| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Since IIO framework supports device property API and driver has been moved
already to the use of GPIO descriptors the logical continuation is to
get rid of platform data completely. We are on the safe side here since
there are no users of it in the kernel.
Signed-off-by: Andy Shevchenko <[email protected]>
Signed-off-by: Jonathan Cameron <[email protected]>
|
|
Ad7124 data-sheet specifies that the falling edge
of the DOUT line should be used for an interrupt.
The current irq flag (IRQF_TRIGGER_LOW) used will
cause unwanted behaviour. When enabling the interrupt
it will fire once because the DOUT line is already low.
This will make the driver to read an unfinished conversion
from the chip.
This patch sets the irq type to the one specified in
the data-sheet.
Signed-off-by: Alexandru Tachici <[email protected]>
Signed-off-by: Jonathan Cameron <[email protected]>
|
|
Before this patch the ad_sigma_delta implementation hardcoded
the irq trigger type to low, assuming that all Sigma-Delta ADCs
have the same interrupt-type.
This patch allows all drivers using the ad_sigma_delta layer to set the
irq trigger type to the one specified in the datasheet.
Signed-off-by: Alexandru Tachici <[email protected]>
Signed-off-by: Jonathan Cameron <[email protected]>
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
virtio: maintain obj reservation lock when submitting cmds (Gerd)
rockchip: increase link rate var size to accommodate rates (Tobias)
mst: serialize down messages and clear timeslots are on unplug (Wayne)
Cc: Gerd Hoffmann <[email protected]>
Cc: Tobias Schramm <[email protected]>
Cc: Wayne Lin <[email protected]>
Signed-off-by: Dave Airlie <[email protected]>
From: Sean Paul <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/20200116162856.GA11524@art_vandelay
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
- uAPI fix: Remove dash and colon from PMU names to comply with tools/perf
- Fix for include file that was indirectly included
- Two fixes to make sure VMA are marked active for error capture
Signed-off-by: Dave Airlie <[email protected]>
From: Joonas Lahtinen <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]
|
|
As we reset the GPMI block at resume, the timing parameters setup by a
previous exec_op is lost. Rewriting GPMI timing registers on first exec_op
after resume fixes the problem.
Fixes: ef347c0cfd61 ("mtd: rawnand: gpmi: Implement exec_op")
Cc: [email protected]
Signed-off-by: Esben Haabendal <[email protected]>
Acked-by: Han Xu <[email protected]>
Signed-off-by: Miquel Raynal <[email protected]>
|
|
On system resume, the gpmi clock must be enabled before accessing gpmi
block. Without this, resume causes something like
[ 661.348790] gpmi_reset_block(5cbb0f7e): module reset timeout
[ 661.348889] gpmi-nand 1806000.gpmi-nand: Error setting GPMI : -110
[ 661.348928] PM: dpm_run_callback(): platform_pm_resume+0x0/0x44 returns -110
[ 661.348961] PM: Device 1806000.gpmi-nand failed to resume: error -110
Fixes: ef347c0cfd61 ("mtd: rawnand: gpmi: Implement exec_op")
Cc: [email protected]
Signed-off-by: Esben Haabendal <[email protected]>
Acked-by: Han Xu <[email protected]>
Signed-off-by: Miquel Raynal <[email protected]>
|
|
The commit 7b678c69c0ca ("mtd: spi-nor: Merge spansion Quad Enable
methods") forgot to actually set the QE bit in some cases. Thus this
breaks quad mode accesses to flashes which support readback of the
status register-2. Fix it.
Fixes: 7b678c69c0ca ("mtd: spi-nor: Merge spansion Quad Enable methods")
Signed-off-by: Michael Walle <[email protected]>
Reviewed-by: Tudor Ambarus <[email protected]>
Signed-off-by: Miquel Raynal <[email protected]>
|
|
mtd->size is still unassigned when running spansion_post_sfdp_fixups()
hook, therefore use nor->params.size to determine the size of flash device.
This makes sure that 4-byte addressing opcodes are used on Spansion
flashes that are larger than 16MiB and don't have SFDP 4BAIT table
populated.
Fixes: 92094ebc385e ("mtd: spi-nor: Add spansion_post_sfdp_fixups()")
Signed-off-by: Vignesh Raghavendra <[email protected]>
Reviewed-by: Tudor Ambarus <[email protected]>
Signed-off-by: Miquel Raynal <[email protected]>
|
|
Pull io_uring fixes form Jens Axboe:
- Ensure ->result is always set when IO is retried (Bijan)
- In conjunction with the above, fix a regression in polled IO issue
when retried (me/Bijan)
- Don't setup async context for read/write fixed, otherwise we may
wrongly map the iovec on retry (me)
- Cancel io-wq work if we fail getting mm reference (me)
- Ensure dependent work is always initialized correctly (me)
- Only allow original task to submit IO, don't allow it from a passed
ring fd (me)
* tag 'io_uring-5.5-2020-01-16' of git://git.kernel.dk/linux-block:
io_uring: only allow submit from owning task
io_uring: ensure workqueue offload grabs ring mutex for poll list
io_uring: clear req->result always before issuing a read/write request
io_uring: be consistent in assigning next work from handler
io-wq: cancel work if we fail getting a mm reference
io_uring: don't setup async context for read/write fixed
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"A few more fixes that have been in the works during last twp weeks.
All have a user visible effect and are stable material:
- scrub: properly update progress after calling cancel ioctl, calling
'resume' would start from the beginning otherwise
- fix subvolume reference removal, after moving out of the original
path the reference is not recognized and will lead to transaction
abort
- fix reloc root lifetime checks, could lead to crashes when there's
subvolume cleaning running in parallel
- fix memory leak when quotas get disabled in the middle of extent
accounting
- fix transaction abort in case of balance being started on degraded
mount on eg. RAID1"
* tag 'for-5.5-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: check rw_devices, not num_devices for balance
Btrfs: always copy scrub arguments back to user space
btrfs: relocation: fix reloc_root lifespan and access
btrfs: fix memory leak in qgroup accounting
btrfs: do not delete mismatched root refs
btrfs: fix invalid removal of root ref
btrfs: rework arguments of btrfs_unlink_subvol
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.5-rc7
Here are a few fixes for issues related to unbound port devices which
could lead to NULL-pointer dereferences. Notably the bind attributes for
usb-serial (port) drivers are removed as almost none of the drivers can
handle individual ports going away once they've been bound.
Included are also some new device ids.
All but the unbound-port fixes have been in linux-next with no reported
issues.
Signed-off-by: Johan Hovold <[email protected]>
* tag 'usb-serial-5.5-rc7' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: quatech2: handle unbound ports
USB: serial: keyspan: handle unbound ports
USB: serial: io_edgeport: add missing active-port sanity check
USB: serial: io_edgeport: handle unbound ports on URB completion
USB: serial: ch341: handle unbound port at reset_resume
USB: serial: suppress driver bind attributes
USB: serial: option: add support for Quectel RM500Q in QDL mode
USB: serial: opticon: fix control-message timeouts
USB: serial: option: Add support for Quectel RM500Q
USB: serial: simple: Add Motorola Solutions TETRA MTP3xxx and MTP85xx
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse
Pull fuse fix from Miklos Szeredi:
"Fix a regression in the last release affecting the ftp module of the
gvfs filesystem"
* tag 'fuse-fixes-5.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: fix fuse_send_readpages() in the syncronous read case
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This became bigger than I have hoped for rc7. But, the only large LOC
is for stm32 fixes that are simple rewriting of register access
helpers, while the rest are all nice and small fixes:
- A few ASoC fixes for the remaining probe error handling bugs
- ALSA sequencer core fix for racy proc file accesses
- Revert the option rename of snd-hda-intel to make compatible again
- Various device-specific fixes"
* tag 'sound-5.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: seq: Fix racy access for queue timer in proc read
ALSA: usb-audio: fix sync-ep altsetting sanity check
ASoC: msm8916-wcd-digital: Reset RX interpolation path after use
ASoC: msm8916-wcd-analog: Fix MIC BIAS Internal1
ASoC: cros_ec_codec: Make the device acpi compatible
ASoC: sti: fix possible sleep-in-atomic
ASoC: msm8916-wcd-analog: Fix selected events for MIC BIAS External1
ASoC: hdac_hda: Fix error in driver removal after failed probe
ASoC: SOF: Intel: fix HDA codec driver probe with multiple controllers
ASoC: SOF: Intel: lower print level to dbg if we will reinit DSP
ALSA: dice: fix fallback from protocol extension into limited functionality
ALSA: firewire-tascam: fix corruption due to spin lock without restoration in SoftIRQ context
ALSA: hda: Rename back to dmic_detect option
ASoC: stm32: dfsdm: fix 16 bits record
ASoC: stm32: sai: fix possible circular locking
ASoC: Fix NULL dereference at freeing
ASoC: Intel: bytcht_es8316: Fix Irbis NB41 netbook quirk
ASoC: rt5640: Fix NULL dereference on module unload
|
|
Check for NULL port data in the modem- and line-status handlers to avoid
dereferencing a NULL pointer in the unlikely case where a port device
isn't bound to a driver (e.g. after an allocation failure on port
probe).
Note that the other (stubbed) event handlers qt2_process_xmit_empty()
and qt2_process_flush() would need similar sanity checks in case they
are ever implemented.
Fixes: f7a33e608d9a ("USB: serial: add quatech2 usb to serial driver")
Cc: stable <[email protected]> # 3.5
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
Check for NULL port data in the control URB completion handlers to avoid
dereferencing a NULL pointer in the unlikely case where a port device
isn't bound to a driver (e.g. after an allocation failure on port
probe()).
Fixes: 0ca1268e109a ("USB Serial Keyspan: add support for USA-49WG & USA-28XG")
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable <[email protected]>
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
The driver receives the active port number from the device, but never
made sure that the port number was valid. This could lead to a
NULL-pointer dereference or memory corruption in case a device sends
data for an invalid port.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable <[email protected]>
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
Check for NULL port data in the shared interrupt and bulk completion
callbacks to avoid dereferencing a NULL pointer in case a device sends
data for a port device which isn't bound to a driver (e.g. due to a
malicious device having unexpected endpoints or after an allocation
failure on port probe).
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable <[email protected]>
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
Check for NULL port data in reset_resume() to avoid dereferencing a NULL
pointer in case the port device isn't bound to a driver (e.g. after a
failed control request at port probe).
Fixes: 1ded7ea47b88 ("USB: ch341 serial: fix port number changed after resume")
Cc: stable <[email protected]> # 2.6.30
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
The fstest btrfs/154 reports
[ 8675.381709] BTRFS: Transaction aborted (error -28)
[ 8675.383302] WARNING: CPU: 1 PID: 31900 at fs/btrfs/block-group.c:2038 btrfs_create_pending_block_groups+0x1e0/0x1f0 [btrfs]
[ 8675.390925] CPU: 1 PID: 31900 Comm: btrfs Not tainted 5.5.0-rc6-default+ #935
[ 8675.392780] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.0-59-gc9ba527-rebuilt.opensuse.org 04/01/2014
[ 8675.395452] RIP: 0010:btrfs_create_pending_block_groups+0x1e0/0x1f0 [btrfs]
[ 8675.402672] RSP: 0018:ffffb2090888fb00 EFLAGS: 00010286
[ 8675.404413] RAX: 0000000000000000 RBX: ffff92026dfa91c8 RCX: 0000000000000001
[ 8675.406609] RDX: 0000000000000000 RSI: ffffffff8e100899 RDI: ffffffff8e100971
[ 8675.408775] RBP: ffff920247c61660 R08: 0000000000000000 R09: 0000000000000000
[ 8675.410978] R10: 0000000000000000 R11: 0000000000000000 R12: 00000000ffffffe4
[ 8675.412647] R13: ffff92026db74000 R14: ffff920247c616b8 R15: ffff92026dfbc000
[ 8675.413994] FS: 00007fd5e57248c0(0000) GS:ffff92027d800000(0000) knlGS:0000000000000000
[ 8675.416146] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 8675.417833] CR2: 0000564aa51682d8 CR3: 000000006dcbc004 CR4: 0000000000160ee0
[ 8675.419801] Call Trace:
[ 8675.420742] btrfs_start_dirty_block_groups+0x355/0x480 [btrfs]
[ 8675.422600] btrfs_commit_transaction+0xc8/0xaf0 [btrfs]
[ 8675.424335] reset_balance_state+0x14a/0x190 [btrfs]
[ 8675.425824] btrfs_balance.cold+0xe7/0x154 [btrfs]
[ 8675.427313] ? kmem_cache_alloc_trace+0x235/0x2c0
[ 8675.428663] btrfs_ioctl_balance+0x298/0x350 [btrfs]
[ 8675.430285] btrfs_ioctl+0x466/0x2550 [btrfs]
[ 8675.431788] ? mem_cgroup_charge_statistics+0x51/0xf0
[ 8675.433487] ? mem_cgroup_commit_charge+0x56/0x400
[ 8675.435122] ? do_raw_spin_unlock+0x4b/0xc0
[ 8675.436618] ? _raw_spin_unlock+0x1f/0x30
[ 8675.438093] ? __handle_mm_fault+0x499/0x740
[ 8675.439619] ? do_vfs_ioctl+0x56e/0x770
[ 8675.441034] do_vfs_ioctl+0x56e/0x770
[ 8675.442411] ksys_ioctl+0x3a/0x70
[ 8675.443718] ? trace_hardirqs_off_thunk+0x1a/0x1c
[ 8675.445333] __x64_sys_ioctl+0x16/0x20
[ 8675.446705] do_syscall_64+0x50/0x210
[ 8675.448059] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 8675.479187] BTRFS: error (device vdb) in btrfs_create_pending_block_groups:2038: errno=-28 No space left
We now use btrfs_can_overcommit() to see if we can flip a block group
read only. Before this would fail because we weren't taking into
account the usable un-allocated space for allocating chunks. With my
patches we were allowed to do the balance, which is technically correct.
The test is trying to start balance on degraded mount. So now we're
trying to allocate a chunk and cannot because we want to allocate a
RAID1 chunk, but there's only 1 device that's available for usage. This
results in an ENOSPC.
But we shouldn't even be making it this far, we don't have enough
devices to restripe. The problem is we're using btrfs_num_devices(),
that also includes missing devices. That's not actually what we want, we
need to use rw_devices.
The chunk_mutex is not needed here, rw_devices changes only in device
add, remove or replace, all are excluded by EXCL_OP mechanism.
Fixes: e4d8ec0f65b9 ("Btrfs: implement online profile changing")
CC: [email protected] # 4.4+
Signed-off-by: Josef Bacik <[email protected]>
Reviewed-by: David Sterba <[email protected]>
[ add stacktrace, update changelog, drop chunk_mutex ]
Signed-off-by: David Sterba <[email protected]>
|
|
If scrub returns an error we are not copying back the scrub arguments
structure to user space. This prevents user space to know how much
progress scrub has done if an error happened - this includes -ECANCELED
which is returned when users ask for scrub to stop. A particular use
case, which is used in btrfs-progs, is to resume scrub after it is
canceled, in that case it relies on checking the progress from the scrub
arguments structure and then use that progress in a call to resume
scrub.
So fix this by always copying the scrub arguments structure to user
space, overwriting the value returned to user space with -EFAULT only if
copying the structure failed to let user space know that either that
copying did not happen, and therefore the structure is stale, or it
happened partially and the structure is probably not valid and corrupt
due to the partial copy.
Reported-by: Graham Cobb <[email protected]>
Link: https://lore.kernel.org/linux-btrfs/[email protected]/
Fixes: 06fe39ab15a6a4 ("Btrfs: do not overwrite scrub error with fault error in scrub ioctl")
CC: [email protected] # 5.1+
Reviewed-by: Johannes Thumshirn <[email protected]>
Reviewed-by: Qu Wenruo <[email protected]>
Tested-by: Graham Cobb <[email protected]>
Signed-off-by: Filipe Manana <[email protected]>
Reviewed-by: David Sterba <[email protected]>
Signed-off-by: David Sterba <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"This reverts the GPIOLIB_IRQCHIP in the ThunderX driver.
ThunderX is a piece of Arm-based server chip. I converted the driver
to hierarchical gpiochip without access to real silicon and failed
miserably since I didn't take MSI's into account.
Kevin Hao helpfully stepped in and fixed it properly, let's revert it
for v5.5 and put the proper conversion into v5.6"
* tag 'gpio-v5.5-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
Revert "gpio: thunderx: Switch to GPIOLIB_IRQCHIP"
|
|
Pull block fixes from Jens Axboe:
"Three fixes that should go into this release:
- The 32-bit segment size fix that I mentioned last week (Ming)
- Use uint for the block size (Mikulas)
- A null_blk zone write handling fix (Damien)"
* tag 'block-5.5-2020-01-16' of git://git.kernel.dk/linux-block:
block: fix an integer overflow in logical block size
null_blk: Fix zone write handling
block: fix get_max_segment_size() overflow on 32bit arch
|
|
We would not be transmitting using the correct SYSTEMPORT transmit queue
during ndo_select_queue() which looks up the internal TX ring map
because while establishing the mapping we would be off by 4, so for
instance, when we populate switch port mappings we would be doing:
switch port 0, queue 0 -> ring index #0
switch port 0, queue 1 -> ring index #1
...
switch port 0, queue 3 -> ring index #3
switch port 1, queue 0 -> ring index #8 (4 + 4 * 1)
...
instead of using ring index #4. This would cause our ndo_select_queue()
to use the fallback queue mechanism which would pick up an incorrect
ring for that switch port. Fix this by using the correct switch queue
number instead of SYSTEMPORT queue number.
Fixes: 25c440704661 ("net: systemport: Simplify queue mapping logic")
Signed-off-by: Florian Fainelli <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
With the implementation of the system reset controller we lost a setting
that is currently applied by the bootloader and which configures the IMP
port for 2Gb/sec, the default is 1Gb/sec. This is needed given the
number of ports and applications we expect to run so bring back that
setting.
Fixes: 01b0ac07589e ("net: dsa: bcm_sf2: Add support for optional reset controller line")
Signed-off-by: Florian Fainelli <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The sja1105_parse_ports_node function was tested only on device trees
where all ports were enabled. Fix this check so that the driver
continues to probe only with the ports where status is not "disabled",
as expected.
Fixes: 8aa9ebccae87 ("net: dsa: Introduce driver for NXP SJA1105 5-port L2 switch")
Signed-off-by: Vladimir Oltean <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
According to the Datasheet this bit should be 0 (Normal operation) in
default. With the FORCE_LINK_GOOD bit set, it is not possible to get a
link. This patch sets FORCE_LINK_GOOD to the default value after
resetting the phy.
Signed-off-by: Michael Grzeschik <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
The PCIe Root Port driver for CPU Complex PCIe Root Ports are not
loaded on SNR.
The device ID for SNR PCIe3 unit is used by both uncore driver and the
PCIe Root Port driver. If uncore driver is loaded, the PCIe Root Port
driver never be probed.
Remove the PCIe3 unit for SNR for now. The support for PCIe3 unit will
be added later separately.
Signed-off-by: Kan Liang <[email protected]>
Signed-off-by: Peter Zijlstra (Intel) <[email protected]>
Signed-off-by: Ingo Molnar <[email protected]>
Link: https://lkml.kernel.org/r/[email protected]
|
|
An Oops during the boot is found on some SNR machines. It turns out
this is because the snr_uncore_imc_freerunning_events[] array was
missing an end-marker.
Fixes: ee49532b38dd ("perf/x86/intel/uncore: Add IMC uncore support for Snow Ridge")
Reported-by: Like Xu <[email protected]>
Signed-off-by: Kan Liang <[email protected]>
Signed-off-by: Peter Zijlstra (Intel) <[email protected]>
Signed-off-by: Ingo Molnar <[email protected]>
Tested-by: Like Xu <[email protected]>
Cc: [email protected]
Link: https://lkml.kernel.org/r/[email protected]
|
|
The IMC uncore support is missed for E3-1585 v5 CPU.
Intel Xeon E3 V5 Family has Sky Lake CPU.
Add the PCI ID of IMC for Intel Xeon E3 V5 Family.
Reported-by: Rosales-fernandez, Carlos <[email protected]>
Signed-off-by: Kan Liang <[email protected]>
Signed-off-by: Peter Zijlstra (Intel) <[email protected]>
Signed-off-by: Ingo Molnar <[email protected]>
Tested-by: Rosales-fernandez, Carlos <[email protected]>
Link: https://lkml.kernel.org/r/[email protected]
|
|
Vince reports a worrying issue:
| so I was tracking down some odd behavior in the perf_fuzzer which turns
| out to be because perf_even_open() sometimes returns 0 (indicating a file
| descriptor of 0) even though as far as I can tell stdin is still open.
... and further the cause:
| error is triggered if aux_sample_size has non-zero value.
|
| seems to be this line in kernel/events/core.c:
|
| if (perf_need_aux_event(event) && !perf_get_aux_event(event, group_leader))
| goto err_locked;
|
| (note, err is never set)
This seems to be a thinko in commit:
ab43762ef010967e ("perf: Allow normal events to output AUX data")
... and we should probably return -EINVAL here, as this should only
happen when the new event is mis-configured or does not have a
compatible aux_event group leader.
Fixes: ab43762ef010967e ("perf: Allow normal events to output AUX data")
Reported-by: Vince Weaver <[email protected]>
Signed-off-by: Mark Rutland <[email protected]>
Signed-off-by: Peter Zijlstra (Intel) <[email protected]>
Signed-off-by: Ingo Molnar <[email protected]>
Acked-by: Alexander Shishkin <[email protected]>
Tested-by: Vince Weaver <[email protected]>
|
|
When there is not enough memory and napi_alloc_skb() return NULL,
the HNS driver will print error message, and than try again, if
the memory is not enough for a while, huge error message and the
retry operation will cause soft lockup.
When napi_alloc_skb() return NULL because of no memory, we can
get a warn_alloc() call trace, so this patch deletes the error
message. We already use polling mode to handle irq, but the
retry operation will render the polling weight inactive, this
patch just return budget when the rx is not completed to avoid
dead loop.
Fixes: 36eedfde1a36 ("net: hns: Optimize hns_nic_common_poll for better performance")
Fixes: b5996f11ea54 ("net: add Hisilicon Network Subsystem basic ethernet support")
Signed-off-by: Yonglong Liu <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
USB-serial drivers must not be unbound from their ports before the
corresponding USB driver is unbound from the parent interface so
suppress the bind and unbind attributes.
Unbinding a serial driver while it's port is open is a sure way to
trigger a crash as any driver state is released on unbind while port
hangup is handled on the parent USB interface level. Drivers for
multiport devices where ports share a resource such as an interrupt
endpoint also generally cannot handle individual ports going away.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable <[email protected]>
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Signed-off-by: Johan Hovold <[email protected]>
|
|
syzbot reported some bogus lockdep warnings, for example bad unlock
balance in sch_direct_xmit(). They are due to a race condition between
slow path and fast path, that is qdisc_xmit_lock_key gets re-registered
in netdev_update_lockdep_key() on slow path, while we could still
acquire the queue->_xmit_lock on fast path in this small window:
CPU A CPU B
__netif_tx_lock();
lockdep_unregister_key(qdisc_xmit_lock_key);
__netif_tx_unlock();
lockdep_register_key(qdisc_xmit_lock_key);
In fact, unlike the addr_list_lock which has to be reordered when
the master/slave device relationship changes, queue->_xmit_lock is
only acquired on fast path and only when NETIF_F_LLTX is not set,
so there is likely no nested locking for it.
Therefore, we can just get rid of re-registration of
qdisc_xmit_lock_key.
Reported-by: [email protected]
Fixes: ab92d68fc22f ("net: core: add generic lockdep keys")
Cc: Taehee Yoo <[email protected]>
Signed-off-by: Cong Wang <[email protected]>
Acked-by: Taehee Yoo <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
It seems better to init ife->metalist earlier in tcf_ife_init()
to avoid the following crash :
kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] PREEMPT SMP KASAN
CPU: 0 PID: 10483 Comm: syz-executor216 Not tainted 5.5.0-rc5-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:_tcf_ife_cleanup net/sched/act_ife.c:412 [inline]
RIP: 0010:tcf_ife_cleanup+0x6e/0x400 net/sched/act_ife.c:431
Code: 48 c1 ea 03 80 3c 02 00 0f 85 94 03 00 00 49 8b bd f8 00 00 00 48 b8 00 00 00 00 00 fc ff df 4c 8d 67 e8 48 89 fa 48 c1 ea 03 <80> 3c 02 00 0f 85 5c 03 00 00 48 bb 00 00 00 00 00 fc ff df 48 8b
RSP: 0018:ffffc90001dc6d00 EFLAGS: 00010246
RAX: dffffc0000000000 RBX: ffffffff864619c0 RCX: ffffffff815bfa09
RDX: 0000000000000000 RSI: 0000000000000004 RDI: 0000000000000000
RBP: ffffc90001dc6d50 R08: 0000000000000004 R09: fffff520003b8d8e
R10: fffff520003b8d8d R11: 0000000000000003 R12: ffffffffffffffe8
R13: ffff8880a79fc000 R14: ffff88809aba0e00 R15: 0000000000000000
FS: 0000000001b51880(0000) GS:ffff8880ae800000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000563f52cce140 CR3: 0000000093541000 CR4: 00000000001406f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
tcf_action_cleanup+0x62/0x1b0 net/sched/act_api.c:119
__tcf_action_put+0xfa/0x130 net/sched/act_api.c:135
__tcf_idr_release net/sched/act_api.c:165 [inline]
__tcf_idr_release+0x59/0xf0 net/sched/act_api.c:145
tcf_idr_release include/net/act_api.h:171 [inline]
tcf_ife_init+0x97c/0x1870 net/sched/act_ife.c:616
tcf_action_init_1+0x6b6/0xa40 net/sched/act_api.c:944
tcf_action_init+0x21a/0x330 net/sched/act_api.c:1000
tcf_action_add+0xf5/0x3b0 net/sched/act_api.c:1410
tc_ctl_action+0x390/0x488 net/sched/act_api.c:1465
rtnetlink_rcv_msg+0x45e/0xaf0 net/core/rtnetlink.c:5424
netlink_rcv_skb+0x177/0x450 net/netlink/af_netlink.c:2477
rtnetlink_rcv+0x1d/0x30 net/core/rtnetlink.c:5442
netlink_unicast_kernel net/netlink/af_netlink.c:1302 [inline]
netlink_unicast+0x58c/0x7d0 net/netlink/af_netlink.c:1328
netlink_sendmsg+0x91c/0xea0 net/netlink/af_netlink.c:1917
sock_sendmsg_nosec net/socket.c:639 [inline]
sock_sendmsg+0xd7/0x130 net/socket.c:659
____sys_sendmsg+0x753/0x880 net/socket.c:2330
___sys_sendmsg+0x100/0x170 net/socket.c:2384
__sys_sendmsg+0x105/0x1d0 net/socket.c:2417
__do_sys_sendmsg net/socket.c:2426 [inline]
__se_sys_sendmsg net/socket.c:2424 [inline]
__x64_sys_sendmsg+0x78/0xb0 net/socket.c:2424
do_syscall_64+0xfa/0x790 arch/x86/entry/common.c:294
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Fixes: 11a94d7fd80f ("net/sched: act_ife: validate the control action inside init()")
Signed-off-by: Eric Dumazet <[email protected]>
Reported-by: syzbot <[email protected]>
Cc: Davide Caratti <[email protected]>
Reviewed-by: Davide Caratti <[email protected]>
Acked-by: Cong Wang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
|
|
Pablo Neira Ayuso says:
====================
Netfilter updates for net
The following patchset contains Netfilter fixes for net:
1) Fix use-after-free in ipset bitmap destroy path, from Cong Wang.
2) Missing init netns in entry cleanup path of arp_tables,
from Florian Westphal.
3) Fix WARN_ON in set destroy path due to missing cleanup on
transaction error.
4) Incorrect netlink sanity check in tunnel, from Florian Westphal.
5) Missing sanity check for erspan version netlink attribute, also
from Florian.
6) Remove WARN in nft_request_module() that can be triggered from
userspace, from Florian Westphal.
7) Memleak in NFTA_HOOK_DEVS netlink parser, from Dan Carpenter.
8) List poison from commit path for flowtables that are added and
deleted in the same batch, from Florian Westphal.
9) Fix NAT ICMP packet corruption, from Eyal Birger.
====================
Signed-off-by: David S. Miller <[email protected]>
|
|
The commit 91d2a812dfb9 ("locking/rwsem: Make handoff writer
optimistically spin on owner") will allow a recently woken up waiting
writer to spin on the owner. Unfortunately, if the owner happens to be
RWSEM_OWNER_UNKNOWN, the code will incorrectly spin on it leading to a
kernel crash. This is fixed by passing the proper non-spinnable bits
to rwsem_spin_on_owner() so that RWSEM_OWNER_UNKNOWN will be treated
as a non-spinnable target.
Fixes: 91d2a812dfb9 ("locking/rwsem: Make handoff writer optimistically spin on owner")
Reported-by: Christoph Hellwig <[email protected]>
Signed-off-by: Waiman Long <[email protected]>
Signed-off-by: Peter Zijlstra (Intel) <[email protected]>
Tested-by: Christoph Hellwig <[email protected]>
Cc: [email protected]
Link: https://lkml.kernel.org/r/[email protected]
|
|
If the credentials or the mm doesn't match, don't allow the task to
submit anything on behalf of this ring. The task that owns the ring can
pass the file descriptor to another task, but we don't want to allow
that task to submit an SQE that then assumes the ring mm and creds if
it needs to go async.
Cc: [email protected]
Suggested-by: Stefan Metzmacher <[email protected]>
Signed-off-by: Jens Axboe <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"I've been sitting on these longer than I meant, so the patch count is
a bit higher than ideal for this part of the release. There's also
some reverts of double-applied patches that brings the diffstat up a
bit.
With that said, the biggest changes are:
- Revert of duplicate i2c device addition on two Aspeed (BMC)
Devicetrees.
- Move of two device nodes that got applied to the wrong part of the
tree on ASpeed G6.
- Regulator fix for Beaglebone X15 (adding 12/5V supplies)
- Use interrupts for keys on Amlogic SM1 to avoid missed polls
In addition to that, there is a collection of smaller DT fixes:
- Power supply assignment fixes for i.MX6
- Fix of interrupt line for magnetometer on i.MX8 Librem5 devkit
- Build fixlets (selects) for davinci/omap2+
- More interrupt number fixes for Stratix10, Amlogic SM1, etc.
- ... and more similar fixes across different platforms
And some non-DT stuff:
- optee fix to register multiple shared pages properly
- Clock calculation fixes for MMP3
- Clock fixes for OMAP as well"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (42 commits)
MAINTAINERS: Add myself as the co-maintainer for Actions Semi platforms
ARM: dts: imx7: Fix Toradex Colibri iMX7S 256MB NAND flash support
ARM: dts: imx6sll-evk: Remove incorrect power supply assignment
ARM: dts: imx6sl-evk: Remove incorrect power supply assignment
ARM: dts: imx6sx-sdb: Remove incorrect power supply assignment
ARM: dts: imx6qdl-sabresd: Remove incorrect power supply assignment
ARM: dts: imx6q-icore-mipi: Use 1.5 version of i.Core MX6DL
ARM: omap2plus: select RESET_CONTROLLER
ARM: davinci: select CONFIG_RESET_CONTROLLER
ARM: dts: aspeed: rainier: Fix fan fault and presence
ARM: dts: aspeed: rainier: Remove duplicate i2c busses
ARM: dts: aspeed: tacoma: Remove duplicate flash nodes
ARM: dts: aspeed: tacoma: Remove duplicate i2c busses
ARM: dts: aspeed: tacoma: Fix fsi master node
ARM: dts: aspeed-g6: Fix FSI master location
ARM: dts: mmp3: Fix the TWSI ranges
clk: mmp2: Fix the order of timer mux parents
ARM: mmp: do not divide the clock rate
arm64: dts: rockchip: Fix IR on Beelink A1
optee: Fix multi page dynamic shm pool alloc
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"Second collection of clk fixes for the next release.
This one includes a fix for PM on TI SoCs with sysc devices and fixes
a bunch of clks that are stuck always enabled on Qualcomm SDM845 SoCs.
Allwinner SoCs get the usual set of fixes too, mostly correcting
drivers to have the right bits that match the hardware.
There's also a Samsung and Tegra fix in here to mark a clk critical
and avoid a double free.
And finally there's a fix for critical clks that silences a big
warning splat about trying to enable a clk that couldn't even be
prepared"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: ti: dra7-atl: Remove pm_runtime_irq_safe()
clk: qcom: gcc-sdm845: Add missing flag to votable GDSCs
clk: sunxi-ng: h6-r: Fix AR100/R_APB2 parent order
clk: sunxi-ng: h6-r: Simplify R_APB1 clock definition
clk: sunxi-ng: sun8i-r: Fix divider on APB0 clock
clk: Don't try to enable critical clocks if prepare failed
clk: tegra: Fix double-free in tegra_clk_init()
clk: samsung: exynos5420: Keep top G3D clocks enabled
clk: sunxi-ng: r40: Allow setting parent rate for external clock outputs
clk: sunxi-ng: v3s: Fix incorrect number of hw_clks.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fix from Rafael Wysocki:
"Fix a coding mistake in the teo cpuidle governor causing data to be
written beyond the last array element (Ikjoon Jang)"
* tag 'pm-5.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpuidle: teo: Fix intervals[] array indexing bug
|
|
Since I've been doing the maintainership work for couple of cycles, we've
decided to add myself as the co-maintainer along with Andreas.
Link: https://lore.kernel.org/r/[email protected]
Cc: "Andreas Färber" <[email protected]>
Signed-off-by: Manivannan Sadhasivam <[email protected]>
Acked-by: Andreas Färber <[email protected]>
Signed-off-by: Olof Johansson <[email protected]>
|
|
Some work has been done :)
Signed-off-by: Jérôme Pouiller <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Usage of the "buf_loc" variable does not simplify the function.
Signed-off-by: Jérôme Pouiller <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
wfx_tx_queue_get_num_queued() can take advantage of BIT() instead of
maintaining one variable for a counter and another for a mask.
In add, wfx_tx_queue_get_num_queued() has no real reason to return a
size_t instead of an int.
Signed-off-by: Jérôme Pouiller <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Since enum action has now only two cases, it can be dropped. Then
hif_handle_tx_data() can be simplified.
Signed-off-by: Jérôme Pouiller <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
Obviously, the value of wvif->state as no reason to be wrong. At least,
if it the case, dropping the frame is probably not the bast thing to do.
Signed-off-by: Jérôme Pouiller <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
The identifier do_probe is unused since "staging: wfx: remove workaround
to send probe requests"
Signed-off-by: Jérôme Pouiller <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
In current code, packet_id is derivated from mac802.11 packet sequence
number, but this number is only unique for a station. It is not
sufficient.
Signed-off-by: Jérôme Pouiller <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|
|
wfx_ps_notify_sta() is too complex compared to the task it do.
Signed-off-by: Jérôme Pouiller <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>
|