13 files changed, 317 insertions, 251 deletions

diff --git a/include/linux/platform_data/cros_ec_commands.h b/include/linux/platform_data/cros_ec_commands.h
index 98415686cbfa..69210881ebac 100644
--- a/include/linux/platform_data/cros_ec_commands.h
+++ b/include/linux/platform_data/cros_ec_commands.h
@@ -556,6 +556,9 @@ enum host_event_code {
 	/* Keyboard recovery combo with hardware reinitialization */
 	EC_HOST_EVENT_KEYBOARD_RECOVERY_HW_REINIT = 30,
 
+	/* WoV */
+	EC_HOST_EVENT_WOV = 31,
+
 	/*
 	 * The high bit of the event mask is not used as a host event code.  If
 	 * it reads back as set, then the entire event mask should be
@@ -1277,8 +1280,6 @@ enum ec_feature_code {
 	 * MOTIONSENSE_CMD_TABLET_MODE_LID_ANGLE.
 	 */
 	EC_FEATURE_REFINED_TABLET_MODE_HYSTERESIS = 37,
-	/* EC supports audio codec. */
-	EC_FEATURE_AUDIO_CODEC = 38,
 	/* The MCU is a System Companion Processor (SCP). */
 	EC_FEATURE_SCP = 39,
 	/* The MCU is an Integrated Sensor Hub */
@@ -4468,92 +4469,246 @@ enum mkbp_cec_event {
 
 /*****************************************************************************/
 
-/* Commands for I2S recording on audio codec. */
+/* Commands for audio codec. */
+#define EC_CMD_EC_CODEC 0x00BC
 
-#define EC_CMD_CODEC_I2S 0x00BC
-#define EC_WOV_I2S_SAMPLE_RATE 48000
+enum ec_codec_subcmd {
+	EC_CODEC_GET_CAPABILITIES = 0x0,
+	EC_CODEC_GET_SHM_ADDR = 0x1,
+	EC_CODEC_SET_SHM_ADDR = 0x2,
+	EC_CODEC_SUBCMD_COUNT,
+};
 
-enum ec_codec_i2s_subcmd {
-	EC_CODEC_SET_SAMPLE_DEPTH = 0x0,
-	EC_CODEC_SET_GAIN = 0x1,
-	EC_CODEC_GET_GAIN = 0x2,
-	EC_CODEC_I2S_ENABLE = 0x3,
-	EC_CODEC_I2S_SET_CONFIG = 0x4,
-	EC_CODEC_I2S_SET_TDM_CONFIG = 0x5,
-	EC_CODEC_I2S_SET_BCLK = 0x6,
-	EC_CODEC_I2S_SUBCMD_COUNT = 0x7,
+enum ec_codec_cap {
+	EC_CODEC_CAP_WOV_AUDIO_SHM = 0,
+	EC_CODEC_CAP_WOV_LANG_SHM = 1,
+	EC_CODEC_CAP_LAST = 32,
 };
 
-enum ec_sample_depth_value {
-	EC_CODEC_SAMPLE_DEPTH_16 = 0,
-	EC_CODEC_SAMPLE_DEPTH_24 = 1,
+enum ec_codec_shm_id {
+	EC_CODEC_SHM_ID_WOV_AUDIO = 0x0,
+	EC_CODEC_SHM_ID_WOV_LANG = 0x1,
+	EC_CODEC_SHM_ID_LAST,
 };
 
-enum ec_i2s_config {
-	EC_DAI_FMT_I2S = 0,
-	EC_DAI_FMT_RIGHT_J = 1,
-	EC_DAI_FMT_LEFT_J = 2,
-	EC_DAI_FMT_PCM_A = 3,
-	EC_DAI_FMT_PCM_B = 4,
-	EC_DAI_FMT_PCM_TDM = 5,
+enum ec_codec_shm_type {
+	EC_CODEC_SHM_TYPE_EC_RAM = 0x0,
+	EC_CODEC_SHM_TYPE_SYSTEM_RAM = 0x1,
 };
 
-/*
- * For subcommand EC_CODEC_GET_GAIN.
- */
-struct __ec_align1 ec_codec_i2s_gain {
+struct __ec_align1 ec_param_ec_codec_get_shm_addr {
+	uint8_t shm_id;
+	uint8_t reserved[3];
+};
+
+struct __ec_align4 ec_param_ec_codec_set_shm_addr {
+	uint64_t phys_addr;
+	uint32_t len;
+	uint8_t shm_id;
+	uint8_t reserved[3];
+};
+
+struct __ec_align4 ec_param_ec_codec {
+	uint8_t cmd; /* enum ec_codec_subcmd */
+	uint8_t reserved[3];
+
+	union {
+		struct ec_param_ec_codec_get_shm_addr
+				get_shm_addr_param;
+		struct ec_param_ec_codec_set_shm_addr
+				set_shm_addr_param;
+	};
+};
+
+struct __ec_align4 ec_response_ec_codec_get_capabilities {
+	uint32_t capabilities;
+};
+
+struct __ec_align4 ec_response_ec_codec_get_shm_addr {
+	uint64_t phys_addr;
+	uint32_t len;
+	uint8_t type;
+	uint8_t reserved[3];
+};
+
+/*****************************************************************************/
+
+/* Commands for DMIC on audio codec. */
+#define EC_CMD_EC_CODEC_DMIC 0x00BD
+
+enum ec_codec_dmic_subcmd {
+	EC_CODEC_DMIC_GET_MAX_GAIN = 0x0,
+	EC_CODEC_DMIC_SET_GAIN_IDX = 0x1,
+	EC_CODEC_DMIC_GET_GAIN_IDX = 0x2,
+	EC_CODEC_DMIC_SUBCMD_COUNT,
+};
+
+enum ec_codec_dmic_channel {
+	EC_CODEC_DMIC_CHANNEL_0 = 0x0,
+	EC_CODEC_DMIC_CHANNEL_1 = 0x1,
+	EC_CODEC_DMIC_CHANNEL_2 = 0x2,
+	EC_CODEC_DMIC_CHANNEL_3 = 0x3,
+	EC_CODEC_DMIC_CHANNEL_4 = 0x4,
+	EC_CODEC_DMIC_CHANNEL_5 = 0x5,
+	EC_CODEC_DMIC_CHANNEL_6 = 0x6,
+	EC_CODEC_DMIC_CHANNEL_7 = 0x7,
+	EC_CODEC_DMIC_CHANNEL_COUNT,
+};
+
+struct __ec_align1 ec_param_ec_codec_dmic_set_gain_idx {
+	uint8_t channel; /* enum ec_codec_dmic_channel */
+	uint8_t gain;
+	uint8_t reserved[2];
+};
+
+struct __ec_align1 ec_param_ec_codec_dmic_get_gain_idx {
+	uint8_t channel; /* enum ec_codec_dmic_channel */
+	uint8_t reserved[3];
+};
+
+struct __ec_align4 ec_param_ec_codec_dmic {
+	uint8_t cmd; /* enum ec_codec_dmic_subcmd */
+	uint8_t reserved[3];
+
+	union {
+		struct ec_param_ec_codec_dmic_set_gain_idx
+				set_gain_idx_param;
+		struct ec_param_ec_codec_dmic_get_gain_idx
+				get_gain_idx_param;
+	};
+};
+
+struct __ec_align1 ec_response_ec_codec_dmic_get_max_gain {
+	uint8_t max_gain;
+};
+
+struct __ec_align1 ec_response_ec_codec_dmic_get_gain_idx {
+	uint8_t gain;
+};
+
+/*****************************************************************************/
+
+/* Commands for I2S RX on audio codec. */
+
+#define EC_CMD_EC_CODEC_I2S_RX 0x00BE
+
+enum ec_codec_i2s_rx_subcmd {
+	EC_CODEC_I2S_RX_ENABLE = 0x0,
+	EC_CODEC_I2S_RX_DISABLE = 0x1,
+	EC_CODEC_I2S_RX_SET_SAMPLE_DEPTH = 0x2,
+	EC_CODEC_I2S_RX_SET_DAIFMT = 0x3,
+	EC_CODEC_I2S_RX_SET_BCLK = 0x4,
+	EC_CODEC_I2S_RX_SUBCMD_COUNT,
+};
+
+enum ec_codec_i2s_rx_sample_depth {
+	EC_CODEC_I2S_RX_SAMPLE_DEPTH_16 = 0x0,
+	EC_CODEC_I2S_RX_SAMPLE_DEPTH_24 = 0x1,
+	EC_CODEC_I2S_RX_SAMPLE_DEPTH_COUNT,
+};
+
+enum ec_codec_i2s_rx_daifmt {
+	EC_CODEC_I2S_RX_DAIFMT_I2S = 0x0,
+	EC_CODEC_I2S_RX_DAIFMT_RIGHT_J = 0x1,
+	EC_CODEC_I2S_RX_DAIFMT_LEFT_J = 0x2,
+	EC_CODEC_I2S_RX_DAIFMT_COUNT,
+};
+
+struct __ec_align1 ec_param_ec_codec_i2s_rx_set_sample_depth {
+	uint8_t depth;
+	uint8_t reserved[3];
+};
+
+struct __ec_align1 ec_param_ec_codec_i2s_rx_set_gain {
 	uint8_t left;
 	uint8_t right;
+	uint8_t reserved[2];
 };
 
-struct __ec_todo_unpacked ec_param_codec_i2s_tdm {
-	int16_t ch0_delay; /* 0 to 496 */
-	int16_t ch1_delay; /* -1 to 496 */
-	uint8_t adjacent_to_ch0;
-	uint8_t adjacent_to_ch1;
+struct __ec_align1 ec_param_ec_codec_i2s_rx_set_daifmt {
+	uint8_t daifmt;
+	uint8_t reserved[3];
 };
 
-struct __ec_todo_packed ec_param_codec_i2s {
-	/* enum ec_codec_i2s_subcmd */
-	uint8_t cmd;
+struct __ec_align4 ec_param_ec_codec_i2s_rx_set_bclk {
+	uint32_t bclk;
+};
+
+struct __ec_align4 ec_param_ec_codec_i2s_rx {
+	uint8_t cmd; /* enum ec_codec_i2s_rx_subcmd */
+	uint8_t reserved[3];
+
 	union {
-		/*
-		 * EC_CODEC_SET_SAMPLE_DEPTH
-		 * Value should be one of ec_sample_depth_value.
-		 */
-		uint8_t depth;
+		struct ec_param_ec_codec_i2s_rx_set_sample_depth
+				set_sample_depth_param;
+		struct ec_param_ec_codec_i2s_rx_set_daifmt
+				set_daifmt_param;
+		struct ec_param_ec_codec_i2s_rx_set_bclk
+				set_bclk_param;
+	};
+};
 
-		/*
-		 * EC_CODEC_SET_GAIN
-		 * Value should be 0~43 for both channels.
-		 */
-		struct ec_codec_i2s_gain gain;
+/*****************************************************************************/
+/* Commands for WoV on audio codec. */
+
+#define EC_CMD_EC_CODEC_WOV 0x00BF
+
+enum ec_codec_wov_subcmd {
+	EC_CODEC_WOV_SET_LANG = 0x0,
+	EC_CODEC_WOV_SET_LANG_SHM = 0x1,
+	EC_CODEC_WOV_GET_LANG = 0x2,
+	EC_CODEC_WOV_ENABLE = 0x3,
+	EC_CODEC_WOV_DISABLE = 0x4,
+	EC_CODEC_WOV_READ_AUDIO = 0x5,
+	EC_CODEC_WOV_READ_AUDIO_SHM = 0x6,
+	EC_CODEC_WOV_SUBCMD_COUNT,
+};
 
-		/*
-		 * EC_CODEC_I2S_ENABLE
-		 * 1 to enable, 0 to disable.
-		 */
-		uint8_t i2s_enable;
+/*
+ * @hash is SHA256 of the whole language model.
+ * @total_len indicates the length of whole language model.
+ * @offset is the cursor from the beginning of the model.
+ * @buf is the packet buffer.
+ * @len denotes how many bytes in the buf.
+ */
+struct __ec_align4 ec_param_ec_codec_wov_set_lang {
+	uint8_t hash[32];
+	uint32_t total_len;
+	uint32_t offset;
+	uint8_t buf[128];
+	uint32_t len;
+};
 
-		/*
-		 * EC_CODEC_I2S_SET_CONFIG
-		 * Value should be one of ec_i2s_config.
-		 */
-		uint8_t i2s_config;
+struct __ec_align4 ec_param_ec_codec_wov_set_lang_shm {
+	uint8_t hash[32];
+	uint32_t total_len;
+};
 
-		/*
-		 * EC_CODEC_I2S_SET_TDM_CONFIG
-		 * Value should be one of ec_i2s_config.
-		 */
-		struct ec_param_codec_i2s_tdm tdm_param;
+struct __ec_align4 ec_param_ec_codec_wov {
+	uint8_t cmd; /* enum ec_codec_wov_subcmd */
+	uint8_t reserved[3];
 
-		/*
-		 * EC_CODEC_I2S_SET_BCLK
-		 */
-		uint32_t bclk;
+	union {
+		struct ec_param_ec_codec_wov_set_lang
+				set_lang_param;
+		struct ec_param_ec_codec_wov_set_lang_shm
+				set_lang_shm_param;
 	};
 };
 
+struct __ec_align4 ec_response_ec_codec_wov_get_lang {
+	uint8_t hash[32];
+};
+
+struct __ec_align4 ec_response_ec_codec_wov_read_audio {
+	uint8_t buf[128];
+	uint32_t len;
+};
+
+struct __ec_align4 ec_response_ec_codec_wov_read_audio_shm {
+	uint32_t offset;
+	uint32_t len;
+};
 
 /*****************************************************************************/
 /* System commands */
diff --git a/include/linux/platform_data/cros_ec_proto.h b/include/linux/platform_data/cros_ec_proto.h
index eab7036cda09..30098a551523 100644
--- a/include/linux/platform_data/cros_ec_proto.h
+++ b/include/linux/platform_data/cros_ec_proto.h
@@ -12,6 +12,7 @@
 #include <linux/mutex.h>
 #include <linux/notifier.h>
 
+#include <linux/mfd/cros_ec.h>
 #include <linux/platform_data/cros_ec_commands.h>
 
 #define CROS_EC_DEV_NAME	"cros_ec"
@@ -115,12 +116,16 @@ struct cros_ec_command {
  *            code.
  * @pkt_xfer: Send packet to EC and get response.
  * @lock: One transaction at a time.
- * @mkbp_event_supported: True if this EC supports the MKBP event protocol.
+ * @mkbp_event_supported: 0 if MKBP not supported. Otherwise its value is
+ *                        the maximum supported version of the MKBP host event
+ *                        command + 1.
  * @host_sleep_v1: True if this EC supports the sleep v1 command.
  * @event_notifier: Interrupt event notifier for transport devices.
  * @event_data: Raw payload transferred with the MKBP event.
  * @event_size: Size in bytes of the event data.
  * @host_event_wake_mask: Mask of host events that cause wake from suspend.
+ * @last_event_time: exact time from the hard irq when we got notified of
+ *     a new event.
  * @ec: The platform_device used by the mfd driver to interface with the
  *      main EC.
  * @pd: The platform_device used by the mfd driver to interface with the
@@ -153,7 +158,7 @@ struct cros_ec_device {
 	int (*pkt_xfer)(struct cros_ec_device *ec,
 			struct cros_ec_command *msg);
 	struct mutex lock;
-	bool mkbp_event_supported;
+	u8 mkbp_event_supported;
 	bool host_sleep_v1;
 	struct blocking_notifier_head event_notifier;
 
@@ -161,6 +166,7 @@ struct cros_ec_device {
 	int event_size;
 	u32 host_event_wake_mask;
 	u32 last_resume_result;
+	ktime_t last_event_time;
 
 	/* The platform devices used by the mfd driver */
 	struct platform_device *ec;
@@ -168,14 +174,6 @@ struct cros_ec_device {
 };
 
 /**
- * struct cros_ec_sensor_platform - ChromeOS EC sensor platform information.
- * @sensor_num: Id of the sensor, as reported by the EC.
- */
-struct cros_ec_sensor_platform {
-	u8 sensor_num;
-};
-
-/**
  * struct cros_ec_platform - ChromeOS EC platform information.
  * @ec_name: Name of EC device (e.g. 'cros-ec', 'cros-pd', ...)
  *           used in /dev/ and sysfs.
@@ -187,133 +185,51 @@ struct cros_ec_platform {
 	u16 cmd_offset;
 };
 
-/**
- * cros_ec_suspend() - Handle a suspend operation for the ChromeOS EC device.
- * @ec_dev: Device to suspend.
- *
- * This can be called by drivers to handle a suspend event.
- *
- * Return: 0 on success or negative error code.
- */
 int cros_ec_suspend(struct cros_ec_device *ec_dev);
 
-/**
- * cros_ec_resume() - Handle a resume operation for the ChromeOS EC device.
- * @ec_dev: Device to resume.
- *
- * This can be called by drivers to handle a resume event.
- *
- * Return: 0 on success or negative error code.
- */
 int cros_ec_resume(struct cros_ec_device *ec_dev);
 
-/**
- * cros_ec_prepare_tx() - Prepare an outgoing message in the output buffer.
- * @ec_dev: Device to register.
- * @msg: Message to write.
- *
- * This is intended to be used by all ChromeOS EC drivers, but at present
- * only SPI uses it. Once LPC uses the same protocol it can start using it.
- * I2C could use it now, with a refactor of the existing code.
- *
- * Return: 0 on success or negative error code.
- */
 int cros_ec_prepare_tx(struct cros_ec_device *ec_dev,
 		       struct cros_ec_command *msg);
 
-/**
- * cros_ec_check_result() - Check ec_msg->result.
- * @ec_dev: EC device.
- * @msg: Message to check.
- *
- * This is used by ChromeOS EC drivers to check the ec_msg->result for
- * errors and to warn about them.
- *
- * Return: 0 on success or negative error code.
- */
 int cros_ec_check_result(struct cros_ec_device *ec_dev,
 			 struct cros_ec_command *msg);
 
-/**
- * cros_ec_cmd_xfer() - Send a command to the ChromeOS EC.
- * @ec_dev: EC device.
- * @msg: Message to write.
- *
- * Call this to send a command to the ChromeOS EC.  This should be used
- * instead of calling the EC's cmd_xfer() callback directly.
- *
- * Return: 0 on success or negative error code.
- */
 int cros_ec_cmd_xfer(struct cros_ec_device *ec_dev,
 		     struct cros_ec_command *msg);
 
-/**
- * cros_ec_cmd_xfer_status() - Send a command to the ChromeOS EC.
- * @ec_dev: EC device.
- * @msg: Message to write.
- *
- * This function is identical to cros_ec_cmd_xfer, except it returns success
- * status only if both the command was transmitted successfully and the EC
- * replied with success status. It's not necessary to check msg->result when
- * using this function.
- *
- * Return: The number of bytes transferred on success or negative error code.
- */
 int cros_ec_cmd_xfer_status(struct cros_ec_device *ec_dev,
 			    struct cros_ec_command *msg);
 
-/**
- * cros_ec_register() - Register a new ChromeOS EC, using the provided info.
- * @ec_dev: Device to register.
- *
- * Before calling this, allocate a pointer to a new device and then fill
- * in all the fields up to the --private-- marker.
- *
- * Return: 0 on success or negative error code.
- */
 int cros_ec_register(struct cros_ec_device *ec_dev);
 
-/**
- * cros_ec_unregister() - Remove a ChromeOS EC.
- * @ec_dev: Device to unregister.
- *
- * Call this to deregister a ChromeOS EC, then clean up any private data.
- *
- * Return: 0 on success or negative error code.
- */
 int cros_ec_unregister(struct cros_ec_device *ec_dev);
 
-/**
- * cros_ec_query_all() -  Query the protocol version supported by the
- *         ChromeOS EC.
- * @ec_dev: Device to register.
- *
- * Return: 0 on success or negative error code.
- */
 int cros_ec_query_all(struct cros_ec_device *ec_dev);
 
-/**
- * cros_ec_get_next_event() - Fetch next event from the ChromeOS EC.
- * @ec_dev: Device to fetch event from.
- * @wake_event: Pointer to a bool set to true upon return if the event might be
- *              treated as a wake event. Ignored if null.
- *
- * Return: negative error code on errors; 0 for no data; or else number of
- * bytes received (i.e., an event was retrieved successfully). Event types are
- * written out to @ec_dev->event_data.event_type on success.
- */
-int cros_ec_get_next_event(struct cros_ec_device *ec_dev, bool *wake_event);
+int cros_ec_get_next_event(struct cros_ec_device *ec_dev,
+			   bool *wake_event,
+			   bool *has_more_events);
+
+u32 cros_ec_get_host_event(struct cros_ec_device *ec_dev);
+
+int cros_ec_check_features(struct cros_ec_dev *ec, int feature);
+
+int cros_ec_get_sensor_count(struct cros_ec_dev *ec);
+
+bool cros_ec_handle_event(struct cros_ec_device *ec_dev);
 
 /**
- * cros_ec_get_host_event() - Return a mask of event set by the ChromeOS EC.
- * @ec_dev: Device to fetch event from.
+ * cros_ec_get_time_ns() - Return time in ns.
  *
- * When MKBP is supported, when the EC raises an interrupt, we collect the
- * events raised and call the functions in the ec notifier. This function
- * is a helper to know which events are raised.
+ * This is the function used to record the time for last_event_time in struct
+ * cros_ec_device during the hard irq.
  *
- * Return: 0 on error or non-zero bitmask of one or more EC_HOST_EVENT_*.
+ * Return: ktime_t format since boot.
  */
-u32 cros_ec_get_host_event(struct cros_ec_device *ec_dev);
+static inline ktime_t cros_ec_get_time_ns(void)
+{
+	return ktime_get_boottime_ns();
+}
 
 #endif /* __LINUX_CROS_EC_PROTO_H */
diff --git a/include/linux/platform_data/cros_ec_sensorhub.h b/include/linux/platform_data/cros_ec_sensorhub.h
new file mode 100644
index 000000000000..bef7ffc7fce1
--- /dev/null
+++ b/include/linux/platform_data/cros_ec_sensorhub.h
@@ -0,0 +1,30 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Chrome OS EC MEMS Sensor Hub driver.
+ *
+ * Copyright 2019 Google LLC
+ */
+
+#ifndef __LINUX_PLATFORM_DATA_CROS_EC_SENSORHUB_H
+#define __LINUX_PLATFORM_DATA_CROS_EC_SENSORHUB_H
+
+#include <linux/platform_data/cros_ec_commands.h>
+
+/**
+ * struct cros_ec_sensor_platform - ChromeOS EC sensor platform information.
+ * @sensor_num: Id of the sensor, as reported by the EC.
+ */
+struct cros_ec_sensor_platform {
+	u8 sensor_num;
+};
+
+/**
+ * struct cros_ec_sensorhub - Sensor Hub device data.
+ *
+ * @ec: Embedded Controller where the hub is located.
+ */
+struct cros_ec_sensorhub {
+	struct cros_ec_dev *ec;
+};
+
+#endif   /* __LINUX_PLATFORM_DATA_CROS_EC_SENSORHUB_H */
diff --git a/include/linux/platform_data/gpio_backlight.h b/include/linux/platform_data/gpio_backlight.h
index 34179d600360..1a8b5b1946fe 100644
--- a/include/linux/platform_data/gpio_backlight.h
+++ b/include/linux/platform_data/gpio_backlight.h
@@ -9,9 +9,6 @@ struct device;
 
 struct gpio_backlight_platform_data {
 	struct device *fbdev;
-	int gpio;
-	int def_value;
-	const char *name;
 };
 
 #endif
diff --git a/include/linux/platform_data/hsmmc-omap.h b/include/linux/platform_data/hsmmc-omap.h
index e79d238ff18f..7124a5f4bf06 100644
--- a/include/linux/platform_data/hsmmc-omap.h
+++ b/include/linux/platform_data/hsmmc-omap.h
@@ -67,9 +67,6 @@ struct omap_hsmmc_platform_data {
 	/* string specifying a particular variant of hardware */
 	char *version;
 
-	/* if we have special card, init it using this callback */
-	void (*init_card)(struct mmc_card *card);
-
 	const char *name;
 	u32 ocr_mask;
 };
diff --git a/include/linux/platform_data/i2c-pxa.h b/include/linux/platform_data/i2c-pxa.h
index cb290092599c..6a9b28399b39 100644
--- a/include/linux/platform_data/i2c-pxa.h
+++ b/include/linux/platform_data/i2c-pxa.h
@@ -55,11 +55,7 @@
  */
 #define I2C_ISR_INIT	0x7FF  /* status register init */
 
-struct i2c_slave_client;
-
 struct i2c_pxa_platform_data {
-	unsigned int		slave_addr;
-	struct i2c_slave_client	*slave;
 	unsigned int		class;
 	unsigned int		use_pio :1;
 	unsigned int		fast_mode :1;
diff --git a/include/linux/platform_data/intel-spi.h b/include/linux/platform_data/intel-spi.h
index ebb4f332588b..7f53a5c6f35e 100644
--- a/include/linux/platform_data/intel-spi.h
+++ b/include/linux/platform_data/intel-spi.h
@@ -13,6 +13,7 @@ enum intel_spi_type {
 	INTEL_SPI_BYT = 1,
 	INTEL_SPI_LPT,
 	INTEL_SPI_BXT,
+	INTEL_SPI_CNL,
 };
 
 /**
diff --git a/include/linux/platform_data/pixcir_i2c_ts.h b/include/linux/platform_data/pixcir_i2c_ts.h
deleted file mode 100644
index 4ab3cd6f1cc2..000000000000
--- a/include/linux/platform_data/pixcir_i2c_ts.h
+++ /dev/null
@@ -1,64 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-#ifndef	_PIXCIR_I2C_TS_H
-#define	_PIXCIR_I2C_TS_H
-
-/*
- * Register map
- */
-#define PIXCIR_REG_POWER_MODE	51
-#define PIXCIR_REG_INT_MODE	52
-
-/*
- * Power modes:
- * active: max scan speed
- * idle: lower scan speed with automatic transition to active on touch
- * halt: datasheet says sleep but this is more like halt as the chip
- *       clocks are cut and it can only be brought out of this mode
- *	 using the RESET pin.
- */
-enum pixcir_power_mode {
-	PIXCIR_POWER_ACTIVE,
-	PIXCIR_POWER_IDLE,
-	PIXCIR_POWER_HALT,
-};
-
-#define PIXCIR_POWER_MODE_MASK	0x03
-#define PIXCIR_POWER_ALLOW_IDLE (1UL << 2)
-
-/*
- * Interrupt modes:
- * periodical: interrupt is asserted periodicaly
- * diff coordinates: interrupt is asserted when coordinates change
- * level on touch: interrupt level asserted during touch
- * pulse on touch: interrupt pulse asserted druing touch
- *
- */
-enum pixcir_int_mode {
-	PIXCIR_INT_PERIODICAL,
-	PIXCIR_INT_DIFF_COORD,
-	PIXCIR_INT_LEVEL_TOUCH,
-	PIXCIR_INT_PULSE_TOUCH,
-};
-
-#define PIXCIR_INT_MODE_MASK	0x03
-#define PIXCIR_INT_ENABLE	(1UL << 3)
-#define PIXCIR_INT_POL_HIGH	(1UL << 2)
-
-/**
- * struct pixcir_irc_chip_data - chip related data
- * @max_fingers:	Max number of fingers reported simultaneously by h/w
- * @has_hw_ids:		Hardware supports finger tracking IDs
- *
- */
-struct pixcir_i2c_chip_data {
-	u8 max_fingers;
-	bool has_hw_ids;
-};
-
-struct pixcir_ts_platform_data {
-	int x_max;
-	int y_max;
-	struct pixcir_i2c_chip_data chip;
-};
-
-#endif
diff --git a/include/linux/platform_data/spi-mt65xx.h b/include/linux/platform_data/spi-mt65xx.h
index f0e6d6483e62..65fd5ffd257c 100644
--- a/include/linux/platform_data/spi-mt65xx.h
+++ b/include/linux/platform_data/spi-mt65xx.h
@@ -11,7 +11,6 @@
 
 /* Board specific platform_data */
 struct mtk_chip_config {
-	u32 cs_pol;
 	u32 sample_sel;
 };
 #endif
diff --git a/include/linux/platform_data/st_sensors_pdata.h b/include/linux/platform_data/st_sensors_pdata.h
index 30929c22227d..e40b28ca892e 100644
--- a/include/linux/platform_data/st_sensors_pdata.h
+++ b/include/linux/platform_data/st_sensors_pdata.h
@@ -18,12 +18,14 @@
  * @open_drain: set the interrupt line to be open drain if possible.
  * @spi_3wire: enable spi-3wire mode.
  * @pullups: enable/disable i2c controller pullup resistors.
+ * @wakeup_source: enable/disable device as wakeup generator.
  */
 struct st_sensors_platform_data {
 	u8 drdy_int_pin;
 	bool open_drain;
 	bool spi_3wire;
 	bool pullups;
+	bool wakeup_source;
 };
 
 #endif /* ST_SENSORS_PDATA_H */
diff --git a/include/linux/platform_data/ti-prm.h b/include/linux/platform_data/ti-prm.h
new file mode 100644
index 000000000000..28154c3226c2
--- /dev/null
+++ b/include/linux/platform_data/ti-prm.h
@@ -0,0 +1,21 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * TI PRM (Power & Reset Manager) platform data
+ *
+ * Copyright (C) 2019 Texas Instruments, Inc.
+ *
+ * Tero Kristo <t-kristo@ti.com>
+ */
+
+#ifndef _LINUX_PLATFORM_DATA_TI_PRM_H
+#define _LINUX_PLATFORM_DATA_TI_PRM_H
+
+struct clockdomain;
+
+struct ti_prm_platform_data {
+	void (*clkdm_deny_idle)(struct clockdomain *clkdm);
+	void (*clkdm_allow_idle)(struct clockdomain *clkdm);
+	struct clockdomain * (*clkdm_lookup)(const char *name);
+};
+
+#endif /* _LINUX_PLATFORM_DATA_TI_PRM_H */
diff --git a/include/linux/platform_data/ti-sysc.h b/include/linux/platform_data/ti-sysc.h
index b5b7a3423ca8..0b9380475144 100644
--- a/include/linux/platform_data/ti-sysc.h
+++ b/include/linux/platform_data/ti-sysc.h
@@ -49,6 +49,7 @@ struct sysc_regbits {
 	s8 emufree_shift;
 };
 
+#define SYSC_MODULE_QUIRK_AESS		BIT(19)
 #define SYSC_MODULE_QUIRK_SGX		BIT(18)
 #define SYSC_MODULE_QUIRK_HDQ1W		BIT(17)
 #define SYSC_MODULE_QUIRK_I2C		BIT(16)
diff --git a/include/linux/platform_data/wilco-ec.h b/include/linux/platform_data/wilco-ec.h
index ad03b586a095..afede15a95bf 100644
--- a/include/linux/platform_data/wilco-ec.h
+++ b/include/linux/platform_data/wilco-ec.h
@@ -29,6 +29,7 @@
  * @data_size: Size of the data buffer used for EC communication.
  * @debugfs_pdev: The child platform_device used by the debugfs sub-driver.
  * @rtc_pdev: The child platform_device used by the RTC sub-driver.
+ * @charger_pdev: Child platform_device used by the charger config sub-driver.
  * @telem_pdev: The child platform_device used by the telemetry sub-driver.
  */
 struct wilco_ec_device {
@@ -41,6 +42,7 @@ struct wilco_ec_device {
 	size_t data_size;
 	struct platform_device *debugfs_pdev;
 	struct platform_device *rtc_pdev;
+	struct platform_device *charger_pdev;
 	struct platform_device *telem_pdev;
 };
 
@@ -120,6 +122,19 @@ struct wilco_ec_message {
  */
 int wilco_ec_mailbox(struct wilco_ec_device *ec, struct wilco_ec_message *msg);
 
+/**
+ * wilco_keyboard_leds_init() - Set up the keyboard backlight LEDs.
+ * @ec: EC device to query.
+ *
+ * After this call, the keyboard backlight will be exposed through a an LED
+ * device at /sys/class/leds.
+ *
+ * This may sleep because it uses wilco_ec_mailbox().
+ *
+ * Return: 0 on success, negative error code on failure.
+ */
+int wilco_keyboard_leds_init(struct wilco_ec_device *ec);
+
 /*
  * A Property is typically a data item that is stored to NVRAM
  * by the EC. Each of these data items has an index associated