aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2019-10-27usb: dwc3: remove the call trace of USBx_GFLADJYinbo Zhu1-2/+1
layerscape board sometimes reported some usb call trace, that is due to kernel sent LPM tokerns automatically when it has no pending transfers and think that the link is idle enough to enter L1, which procedure will ask usb register has a recovery,then kernel will compare USBx_GFLADJ and set GFLADJ_30MHZ, GFLADJ_30MHZ_REG until GFLADJ_30MHZ is equal 0x20, if the conditions were met then issue occur, but whatever the conditions whether were met that usb is all need keep GFLADJ_30MHZ of value is 0x20 (xhci spec ask use GFLADJ_30MHZ to adjust any offset from clock source that generates the clock that drives the SOF counter, 0x20 is default value of it)That is normal logic, so need remove the call trace. Signed-off-by: Yinbo Zhu <[email protected]> Signed-off-by: Felipe Balbi <[email protected]>
2019-10-27usb: gadget: configfs: fix concurrent issue between composite APIsPeter Chen1-5/+105
We meet several NULL pointer issues if configfs_composite_unbind and composite_setup (or composite_disconnect) are running together. These issues occur when do the function switch stress test, the configfs_compsoite_unbind is called from user mode by echo "" to /sys/../UDC entry, and meanwhile, the setup interrupt or disconnect interrupt occurs by hardware. The composite_setup will get the cdev from get_gadget_data, but configfs_composite_unbind will set gadget data as NULL, so the NULL pointer issue occurs. This concurrent is hard to reproduce by native kernel, but can be reproduced by android kernel. In this commit, we introduce one spinlock belongs to structure gadget_info since we can't use the same spinlock in usb_composite_dev due to exclusive running together between composite_setup and configfs_composite_unbind. And one bit flag 'unbind' to indicate the code is at unbind routine, this bit is needed due to we release the lock at during configfs_composite_unbind sometimes, and composite_setup may be run at that time. Several oops: oops 1: android_work: sent uevent USB_STATE=CONNECTED configfs-gadget gadget: super-speed config #1: b android_work: sent uevent USB_STATE=CONFIGURED init: Received control message 'start' for 'adbd' from pid: 3515 (system_server) Unable to handle kernel NULL pointer dereference at virtual address 0000002a init: Received control message 'stop' for 'adbd' from pid: 3375 (/vendor/bin/hw/[email protected]) Mem abort info: Exception class = DABT (current EL), IL = 32 bits SET = 0, FnV = 0 EA = 0, S1PTW = 0 Data abort info: ISV = 0, ISS = 0x00000004 CM = 0, WnR = 0 user pgtable: 4k pages, 48-bit VAs, pgd = ffff8008f1b7f000 [000000000000002a] *pgd=0000000000000000 Internal error: Oops: 96000004 [#1] PREEMPT SMP Modules linked in: CPU: 4 PID: 2457 Comm: irq/125-5b11000 Not tainted 4.14.98-07846-g0b40a9b-dirty #16 Hardware name: Freescale i.MX8QM MEK (DT) task: ffff8008f2a98000 task.stack: ffff00000b7b8000 PC is at composite_setup+0x44/0x1508 LR is at android_setup+0xb8/0x13c pc : [<ffff0000089ffb3c>] lr : [<ffff000008a032fc>] pstate: 800001c5 sp : ffff00000b7bbb80 x29: ffff00000b7bbb80 x28: ffff8008f2a3c010 x27: 0000000000000001 x26: 0000000000000000 [1232/1897] audit: audit_lost=25791 audit_rate_limit=5 audit_backlog_limit=64 x25: 00000000ffffffa1 x24: ffff8008f2a3c010 audit: rate limit exceeded x23: 0000000000000409 x22: ffff000009c8e000 x21: ffff8008f7a8b428 x20: ffff00000afae000 x19: ffff0000089ff000 x18: 0000000000000000 x17: 0000000000000000 x16: ffff0000082b7c9c x15: 0000000000000000 x14: f1866f5b952aca46 x13: e35502e30d44349c x12: 0000000000000008 x11: 0000000000000008 x10: 0000000000000a30 x9 : ffff00000b7bbd00 x8 : ffff8008f2a98a90 x7 : ffff8008f27a9c90 x6 : 0000000000000001 x5 : 0000000000000000 x4 : 0000000000000001 x3 : 0000000000000000 x2 : 0000000000000006 x1 : ffff0000089ff8d0 x0 : 732a010310b9ed00 X7: 0xffff8008f27a9c10: 9c10 00000002 00000000 00000001 00000000 13110000 ffff0000 00000002 00208040 9c30 00000000 00000000 00000000 00000000 00000000 00000005 00000029 00000000 9c50 00051778 00000001 f27a8e00 ffff8008 00000005 00000000 00000078 00000078 9c70 00000078 00000000 09031d48 ffff0000 00100000 00000000 00400000 00000000 9c90 00000001 00000000 00000000 00000000 00000000 00000000 ffefb1a0 ffff8008 9cb0 f27a9ca8 ffff8008 00000000 00000000 b9d88037 00000173 1618a3eb 00000001 9cd0 870a792a 0000002e 16188fe6 00000001 0000242b 00000000 00000000 00000000 using random self ethernet address 9cf0 019a4646 00000000 000547f3 00000000 ecfd6c33 00000002 00000000 using random host ethernet address 00000000 X8: 0xffff8008f2a98a10: 8a10 00000000 00000000 f7788d00 ffff8008 00000001 00000000 00000000 00000000 8a30 eb218000 ffff8008 f2a98000 ffff8008 f2a98000 ffff8008 09885000 ffff0000 8a50 f34df480 ffff8008 00000000 00000000 f2a98648 ffff8008 09c8e000 ffff0000 8a70 fff2c800 ffff8008 09031d48 ffff0000 0b7bbd00 ffff0000 0b7bbd00 ffff0000 8a90 080861bc ffff0000 00000000 00000000 00000000 00000000 00000000 00000000 8ab0 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 8ad0 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 8af0 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 X21: 0xffff8008f7a8b3a8: b3a8 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 b3c8 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 b3e8 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 b408 00000000 00000000 00000000 00000000 00000000 00000000 00000001 00000000 b428 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 b448 0053004d 00540046 00300031 00010030 eb07b520 ffff8008 20011201 00000003 b468 e418d109 0104404e 00010302 00000000 eb07b558 ffff8008 eb07b558 ffff8008 b488 f7a8b488 ffff8008 f7a8b488 ffff8008 f7a8b300 ffff8008 00000000 00000000 X24: 0xffff8008f2a3bf90: bf90 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 bfb0 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 bfd0 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 bff0 00000000 00000000 00000000 00000000 f76c8010 ffff8008 f76c8010 ffff8008 c010 00000000 00000000 f2a3c018 ffff8008 f2a3c018 ffff8008 08a067dc ffff0000 c030 f2a5a000 ffff8008 091c3650 ffff0000 f716fd18 ffff8008 f716fe30 ffff8008 c050 f2ce4a30 ffff8008 00000000 00000005 00000000 00000000 095d1568 ffff0000 c070 f76c8010 ffff8008 f2ce4b00 ffff8008 095cac68 ffff0000 f2a5a028 ffff8008 X28: 0xffff8008f2a3bf90: bf90 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 bfb0 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 bfd0 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 bff0 00000000 00000000 00000000 00000000 f76c8010 ffff8008 f76c8010 ffff8008 c010 00000000 00000000 f2a3c018 ffff8008 f2a3c018 ffff8008 08a067dc ffff0000 c030 f2a5a000 ffff8008 091c3650 ffff0000 f716fd18 ffff8008 f716fe30 ffff8008 c050 f2ce4a30 ffff8008 00000000 00000005 00000000 00000000 095d1568 ffff0000 c070 f76c8010 ffff8008 f2ce4b00 ffff8008 095cac68 ffff0000 f2a5a028 ffff8008 Process irq/125-5b11000 (pid: 2457, stack limit = 0xffff00000b7b8000) Call trace: Exception stack(0xffff00000b7bba40 to 0xffff00000b7bbb80) ba40: 732a010310b9ed00 ffff0000089ff8d0 0000000000000006 0000000000000000 ba60: 0000000000000001 0000000000000000 0000000000000001 ffff8008f27a9c90 ba80: ffff8008f2a98a90 ffff00000b7bbd00 0000000000000a30 0000000000000008 baa0: 0000000000000008 e35502e30d44349c f1866f5b952aca46 0000000000000000 bac0: ffff0000082b7c9c 0000000000000000 0000000000000000 ffff0000089ff000 bae0: ffff00000afae000 ffff8008f7a8b428 ffff000009c8e000 0000000000000409 bb00: ffff8008f2a3c010 00000000ffffffa1 0000000000000000 0000000000000001 bb20: ffff8008f2a3c010 ffff00000b7bbb80 ffff000008a032fc ffff00000b7bbb80 bb40: ffff0000089ffb3c 00000000800001c5 ffff00000b7bbb80 732a010310b9ed00 bb60: ffffffffffffffff ffff0000080f777c ffff00000b7bbb80 ffff0000089ffb3c [<ffff0000089ffb3c>] composite_setup+0x44/0x1508 [<ffff000008a032fc>] android_setup+0xb8/0x13c [<ffff0000089bd9a8>] cdns3_ep0_delegate_req+0x44/0x70 [<ffff0000089bdff4>] cdns3_check_ep0_interrupt_proceed+0x33c/0x654 [<ffff0000089bca44>] cdns3_device_thread_irq_handler+0x4b0/0x4bc [<ffff0000089b77b4>] cdns3_thread_irq+0x48/0x68 [<ffff000008145bf0>] irq_thread_fn+0x28/0x88 [<ffff000008145e38>] irq_thread+0x13c/0x228 [<ffff0000080fed70>] kthread+0x104/0x130 [<ffff000008085064>] ret_from_fork+0x10/0x18 oops2: composite_disconnect: Calling disconnect on a Gadget that is not connected android_work: did not send uevent (0 0 (null)) init: Received control message 'stop' for 'adbd' from pid: 3359 (/vendor/bin/hw/[email protected]) init: Sending signal 9 to service 'adbd' (pid 22343) process group... ------------[ cut here ]------------ audit: audit_lost=180038 audit_rate_limit=5 audit_backlog_limit=64 audit: rate limit exceeded WARNING: CPU: 0 PID: 3468 at kernel_imx/drivers/usb/gadget/composite.c:2009 composite_disconnect+0x80/0x88 Modules linked in: CPU: 0 PID: 3468 Comm: HWC-UEvent-Thre Not tainted 4.14.98-07846-g0b40a9b-dirty #16 Hardware name: Freescale i.MX8QM MEK (DT) task: ffff8008f2349c00 task.stack: ffff00000b0a8000 PC is at composite_disconnect+0x80/0x88 LR is at composite_disconnect+0x80/0x88 pc : [<ffff0000089ff9b0>] lr : [<ffff0000089ff9b0>] pstate: 600001c5 sp : ffff000008003dd0 x29: ffff000008003dd0 x28: ffff8008f2349c00 x27: ffff000009885018 x26: ffff000008004000 Timeout for IPC response! x25: ffff000009885018 x24: ffff000009c8e280 x23: ffff8008f2d98010 x22: 00000000000001c0 x21: ffff8008f2d98394 x20: ffff8008f2d98010 x19: 0000000000000000 x18: 0000e3956f4f075a fxos8700 4-001e: i2c block read acc failed x17: 0000e395735727e8 x16: ffff00000829f4d4 x15: ffffffffffffffff x14: 7463656e6e6f6320 x13: 746f6e2009090920 x12: 7369207461687420 x11: 7465676461472061 x10: 206e6f207463656e x9 : 6e6f637369642067 x8 : ffff000009c8e280 x7 : ffff0000086ca6cc x6 : ffff000009f15e78 x5 : 0000000000000000 x4 : 0000000000000000 x3 : ffffffffffffffff x2 : c3f28b86000c3900 x1 : c3f28b86000c3900 x0 : 000000000000004e X20: 0xffff8008f2d97f90: 7f90 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 7fb0 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 libprocessgroup: Failed to kill process cgroup uid 0 pid 22343 in 215ms, 1 processes remain 7fd0 Timeout for IPC response! 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 using random self ethernet address 7ff0 00000000 00000000 00000000 00000000 f76c8010 ffff8008 f76c8010 ffff8008 8010 00000100 00000000 f2d98018 ffff8008 f2d98018 ffff8008 08a067dc using random host ethernet address ffff0000 8030 f206d800 ffff8008 091c3650 ffff0000 f7957b18 ffff8008 f7957730 ffff8008 8050 f716a630 ffff8008 00000000 00000005 00000000 00000000 095d1568 ffff0000 8070 f76c8010 ffff8008 f716a800 ffff8008 095cac68 ffff0000 f206d828 ffff8008 X21: 0xffff8008f2d98314: 8314 ffff8008 00000000 00000000 00000000 00000000 00000000 00000000 00000000 8334 00000000 00000000 00000000 00000000 00000000 08a04cf4 ffff0000 00000000 8354 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 8374 00000000 00000000 00000000 00001001 00000000 00000000 00000000 00000000 8394 e4bbe4bb 0f230000 ffff0000 0afae000 ffff0000 ae001000 00000000 f206d400 Timeout for IPC response! 83b4 ffff8008 00000000 00000000 f7957b18 ffff8008 f7957718 ffff8008 f7957018 83d4 ffff8008 f7957118 ffff8008 f7957618 ffff8008 f7957818 ffff8008 f7957918 83f4 ffff8008 f7957d18 ffff8008 00000000 00000000 00000000 00000000 00000000 X23: 0xffff8008f2d97f90: 7f90 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 7fb0 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 7fd0 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 7ff0 00000000 00000000 00000000 00000000 f76c8010 ffff8008 f76c8010 ffff8008 8010 00000100 00000000 f2d98018 ffff8008 f2d98018 ffff8008 08a067dc ffff0000 8030 f206d800 ffff8008 091c3650 ffff0000 f7957b18 ffff8008 f7957730 ffff8008 8050 f716a630 ffff8008 00000000 00000005 00000000 00000000 095d1568 ffff0000 8070 f76c8010 ffff8008 f716a800 ffff8008 095cac68 ffff0000 f206d828 ffff8008 X28: 0xffff8008f2349b80: 9b80 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 9ba0 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 9bc0 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 9be0 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 9c00 00000022 00000000 ffffffff ffffffff 00010001 00000000 00000000 00000000 9c20 0b0a8000 ffff0000 00000002 00404040 00000000 00000000 00000000 00000000 9c40 00000001 00000000 00000001 00000000 001ebd44 00000001 f390b800 ffff8008 9c60 00000000 00000001 00000070 00000070 00000070 00000000 09031d48 ffff0000 Call trace: Exception stack(0xffff000008003c90 to 0xffff000008003dd0) 3c80: 000000000000004e c3f28b86000c3900 3ca0: c3f28b86000c3900 ffffffffffffffff 0000000000000000 0000000000000000 3cc0: ffff000009f15e78 ffff0000086ca6cc ffff000009c8e280 6e6f637369642067 3ce0: 206e6f207463656e 7465676461472061 7369207461687420 746f6e2009090920 3d00: 7463656e6e6f6320 ffffffffffffffff ffff00000829f4d4 0000e395735727e8 3d20: 0000e3956f4f075a 0000000000000000 ffff8008f2d98010 ffff8008f2d98394 3d40: 00000000000001c0 ffff8008f2d98010 ffff000009c8e280 ffff000009885018 3d60: ffff000008004000 ffff000009885018 ffff8008f2349c00 ffff000008003dd0 3d80: ffff0000089ff9b0 ffff000008003dd0 ffff0000089ff9b0 00000000600001c5 3da0: ffff8008f33f2cd8 0000000000000000 0000ffffffffffff 0000000000000000 init: Received control message 'start' for 'adbd' from pid: 3359 (/vendor/bin/hw/[email protected]) 3dc0: ffff000008003dd0 ffff0000089ff9b0 [<ffff0000089ff9b0>] composite_disconnect+0x80/0x88 [<ffff000008a044d4>] android_disconnect+0x3c/0x68 [<ffff0000089ba9f8>] cdns3_device_irq_handler+0xfc/0x2c8 [<ffff0000089b84c0>] cdns3_irq+0x44/0x94 [<ffff00000814494c>] __handle_irq_event_percpu+0x60/0x24c [<ffff000008144c0c>] handle_irq_event+0x58/0xc0 [<ffff00000814873c>] handle_fasteoi_irq+0x98/0x180 [<ffff000008143a10>] generic_handle_irq+0x24/0x38 [<ffff000008144170>] __handle_domain_irq+0x60/0xac [<ffff0000080819c4>] gic_handle_irq+0xd4/0x17c Signed-off-by: Peter Chen <[email protected]> Signed-off-by: Felipe Balbi <[email protected]>
2019-10-27usb: dwc3: pci: prevent memory leak in dwc3_pci_probeNavid Emamdoost1-1/+1
In dwc3_pci_probe a call to platform_device_alloc allocates a device which is correctly put in case of error except one case: when the call to platform_device_add_properties fails it directly returns instead of going to error handling. This commit replaces return with the goto. Fixes: 1a7b12f69a94 ("usb: dwc3: pci: Supply device properties via driver data") Signed-off-by: Navid Emamdoost <[email protected]> Signed-off-by: Felipe Balbi <[email protected]>
2019-10-27usb: gadget: composite: Fix possible double free memory bugChandana Kishori Chiluveru1-0/+4
composite_dev_cleanup call from the failure of configfs_composite_bind frees up the cdev->os_desc_req and cdev->req. If the previous calls of bind and unbind is successful these will carry stale values. Consider the below sequence of function calls: configfs_composite_bind() composite_dev_prepare() - Allocate cdev->req, cdev->req->buf composite_os_desc_req_prepare() - Allocate cdev->os_desc_req, cdev->os_desc_req->buf configfs_composite_unbind() composite_dev_cleanup() - free the cdev->os_desc_req->buf and cdev->req->buf Next composition switch configfs_composite_bind() - If it fails goto err_comp_cleanup will call the composite_dev_cleanup() function composite_dev_cleanup() - calls kfree up with the stale values of cdev->req->buf and cdev->os_desc_req from the previous configfs_composite_bind call. The free call on these stale values leads to double free. Hence, Fix this issue by setting request and buffer pointer to NULL after kfree. Signed-off-by: Chandana Kishori Chiluveru <[email protected]> Signed-off-by: Felipe Balbi <[email protected]>
2019-10-27usb: gadget: udc: atmel: Fix interrupt storm in FIFO mode.Cristian Birsan1-2/+4
Fix interrupt storm generated by endpoints when working in FIFO mode. The TX_COMPLETE interrupt is used only by control endpoints processing. Do not enable it for other types of endpoints. Fixes: 914a3f3b3754 ("USB: add atmel_usba_udc driver") Signed-off-by: Cristian Birsan <[email protected]> Signed-off-by: Felipe Balbi <[email protected]>
2019-10-27usb: renesas_usbhs: fix type of bufBen Dooks (Codethink)1-1/+1
Fix the type of buf in __usbhsg_recip_send_status to be __le16 to avoid the following sparse warning: drivers/usb/renesas_usbhs/mod_gadget.c:335:14: warning: incorrect type in assignment (different base types) drivers/usb/renesas_usbhs/mod_gadget.c:335:14: expected unsigned short drivers/usb/renesas_usbhs/mod_gadget.c:335:14: got restricted __le16 [usertype] Reviewed-by: Yoshihiro Shimoda <[email protected]> Signed-off-by: Ben Dooks <[email protected]> Signed-off-by: Felipe Balbi <[email protected]>
2019-10-27usb: renesas_usbhs: Fix warnings in usbhsg_recip_handler_std_set_device()Yoshihiro Shimoda1-1/+1
This patch fixes the following sparse warnings by shifting 8-bits after le16_to_cpu(). drivers/usb/renesas_usbhs/mod_gadget.c:268:47: warning: restricted __le16 degrades to integer drivers/usb/renesas_usbhs/mod_gadget.c:268:47: warning: cast to restricted __le16 Signed-off-by: Yoshihiro Shimoda <[email protected]> Signed-off-by: Felipe Balbi <[email protected]>
2019-10-27usb: gadget: udc: renesas_usb3: Fix __le16 warningsYoshihiro Shimoda1-5/+6
This patch fixes the following sparse warnings by using a macro and a suitable variable type. drivers/usb/gadget/udc/renesas_usb3.c:1547:17: warning: restricted __le16 degrades to integer drivers/usb/gadget/udc/renesas_usb3.c:1550:43: warning: incorrect type in argument 2 (different base types) drivers/usb/gadget/udc/renesas_usb3.c:1550:43: expected unsigned short [usertype] addr drivers/usb/gadget/udc/renesas_usb3.c:1550:43: got restricted __le16 [usertype] wValue drivers/usb/gadget/udc/renesas_usb3.c:1607:24: warning: incorrect type in assignment (different base types) drivers/usb/gadget/udc/renesas_usb3.c:1607:24: expected unsigned short [assigned] [usertype] status drivers/usb/gadget/udc/renesas_usb3.c:1607:24: got restricted __le16 [usertype] drivers/usb/gadget/udc/renesas_usb3.c:1775:17: warning: restricted __le16 degrades to integer Signed-off-by: Yoshihiro Shimoda <[email protected]> Signed-off-by: Felipe Balbi <[email protected]>
2019-10-27usb: renesas_usbhs: fix __le16 warningsBen Dooks (Codethink)1-6/+6
Fix the warnings generated by casting to/from __le16 without using the correct functions. Fixes the following sparse warnings: drivers/usb/renesas_usbhs/common.c:165:25: warning: incorrect type in assignment (different base types) drivers/usb/renesas_usbhs/common.c:165:25: expected restricted __le16 [usertype] wValue drivers/usb/renesas_usbhs/common.c:165:25: got unsigned short drivers/usb/renesas_usbhs/common.c:166:25: warning: incorrect type in assignment (different base types) drivers/usb/renesas_usbhs/common.c:166:25: expected restricted __le16 [usertype] wIndex drivers/usb/renesas_usbhs/common.c:166:25: got unsigned short drivers/usb/renesas_usbhs/common.c:167:25: warning: incorrect type in assignment (different base types) drivers/usb/renesas_usbhs/common.c:167:25: expected restricted __le16 [usertype] wLength drivers/usb/renesas_usbhs/common.c:167:25: got unsigned short drivers/usb/renesas_usbhs/common.c:173:39: warning: incorrect type in argument 3 (different base types) drivers/usb/renesas_usbhs/common.c:173:39: expected unsigned short [usertype] data drivers/usb/renesas_usbhs/common.c:173:39: got restricted __le16 [usertype] wValue drivers/usb/renesas_usbhs/common.c:174:39: warning: incorrect type in argument 3 (different base types) drivers/usb/renesas_usbhs/common.c:174:39: expected unsigned short [usertype] data drivers/usb/renesas_usbhs/common.c:174:39: got restricted __le16 [usertype] wIndex drivers/usb/renesas_usbhs/common.c:175:39: warning: incorrect type in argument 3 (different base types) drivers/usb/renesas_usbhs/common.c:175:39: expected unsigned short [usertype] data Note. I belive this to be correct, and should be a no-op on arm. Reviewed-by: Geert Uytterhoeven <[email protected]> Reviewed-by: Yoshihiro Shimoda <[email protected]> Signed-off-by: Ben Dooks <[email protected]> Signed-off-by: Felipe Balbi <[email protected]>
2019-10-27usb: cdns3: include host-export,h for cdns3_host_initBen Dooks (Codethink)2-1/+1
The cdns3_host_init() function is declared in host-export.h but host.c does not include it. Add the include to have the declaration present (and remove the declaration of cdns3_host_exit which is now static). Fixes the following sparse warning: drivers/usb/cdns3/host.c:58:5: warning: symbol 'cdns3_host_init' was not declared. Should it be static? Signed-off-by: Ben Dooks <[email protected]> Signed-off-by: Felipe Balbi <[email protected]>
2019-10-27usb: mtu3: fix missing include of mtu3_dr.hBen Dooks (Codethink)1-0/+1
The declarations of ssusb_gadget_{init,exit} are in the mtu3_dr.h file but the code does that implements them does not include this. Add the include to fix the following sparse warnigns: drivers/usb/mtu3/mtu3_core.c:825:5: warning: symbol 'ssusb_gadget_init' was not declared. Should it be static? drivers/usb/mtu3/mtu3_core.c:925:6: warning: symbol 'ssusb_gadget_exit' was not declared. Should it be static? Acked-by: Chunfeng Yun <[email protected]> Signed-off-by: Ben Dooks <[email protected]> Signed-off-by: Felipe Balbi <[email protected]>
2019-10-27usb: fsl: Check memory resource before releasing itNikhil Badola1-1/+1
Check memory resource existence before releasing it to avoid NULL pointer dereference Signed-off-by: Nikhil Badola <[email protected]> Reviewed-by: Ran Wang <[email protected]> Reviewed-by: Peter Chen <[email protected]> Signed-off-by: Felipe Balbi <[email protected]>
2019-10-27usb: dwc3: select CONFIG_REGMAP_MMIOArnd Bergmann1-0/+1
After many randconfig builds, one configuration caused a link error with dwc3-meson-g12a lacking the regmap-mmio code: drivers/usb/dwc3/dwc3-meson-g12a.o: In function `dwc3_meson_g12a_probe': dwc3-meson-g12a.c:(.text+0x9f): undefined reference to `__devm_regmap_init_mmio_clk' Add the select statement that we have for all other users of that dependency. Fixes: c99993376f72 ("usb: dwc3: Add Amlogic G12A DWC3 glue") Acked-by: Neil Armstrong <[email protected]> Signed-off-by: Arnd Bergmann <[email protected]> Signed-off-by: Felipe Balbi <[email protected]>
2019-10-26Merge git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpfDavid S. Miller7-16/+66
Daniel Borkmann says: ==================== pull-request: bpf 2019-10-27 The following pull-request contains BPF updates for your *net* tree. We've added 7 non-merge commits during the last 11 day(s) which contain a total of 7 files changed, 66 insertions(+), 16 deletions(-). The main changes are: 1) Fix two use-after-free bugs in relation to RCU in jited symbol exposure to kallsyms, from Daniel Borkmann. 2) Fix NULL pointer dereference in AF_XDP rx-only sockets, from Magnus Karlsson. 3) Fix hang in netdev unregister for hash based devmap as well as another overflow bug on 32 bit archs in memlock cost calculation, from Toke Høiland-Jørgensen. 4) Fix wrong memory access in LWT BPF programs on reroute due to invalid dst. Also fix BPF selftests to use more compatible nc options, from Jiri Benc. ==================== Signed-off-by: David S. Miller <[email protected]>
2019-10-26Merge tag 'mips_fixes_5.4_3' of ↵Linus Torvalds7-25/+35
git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux Pull MIPS fixes from Paul Burton: "A few MIPS fixes: - Fix VDSO time-related function behavior for systems where we need to fall back to syscalls, but were instead returning bogus results. - A fix to TLB exception handlers for Cavium Octeon systems where they would inadvertently clobber the $1/$at register. - A build fix for bcm63xx configurations. - Switch to using my @kernel.org email address" * tag 'mips_fixes_5.4_3' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: MIPS: tlbex: Fix build_restore_pagemask KScratch restore MIPS: bmips: mark exception vectors as char arrays mips: vdso: Fix __arch_get_hw_counter() MAINTAINERS: Use @kernel.org address for Paul Burton
2019-10-26Merge tag 'tty-5.4-rc5' of ↵Linus Torvalds1-4/+4
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty Pull tty/serial driver fix from Greg KH: "Here is a single tty/serial driver fix for 5.4-rc5 that resolves a reported issue. It has been in linux-next for a while with no problems" * tag 'tty-5.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: 8250-men-mcb: fix error checking when get_num_ports returns -ENODEV
2019-10-26Merge tag 'staging-5.4-rc5' of ↵Linus Torvalds1-4/+2
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging Pull staging driver fix from Greg KH: "Here is a single staging driver fix, for the wlan-ng driver, that resolves a reported issue. It is been in linux-next for a while with no reported issues" * tag 'staging-5.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: staging: wlan-ng: fix exit return when sme->key_idx >= NUM_WEPKEYS
2019-10-26Merge tag 'driver-core-5.4-rc5' of ↵Linus Torvalds1-2/+2
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core Pull driver core fix from Greg KH: "Here is a single sysfs fix for 5.4-rc5. It resolves an error if you actually try to use the __BIN_ATTR_WO() macro, seems I never tested it properly before :( This has been in linux-next for a while with no reported issues" * tag 'driver-core-5.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: sysfs: Fixes __BIN_ATTR_WO() macro
2019-10-26Merge tag 'char-misc-5.4-rc5' of ↵Linus Torvalds2-9/+4
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc Pull binder fix from Greg KH: "This is a single binder fix to resolve a reported issue by Jann. It's been in linux-next for a while with no reported issues" * tag 'char-misc-5.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: binder: Don't modify VMA bounds in ->mmap handler
2019-10-26Merge tag 'usb-5.4-rc5' of ↵Linus Torvalds7-44/+47
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb Pull USB fixes from Greg KH: "Here are a number of small USB driver fixes for 5.4-rc5. More "fun" with some of the misc USB drivers as found by syzbot, and there are a number of other small bugfixes in here for reported issues. All have been in linux-next for a while with no reported issues" * tag 'usb-5.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: usb: cdns3: Error out if USB_DR_MODE_UNKNOWN in cdns3_core_init_role() USB: ldusb: fix read info leaks USB: serial: ti_usb_3410_5052: clean up serial data access USB: serial: ti_usb_3410_5052: fix port-close races USB: usblp: fix use-after-free on disconnect usb: udc: lpc32xx: fix bad bit shift operation usb: cdns3: Fix dequeue implementation. USB: legousbtower: fix a signedness bug in tower_probe() USB: legousbtower: fix memleak on disconnect USB: ldusb: fix memleak on disconnect
2019-10-26Merge branch 'i2c/for-current-fixed' of ↵Linus Torvalds3-29/+48
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux Pull i2c fixes from Wolfram Sang: "A few driver fixes for the I2C subsystem" * 'i2c/for-current-fixed' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: i2c: stm32f7: remove warning when compiling with W=1 i2c: stm32f7: fix a race in slave mode with arbitration loss irq i2c: stm32f7: fix first byte to send in slave mode i2c: mt65xx: fix NULL ptr dereference i2c: aspeed: fix master pending state handling
2019-10-26Merge tag 'for-linus-2019-10-26' of git://git.kernel.dk/linux-blockLinus Torvalds3-125/+161
Pull block and io_uring fixes from Jens Axboe: "A bit bigger than usual at this point in time, mostly due to some good bug hunting work by Pavel that resulted in three io_uring fixes from him and two from me. Anyway, this pull request contains: - Revert of the submit-and-wait optimization for io_uring, it can't always be done safely. It depends on commands always making progress on their own, which isn't necessarily the case outside of strict file IO. (me) - Series of two patches from me and three from Pavel, fixing issues with shared data and sequencing for io_uring. - Lastly, two timeout sequence fixes for io_uring (zhangyi) - Two nbd patches fixing races (Josef) - libahci regulator_get_optional() fix (Mark)" * tag 'for-linus-2019-10-26' of git://git.kernel.dk/linux-block: nbd: verify socket is supported during setup ata: libahci_platform: Fix regulator_get_optional() misuse nbd: handle racing with error'ed out commands nbd: protect cmd->status with cmd->lock io_uring: fix bad inflight accounting for SETUP_IOPOLL|SETUP_SQTHREAD io_uring: used cached copies of sq->dropped and cq->overflow io_uring: Fix race for sqes with userspace io_uring: Fix broken links with offloading io_uring: Fix corrupted user_data io_uring: correct timeout req sequence when inserting a new entry io_uring : correct timeout req sequence when waiting timeout io_uring: revert "io_uring: optimize submit_and_wait API"
2019-10-26Merge branch 'ipv4-fix-route-update-on-metric-change'David S. Miller2-1/+22
Paolo Abeni says: ==================== ipv4: fix route update on metric change. This fixes connected route update on some edge cases for ip addr metric change. It additionally includes self tests for the covered scenarios. The new tests fail on unpatched kernels and pass on the patched one. v1 -> v2: - add selftests ==================== Signed-off-by: David S. Miller <[email protected]>
2019-10-26selftests: fib_tests: add more tests for metric updatePaolo Abeni1-0/+21
This patch adds two more tests to ipv4_addr_metric_test() to explicitly cover the scenarios fixed by the previous patch. Suggested-by: David Ahern <[email protected]> Signed-off-by: Paolo Abeni <[email protected]> Reviewed-by: David Ahern <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2019-10-26ipv4: fix route update on metric change.Paolo Abeni1-1/+1
Since commit af4d768ad28c ("net/ipv4: Add support for specifying metric of connected routes"), when updating an IP address with a different metric, the associated connected route is updated, too. Still, the mentioned commit doesn't handle properly some corner cases: $ ip addr add dev eth0 192.168.1.0/24 $ ip addr add dev eth0 192.168.2.1/32 peer 192.168.2.2 $ ip addr add dev eth0 192.168.3.1/24 $ ip addr change dev eth0 192.168.1.0/24 metric 10 $ ip addr change dev eth0 192.168.2.1/32 peer 192.168.2.2 metric 10 $ ip addr change dev eth0 192.168.3.1/24 metric 10 $ ip -4 route 192.168.1.0/24 dev eth0 proto kernel scope link src 192.168.1.0 192.168.2.2 dev eth0 proto kernel scope link src 192.168.2.1 192.168.3.0/24 dev eth0 proto kernel scope link src 192.168.2.1 metric 10 Only the last route is correctly updated. The problem is the current test in fib_modify_prefix_metric(): if (!(dev->flags & IFF_UP) || ifa->ifa_flags & (IFA_F_SECONDARY | IFA_F_NOPREFIXROUTE) || ipv4_is_zeronet(prefix) || prefix == ifa->ifa_local || ifa->ifa_prefixlen == 32) Which should be the logical 'not' of the pre-existing test in fib_add_ifaddr(): if (!ipv4_is_zeronet(prefix) && !(ifa->ifa_flags & IFA_F_SECONDARY) && (prefix != addr || ifa->ifa_prefixlen < 32)) To properly negate the original expression, we need to change the last logical 'or' to a logical 'and'. Fixes: af4d768ad28c ("net/ipv4: Add support for specifying metric of connected routes") Reported-and-suggested-by: Beniamino Galvani <[email protected]> Signed-off-by: Paolo Abeni <[email protected]> Reviewed-by: David Ahern <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2019-10-26net: Zeroing the structure ethtool_wolinfo in ethtool_get_wol()zhanglin1-1/+3
memset() the structure ethtool_wolinfo that has padded bytes but the padded bytes have not been zeroed out. Signed-off-by: zhanglin <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2019-10-26Merge tag 'ipvs-fixes-for-v5.4' of ↵Pablo Neira Ayuso6-25/+36
https://git.kernel.org/pub/scm/linux/kernel/git/horms/ipvs Simon Horman says: ==================== IPVS fixes for v5.4 * Eric Dumazet resolves a race condition in switching the defense level * Davide Caratti resolves a race condition in module removal ==================== Signed-off-by: Pablo Neira Ayuso <[email protected]>
2019-10-26Merge tag 's390-5.4-5' of ↵Linus Torvalds3-5/+13
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux Pull s390 fixes from Vasily Gorbik: - Add R_390_GLOB_DAT relocation type support. This fixes boot problem on linux-next. - Fix memory leak in zcrypt * tag 's390-5.4-5' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: s390/kaslr: add support for R_390_GLOB_DAT relocation type s390/zcrypt: fix memleak at release
2019-10-26Merge tag 'for-linus-5.4-rc5-tag' of ↵Linus Torvalds1-0/+8
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip Pull xen fixlet from Juergen Gross: "Just one patch for issuing a deprecation warning for 32-bit Xen pv guests" * tag 'for-linus-5.4-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: xen: issue deprecation warning for 32-bit pv guest
2019-10-26Merge tag 'dma-mapping-5.4-2' of git://git.infradead.org/users/hch/dma-mappingLinus Torvalds1-1/+9
Pull dma-mapping fix from Christoph Hellwig: "Fix a regression in the intel-iommu get_required_mask conversion (Arvind Sankar)" * tag 'dma-mapping-5.4-2' of git://git.infradead.org/users/hch/dma-mapping: iommu/vt-d: Return the correct dma mask when we are bypassing the IOMMU
2019-10-26Merge tag 'dax-fix-5.4-rc5' of ↵Linus Torvalds1-2/+3
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm Pull dax fix from Dan Williams: "Fix a performance regression that followed from a fix to the conversion of the fsdax implementation to the xarray. v5.3 users report that they stop seeing huge page mappings on an application + filesystem layout that was seeing huge pages previously on v5.2" * tag 'dax-fix-5.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: fs/dax: Fix pmd vs pte conflict detection
2019-10-26ALSA: bebob: Fix prototype of helper function to return negative valueTakashi Sakamoto1-2/+1
A helper function of ALSA bebob driver returns negative value in a function which has a prototype to return unsigned value. This commit fixes it by changing the prototype. Fixes: eb7b3a056cd8 ("ALSA: bebob: Add commands and connections/streams management") Cc: <[email protected]> # v3.16+ Signed-off-by: Takashi Sakamoto <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Takashi Iwai <[email protected]>
2019-10-25cxgb4: request the TX CIDX updates to status pageRaju Rangoju1-6/+2
For adapters which support the SGE Doorbell Queue Timer facility, we configured the Ethernet TX Queues to send CIDX Updates to the Associated Ethernet RX Response Queue with CPL_SGE_EGR_UPDATE messages to allow us to respond more quickly to the CIDX Updates. But, this was adding load to PCIe Link RX bandwidth and, potentially, resulting in higher CPU Interrupt load. This patch requests the HW to deliver the CIDX updates to the TX queue status page rather than generating an ingress queue message (as an interrupt). With this patch, the load on RX bandwidth is reduced and a substantial improvement in BW is noticed at lower IO sizes. Fixes: d429005fdf2c ("cxgb4/cxgb4vf: Add support for SGE doorbell queue timer") Signed-off-by: Raju Rangoju <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2019-10-25netns: fix GFP flags in rtnl_net_notifyid()Guillaume Nault5-26/+29
In rtnl_net_notifyid(), we certainly can't pass a null GFP flag to rtnl_notify(). A GFP_KERNEL flag would be fine in most circumstances, but there are a few paths calling rtnl_net_notifyid() from atomic context or from RCU critical sections. The later also precludes the use of gfp_any() as it wouldn't detect the RCU case. Also, the nlmsg_new() call is wrong too, as it uses GFP_KERNEL unconditionally. Therefore, we need to pass the GFP flags as parameter and propagate it through function calls until the proper flags can be determined. In most cases, GFP_KERNEL is fine. The exceptions are: * openvswitch: ovs_vport_cmd_get() and ovs_vport_cmd_dump() indirectly call rtnl_net_notifyid() from RCU critical section, * rtnetlink: rtmsg_ifinfo_build_skb() already receives GFP flags as parameter. Also, in ovs_vport_cmd_build_info(), let's change the GFP flags used by nlmsg_new(). The function is allowed to sleep, so better make the flags consistent with the ones used in the following ovs_vport_cmd_fill_info() call. Found by code inspection. Fixes: 9a9634545c70 ("netns: notify netns id events") Signed-off-by: Guillaume Nault <[email protected]> Acked-by: Nicolas Dichtel <[email protected]> Acked-by: Pravin B Shelar <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2019-10-25net: ethernet: Use the correct style for SPDX License IdentifierNishad Kamdar1-1/+1
This patch corrects the SPDX License Identifier style in header file related to ethernet driver for Cortina Gemini devices. For C header files Documentation/process/license-rules.rst mandates C-like comments (opposed to C source files where C++ style should be used) Changes made by using a script provided by Joe Perches here: https://lkml.org/lkml/2019/2/7/46. Suggested-by: Joe Perches <[email protected]> Signed-off-by: Nishad Kamdar <[email protected]> Acked-by: Linus Walleij <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2019-10-25Merge branch 'smc-fixes'David S. Miller1-1/+8
Karsten Graul says: ==================== net/smc: fixes for -net Fixes for the net tree, covering a memleak when closing SMC fallback sockets and fix SMC-R connection establishment when vlan-ids are used. ==================== Signed-off-by: David S. Miller <[email protected]>
2019-10-25net/smc: keep vlan_id for SMC-R in smc_listen_work()Ursula Braun1-1/+1
Creating of an SMC-R connection with vlan-id fails, because smc_listen_work() determines the vlan_id of the connection, saves it in struct smc_init_info ini, but clears the ini area again if SMC-D is not applicable. This patch just resets the ISM device before investigating SMC-R availability. Fixes: bc36d2fc93eb ("net/smc: consolidate function parameters") Signed-off-by: Ursula Braun <[email protected]> Signed-off-by: Karsten Graul <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2019-10-25net/smc: fix closing of fallback SMC socketsUrsula Braun1-0/+7
For SMC sockets forced to fallback to TCP, the file is propagated from the outer SMC to the internal TCP socket. When closing the SMC socket, the internal TCP socket file pointer must be restored to the original NULL value, otherwise memory leaks may show up (found with CONFIG_DEBUG_KMEMLEAK). The internal TCP socket is released in smc_clcsock_release(), which calls __sock_release() function in net/socket.c. This calls the needed iput(SOCK_INODE(sock)) only, if the file pointer has been reset to the original NULL-value. Fixes: 07603b230895 ("net/smc: propagate file from SMC to TCP socket") Signed-off-by: Ursula Braun <[email protected]> Signed-off-by: Karsten Graul <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2019-10-25Merge tag 'scsi-fixes' of ↵Linus Torvalds10-36/+36
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi Pull SCSI fixes from James Bottomley: "Nine changes, eight to drivers (qla2xxx, hpsa, lpfc, alua, ch, 53c710[x2], target) and one core change that tries to close a race between sysfs delete and module removal" * tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: scsi: lpfc: remove left-over BUILD_NVME defines scsi: core: try to get module before removing device scsi: hpsa: add missing hunks in reset-patch scsi: target: core: Do not overwrite CDB byte 1 scsi: ch: Make it possible to open a ch device multiple times again scsi: fix kconfig dependency warning related to 53C700_LE_ON_BE scsi: sni_53c710: fix compilation error scsi: scsi_dh_alua: handle RTPG sense code correctly during state transitions scsi: qla2xxx: fix a potential NULL pointer dereference
2019-10-25riscv: cleanup do_trap_breakChristoph Hellwig1-20/+6
If we always compile the get_break_insn_length inline function we can remove the ifdefs and let dead code elimination take care of the warn branch that is now unreadable because the report_bug stub always returns BUG_TRAP_TYPE_BUG. Signed-off-by: Christoph Hellwig <[email protected]> Reviewed-by: Anup Patel <[email protected]> Signed-off-by: Paul Walmsley <[email protected]>
2019-10-25net: hwbm: if CONFIG_NET_HWBM unset, make stub functions staticBen Dooks (Codethink)1-3/+7
If CONFIG_NET_HWBM is not set, then these stub functions in <net/hwbm.h> should be declared static to avoid trying to export them from any driver that includes this. Fixes the following sparse warnings: ./include/net/hwbm.h:24:6: warning: symbol 'hwbm_buf_free' was not declared. Should it be static? ./include/net/hwbm.h:25:5: warning: symbol 'hwbm_pool_refill' was not declared. Should it be static? ./include/net/hwbm.h:26:5: warning: symbol 'hwbm_pool_add' was not declared. Should it be static? Signed-off-by: Ben Dooks (Codethink) <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2019-10-25net: mvneta: make stub functions static inlineBen Dooks (Codethink)1-12/+20
If the CONFIG_MVNET_BA is not set, then make the stub functions static inline to avoid trying to export them, and remove hte following sparse warnings: drivers/net/ethernet/marvell/mvneta_bm.h:163:6: warning: symbol 'mvneta_bm_pool_destroy' was not declared. Should it be static? drivers/net/ethernet/marvell/mvneta_bm.h:165:6: warning: symbol 'mvneta_bm_bufs_free' was not declared. Should it be static? drivers/net/ethernet/marvell/mvneta_bm.h:167:5: warning: symbol 'mvneta_bm_construct' was not declared. Should it be static? drivers/net/ethernet/marvell/mvneta_bm.h:168:5: warning: symbol 'mvneta_bm_pool_refill' was not declared. Should it be static? drivers/net/ethernet/marvell/mvneta_bm.h:170:23: warning: symbol 'mvneta_bm_pool_use' was not declared. Should it be static? drivers/net/ethernet/marvell/mvneta_bm.h:181:18: warning: symbol 'mvneta_bm_get' was not declared. Should it be static? drivers/net/ethernet/marvell/mvneta_bm.h:182:6: warning: symbol 'mvneta_bm_put' was not declared. Should it be static? Signed-off-by: Ben Dooks (Codethink) <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2019-10-25net: sch_generic: Use pfifo_fast as fallback scheduler for CAN hardwareVincent Prince1-0/+2
There is networking hardware that isn't based on Ethernet for layers 1 and 2. For example CAN. CAN is a multi-master serial bus standard for connecting Electronic Control Units [ECUs] also known as nodes. A frame on the CAN bus carries up to 8 bytes of payload. Frame corruption is detected by a CRC. However frame loss due to corruption is possible, but a quite unusual phenomenon. While fq_codel works great for TCP/IP, it doesn't for CAN. There are a lot of legacy protocols on top of CAN, which are not build with flow control or high CAN frame drop rates in mind. When using fq_codel, as soon as the queue reaches a certain delay based length, skbs from the head of the queue are silently dropped. Silently meaning that the user space using a send() or similar syscall doesn't get an error. However TCP's flow control algorithm will detect dropped packages and adjust the bandwidth accordingly. When using fq_codel and sending raw frames over CAN, which is the common use case, the user space thinks the package has been sent without problems, because send() returned without an error. pfifo_fast will drop skbs, if the queue length exceeds the maximum. But with this scheduler the skbs at the tail are dropped, an error (-ENOBUFS) is propagated to user space. So that the user space can slow down the package generation. On distributions, where fq_codel is made default via CONFIG_DEFAULT_NET_SCH during compile time, or set default during runtime with sysctl net.core.default_qdisc (see [1]), we get a bad user experience. In my test case with pfifo_fast, I can transfer thousands of million CAN frames without a frame drop. On the other hand with fq_codel there is more then one lost CAN frame per thousand frames. As pointed out fq_codel is not suited for CAN hardware, so this patch changes attach_one_default_qdisc() to use pfifo_fast for "ARPHRD_CAN" network devices. During transition of a netdev from down to up state the default queuing discipline is attached by attach_default_qdiscs() with the help of attach_one_default_qdisc(). This patch modifies attach_one_default_qdisc() to attach the pfifo_fast (pfifo_fast_ops) if the network device type is "ARPHRD_CAN". [1] https://github.com/systemd/systemd/issues/9194 Signed-off-by: Vincent Prince <[email protected]> Signed-off-by: David S. Miller <[email protected]>
2019-10-25Merge branch 'for-linus' of ↵Linus Torvalds1-2/+4
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input Pull input fix from Dmitry Torokhov: "A fix for st1232 driver to properly report coordinates for 2nd and subsequent fingers when more than one is on the surface" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: Input: st1232 - fix reporting multitouch coordinates
2019-10-25nbd: verify socket is supported during setupMike Christie1-2/+21
nbd requires socket families to support the shutdown method so the nbd recv workqueue can be woken up from its sock_recvmsg call. If the socket does not support the callout we will leave recv works running or get hangs later when the device or module is removed. This adds a check during socket connection/reconnection to make sure the socket being passed in supports the needed callout. Reported-by: [email protected] Fixes: e9e006f5fcf2 ("nbd: fix max number of supported devs") Tested-by: Richard W.M. Jones <[email protected]> Signed-off-by: Mike Christie <[email protected]> Signed-off-by: Jens Axboe <[email protected]>
2019-10-25ata: libahci_platform: Fix regulator_get_optional() misuseMark Brown1-24/+14
This driver is using regulator_get_optional() to handle all the supplies that it handles, and only ever enables and disables all supplies en masse without ever doing any other configuration of the device to handle missing power. These are clear signs that the API is being misused - it should only be used for supplies that may be physically absent from the system and in these cases the hardware usually needs different configuration if the supply is missing. Instead use normal regualtor_get(), if the supply is not described in DT then the framework will substitute a dummy regulator in so no special handling is needed by the consumer driver. In the case of the PHY regulator the handling in the driver is a hack to deal with integrated PHYs; the supplies are only optional in the sense that that there's some confusion in the code about where they're bound to. From a code point of view they function exactly as normal supplies so can be treated as such. It'd probably be better to model this by instantiating a PHY object for integrated PHYs. Reviewed-by: Hans de Goede <[email protected]> Signed-off-by: Mark Brown <[email protected]> Signed-off-by: Jens Axboe <[email protected]>
2019-10-25nbd: handle racing with error'ed out commandsJosef Bacik1-0/+6
We hit the following warning in production print_req_error: I/O error, dev nbd0, sector 7213934408 flags 80700 ------------[ cut here ]------------ refcount_t: underflow; use-after-free. WARNING: CPU: 25 PID: 32407 at lib/refcount.c:190 refcount_sub_and_test_checked+0x53/0x60 Workqueue: knbd-recv recv_work [nbd] RIP: 0010:refcount_sub_and_test_checked+0x53/0x60 Call Trace: blk_mq_free_request+0xb7/0xf0 blk_mq_complete_request+0x62/0xf0 recv_work+0x29/0xa1 [nbd] process_one_work+0x1f5/0x3f0 worker_thread+0x2d/0x3d0 ? rescuer_thread+0x340/0x340 kthread+0x111/0x130 ? kthread_create_on_node+0x60/0x60 ret_from_fork+0x1f/0x30 ---[ end trace b079c3c67f98bb7c ]--- This was preceded by us timing out everything and shutting down the sockets for the device. The problem is we had a request in the queue at the same time, so we completed the request twice. This can actually happen in a lot of cases, we fail to get a ref on our config, we only have one connection and just error out the command, etc. Fix this by checking cmd->status in nbd_read_stat. We only change this under the cmd->lock, so we are safe to check this here and see if we've already error'ed this command out, which would indicate that we've completed it as well. Reviewed-by: Mike Christie <[email protected]> Signed-off-by: Josef Bacik <[email protected]> Signed-off-by: Jens Axboe <[email protected]>
2019-10-25nbd: protect cmd->status with cmd->lockJosef Bacik1-5/+7
We already do this for the most part, except in timeout and clear_req. For the timeout case we take the lock after we grab a ref on the config, but that isn't really necessary because we're safe to touch the cmd at this point, so just move the order around. For the clear_req cause this is initiated by the user, so again is safe. Reviewed-by: Mike Christie <[email protected]> Signed-off-by: Josef Bacik <[email protected]> Signed-off-by: Jens Axboe <[email protected]>
2019-10-25Merge tag 'modules-for-v5.4-rc5' of ↵Linus Torvalds4-29/+47
git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux Pull modules fixes from Jessica Yu: - Revert __ksymtab_$namespace.$symbol naming scheme back to __ksymtab_$symbol, as it was causing issues with depmod. Instead, have modpost extract a symbol's namespace from __kstrtabns and __ksymtab_strings. - Fix `make nsdeps` for out of tree kernel builds (make O=...) caused by unescaped '/'. Use a different sed delimiter to avoid this problem. * tag 'modules-for-v5.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux: scripts/nsdeps: use alternative sed delimiter symbol namespaces: revert to previous __ksymtab name scheme modpost: make updating the symbol namespace explicit modpost: delegate updating namespaces to separate function
2019-10-25Merge tag 'armsoc-fixes' of ↵Linus Torvalds40-107/+145
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc Pull ARM SoC fixes from Olof Johansson: "A slightly larger set of fixes have accrued in the last two weeks. Mostly a collection of the usual smaller fixes: - Marvell Armada: USB phy setup issues on Turris Mox - Broadcom: GPIO/pinmux DT mapping corrections for Stingray, MMC bus width fix for RPi Zero W, GPIO LED removal for RPI CM3. Also some maintainer updates. - OMAP: Fixlets for display config, interrupt settings for wifi, some clock/PM pieces. Also IOMMU regression fix and a ti-sysc no-watchdog regression fix. - i.MX: A few fixes around PM/settings, some devicetree fixlets and catching up with config option changes in DRM - Rockchip: RockRro64 misc DT fixups, Hugsun X99 USB-C, Kevin display panel settings ... and some smaller fixes for Davinci (backlight, McBSP DMA), Allwinner (phy regulators, PMU removal on A64, etc)" * tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (42 commits) ARM: dts: stm32: relax qspi pins slew-rate for stm32mp157 MAINTAINERS: Update the Spreadtrum SoC maintainer MAINTAINERS: Remove Gregory and Brian for ARCH_BRCMSTB ARM: dts: bcm2837-rpi-cm3: Avoid leds-gpio probing issue bus: ti-sysc: Fix watchdog quirk handling ARM: OMAP2+: Add pdata for OMAP3 ISP IOMMU ARM: OMAP2+: Plug in device_enable/idle ops for IOMMUs ARM: davinci_all_defconfig: enable GPIO backlight ARM: davinci: dm365: Fix McBSP dma_slave_map entry ARM: dts: bcm2835-rpi-zero-w: Fix bus-width of sdhci ARM: imx_v6_v7_defconfig: Enable CONFIG_DRM_MSM arm64: dts: imx8mn: Use correct clock for usdhc's ipg clk arm64: dts: imx8mm: Use correct clock for usdhc's ipg clk arm64: dts: imx8mq: Use correct clock for usdhc's ipg clk ARM: dts: imx7s: Correct GPT's ipg clock source ARM: dts: vf610-zii-scu4-aib: Specify 'i2c-mux-idle-disconnect' ARM: dts: imx6q-logicpd: Re-Enable SNVS power key arm64: dts: lx2160a: Correct CPU core idle state name mailmap: Add Simon Arlott (replacement for expired email address) arm64: dts: rockchip: Fix override mode for rk3399-kevin panel ...
Powered by cgit, Gruvboxed by Blaster4385.