diff options
Diffstat (limited to 'drivers/pci/controller/pci-mvebu.c')
| -rw-r--r-- | drivers/pci/controller/pci-mvebu.c | 542 |
1 files changed, 404 insertions, 138 deletions
diff --git a/drivers/pci/controller/pci-mvebu.c b/drivers/pci/controller/pci-mvebu.c index ed13e81cd691..71258ea3d35f 100644 --- a/drivers/pci/controller/pci-mvebu.c +++ b/drivers/pci/controller/pci-mvebu.c @@ -6,6 +6,7 @@ */ #include <linux/kernel.h> +#include <linux/module.h> #include <linux/pci.h> #include <linux/clk.h> #include <linux/delay.h> @@ -51,10 +52,14 @@ PCIE_CONF_FUNC(PCI_FUNC(devfn)) | PCIE_CONF_REG(where) | \ PCIE_CONF_ADDR_EN) #define PCIE_CONF_DATA_OFF 0x18fc +#define PCIE_INT_CAUSE_OFF 0x1900 +#define PCIE_INT_PM_PME BIT(28) #define PCIE_MASK_OFF 0x1910 #define PCIE_MASK_ENABLE_INTS 0x0f000000 #define PCIE_CTRL_OFF 0x1a00 #define PCIE_CTRL_X1_MODE 0x0001 +#define PCIE_CTRL_RC_MODE BIT(1) +#define PCIE_CTRL_MASTER_HOT_RESET BIT(24) #define PCIE_STAT_OFF 0x1a04 #define PCIE_STAT_BUS 0xff00 #define PCIE_STAT_DEV 0x1f0000 @@ -125,6 +130,11 @@ static bool mvebu_pcie_link_up(struct mvebu_pcie_port *port) return !(mvebu_readl(port, PCIE_STAT_OFF) & PCIE_STAT_LINK_DOWN); } +static u8 mvebu_pcie_get_local_bus_nr(struct mvebu_pcie_port *port) +{ + return (mvebu_readl(port, PCIE_STAT_OFF) & PCIE_STAT_BUS) >> 8; +} + static void mvebu_pcie_set_local_bus_nr(struct mvebu_pcie_port *port, int nr) { u32 stat; @@ -145,22 +155,13 @@ static void mvebu_pcie_set_local_dev_nr(struct mvebu_pcie_port *port, int nr) mvebu_writel(port, stat, PCIE_STAT_OFF); } -/* - * Setup PCIE BARs and Address Decode Wins: - * BAR[0] -> internal registers (needed for MSI) - * BAR[1] -> covers all DRAM banks - * BAR[2] -> Disabled - * WIN[0-3] -> DRAM bank[0-3] - */ -static void mvebu_pcie_setup_wins(struct mvebu_pcie_port *port) +static void mvebu_pcie_disable_wins(struct mvebu_pcie_port *port) { - const struct mbus_dram_target_info *dram; - u32 size; int i; - dram = mv_mbus_dram_info(); + mvebu_writel(port, 0, PCIE_BAR_LO_OFF(0)); + mvebu_writel(port, 0, PCIE_BAR_HI_OFF(0)); - /* First, disable and clear BARs and windows. */ for (i = 1; i < 3; i++) { mvebu_writel(port, 0, PCIE_BAR_CTRL_OFF(i)); mvebu_writel(port, 0, PCIE_BAR_LO_OFF(i)); @@ -176,6 +177,25 @@ static void mvebu_pcie_setup_wins(struct mvebu_pcie_port *port) mvebu_writel(port, 0, PCIE_WIN5_CTRL_OFF); mvebu_writel(port, 0, PCIE_WIN5_BASE_OFF); mvebu_writel(port, 0, PCIE_WIN5_REMAP_OFF); +} + +/* + * Setup PCIE BARs and Address Decode Wins: + * BAR[0] -> internal registers (needed for MSI) + * BAR[1] -> covers all DRAM banks + * BAR[2] -> Disabled + * WIN[0-3] -> DRAM bank[0-3] + */ +static void mvebu_pcie_setup_wins(struct mvebu_pcie_port *port) +{ + const struct mbus_dram_target_info *dram; + u32 size; + int i; + + dram = mv_mbus_dram_info(); + + /* First, disable and clear BARs and windows. */ + mvebu_pcie_disable_wins(port); /* Setup windows for DDR banks. Count total DDR size on the fly. */ size = 0; @@ -213,18 +233,47 @@ static void mvebu_pcie_setup_wins(struct mvebu_pcie_port *port) static void mvebu_pcie_setup_hw(struct mvebu_pcie_port *port) { - u32 cmd, mask; + u32 ctrl, cmd, dev_rev, mask; - /* Point PCIe unit MBUS decode windows to DRAM space. */ - mvebu_pcie_setup_wins(port); + /* Setup PCIe controller to Root Complex mode. */ + ctrl = mvebu_readl(port, PCIE_CTRL_OFF); + ctrl |= PCIE_CTRL_RC_MODE; + mvebu_writel(port, ctrl, PCIE_CTRL_OFF); - /* Master + slave enable. */ + /* Disable Root Bridge I/O space, memory space and bus mastering. */ cmd = mvebu_readl(port, PCIE_CMD_OFF); - cmd |= PCI_COMMAND_IO; - cmd |= PCI_COMMAND_MEMORY; - cmd |= PCI_COMMAND_MASTER; + cmd &= ~(PCI_COMMAND_IO | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER); mvebu_writel(port, cmd, PCIE_CMD_OFF); + /* + * Change Class Code of PCI Bridge device to PCI Bridge (0x6004) + * because default value is Memory controller (0x5080). + * + * Note that this mvebu PCI Bridge does not have compliant Type 1 + * Configuration Space. Header Type is reported as Type 0 and it + * has format of Type 0 config space. + * + * Moreover Type 0 BAR registers (ranges 0x10 - 0x28 and 0x30 - 0x34) + * have the same format in Marvell's specification as in PCIe + * specification, but their meaning is totally different and they do + * different things: they are aliased into internal mvebu registers + * (e.g. PCIE_BAR_LO_OFF) and these should not be changed or + * reconfigured by pci device drivers. + * + * Therefore driver uses emulation of PCI Bridge which emulates + * access to configuration space via internal mvebu registers or + * emulated configuration buffer. Driver access these PCI Bridge + * directly for simplification, but these registers can be accessed + * also via standard mvebu way for accessing PCI config space. + */ + dev_rev = mvebu_readl(port, PCIE_DEV_REV_OFF); + dev_rev &= ~0xffffff00; + dev_rev |= (PCI_CLASS_BRIDGE_PCI << 8) << 8; + mvebu_writel(port, dev_rev, PCIE_DEV_REV_OFF); + + /* Point PCIe unit MBUS decode windows to DRAM space. */ + mvebu_pcie_setup_wins(port); + /* Enable interrupt lines A-D. */ mask = mvebu_readl(port, PCIE_MASK_OFF); mask |= PCIE_MASK_ENABLE_INTS; @@ -250,6 +299,9 @@ static int mvebu_pcie_hw_rd_conf(struct mvebu_pcie_port *port, case 4: *val = readl_relaxed(conf_data); break; + default: + *val = 0xffffffff; + return PCIBIOS_BAD_REGISTER_NUMBER; } return PCIBIOS_SUCCESSFUL; @@ -303,7 +355,7 @@ static void mvebu_pcie_del_windows(struct mvebu_pcie_port *port, * areas each having a power of two size. We start from the largest * one (i.e highest order bit set in the size). */ -static void mvebu_pcie_add_windows(struct mvebu_pcie_port *port, +static int mvebu_pcie_add_windows(struct mvebu_pcie_port *port, unsigned int target, unsigned int attribute, phys_addr_t base, size_t size, phys_addr_t remap) @@ -324,7 +376,7 @@ static void mvebu_pcie_add_windows(struct mvebu_pcie_port *port, &base, &end, ret); mvebu_pcie_del_windows(port, base - size_mapped, size_mapped); - return; + return ret; } size -= sz; @@ -333,16 +385,20 @@ static void mvebu_pcie_add_windows(struct mvebu_pcie_port *port, if (remap != MVEBU_MBUS_NO_REMAP) remap += sz; } + + return 0; } -static void mvebu_pcie_set_window(struct mvebu_pcie_port *port, +static int mvebu_pcie_set_window(struct mvebu_pcie_port *port, unsigned int target, unsigned int attribute, const struct mvebu_pcie_window *desired, struct mvebu_pcie_window *cur) { + int ret; + if (desired->base == cur->base && desired->remap == cur->remap && desired->size == cur->size) - return; + return 0; if (cur->size != 0) { mvebu_pcie_del_windows(port, cur->base, cur->size); @@ -357,31 +413,35 @@ static void mvebu_pcie_set_window(struct mvebu_pcie_port *port, } if (desired->size == 0) - return; + return 0; + + ret = mvebu_pcie_add_windows(port, target, attribute, desired->base, + desired->size, desired->remap); + if (ret) { + cur->size = 0; + cur->base = 0; + return ret; + } - mvebu_pcie_add_windows(port, target, attribute, desired->base, - desired->size, desired->remap); *cur = *desired; + return 0; } -static void mvebu_pcie_handle_iobase_change(struct mvebu_pcie_port *port) +static int mvebu_pcie_handle_iobase_change(struct mvebu_pcie_port *port) { struct mvebu_pcie_window desired = {}; struct pci_bridge_emul_conf *conf = &port->bridge.conf; /* Are the new iobase/iolimit values invalid? */ if (conf->iolimit < conf->iobase || - conf->iolimitupper < conf->iobaseupper || - !(conf->command & PCI_COMMAND_IO)) { - mvebu_pcie_set_window(port, port->io_target, port->io_attr, - &desired, &port->iowin); - return; - } + conf->iolimitupper < conf->iobaseupper) + return mvebu_pcie_set_window(port, port->io_target, port->io_attr, + &desired, &port->iowin); if (!mvebu_has_ioport(port)) { dev_WARN(&port->pcie->pdev->dev, "Attempt to set IO when IO is disabled\n"); - return; + return -EOPNOTSUPP; } /* @@ -399,22 +459,19 @@ static void mvebu_pcie_handle_iobase_change(struct mvebu_pcie_port *port) desired.remap) + 1; - mvebu_pcie_set_window(port, port->io_target, port->io_attr, &desired, - &port->iowin); + return mvebu_pcie_set_window(port, port->io_target, port->io_attr, &desired, + &port->iowin); } -static void mvebu_pcie_handle_membase_change(struct mvebu_pcie_port *port) +static int mvebu_pcie_handle_membase_change(struct mvebu_pcie_port *port) { struct mvebu_pcie_window desired = {.remap = MVEBU_MBUS_NO_REMAP}; struct pci_bridge_emul_conf *conf = &port->bridge.conf; /* Are the new membase/memlimit values invalid? */ - if (conf->memlimit < conf->membase || - !(conf->command & PCI_COMMAND_MEMORY)) { - mvebu_pcie_set_window(port, port->mem_target, port->mem_attr, - &desired, &port->memwin); - return; - } + if (conf->memlimit < conf->membase) + return mvebu_pcie_set_window(port, port->mem_target, port->mem_attr, + &desired, &port->memwin); /* * We read the PCI-to-PCI bridge emulated registers, and @@ -426,8 +483,56 @@ static void mvebu_pcie_handle_membase_change(struct mvebu_pcie_port *port) desired.size = (((conf->memlimit & 0xFFF0) << 16) | 0xFFFFF) - desired.base + 1; - mvebu_pcie_set_window(port, port->mem_target, port->mem_attr, &desired, - &port->memwin); + return mvebu_pcie_set_window(port, port->mem_target, port->mem_attr, &desired, + &port->memwin); +} + +static pci_bridge_emul_read_status_t +mvebu_pci_bridge_emul_base_conf_read(struct pci_bridge_emul *bridge, + int reg, u32 *value) +{ + struct mvebu_pcie_port *port = bridge->data; + + switch (reg) { + case PCI_COMMAND: + *value = mvebu_readl(port, PCIE_CMD_OFF); + break; + + case PCI_PRIMARY_BUS: { + /* + * From the whole 32bit register we support reading from HW only + * secondary bus number which is mvebu local bus number. + * Other bits are retrieved only from emulated config buffer. + */ + __le32 *cfgspace = (__le32 *)&bridge->conf; + u32 val = le32_to_cpu(cfgspace[PCI_PRIMARY_BUS / 4]); + val &= ~0xff00; + val |= mvebu_pcie_get_local_bus_nr(port) << 8; + *value = val; + break; + } + + case PCI_INTERRUPT_LINE: { + /* + * From the whole 32bit register we support reading from HW only + * one bit: PCI_BRIDGE_CTL_BUS_RESET. + * Other bits are retrieved only from emulated config buffer. + */ + __le32 *cfgspace = (__le32 *)&bridge->conf; + u32 val = le32_to_cpu(cfgspace[PCI_INTERRUPT_LINE / 4]); + if (mvebu_readl(port, PCIE_CTRL_OFF) & PCIE_CTRL_MASTER_HOT_RESET) + val |= PCI_BRIDGE_CTL_BUS_RESET << 16; + else + val &= ~(PCI_BRIDGE_CTL_BUS_RESET << 16); + *value = val; + break; + } + + default: + return PCI_BRIDGE_EMUL_NOT_HANDLED; + } + + return PCI_BRIDGE_EMUL_HANDLED; } static pci_bridge_emul_read_status_t @@ -442,9 +547,7 @@ mvebu_pci_bridge_emul_pcie_conf_read(struct pci_bridge_emul *bridge, break; case PCI_EXP_DEVCTL: - *value = mvebu_readl(port, PCIE_CAP_PCIEXP + PCI_EXP_DEVCTL) & - ~(PCI_EXP_DEVCTL_URRE | PCI_EXP_DEVCTL_FERE | - PCI_EXP_DEVCTL_NFERE | PCI_EXP_DEVCTL_CERE); + *value = mvebu_readl(port, PCIE_CAP_PCIEXP + PCI_EXP_DEVCTL); break; case PCI_EXP_LNKCAP: @@ -468,6 +571,18 @@ mvebu_pci_bridge_emul_pcie_conf_read(struct pci_bridge_emul *bridge, *value = mvebu_readl(port, PCIE_RC_RTSTA); break; + case PCI_EXP_DEVCAP2: + *value = mvebu_readl(port, PCIE_CAP_PCIEXP + PCI_EXP_DEVCAP2); + break; + + case PCI_EXP_DEVCTL2: + *value = mvebu_readl(port, PCIE_CAP_PCIEXP + PCI_EXP_DEVCTL2); + break; + + case PCI_EXP_LNKCTL2: + *value = mvebu_readl(port, PCIE_CAP_PCIEXP + PCI_EXP_LNKCTL2); + break; + default: return PCI_BRIDGE_EMUL_NOT_HANDLED; } @@ -484,39 +599,62 @@ mvebu_pci_bridge_emul_base_conf_write(struct pci_bridge_emul *bridge, switch (reg) { case PCI_COMMAND: - { - if (!mvebu_has_ioport(port)) - conf->command &= ~PCI_COMMAND_IO; - - if ((old ^ new) & PCI_COMMAND_IO) - mvebu_pcie_handle_iobase_change(port); - if ((old ^ new) & PCI_COMMAND_MEMORY) - mvebu_pcie_handle_membase_change(port); + if (!mvebu_has_ioport(port)) { + conf->command = cpu_to_le16( + le16_to_cpu(conf->command) & ~PCI_COMMAND_IO); + new &= ~PCI_COMMAND_IO; + } + mvebu_writel(port, new, PCIE_CMD_OFF); break; - } case PCI_IO_BASE: - /* - * We keep bit 1 set, it is a read-only bit that - * indicates we support 32 bits addressing for the - * I/O - */ - conf->iobase |= PCI_IO_RANGE_TYPE_32; - conf->iolimit |= PCI_IO_RANGE_TYPE_32; - mvebu_pcie_handle_iobase_change(port); + if ((mask & 0xffff) && mvebu_pcie_handle_iobase_change(port)) { + /* On error disable IO range */ + conf->iobase &= ~0xf0; + conf->iolimit &= ~0xf0; + conf->iobaseupper = cpu_to_le16(0x0000); + conf->iolimitupper = cpu_to_le16(0x0000); + if (mvebu_has_ioport(port)) + conf->iobase |= 0xf0; + } break; case PCI_MEMORY_BASE: - mvebu_pcie_handle_membase_change(port); + if (mvebu_pcie_handle_membase_change(port)) { + /* On error disable mem range */ + conf->membase = cpu_to_le16(le16_to_cpu(conf->membase) & ~0xfff0); + conf->memlimit = cpu_to_le16(le16_to_cpu(conf->memlimit) & ~0xfff0); + conf->membase = cpu_to_le16(le16_to_cpu(conf->membase) | 0xfff0); + } break; case PCI_IO_BASE_UPPER16: - mvebu_pcie_handle_iobase_change(port); + if (mvebu_pcie_handle_iobase_change(port)) { + /* On error disable IO range */ + conf->iobase &= ~0xf0; + conf->iolimit &= ~0xf0; + conf->iobaseupper = cpu_to_le16(0x0000); + conf->iolimitupper = cpu_to_le16(0x0000); + if (mvebu_has_ioport(port)) + conf->iobase |= 0xf0; + } break; case PCI_PRIMARY_BUS: - mvebu_pcie_set_local_bus_nr(port, conf->secondary_bus); + if (mask & 0xff00) + mvebu_pcie_set_local_bus_nr(port, conf->secondary_bus); + break; + + case PCI_INTERRUPT_LINE: + if (mask & (PCI_BRIDGE_CTL_BUS_RESET << 16)) { + u32 ctrl = mvebu_readl(port, PCIE_CTRL_OFF); + if (new & (PCI_BRIDGE_CTL_BUS_RESET << 16)) + ctrl |= PCIE_CTRL_MASTER_HOT_RESET; + else + ctrl &= ~PCIE_CTRL_MASTER_HOT_RESET; + mvebu_writel(port, ctrl, PCIE_CTRL_OFF); + } break; default: @@ -532,13 +670,6 @@ mvebu_pci_bridge_emul_pcie_conf_write(struct pci_bridge_emul *bridge, switch (reg) { case PCI_EXP_DEVCTL: - /* - * Armada370 data says these bits must always - * be zero when in root complex mode. - */ - new &= ~(PCI_EXP_DEVCTL_URRE | PCI_EXP_DEVCTL_FERE | - PCI_EXP_DEVCTL_NFERE | PCI_EXP_DEVCTL_CERE); - mvebu_writel(port, new, PCIE_CAP_PCIEXP + PCI_EXP_DEVCTL); break; @@ -555,12 +686,31 @@ mvebu_pci_bridge_emul_pcie_conf_write(struct pci_bridge_emul *bridge, break; case PCI_EXP_RTSTA: - mvebu_writel(port, new, PCIE_RC_RTSTA); + /* + * PME Status bit in Root Status Register (PCIE_RC_RTSTA) + * is read-only and can be cleared only by writing 0b to the + * Interrupt Cause RW0C register (PCIE_INT_CAUSE_OFF). So + * clear PME via Interrupt Cause. + */ + if (new & PCI_EXP_RTSTA_PME) + mvebu_writel(port, ~PCIE_INT_PM_PME, PCIE_INT_CAUSE_OFF); + break; + + case PCI_EXP_DEVCTL2: + mvebu_writel(port, new, PCIE_CAP_PCIEXP + PCI_EXP_DEVCTL2); + break; + + case PCI_EXP_LNKCTL2: + mvebu_writel(port, new, PCIE_CAP_PCIEXP + PCI_EXP_LNKCTL2); + break; + + default: break; } } static struct pci_bridge_emul_ops mvebu_pci_bridge_emul_ops = { + .read_base = mvebu_pci_bridge_emul_base_conf_read, .write_base = mvebu_pci_bridge_emul_base_conf_write, .read_pcie = mvebu_pci_bridge_emul_pcie_conf_read, .write_pcie = mvebu_pci_bridge_emul_pcie_conf_write, @@ -570,9 +720,11 @@ static struct pci_bridge_emul_ops mvebu_pci_bridge_emul_ops = { * Initialize the configuration space of the PCI-to-PCI bridge * associated with the given PCIe interface. */ -static void mvebu_pci_bridge_emul_init(struct mvebu_pcie_port *port) +static int mvebu_pci_bridge_emul_init(struct mvebu_pcie_port *port) { struct pci_bridge_emul *bridge = &port->bridge; + u32 pcie_cap = mvebu_readl(port, PCIE_CAP_PCIEXP); + u8 pcie_cap_ver = ((pcie_cap >> 16) & PCI_EXP_FLAGS_VERS); bridge->conf.vendor = PCI_VENDOR_ID_MARVELL; bridge->conf.device = mvebu_readl(port, PCIE_DEV_ID_OFF) >> 16; @@ -585,11 +737,17 @@ static void mvebu_pci_bridge_emul_init(struct mvebu_pcie_port *port) bridge->conf.iolimit = PCI_IO_RANGE_TYPE_32; } + /* + * Older mvebu hardware provides PCIe Capability structure only in + * version 1. New hardware provides it in version 2. + */ + bridge->pcie_conf.cap = cpu_to_le16(pcie_cap_ver); + bridge->has_pcie = true; bridge->data = port; bridge->ops = &mvebu_pci_bridge_emul_ops; - pci_bridge_emul_init(bridge, PCI_BRIDGE_EMUL_NO_PREFETCHABLE_BAR); + return pci_bridge_emul_init(bridge, PCI_BRIDGE_EMUL_NO_PREFETCHABLE_BAR); } static inline struct mvebu_pcie *sys_to_pcie(struct pci_sys_data *sys) @@ -606,6 +764,9 @@ static struct mvebu_pcie_port *mvebu_pcie_find_port(struct mvebu_pcie *pcie, for (i = 0; i < pcie->nports; i++) { struct mvebu_pcie_port *port = &pcie->ports[i]; + if (!port->base) + continue; + if (bus->number == 0 && port->devfn == devfn) return port; if (bus->number != 0 && @@ -653,20 +814,16 @@ static int mvebu_pcie_rd_conf(struct pci_bus *bus, u32 devfn, int where, int ret; port = mvebu_pcie_find_port(pcie, bus, devfn); - if (!port) { - *val = 0xffffffff; + if (!port) return PCIBIOS_DEVICE_NOT_FOUND; - } /* Access the emulated PCI-to-PCI bridge */ if (bus->number == 0) return pci_bridge_emul_conf_read(&port->bridge, where, size, val); - if (!mvebu_pcie_link_up(port)) { - *val = 0xffffffff; + if (!mvebu_pcie_link_up(port)) return PCIBIOS_DEVICE_NOT_FOUND; - } /* Access the real PCIe interface */ ret = mvebu_pcie_hw_rd_conf(port, bus, devfn, @@ -680,6 +837,15 @@ static struct pci_ops mvebu_pcie_ops = { .write = mvebu_pcie_wr_conf, }; +static int mvebu_pcie_map_irq(const struct pci_dev *dev, u8 slot, u8 pin) +{ + /* Interrupt support on mvebu emulated bridges is not implemented yet */ + if (dev->bus->number == 0) + return 0; /* Proper return code 0 == NO_IRQ */ + + return of_irq_parse_and_map_pci(dev, slot, pin); +} + static resource_size_t mvebu_pcie_align_resource(struct pci_dev *dev, const struct resource *res, resource_size_t start, @@ -781,6 +947,8 @@ static int mvebu_pcie_suspend(struct device *dev) pcie = dev_get_drvdata(dev); for (i = 0; i < pcie->nports; i++) { struct mvebu_pcie_port *port = pcie->ports + i; + if (!port->base) + continue; port->saved_pcie_stat = mvebu_readl(port, PCIE_STAT_OFF); } @@ -795,6 +963,8 @@ static int mvebu_pcie_resume(struct device *dev) pcie = dev_get_drvdata(dev); for (i = 0; i < pcie->nports; i++) { struct mvebu_pcie_port *port = pcie->ports + i; + if (!port->base) + continue; mvebu_writel(port, port->saved_pcie_stat, PCIE_STAT_OFF); mvebu_pcie_setup_hw(port); } @@ -838,6 +1008,11 @@ static int mvebu_pcie_parse_port(struct mvebu_pcie *pcie, port->devfn = of_pci_get_devfn(child); if (port->devfn < 0) goto skip; + if (PCI_FUNC(port->devfn) != 0) { + dev_err(dev, "%s: invalid function number, must be zero\n", + port->name); + goto skip; + } ret = mvebu_get_tgt_attr(dev->of_node, port->devfn, IORESOURCE_MEM, &port->mem_target, &port->mem_attr); @@ -992,6 +1167,10 @@ static int mvebu_pcie_parse_request_resources(struct mvebu_pcie *pcie) resource_size(&pcie->io) - 1); pcie->realio.name = "PCI I/O"; + ret = devm_pci_remap_iospace(dev, &pcie->realio, pcie->io.start); + if (ret) + return ret; + pci_add_resource(&bridge->windows, &pcie->realio); ret = devm_request_resource(dev, &ioport_resource, &pcie->realio); if (ret) @@ -1001,54 +1180,6 @@ static int mvebu_pcie_parse_request_resources(struct mvebu_pcie *pcie) return 0; } -/* - * This is a copy of pci_host_probe(), except that it does the I/O - * remap as the last step, once we are sure we won't fail. - * - * It should be removed once the I/O remap error handling issue has - * been sorted out. - */ -static int mvebu_pci_host_probe(struct pci_host_bridge *bridge) -{ - struct mvebu_pcie *pcie; - struct pci_bus *bus, *child; - int ret; - - ret = pci_scan_root_bus_bridge(bridge); - if (ret < 0) { - dev_err(bridge->dev.parent, "Scanning root bridge failed"); - return ret; - } - - pcie = pci_host_bridge_priv(bridge); - if (resource_size(&pcie->io) != 0) { - unsigned int i; - - for (i = 0; i < resource_size(&pcie->realio); i += SZ_64K) - pci_ioremap_io(i, pcie->io.start + i); - } - - bus = bridge->bus; - - /* - * We insert PCI resources into the iomem_resource and - * ioport_resource trees in either pci_bus_claim_resources() - * or pci_bus_assign_resources(). - */ - if (pci_has_flag(PCI_PROBE_ONLY)) { - pci_bus_claim_resources(bus); - } else { - pci_bus_size_bridges(bus); - pci_bus_assign_resources(bus); - - list_for_each_entry(child, &bus->children, node) - pcie_bus_configure_settings(child); - } - - pci_bus_add_devices(bus); - return 0; -} - static int mvebu_pcie_probe(struct platform_device *pdev) { struct device *dev = &pdev->dev; @@ -1112,9 +1243,93 @@ static int mvebu_pcie_probe(struct platform_device *pdev) continue; } + ret = mvebu_pci_bridge_emul_init(port); + if (ret < 0) { + dev_err(dev, "%s: cannot init emulated bridge\n", + port->name); + devm_iounmap(dev, port->base); + port->base = NULL; + mvebu_pcie_powerdown(port); + continue; + } + + /* + * PCIe topology exported by mvebu hw is quite complicated. In + * reality has something like N fully independent host bridges + * where each host bridge has one PCIe Root Port (which acts as + * PCI Bridge device). Each host bridge has its own independent + * internal registers, independent access to PCI config space, + * independent interrupt lines, independent window and memory + * access configuration. But additionally there is some kind of + * peer-to-peer support between PCIe devices behind different + * host bridges limited just to forwarding of memory and I/O + * transactions (forwarding of error messages and config cycles + * is not supported). So we could say there are N independent + * PCIe Root Complexes. + * + * For this kind of setup DT should have been structured into + * N independent PCIe controllers / host bridges. But instead + * structure in past was defined to put PCIe Root Ports of all + * host bridges into one bus zero, like in classic multi-port + * Root Complex setup with just one host bridge. + * + * This means that pci-mvebu.c driver provides "virtual" bus 0 + * on which registers all PCIe Root Ports (PCI Bridge devices) + * specified in DT by their BDF addresses and virtually routes + * PCI config access of each PCI bridge device to specific PCIe + * host bridge. + * + * Normally PCI Bridge should choose between Type 0 and Type 1 + * config requests based on primary and secondary bus numbers + * configured on the bridge itself. But because mvebu PCI Bridge + * does not have registers for primary and secondary bus numbers + * in its config space, it determinates type of config requests + * via its own custom way. + * + * There are two options how mvebu determinate type of config + * request. + * + * 1. If Secondary Bus Number Enable bit is not set or is not + * available (applies for pre-XP PCIe controllers) then Type 0 + * is used if target bus number equals Local Bus Number (bits + * [15:8] in register 0x1a04) and target device number differs + * from Local Device Number (bits [20:16] in register 0x1a04). + * Type 1 is used if target bus number differs from Local Bus + * Number. And when target bus number equals Local Bus Number + * and target device equals Local Device Number then request is + * routed to Local PCI Bridge (PCIe Root Port). + * + * 2. If Secondary Bus Number Enable bit is set (bit 7 in + * register 0x1a2c) then mvebu hw determinate type of config + * request like compliant PCI Bridge based on primary bus number + * which is configured via Local Bus Number (bits [15:8] in + * register 0x1a04) and secondary bus number which is configured + * via Secondary Bus Number (bits [7:0] in register 0x1a2c). + * Local PCI Bridge (PCIe Root Port) is available on primary bus + * as device with Local Device Number (bits [20:16] in register + * 0x1a04). + * + * Secondary Bus Number Enable bit is disabled by default and + * option 2. is not available on pre-XP PCIe controllers. Hence + * this driver always use option 1. + * + * Basically it means that primary and secondary buses shares + * one virtual number configured via Local Bus Number bits and + * Local Device Number bits determinates if accessing primary + * or secondary bus. Set Local Device Number to 1 and redirect + * all writes of PCI Bridge Secondary Bus Number register to + * Local Bus Number (bits [15:8] in register 0x1a04). + * + * So when accessing devices on buses behind secondary bus + * number it would work correctly. And also when accessing + * device 0 at secondary bus number via config space would be + * correctly routed to secondary bus. Due to issues described + * in mvebu_pcie_setup_hw(), PCI Bridges at primary bus (zero) + * are not accessed directly via PCI config space but rarher + * indirectly via kernel emulated PCI bridge driver. + */ mvebu_pcie_setup_hw(port); - mvebu_pcie_set_local_dev_nr(port, 1); - mvebu_pci_bridge_emul_init(port); + mvebu_pcie_set_local_dev_nr(port, 0); } pcie->nports = i; @@ -1122,8 +1337,55 @@ static int mvebu_pcie_probe(struct platform_device *pdev) bridge->sysdata = pcie; bridge->ops = &mvebu_pcie_ops; bridge->align_resource = mvebu_pcie_align_resource; + bridge->map_irq = mvebu_pcie_map_irq; + + return pci_host_probe(bridge); +} + +static int mvebu_pcie_remove(struct platform_device *pdev) +{ + struct mvebu_pcie *pcie = platform_get_drvdata(pdev); + struct pci_host_bridge *bridge = pci_host_bridge_from_priv(pcie); + u32 cmd; + int i; + + /* Remove PCI bus with all devices. */ + pci_lock_rescan_remove(); + pci_stop_root_bus(bridge->bus); + pci_remove_root_bus(bridge->bus); + pci_unlock_rescan_remove(); + + for (i = 0; i < pcie->nports; i++) { + struct mvebu_pcie_port *port = &pcie->ports[i]; + + if (!port->base) + continue; + + /* Disable Root Bridge I/O space, memory space and bus mastering. */ + cmd = mvebu_readl(port, PCIE_CMD_OFF); + cmd &= ~(PCI_COMMAND_IO | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER); + mvebu_writel(port, cmd, PCIE_CMD_OFF); + + /* Mask all interrupt sources. */ + mvebu_writel(port, 0, PCIE_MASK_OFF); + + /* Free config space for emulated root bridge. */ + pci_bridge_emul_cleanup(&port->bridge); - return mvebu_pci_host_probe(bridge); + /* Disable and clear BARs and windows. */ + mvebu_pcie_disable_wins(port); + + /* Delete PCIe IO and MEM windows. */ + if (port->iowin.size) + mvebu_pcie_del_windows(port, port->iowin.base, port->iowin.size); + if (port->memwin.size) + mvebu_pcie_del_windows(port, port->memwin.base, port->memwin.size); + + /* Power down card and disable clocks. Must be the last step. */ + mvebu_pcie_powerdown(port); + } + + return 0; } static const struct of_device_id mvebu_pcie_of_match_table[] = { @@ -1142,10 +1404,14 @@ static struct platform_driver mvebu_pcie_driver = { .driver = { .name = "mvebu-pcie", .of_match_table = mvebu_pcie_of_match_table, - /* driver unloading/unbinding currently not supported */ - .suppress_bind_attrs = true, .pm = &mvebu_pcie_pm_ops, }, .probe = mvebu_pcie_probe, + .remove = mvebu_pcie_remove, }; -builtin_platform_driver(mvebu_pcie_driver); +module_platform_driver(mvebu_pcie_driver); + +MODULE_AUTHOR("Thomas Petazzoni <[email protected]>"); +MODULE_AUTHOR("Pali Rohár <[email protected]>"); +MODULE_DESCRIPTION("Marvell EBU PCIe controller"); +MODULE_LICENSE("GPL v2"); |