diff options
Diffstat (limited to 'include/linux/platform_data')
26 files changed, 543 insertions, 266 deletions
diff --git a/include/linux/platform_data/at24.h b/include/linux/platform_data/at24.h new file mode 100644 index 000000000000..c42aa89d34ee --- /dev/null +++ b/include/linux/platform_data/at24.h @@ -0,0 +1,55 @@ +/* + * at24.h - platform_data for the at24 (generic eeprom) driver + * (C) Copyright 2008 by Pengutronix + * (C) Copyright 2012 by Wolfram Sang + * same license as the driver + */ + +#ifndef _LINUX_AT24_H +#define _LINUX_AT24_H + +#include <linux/types.h> +#include <linux/memory.h> + +/** + * struct at24_platform_data - data to set up at24 (generic eeprom) driver + * @byte_len: size of eeprom in byte + * @page_size: number of byte which can be written in one go + * @flags: tunable options, check AT24_FLAG_* defines + * @setup: an optional callback invoked after eeprom is probed; enables kernel + code to access eeprom via memory_accessor, see example + * @context: optional parameter passed to setup() + * + * If you set up a custom eeprom type, please double-check the parameters. + * Especially page_size needs extra care, as you risk data loss if your value + * is bigger than what the chip actually supports! + * + * An example in pseudo code for a setup() callback: + * + * void get_mac_addr(struct memory_accessor *mem_acc, void *context) + * { + * u8 *mac_addr = ethernet_pdata->mac_addr; + * off_t offset = context; + * + * // Read MAC addr from EEPROM + * if (mem_acc->read(mem_acc, mac_addr, offset, ETH_ALEN) == ETH_ALEN) + * pr_info("Read MAC addr from EEPROM: %pM\n", mac_addr); + * } + * + * This function pointer and context can now be set up in at24_platform_data. + */ + +struct at24_platform_data { + u32 byte_len; /* size (sum of all addr) */ + u16 page_size; /* for writes */ + u8 flags; +#define AT24_FLAG_ADDR16 0x80 /* address pointer is 16 bit */ +#define AT24_FLAG_READONLY 0x40 /* sysfs-entry will be read-only */ +#define AT24_FLAG_IRUGO 0x20 /* sysfs-entry will be world-readable */ +#define AT24_FLAG_TAKE8ADDR 0x10 /* take always 8 addresses (24c00) */ + + void (*setup)(struct memory_accessor *, void *context); + void *context; +}; + +#endif /* _LINUX_AT24_H */ diff --git a/include/linux/platform_data/atmel.h b/include/linux/platform_data/atmel.h index 6a293b7fff3b..cea9f70133c5 100644 --- a/include/linux/platform_data/atmel.h +++ b/include/linux/platform_data/atmel.h @@ -71,6 +71,10 @@ struct atmel_nand_data { u8 on_flash_bbt; /* bbt on flash */ struct mtd_partition *parts; unsigned int num_parts; + bool has_dma; /* support dma transfer */ + + /* default is false, only for at32ap7000 chip is true */ + bool need_reset_workaround; }; /* Serial */ diff --git a/include/linux/platform_data/clk-nomadik.h b/include/linux/platform_data/clk-nomadik.h deleted file mode 100644 index 5713c87b2477..000000000000 --- a/include/linux/platform_data/clk-nomadik.h +++ /dev/null @@ -1,2 +0,0 @@ -/* Minimal platform data header */ -void nomadik_clk_init(void); diff --git a/include/linux/platform_data/clk-ux500.h b/include/linux/platform_data/clk-ux500.h index 9d98f3aaa16c..97baf831e071 100644 --- a/include/linux/platform_data/clk-ux500.h +++ b/include/linux/platform_data/clk-ux500.h @@ -10,6 +10,9 @@ #ifndef __CLK_UX500_H #define __CLK_UX500_H +void u8500_of_clk_init(u32 clkrst1_base, u32 clkrst2_base, u32 clkrst3_base, + u32 clkrst5_base, u32 clkrst6_base); + void u8500_clk_init(u32 clkrst1_base, u32 clkrst2_base, u32 clkrst3_base, u32 clkrst5_base, u32 clkrst6_base); void u9540_clk_init(u32 clkrst1_base, u32 clkrst2_base, u32 clkrst3_base, diff --git a/include/linux/platform_data/davinci_asp.h b/include/linux/platform_data/davinci_asp.h index 8db5ae03b6e3..689a856b86f9 100644 --- a/include/linux/platform_data/davinci_asp.h +++ b/include/linux/platform_data/davinci_asp.h @@ -84,6 +84,8 @@ struct snd_platform_data { u8 version; u8 txnumevt; u8 rxnumevt; + int tx_dma_channel; + int rx_dma_channel; }; enum { diff --git a/include/linux/platform_data/dma-rcar-hpbdma.h b/include/linux/platform_data/dma-rcar-hpbdma.h new file mode 100644 index 000000000000..648b8ea61a22 --- /dev/null +++ b/include/linux/platform_data/dma-rcar-hpbdma.h @@ -0,0 +1,103 @@ +/* + * Copyright (C) 2011-2013 Renesas Electronics Corporation + * Copyright (C) 2013 Cogent Embedded, Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 + * as published by the Free Software Foundation. + */ + +#ifndef __DMA_RCAR_HPBDMA_H +#define __DMA_RCAR_HPBDMA_H + +#include <linux/bitops.h> +#include <linux/types.h> + +/* Transmit sizes and respective register values */ +enum { + XMIT_SZ_8BIT = 0, + XMIT_SZ_16BIT = 1, + XMIT_SZ_32BIT = 2, + XMIT_SZ_MAX +}; + +/* DMA control register (DCR) bits */ +#define HPB_DMAE_DCR_DTAMD (1u << 26) +#define HPB_DMAE_DCR_DTAC (1u << 25) +#define HPB_DMAE_DCR_DTAU (1u << 24) +#define HPB_DMAE_DCR_DTAU1 (1u << 23) +#define HPB_DMAE_DCR_SWMD (1u << 22) +#define HPB_DMAE_DCR_BTMD (1u << 21) +#define HPB_DMAE_DCR_PKMD (1u << 20) +#define HPB_DMAE_DCR_CT (1u << 18) +#define HPB_DMAE_DCR_ACMD (1u << 17) +#define HPB_DMAE_DCR_DIP (1u << 16) +#define HPB_DMAE_DCR_SMDL (1u << 13) +#define HPB_DMAE_DCR_SPDAM (1u << 12) +#define HPB_DMAE_DCR_SDRMD_MASK (3u << 10) +#define HPB_DMAE_DCR_SDRMD_MOD (0u << 10) +#define HPB_DMAE_DCR_SDRMD_AUTO (1u << 10) +#define HPB_DMAE_DCR_SDRMD_TIMER (2u << 10) +#define HPB_DMAE_DCR_SPDS_MASK (3u << 8) +#define HPB_DMAE_DCR_SPDS_8BIT (0u << 8) +#define HPB_DMAE_DCR_SPDS_16BIT (1u << 8) +#define HPB_DMAE_DCR_SPDS_32BIT (2u << 8) +#define HPB_DMAE_DCR_DMDL (1u << 5) +#define HPB_DMAE_DCR_DPDAM (1u << 4) +#define HPB_DMAE_DCR_DDRMD_MASK (3u << 2) +#define HPB_DMAE_DCR_DDRMD_MOD (0u << 2) +#define HPB_DMAE_DCR_DDRMD_AUTO (1u << 2) +#define HPB_DMAE_DCR_DDRMD_TIMER (2u << 2) +#define HPB_DMAE_DCR_DPDS_MASK (3u << 0) +#define HPB_DMAE_DCR_DPDS_8BIT (0u << 0) +#define HPB_DMAE_DCR_DPDS_16BIT (1u << 0) +#define HPB_DMAE_DCR_DPDS_32BIT (2u << 0) + +/* Asynchronous reset register (ASYNCRSTR) bits */ +#define HPB_DMAE_ASYNCRSTR_ASRST41 BIT(10) +#define HPB_DMAE_ASYNCRSTR_ASRST40 BIT(9) +#define HPB_DMAE_ASYNCRSTR_ASRST39 BIT(8) +#define HPB_DMAE_ASYNCRSTR_ASRST27 BIT(7) +#define HPB_DMAE_ASYNCRSTR_ASRST26 BIT(6) +#define HPB_DMAE_ASYNCRSTR_ASRST25 BIT(5) +#define HPB_DMAE_ASYNCRSTR_ASRST24 BIT(4) +#define HPB_DMAE_ASYNCRSTR_ASRST23 BIT(3) +#define HPB_DMAE_ASYNCRSTR_ASRST22 BIT(2) +#define HPB_DMAE_ASYNCRSTR_ASRST21 BIT(1) +#define HPB_DMAE_ASYNCRSTR_ASRST20 BIT(0) + +struct hpb_dmae_slave_config { + unsigned int id; + dma_addr_t addr; + u32 dcr; + u32 port; + u32 rstr; + u32 mdr; + u32 mdm; + u32 flags; +#define HPB_DMAE_SET_ASYNC_RESET BIT(0) +#define HPB_DMAE_SET_ASYNC_MODE BIT(1) + u32 dma_ch; +}; + +#define HPB_DMAE_CHANNEL(_irq, _s_id) \ +{ \ + .ch_irq = _irq, \ + .s_id = _s_id, \ +} + +struct hpb_dmae_channel { + unsigned int ch_irq; + unsigned int s_id; +}; + +struct hpb_dmae_pdata { + const struct hpb_dmae_slave_config *slaves; + int num_slaves; + const struct hpb_dmae_channel *channels; + int num_channels; + const unsigned int ts_shift[XMIT_SZ_MAX]; + int num_hw_channels; +}; + +#endif diff --git a/include/linux/platform_data/dma-s3c24xx.h b/include/linux/platform_data/dma-s3c24xx.h new file mode 100644 index 000000000000..89ba1b0c90e4 --- /dev/null +++ b/include/linux/platform_data/dma-s3c24xx.h @@ -0,0 +1,46 @@ +/* + * S3C24XX DMA handling + * + * Copyright (c) 2013 Heiko Stuebner <heiko@sntech.de> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the Free + * Software Foundation; either version 2 of the License, or (at your option) + * any later version. + */ + +/* Helper to encode the source selection constraints for early s3c socs. */ +#define S3C24XX_DMA_CHANREQ(src, chan) ((BIT(3) | src) << chan * 4) + +enum s3c24xx_dma_bus { + S3C24XX_DMA_APB, + S3C24XX_DMA_AHB, +}; + +/** + * @bus: on which bus does the peripheral reside - AHB or APB. + * @handshake: is a handshake with the peripheral necessary + * @chansel: channel selection information, depending on variant; reqsel for + * s3c2443 and later and channel-selection map for earlier SoCs + * see CHANSEL doc in s3c2443-dma.c + */ +struct s3c24xx_dma_channel { + enum s3c24xx_dma_bus bus; + bool handshake; + u16 chansel; +}; + +/** + * struct s3c24xx_dma_platdata - platform specific settings + * @num_phy_channels: number of physical channels + * @channels: array of virtual channel descriptions + * @num_channels: number of virtual channels + */ +struct s3c24xx_dma_platdata { + int num_phy_channels; + struct s3c24xx_dma_channel *channels; + int num_channels; +}; + +struct dma_chan; +bool s3c24xx_dma_filter(struct dma_chan *chan, void *param); diff --git a/include/linux/platform_data/edma.h b/include/linux/platform_data/edma.h index 57300fd7cc03..f50821cb64be 100644 --- a/include/linux/platform_data/edma.h +++ b/include/linux/platform_data/edma.h @@ -67,10 +67,10 @@ struct edmacc_param { #define ITCCHEN BIT(23) /*ch_status paramater of callback function possible values*/ -#define DMA_COMPLETE 1 -#define DMA_CC_ERROR 2 -#define DMA_TC1_ERROR 3 -#define DMA_TC2_ERROR 4 +#define EDMA_DMA_COMPLETE 1 +#define EDMA_DMA_CC_ERROR 2 +#define EDMA_DMA_TC1_ERROR 3 +#define EDMA_DMA_TC2_ERROR 4 enum address_mode { INCR = 0, @@ -180,4 +180,6 @@ struct edma_soc_info { const s16 (*xbar_chans)[2]; }; +int edma_trigger_channel(unsigned); + #endif diff --git a/include/linux/platform_data/exynos_thermal.h b/include/linux/platform_data/exynos_thermal.h deleted file mode 100644 index da7e6274b175..000000000000 --- a/include/linux/platform_data/exynos_thermal.h +++ /dev/null @@ -1,119 +0,0 @@ -/* - * exynos_thermal.h - Samsung EXYNOS TMU (Thermal Management Unit) - * - * Copyright (C) 2011 Samsung Electronics - * Donggeun Kim <dg77.kim@samsung.com> - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA - */ - -#ifndef _LINUX_EXYNOS_THERMAL_H -#define _LINUX_EXYNOS_THERMAL_H -#include <linux/cpu_cooling.h> - -enum calibration_type { - TYPE_ONE_POINT_TRIMMING, - TYPE_TWO_POINT_TRIMMING, - TYPE_NONE, -}; - -enum soc_type { - SOC_ARCH_EXYNOS4210 = 1, - SOC_ARCH_EXYNOS, -}; -/** - * struct freq_clip_table - * @freq_clip_max: maximum frequency allowed for this cooling state. - * @temp_level: Temperature level at which the temperature clipping will - * happen. - * @mask_val: cpumask of the allowed cpu's where the clipping will take place. - * - * This structure is required to be filled and passed to the - * cpufreq_cooling_unregister function. - */ -struct freq_clip_table { - unsigned int freq_clip_max; - unsigned int temp_level; - const struct cpumask *mask_val; -}; - -/** - * struct exynos_tmu_platform_data - * @threshold: basic temperature for generating interrupt - * 25 <= threshold <= 125 [unit: degree Celsius] - * @threshold_falling: differntial value for setting threshold - * of temperature falling interrupt. - * @trigger_levels: array for each interrupt levels - * [unit: degree Celsius] - * 0: temperature for trigger_level0 interrupt - * condition for trigger_level0 interrupt: - * current temperature > threshold + trigger_levels[0] - * 1: temperature for trigger_level1 interrupt - * condition for trigger_level1 interrupt: - * current temperature > threshold + trigger_levels[1] - * 2: temperature for trigger_level2 interrupt - * condition for trigger_level2 interrupt: - * current temperature > threshold + trigger_levels[2] - * 3: temperature for trigger_level3 interrupt - * condition for trigger_level3 interrupt: - * current temperature > threshold + trigger_levels[3] - * @trigger_level0_en: - * 1 = enable trigger_level0 interrupt, - * 0 = disable trigger_level0 interrupt - * @trigger_level1_en: - * 1 = enable trigger_level1 interrupt, - * 0 = disable trigger_level1 interrupt - * @trigger_level2_en: - * 1 = enable trigger_level2 interrupt, - * 0 = disable trigger_level2 interrupt - * @trigger_level3_en: - * 1 = enable trigger_level3 interrupt, - * 0 = disable trigger_level3 interrupt - * @gain: gain of amplifier in the positive-TC generator block - * 0 <= gain <= 15 - * @reference_voltage: reference voltage of amplifier - * in the positive-TC generator block - * 0 <= reference_voltage <= 31 - * @noise_cancel_mode: noise cancellation mode - * 000, 100, 101, 110 and 111 can be different modes - * @type: determines the type of SOC - * @efuse_value: platform defined fuse value - * @cal_type: calibration type for temperature - * @freq_clip_table: Table representing frequency reduction percentage. - * @freq_tab_count: Count of the above table as frequency reduction may - * applicable to only some of the trigger levels. - * - * This structure is required for configuration of exynos_tmu driver. - */ -struct exynos_tmu_platform_data { - u8 threshold; - u8 threshold_falling; - u8 trigger_levels[4]; - bool trigger_level0_en; - bool trigger_level1_en; - bool trigger_level2_en; - bool trigger_level3_en; - - u8 gain; - u8 reference_voltage; - u8 noise_cancel_mode; - u32 efuse_value; - - enum calibration_type cal_type; - enum soc_type type; - struct freq_clip_table freq_tab[4]; - unsigned int freq_tab_count; -}; -#endif /* _LINUX_EXYNOS_THERMAL_H */ diff --git a/include/linux/platform_data/gpio-davinci.h b/include/linux/platform_data/gpio-davinci.h new file mode 100644 index 000000000000..6efd20264585 --- /dev/null +++ b/include/linux/platform_data/gpio-davinci.h @@ -0,0 +1,60 @@ +/* + * DaVinci GPIO Platform Related Defines + * + * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation version 2. + * + * This program is distributed "as is" WITHOUT ANY WARRANTY of any + * kind, whether express or implied; without even the implied warranty + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#ifndef __DAVINCI_GPIO_PLATFORM_H +#define __DAVINCI_GPIO_PLATFORM_H + +#include <linux/io.h> +#include <linux/spinlock.h> + +#include <asm-generic/gpio.h> + +enum davinci_gpio_type { + GPIO_TYPE_TNETV107X = 0, +}; + +struct davinci_gpio_platform_data { + u32 ngpio; + u32 gpio_unbanked; + u32 intc_irq_num; +}; + + +struct davinci_gpio_controller { + struct gpio_chip chip; + int irq_base; + /* Serialize access to GPIO registers */ + spinlock_t lock; + void __iomem *regs; + void __iomem *set_data; + void __iomem *clr_data; + void __iomem *in_data; + int gpio_unbanked; + unsigned gpio_irq; +}; + +/* + * basic gpio routines + */ +#define GPIO(X) (X) /* 0 <= X <= (DAVINCI_N_GPIO - 1) */ + +/* Convert GPIO signal to GPIO pin number */ +#define GPIO_TO_PIN(bank, gpio) (16 * (bank) + (gpio)) + +static inline u32 __gpio_mask(unsigned gpio) +{ + return 1 << (gpio % 32); +} +#endif diff --git a/include/linux/platform_data/leds-lp55xx.h b/include/linux/platform_data/leds-lp55xx.h index 202e290faea8..624ff9edad6f 100644 --- a/include/linux/platform_data/leds-lp55xx.h +++ b/include/linux/platform_data/leds-lp55xx.h @@ -22,6 +22,7 @@ struct lp55xx_led_config { const char *name; + const char *default_trigger; u8 chan_nr; u8 led_current; /* mA x10, 0 if led is not connected */ u8 max_current; @@ -36,6 +37,13 @@ struct lp55xx_predef_pattern { u8 size_b; }; +enum lp8501_pwr_sel { + LP8501_ALL_VDD, /* D1~9 are connected to VDD */ + LP8501_6VDD_3VOUT, /* D1~6 with VDD, D7~9 with VOUT */ + LP8501_3VDD_6VOUT, /* D1~6 with VOUT, D7~9 with VDD */ + LP8501_ALL_VOUT, /* D1~9 are connected to VOUT */ +}; + /* * struct lp55xx_platform_data * @led_config : Configurable led class device @@ -59,14 +67,15 @@ struct lp55xx_platform_data { /* Clock configuration */ u8 clock_mode; - /* Platform specific functions */ - int (*setup_resources)(void); - void (*release_resources)(void); - void (*enable)(bool state); + /* optional enable GPIO */ + int enable_gpio; /* Predefined pattern data */ struct lp55xx_predef_pattern *patterns; unsigned int num_patterns; + + /* LP8501 specific */ + enum lp8501_pwr_sel pwr_sel; }; #endif /* _LEDS_LP55XX_H */ diff --git a/include/linux/platform_data/leds-pca9633.h b/include/linux/platform_data/leds-pca963x.h index c5bf29b6fa7f..e731f0036329 100644 --- a/include/linux/platform_data/leds-pca9633.h +++ b/include/linux/platform_data/leds-pca963x.h @@ -1,7 +1,8 @@ /* - * PCA9633 LED chip driver. + * PCA963X LED chip driver. * * Copyright 2012 bct electronic GmbH + * Copyright 2013 Qtechnology A/S * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License @@ -18,18 +19,24 @@ * 02110-1301 USA */ -#ifndef __LINUX_PCA9633_H -#define __LINUX_PCA9633_H +#ifndef __LINUX_PCA963X_H +#define __LINUX_PCA963X_H #include <linux/leds.h> -enum pca9633_outdrv { - PCA9633_OPEN_DRAIN, - PCA9633_TOTEM_POLE, /* aka push-pull */ +enum pca963x_outdrv { + PCA963X_OPEN_DRAIN, + PCA963X_TOTEM_POLE, /* aka push-pull */ }; -struct pca9633_platform_data { +enum pca963x_blink_type { + PCA963X_SW_BLINK, + PCA963X_HW_BLINK, +}; + +struct pca963x_platform_data { struct led_platform_data leds; - enum pca9633_outdrv outdrv; + enum pca963x_outdrv outdrv; + enum pca963x_blink_type blink_type; }; -#endif /* __LINUX_PCA9633_H*/ +#endif /* __LINUX_PCA963X_H*/ diff --git a/include/linux/platform_data/leds-pca9685.h b/include/linux/platform_data/leds-pca9685.h new file mode 100644 index 000000000000..778e9e4249cc --- /dev/null +++ b/include/linux/platform_data/leds-pca9685.h @@ -0,0 +1,35 @@ +/* + * Copyright 2013 Maximilian Güntner <maximilian.guentner@gmail.com> + * + * This file is subject to the terms and conditions of version 2 of + * the GNU General Public License. See the file COPYING in the main + * directory of this archive for more details. + * + * Based on leds-pca963x.h by Peter Meerwald <p.meerwald@bct-electronic.com> + * + * LED driver for the NXP PCA9685 PWM chip + * + */ + +#ifndef __LINUX_PCA9685_H +#define __LINUX_PCA9685_H + +#include <linux/leds.h> + +enum pca9685_outdrv { + PCA9685_OPEN_DRAIN, + PCA9685_TOTEM_POLE, +}; + +enum pca9685_inverted { + PCA9685_NOT_INVERTED, + PCA9685_INVERTED, +}; + +struct pca9685_platform_data { + struct led_platform_data leds; + enum pca9685_outdrv outdrv; + enum pca9685_inverted inverted; +}; + +#endif /* __LINUX_PCA9685_H */ diff --git a/include/linux/platform_data/lm3630_bl.h b/include/linux/platform_data/lm3630_bl.h deleted file mode 100644 index 9176dd3f2d63..000000000000 --- a/include/linux/platform_data/lm3630_bl.h +++ /dev/null @@ -1,57 +0,0 @@ -/* -* Simple driver for Texas Instruments LM3630 LED Flash driver chip -* Copyright (C) 2012 Texas Instruments -* -* This program is free software; you can redistribute it and/or modify -* it under the terms of the GNU General Public License version 2 as -* published by the Free Software Foundation. -* -*/ - -#ifndef __LINUX_LM3630_H -#define __LINUX_LM3630_H - -#define LM3630_NAME "lm3630_bl" - -enum lm3630_pwm_ctrl { - PWM_CTRL_DISABLE = 0, - PWM_CTRL_BANK_A, - PWM_CTRL_BANK_B, - PWM_CTRL_BANK_ALL, -}; - -enum lm3630_pwm_active { - PWM_ACTIVE_HIGH = 0, - PWM_ACTIVE_LOW, -}; - -enum lm3630_bank_a_ctrl { - BANK_A_CTRL_DISABLE = 0x0, - BANK_A_CTRL_LED1 = 0x4, - BANK_A_CTRL_LED2 = 0x1, - BANK_A_CTRL_ALL = 0x5, -}; - -enum lm3630_bank_b_ctrl { - BANK_B_CTRL_DISABLE = 0, - BANK_B_CTRL_LED2, -}; - -struct lm3630_platform_data { - - /* maximum brightness */ - int max_brt_led1; - int max_brt_led2; - - /* initial on brightness */ - int init_brt_led1; - int init_brt_led2; - enum lm3630_pwm_ctrl pwm_ctrl; - enum lm3630_pwm_active pwm_active; - enum lm3630_bank_a_ctrl bank_a_ctrl; - enum lm3630_bank_b_ctrl bank_b_ctrl; - unsigned int pwm_period; - void (*pwm_set_intensity) (int brightness, int max_brightness); -}; - -#endif /* __LINUX_LM3630_H */ diff --git a/include/linux/platform_data/lm3630a_bl.h b/include/linux/platform_data/lm3630a_bl.h new file mode 100644 index 000000000000..7538e38e270b --- /dev/null +++ b/include/linux/platform_data/lm3630a_bl.h @@ -0,0 +1,65 @@ +/* +* Simple driver for Texas Instruments LM3630A LED Flash driver chip +* Copyright (C) 2012 Texas Instruments +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License version 2 as +* published by the Free Software Foundation. +* +*/ + +#ifndef __LINUX_LM3630A_H +#define __LINUX_LM3630A_H + +#define LM3630A_NAME "lm3630a_bl" + +enum lm3630a_pwm_ctrl { + LM3630A_PWM_DISABLE = 0x00, + LM3630A_PWM_BANK_A, + LM3630A_PWM_BANK_B, + LM3630A_PWM_BANK_ALL, + LM3630A_PWM_BANK_A_ACT_LOW = 0x05, + LM3630A_PWM_BANK_B_ACT_LOW, + LM3630A_PWM_BANK_ALL_ACT_LOW, +}; + +enum lm3630a_leda_ctrl { + LM3630A_LEDA_DISABLE = 0x00, + LM3630A_LEDA_ENABLE = 0x04, + LM3630A_LEDA_ENABLE_LINEAR = 0x14, +}; + +enum lm3630a_ledb_ctrl { + LM3630A_LEDB_DISABLE = 0x00, + LM3630A_LEDB_ON_A = 0x01, + LM3630A_LEDB_ENABLE = 0x02, + LM3630A_LEDB_ENABLE_LINEAR = 0x0A, +}; + +#define LM3630A_MAX_BRIGHTNESS 255 +/* + *@leda_init_brt : led a init brightness. 4~255 + *@leda_max_brt : led a max brightness. 4~255 + *@leda_ctrl : led a disable, enable linear, enable exponential + *@ledb_init_brt : led b init brightness. 4~255 + *@ledb_max_brt : led b max brightness. 4~255 + *@ledb_ctrl : led b disable, enable linear, enable exponential + *@pwm_period : pwm period + *@pwm_ctrl : pwm disable, bank a or b, active high or low + */ +struct lm3630a_platform_data { + + /* led a config. */ + int leda_init_brt; + int leda_max_brt; + enum lm3630a_leda_ctrl leda_ctrl; + /* led b config. */ + int ledb_init_brt; + int ledb_max_brt; + enum lm3630a_ledb_ctrl ledb_ctrl; + /* pwm config. */ + unsigned int pwm_period; + enum lm3630a_pwm_ctrl pwm_ctrl; +}; + +#endif /* __LINUX_LM3630A_H */ diff --git a/include/linux/platform_data/lp855x.h b/include/linux/platform_data/lp855x.h index ea3200527dd3..1b2ba24e4e03 100644 --- a/include/linux/platform_data/lp855x.h +++ b/include/linux/platform_data/lp855x.h @@ -40,6 +40,17 @@ #define LP8553_PWM_CONFIG LP8550_PWM_CONFIG #define LP8553_I2C_CONFIG LP8550_I2C_CONFIG +/* CONFIG register - LP8555 */ +#define LP8555_PWM_STANDBY BIT(7) +#define LP8555_PWM_FILTER BIT(6) +#define LP8555_RELOAD_EPROM BIT(3) /* use it if EPROMs should be reset + when the backlight turns on */ +#define LP8555_OFF_OPENLEDS BIT(2) +#define LP8555_PWM_CONFIG LP8555_PWM_ONLY +#define LP8555_I2C_CONFIG LP8555_I2C_ONLY +#define LP8555_COMB1_CONFIG LP8555_COMBINED1 +#define LP8555_COMB2_CONFIG LP8555_COMBINED2 + /* DEVICE CONTROL register - LP8556 */ #define LP8556_PWM_CONFIG (LP8556_PWM_ONLY << BRT_MODE_SHFT) #define LP8556_COMB1_CONFIG (LP8556_COMBINED1 << BRT_MODE_SHFT) @@ -65,6 +76,7 @@ enum lp855x_chip_id { LP8551, LP8552, LP8553, + LP8555, LP8556, LP8557, }; @@ -89,6 +101,13 @@ enum lp8553_brighntess_source { LP8553_I2C_ONLY = LP8550_I2C_ONLY, }; +enum lp8555_brightness_source { + LP8555_PWM_ONLY, + LP8555_I2C_ONLY, + LP8555_COMBINED1, /* Brightness register with shaped PWM */ + LP8555_COMBINED2, /* PWM with shaped brightness register */ +}; + enum lp8556_brightness_source { LP8556_PWM_ONLY, LP8556_COMBINED1, /* pwm + i2c before the shaper block */ diff --git a/include/linux/platform_data/mipi-csis.h b/include/linux/platform_data/mipi-csis.h index bf34e17cee7f..c2fd9024717c 100644 --- a/include/linux/platform_data/mipi-csis.h +++ b/include/linux/platform_data/mipi-csis.h @@ -25,13 +25,4 @@ struct s5p_platform_mipi_csis { u8 hs_settle; }; -/** - * s5p_csis_phy_enable - global MIPI-CSI receiver D-PHY control - * @id: MIPI-CSIS harware instance index (0...1) - * @on: true to enable D-PHY and deassert its reset - * false to disable D-PHY - * @return: 0 on success, or negative error code on failure - */ -int s5p_csis_phy_enable(int id, bool on); - #endif /* __PLAT_SAMSUNG_MIPI_CSIS_H_ */ diff --git a/include/linux/platform_data/mmc-esdhc-imx.h b/include/linux/platform_data/mmc-esdhc-imx.h index d44912d81578..75f70f6ac137 100644 --- a/include/linux/platform_data/mmc-esdhc-imx.h +++ b/include/linux/platform_data/mmc-esdhc-imx.h @@ -10,6 +10,8 @@ #ifndef __ASM_ARCH_IMX_ESDHC_H #define __ASM_ARCH_IMX_ESDHC_H +#include <linux/types.h> + enum wp_types { ESDHC_WP_NONE, /* no WP, neither controller nor gpio */ ESDHC_WP_CONTROLLER, /* mmc controller internal WP */ @@ -32,6 +34,7 @@ enum cd_types { * @cd_gpio: gpio for card_detect interrupt * @wp_type: type of write_protect method (see wp_types enum above) * @cd_type: type of card_detect method (see cd_types enum above) + * @support_vsel: indicate it supports 1.8v switching */ struct esdhc_platform_data { @@ -41,5 +44,7 @@ struct esdhc_platform_data { enum cd_types cd_type; int max_bus_width; unsigned int f_max; + bool support_vsel; + unsigned int delay_line; }; #endif /* __ASM_ARCH_IMX_ESDHC_H */ diff --git a/include/linux/platform_data/mtd-nand-omap2.h b/include/linux/platform_data/mtd-nand-omap2.h index 6bf9ef43ddb1..4da5bfa2147f 100644 --- a/include/linux/platform_data/mtd-nand-omap2.h +++ b/include/linux/platform_data/mtd-nand-omap2.h @@ -23,13 +23,16 @@ enum nand_io { }; enum omap_ecc { - /* 1-bit ecc: stored at end of spare area */ - OMAP_ECC_HAMMING_CODE_DEFAULT = 0, /* Default, s/w method */ - OMAP_ECC_HAMMING_CODE_HW, /* gpmc to detect the error */ - /* 1-bit ecc: stored at beginning of spare area as romcode */ - OMAP_ECC_HAMMING_CODE_HW_ROMCODE, /* gpmc method & romcode layout */ - OMAP_ECC_BCH4_CODE_HW, /* 4-bit BCH ecc code */ - OMAP_ECC_BCH8_CODE_HW, /* 8-bit BCH ecc code */ + /* 1-bit ECC calculation by GPMC, Error detection by Software */ + OMAP_ECC_HAM1_CODE_HW = 0, + /* 4-bit ECC calculation by GPMC, Error detection by Software */ + OMAP_ECC_BCH4_CODE_HW_DETECTION_SW, + /* 4-bit ECC calculation by GPMC, Error detection by ELM */ + OMAP_ECC_BCH4_CODE_HW, + /* 8-bit ECC calculation by GPMC, Error detection by Software */ + OMAP_ECC_BCH8_CODE_HW_DETECTION_SW, + /* 8-bit ECC calculation by GPMC, Error detection by ELM */ + OMAP_ECC_BCH8_CODE_HW, }; struct gpmc_nand_regs { @@ -63,5 +66,6 @@ struct omap_nand_platform_data { /* for passing the partitions */ struct device_node *of_node; + struct device_node *elm_of_node; }; #endif diff --git a/include/linux/platform_data/mtd-nand-pxa3xx.h b/include/linux/platform_data/mtd-nand-pxa3xx.h index c42f39f20195..ffb801998e5d 100644 --- a/include/linux/platform_data/mtd-nand-pxa3xx.h +++ b/include/linux/platform_data/mtd-nand-pxa3xx.h @@ -16,19 +16,6 @@ struct pxa3xx_nand_timing { unsigned int tAR; /* ND_ALE low to ND_nRE low delay */ }; -struct pxa3xx_nand_cmdset { - uint16_t read1; - uint16_t read2; - uint16_t program; - uint16_t read_status; - uint16_t read_id; - uint16_t erase; - uint16_t reset; - uint16_t lock; - uint16_t unlock; - uint16_t lock_status; -}; - struct pxa3xx_nand_flash { char *name; uint32_t chip_id; diff --git a/include/linux/platform_data/pinctrl-adi2.h b/include/linux/platform_data/pinctrl-adi2.h new file mode 100644 index 000000000000..8f91300617ec --- /dev/null +++ b/include/linux/platform_data/pinctrl-adi2.h @@ -0,0 +1,40 @@ +/* + * Pinctrl Driver for ADI GPIO2 controller + * + * Copyright 2007-2013 Analog Devices Inc. + * + * Licensed under the GPLv2 or later + */ + + +#ifndef PINCTRL_ADI2_H +#define PINCTRL_ADI2_H + +#include <linux/io.h> +#include <linux/platform_device.h> + +/** + * struct adi_pinctrl_gpio_platform_data - Pinctrl gpio platform data + * for ADI GPIO2 device. + * + * @port_gpio_base: Optional global GPIO index of the GPIO bank. + * 0 means driver decides. + * @port_pin_base: Pin index of the pin controller device. + * @port_width: PIN number of the GPIO bank device + * @pint_id: GPIO PINT device id that this GPIO bank should map to. + * @pint_assign: The 32-bit GPIO PINT registers can be divided into 2 parts. A + * GPIO bank can be mapped into either low 16 bits[0] or high 16 + * bits[1] of each PINT register. + * @pint_map: GIOP bank mapping code in PINT device + */ +struct adi_pinctrl_gpio_platform_data { + unsigned int port_gpio_base; + unsigned int port_pin_base; + unsigned int port_width; + u8 pinctrl_id; + u8 pint_id; + bool pint_assign; + u8 pint_map; +}; + +#endif diff --git a/include/linux/platform_data/pinctrl-single.h b/include/linux/platform_data/pinctrl-single.h new file mode 100644 index 000000000000..72eacda9b360 --- /dev/null +++ b/include/linux/platform_data/pinctrl-single.h @@ -0,0 +1,12 @@ +/** + * irq: optional wake-up interrupt + * rearm: optional soc specific rearm function + * + * Note that the irq and rearm setup should come from device + * tree except for omap where there are still some dependencies + * to the legacy PRM code. + */ +struct pcs_pdata { + int irq; + void (*rearm)(void); +}; diff --git a/include/linux/platform_data/usb-ehci-s5p.h b/include/linux/platform_data/usb-ehci-s5p.h deleted file mode 100644 index 5f28cae18582..000000000000 --- a/include/linux/platform_data/usb-ehci-s5p.h +++ /dev/null @@ -1,21 +0,0 @@ -/* - * Copyright (C) 2011 Samsung Electronics Co.Ltd - * Author: Joonyoung Shim <jy0922.shim@samsung.com> - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - */ - -#ifndef __PLAT_SAMSUNG_EHCI_H -#define __PLAT_SAMSUNG_EHCI_H __FILE__ - -struct s5p_ehci_platdata { - int (*phy_init)(struct platform_device *pdev, int type); - int (*phy_exit)(struct platform_device *pdev, int type); -}; - -extern void s5p_ehci_set_platdata(struct s5p_ehci_platdata *pd); - -#endif /* __PLAT_SAMSUNG_EHCI_H */ diff --git a/include/linux/platform_data/usb-ohci-exynos.h b/include/linux/platform_data/usb-ohci-exynos.h deleted file mode 100644 index c256c595be5e..000000000000 --- a/include/linux/platform_data/usb-ohci-exynos.h +++ /dev/null @@ -1,21 +0,0 @@ -/* - * Copyright (C) 2011 Samsung Electronics Co.Ltd - * http://www.samsung.com/ - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - */ - -#ifndef __MACH_EXYNOS_OHCI_H -#define __MACH_EXYNOS_OHCI_H - -struct exynos4_ohci_platdata { - int (*phy_init)(struct platform_device *pdev, int type); - int (*phy_exit)(struct platform_device *pdev, int type); -}; - -extern void exynos4_ohci_set_platdata(struct exynos4_ohci_platdata *pd); - -#endif /* __MACH_EXYNOS_OHCI_H */ diff --git a/include/linux/platform_data/usb-rcar-gen2-phy.h b/include/linux/platform_data/usb-rcar-gen2-phy.h new file mode 100644 index 000000000000..dd3ba46c0d90 --- /dev/null +++ b/include/linux/platform_data/usb-rcar-gen2-phy.h @@ -0,0 +1,22 @@ +/* + * Copyright (C) 2013 Renesas Solutions Corp. + * Copyright (C) 2013 Cogent Embedded, Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef __USB_RCAR_GEN2_PHY_H +#define __USB_RCAR_GEN2_PHY_H + +#include <linux/types.h> + +struct rcar_gen2_phy_platform_data { + /* USB channel 0 configuration */ + bool chan0_pci:1; /* true: PCI USB host 0, false: USBHS */ + /* USB channel 2 configuration */ + bool chan2_pci:1; /* true: PCI USB host 2, false: USBSS */ +}; + +#endif diff --git a/include/linux/platform_data/zforce_ts.h b/include/linux/platform_data/zforce_ts.h new file mode 100644 index 000000000000..0472ab2f6ede --- /dev/null +++ b/include/linux/platform_data/zforce_ts.h @@ -0,0 +1,26 @@ +/* drivers/input/touchscreen/zforce.c + * + * Copyright (C) 2012-2013 MundoReader S.L. + * + * This software is licensed under the terms of the GNU General Public + * License version 2, as published by the Free Software Foundation, and + * may be copied, distributed, and modified under those terms. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#ifndef _LINUX_INPUT_ZFORCE_TS_H +#define _LINUX_INPUT_ZFORCE_TS_H + +struct zforce_ts_platdata { + int gpio_int; + int gpio_rst; + + unsigned int x_max; + unsigned int y_max; +}; + +#endif /* _LINUX_INPUT_ZFORCE_TS_H */ |