link: https://lkml.kernel.org/r/[email protected]
|
|
In error path of snd_dice_stream_init_duplex(), stream data for incoming
packet can be left to be initialized.
This commit fixes it.
Fixes: 436b5abe2224 ('ALSA: dice: handle whole available isochronous streams')
Cc: <[email protected]> # v4.6+
Signed-off-by: Takashi Sakamoto <[email protected]>
Signed-off-by: Takashi Iwai <[email protected]>
|
|
* acpi-watchdog:
ACPI / watchdog: Prefer iTCO_wdt on Lenovo Z50-70
* acpi-button:
ACPI / button: make module loadable when booted in non-ACPI mode
* acpi-video:
ACPI / video: Only default only_lcd to true on Win8-ready _desktops_
|
|
* acpi-pm:
ACPI / PM: Blacklist Low Power S0 Idle _DSM for ThinkPad X1 Tablet(2016)
* pm-cpufreq:
cpufreq: brcmstb-avs-cpufreq: remove development debug support
|
|
Commits 9b46a051e4 ("x86/mm: Initialize vmemmap_base at boot-time") and
a7412546d8 ("x86/mm: Adjust vmalloc base and size at boot-time") lost the
type information for __VMALLOC_BASE_L4, __VMALLOC_BASE_L5,
__VMEMMAP_BASE_L4 and __VMEMMAP_BASE_L5 constants.
Declare them explicitly unsigned long again.
Fixes: 9b46a051e4 ("x86/mm: Initialize vmemmap_base at boot-time")
Fixes: a7412546d8 ("x86/mm: Adjust vmalloc base and size at boot-time")
Signed-off-by: Jiri Kosina <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Acked-by: "Kirill A. Shutemov" <[email protected]>
Link: https://lkml.kernel.org/r/[email protected]
|
|
Revert commits
92af4dcb4e1c ("tracing: Unify the "boot" and "mono" tracing clocks")
127bfa5f4342 ("hrtimer: Unify MONOTONIC and BOOTTIME clock behavior")
7250a4047aa6 ("posix-timers: Unify MONOTONIC and BOOTTIME clock behavior")
d6c7270e913d ("timekeeping: Remove boot time specific code")
f2d6fdbfd238 ("Input: Evdev - unify MONOTONIC and BOOTTIME clock behavior")
d6ed449afdb3 ("timekeeping: Make the MONOTONIC clock behave like the BOOTTIME clock")
72199320d49d ("timekeeping: Add the new CLOCK_MONOTONIC_ACTIVE clock")
As stated in the pull request for the unification of CLOCK_MONOTONIC and
CLOCK_BOOTTIME, it was clear that we might have to revert the change.
As reported by several folks systemd and other applications rely on the
documented behaviour of CLOCK_MONOTONIC on Linux and break with the above
changes. After resume daemons time out and other timeout related issues are
observed. Rafael compiled this list:
* systemd kills daemons on resume, after >WatchdogSec seconds
of suspending (Genki Sky). [Verified that that's because systemd uses
CLOCK_MONOTONIC and expects it to not include the suspend time.]
* systemd-journald misbehaves after resume:
systemd-journald[7266]: File /var/log/journal/016627c3c4784cd4812d4b7e96a34226/system.journal
corrupted or uncleanly shut down, renaming and replacing.
(Mike Galbraith).
* NetworkManager reports "networking disabled" and networking is broken
after resume 50% of the time (Pavel). [May be because of systemd.]
* MATE desktop dims the display and starts the screensaver right after
system resume (Pavel).
* Full system hang during resume (me). [May be due to systemd or NM or both.]
That happens on debian and open suse systems.
It's sad, that these problems were neither catched in -next nor by those
folks who expressed interest in this change.
Reported-by: Rafael J. Wysocki <[email protected]>
Reported-by: Genki Sky <[email protected]>,
Reported-by: Pavel Machek <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Cc: Dmitry Torokhov <[email protected]>
Cc: John Stultz <[email protected]>
Cc: Jonathan Corbet <[email protected]>
Cc: Kevin Easton <[email protected]>
Cc: Linus Torvalds <[email protected]>
Cc: Mark Salyzyn <[email protected]>
Cc: Michael Kerrisk <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Petr Mladek <[email protected]>
Cc: Prarit Bhargava <[email protected]>
Cc: Sergey Senozhatsky <[email protected]>
Cc: Steven Rostedt <[email protected]>
|
|
Kaike reported that in tests rdma hrtimers occasionaly stopped working. He
did great debugging, which provided enough context to decode the problem.
CPU 3 CPU 2
idle
start sched_timer expires = 712171000000
queue->next = sched_timer
start rdmavt timer. expires = 712172915662
lock(baseof(CPU3))
tick_nohz_stop_tick()
tick = 716767000000 timerqueue_add(tmr)
hrtimer_set_expires(sched_timer, tick);
sched_timer->expires = 716767000000 <---- FAIL
if (tmr->expires < queue->next->expires)
hrtimer_start(sched_timer) queue->next = tmr;
lock(baseof(CPU3))
unlock(baseof(CPU3))
timerqueue_remove()
timerqueue_add()
ts->sched_timer is queued and queue->next is pointing to it, but then
ts->sched_timer.expires is modified.
This not only corrupts the ordering of the timerqueue RB tree, it also
makes CPU2 see the new expiry time of timerqueue->next->expires when
checking whether timerqueue->next needs to be updated. So CPU2 sees that
the rdma timer is earlier than timerqueue->next and sets the rdma timer as
new next.
Depending on whether it had also seen the new time at RB tree enqueue, it
might have queued the rdma timer at the wrong place and then after removing
the sched_timer the RB tree is completely hosed.
The problem was introduced with a commit which tried to solve inconsistency
between the hrtimer in the tick_sched data and the underlying hardware
clockevent. It split out hrtimer_set_expires() to store the new tick time
in both the NOHZ and the NOHZ + HIGHRES case, but missed the fact that in
the NOHZ + HIGHRES case the hrtimer might still be queued.
Use hrtimer_start(timer, tick...) for the NOHZ + HIGHRES case which sets
timer->expires after canceling the timer and move the hrtimer_set_expires()
invocation into the NOHZ only code path which is not affected as it merily
uses the hrtimer as next event storage so code pathes can be shared with
the NOHZ + HIGHRES case.
Fixes: d4af6d933ccf ("nohz: Fix spurious warning when hrtimer and clockevent get out of sync")
Reported-by: "Wan Kaike" <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Acked-by: Frederic Weisbecker <[email protected]>
Cc: "Marciniszyn Mike" <[email protected]>
Cc: Anna-Maria Gleixner <[email protected]>
Cc: [email protected]
Cc: "Dalessandro Dennis" <[email protected]>
Cc: "Fleck John" <[email protected]>
Cc: [email protected]
Cc: Peter Zijlstra <[email protected]>
Cc: Frederic Weisbecker <[email protected]>
Cc: "Weiny Ira" <[email protected]>
Cc: "[email protected]"
Link: https://lkml.kernel.org/r/[email protected]
Link: https://lkml.kernel.org/r/[email protected]
|
|
The macro FPU_IRQ has never been used since v3.10, So remove it.
Signed-off-by: Dou Liyang <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Cc: [email protected]
Link: https://lkml.kernel.org/r/[email protected]
|
|
The driver_override implementation is susceptible to a race condition
when different threads are reading vs storing a different driver
override. Add locking to avoid this race condition.
Cfr. commits 6265539776a0810b ("driver core: platform: fix race
condition with driver_override") and 9561475db680f714 ("PCI: Fix race
condition with driver_override").
Fixes: 3cf385713460eb2b ("ARM: 8256/1: driver coamba: add device binding path 'driver_override'")
Signed-off-by: Geert Uytterhoeven <[email protected]>
Reviewed-by: Todd Kjos <[email protected]>
Cc: stable <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
For AMBA devices with unconfigured driver override, the
"driver_override" sysfs virtual file is empty, while it contains
"(null)" for platform and PCI devices.
Make AMBA consistent with other buses by dropping the test for a NULL
pointer.
Note that contrary to popular belief, sprintf() handles NULL pointers
fine; they are printed as "(null)".
Signed-off-by: Geert Uytterhoeven <[email protected]>
Cc: stable <[email protected]>
Reviewed-by: Todd Kjos <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
This reverts commit 6b614a87f3f477571e319281e84dba11e0ea0a76.
My backport was incorrect, as Geert pointed out :(
Reported-by: Geert Uytterhoeven <[email protected]>
Cc: Todd Kjos <[email protected]>
Cc: stable <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Now, Linux uses matrix allocator for vector assignment, the original
assignment code which used VECTOR_OFFSET_START has been removed.
So remove the stale macro as well.
Fixes: commit 69cde0004a4b ("x86/vector: Use matrix allocator for vector assignment")
Signed-off-by: Dou Liyang <[email protected]>
Signed-off-by: Thomas Gleixner <[email protected]>
Acked-by: David Rientjes <[email protected]>
Cc: [email protected]
Link: https://lkml.kernel.org/r/[email protected]
Signed-off-by: Ingo Molnar <[email protected]>
|