| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Merge the pmdomain fixes for v6.8-rc[n] into the next branch, to allow them
to get tested together with the new changes that are targeted for v6.9.
Signed-off-by: Ulf Hansson <[email protected]>
|
|
Commit 'e3e56c050ab6 ("soc: qcom: rpmhpd: Make power_on actually enable
the domain")' aimed to make sure that a power-domain that is being
enabled without any particular performance-state requested will at least
turn the rail on, to avoid filling DeviceTree with otherwise unnecessary
required-opps properties.
But in the event that aggregation happens on a disabled power-domain, with
an enabled peer without performance-state, both the local and peer
corner are 0. The peer's enabled_corner is not considered, with the
result that the underlying (shared) resource is disabled.
One case where this can be observed is when the display stack keeps mmcx
enabled (but without a particular performance-state vote) in order to
access registers and sync_state happens in the rpmhpd driver. As mmcx_ao
is flushed the state of the peer (mmcx) is not considered and mmcx_ao
ends up turning off "mmcx.lvl" underneath mmcx. This has been observed
several times, but has been painted over in DeviceTree by adding an
explicit vote for the lowest non-disabled performance-state.
Fixes: e3e56c050ab6 ("soc: qcom: rpmhpd: Make power_on actually enable the domain")
Reported-by: Johan Hovold <[email protected]>
Closes: https://lore.kernel.org/linux-arm-msm/[email protected]/
Cc: <[email protected]>
Signed-off-by: Bjorn Andersson <[email protected]>
Reviewed-by: Konrad Dybcio <[email protected]>
Reviewed-by: Dmitry Baryshkov <[email protected]>
Tested-by: Dmitry Baryshkov <[email protected]>
Reviewed-by: Abhinav Kumar <[email protected]>
Reviewed-by: Stephen Boyd <[email protected]>
Tested-by: Johan Hovold <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Ulf Hansson <[email protected]>
|
|
Description in HWM rev0.51E, 9.4 Usage notes, page 455 tells
"It takes several hundreds of microseconds to shutting off and
resuming power domain. Because actual time required for
shutting off and resuming depends on the status of on-board
power line, shutoff/resume time is not guaranteed by
electrical specification"
Let's assume the safe value of waiting is about 1000us.
Signed-off-by: Dien Pham <[email protected]>
Signed-off-by: Takeshi Kihara <[email protected]>
Signed-off-by: Tho Vu <[email protected]>
Signed-off-by: Kuninori Morimoto <[email protected]>
Reviewed-by: Geert Uytterhoeven <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Ulf Hansson <[email protected]>
|
|
Add the power domains CX & GFX found on MSM8974 devices that use PMA8084
instead of the standard PM8841+PM8941 combo.
Signed-off-by: Luca Weiss <[email protected]>
Reviewed-by: Konrad Dybcio <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Ulf Hansson <[email protected]>
|
|
Add the power domains CX & GFX found on devices with MSM8974 and PM8841.
Signed-off-by: Luca Weiss <[email protected]>
Reviewed-by: Konrad Dybcio <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Ulf Hansson <[email protected]>
|
|
Pointer to of_phandle_args is not modified by of_genpd_add_device() and
of_genpd_add_subdomain(), so it can be made pointer to const for code
safety and readability.
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Ulf Hansson <[email protected]>
|
|
The xlate callbacks are supposed to translate of_phandle_args to proper
provider without modifying the of_phandle_args. Make the argument
pointer to const for code safety and readability.
Signed-off-by: Krzysztof Kozlowski <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Ulf Hansson <[email protected]>
|
|
Let's avoid some of the boilerplate code to manage the vcodec PM domains,
by converting into using dev_pm_domain_attach|detach_list().
Cc: Mauro Carvalho Chehab <[email protected]>
Cc: Stanimir Varbanov <[email protected]>
Cc: Vikash Garodia <[email protected]>
Cc: Bjorn Andersson <[email protected]>
Cc: Konrad Dybcio <[email protected]>
Cc: <[email protected]>
Tested-by: Bryan O'Donoghue <[email protected]>
Reviewed-by: Bryan O'Donoghue <[email protected]>
Signed-off-by: Ulf Hansson <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Let's avoid some of the boilerplate code to manage the various PM domain
cases, by converting into using dev_pm_domain_attach|detach_list().
As a part of the conversion, we are moving over to use device_links, which
simplifies the runtime PM support too. Moreover, while attaching let's
trust that an already attached single PM domain is the correct one.
Cc: Mathieu Poirier <[email protected]>
Cc: Bjorn Andersson <[email protected]>
Cc: Konrad Dybcio <[email protected]>
Cc: <[email protected]>
Signed-off-by: Ulf Hansson <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Let's avoid the boilerplate code to manage the multiple PM domain case, by
converting into using dev_pm_domain_attach|detach_list().
Cc: Bjorn Andersson <[email protected]>
Cc: Shawn Guo <[email protected]>
Cc: Sascha Hauer <[email protected]>
Cc: Daniel Baluta <[email protected]>
Cc: <[email protected]>
Tested-by: Iuliana Prodan <[email protected]>
Reviewed-by: Iuliana Prodan <[email protected]>
Reviewed-by: Mathieu Poirier <[email protected]>
Signed-off-by: Ulf Hansson <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Let's avoid the boilerplate code to manage the multiple PM domain case, by
converting into using dev_pm_domain_attach|detach_list().
Cc: Bjorn Andersson <[email protected]>
Cc: Shawn Guo <[email protected]>
Cc: Sascha Hauer <[email protected]>
Cc: Daniel Baluta <[email protected]>
Cc: <[email protected]>
Tested-by: Iuliana Prodan <[email protected]>
Reviewed-by: Iuliana Prodan <[email protected]>
Reviewed-by: Mathieu Poirier <[email protected]>
Signed-off-by: Ulf Hansson <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
Attaching/detaching of a device to multiple PM domains has started to
become a common operation for many drivers, typically during ->probe() and
->remove(). In most cases, this has lead to lots of boilerplate code in the
drivers.
To fixup up the situation, let's introduce a pair of helper functions,
dev_pm_domain_attach|detach_list(), that driver can use instead of the
open-coding. Note that, it seems reasonable to limit the support for these
helpers to DT based platforms, at it's the only valid use case for now.
Suggested-by: Daniel Baluta <[email protected]>
Tested-by: Bryan O'Donoghue <[email protected]>
Tested-by: Iuliana Prodan <[email protected]>
Signed-off-by: Ulf Hansson <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
|
|
According to i.MX8MP RM and HDMI ADD, the fdcc clock is part of
hdmi rx verification IP that should not enable for HDMI TX.
But actually if the clock is disabled before HDMI/LCDIF probe,
LCDIF will not get pixel clock from HDMI PHY and print the error
logs:
[CRTC:39:crtc-2] vblank wait timed out
WARNING: CPU: 2 PID: 9 at drivers/gpu/drm/drm_atomic_helper.c:1634 drm_atomic_helper_wait_for_vblanks.part.0+0x23c/0x260
Add fdcc clock to LCDIF and HDMI TX power domains to fix the issue.
Signed-off-by: Adam Ford <[email protected]>
Reviewed-by: Jacky Bai <[email protected]>
Signed-off-by: Sandor Yu <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Ulf Hansson <[email protected]>
|
|
A wrapper function is available since the commit 7945f929f1a77a1c8887a97ca07f87626858ff42
("drivers: provide devm_platform_ioremap_resource()").
* Thus reuse existing functionality instead of keeping duplicate source code.
* Delete a local variable which became unnecessary with this refactoring.
This issue was transformed by using the Coccinelle software.
Signed-off-by: Markus Elfring <[email protected]>
Reviewed-by: Geert Uytterhoeven <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Ulf Hansson <[email protected]>
|
|
Add support for R-Car V4M (R8A779H0) SoC power areas to the R-Car SYSC
driver.
Signed-off-by: Duy Nguyen <[email protected]>
Signed-off-by: Geert Uytterhoeven <[email protected]>
Acked-by: Niklas Söderlund <[email protected]>
Link: https://lore.kernel.org/r/eed6faa02c628d32676ab8ea0eee636b4ffd6c47.1706194617.git.geert+renesas@glider.be
Signed-off-by: Ulf Hansson <[email protected]>
|
|
This driver assumes that domain->power_dev is non-NULL in its
suspend/resume path. The assumption is valid, since all the devices that
are being looked up here should be described in DT. In case they are not
described in DT, because the DT is faulty, suspend/resume attempt would
trigger NULL pointer dereference.
To avoid this failure, check whether the power_dev assignment is not NULL
right away in probe callback and fail early if it is.
Signed-off-by: Marek Vasut <[email protected]>
Reviewed-by: Peng Fan <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Ulf Hansson <[email protected]>
|
|
devm_kasprintf() returns a pointer to dynamically allocated memory
which can be NULL upon failure. Ensure the allocation was successful
by checking the pointer validity.
Signed-off-by: Kunwu Chan <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Ulf Hansson <[email protected]>
|
|
The R-Car V3U System Controller (SYSC) driver no longer needs these
includes since the factoring out of the common R-Car Gen4 SYSC driver in
commit e62906d6315f652b ("soc: renesas: rcar-gen4-sysc: Introduce R-Car
Gen4 SYSC driver").
The R-Car S4-8 and V4H SYSC drivers never needed these includes, as
these drivers always used the common R-Car Gen4 SYSC driver.
Signed-off-by: Geert Uytterhoeven <[email protected]>
Link: https://lore.kernel.org/r/5b440f84ab8b52499ab307c84154dcbc0f41d1d7.1705931035.git.geert+renesas@glider.be
Signed-off-by: Ulf Hansson <[email protected]>
|
|
In a similar spirit to commit 12ca59b91d04 ("clk: Print an info line
before disabling unused clocks"), print the message in both ignore AND
cleanup cases to better inform the user (and more importantly, the
developer) when it happens.
Signed-off-by: Konrad Dybcio <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Ulf Hansson <[email protected]>
|
|
For no apparent reason (as there's just one RPM per SoC), all RPMPDs
currently store a copy of a pointer to smd_rpm. Introduce a single,
global one to save up on space in each definition.
bloat-o-meter reports:
Total: Before=92010, After=91062, chg -1.03%
Signed-off-by: Konrad Dybcio <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Ulf Hansson <[email protected]>
|
|
Power domains might have parent domains assigned that are automatically
managed by the PM domain core. In particular, parent domains are
automatically powered on/off and setting performance states on child
domains are propagated to parent domains (e.g. using an OPP table from the
device tree).
Currently the parent performance state is always adjusted before the
performance state of the child domain, which is a problem for some cases
when scaling down the performance state. More exactly, it may lead to that
the parent domain could run in a lower performance state, than what is
required by the child domain.
To fix the behaviour, let's differentiate between scaling up/down and
adjust the order of operations:
- When scaling up, parent domains should be adjusted before the child
domain. In case of an error, the rollback happens in reverse order.
- When scaling down, parent domains should be adjusted after the child
domain, in reverse order, just as if we would rollback scaling up.
In case of an error, the rollback happens in normal order (just as
if we would normally scale up).
Signed-off-by: Stephan Gerhold <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Tested-by: Ulf Hansson <[email protected]>
Signed-off-by: Ulf Hansson <[email protected]>
|
|
Merge the pmdomain fixes for v6.8-rc[n] into the next branch, to allow them
to get tested together with the changes that are targeted for v6.9.
Signed-off-by: Ulf Hansson <[email protected]>
|
|
Merge the immutable branch dt into next, to allow the DT bindings to be
tested together with changes that are targeted for v6.9.
Signed-off-by: Ulf Hansson <[email protected]>
|
|
Add the compatibles and indexes for the rpmpd in MSM8974, both with the
standard PM8841+PM8941 PMICs but also devices found with PMA8084.
Signed-off-by: Luca Weiss <[email protected]>
Acked-by: Krzysztof Kozlowski <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Ulf Hansson <[email protected]>
|
|
On unloading of the scmi_perf_domain module got the below splat, when in
the DT provided to the system under test the '#power-domain-cells' property
was missing. Indeed, this particular setup causes the probe to bail out
early without giving any error, which leads to the ->remove() callback gets
to run too, but without all the expected initialized structures in place.
Add a check and bail out early on remove too.
Call trace:
scmi_perf_domain_remove+0x28/0x70 [scmi_perf_domain]
scmi_dev_remove+0x28/0x40 [scmi_core]
device_remove+0x54/0x90
device_release_driver_internal+0x1dc/0x240
driver_detach+0x58/0xa8
bus_remove_driver+0x78/0x108
driver_unregister+0x38/0x70
scmi_driver_unregister+0x28/0x180 [scmi_core]
scmi_perf_domain_driver_exit+0x18/0xb78 [scmi_perf_domain]
__arm64_sys_delete_module+0x1a8/0x2c0
invoke_syscall+0x50/0x128
el0_svc_common.constprop.0+0x48/0xf0
do_el0_svc+0x24/0x38
el0_svc+0x34/0xb8
el0t_64_sync_handler+0x100/0x130
el0t_64_sync+0x190/0x198
Code: a90153f3 f9403c14 f9414800 955f8a05 (b9400a80)
---[ end trace 0000000000000000 ]---
Fixes: 2af23ceb8624 ("pmdomain: arm: Add the SCMI performance domain")
Signed-off-by: Cristian Marussi <[email protected]>
Reviewed-by: Sudeep Holla <[email protected]>
Cc: [email protected]
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Ulf Hansson <[email protected]>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fix from Borislav Petkov:
- Make sure a warning is issued when a hrtimer gets queued after the
timers have been migrated on the CPU down path and thus said timer
will get ignored
* tag 'timers_urgent_for_v6.8_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
hrtimer: Report offline hrtimer enqueue
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
- Correct the minimum CPU family for Transmeta Crusoe in Kconfig so
that such hw can boot again
- Do not take into accout XSTATE buffer size info supplied by userspace
when constructing a sigreturn frame
- Switch get_/put_user* to EX_TYPE_UACCESS exception handling when an
MCE is encountered so that it can be properly recovered from instead
of simply panicking
* tag 'x86_urgent_for_v6.8_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/Kconfig: Transmeta Crusoe is CPU family 5, not 6
x86/fpu: Stop relying on userspace for info to fault in xsave buffer
x86/lib: Revert to _ASM_EXTABLE_UA() for {get,put}_user() fixups
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"21 hotfixes. 12 are cc:stable and the remainder pertain to post-6.7
issues or aren't considered to be needed in earlier kernel versions"
* tag 'mm-hotfixes-stable-2024-02-10-11-16' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (21 commits)
nilfs2: fix potential bug in end_buffer_async_write
mm/damon/sysfs-schemes: fix wrong DAMOS tried regions update timeout setup
nilfs2: fix hang in nilfs_lookup_dirty_data_buffers()
MAINTAINERS: Leo Yan has moved
mm/zswap: don't return LRU_SKIP if we have dropped lru lock
fs,hugetlb: fix NULL pointer dereference in hugetlbs_fill_super
mailmap: switch email address for John Moon
mm: zswap: fix objcg use-after-free in entry destruction
mm/madvise: don't forget to leave lazy MMU mode in madvise_cold_or_pageout_pte_range()
arch/arm/mm: fix major fault accounting when retrying under per-VMA lock
selftests: core: include linux/close_range.h for CLOSE_RANGE_* macros
mm/memory-failure: fix crash in split_huge_page_to_list from soft_offline_page
mm: memcg: optimize parent iteration in memcg_rstat_updated()
nilfs2: fix data corruption in dsync block recovery for small block sizes
mm/userfaultfd: UFFDIO_MOVE implementation should use ptep_get()
exit: wait_task_zombie: kill the no longer necessary spin_lock_irq(siglock)
fs/proc: do_task_stat: use sig->stats_lock to gather the threads/children stats
fs/proc: do_task_stat: move thread_group_cputime_adjusted() outside of lock_task_sighand()
getrusage: use sig->stats_lock rather than lock_task_sighand()
getrusage: move thread_group_cputime_adjusted() outside of lock_task_sighand()
...
|
|
Pull block fixes from Jens Axboe:
- NVMe pull request via Keith:
- Update a potentially stale firmware attribute (Maurizio)
- Fixes for the recent verbose error logging (Keith, Chaitanya)
- Protection information payload size fix for passthrough (Francis)
- Fix for a queue freezing issue in virtblk (Yi)
- blk-iocost underflow fix (Tejun)
- blk-wbt task detection fix (Jan)
* tag 'block-6.8-2024-02-10' of git://git.kernel.dk/linux:
virtio-blk: Ensure no requests in virtqueues before deleting vqs.
blk-iocost: Fix an UBSAN shift-out-of-bounds warning
nvme: use ns->head->pi_size instead of t10_pi_tuple structure size
nvme-core: fix comment to reflect right functions
nvme: move passthrough logging attribute to head
blk-wbt: Fix detection of dirty-throttled tasks
nvme-host: fix the updating of the firmware version
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
Pull firewire fix from Takashi Sakamoto:
"A change to accelerate the device detection step in some cases.
In the self-identification step after bus-reset, all nodes in the same
bus broadcast selfID packet including the value of gap count. The
value is related to the cable hops between nodes, and used to
calculate the subaction gap and the arbitration reset gap.
When each node has the different value of the gap count, the
asynchronous communication between them is unreliable, since an
asynchronous transaction could be interrupted by another asynchronous
transaction before completion. The gap count inconsistency can be
resolved by several ways; e.g. the transfer of PHY configuration
packet and generation of bus-reset.
The current implementation of firewire stack can correctly detect the
gap count inconsistency, however the recovery action from the
inconsistency tends to be delayed after reading configuration ROM of
root node. This results in the long time to probe devices in some
combinations of hardware.
Here the stack is changed to schedule the action as soon as possible"
* tag 'firewire-fixes-6.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: core: send bus reset promptly on gap count error
|
|
Pull smb server fixes from Steve French:
"Two ksmbd server fixes:
- memory leak fix
- a minor kernel-doc fix"
* tag '6.8-rc3-ksmbd-server-fixes' of git://git.samba.org/ksmbd:
ksmbd: free aux buffer if ksmbd_iov_pin_rsp_read fails
ksmbd: Add kernel-doc for ksmbd_extract_sharename() function
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Three small driver fixes and one core fix.
The core fix being a fixup to the one in the last pull request which
didn't entirely move checking of scsi_host_busy() out from under the
host lock"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: core: Remove the ufshcd_release() in ufshcd_err_handling_prepare()
scsi: ufs: core: Fix shift issue in ufshcd_clear_cmd()
scsi: lpfc: Use unsigned type for num_sge
scsi: core: Move scsi_host_busy() out of host lock if it is for per-command
|
|
Pull smb client fixes from Steve French:
- reconnect fix
- multichannel channel selection fix
- minor mount warning fix
- reparse point fix
- null pointer check improvement
* tag '6.8-rc3-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
smb3: clarify mount warning
cifs: handle cases where multiple sessions share connection
cifs: change tcon status when need_reconnect is set on it
smb: client: set correct d_type for reparse points under DFS mounts
smb3: add missing null server pointer check
|
|
Pull ceph fixes from Ilya Dryomov:
"Some fscrypt-related fixups (sparse reads are used only for encrypted
files) and two cap handling fixes from Xiubo and Rishabh"
* tag 'ceph-for-6.8-rc4' of https://github.com/ceph/ceph-client:
ceph: always check dir caps asynchronously
ceph: prevent use-after-free in encode_cap_msg()
ceph: always set initial i_blkbits to CEPH_FSCRYPT_BLOCK_SHIFT
libceph: just wait for more data to be available on the socket
libceph: rename read_sparse_msg_*() to read_partial_sparse_msg_*()
libceph: fail sparse-read if the data length doesn't match
|
|
https://github.com/Paragon-Software-Group/linux-ntfs3
Pull ntfs3 fixes from Konstantin Komarov:
"Fixed:
- size update for compressed file
- some logic errors, overflows
- memory leak
- some code was refactored
Added:
- implement super_operations::shutdown
Improved:
- alternative boot processing
- reduced stack usage"
* tag 'ntfs3_for_6.8' of https://github.com/Paragon-Software-Group/linux-ntfs3: (28 commits)
fs/ntfs3: Slightly simplify ntfs_inode_printk()
fs/ntfs3: Add ioctl operation for directories (FITRIM)
fs/ntfs3: Fix oob in ntfs_listxattr
fs/ntfs3: Fix an NULL dereference bug
fs/ntfs3: Update inode->i_size after success write into compressed file
fs/ntfs3: Fixed overflow check in mi_enum_attr()
fs/ntfs3: Correct function is_rst_area_valid
fs/ntfs3: Use i_size_read and i_size_write
fs/ntfs3: Prevent generic message "attempt to access beyond end of device"
fs/ntfs3: use non-movable memory for ntfs3 MFT buffer cache
fs/ntfs3: Use kvfree to free memory allocated by kvmalloc
fs/ntfs3: Disable ATTR_LIST_ENTRY size check
fs/ntfs3: Fix c/mtime typo
fs/ntfs3: Add NULL ptr dereference checking at the end of attr_allocate_frame()
fs/ntfs3: Add and fix comments
fs/ntfs3: ntfs3_forced_shutdown use int instead of bool
fs/ntfs3: Implement super_operations::shutdown
fs/ntfs3: Drop suid and sgid bits as a part of fpunch
fs/ntfs3: Add file_modified
fs/ntfs3: Correct use bh_read
...
|
|
We've had issues with gcc and 'asm goto' before, and we created a
'asm_volatile_goto()' macro for that in the past: see commits
3f0116c3238a ("compiler/gcc4: Add quirk for 'asm goto' miscompilation
bug") and a9f180345f53 ("compiler/gcc4: Make quirk for
asm_volatile_goto() unconditional").
Then, much later, we ended up removing the workaround in commit
43c249ea0b1e ("compiler-gcc.h: remove ancient workaround for gcc PR
58670") because we no longer supported building the kernel with the
affected gcc versions, but we left the macro uses around.
Now, Sean Christopherson reports a new version of a very similar
problem, which is fixed by re-applying that ancient workaround. But the
problem in question is limited to only the 'asm goto with outputs'
cases, so instead of re-introducing the old workaround as-is, let's
rename and limit the workaround to just that much less common case.
It looks like there are at least two separate issues that all hit in
this area:
(a) some versions of gcc don't mark the asm goto as 'volatile' when it
has outputs:
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=98619
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=110420
which is easy to work around by just adding the 'volatile' by hand.
(b) Internal compiler errors:
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=110422
which are worked around by adding the extra empty 'asm' as a
barrier, as in the original workaround.
but the problem Sean sees may be a third thing since it involves bad
code generation (not an ICE) even with the manually added 'volatile'.
but the same old workaround works for this case, even if this feels a
bit like voodoo programming and may only be hiding the issue.
Reported-and-tested-by: Sean Christopherson <[email protected]>
Link: https://lore.kernel.org/all/[email protected]/
Cc: Nick Desaulniers <[email protected]>
Cc: Uros Bizjak <[email protected]>
Cc: Jakub Jelinek <[email protected]>
Cc: Andrew Pinski <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
|
|
When a user tries to use the "sec=krb5p" mount parameter to encrypt
data on connection to a server (when authenticating with Kerberos), we
indicate that it is not supported, but do not note the equivalent
recommended mount parameter ("sec=krb5,seal") which turns on encryption
for that mount (and uses Kerberos for auth). Update the warning message.
Reviewed-by: Shyam Prasad N <[email protected]>
Signed-off-by: Steve French <[email protected]>
|
|
Based on our implementation of multichannel, it is entirely
possible that a server struct may not be found in any channel
of an SMB session.
In such cases, we should be prepared to move on and search for
the server struct in the next session.
Signed-off-by: Shyam Prasad N <[email protected]>
Signed-off-by: Steve French <[email protected]>
|
|
When a tcon is marked for need_reconnect, the intention
is to have it reconnected.
This change adjusts tcon->status in cifs_tree_connect
when need_reconnect is set. Also, this change has a minor
correction in resetting need_reconnect on success. It makes
sure that it is done with tc_lock held.
Signed-off-by: Shyam Prasad N <[email protected]>
Signed-off-by: Steve French <[email protected]>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
- fix missing TLB flush during early boot on SPARSEMEM_VMEMMAP
configurations
- fixes to correctly implement the break-before-make behavior requried
by the ISA for NAPOT mappings
- fix a missing TLB flush on intermediate mapping changes
- fix build warning about a missing declaration of overflow_stack
- fix performace regression related to incorrect tracking of completed
batch TLB flushes
* tag 'riscv-for-linus-6.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: Fix arch_tlbbatch_flush() by clearing the batch cpumask
riscv: declare overflow_stack as exported from traps.c
riscv: Fix arch_hugetlb_migration_supported() for NAPOT
riscv: Flush the tlb when a page directory is freed
riscv: Fix hugetlb_mask_last_page() when NAPOT is enabled
riscv: Fix set_huge_pte_at() for NAPOT mapping
riscv: mm: execute local TLB flush after populating vmemmap
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing fixes from Steven Rostedt:
- Fix broken direct trampolines being called when another callback is
attached the same function.
ARM 64 does not support FTRACE_WITH_REGS, and when it added direct
trampoline calls from ftrace, it removed the "WITH_REGS" flag from
the ftrace_ops for direct trampolines. This broke x86 as x86 requires
direct trampolines to have WITH_REGS.
This wasn't noticed because direct trampolines work as long as the
function it is attached to is not shared with other callbacks (like
the function tracer). When there are other callbacks, a helper
trampoline is called, to call all the non direct callbacks and when
it returns, the direct trampoline is called.
For x86, the direct trampoline sets a flag in the regs field to tell
the x86 specific code to call the direct trampoline. But this only
works if the ftrace_ops had WITH_REGS set. ARM does things
differently that does not require this. For now, set WITH_REGS if the
arch supports WITH_REGS (which ARM does not), and this makes it work
for both ARM64 and x86.
- Fix wasted memory in the saved_cmdlines logic.
The saved_cmdlines is a cache that maps PIDs to COMMs that tracing
can use. Most trace events only save the PID in the event. The
saved_cmdlines file lists PIDs to COMMs so that the tracing tools can
show an actual name and not just a PID for each event. There's an
array of PIDs that map to a small set of saved COMM strings. The
array is set to PID_MAX_DEFAULT which is usually set to 32768. When a
PID comes in, it will add itself to this array along with the index
into the COMM array (note if the system allows more than
PID_MAX_DEFAULT, this cache is similar to cache lines as an update of
a PID that has the same PID_MAX_DEFAULT bits set will flush out
another task with the same matching bits set).
A while ago, the size of this cache was changed to be dynamic and the
array was moved into a structure and created with kmalloc(). But this
new structure had the size of 131104 bytes, or 0x20020 in hex. As
kmalloc allocates in powers of two, it was actually allocating
0x40000 bytes (262144) leaving 131040 bytes of wasted memory. The
last element of this structure was a pointer to the COMM string array
which defaulted to just saving 128 COMMs.
By changing the last field of this structure to a variable length
string, and just having it round up to fill the allocated memory, the
default size of the saved COMM cache is now 8190. This not only uses
the wasted space, but actually saves space by removing the extra
allocation for the COMM names.
* tag 'trace-v6.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing: Fix wasted memory in saved_cmdlines logic
ftrace: Fix DIRECT_CALLS to use SAVE_REGS by default
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull probes fixes from Masami Hiramatsu:
- remove unnecessary initial values of kprobes local variables
- probe-events parser bug fixes:
- calculate the argument size and format string after setting type
information from BTF, because BTF can change the size and format
string.
- show $comm parse error correctly instead of failing silently.
* tag 'probes-fixes-v6.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
kprobes: Remove unnecessary initial values of variables
tracing/probes: Fix to set arg size and fmt after setting type from BTF
tracing/probes: Fix to show a parse error for bad type for $comm
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi
Pull EFI fixes from Ard Biesheuvel:
"The only notable change here is the patch that changes the way we deal
with spurious errors from the EFI memory attribute protocol. This will
be backported to v6.6, and is intended to ensure that we will not
paint ourselves into a corner when we tighten this further in order to
comply with MS requirements on signed EFI code.
Note that this protocol does not currently exist in x86 production
systems in the field, only in Microsoft's fork of OVMF, but it will be
mandatory for Windows logo certification for x86 PCs in the future.
- Tighten ELF relocation checks on the RISC-V EFI stub
- Give up if the new EFI memory attributes protocol fails spuriously
on x86
- Take care not to place the kernel in the lowest 16 MB of DRAM on
x86
- Omit special purpose EFI memory from memblock
- Some fixes for the CXL CPER reporting code
- Make the PE/COFF layout of mixed-mode capable images comply with a
strict interpretation of the spec"
* tag 'efi-fixes-for-v6.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi:
x86/efistub: Use 1:1 file:memory mapping for PE/COFF .compat section
cxl/trace: Remove unnecessary memcpy's
cxl/cper: Fix errant CPER prints for CXL events
efi: Don't add memblocks for soft-reserved memory
efi: runtime: Fix potential overflow of soft-reserved region size
efi/libstub: Add one kernel-doc comment
x86/efistub: Avoid placing the kernel below LOAD_PHYSICAL_ADDR
x86/efistub: Give up if memory attribute protocol returns an error
riscv/efistub: Tighten ELF relocation check
riscv/efistub: Ensure GP-relative addressing is not used
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci fixes from Bjorn Helgaas:
- Fix an unintentional truncation of DWC MSI-X address to 32 bits and
update similar MSI code to match (Dan Carpenter)
* tag 'pci-v6.8-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
PCI: dwc: Clean up dw_pcie_ep_raise_msi_irq() alignment
PCI: dwc: Fix a 64bit bug in dw_pcie_ep_raise_msix_irq()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
- coretemp: Various fixes, and increase number of supported CPU cores
- aspeed-pwm-tacho: Add missing mutex protection
* tag 'hwmon-for-v6.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (coretemp) Enlarge per package core count limit
hwmon: (coretemp) Fix bogus core_id to attr name mapping
hwmon: (coretemp) Fix out-of-bounds memory access
hwmon: (aspeed-pwm-tacho) mutex for tach reading
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"MMC core:
- Allow non-sleeping read-only slot-gpio
MMC host:
- sdhci-pci-o2micro: Fix a warm reboot BIOS issue"
* tag 'mmc-v6.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: slot-gpio: Allow non-sleeping GPIO ro
mmc: sdhci-pci-o2micro: Fix a warm reboot issue that disk can't be detected by BIOS
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm
Pull pmdomain fixes from Ulf Hansson:
"Core:
- Move the unused cleanup to a _sync initcall
Providers:
- mediatek: Fix race conditions at probe/remove with genpd
- renesas: r8a77980-sysc: CR7 must be always on"
* tag 'pmdomain-v6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm:
pmdomain: mediatek: fix race conditions with genpd
pmdomain: renesas: r8a77980-sysc: CR7 must be always on
pmdomain: core: Move the unused cleanup to a _sync initcall
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fix from Bartosz Golaszewski:
- remove the new GPIO device from the global list unconditionally in
error path in core GPIOLIB
* tag 'gpio-fixes-for-v6.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: remove GPIO device from the list unconditionally in error path
|
|
Pull drm fixes from Dave Airlie:
"Regular weekly fixes, xe, amdgpu and msm are most of them, with some
misc in i915, ivpu and nouveau, scattered but nothing too intense at
this point.
i915:
- gvt: docs fix, uninit var, MAINTAINERS
ivpu:
- add aborted job status
- disable d3 hot delay
- mmu fixes
nouveau:
- fix gsp rpc size request
- fix dma buffer leaks
- use common code for gsp mem ctor
xe:
- Fix a loop in an error path
- Fix a missing dma-fence reference
- Fix a retry path on userptr REMAP
- Workaround for a false gcc warning
- Fix missing map of the usm batch buffer in the migrate vm.
- Fix a memory leak.
- Fix a bad assumption of used page size
- Fix hitting a BUG() due to zero pages to map.
- Remove some leftover async bind queue relics
amdgpu:
- Misc NULL/bounds check fixes
- ODM pipe policy fix
- Aborted suspend fixes
- JPEG 4.0.5 fix
- DCN 3.5 fixes
- PSP fix
- DP MST fix
- Phantom pipe fix
- VRAM vendor fix
- Clang fix
- SR-IOV fix
msm:
- DPU:
- fix for kernel doc warnings and smatch warnings in dpu_encoder
- fix for smatch warning in dpu_encoder
- fix the bus bandwidth value for SDM670
- DP:
- fixes to handle unknown bpc case correctly for DP
- fix for MISC0 programming
- GPU:
- dmabuf vmap fix
- a610 UBWC corruption fix (incorrect hbb)
- revert a commit that was making GPU recovery unreliable"
* tag 'drm-fixes-2024-02-09' of git://anongit.freedesktop.org/drm/drm: (43 commits)
drm/xe: Remove TEST_VM_ASYNC_OPS_ERROR
drm/xe/vm: don't ignore error when in_kthread
drm/xe: Assume large page size if VMA not yet bound
drm/xe/display: Fix memleak in display initialization
drm/xe: Map both mem.kernel_bb_pool and usm.bb_pool
drm/xe: circumvent bogus stringop-overflow warning
drm/xe: Pick correct userptr VMA to repin on REMAP op failure
drm/xe: Take a reference in xe_exec_queue_last_fence_get()
drm/xe: Fix loop in vm_bind_ioctl_ops_unwind
drm/amdgpu: Fix HDP flush for VFs on nbio v7.9
drm/amd/display: Implement bounds check for stream encoder creation in DCN301
drm/amd/display: Increase frame-larger-than for all display_mode_vba files
drm/amd/display: Clear phantom stream count and plane count
drm/amdgpu: Avoid fetching VRAM vendor info
drm/amd/display: Disable ODM by default for DCN35
drm/amd/display: Update phantom pipe enable / disable sequence
drm/amd/display: Fix MST Null Ptr for RV
drm/amdgpu: Fix shared buff copy to user
drm/amd/display: Increase eval/entry delay for DCN35
drm/amdgpu: remove asymmetrical irq disabling in jpeg 4.0.5 suspend
...
|