diff options
Diffstat (limited to 'include/uapi/linux')
| -rw-r--r-- | include/uapi/linux/bpf.h | 11 | ||||
| -rw-r--r-- | include/uapi/linux/ethtool.h | 13 | ||||
| -rw-r--r-- | include/uapi/linux/ethtool_netlink.h | 1 | ||||
| -rw-r--r-- | include/uapi/linux/fcntl.h | 3 | ||||
| -rw-r--r-- | include/uapi/linux/fuse.h | 10 | ||||
| -rw-r--r-- | include/uapi/linux/if_link.h | 521 | ||||
| -rw-r--r-- | include/uapi/linux/if_xdp.h | 47 | ||||
| -rw-r--r-- | include/uapi/linux/mptcp_pm.h | 2 | ||||
| -rw-r--r-- | include/uapi/linux/netdev.h | 41 | ||||
| -rw-r--r-- | include/uapi/linux/stddef.h | 2 | ||||
| -rw-r--r-- | include/uapi/linux/v4l2-subdev.h | 2 |
11 files changed, 642 insertions, 11 deletions
diff --git a/include/uapi/linux/bpf.h b/include/uapi/linux/bpf.h index 7a5498242eaa..b1e8c5bdfc82 100644 --- a/include/uapi/linux/bpf.h +++ b/include/uapi/linux/bpf.h @@ -6563,6 +6563,16 @@ struct bpf_link_info { __u64 missed; } kprobe_multi; struct { + __aligned_u64 path; + __aligned_u64 offsets; + __aligned_u64 ref_ctr_offsets; + __aligned_u64 cookies; + __u32 path_size; /* in/out: real path size on success, including zero byte */ + __u32 count; /* in/out: uprobe_multi offsets/ref_ctr_offsets/cookies count */ + __u32 flags; + __u32 pid; + } uprobe_multi; + struct { __u32 type; /* enum bpf_perf_event_type */ __u32 :32; union { @@ -6892,6 +6902,7 @@ enum { BPF_TCP_LISTEN, BPF_TCP_CLOSING, /* Now a valid state */ BPF_TCP_NEW_SYN_RECV, + BPF_TCP_BOUND_INACTIVE, BPF_TCP_MAX_STATES /* Leave at the end! */ }; diff --git a/include/uapi/linux/ethtool.h b/include/uapi/linux/ethtool.h index f7fba0dc87e5..0787d561ace0 100644 --- a/include/uapi/linux/ethtool.h +++ b/include/uapi/linux/ethtool.h @@ -1266,6 +1266,8 @@ struct ethtool_rxfh_indir { * hardware hash key. * @hfunc: Defines the current RSS hash function used by HW (or to be set to). * Valid values are one of the %ETH_RSS_HASH_*. + * @input_xfrm: Defines how the input data is transformed. Valid values are one + * of %RXH_XFRM_*. * @rsvd8: Reserved for future use; see the note on reserved space. * @rsvd32: Reserved for future use; see the note on reserved space. * @rss_config: RX ring/queue index for each hash value i.e., indirection table @@ -1285,7 +1287,8 @@ struct ethtool_rxfh { __u32 indir_size; __u32 key_size; __u8 hfunc; - __u8 rsvd8[3]; + __u8 input_xfrm; + __u8 rsvd8[2]; __u32 rsvd32; __u32 rss_config[]; }; @@ -1992,6 +1995,14 @@ static inline int ethtool_validate_duplex(__u8 duplex) #define WOL_MODE_COUNT 8 +/* RSS hash function data + * XOR the corresponding source and destination fields of each specified + * protocol. Both copies of the XOR'ed fields are fed into the RSS and RXHASH + * calculation. Note that this XORing reduces the input set entropy and could + * be exploited to reduce the RSS queue spread. + */ +#define RXH_XFRM_SYM_XOR (1 << 0) + /* L2-L4 network traffic flow types */ #define TCP_V4_FLOW 0x01 /* hash or spec (tcp_ip4_spec) */ #define UDP_V4_FLOW 0x02 /* hash or spec (udp_ip4_spec) */ diff --git a/include/uapi/linux/ethtool_netlink.h b/include/uapi/linux/ethtool_netlink.h index 73e2c10dc2cc..3f89074aa06c 100644 --- a/include/uapi/linux/ethtool_netlink.h +++ b/include/uapi/linux/ethtool_netlink.h @@ -908,6 +908,7 @@ enum { ETHTOOL_A_RSS_HFUNC, /* u32 */ ETHTOOL_A_RSS_INDIR, /* binary */ ETHTOOL_A_RSS_HKEY, /* binary */ + ETHTOOL_A_RSS_INPUT_XFRM, /* u32 */ __ETHTOOL_A_RSS_CNT, ETHTOOL_A_RSS_MAX = (__ETHTOOL_A_RSS_CNT - 1), diff --git a/include/uapi/linux/fcntl.h b/include/uapi/linux/fcntl.h index 6c80f96049bd..282e90aeb163 100644 --- a/include/uapi/linux/fcntl.h +++ b/include/uapi/linux/fcntl.h @@ -116,5 +116,8 @@ #define AT_HANDLE_FID AT_REMOVEDIR /* file handle is needed to compare object identity and may not be usable to open_by_handle_at(2) */ +#if defined(__KERNEL__) +#define AT_GETATTR_NOSEC 0x80000000 +#endif #endif /* _UAPI_LINUX_FCNTL_H */ diff --git a/include/uapi/linux/fuse.h b/include/uapi/linux/fuse.h index db92a7202b34..e7418d15fe39 100644 --- a/include/uapi/linux/fuse.h +++ b/include/uapi/linux/fuse.h @@ -209,7 +209,7 @@ * - add FUSE_HAS_EXPIRE_ONLY * * 7.39 - * - add FUSE_DIRECT_IO_RELAX + * - add FUSE_DIRECT_IO_ALLOW_MMAP * - add FUSE_STATX and related structures */ @@ -409,8 +409,7 @@ struct fuse_file_lock { * FUSE_CREATE_SUPP_GROUP: add supplementary group info to create, mkdir, * symlink and mknod (single group that matches parent) * FUSE_HAS_EXPIRE_ONLY: kernel supports expiry-only entry invalidation - * FUSE_DIRECT_IO_RELAX: relax restrictions in FOPEN_DIRECT_IO mode, for now - * allow shared mmap + * FUSE_DIRECT_IO_ALLOW_MMAP: allow shared mmap in FOPEN_DIRECT_IO mode. */ #define FUSE_ASYNC_READ (1 << 0) #define FUSE_POSIX_LOCKS (1 << 1) @@ -449,7 +448,10 @@ struct fuse_file_lock { #define FUSE_HAS_INODE_DAX (1ULL << 33) #define FUSE_CREATE_SUPP_GROUP (1ULL << 34) #define FUSE_HAS_EXPIRE_ONLY (1ULL << 35) -#define FUSE_DIRECT_IO_RELAX (1ULL << 36) +#define FUSE_DIRECT_IO_ALLOW_MMAP (1ULL << 36) + +/* Obsolete alias for FUSE_DIRECT_IO_ALLOW_MMAP */ +#define FUSE_DIRECT_IO_RELAX FUSE_DIRECT_IO_ALLOW_MMAP /** * CUSE INIT request/reply flags diff --git a/include/uapi/linux/if_link.h b/include/uapi/linux/if_link.h index 8181ef23a7a2..ab9bcff96e4d 100644 --- a/include/uapi/linux/if_link.h +++ b/include/uapi/linux/if_link.h @@ -461,6 +461,286 @@ enum in6_addr_gen_mode { /* Bridge section */ +/** + * DOC: Bridge enum definition + * + * Please *note* that the timer values in the following section are expected + * in clock_t format, which is seconds multiplied by USER_HZ (generally + * defined as 100). + * + * @IFLA_BR_FORWARD_DELAY + * The bridge forwarding delay is the time spent in LISTENING state + * (before moving to LEARNING) and in LEARNING state (before moving + * to FORWARDING). Only relevant if STP is enabled. + * + * The valid values are between (2 * USER_HZ) and (30 * USER_HZ). + * The default value is (15 * USER_HZ). + * + * @IFLA_BR_HELLO_TIME + * The time between hello packets sent by the bridge, when it is a root + * bridge or a designated bridge. Only relevant if STP is enabled. + * + * The valid values are between (1 * USER_HZ) and (10 * USER_HZ). + * The default value is (2 * USER_HZ). + * + * @IFLA_BR_MAX_AGE + * The hello packet timeout is the time until another bridge in the + * spanning tree is assumed to be dead, after reception of its last hello + * message. Only relevant if STP is enabled. + * + * The valid values are between (6 * USER_HZ) and (40 * USER_HZ). + * The default value is (20 * USER_HZ). + * + * @IFLA_BR_AGEING_TIME + * Configure the bridge's FDB entries aging time. It is the time a MAC + * address will be kept in the FDB after a packet has been received from + * that address. After this time has passed, entries are cleaned up. + * Allow values outside the 802.1 standard specification for special cases: + * + * * 0 - entry never ages (all permanent) + * * 1 - entry disappears (no persistence) + * + * The default value is (300 * USER_HZ). + * + * @IFLA_BR_STP_STATE + * Turn spanning tree protocol on (*IFLA_BR_STP_STATE* > 0) or off + * (*IFLA_BR_STP_STATE* == 0) for this bridge. + * + * The default value is 0 (disabled). + * + * @IFLA_BR_PRIORITY + * Set this bridge's spanning tree priority, used during STP root bridge + * election. + * + * The valid values are between 0 and 65535. + * + * @IFLA_BR_VLAN_FILTERING + * Turn VLAN filtering on (*IFLA_BR_VLAN_FILTERING* > 0) or off + * (*IFLA_BR_VLAN_FILTERING* == 0). When disabled, the bridge will not + * consider the VLAN tag when handling packets. + * + * The default value is 0 (disabled). + * + * @IFLA_BR_VLAN_PROTOCOL + * Set the protocol used for VLAN filtering. + * + * The valid values are 0x8100(802.1Q) or 0x88A8(802.1AD). The default value + * is 0x8100(802.1Q). + * + * @IFLA_BR_GROUP_FWD_MASK + * The group forwarding mask. This is the bitmask that is applied to + * decide whether to forward incoming frames destined to link-local + * addresses (of the form 01:80:C2:00:00:0X). + * + * The default value is 0, which means the bridge does not forward any + * link-local frames coming on this port. + * + * @IFLA_BR_ROOT_ID + * The bridge root id, read only. + * + * @IFLA_BR_BRIDGE_ID + * The bridge id, read only. + * + * @IFLA_BR_ROOT_PORT + * The bridge root port, read only. + * + * @IFLA_BR_ROOT_PATH_COST + * The bridge root path cost, read only. + * + * @IFLA_BR_TOPOLOGY_CHANGE + * The bridge topology change, read only. + * + * @IFLA_BR_TOPOLOGY_CHANGE_DETECTED + * The bridge topology change detected, read only. + * + * @IFLA_BR_HELLO_TIMER + * The bridge hello timer, read only. + * + * @IFLA_BR_TCN_TIMER + * The bridge tcn timer, read only. + * + * @IFLA_BR_TOPOLOGY_CHANGE_TIMER + * The bridge topology change timer, read only. + * + * @IFLA_BR_GC_TIMER + * The bridge gc timer, read only. + * + * @IFLA_BR_GROUP_ADDR + * Set the MAC address of the multicast group this bridge uses for STP. + * The address must be a link-local address in standard Ethernet MAC address + * format. It is an address of the form 01:80:C2:00:00:0X, with X in [0, 4..f]. + * + * The default value is 0. + * + * @IFLA_BR_FDB_FLUSH + * Flush bridge's fdb dynamic entries. + * + * @IFLA_BR_MCAST_ROUTER + * Set bridge's multicast router if IGMP snooping is enabled. + * The valid values are: + * + * * 0 - disabled. + * * 1 - automatic (queried). + * * 2 - permanently enabled. + * + * The default value is 1. + * + * @IFLA_BR_MCAST_SNOOPING + * Turn multicast snooping on (*IFLA_BR_MCAST_SNOOPING* > 0) or off + * (*IFLA_BR_MCAST_SNOOPING* == 0). + * + * The default value is 1. + * + * @IFLA_BR_MCAST_QUERY_USE_IFADDR + * If enabled use the bridge's own IP address as source address for IGMP + * queries (*IFLA_BR_MCAST_QUERY_USE_IFADDR* > 0) or the default of 0.0.0.0 + * (*IFLA_BR_MCAST_QUERY_USE_IFADDR* == 0). + * + * The default value is 0 (disabled). + * + * @IFLA_BR_MCAST_QUERIER + * Enable (*IFLA_BR_MULTICAST_QUERIER* > 0) or disable + * (*IFLA_BR_MULTICAST_QUERIER* == 0) IGMP querier, ie sending of multicast + * queries by the bridge. + * + * The default value is 0 (disabled). + * + * @IFLA_BR_MCAST_HASH_ELASTICITY + * Set multicast database hash elasticity, It is the maximum chain length in + * the multicast hash table. This attribute is *deprecated* and the value + * is always 16. + * + * @IFLA_BR_MCAST_HASH_MAX + * Set maximum size of the multicast hash table + * + * The default value is 4096, the value must be a power of 2. + * + * @IFLA_BR_MCAST_LAST_MEMBER_CNT + * The Last Member Query Count is the number of Group-Specific Queries + * sent before the router assumes there are no local members. The Last + * Member Query Count is also the number of Group-and-Source-Specific + * Queries sent before the router assumes there are no listeners for a + * particular source. + * + * The default value is 2. + * + * @IFLA_BR_MCAST_STARTUP_QUERY_CNT + * The Startup Query Count is the number of Queries sent out on startup, + * separated by the Startup Query Interval. + * + * The default value is 2. + * + * @IFLA_BR_MCAST_LAST_MEMBER_INTVL + * The Last Member Query Interval is the Max Response Time inserted into + * Group-Specific Queries sent in response to Leave Group messages, and + * is also the amount of time between Group-Specific Query messages. + * + * The default value is (1 * USER_HZ). + * + * @IFLA_BR_MCAST_MEMBERSHIP_INTVL + * The interval after which the bridge will leave a group, if no membership + * reports for this group are received. + * + * The default value is (260 * USER_HZ). + * + * @IFLA_BR_MCAST_QUERIER_INTVL + * The interval between queries sent by other routers. if no queries are + * seen after this delay has passed, the bridge will start to send its own + * queries (as if *IFLA_BR_MCAST_QUERIER_INTVL* was enabled). + * + * The default value is (255 * USER_HZ). + * + * @IFLA_BR_MCAST_QUERY_INTVL + * The Query Interval is the interval between General Queries sent by + * the Querier. + * + * The default value is (125 * USER_HZ). The minimum value is (1 * USER_HZ). + * + * @IFLA_BR_MCAST_QUERY_RESPONSE_INTVL + * The Max Response Time used to calculate the Max Resp Code inserted + * into the periodic General Queries. + * + * The default value is (10 * USER_HZ). + * + * @IFLA_BR_MCAST_STARTUP_QUERY_INTVL + * The interval between queries in the startup phase. + * + * The default value is (125 * USER_HZ) / 4. The minimum value is (1 * USER_HZ). + * + * @IFLA_BR_NF_CALL_IPTABLES + * Enable (*NF_CALL_IPTABLES* > 0) or disable (*NF_CALL_IPTABLES* == 0) + * iptables hooks on the bridge. + * + * The default value is 0 (disabled). + * + * @IFLA_BR_NF_CALL_IP6TABLES + * Enable (*NF_CALL_IP6TABLES* > 0) or disable (*NF_CALL_IP6TABLES* == 0) + * ip6tables hooks on the bridge. + * + * The default value is 0 (disabled). + * + * @IFLA_BR_NF_CALL_ARPTABLES + * Enable (*NF_CALL_ARPTABLES* > 0) or disable (*NF_CALL_ARPTABLES* == 0) + * arptables hooks on the bridge. + * + * The default value is 0 (disabled). + * + * @IFLA_BR_VLAN_DEFAULT_PVID + * VLAN ID applied to untagged and priority-tagged incoming packets. + * + * The default value is 1. Setting to the special value 0 makes all ports of + * this bridge not have a PVID by default, which means that they will + * not accept VLAN-untagged traffic. + * + * @IFLA_BR_PAD + * Bridge attribute padding type for netlink message. + * + * @IFLA_BR_VLAN_STATS_ENABLED + * Enable (*IFLA_BR_VLAN_STATS_ENABLED* == 1) or disable + * (*IFLA_BR_VLAN_STATS_ENABLED* == 0) per-VLAN stats accounting. + * + * The default value is 0 (disabled). + * + * @IFLA_BR_MCAST_STATS_ENABLED + * Enable (*IFLA_BR_MCAST_STATS_ENABLED* > 0) or disable + * (*IFLA_BR_MCAST_STATS_ENABLED* == 0) multicast (IGMP/MLD) stats + * accounting. + * + * The default value is 0 (disabled). + * + * @IFLA_BR_MCAST_IGMP_VERSION + * Set the IGMP version. + * + * The valid values are 2 and 3. The default value is 2. + * + * @IFLA_BR_MCAST_MLD_VERSION + * Set the MLD version. + * + * The valid values are 1 and 2. The default value is 1. + * + * @IFLA_BR_VLAN_STATS_PER_PORT + * Enable (*IFLA_BR_VLAN_STATS_PER_PORT* == 1) or disable + * (*IFLA_BR_VLAN_STATS_PER_PORT* == 0) per-VLAN per-port stats accounting. + * Can be changed only when there are no port VLANs configured. + * + * The default value is 0 (disabled). + * + * @IFLA_BR_MULTI_BOOLOPT + * The multi_boolopt is used to control new boolean options to avoid adding + * new netlink attributes. You can look at ``enum br_boolopt_id`` for those + * options. + * + * @IFLA_BR_MCAST_QUERIER_STATE + * Bridge mcast querier states, read only. + * + * @IFLA_BR_FDB_N_LEARNED + * The number of dynamically learned FDB entries for the current bridge, + * read only. + * + * @IFLA_BR_FDB_MAX_LEARNED + * Set the number of max dynamically learned FDB entries for the current + * bridge. + */ enum { IFLA_BR_UNSPEC, IFLA_BR_FORWARD_DELAY, @@ -522,11 +802,252 @@ struct ifla_bridge_id { __u8 addr[6]; /* ETH_ALEN */ }; +/** + * DOC: Bridge mode enum definition + * + * @BRIDGE_MODE_HAIRPIN + * Controls whether traffic may be sent back out of the port on which it + * was received. This option is also called reflective relay mode, and is + * used to support basic VEPA (Virtual Ethernet Port Aggregator) + * capabilities. By default, this flag is turned off and the bridge will + * not forward traffic back out of the receiving port. + */ enum { BRIDGE_MODE_UNSPEC, BRIDGE_MODE_HAIRPIN, }; +/** + * DOC: Bridge port enum definition + * + * @IFLA_BRPORT_STATE + * The operation state of the port. Here are the valid values. + * + * * 0 - port is in STP *DISABLED* state. Make this port completely + * inactive for STP. This is also called BPDU filter and could be used + * to disable STP on an untrusted port, like a leaf virtual device. + * The traffic forwarding is also stopped on this port. + * * 1 - port is in STP *LISTENING* state. Only valid if STP is enabled + * on the bridge. In this state the port listens for STP BPDUs and + * drops all other traffic frames. + * * 2 - port is in STP *LEARNING* state. Only valid if STP is enabled on + * the bridge. In this state the port will accept traffic only for the + * purpose of updating MAC address tables. + * * 3 - port is in STP *FORWARDING* state. Port is fully active. + * * 4 - port is in STP *BLOCKING* state. Only valid if STP is enabled on + * the bridge. This state is used during the STP election process. + * In this state, port will only process STP BPDUs. + * + * @IFLA_BRPORT_PRIORITY + * The STP port priority. The valid values are between 0 and 255. + * + * @IFLA_BRPORT_COST + * The STP path cost of the port. The valid values are between 1 and 65535. + * + * @IFLA_BRPORT_MODE + * Set the bridge port mode. See *BRIDGE_MODE_HAIRPIN* for more details. + * + * @IFLA_BRPORT_GUARD + * Controls whether STP BPDUs will be processed by the bridge port. By + * default, the flag is turned off to allow BPDU processing. Turning this + * flag on will disable the bridge port if a STP BPDU packet is received. + * + * If the bridge has Spanning Tree enabled, hostile devices on the network + * may send BPDU on a port and cause network failure. Setting *guard on* + * will detect and stop this by disabling the port. The port will be + * restarted if the link is brought down, or removed and reattached. + * + * @IFLA_BRPORT_PROTECT + * Controls whether a given port is allowed to become a root port or not. + * Only used when STP is enabled on the bridge. By default the flag is off. + * + * This feature is also called root port guard. If BPDU is received from a + * leaf (edge) port, it should not be elected as root port. This could + * be used if using STP on a bridge and the downstream bridges are not fully + * trusted; this prevents a hostile guest from rerouting traffic. + * + * @IFLA_BRPORT_FAST_LEAVE + * This flag allows the bridge to immediately stop multicast traffic + * forwarding on a port that receives an IGMP Leave message. It is only used + * when IGMP snooping is enabled on the bridge. By default the flag is off. + * + * @IFLA_BRPORT_LEARNING + * Controls whether a given port will learn *source* MAC addresses from + * received traffic or not. Also controls whether dynamic FDB entries + * (which can also be added by software) will be refreshed by incoming + * traffic. By default this flag is on. + * + * @IFLA_BRPORT_UNICAST_FLOOD + * Controls whether unicast traffic for which there is no FDB entry will + * be flooded towards this port. By default this flag is on. + * + * @IFLA_BRPORT_PROXYARP + * Enable proxy ARP on this port. + * + * @IFLA_BRPORT_LEARNING_SYNC + * Controls whether a given port will sync MAC addresses learned on device + * port to bridge FDB. + * + * @IFLA_BRPORT_PROXYARP_WIFI + * Enable proxy ARP on this port which meets extended requirements by + * IEEE 802.11 and Hotspot 2.0 specifications. + * + * @IFLA_BRPORT_ROOT_ID + * + * @IFLA_BRPORT_BRIDGE_ID + * + * @IFLA_BRPORT_DESIGNATED_PORT + * + * @IFLA_BRPORT_DESIGNATED_COST + * + * @IFLA_BRPORT_ID + * + * @IFLA_BRPORT_NO + * + * @IFLA_BRPORT_TOPOLOGY_CHANGE_ACK + * + * @IFLA_BRPORT_CONFIG_PENDING + * + * @IFLA_BRPORT_MESSAGE_AGE_TIMER + * + * @IFLA_BRPORT_FORWARD_DELAY_TIMER + * + * @IFLA_BRPORT_HOLD_TIMER + * + * @IFLA_BRPORT_FLUSH + * Flush bridge ports' fdb dynamic entries. + * + * @IFLA_BRPORT_MULTICAST_ROUTER + * Configure the port's multicast router presence. A port with + * a multicast router will receive all multicast traffic. + * The valid values are: + * + * * 0 disable multicast routers on this port + * * 1 let the system detect the presence of routers (default) + * * 2 permanently enable multicast traffic forwarding on this port + * * 3 enable multicast routers temporarily on this port, not depending + * on incoming queries. + * + * @IFLA_BRPORT_PAD + * + * @IFLA_BRPORT_MCAST_FLOOD + * Controls whether a given port will flood multicast traffic for which + * there is no MDB entry. By default this flag is on. + * + * @IFLA_BRPORT_MCAST_TO_UCAST + * Controls whether a given port will replicate packets using unicast + * instead of multicast. By default this flag is off. + * + * This is done by copying the packet per host and changing the multicast + * destination MAC to a unicast one accordingly. + * + * *mcast_to_unicast* works on top of the multicast snooping feature of the + * bridge. Which means unicast copies are only delivered to hosts which + * are interested in unicast and signaled this via IGMP/MLD reports previously. + * + * This feature is intended for interface types which have a more reliable + * and/or efficient way to deliver unicast packets than broadcast ones + * (e.g. WiFi). + * + * However, it should only be enabled on interfaces where no IGMPv2/MLDv1 + * report suppression takes place. IGMP/MLD report suppression issue is + * usually overcome by the network daemon (supplicant) enabling AP isolation + * and by that separating all STAs. + * + * Delivery of STA-to-STA IP multicast is made possible again by enabling + * and utilizing the bridge hairpin mode, which considers the incoming port + * as a potential outgoing port, too (see *BRIDGE_MODE_HAIRPIN* option). + * Hairpin mode is performed after multicast snooping, therefore leading + * to only deliver reports to STAs running a multicast router. + * + * @IFLA_BRPORT_VLAN_TUNNEL + * Controls whether vlan to tunnel mapping is enabled on the port. + * By default this flag is off. + * + * @IFLA_BRPORT_BCAST_FLOOD + * Controls flooding of broadcast traffic on the given port. By default + * this flag is on. + * + * @IFLA_BRPORT_GROUP_FWD_MASK + * Set the group forward mask. This is a bitmask that is applied to + * decide whether to forward incoming frames destined to link-local + * addresses. The addresses of the form are 01:80:C2:00:00:0X (defaults + * to 0, which means the bridge does not forward any link-local frames + * coming on this port). + * + * @IFLA_BRPORT_NEIGH_SUPPRESS + * Controls whether neighbor discovery (arp and nd) proxy and suppression + * is enabled on the port. By default this flag is off. + * + * @IFLA_BRPORT_ISOLATED + * Controls whether a given port will be isolated, which means it will be + * able to communicate with non-isolated ports only. By default this + * flag is off. + * + * @IFLA_BRPORT_BACKUP_PORT + * Set a backup port. If the port loses carrier all traffic will be + * redirected to the configured backup port. Set the value to 0 to disable + * it. + * + * @IFLA_BRPORT_MRP_RING_OPEN + * + * @IFLA_BRPORT_MRP_IN_OPEN + * + * @IFLA_BRPORT_MCAST_EHT_HOSTS_LIMIT + * The number of per-port EHT hosts limit. The default value is 512. + * Setting to 0 is not allowed. + * + * @IFLA_BRPORT_MCAST_EHT_HOSTS_CNT + * The current number of tracked hosts, read only. + * + * @IFLA_BRPORT_LOCKED + * Controls whether a port will be locked, meaning that hosts behind the + * port will not be able to communicate through the port unless an FDB + * entry with the unit's MAC address is in the FDB. The common use case is + * that hosts are allowed access through authentication with the IEEE 802.1X + * protocol or based on whitelists. By default this flag is off. + * + * Please note that secure 802.1X deployments should always use the + * *BR_BOOLOPT_NO_LL_LEARN* flag, to not permit the bridge to populate its + * FDB based on link-local (EAPOL) traffic received on the port. + * + * @IFLA_BRPORT_MAB + * Controls whether a port will use MAC Authentication Bypass (MAB), a + * technique through which select MAC addresses may be allowed on a locked + * port, without using 802.1X authentication. Packets with an unknown source + * MAC address generates a "locked" FDB entry on the incoming bridge port. + * The common use case is for user space to react to these bridge FDB + * notifications and optionally replace the locked FDB entry with a normal + * one, allowing traffic to pass for whitelisted MAC addresses. + * + * Setting this flag also requires *IFLA_BRPORT_LOCKED* and + * *IFLA_BRPORT_LEARNING*. *IFLA_BRPORT_LOCKED* ensures that unauthorized + * data packets are dropped, and *IFLA_BRPORT_LEARNING* allows the dynamic + * FDB entries installed by user space (as replacements for the locked FDB + * entries) to be refreshed and/or aged out. + * + * @IFLA_BRPORT_MCAST_N_GROUPS + * + * @IFLA_BRPORT_MCAST_MAX_GROUPS + * Sets the maximum number of MDB entries that can be registered for a + * given port. Attempts to register more MDB entries at the port than this + * limit allows will be rejected, whether they are done through netlink + * (e.g. the bridge tool), or IGMP or MLD membership reports. Setting a + * limit of 0 disables the limit. The default value is 0. + * + * @IFLA_BRPORT_NEIGH_VLAN_SUPPRESS + * Controls whether neighbor discovery (arp and nd) proxy and suppression is + * enabled for a given port. By default this flag is off. + * + * Note that this option only takes effect when *IFLA_BRPORT_NEIGH_SUPPRESS* + * is enabled for a given port. + * + * @IFLA_BRPORT_BACKUP_NHID + * The FDB nexthop object ID to attach to packets being redirected to a + * backup port that has VLAN tunnel mapping enabled (via the + * *IFLA_BRPORT_VLAN_TUNNEL* option). Setting a value of 0 (default) has + * the effect of not attaching any ID. + */ enum { IFLA_BRPORT_UNSPEC, IFLA_BRPORT_STATE, /* Spanning tree state */ diff --git a/include/uapi/linux/if_xdp.h b/include/uapi/linux/if_xdp.h index 8d48863472b9..d31698410410 100644 --- a/include/uapi/linux/if_xdp.h +++ b/include/uapi/linux/if_xdp.h @@ -33,7 +33,13 @@ #define XDP_USE_SG (1 << 4) /* Flags for xsk_umem_config flags */ -#define XDP_UMEM_UNALIGNED_CHUNK_FLAG (1 << 0) +#define XDP_UMEM_UNALIGNED_CHUNK_FLAG (1 << 0) + +/* Force checksum calculation in software. Can be used for testing or + * working around potential HW issues. This option causes performance + * degradation and only works in XDP_COPY mode. + */ +#define XDP_UMEM_TX_SW_CSUM (1 << 1) struct sockaddr_xdp { __u16 sxdp_family; @@ -76,6 +82,7 @@ struct xdp_umem_reg { __u32 chunk_size; __u32 headroom; __u32 flags; + __u32 tx_metadata_len; }; struct xdp_statistics { @@ -105,6 +112,41 @@ struct xdp_options { #define XSK_UNALIGNED_BUF_ADDR_MASK \ ((1ULL << XSK_UNALIGNED_BUF_OFFSET_SHIFT) - 1) +/* Request transmit timestamp. Upon completion, put it into tx_timestamp + * field of struct xsk_tx_metadata. + */ +#define XDP_TXMD_FLAGS_TIMESTAMP (1 << 0) + +/* Request transmit checksum offload. Checksum start position and offset + * are communicated via csum_start and csum_offset fields of struct + * xsk_tx_metadata. + */ +#define XDP_TXMD_FLAGS_CHECKSUM (1 << 1) + +/* AF_XDP offloads request. 'request' union member is consumed by the driver + * when the packet is being transmitted. 'completion' union member is + * filled by the driver when the transmit completion arrives. + */ +struct xsk_tx_metadata { + __u64 flags; + + union { + struct { + /* XDP_TXMD_FLAGS_CHECKSUM */ + + /* Offset from desc->addr where checksumming should start. */ + __u16 csum_start; + /* Offset from csum_start where checksum should be stored. */ + __u16 csum_offset; + } request; + + struct { + /* XDP_TXMD_FLAGS_TIMESTAMP */ + __u64 tx_timestamp; + } completion; + }; +}; + /* Rx/Tx descriptor */ struct xdp_desc { __u64 addr; @@ -121,4 +163,7 @@ struct xdp_desc { */ #define XDP_PKT_CONTD (1 << 0) +/* TX packet carries valid metadata. */ +#define XDP_TX_METADATA (1 << 1) + #endif /* _LINUX_IF_XDP_H */ diff --git a/include/uapi/linux/mptcp_pm.h b/include/uapi/linux/mptcp_pm.h index b5d11aece408..50589e5dd6a3 100644 --- a/include/uapi/linux/mptcp_pm.h +++ b/include/uapi/linux/mptcp_pm.h @@ -1,6 +1,6 @@ /* SPDX-License-Identifier: ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) */ /* Do not edit directly, auto-generated from: */ -/* Documentation/netlink/specs/mptcp.yaml */ +/* Documentation/netlink/specs/mptcp_pm.yaml */ /* YNL-GEN uapi header */ #ifndef _UAPI_LINUX_MPTCP_PM_H diff --git a/include/uapi/linux/netdev.h b/include/uapi/linux/netdev.h index 2b37233e00c0..424c5e28f495 100644 --- a/include/uapi/linux/netdev.h +++ b/include/uapi/linux/netdev.h @@ -48,9 +48,23 @@ enum netdev_xdp_act { enum netdev_xdp_rx_metadata { NETDEV_XDP_RX_METADATA_TIMESTAMP = 1, NETDEV_XDP_RX_METADATA_HASH = 2, +}; - /* private: */ - NETDEV_XDP_RX_METADATA_MASK = 3, +/** + * enum netdev_xsk_flags + * @NETDEV_XSK_FLAGS_TX_TIMESTAMP: HW timestamping egress packets is supported + * by the driver. + * @NETDEV_XSK_FLAGS_TX_CHECKSUM: L3 checksum HW offload is supported by the + * driver. + */ +enum netdev_xsk_flags { + NETDEV_XSK_FLAGS_TX_TIMESTAMP = 1, + NETDEV_XSK_FLAGS_TX_CHECKSUM = 2, +}; + +enum netdev_queue_type { + NETDEV_QUEUE_TYPE_RX, + NETDEV_QUEUE_TYPE_TX, }; enum { @@ -59,6 +73,7 @@ enum { NETDEV_A_DEV_XDP_FEATURES, NETDEV_A_DEV_XDP_ZC_MAX_SEGS, NETDEV_A_DEV_XDP_RX_METADATA_FEATURES, + NETDEV_A_DEV_XSK_FEATURES, __NETDEV_A_DEV_MAX, NETDEV_A_DEV_MAX = (__NETDEV_A_DEV_MAX - 1) @@ -95,6 +110,26 @@ enum { }; enum { + NETDEV_A_NAPI_IFINDEX = 1, + NETDEV_A_NAPI_ID, + NETDEV_A_NAPI_IRQ, + NETDEV_A_NAPI_PID, + + __NETDEV_A_NAPI_MAX, + NETDEV_A_NAPI_MAX = (__NETDEV_A_NAPI_MAX - 1) +}; + +enum { + NETDEV_A_QUEUE_ID = 1, + NETDEV_A_QUEUE_IFINDEX, + NETDEV_A_QUEUE_TYPE, + NETDEV_A_QUEUE_NAPI_ID, + + __NETDEV_A_QUEUE_MAX, + NETDEV_A_QUEUE_MAX = (__NETDEV_A_QUEUE_MAX - 1) +}; + +enum { NETDEV_CMD_DEV_GET = 1, NETDEV_CMD_DEV_ADD_NTF, NETDEV_CMD_DEV_DEL_NTF, @@ -104,6 +139,8 @@ enum { NETDEV_CMD_PAGE_POOL_DEL_NTF, NETDEV_CMD_PAGE_POOL_CHANGE_NTF, NETDEV_CMD_PAGE_POOL_STATS_GET, + NETDEV_CMD_QUEUE_GET, + NETDEV_CMD_NAPI_GET, __NETDEV_CMD_MAX, NETDEV_CMD_MAX = (__NETDEV_CMD_MAX - 1) diff --git a/include/uapi/linux/stddef.h b/include/uapi/linux/stddef.h index 5c6c4269f7ef..2ec6f35cda32 100644 --- a/include/uapi/linux/stddef.h +++ b/include/uapi/linux/stddef.h @@ -27,7 +27,7 @@ union { \ struct { MEMBERS } ATTRS; \ struct TAG { MEMBERS } ATTRS NAME; \ - } + } ATTRS #ifdef __cplusplus /* sizeof(struct{}) is 1 in C++, not 0, can't use C version of the macro. */ diff --git a/include/uapi/linux/v4l2-subdev.h b/include/uapi/linux/v4l2-subdev.h index 4a195b68f28f..b383c2fe0cf3 100644 --- a/include/uapi/linux/v4l2-subdev.h +++ b/include/uapi/linux/v4l2-subdev.h @@ -239,7 +239,7 @@ struct v4l2_subdev_routing { * set (which is the default), the 'stream' fields will be forced to 0 by the * kernel. */ - #define V4L2_SUBDEV_CLIENT_CAP_STREAMS (1U << 0) + #define V4L2_SUBDEV_CLIENT_CAP_STREAMS (1ULL << 0) /** * struct v4l2_subdev_client_capability - Capabilities of the client accessing |