| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The MICBIAS is a supply, should route to MIC while not IN1L.
Signed-off-by: Bo Shen <[email protected]>
Signed-off-by: Nicolas Ferre <[email protected]>
|
|
The second property of reg is the length, so correct it for timer.
Signed-off-by: Bo Shen <[email protected]>
Signed-off-by: Nicolas Ferre <[email protected]>
|
|
Commit b856a59141b1 (arm/arm64: KVM: Reset the HCR on each vcpu
when resetting the vcpu) moved the init of the HCR register to
happen later in the init of a vcpu, but left out the fixup
done in kvm_reset_vcpu when preparing for a 32bit guest.
As a result, the 32bit guest is run as a 64bit guest, but the
rest of the kernel still manages it as a 32bit. Fun follows.
Moving the fixup to vcpu_reset_hcr solves the problem for good.
Signed-off-by: Marc Zyngier <[email protected]>
Signed-off-by: Christoffer Dall <[email protected]>
Signed-off-by: Paolo Bonzini <[email protected]>
|
|
It took about two years for someone to notice that the IPA passed
to TLBI IPAS2E1IS must be shifted by 12 bits. Clearly our reviewing
is not as good as it should be...
Paper bag time for me.
Reported-by: Mario Smarduch <[email protected]>
Tested-by: Mario Smarduch <[email protected]>
Signed-off-by: Marc Zyngier <[email protected]>
Signed-off-by: Christoffer Dall <[email protected]>
Signed-off-by: Paolo Bonzini <[email protected]>
|
|
With the introduction of the linear mapped p2m list setting memory
areas to "invalid" had to be delayed. When doing the invalidation
make sure no zero sized areas are processed.
Signed-off-by: Juegren Gross <[email protected]>
Signed-off-by: David Vrabel <[email protected]>
|
|
When converting a pfn to a physical address be sure to use 64 bit
wide types or convert the physical address to a pfn if possible.
Signed-off-by: Juergen Gross <[email protected]>
Tested-by: Boris Ostrovsky <[email protected]>
Signed-off-by: David Vrabel <[email protected]>
|
|
When allocating a new pmd for the linear mapped p2m list a check is
done for not introducing another pmd when this just happened on
another cpu. In this case the old pte pointer was returned which
points to the p2m_missing or p2m_identity page. The correct value
would be the pointer to the found new page.
Signed-off-by: Juergen Gross <[email protected]>
Signed-off-by: David Vrabel <[email protected]>
|
|
In xen_rebuild_p2m_list() for large areas of invalid or identity
mapped memory the pmd entries on 32 bit systems are initialized
wrong. Correct this error.
Suggested-by: Boris Ostrovsky <[email protected]>
Signed-off-by: Juergen Gross <[email protected]>
Signed-off-by: David Vrabel <[email protected]>
|
|
git://git.infradead.org/users/jcooper/linux into irq/urgent
irqchip urgent fixes for v3.19 from Jason Cooper
- mtk-sysirq: Fix error handling
- hip04: Fix cpu map for 16bit value
- gic-v3-its: Clear a warning regarding decimal constants
- omap-intc: Fix legacy DMA regression
- atmel-aic-common: Retain priority when changing type
|
|
If uprobes are single stepped for example with gdb, the behavior should
now be correct. Before this patch, when gdb was single stepping a uprobe,
the result was a SIGILL.
When PER is active for any storage alteration and a uprobe is hit, a storage
alteration event is indicated. These over indications are filterd out by gdb,
if no change has happened within the observed area.
Signed-off-by: Jan Willeke <[email protected]>
Signed-off-by: Martin Schwidefsky <[email protected]>
|
|
If a USB serial device (e.g. /dev/ttyUSB0) with an active program is
unplugged, an -ENODEV (19) error will be produced after it gives up
trying to resubmit a read.
usb_serial_generic_submit_read_urb - usb_submit_urb failed: -19
Add -ENODEV as one of the permanent errors along with -EPERM that
usb_serial_generic_submit_read_urb() handles quietly without an error.
Signed-off-by: Jeremiah Mahler <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
If a USB serial device is unplugged while there is an active program
using the device it may spam the logs with -EPROTO (71) messages as it
attempts to retry.
Most serial usb drivers (metro-usb, pl2303, mos7840, ...) only output
these messages for debugging. The generic driver treats these as
errors.
Change the default output for the generic serial driver from error to
debug to silence these non-critical errors.
Signed-off-by: Jeremiah Mahler <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
Add PCI IDs for SPT eMMC, SDIO and SD card.
Signed-off-by: Adrian Hunter <[email protected]>
Signed-off-by: Ulf Hansson <[email protected]>
|
|
Add ACPI HID INT344D for an Intel SDIO host controller.
Signed-off-by: Adrian Hunter <[email protected]>
Signed-off-by: Ulf Hansson <[email protected]>
|
|
Sleep in atomic context happened on Trats2 board after inserting or
removing SD card because mmc_gpio_get_cd() was called under spin lock.
Fix this by moving card detection earlier, before acquiring spin lock.
The mmc_gpio_get_cd() call does not have to be protected by spin lock
because it does not access any sdhci internal data.
The sdhci_do_get_cd() call access host flags (SDHCI_DEVICE_DEAD). After
moving it out side of spin lock it could theoretically race with driver
removal but still there is no actual protection against manual card
eject.
Dmesg after inserting SD card:
[ 41.663414] BUG: sleeping function called from invalid context at drivers/gpio/gpiolib.c:1511
[ 41.670469] in_atomic(): 1, irqs_disabled(): 128, pid: 30, name: kworker/u8:1
[ 41.677580] INFO: lockdep is turned off.
[ 41.681486] irq event stamp: 61972
[ 41.684872] hardirqs last enabled at (61971): [<c0490ee0>] _raw_spin_unlock_irq+0x24/0x5c
[ 41.693118] hardirqs last disabled at (61972): [<c04907ac>] _raw_spin_lock_irq+0x18/0x54
[ 41.701190] softirqs last enabled at (61648): [<c0026fd4>] __do_softirq+0x234/0x2c8
[ 41.708914] softirqs last disabled at (61631): [<c00273a0>] irq_exit+0xd0/0x114
[ 41.716206] Preemption disabled at:[< (null)>] (null)
[ 41.721500]
[ 41.722985] CPU: 3 PID: 30 Comm: kworker/u8:1 Tainted: G W 3.18.0-rc5-next-20141121 #883
[ 41.732111] Workqueue: kmmcd mmc_rescan
[ 41.735945] [<c0014d2c>] (unwind_backtrace) from [<c0011c80>] (show_stack+0x10/0x14)
[ 41.743661] [<c0011c80>] (show_stack) from [<c0489d14>] (dump_stack+0x70/0xbc)
[ 41.750867] [<c0489d14>] (dump_stack) from [<c0228b74>] (gpiod_get_raw_value_cansleep+0x18/0x30)
[ 41.759628] [<c0228b74>] (gpiod_get_raw_value_cansleep) from [<c03646e8>] (mmc_gpio_get_cd+0x38/0x58)
[ 41.768821] [<c03646e8>] (mmc_gpio_get_cd) from [<c036d378>] (sdhci_request+0x50/0x1a4)
[ 41.776808] [<c036d378>] (sdhci_request) from [<c0357934>] (mmc_start_request+0x138/0x268)
[ 41.785051] [<c0357934>] (mmc_start_request) from [<c0357cc8>] (mmc_wait_for_req+0x58/0x1a0)
[ 41.793469] [<c0357cc8>] (mmc_wait_for_req) from [<c0357e68>] (mmc_wait_for_cmd+0x58/0x78)
[ 41.801714] [<c0357e68>] (mmc_wait_for_cmd) from [<c0361c00>] (mmc_io_rw_direct_host+0x98/0x124)
[ 41.810480] [<c0361c00>] (mmc_io_rw_direct_host) from [<c03620f8>] (sdio_reset+0x2c/0x64)
[ 41.818641] [<c03620f8>] (sdio_reset) from [<c035a3d8>] (mmc_rescan+0x254/0x2e4)
[ 41.826028] [<c035a3d8>] (mmc_rescan) from [<c003a0e0>] (process_one_work+0x180/0x3f4)
[ 41.833920] [<c003a0e0>] (process_one_work) from [<c003a3bc>] (worker_thread+0x34/0x4b0)
[ 41.841991] [<c003a3bc>] (worker_thread) from [<c003fed8>] (kthread+0xe4/0x104)
[ 41.849285] [<c003fed8>] (kthread) from [<c000f268>] (ret_from_fork+0x14/0x2c)
[ 42.038276] mmc0: new high speed SDHC card at address 1234
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Fixes: 94144a465dd0 ("mmc: sdhci: add get_cd() implementation")
Cc: <[email protected]>
Signed-off-by: Ulf Hansson <[email protected]>
|
|
In commit 5491ce3f79ee ("mmc: sdhci-pxav3: add support for the Armada
38x SDHCI controller"), the sdhci-pxav3 driver was extended to include
support for the SDHCI controller found in the Armada 38x
processor. This mainly involved adding some MBus window related
configuration.
However, this configuration is currently done too early in ->probe():
it is done before clocks are enabled, while this configuration
involves touching the registers of the controller, which will hang the
SoC if the clock is disabled. It wasn't noticed until now because the
bootloader typically leaves gatable clocks enabled, but in situations
where we have a deferred probe (due to a CD GPIO that cannot be taken,
for example), then the probe will be re-tried later, after a clock
disable has been done in the exit path of the failed probe attempt of
the device. This second probe() will hang the system due to the clock
being disabled.
This can for example be produced on Armada 385 GP, which has a CD GPIO
connected to an I2C PCA9555. If the driver for the PCA9555 is not
compiled into the kernel, then we will have the following sequence of
events:
1. The SDHCI probes
2. It does the MBus configuration (which works, because the clock is
left enabled by the bootloader)
3. It enables the clock
4. It tries to get the CD GPIO, which fails due to the driver being
missing, so -EPROBE_DEFER is returned.
5. Before returning -EPROBE_DEFER, the driver cleans up what was
done, which includes disabling the clock.
6. Later on, the SDHCI probe is tried again.
7. It does the MBus configuration, which hangs because the clock is
no longer enabled.
This commit does the obvious fix of doing the MBus configuration after
the clock has been enabled by the driver.
Fixes: 5491ce3f79ee ("mmc: sdhci-pxav3: add support for the Armada 38x SDHCI controller")
Cc: <[email protected]> # v3.15+
Signed-off-by: Thomas Petazzoni <[email protected]>
Signed-off-by: Ulf Hansson <[email protected]>
|
|
Re-tuning for HS400 mode must be done in HS200
mode. Currently there is no support for that.
That needs to be reflected in the code.
Specifically, if tuning is executed in HS400 mode
then return an error, and do not start the
tuning timer if HS200 tuning is being done prior
to switching to HS400.
Note that periodic re-tuning is not expected
to be needed for HS400 but re-tuning is still
needed after the host controller has lost power.
In the case of suspend/resume that is not necessary
because the card is fully re-initialised. That
just leaves runtime suspend/resume with no support
for HS400 re-tuning.
Signed-off-by: Adrian Hunter <[email protected]>
Signed-off-by: Ulf Hansson <[email protected]>
|
|
The tuning timer is always used if the tuning mode
is 1 and there is a tuning count, irrespective of
whether this is the first call, or any subsequent
call. Consequently the logic to start the timer
can be simplified.
Signed-off-by: Adrian Hunter <[email protected]>
Reviewed-by: Aaron Lu <[email protected]>
Signed-off-by: Ulf Hansson <[email protected]>
|
|
A 'goto' can be used to save duplicating unlocking
and returning.
Signed-off-by: Adrian Hunter <[email protected]>
Reviewed-by: Aaron Lu <[email protected]>
Signed-off-by: Ulf Hansson <[email protected]>
|
|
Re-tuning requires that the maximum data length
is limited to 4MiB. The code currently changes
max_blk_count in an attempt to achieve that.
This is wrong because max_blk_count is a different
limit, but it is also un-necessary because
max_req_size is 512KiB anyway. Consequently, the
changes to max_blk_count are removed and the
comment for max_req_size adjusted accordingly.
The comment is also tweaked to show that the 512KiB
limit is a SDMA limit not an ADMA limit.
Signed-off-by: Adrian Hunter <[email protected]>
Reviewed-by: Aaron Lu <[email protected]>
Signed-off-by: Ulf Hansson <[email protected]>
|
|
If CONFIG_DEBUG_MUTEXES is set, the mutex->owner field is only cleared
if the mutex debugging is enabled which introduces a race in our
mutex_is_locked_by() - i.e. we may inspect the old owner value before it
is acquired by the new task.
This is the root cause of this error:
diff --git a/kernel/locking/mutex-debug.c b/kernel/locking/mutex-debug.c
index 5cf6731..3ef3736 100644
--- a/kernel/locking/mutex-debug.c
+++ b/kernel/locking/mutex-debug.c
@@ -80,13 +80,13 @@ void debug_mutex_unlock(struct mutex *lock)
DEBUG_LOCKS_WARN_ON(lock->owner != current);
DEBUG_LOCKS_WARN_ON(!lock->wait_list.prev && !lock->wait_list.next);
- mutex_clear_owner(lock);
}
/*
* __mutex_slowpath_needs_to_unlock() is explicitly 0 for debug
* mutexes so that we can do it here after we've verified state.
*/
+ mutex_clear_owner(lock);
atomic_set(&lock->count, 1);
}
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=87955
Signed-off-by: Chris Wilson <[email protected]>
Cc: [email protected]
Reviewed-by: Daniel Vetter <[email protected]>
Signed-off-by: Jani Nikula <[email protected]>
|
|
Like Ivybridge, we have reports that we get random hangs when flipping
with multiple pipes. Extend
commit 2a92d5bca1999b69c78f3c3e97b5484985b094b9
Author: Chris Wilson <[email protected]>
Date: Tue Jul 8 10:40:29 2014 +0100
drm/i915: Disable RCS flips on Ivybridge
to also apply to Haswell.
Reported-and-tested-by: Scott Tsai <[email protected]>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=87759
Signed-off-by: Chris Wilson <[email protected]>
Reviewed-by: Daniel Vetter <[email protected]>
Cc: [email protected] # 2a92d5bca199 drm/i915: Disable RCS flips on Ivybridge
Cc: [email protected]
Signed-off-by: Jani Nikula <[email protected]>
|
|
We apply the RPS interrupt workaround on VLV everywhere except when
writing the mask directly during idling the GPU. For consistency do this
also there.
While at it also extend the code comment about affected platforms.
I couldn't reproduce the issue on VLV fixed by this workaround, by
removing the workaround from everywhere, while it's 100% reproducible on
SNB using igt/gem_reset_stats/ban-ctx-render. So also add a note that
it hasn't been verified if the workaround really applies to VLV/CHV.
Suggested-by: Daniel Vetter <[email protected]>
Signed-off-by: Imre Deak <[email protected]>
Reviewed-by: Daniel Vetter <[email protected]>
Signed-off-by: Jani Nikula <[email protected]>
|
|
In
commit dbea3cea69508e9d548ed4a6be13de35492e5d15
Author: Imre Deak <[email protected]>
Date: Mon Dec 15 18:59:28 2014 +0200
drm/i915: sanitize RPS resetting during GPU reset
we disable RPS interrupts during GPU resetting, but don't apply the
necessary GEN6 HW workaround. This leads to a HW lockup during a
subsequent "looping batchbuffer" workload. This is triggered by the
testcase that submits exactly this kind of workload after a simulated
GPU reset. I'm not sure how likely the bug would have triggered
otherwise, since we would have applied the workaround anyway shortly
after the GPU reset, when enabling GT powersaving from the deferred
work.
This may also fix unrelated issues, since during driver loading /
suspending we also disable RPS interrupts and so we also had a short
window during the rest of the loading / resuming where a similar
workload could run without the workaround applied.
v2:
- separate the fix to route RPS interrupts to the CPU on GEN9 too
to a separate patch (Daniel)
Bisected-by: Ander Conselvan de Oliveira <[email protected]>
Testcase: igt/gem_reset_stats/ban-ctx-render
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=87429
Signed-off-by: Imre Deak <[email protected]>
Reviewed-by: Daniel Vetter <[email protected]>
Signed-off-by: Jani Nikula <[email protected]>
|
|
GEN8+ HW has the option to route PM interrupts to either the CPU or to
GT. For GEN8 this was already set correctly to routing to CPU, but not
for GEN9, so fix this. Note that when disabling RPS interrupts this was
set already correctly, though in that case it didn't matter much except
for the possibility of spurious interrupts.
Signed-off-by: Imre Deak <[email protected]>
Reviewed-by: Daniel Vetter <[email protected]>
Signed-off-by: Jani Nikula <[email protected]>
|
|
multi_v7_defconfig has it as Y already, so build it in here, too, for
consistency, and therefore build in HWMON as well.
Signed-off-by: Andreas Faerber <[email protected]>
Reviewed-by: Javier Martinez Canillas <[email protected]>
Signed-off-by: Kukjin Kim <[email protected]>
|
|
Many Exynos devices have a display panel. Most of them just have
a simple panel while others have more complex configurations that
requires an embedded DisplayPort (eDP) to LVDS bridges.
This patch enables the following features to be built in the kernel
image to support both setups:
- Direct Rendering Manager (DRM)
- DRM bridge registration and lookup framework
- Parade ps8622/ps8625 eDP/LVDS bridge
- NXP ptn3460 eDP/LVDS bridge
- Exynos Fully Interactive Mobile Display controller (FIMD)
- Panel registration and lookup framework
- Simple panels
- Backlight & LCD device support
Signed-off-by: Javier Martinez Canillas <[email protected]>
Tested-by: Kevin Hilman <[email protected]>
Signed-off-by: Kukjin Kim <[email protected]>
|
|
In commit a3e5b356b3ab "powerpc: Don't use local named register variable
in current_thread_info" Anton changed the way we did current_thread_info()
to accommodate LLVM, and it was not meant to have any effect elsewhere.
Unfortunately it has exposed a gcc bug, where r1 gets copied into
another register and then gcc uses that register to restore the toc
after a function call, even when that register is volatile and has been
clobbered by the function call.
We could revert Anton's patch, but it's not clear the original code is
safe either, we may just have been lucky.
The cleanest solution is to just use the existing CURRENT_THREAD_INFO()
asm macro, and call it using inline asm.
Segher points out we don't need volatile on the asm, if the result of
the shift is unused it's fine for the compiler to elide it.
Fixes: a3e5b356b3ab ("powerpc: Don't use local named register variable in current_thread_info")
Reported-by: Alexander Graf <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
|
|
An issue was introduced with "cxl: Unmap MMIO regions when detaching a
context" (b123429e6a9e8d03aacf888d23262835f0081448) where closing a
context normally could also unmap the problem state area of other
contexts currently using the AFU.
It was also discovered that after a context's MMIO space had been
unmapped it would read 0s when accessing it, whereas the expected
behaviour was for the access to fail altogether.
In order to address these issues, this patch does two things:
- Forced mmap unmapping is only done when we are forcefully detaching
all contexts, and not in the normal detach path. Since the normal
context close path is tied to the file release any mmaps must have
already been released so we don't need to worry in that case.
- The mmap path now uses a vm_operations_struct with a fault handler.
The fault handler ensures that the context is in started state,
otherwise it fails the access attempt with a SIGBUS.
Fixes: b123429e6a9e ("cxl: Unmap MMIO regions when detaching a context")
Signed-off-by: Ian Munsie <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
|
|
Patch c49f63530bb6 ("powernv: Add OPAL tracepoints") has a spurious
store to the stack:
ld r12,opal_tracepoint_refcount@toc(r2); \
std r12,32(r1); \
The store was originally used to save the current tracepoint status
so the entry and the exit tracepoints were always balanced. In the
end I just created a separate path when tracepoints are enabled.
The offset on the stack used for this store is not valid for ABIv2
and it causes strange issues. I noticed it because OPAL console input
was broken.
Fixes: c49f63530bb6 ("powernv: Add OPAL tracepoints")
Cc: <[email protected]> # v3.17+
Signed-off-by: Anton Blanchard <[email protected]>
Signed-off-by: Michael Ellerman <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
* rtlwifi: fix a regression in large skb allocation failure
iwlwifi:
* fix for 7265D NVM check
* fixes for scan: fix long scanning times and network discovery
* new firmware API for iwlmvm supported devices
* fixes in rate control
Signed-off-by: David S. Miller <[email protected]>
|
|
Pablo Neira Ayuso says:
====================
netfilter/ipvs fixes for net
The following patchset contains netfilter/ipvs fixes, they are:
1) Small fix for the FTP helper in IPVS, a diff variable may be left
unset when CONFIG_IP_VS_IPV6 is set. Patch from Dan Carpenter.
2) Fix nf_tables port NAT in little endian archs, patch from leroy
christophe.
3) Fix race condition between conntrack confirmation and flush from
userspace. This is the second reincarnation to resolve this problem.
4) Make sure inner messages in the batch come with the nfnetlink header.
5) Relax strict check from nfnetlink_bind() that may break old userspace
applications using all 1s group mask.
6) Schedule removal of chains once no sets and rules refer to them in
the new nf_tables ruleset flush command. Reported by Asbjoern Sloth
Toennesen.
Note that this batch comes later than usual because of the short
winter holidays.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
Due to a misplaced parenthesis, the expression
(unlikely(offset) < 0),
which expands to
(__builtin_expect(!!(offset), 0) < 0),
never evaluates to true. Therefore, when sending packets with
PF_PACKET/SOCK_DGRAM, packet_snd() does not abort as intended
if the creation of the layer 2 header fails.
Spotted by Coverity - CID 1259975 ("Operands don't affect result").
Fixes: 9c7077622dd9 ("packet: make packet_snd fail on len smaller than l2 header")
Signed-off-by: Christoph Jaeger <[email protected]>
Acked-by: Eric Dumazet <[email protected]>
Acked-by: Willem de Bruijn <[email protected]>
Acked-by: Daniel Borkmann <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Commit d75b1ade567f ("net: less interrupt masking in NAPI") uncovered
wrong alx_poll() behavior.
A NAPI poll() handler is supposed to return exactly the budget when/if
napi_complete() has not been called.
It is also supposed to return number of frames that were received, so
that netdev_budget can have a meaning.
Also, in case of TX pressure, we still have to dequeue received
packets : alx_clean_rx_irq() has to be called even if
alx_clean_tx_irq(alx) returns false, otherwise device is half duplex.
Signed-off-by: Eric Dumazet <[email protected]>
Fixes: d75b1ade567f ("net: less interrupt masking in NAPI")
Reported-by: Oded Gabbay <[email protected]>
Bisected-by: Oded Gabbay <[email protected]>
Tested-by: Oded Gabbay <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
A NAPI poll() handler is supposed to return exactly the budget when/if
napi_complete() has not been called.
It is also supposed to return number of frames that were received, so
that netdev_budget can have a meaning.
Signed-off-by: Eric Dumazet <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Request number for ioctls are encoded as 8bit numbers, but unfortunately
UI_GET_SYSNAME and UI_GET_VERSION specifu values larger than that, so they
get truncated to 44 (0x2c) and 45 (0x2d). This change makes requested
values match their effective values (the ABI stays intact).
Signed-off-by: Gabriel Laskar <[email protected]>
Signed-off-by: Dmitry Torokhov <[email protected]>
|
|
|
|
Pull ARM fixes from Russell King:
"Three small fixes from over the Christmas period, and wiring up the
new execveat syscall for ARM"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8275/1: mm: fix PMD_SECT_RDONLY undeclared compile error
ARM: 8253/1: mm: use phys_addr_t type in map_lowmem() for kernel mem region
ARM: 8249/1: mm: dump: don't skip regions
ARM: wire up execveat syscall
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Misc fixes: two vdso fixes, two kbuild fixes and a boot failure fix
with certain odd memory mappings"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, vdso: Use asm volatile in __getcpu
x86/build: Clean auto-generated processor feature files
x86: Fix mkcapflags.sh bash-ism
x86: Fix step size adjustment during initial memory mapping
x86_64, vdso: Fix the vdso address randomization algorithm
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"Misc fixes: group scheduling corner case fix, two deadline scheduler
fixes, effective_load() overflow fix, nested sleep fix, 6144 CPUs
system fix"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Fix RCU stall upon -ENOMEM in sched_create_group()
sched/deadline: Avoid double-accounting in case of missed deadlines
sched/deadline: Fix migration of SCHED_DEADLINE tasks
sched: Fix odd values in effective_load() calculations
sched, fanotify: Deal with nested sleeps
sched: Fix KMALLOC_MAX_SIZE overflow during cpumask allocation
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Mostly tooling fixes, but also some kernel side fixes: uncore PMU
driver fix, user regs sampling fix and an instruction decoder fix that
unbreaks PEBS precise sampling"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/uncore/hsw-ep: Handle systems with only two SBOXes
perf/x86_64: Improve user regs sampling
perf: Move task_pt_regs sampling into arch code
x86: Fix off-by-one in instruction decoder
perf hists browser: Fix segfault when showing callchain
perf callchain: Free callchains when hist entries are deleted
perf hists: Fix children sort key behavior
perf diff: Fix to sort by baseline field by default
perf list: Fix --raw-dump option
perf probe: Fix crash in dwarf_getcfi_elf
perf probe: Fix to fall back to find probe point in symbols
perf callchain: Append callchains only when requested
perf ui/tui: Print backtrace symbols when segfault occurs
perf report: Show progress bar for output resorting
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Ingo Molnar:
"A liblockdep fix and a mutex_unlock() mutex-debugging fix"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
mutex: Always clear owner field upon mutex_unlock()
tools/liblockdep: Fix debug_check thinko in mutex destroy
|
|
Fix for BUG_ON(anon_vma->degree) splashes in unlink_anon_vmas() ("kernel
BUG at mm/rmap.c:399!") caused by commit 7a3ef208e662 ("mm: prevent
endless growth of anon_vma hierarchy")
Anon_vma_clone() is usually called for a copy of source vma in
destination argument. If source vma has anon_vma it should be already
in dst->anon_vma. NULL in dst->anon_vma is used as a sign that it's
called from anon_vma_fork(). In this case anon_vma_clone() finds
anon_vma for reusing.
Vma_adjust() calls it differently and this breaks anon_vma reusing
logic: anon_vma_clone() links vma to old anon_vma and updates degree
counters but vma_adjust() overrides vma->anon_vma right after that. As
a result final unlink_anon_vmas() decrements degree for wrong anon_vma.
This patch assigns ->anon_vma before calling anon_vma_clone().
Signed-off-by: Konstantin Khlebnikov <[email protected]>
Reported-and-tested-by: Chris Clayton <[email protected]>
Reported-and-tested-by: Oded Gabbay <[email protected]>
Reported-and-tested-by: Chih-Wei Huang <[email protected]>
Acked-by: Rik van Riel <[email protected]>
Acked-by: Vlastimil Babka <[email protected]>
Cc: Daniel Forrest <[email protected]>
Cc: Michal Hocko <[email protected]>
Cc: [email protected] # to match back-porting of 7a3ef208e662
Signed-off-by: Linus Torvalds <[email protected]>
|
|
Commit fee7e49d4514 ("mm: propagate error from stack expansion even for
guard page") made sure that we return the error properly for stack
growth conditions. It also theorized that counting the guard page
towards the stack limit might break something, but also said "Let's see
if anybody notices".
Somebody did notice. Apparently android-x86 sets the stack limit very
close to the limit indeed, and including the guard page in the rlimit
check causes the android 'zygote' process problems.
So this adds the (fairly trivial) code to make the stack rlimit check be
against the actual real stack size, rather than the size of the vma that
includes the guard page.
Reported-and-tested-by: Chih-Wei Huang <[email protected]>
Cc: Jay Foad <[email protected]>
Cc: [email protected] # to match back-porting of fee7e49d4514
Signed-off-by: Linus Torvalds <[email protected]>
|
|
This code is unnecessary, because same logic is already included. Refer
this mail thread[1] for detail.
[1] http://lists.freedesktop.org/archives/dri-devel/2015-January/075132.html
Signed-off-by: Hyungwon Hwang <[email protected]>
Signed-off-by: Inki Dae <[email protected]>
|
|
Check success of execveat(3, '../execveat', 0)... [OK]
Check success of execveat(5, 'execveat', 0)... [OK]
Check success of execveat(6, 'execveat', 0)... [OK]
Check success of execveat(-100, '/root/selftest-exec/exec/execveat', 0)... [OK]
Check success of execveat(99, '/root/selftest-exec/exec/execveat', 0)... [OK]
Check success of execveat(8, '', 4096)... [OK]
Check success of execveat(17, '', 4096)... [OK]
Check success of execveat(9, '', 4096)... [OK]
Check success of execveat(14, '', 4096)... [OK]
Check success of execveat(14, '', 4096)... [OK]
Check success of execveat(15, '', 4096)... [OK]
Check failure of execveat(8, '', 0) with ENOENT... [OK]
Check failure of execveat(8, '(null)', 4096) with EFAULT... [OK]
Check success of execveat(5, 'execveat.symlink', 0)... [OK]
Check success of execveat(6, 'execveat.symlink', 0)... [OK]
Check success of execveat(-100, '/root/selftest-exec/...xec/execveat.symlink', 0)... [OK]
Check success of execveat(10, '', 4096)... [OK]
Check success of execveat(10, '', 4352)... [OK]
Check failure of execveat(5, 'execveat.symlink', 256) with ELOOP... [OK]
Check failure of execveat(6, 'execveat.symlink', 256) with ELOOP... [OK]
Check failure of execveat(-100, '/root/selftest-exec/exec/execveat.symlink', 256) with ELOOP... [OK]
Check success of execveat(3, '../script', 0)... [OK]
Check success of execveat(5, 'script', 0)... [OK]
Check success of execveat(6, 'script', 0)... [OK]
Check success of execveat(-100, '/root/selftest-exec/exec/script', 0)... [OK]
Check success of execveat(13, '', 4096)... [OK]
Check success of execveat(13, '', 4352)... [OK]
Check failure of execveat(18, '', 4096) with ENOENT... [OK]
Check failure of execveat(7, 'script', 0) with ENOENT... [OK]
Check success of execveat(16, '', 4096)... [OK]
Check success of execveat(16, '', 4096)... [OK]
Check success of execveat(4, '../script', 0)... [OK]
Check success of execveat(4, 'script', 0)... [OK]
Check success of execveat(4, '../script', 0)... [OK]
Check failure of execveat(4, 'script', 0) with ENOENT... [OK]
Check failure of execveat(5, 'execveat', 65535) with EINVAL... [OK]
Check failure of execveat(5, 'no-such-file', 0) with ENOENT... [OK]
Check failure of execveat(6, 'no-such-file', 0) with ENOENT... [OK]
Check failure of execveat(-100, 'no-such-file', 0) with ENOENT... [OK]
Check failure of execveat(5, '', 4096) with EACCES... [OK]
Check failure of execveat(5, 'Makefile', 0) with EACCES... [OK]
Check failure of execveat(11, '', 4096) with EACCES... [OK]
Check failure of execveat(12, '', 4096) with EACCES... [OK]
Check failure of execveat(99, '', 4096) with EBADF... [OK]
Check failure of execveat(99, 'execveat', 0) with EBADF... [OK]
Check failure of execveat(8, 'execveat', 0) with ENOTDIR... [OK]
Invoke copy of 'execveat' via filename of length 4093:
Check success of execveat(19, '', 4096)... [OK]
Check success of execveat(5, 'xxxxxxxxxxxxxxxxxxxx...yyyyyyyyyyyyyyyyyyyy', 0)... [OK]
Invoke copy of 'script' via filename of length 4093:
Check success of execveat(20, '', 4096)... [OK]
Check success of execveat(5, 'xxxxxxxxxxxxxxxxxxxx...yyyyyyyyyyyyyyyyyyyy', 0)... [OK]
Signed-off-by: Geert Uytterhoeven <[email protected]>
|
|
locking fixes
Signed-off-by: Ingo Molnar <[email protected]>
|
|
Pull VFIO fix from Alex Williamson:
"Fix PCI header check in vfio_pci_probe() (Wei Yang)"
* tag 'vfio-v3.19-rc4' of git://github.com/awilliam/linux-vfio:
vfio-pci: Fix the check on pci device type in vfio_pci_probe()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fix from James Bottomley:
"Just one fix: a qlogic busy wait regression"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
qla2xxx: fix busy wait regression
|
|
Use tty kref to release the fake tty in usb_console_setup to avoid use
after free if the underlying serial driver has acquired a reference.
Note that using the tty destructor release_one_tty requires some more
state to be initialised.
Fixes: 4a90f09b20f4 ("tty: usb-serial krefs")
Cc: stable <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|