aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2015-01-20ACPI: pci: Do not clear pci_dev->irq in acpi_pci_irq_disable()Jiang Liu1-1/+0
Xen pciback driver assumes that pci_dev->irq won't change after calling pci_disable_device(). But commit cffe0a2b5a34c95a4dadc9ec7132690a5b0f6687 ("x86, irq: Keep balance of IOAPIC pin reference count") frees irq resources and resets pci_dev->irq to zero when pci_disable_device() is called. So this is a hotfix for 3.19 to avoid resetting pci_dev->irq, and another proper fix will be prepared for next merging window. Signed-off-by: Jiang Liu <[email protected]> Tested-by: Sander Eikelenboom <[email protected]> Cc: Tony Luck <[email protected]> Cc: Konrad Rzeszutek Wilk <[email protected]> Cc: David Vrabel <[email protected]> Cc: Rafael J. Wysocki <[email protected]> Cc: Len Brown <[email protected]> Link: http://lkml.kernel.org/r/[email protected] Signed-off-by: Thomas Gleixner <[email protected]>
2015-01-20x86/xen: Treat SCI interrupt as normal GSI interruptJiang Liu2-60/+13
Currently Xen Domain0 has special treatment for ACPI SCI interrupt, that is initialize irq for ACPI SCI at early stage in a special way as: xen_init_IRQ() ->pci_xen_initial_domain() ->xen_setup_acpi_sci() Allocate and initialize irq for ACPI SCI Function xen_setup_acpi_sci() calls acpi_gsi_to_irq() to get an irq number for ACPI SCI. But unfortunately acpi_gsi_to_irq() depends on IOAPIC irqdomains through following path acpi_gsi_to_irq() ->mp_map_gsi_to_irq() ->mp_map_pin_to_irq() ->check IOAPIC irqdomain For PV domains, it uses Xen event based interrupt manangement and doesn't make uses of native IOAPIC, so no irqdomains created for IOAPIC. This causes Xen domain0 fail to install interrupt handler for ACPI SCI and all ACPI events will be lost. Please refer to: https://lkml.org/lkml/2014/12/19/178 So the fix is to get rid of special treatment for ACPI SCI, just treat ACPI SCI as normal GSI interrupt as: acpi_gsi_to_irq() ->acpi_register_gsi() ->acpi_register_gsi_xen() ->xen_register_gsi() With above change, there's no need for xen_setup_acpi_sci() anymore. The above change also works with bare metal kernel too. Signed-off-by: Jiang Liu <[email protected]> Tested-by: Sander Eikelenboom <[email protected]> Cc: Tony Luck <[email protected]> Cc: [email protected] Cc: Konrad Rzeszutek Wilk <[email protected]> Cc: David Vrabel <[email protected]> Cc: Rafael J. Wysocki <[email protected]> Cc: Len Brown <[email protected]> Cc: Pavel Machek <[email protected]> Cc: Bjorn Helgaas <[email protected]> Link: http://lkml.kernel.org/r/[email protected] Signed-off-by: Thomas Gleixner <[email protected]>
2015-01-20Merge tag 'pinctrl-v3.19-3' of ↵Linus Torvalds5-31/+26
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl Pull pin control fixes from Linus Walleij: "Here is a (hopefully final) slew of pin control fixes for the v3.19 series. The deadlock fix is kind of serious and tagged for stable, the rest is business as usual. - Fix two deadlocks around the pin control mutexes, a long-standing issue that manifest itself in plug/unplug of pin controllers. (Tagged for stable.) - Handle an error path with zero functions in the Qualcomm pin controller. - Drop a bogus second GPIO chip added in the Lantiq driver. - Fix sudden IRQ loss on Rockchip pin controllers. - Register the GIT tree in MAINTAINERS" * tag 'pinctrl-v3.19-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: pinctrl: MAINTAINERS: add git tree reference pinctrl: qcom: Don't iterate past end of function array pinctrl: lantiq: remove bogus of_gpio_chip_add pinctrl: Fix two deadlocks pinctrl: rockchip: Avoid losing interrupts when supporting both edges
2015-01-20VFS: Convert file->f_dentry->d_inode to file_inode()David Howells1-1/+1
Convert file->f_dentry->d_inode to file_inode() so as to get layered filesystems right. Found with: git grep '[.>]f_dentry' Signed-off-by: David Howells <[email protected]> Signed-off-by: Al Viro <[email protected]>
2015-01-20scsi: Avoid crashing if device uses DIX but adapter does not support itEwan D. Milne1-1/+11
This can happen if a multipathed device uses DIX and another path is added via an adapter that does not support it. Multipath should not allow this path to be added, but we should not depend upon that to avoid crashing. Signed-off-by: Ewan D. Milne <[email protected]> Reviewed-by: Martin K. Petersen <[email protected]> Signed-off-by: Christoph Hellwig <[email protected]>
2015-01-20scsi_debug: use atomic allocation in resp_rsup_opcodesSasha Levin1-1/+1
resp_rsup_opcodes() may get called from atomic context and would need to use GFP_ATOMIC for allocations: [ 1237.913419] BUG: sleeping function called from invalid context at mm/slub.c:1262 [ 1237.914865] in_atomic(): 1, irqs_disabled(): 0, pid: 7556, name: trinity-c311 [ 1237.916142] 3 locks held by trinity-c311/7556: [ 1237.916981] #0: (sb_writers#5){.+.+.+}, at: do_readv_writev (include/linux/fs.h:2346 fs/read_write.c:844) [ 1237.919713] #1: (&of->mutex){+.+.+.}, at: kernfs_fop_write (fs/kernfs/file.c:297) [ 1237.922626] Mutex: counter: -1 owner: trinity-c311 [ 1237.924044] #2: (s_active#51){.+.+.+}, at: kernfs_fop_write (fs/kernfs/file.c:297) [ 1237.925960] Preemption disabled blk_execute_rq_nowait (block/blk-exec.c:95) [ 1237.927416] [ 1237.927680] CPU: 24 PID: 7556 Comm: trinity-c311 Not tainted 3.19.0-rc4-next-20150116-sasha-00054-g4ad498c-dirty #1744 [ 1237.929603] ffff8804fc9d8000 ffff8804d9bc3548 ffffffff9d439fb2 0000000000000000 [ 1237.931097] 0000000000000000 ffff8804d9bc3588 ffffffff9a18389a ffff8804d9bc3598 [ 1237.932466] ffffffff9a1b1715 ffffffffa15935d8 ffffffff9e6f8cb1 00000000000004ee [ 1237.933984] Call Trace: [ 1237.934434] dump_stack (lib/dump_stack.c:52) [ 1237.935323] ___might_sleep (kernel/sched/core.c:7339) [ 1237.936259] ? mark_held_locks (kernel/locking/lockdep.c:2549) [ 1237.937293] __might_sleep (kernel/sched/core.c:7305) [ 1237.938272] __kmalloc (mm/slub.c:1262 mm/slub.c:2419 mm/slub.c:2491 mm/slub.c:3291) [ 1237.939137] ? resp_rsup_opcodes (include/linux/slab.h:435 drivers/scsi/scsi_debug.c:1689) [ 1237.940173] resp_rsup_opcodes (include/linux/slab.h:435 drivers/scsi/scsi_debug.c:1689) [ 1237.941211] ? add_host_store (drivers/scsi/scsi_debug.c:1584) [ 1237.942261] scsi_debug_queuecommand (drivers/scsi/scsi_debug.c:5276) [ 1237.943404] ? blk_rq_map_sg (block/blk-merge.c:254) [ 1237.944398] ? scsi_init_sgtable (drivers/scsi/scsi_lib.c:1095) [ 1237.945402] sdebug_queuecommand_lock_or_not (drivers/scsi/scsi_debug.c:5300) [ 1237.946735] scsi_dispatch_cmd (drivers/scsi/scsi_lib.c:1706) [ 1237.947720] scsi_queue_rq (drivers/scsi/scsi_lib.c:1996) [ 1237.948687] __blk_mq_run_hw_queue (block/blk-mq.c:816) [ 1237.949796] blk_mq_run_hw_queue (block/blk-mq.c:896) [ 1237.950903] ? _raw_spin_unlock (./arch/x86/include/asm/preempt.h:95 include/linux/spinlock_api_smp.h:154 kernel/locking/spinlock.c:183) [ 1237.951862] blk_mq_insert_request (block/blk-mq.c:1037) [ 1237.952876] blk_execute_rq_nowait (block/blk-exec.c:95) [ 1237.953981] ? lockdep_init_map (kernel/locking/lockdep.c:3034) [ 1237.954967] blk_execute_rq (block/blk-exec.c:131) [ 1237.955929] ? blk_rq_bio_prep (block/blk-core.c:2835) [ 1237.956913] scsi_execute (drivers/scsi/scsi_lib.c:252) [ 1237.957821] scsi_execute_req_flags (drivers/scsi/scsi_lib.c:281) [ 1237.958968] scsi_report_opcode (drivers/scsi/scsi.c:956) [ 1237.960009] sd_revalidate_disk (drivers/scsi/sd.c:2707 drivers/scsi/sd.c:2792) [ 1237.961139] revalidate_disk (fs/block_dev.c:1081) [ 1237.962223] sd_rescan (drivers/scsi/sd.c:1532) [ 1237.963142] scsi_rescan_device (drivers/scsi/scsi_scan.c:1579) [ 1237.964165] store_rescan_field (drivers/scsi/scsi_sysfs.c:672) [ 1237.965254] dev_attr_store (drivers/base/core.c:138) [ 1237.966319] sysfs_kf_write (fs/sysfs/file.c:131) [ 1237.967289] kernfs_fop_write (fs/kernfs/file.c:311) [ 1237.968274] do_readv_writev (fs/read_write.c:722 fs/read_write.c:854) [ 1237.969295] ? __acct_update_integrals (kernel/tsacct.c:145) [ 1237.970452] ? kernfs_fop_open (fs/kernfs/file.c:271) [ 1237.971505] ? _raw_spin_unlock (./arch/x86/include/asm/preempt.h:95 include/linux/spinlock_api_smp.h:154 kernel/locking/spinlock.c:183) [ 1237.972512] ? context_tracking_user_exit (include/linux/vtime.h:89 include/linux/jump_label.h:114 include/trace/events/context_tracking.h:47 kernel/context_tracking.c:140) [ 1237.973668] ? trace_hardirqs_on_caller (kernel/locking/lockdep.c:2578 kernel/locking/lockdep.c:2625) [ 1237.974882] ? trace_hardirqs_on (kernel/locking/lockdep.c:2633) [ 1237.975850] vfs_writev (fs/read_write.c:893) [ 1237.976691] SyS_writev (fs/read_write.c:926 fs/read_write.c:917) [ 1237.977538] system_call_fastpath (arch/x86/kernel/entry_64.S:423) Signed-off-by: Sasha Levin <[email protected]> Acked-by: Douglas Gilbert <[email protected]> Signed-off-by: Christoph Hellwig <[email protected]>
2015-01-20ARM: dts: imx25: Fix PWM "per" clocksFabio Estevam1-4/+4
Currently PWM functionality is broken on mx25 due to the wrong assignment of the PWM "per" clock. According to Documentation/devicetree/bindings/clock/imx25-clock.txt: pwm_ipg_per 52 ,so update the pwm "per" to use 'pwm_ipg_per' instead of 'per10' clock. With this change PWM can work fine on mx25. Cc: <[email protected]> Reported-by: Carlos Soto <[email protected]> Signed-off-by: Fabio Estevam <[email protected]> Signed-off-by: Shawn Guo <[email protected]>
2015-01-20Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds31-192/+343
Pull networking fixes from David Miller: 1) Socket addresses returned in the error queue need to be fully initialized before being passed on to userspace, fix from Willem de Bruijn. 2) Interrupt handling fixes to davinci_emac driver from Tony Lindgren. 3) Fix races between receive packet steering and cpu hotplug, from Eric Dumazet. 4) Allowing netlink sockets to subscribe to unknown multicast groups leads to crashes, don't allow it. From Johannes Berg. 5) One to many socket races in SCTP fixed by Daniel Borkmann. 6) Put in a guard against the mis-use of ipv6 atomic fragments, from Hagen Paul Pfeifer. 7) Fix promisc mode and ethtool crashes in sh_eth driver, from Ben Hutchings. 8) NULL deref and double kfree fix in sxgbe driver from Girish K.S and Byungho An. 9) cfg80211 deadlock fix from Arik Nemtsov. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (36 commits) s2io: use snprintf() as a safety feature r8152: remove sram_read r8152: remove generic_ocp_read before writing bgmac: activate irqs only if there is nothing to poll bgmac: register napi before the device sh_eth: Fix ethtool operation crash when net device is down sh_eth: Fix promiscuous mode on chips without TSU ipv6: stop sending PTB packets for MTU < 1280 net: sctp: fix race for one-to-many sockets in sendmsg's auto associate genetlink: synchronize socket closing and family removal genetlink: disallow subscribing to unknown mcast groups genetlink: document parallel_ops net: rps: fix cpu unplug net: davinci_emac: Add support for emac on dm816x net: davinci_emac: Fix ioremap for devices with MDIO within the EMAC address space net: davinci_emac: Fix incomplete code for getting the phy from device tree net: davinci_emac: Free clock after checking the frequency net: davinci_emac: Fix runtime pm calls for davinci_emac net: davinci_emac: Fix hangs with interrupts ip: zero sockaddr returned on error queue ...
2015-01-20Merge git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6Linus Torvalds22-4/+27
Pull crypto fix from Herbert Xu: "This fixes a regression that arose from the change to add a crypto prefix to module names which was done to prevent the loading of arbitrary modules through the Crypto API. In particular, a number of modules were missing the crypto prefix which meant that they could no longer be autoloaded" * git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: crypto: add missing crypto module aliases
2015-01-20module: fix race in kallsyms resolution during module load success.Rusty Russell1-13/+42
The kallsyms routines (module_symbol_name, lookup_module_* etc) disable preemption to walk the modules rather than taking the module_mutex: this is because they are used for symbol resolution during oopses. This works because there are synchronize_sched() and synchronize_rcu() in the unload and failure paths. However, there's one case which doesn't have that: the normal case where module loading succeeds, and we free the init section. We don't want a synchronize_rcu() there, because it would slow down module loading: this bug was introduced in 2009 to speed module loading in the first place. Thus, we want to do the free in an RCU callback. We do this in the simplest possible way by allocating a new rcu_head: if we put it in the module structure we'd have to worry about that getting freed. Reported-by: Rui Xiang <[email protected]> Signed-off-by: Rusty Russell <[email protected]>
2015-01-20module: remove mod arg from module_free, rename module_memfree().Rusty Russell11-18/+18
Nothing needs the module pointer any more, and the next patch will call it from RCU, where the module itself might no longer exist. Removing the arg is the safest approach. This just codifies the use of the module_alloc/module_free pattern which ftrace and bpf use. Signed-off-by: Rusty Russell <[email protected]> Acked-by: Alexei Starovoitov <[email protected]> Cc: Mikael Starvik <[email protected]> Cc: Jesper Nilsson <[email protected]> Cc: Ralf Baechle <[email protected]> Cc: Ley Foon Tan <[email protected]> Cc: Benjamin Herrenschmidt <[email protected]> Cc: Chris Metcalf <[email protected]> Cc: Steven Rostedt <[email protected]> Cc: [email protected] Cc: Ananth N Mavinakayanahalli <[email protected]> Cc: Anil S Keshavamurthy <[email protected]> Cc: Masami Hiramatsu <[email protected]> Cc: [email protected] Cc: [email protected] Cc: [email protected] Cc: [email protected] Cc: [email protected] Cc: [email protected] Cc: [email protected]
2015-01-20module_arch_freeing_init(): new hook for archs before module->module_init freed.Rusty Russell7-29/+17
Archs have been abusing module_free() to clean up their arch-specific allocations. Since module_free() is also (ab)used by BPF and trace code, let's keep it to simple allocations, and provide a hook called before that. This means that avr32, ia64, parisc and s390 no longer need to implement their own module_free() at all. avr32 doesn't need module_finalize() either. Signed-off-by: Rusty Russell <[email protected]> Cc: Chris Metcalf <[email protected]> Cc: Haavard Skinnemoen <[email protected]> Cc: Hans-Christian Egtvedt <[email protected]> Cc: Tony Luck <[email protected]> Cc: Fenghua Yu <[email protected]> Cc: "James E.J. Bottomley" <[email protected]> Cc: Helge Deller <[email protected]> Cc: Martin Schwidefsky <[email protected]> Cc: Heiko Carstens <[email protected]> Cc: [email protected] Cc: [email protected] Cc: [email protected] Cc: [email protected]
2015-01-20param: fix uninitialized read with CONFIG_DEBUG_LOCK_ALLOCRusty Russell1-0/+1
ignore_lockdep is uninitialized, and sysfs_attr_init() doesn't initialize it, so memset to 0. Reported-by: Huang Ying <[email protected]> Cc: Eric W. Biederman <[email protected]> Signed-off-by: Rusty Russell <[email protected]>
2015-01-19s2io: use snprintf() as a safety featureDan Carpenter1-3/+8
"sp->desc[i]" has 25 characters. "dev->name" has 15 characters. If we used all 15 characters then the sprintf() would overflow. I changed the "sprintf(sp->name, "%s Neterion %s"" to snprintf(), as well, even though it can't overflow just to be consistent. Signed-off-by: Dan Carpenter <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2015-01-19Merge tag 'omap-for-v3.19/gic-regression-v2' of ↵Olof Johansson11-6/+77
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes Merge "Urgent omap4 legacy interrupt regression fix for v3.19-rc series" from Tony Lindgren: A rather urgent pull request to fix omap4 legacy interrupts. The legacy interrupts on omap4 got broken when gic got changed to use irq_domain_add_linear() instead of the irq_domain_add_legacy(). We still have the hardcoded legacy IRQ numbers in use in several places, most notably the in the legacy DMA. It took a while to figure out what the problem was and how it should be fixed for the -rc series. Also include is a regression fix for the dra7 dwc3 suspend. * tag 'omap-for-v3.19/gic-regression-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: ARM: OMAP: Work around hardcoded interrupts arm: boot: dts: dra7: enable dwc3 suspend PHY quirk Signed-off-by: Olof Johansson <[email protected]>
2015-01-19bus: mvebu-mbus: fix support of MBus window 13Andrew Lunn1-0/+13
On Armada XP, 375 and 38x the MBus window 13 has the remap capability, like windows 0 to 7. However, the mvebu-mbus driver isn't currently taking into account this special case, which means that when window 13 is actually used, the remap registers are left to 0, making the device using this MBus window unavailable. As a minimal fix for stable, don't use window 13. A full fix will follow later. Fixes: fddddb52a6c ("bus: introduce an Marvell EBU MBus driver") Cc: <[email protected]> # v3.10+ Reviewed-by: Thomas Petazzoni <[email protected]> Signed-off-by: Andrew Lunn <[email protected]>
2015-01-19Merge branch 'r8152'David S. Miller1-24/+6
Hayes Wang says: ==================== r8152: couldn't read OCP_SRAM_DATA Read OCP_SRAM_DATA would read additional bytes and may let the hw abnormal. ==================== Signed-off-by: David S. Miller <[email protected]>
2015-01-19r8152: remove sram_readhayeswang1-18/+6
Read OCP register 0xa43a~0xa43b would clear some flags which the hw would use, and it may let the device lost. However, the unit of reading is 4 bytes. That is, it would read 0xa438~0xa43b when calling sram_read() to read OCP_SRAM_DATA. Signed-off-by: Hayes Wang <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2015-01-19r8152: remove generic_ocp_read before writinghayeswang1-6/+0
For ocp_write_word() and ocp_write_byte(), there is a generic_ocp_read() which is used to read the whole 4 byte data, keep the unchanged bytes, and modify the expected bytes. However, the "byen" could be used to determine which bytes of the 4 bytes to write, so the action could be removed. Signed-off-by: Hayes Wang <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2015-01-19btrfs: fix state->private cast on 32 bit machinesSatoru Takeuchi1-1/+1
Suppress the following warning displayed on building 32bit (i686) kernel. =============================================================================== ... CC [M] fs/btrfs/extent_io.o fs/btrfs/extent_io.c: In function ‘btrfs_free_io_failure_record’: fs/btrfs/extent_io.c:2193:13: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast] failrec = (struct io_failure_record *)state->private; ... =============================================================================== Signed-off-by: Satoru Takeuchi <[email protected]> Reported-by: Chris Murphy <[email protected]> Signed-off-by: Chris Mason <[email protected]>
2015-01-19Btrfs: fix race deleting block group from space_info->ro_bgs listFilipe Manana2-1/+2
When removing a block group we were deleting it from its space_info's ro_bgs list without the correct protection - the space info's spinlock. Fix this by doing the list delete while holding the spinlock of the corresponding space info, which is the correct lock for any operation on that list. This issue was introduced in the 3.19 kernel by the following change: Btrfs: move read only block groups onto their own list V2 commit 633c0aad4c0243a506a3e8590551085ad78af82d I ran into a kernel crash while a task was running statfs, which iterates the space_info->ro_bgs list while holding the space info's spinlock, and another task was deleting it from the same list, without holding that spinlock, as part of the block group remove operation (while running the function btrfs_remove_block_group). This happened often when running the stress test xfstests/generic/038 I recently made. Signed-off-by: Filipe Manana <[email protected]> Signed-off-by: Chris Mason <[email protected]>
2015-01-19Btrfs: fix incorrect freeing in scrub_stripeTsutomu Itoh1-1/+1
The address that should be freed is not 'ppath' but 'path'. Signed-off-by: Tsutomu Itoh <[email protected]> Reviewed-by: Miao Xie <[email protected]> Signed-off-by: Chris Mason <[email protected]>
2015-01-19btrfs: sync ioctl, handle errors after transaction startDavid Sterba1-2/+2
The version merged to 3.19 did not handle errors from start_trancaction and could pass an invalid pointer to commit_transaction. Fixes: 6b5fe46dfa52441f ("btrfs: do commit in sync_fs if there are pending changes") Reported-by: Filipe Manana <[email protected]> Signed-off-by: David Sterba <[email protected]> Signed-off-by: Chris Mason <[email protected]>
2015-01-19Merge branch 'bgmac'David S. Miller1-6/+6
Hauke Mehrtens says: ==================== bgmac: some fixes to napi usage I compared the napi documentation with the bgmac driver and found some problems in that driver. These two patches should fix the problems. ==================== Signed-off-by: David S. Miller <[email protected]>
2015-01-19bgmac: activate irqs only if there is nothing to pollHauke Mehrtens1-3/+3
IRQs should only get activated when there is nothing to poll in the queue any more and to after every poll. Signed-off-by: Hauke Mehrtens <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2015-01-19bgmac: register napi before the deviceHauke Mehrtens1-3/+3
napi should get registered before the netdev and not after. Signed-off-by: Hauke Mehrtens <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2015-01-19Merge branch 'sh_eth'David S. Miller1-9/+19
Ben Hutchings says: ==================== sh_eth fixes I'm currently looking at Ethernet support on the R-Car H2 chip, reviewing and testing the sh_eth driver. Here are fixes for two fairly obvious bugs in the driver; I will probably have some more later. These are not tested on any of the other supported chips. ==================== Signed-off-by: David S. Miller <[email protected]>
2015-01-19sh_eth: Fix ethtool operation crash when net device is downBen Hutchings1-0/+10
The driver connects and disconnects the PHY device whenever the net device is brought up and down. The ethtool get_settings, set_settings and nway_reset operations will dereference a null or dangling pointer if called while it is down. I think it would be preferable to keep the PHY connected, but there may be good reasons not to. As an immediate fix for this bug: - Set the phydev pointer to NULL after disconnecting the PHY - Change those three operations to return -ENODEV while the PHY is not connected Signed-off-by: Ben Hutchings <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2015-01-19sh_eth: Fix promiscuous mode on chips without TSUBen Hutchings1-9/+9
Currently net_device_ops::set_rx_mode is only implemented for chips with a TSU (multiple address table). However we do need to turn the PRM (promiscuous) flag on and off for other chips. - Remove the unlikely() from the TSU functions that we may safely call for chips without a TSU - Make setting of the MCT flag conditional on the tsu capability flag - Rename sh_eth_set_multicast_list() to sh_eth_set_rx_mode() and plumb it into both net_device_ops structures - Remove the previously-unreachable branch in sh_eth_rx_mode() that would otherwise reset the flags to defaults for non-TSU chips Signed-off-by: Ben Hutchings <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2015-01-19ipv6: stop sending PTB packets for MTU < 1280Hagen Paul Pfeifer1-5/+2
Reduce the attack vector and stop generating IPv6 Fragment Header for paths with an MTU smaller than the minimum required IPv6 MTU size (1280 byte) - called atomic fragments. See IETF I-D "Deprecating the Generation of IPv6 Atomic Fragments" [1] for more information and how this "feature" can be misused. [1] https://tools.ietf.org/html/draft-ietf-6man-deprecate-atomfrag-generation-00 Signed-off-by: Fernando Gont <[email protected]> Signed-off-by: Hagen Paul Pfeifer <[email protected]> Acked-by: Hannes Frederic Sowa <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2015-01-19libata: prevent HSM state change race between ISR and PIODavid Jeffery1-0/+12
It is possible for ata_sff_flush_pio_task() to set ap->hsm_task_state to HSM_ST_IDLE in between the time __ata_sff_port_intr() checks for HSM_ST_IDLE and before it calls ata_sff_hsm_move() causing ata_sff_hsm_move() to BUG(). This problem is hard to reproduce making this patch hard to verify, but this fix will prevent the race. I have not been able to reproduce the problem, but here is a crash dump from a 2.6.32 kernel. On examining the ata port's state, its hsm_task_state field has a value of HSM_ST_IDLE: crash> struct ata_port.hsm_task_state ffff881c1121c000 hsm_task_state = 0 Normally, this should not be possible as ata_sff_hsm_move() was called from ata_sff_host_intr(), which checks hsm_task_state and won't call ata_sff_hsm_move() if it has a HSM_ST_IDLE value. PID: 11053 TASK: ffff8816e846cae0 CPU: 0 COMMAND: "sshd" #0 [ffff88008ba03960] machine_kexec at ffffffff81038f3b #1 [ffff88008ba039c0] crash_kexec at ffffffff810c5d92 #2 [ffff88008ba03a90] oops_end at ffffffff8152b510 #3 [ffff88008ba03ac0] die at ffffffff81010e0b #4 [ffff88008ba03af0] do_trap at ffffffff8152ad74 #5 [ffff88008ba03b50] do_invalid_op at ffffffff8100cf95 #6 [ffff88008ba03bf0] invalid_op at ffffffff8100bf9b [exception RIP: ata_sff_hsm_move+317] RIP: ffffffff813a77ad RSP: ffff88008ba03ca0 RFLAGS: 00010097 RAX: 0000000000000000 RBX: ffff881c1121dc60 RCX: 0000000000000000 RDX: ffff881c1121dd10 RSI: ffff881c1121dc60 RDI: ffff881c1121c000 RBP: ffff88008ba03d00 R8: 0000000000000000 R9: 000000000000002e R10: 000000000001003f R11: 000000000000009b R12: ffff881c1121c000 R13: 0000000000000000 R14: 0000000000000050 R15: ffff881c1121dd78 ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018 #7 [ffff88008ba03d08] ata_sff_host_intr at ffffffff813a7fbd #8 [ffff88008ba03d38] ata_sff_interrupt at ffffffff813a821e #9 [ffff88008ba03d78] handle_IRQ_event at ffffffff810e6ec0 --- <IRQ stack> --- [exception RIP: pipe_poll+48] RIP: ffffffff81192780 RSP: ffff880f26d459b8 RFLAGS: 00000246 RAX: 0000000000000000 RBX: ffff880f26d459c8 RCX: 0000000000000000 RDX: 0000000000000001 RSI: 0000000000000000 RDI: ffff881a0539fa80 RBP: ffffffff8100bb8e R8: ffff8803b23324a0 R9: 0000000000000000 R10: ffff880f26d45dd0 R11: 0000000000000008 R12: ffffffff8109b646 R13: ffff880f26d45948 R14: 0000000000000246 R15: 0000000000000246 ORIG_RAX: ffffffffffffff10 CS: 0010 SS: 0018 RIP: 00007f26017435c3 RSP: 00007fffe020c420 RFLAGS: 00000206 RAX: 0000000000000017 RBX: ffffffff8100b072 RCX: 00007fffe020c45c RDX: 00007f2604a3f120 RSI: 00007f2604a3f140 RDI: 000000000000000d RBP: 0000000000000000 R8: 00007fffe020e570 R9: 0101010101010101 R10: 0000000000000000 R11: 0000000000000246 R12: 00007fffe020e5f0 R13: 00007fffe020e5f4 R14: 00007f26045f373c R15: 00007fffe020e5e0 ORIG_RAX: 0000000000000017 CS: 0033 SS: 002b Somewhere between the ata_sff_hsm_move() check and the ata_sff_host_intr() check, the value changed. On examining the other cpus to see what else was running, another cpu was running the error handler routines: PID: 326 TASK: ffff881c11014aa0 CPU: 1 COMMAND: "scsi_eh_1" #0 [ffff88008ba27e90] crash_nmi_callback at ffffffff8102fee6 #1 [ffff88008ba27ea0] notifier_call_chain at ffffffff8152d515 #2 [ffff88008ba27ee0] atomic_notifier_call_chain at ffffffff8152d57a #3 [ffff88008ba27ef0] notify_die at ffffffff810a154e #4 [ffff88008ba27f20] do_nmi at ffffffff8152b1db #5 [ffff88008ba27f50] nmi at ffffffff8152aaa0 [exception RIP: _spin_lock_irqsave+47] RIP: ffffffff8152a1ff RSP: ffff881c11a73aa0 RFLAGS: 00000006 RAX: 0000000000000001 RBX: ffff881c1121deb8 RCX: 0000000000000000 RDX: 0000000000000246 RSI: 0000000000000020 RDI: ffff881c122612d8 RBP: ffff881c11a73aa0 R8: ffff881c17083800 R9: 0000000000000000 R10: 0000000000000000 R11: 0000000000000000 R12: ffff881c1121c000 R13: 000000000000001f R14: ffff881c1121dd50 R15: ffff881c1121dc60 ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0000 --- <NMI exception stack> --- #6 [ffff881c11a73aa0] _spin_lock_irqsave at ffffffff8152a1ff #7 [ffff881c11a73aa8] ata_exec_internal_sg at ffffffff81396fb5 #8 [ffff881c11a73b58] ata_exec_internal at ffffffff81397109 #9 [ffff881c11a73bd8] atapi_eh_request_sense at ffffffff813a34eb Before it tried to acquire a spinlock, ata_exec_internal_sg() called ata_sff_flush_pio_task(). This function will set ap->hsm_task_state to HSM_ST_IDLE, and has no locking around setting this value. ata_sff_flush_pio_task() can then race with the interrupt handler and potentially set HSM_ST_IDLE at a fatal moment, which will trigger a kernel BUG. v2: Fixup comment in ata_sff_flush_pio_task() tj: Further updated comment. Use ap->lock instead of shost lock and use the [un]lock_irq variant instead of the irqsave/restore one. Signed-off-by: David Milburn <[email protected]> Signed-off-by: Tejun Heo <[email protected]> Cc: [email protected]
2015-01-19scripts/recordmcount.pl: There is no -m32 gcc option on Super-H anymoreMichael Karcher1-1/+0
Compiling SH with gcc-4.8 fails due to the -m32 option not being supported. From http://buildd.debian-ports.org/status/fetch.php?pkg=linux&arch=sh4&ver=3.16.7-ckt4-1&stamp=1421425783 CC init/main.o gcc-4.8: error: unrecognized command line option '-m32' ld: cannot find init/.tmp_mc_main.o: No such file or directory objcopy: 'init/.tmp_mx_main.o': No such file rm: cannot remove 'init/.tmp_mx_main.o': No such file or directory rm: cannot remove 'init/.tmp_mc_main.o': No such file or directory Link: http://lkml.kernel.org/r/1421537778-29001-1-git-send-email-kernel@mkarcher.dialup.fu-berlin.de Link: http://lkml.kernel.org/r/[email protected] Cc: [email protected] Cc: Matt Fleming <[email protected]> Reported-by: John Paul Adrian Glaubitz <[email protected]> Signed-off-by: Michael Karcher <[email protected]> Signed-off-by: Steven Rostedt <[email protected]>
2015-01-19libata: allow sata_sil24 to opt-out of tag ordered submissionDan Williams3-2/+6
Ronny reports: https://bugzilla.kernel.org/show_bug.cgi?id=87101 "Since commit 8a4aeec8d "libata/ahci: accommodate tag ordered controllers" the access to the harddisk on the first SATA-port is failing on its first access. The access to the harddisk on the second port is working normal. When reverting the above commit, access to both harddisks is working fine again." Maintain tag ordered submission as the default, but allow sata_sil24 to continue with the old behavior. Cc: <[email protected]> Cc: Tejun Heo <[email protected]> Reported-by: Ronny Hegewald <[email protected]> Signed-off-by: Dan Williams <[email protected]> Signed-off-by: Tejun Heo <[email protected]>
2015-01-19pinctrl: MAINTAINERS: add git tree referenceLinus Walleij1-0/+1
Reference my pinctrl GIT tree @kernel.org Reported-by: Sergei Shtylyov <[email protected]> Signed-off-by: Linus Walleij <[email protected]>
2015-01-19pinctrl: qcom: Don't iterate past end of function arrayStephen Boyd1-2/+2
Timur reports that this code crashes if nfunctions is 0. Fix the loop iteration to only consider valid elements of the functions array. Reported-by: Timur Tabi <[email protected]> Cc: Pramod Gurav <[email protected]> Cc: Bjorn Andersson <[email protected]> Cc: Ivan T. Ivanov <[email protected]> Cc: Andy Gross <[email protected]> Fixes: 327455817a92 "pinctrl: qcom: Add support for reset for apq8064" Signed-off-by: Stephen Boyd <[email protected]> Signed-off-by: Linus Walleij <[email protected]>
2015-01-19KVM: fix sparse warning in include/trace/events/kvm.hChristian Borntraeger1-7/+9
sparse complains about include/trace/events/kvm.h:163:1: error: directive in argument list include/trace/events/kvm.h:167:1: error: directive in argument list include/trace/events/kvm.h:169:1: error: directive in argument list and sparse is right. Preprocessing directives in an argument of a macro are undefined behaviour as of C99 6.10.3p11. Lets use an indirection to fix this. Signed-off-by: Christian Borntraeger <[email protected]> Signed-off-by: Paolo Bonzini <[email protected]>
2015-01-19ipr: wait for aborted command responsesBrian King2-0/+93
Fixes a race condition in abort handling that was injected when multiple interrupt support was added. When only a single interrupt is present, the adapter guarantees it will send responses for aborted commands prior to the response for the abort command itself. With multiple interrupts, these responses generally come back on different interrupts, so we need to ensure the abort thread waits until the aborted command is complete so we don't perform a double completion. This race condition was being hit frequently in environments which were triggering command timeouts, which was resulting in a double completion causing a kernel oops. Cc: <[email protected]> Signed-off-by: Brian King <[email protected]> Reviewed-by: Wendy Xiong <[email protected]> Tested-by: Wendy Xiong <[email protected]> Signed-off-by: Christoph Hellwig <[email protected]>
2015-01-18fix deadlock in cifs_ioctl_clone()Al Viro1-16/+5
It really needs to check that src is non-directory *and* use {un,}lock_two_nodirectories(). As it is, it's trivial to cause double-lock (ioctl(fd, CIFS_IOC_COPYCHUNK_FILE, fd)) and if the last argument is an fd of directory, we are asking for trouble by violating the locking order - all directories go before all non-directories. If the last argument is an fd of parent directory, it has 50% odds of locking child before parent, which will cause AB-BA deadlock if we race with unlink(). Cc: [email protected] @ 3.13+ Signed-off-by: Al Viro <[email protected]>
2015-01-18Merge tag 'mvebu-fixes-3.19-3' of git://git.infradead.org/linux-mvebu into fixesOlof Johansson1-1/+6
Merge " mvebu fixes for 3.19-rc (part #3)" from Andrew Lunn: mvebu: completely disable hardware I/O coherency * tag 'mvebu-fixes-3.19-3' of git://git.infradead.org/linux-mvebu: ARM: mvebu: completely disable hardware I/O coherency Signed-off-by: Olof Johansson <[email protected]>
2015-01-19Merge tag 'gpio-v3.19-4' of ↵Linus Torvalds5-71/+92
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio Pull GPIO fixes from Linus Walleij: "Here is a set of fixes that mainly appeared when Johan Hovold started exercising the removal path of the GPIO library, dealing with hotplugging of GPIO controllers. Details from tag: A slew of fixes dealing with some irritating bugs (non-regressions) that have been around forever in the GPIO subsystem, most of them also tagged for stable: - A large slew of fixes from Johan Hovold who is finally testing and reviewing the removal path of the GPIO drivers. - Fix of_get_named_gpiod_flags() so it works as expected. - Fix an IRQ handling bug in the crystalcove driver" * tag 'gpio-v3.19-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: gpiolib: of: Correct error handling in of_get_named_gpiod_flags gpio: sysfs: fix gpio attribute-creation race gpio: sysfs: fix gpio device-attribute leak gpio: sysfs: fix gpio-chip device-attribute leak gpio: unregister gpiochip device before removing it gpio: fix sleep-while-atomic in gpiochip_remove gpio: fix memory leak and sleep-while-atomic gpio: clean up gpiochip_add error handling gpio: fix gpio-chip list corruption gpio: fix memory and reference leaks in gpiochip_add error path gpio: crystalcove: use handle_nested_irq
2015-01-19Merge branch 'for-linus' of ↵Linus Torvalds6-3/+58
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input Pull input subsystem fixes from Dmitry Torokhov. * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: Input: uinput - fix ioctl nr overflow for UI_GET_SYSNAME/VERSION Input: I8042 - add Acer Aspire 7738 to the nomux list Input: elantech - support new ICs types for version 4 Input: i8042 - reset keyboard to fix Elantech touchpad detection MAINTAINERS: remove Dmitry Torokhov's alternate address
2015-01-18ALSA: usb-audio: Add mic volume fix quirk for Logitech Webcam C210Jason Lee Cragg1-0/+1
Signed-off-by: Jason Lee Cragg <[email protected]> Cc: <[email protected]> Signed-off-by: Takashi Iwai <[email protected]>
2015-01-18drm/exynos: fix warning of vblank reference countJoonyoung Shim1-1/+6
Prevented re-enabling the vblank interrupt by drm_vblank_off and drm_vblank_get from mixer_wait_for_vblank returns error after drm_vblank_off. We get below warnings without this error handling because vblank reference count is mismatched by above sequence. setting mode 1920x1080-60Hz@XR24 on connectors 16, crtc 13 [ 19.900793] ------------[ cut here ]------------ [ 19.903959] WARNING: CPU: 0 PID: 0 at drivers/gpu/drm/drm_irq.c:1072 exynos_drm_crtc_finish_pageflip+0xac/0xdc() [ 19.914076] Modules linked in: [ 19.917116] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.19.0-rc4-00040-g3d729789-dirty #46 [ 19.925342] Hardware name: SAMSUNG EXYNOS (Flattened Device Tree) [ 19.931437] [<c0014430>] (unwind_backtrace) from [<c001158c>] (show_stack+0x10/0x14) [ 19.939131] [<c001158c>] (show_stack) from [<c04cdd50>] (dump_stack+0x84/0xc4) [ 19.946329] [<c04cdd50>] (dump_stack) from [<c00226f4>] (warn_slowpath_common+0x80/0xb0) [ 19.954382] [<c00226f4>] (warn_slowpath_common) from [<c00227c0>] (warn_slowpath_null+0x1c/0x24) [ 19.963132] [<c00227c0>] (warn_slowpath_null) from [<c02c20cc>] (exynos_drm_crtc_finish_pageflip+0xac/0xdc) [ 19.972841] [<c02c20cc>] (exynos_drm_crtc_finish_pageflip) from [<c02cb7ec>] (mixer_irq_handler+0xdc/0x104) [ 19.982546] [<c02cb7ec>] (mixer_irq_handler) from [<c005c904>] (handle_irq_event_percpu+0x78/0x134) [ 19.991555] [<c005c904>] (handle_irq_event_percpu) from [<c005c9fc>] (handle_irq_event+0x3c/0x5c) [ 20.000395] [<c005c9fc>] (handle_irq_event) from [<c005f384>] (handle_fasteoi_irq+0xe0/0x1ac) [ 20.008885] [<c005f384>] (handle_fasteoi_irq) from [<c005bf88>] (generic_handle_irq+0x2c/0x3c) [ 20.017463] [<c005bf88>] (generic_handle_irq) from [<c005c254>] (__handle_domain_irq+0x7c/0xec) [ 20.026128] [<c005c254>] (__handle_domain_irq) from [<c0008698>] (gic_handle_irq+0x30/0x68) [ 20.034449] [<c0008698>] (gic_handle_irq) from [<c00120c0>] (__irq_svc+0x40/0x74) [ 20.041893] Exception stack(0xc06fff68 to 0xc06fffb0) [ 20.046923] ff60: 00000000 00000000 000052f6 c001b460 c06fe000 c07064e8 [ 20.055070] ff80: c04d743c c07392a2 c0739440 c06da340 ef7fca80 00000000 01000000 c06fffb0 [ 20.063212] ffa0: c000f24c c000f250 60000013 ffffffff [ 20.068245] [<c00120c0>] (__irq_svc) from [<c000f250>] (arch_cpu_idle+0x38/0x3c) [ 20.075611] [<c000f250>] (arch_cpu_idle) from [<c0050948>] (cpu_startup_entry+0x108/0x16c) [ 20.083846] [<c0050948>] (cpu_startup_entry) from [<c06aec5c>] (start_kernel+0x3a0/0x3ac) [ 20.091980] ---[ end trace 2c76ee0500489d1b ]--- Signed-off-by: Joonyoung Shim <[email protected]> Signed-off-by: Inki Dae <[email protected]>
2015-01-18drm/exynos: remove unnecessary runtime pm operationsJoonyoung Shim1-4/+0
In booting, we can see a below message. [ 3.241728] exynos-mixer 14450000.mixer: Unbalanced pm_runtime_enable! Already pm_runtime_enable is called by probe function. Remove pm_runtime_enable/disable from mixer_bind and mixer_unbind. Signed-off-by: Joonyoung Shim <[email protected]> Signed-off-by: Inki Dae <[email protected]>
2015-01-18drm/exynos: fix reset codes for memory mapped hdmi phyJoonyoung Shim1-6/+2
This fixes reset codes to support memory mapped hdmi phy as well as hdmi phy dedicated i2c lines. Signed-off-by: Joonyoung Shim <[email protected]> Signed-off-by: Inki Dae <[email protected]>
2015-01-18Linux 3.19-rc5Linus Torvalds1-1/+1
2015-01-18Merge tag 'armsoc-for-linus' of ↵Linus Torvalds32-80/+272
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC fixes from Olof Johansson: "We've been sitting on our fixes branch for a while, so this batch is unfortunately on the large side. A lot of these are tweaks and fixes to device trees, fixing various bugs around clocks, reg ranges, etc. There's also a few defconfig updates (which are on the late side, no more of those). All in all the diffstat is bigger than ideal at this time, but nothing in here seems particularly risky" * tag 'armsoc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (31 commits) reset: sunxi: fix spinlock initialization ARM: dts: disable CCI on exynos5420 based arndale-octa drivers: bus: check cci device tree node status ARM: rockchip: disable jtag/sdmmc autoswitching on rk3288 ARM: nomadik: fix up leftover device tree pins ARM: at91: board-dt-sama5: add phy_fixup to override NAND_Tree ARM: at91/dt: sam9263: Add missing clocks to lcdc node ARM: at91: sama5d3: dt: correct the sound route ARM: at91/dt: sama5d4: fix the timer reg length ARM: exynos_defconfig: Enable LM90 driver ARM: exynos_defconfig: Enable options for display panel support arm: dts: Use pmu_system_controller phandle for dp phy ARM: shmobile: sh73a0 legacy: Set .control_parent for all irqpin instances ARM: dts: berlin: correct BG2Q's SM GPIO location. ARM: dts: berlin: add broken-cd and set bus width for eMMC in Marvell DMP DT ARM: dts: berlin: fix io clk and add missing core clk for BG2Q sdhci2 host ARM: dts: Revert disabling of smc91x for n900 ARM: dts: imx51-babbage: Fix ULPI PHY reset modelling ARM: dts: dra7-evm: fix qspi device tree partition size ARM: omap2plus_defconfig: use CONFIG_CPUFREQ_DT ...
2015-01-17net: sctp: fix race for one-to-many sockets in sendmsg's auto associateDaniel Borkmann1-1/+7
I.e. one-to-many sockets in SCTP are not required to explicitly call into connect(2) or sctp_connectx(2) prior to data exchange. Instead, they can directly invoke sendmsg(2) and the SCTP stack will automatically trigger connection establishment through 4WHS via sctp_primitive_ASSOCIATE(). However, this in its current implementation is racy: INIT is being sent out immediately (as it cannot be bundled anyway) and the rest of the DATA chunks are queued up for later xmit when connection is established, meaning sendmsg(2) will return successfully. This behaviour can result in an undesired side-effect that the kernel made the application think the data has already been transmitted, although none of it has actually left the machine, worst case even after close(2)'ing the socket. Instead, when the association from client side has been shut down e.g. first gracefully through SCTP_EOF and then close(2), the client could afterwards still receive the server's INIT_ACK due to a connection with higher latency. This INIT_ACK is then considered out of the blue and hence responded with ABORT as there was no alive assoc found anymore. This can be easily reproduced f.e. with sctp_test application from lksctp. One way to fix this race is to wait for the handshake to actually complete. The fix defers waiting after sctp_primitive_ASSOCIATE() and sctp_primitive_SEND() succeeded, so that DATA chunks cooked up from sctp_sendmsg() have already been placed into the output queue through the side-effect interpreter, and therefore can then be bundeled together with COOKIE_ECHO control chunks. strace from example application (shortened): socket(PF_INET, SOCK_SEQPACKET, IPPROTO_SCTP) = 3 sendmsg(3, {msg_name(28)={sa_family=AF_INET, sin_port=htons(8888), sin_addr=inet_addr("192.168.1.115")}, msg_iov(1)=[{"hello", 5}], msg_controllen=0, msg_flags=0}, 0) = 5 sendmsg(3, {msg_name(28)={sa_family=AF_INET, sin_port=htons(8888), sin_addr=inet_addr("192.168.1.115")}, msg_iov(1)=[{"hello", 5}], msg_controllen=0, msg_flags=0}, 0) = 5 sendmsg(3, {msg_name(28)={sa_family=AF_INET, sin_port=htons(8888), sin_addr=inet_addr("192.168.1.115")}, msg_iov(1)=[{"hello", 5}], msg_controllen=0, msg_flags=0}, 0) = 5 sendmsg(3, {msg_name(28)={sa_family=AF_INET, sin_port=htons(8888), sin_addr=inet_addr("192.168.1.115")}, msg_iov(1)=[{"hello", 5}], msg_controllen=0, msg_flags=0}, 0) = 5 sendmsg(3, {msg_name(28)={sa_family=AF_INET, sin_port=htons(8888), sin_addr=inet_addr("192.168.1.115")}, msg_iov(0)=[], msg_controllen=48, {cmsg_len=48, cmsg_level=0x84 /* SOL_??? */, cmsg_type=, ...}, msg_flags=0}, 0) = 0 // graceful shutdown for SOCK_SEQPACKET via SCTP_EOF close(3) = 0 tcpdump before patch (fooling the application): 22:33:36.306142 IP 192.168.1.114.41462 > 192.168.1.115.8888: sctp (1) [INIT] [init tag: 3879023686] [rwnd: 106496] [OS: 10] [MIS: 65535] [init TSN: 3139201684] 22:33:36.316619 IP 192.168.1.115.8888 > 192.168.1.114.41462: sctp (1) [INIT ACK] [init tag: 3345394793] [rwnd: 106496] [OS: 10] [MIS: 10] [init TSN: 3380109591] 22:33:36.317600 IP 192.168.1.114.41462 > 192.168.1.115.8888: sctp (1) [ABORT] tcpdump after patch: 14:28:58.884116 IP 192.168.1.114.35846 > 192.168.1.115.8888: sctp (1) [INIT] [init tag: 438593213] [rwnd: 106496] [OS: 10] [MIS: 65535] [init TSN: 3092969729] 14:28:58.888414 IP 192.168.1.115.8888 > 192.168.1.114.35846: sctp (1) [INIT ACK] [init tag: 381429855] [rwnd: 106496] [OS: 10] [MIS: 10] [init TSN: 2141904492] 14:28:58.888638 IP 192.168.1.114.35846 > 192.168.1.115.8888: sctp (1) [COOKIE ECHO] , (2) [DATA] (B)(E) [TSN: 3092969729] [...] 14:28:58.893278 IP 192.168.1.115.8888 > 192.168.1.114.35846: sctp (1) [COOKIE ACK] , (2) [SACK] [cum ack 3092969729] [a_rwnd 106491] [#gap acks 0] [#dup tsns 0] 14:28:58.893591 IP 192.168.1.114.35846 > 192.168.1.115.8888: sctp (1) [DATA] (B)(E) [TSN: 3092969730] [...] 14:28:59.096963 IP 192.168.1.115.8888 > 192.168.1.114.35846: sctp (1) [SACK] [cum ack 3092969730] [a_rwnd 106496] [#gap acks 0] [#dup tsns 0] 14:28:59.097086 IP 192.168.1.114.35846 > 192.168.1.115.8888: sctp (1) [DATA] (B)(E) [TSN: 3092969731] [...] , (2) [DATA] (B)(E) [TSN: 3092969732] [...] 14:28:59.103218 IP 192.168.1.115.8888 > 192.168.1.114.35846: sctp (1) [SACK] [cum ack 3092969732] [a_rwnd 106486] [#gap acks 0] [#dup tsns 0] 14:28:59.103330 IP 192.168.1.114.35846 > 192.168.1.115.8888: sctp (1) [SHUTDOWN] 14:28:59.107793 IP 192.168.1.115.8888 > 192.168.1.114.35846: sctp (1) [SHUTDOWN ACK] 14:28:59.107890 IP 192.168.1.114.35846 > 192.168.1.115.8888: sctp (1) [SHUTDOWN COMPLETE] Looks like this bug is from the pre-git history museum. ;) Fixes: 08707d5482df ("lksctp-2_5_31-0_5_1.patch") Signed-off-by: Daniel Borkmann <[email protected]> Acked-by: Vlad Yasevich <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2015-01-18Merge tag 'clk-fixes-for-linus' of ↵Linus Torvalds7-28/+69
git://git.linaro.org/people/mike.turquette/linux Pull clock driver fixes from Mike Turquette: "Small number of fixes for clock drivers and a single null pointer dereference fix in the framework core code. The driver fixes vary from fixing section mismatch warnings to preventing machines from hanging (and preventing developers from crying)" * tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux: clk: fix possible null pointer dereference Revert "clk: ppc-corenet: Fix Section mismatch warning" clk: rockchip: fix deadlock possibility in cpuclk clk: berlin: bg2q: remove non-exist "smemc" gate clock clk: at91: keep slow clk enabled to prevent system hang clk: rockchip: fix rk3288 cpuclk core dividers clk: rockchip: fix rk3066 pll lock bit location clk: rockchip: Fix clock gate for rk3188 hclk_emem_peri clk: rockchip: add CLK_IGNORE_UNUSED flag to fix rk3066/rk3188 USB Host
2015-01-18Merge tag 'scsi-fixes' of ↵Linus Torvalds2-4/+2
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi Pull SCSI fixes from James Bottomley: "This is one fix for a Multiqueue sleeping in invalid context problem and a MAINTAINER file update for Qlogic" * tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: scsi: ->queue_rq can't sleep MAINTAINERS: Update maintainer list for qla4xxx
Powered by cgit, Gruvboxed by Blaster4385.