diff options
Diffstat (limited to 'drivers/usb/core/hub.c')
| -rw-r--r-- | drivers/usb/core/hub.c | 161 |
1 files changed, 119 insertions, 42 deletions
diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c index fc7d6cdacf16..86658a81d284 100644 --- a/drivers/usb/core/hub.c +++ b/drivers/usb/core/hub.c @@ -41,11 +41,14 @@ #define USB_VENDOR_GENESYS_LOGIC 0x05e3 #define USB_VENDOR_SMSC 0x0424 #define USB_PRODUCT_USB5534B 0x5534 +#define USB_VENDOR_CYPRESS 0x04b4 +#define USB_PRODUCT_CY7C65632 0x6570 #define HUB_QUIRK_CHECK_PORT_AUTOSUSPEND 0x01 #define HUB_QUIRK_DISABLE_AUTOSUSPEND 0x02 #define USB_TP_TRANSMISSION_DELAY 40 /* ns */ #define USB_TP_TRANSMISSION_DELAY_MAX 65535 /* ns */ +#define USB_PING_RESPONSE_TIME 400 /* ns */ /* Protect struct usb_device->state and ->children members * Note: Both are also protected by ->dev.sem, except that ->state can @@ -180,8 +183,9 @@ int usb_device_supports_lpm(struct usb_device *udev) } /* - * Set the Maximum Exit Latency (MEL) for the host to initiate a transition from - * either U1 or U2. + * Set the Maximum Exit Latency (MEL) for the host to wakup up the path from + * U1/U2, send a PING to the device and receive a PING_RESPONSE. + * See USB 3.1 section C.1.5.2 */ static void usb_set_lpm_mel(struct usb_device *udev, struct usb3_lpm_parameters *udev_lpm_params, @@ -191,35 +195,37 @@ static void usb_set_lpm_mel(struct usb_device *udev, unsigned int hub_exit_latency) { unsigned int total_mel; - unsigned int device_mel; - unsigned int hub_mel; /* - * Calculate the time it takes to transition all links from the roothub - * to the parent hub into U0. The parent hub must then decode the - * packet (hub header decode latency) to figure out which port it was - * bound for. - * - * The Hub Header decode latency is expressed in 0.1us intervals (0x1 - * means 0.1us). Multiply that by 100 to get nanoseconds. + * tMEL1. time to transition path from host to device into U0. + * MEL for parent already contains the delay up to parent, so only add + * the exit latency for the last link (pick the slower exit latency), + * and the hub header decode latency. See USB 3.1 section C 2.2.1 + * Store MEL in nanoseconds */ total_mel = hub_lpm_params->mel + - (hub->descriptor->u.ss.bHubHdrDecLat * 100); + max(udev_exit_latency, hub_exit_latency) * 1000 + + hub->descriptor->u.ss.bHubHdrDecLat * 100; /* - * How long will it take to transition the downstream hub's port into - * U0? The greater of either the hub exit latency or the device exit - * latency. - * - * The BOS U1/U2 exit latencies are expressed in 1us intervals. - * Multiply that by 1000 to get nanoseconds. + * tMEL2. Time to submit PING packet. Sum of tTPTransmissionDelay for + * each link + wHubDelay for each hub. Add only for last link. + * tMEL4, the time for PING_RESPONSE to traverse upstream is similar. + * Multiply by 2 to include it as well. */ - device_mel = udev_exit_latency * 1000; - hub_mel = hub_exit_latency * 1000; - if (device_mel > hub_mel) - total_mel += device_mel; - else - total_mel += hub_mel; + total_mel += (__le16_to_cpu(hub->descriptor->u.ss.wHubDelay) + + USB_TP_TRANSMISSION_DELAY) * 2; + + /* + * tMEL3, tPingResponse. Time taken by device to generate PING_RESPONSE + * after receiving PING. Also add 2100ns as stated in USB 3.1 C 1.5.2.4 + * to cover the delay if the PING_RESPONSE is queued behind a Max Packet + * Size DP. + * Note these delays should be added only once for the entire path, so + * add them to the MEL of the device connected to the roothub. + */ + if (!hub->hdev->parent) + total_mel += USB_PING_RESPONSE_TIME + 2100; udev_lpm_params->mel = total_mel; } @@ -2432,6 +2438,8 @@ static void set_usb_port_removable(struct usb_device *udev) u16 wHubCharacteristics; bool removable = true; + dev_set_removable(&udev->dev, DEVICE_REMOVABLE_UNKNOWN); + if (!hdev) return; @@ -2443,11 +2451,11 @@ static void set_usb_port_removable(struct usb_device *udev) */ switch (hub->ports[udev->portnum - 1]->connect_type) { case USB_PORT_CONNECT_TYPE_HOT_PLUG: - udev->removable = USB_DEVICE_REMOVABLE; + dev_set_removable(&udev->dev, DEVICE_REMOVABLE); return; case USB_PORT_CONNECT_TYPE_HARD_WIRED: case USB_PORT_NOT_USED: - udev->removable = USB_DEVICE_FIXED; + dev_set_removable(&udev->dev, DEVICE_FIXED); return; default: break; @@ -2472,9 +2480,9 @@ static void set_usb_port_removable(struct usb_device *udev) } if (removable) - udev->removable = USB_DEVICE_REMOVABLE; + dev_set_removable(&udev->dev, DEVICE_REMOVABLE); else - udev->removable = USB_DEVICE_FIXED; + dev_set_removable(&udev->dev, DEVICE_FIXED); } @@ -2546,8 +2554,7 @@ int usb_new_device(struct usb_device *udev) device_enable_async_suspend(&udev->dev); /* check whether the hub or firmware marks this port as non-removable */ - if (udev->parent) - set_usb_port_removable(udev); + set_usb_port_removable(udev); /* Register the device. The device driver is responsible * for configuring the device and invoking the add-device @@ -3385,6 +3392,26 @@ int usb_port_suspend(struct usb_device *udev, pm_message_t msg) status = 0; } if (status) { + /* Check if the port has been suspended for the timeout case + * to prevent the suspended port from incorrect handling. + */ + if (status == -ETIMEDOUT) { + int ret; + u16 portstatus, portchange; + + portstatus = portchange = 0; + ret = hub_port_status(hub, port1, &portstatus, + &portchange); + + dev_dbg(&port_dev->dev, + "suspend timeout, status %04x\n", portstatus); + + if (ret == 0 && port_is_suspended(hub, portstatus)) { + status = 0; + goto suspend_done; + } + } + dev_dbg(&port_dev->dev, "can't suspend, status %d\n", status); /* Try to enable USB3 LTM again */ @@ -3401,6 +3428,7 @@ int usb_port_suspend(struct usb_device *udev, pm_message_t msg) if (!PMSG_IS_AUTO(msg)) status = 0; } else { + suspend_done: dev_dbg(&udev->dev, "usb %ssuspend, wakeup %d\n", (PMSG_IS_AUTO(msg) ? "auto-" : ""), udev->do_remote_wakeup); @@ -4089,6 +4117,47 @@ static int usb_set_lpm_timeout(struct usb_device *udev, } /* + * Don't allow device intiated U1/U2 if the system exit latency + one bus + * interval is greater than the minimum service interval of any active + * periodic endpoint. See USB 3.2 section 9.4.9 + */ +static bool usb_device_may_initiate_lpm(struct usb_device *udev, + enum usb3_link_state state) +{ + unsigned int sel; /* us */ + int i, j; + + if (state == USB3_LPM_U1) + sel = DIV_ROUND_UP(udev->u1_params.sel, 1000); + else if (state == USB3_LPM_U2) + sel = DIV_ROUND_UP(udev->u2_params.sel, 1000); + else + return false; + + for (i = 0; i < udev->actconfig->desc.bNumInterfaces; i++) { + struct usb_interface *intf; + struct usb_endpoint_descriptor *desc; + unsigned int interval; + + intf = udev->actconfig->interface[i]; + if (!intf) + continue; + + for (j = 0; j < intf->cur_altsetting->desc.bNumEndpoints; j++) { + desc = &intf->cur_altsetting->endpoint[j].desc; + + if (usb_endpoint_xfer_int(desc) || + usb_endpoint_xfer_isoc(desc)) { + interval = (1 << (desc->bInterval - 1)) * 125; + if (sel + 125 > interval) + return false; + } + } + } + return true; +} + +/* * Enable the hub-initiated U1/U2 idle timeouts, and enable device-initiated * U1/U2 entry. * @@ -4160,20 +4229,23 @@ static void usb_enable_link_state(struct usb_hcd *hcd, struct usb_device *udev, * U1/U2_ENABLE */ if (udev->actconfig && - usb_set_device_initiated_lpm(udev, state, true) == 0) { - if (state == USB3_LPM_U1) - udev->usb3_lpm_u1_enabled = 1; - else if (state == USB3_LPM_U2) - udev->usb3_lpm_u2_enabled = 1; - } else { - /* Don't request U1/U2 entry if the device - * cannot transition to U1/U2. - */ - usb_set_lpm_timeout(udev, state, 0); - hcd->driver->disable_usb3_lpm_timeout(hcd, udev, state); + usb_device_may_initiate_lpm(udev, state)) { + if (usb_set_device_initiated_lpm(udev, state, true)) { + /* + * Request to enable device initiated U1/U2 failed, + * better to turn off lpm in this case. + */ + usb_set_lpm_timeout(udev, state, 0); + hcd->driver->disable_usb3_lpm_timeout(hcd, udev, state); + return; + } } -} + if (state == USB3_LPM_U1) + udev->usb3_lpm_u1_enabled = 1; + else if (state == USB3_LPM_U2) + udev->usb3_lpm_u2_enabled = 1; +} /* * Disable the hub-initiated U1/U2 idle timeouts, and disable device-initiated * U1/U2 entry. @@ -5698,6 +5770,11 @@ static const struct usb_device_id hub_id_table[] = { .bInterfaceClass = USB_CLASS_HUB, .driver_info = HUB_QUIRK_DISABLE_AUTOSUSPEND}, { .match_flags = USB_DEVICE_ID_MATCH_VENDOR + | USB_DEVICE_ID_MATCH_PRODUCT, + .idVendor = USB_VENDOR_CYPRESS, + .idProduct = USB_PRODUCT_CY7C65632, + .driver_info = HUB_QUIRK_DISABLE_AUTOSUSPEND}, + { .match_flags = USB_DEVICE_ID_MATCH_VENDOR | USB_DEVICE_ID_MATCH_INT_CLASS, .idVendor = USB_VENDOR_GENESYS_LOGIC, .bInterfaceClass = USB_CLASS_HUB, |