diff options
Diffstat (limited to 'drivers/net/ethernet/intel/igc/igc_mac.c')
| -rw-r--r-- | drivers/net/ethernet/intel/igc/igc_mac.c | 806 |
1 files changed, 806 insertions, 0 deletions
diff --git a/drivers/net/ethernet/intel/igc/igc_mac.c b/drivers/net/ethernet/intel/igc/igc_mac.c new file mode 100644 index 000000000000..f7683d3ae47c --- /dev/null +++ b/drivers/net/ethernet/intel/igc/igc_mac.c @@ -0,0 +1,806 @@ +// SPDX-License-Identifier: GPL-2.0 +/* Copyright (c) 2018 Intel Corporation */ + +#include <linux/pci.h> +#include <linux/delay.h> + +#include "igc_mac.h" +#include "igc_hw.h" + +/* forward declaration */ +static s32 igc_set_default_fc(struct igc_hw *hw); +static s32 igc_set_fc_watermarks(struct igc_hw *hw); + +/** + * igc_disable_pcie_master - Disables PCI-express master access + * @hw: pointer to the HW structure + * + * Returns 0 (0) if successful, else returns -10 + * (-IGC_ERR_MASTER_REQUESTS_PENDING) if master disable bit has not caused + * the master requests to be disabled. + * + * Disables PCI-Express master access and verifies there are no pending + * requests. + */ +s32 igc_disable_pcie_master(struct igc_hw *hw) +{ + s32 timeout = MASTER_DISABLE_TIMEOUT; + s32 ret_val = 0; + u32 ctrl; + + ctrl = rd32(IGC_CTRL); + ctrl |= IGC_CTRL_GIO_MASTER_DISABLE; + wr32(IGC_CTRL, ctrl); + + while (timeout) { + if (!(rd32(IGC_STATUS) & + IGC_STATUS_GIO_MASTER_ENABLE)) + break; + usleep_range(2000, 3000); + timeout--; + } + + if (!timeout) { + hw_dbg("Master requests are pending.\n"); + ret_val = -IGC_ERR_MASTER_REQUESTS_PENDING; + goto out; + } + +out: + return ret_val; +} + +/** + * igc_init_rx_addrs - Initialize receive addresses + * @hw: pointer to the HW structure + * @rar_count: receive address registers + * + * Setup the receive address registers by setting the base receive address + * register to the devices MAC address and clearing all the other receive + * address registers to 0. + */ +void igc_init_rx_addrs(struct igc_hw *hw, u16 rar_count) +{ + u8 mac_addr[ETH_ALEN] = {0}; + u32 i; + + /* Setup the receive address */ + hw_dbg("Programming MAC Address into RAR[0]\n"); + + hw->mac.ops.rar_set(hw, hw->mac.addr, 0); + + /* Zero out the other (rar_entry_count - 1) receive addresses */ + hw_dbg("Clearing RAR[1-%u]\n", rar_count - 1); + for (i = 1; i < rar_count; i++) + hw->mac.ops.rar_set(hw, mac_addr, i); +} + +/** + * igc_setup_link - Setup flow control and link settings + * @hw: pointer to the HW structure + * + * Determines which flow control settings to use, then configures flow + * control. Calls the appropriate media-specific link configuration + * function. Assuming the adapter has a valid link partner, a valid link + * should be established. Assumes the hardware has previously been reset + * and the transmitter and receiver are not enabled. + */ +s32 igc_setup_link(struct igc_hw *hw) +{ + s32 ret_val = 0; + + /* In the case of the phy reset being blocked, we already have a link. + * We do not need to set it up again. + */ + if (igc_check_reset_block(hw)) + goto out; + + /* If requested flow control is set to default, set flow control + * based on the EEPROM flow control settings. + */ + if (hw->fc.requested_mode == igc_fc_default) { + ret_val = igc_set_default_fc(hw); + if (ret_val) + goto out; + } + + /* We want to save off the original Flow Control configuration just + * in case we get disconnected and then reconnected into a different + * hub or switch with different Flow Control capabilities. + */ + hw->fc.current_mode = hw->fc.requested_mode; + + hw_dbg("After fix-ups FlowControl is now = %x\n", hw->fc.current_mode); + + /* Call the necessary media_type subroutine to configure the link. */ + ret_val = hw->mac.ops.setup_physical_interface(hw); + if (ret_val) + goto out; + + /* Initialize the flow control address, type, and PAUSE timer + * registers to their default values. This is done even if flow + * control is disabled, because it does not hurt anything to + * initialize these registers. + */ + hw_dbg("Initializing the Flow Control address, type and timer regs\n"); + wr32(IGC_FCT, FLOW_CONTROL_TYPE); + wr32(IGC_FCAH, FLOW_CONTROL_ADDRESS_HIGH); + wr32(IGC_FCAL, FLOW_CONTROL_ADDRESS_LOW); + + wr32(IGC_FCTTV, hw->fc.pause_time); + + ret_val = igc_set_fc_watermarks(hw); + +out: + return ret_val; +} + +/** + * igc_set_default_fc - Set flow control default values + * @hw: pointer to the HW structure + * + * Read the EEPROM for the default values for flow control and store the + * values. + */ +static s32 igc_set_default_fc(struct igc_hw *hw) +{ + hw->fc.requested_mode = igc_fc_full; + return 0; +} + +/** + * igc_force_mac_fc - Force the MAC's flow control settings + * @hw: pointer to the HW structure + * + * Force the MAC's flow control settings. Sets the TFCE and RFCE bits in the + * device control register to reflect the adapter settings. TFCE and RFCE + * need to be explicitly set by software when a copper PHY is used because + * autonegotiation is managed by the PHY rather than the MAC. Software must + * also configure these bits when link is forced on a fiber connection. + */ +s32 igc_force_mac_fc(struct igc_hw *hw) +{ + s32 ret_val = 0; + u32 ctrl; + + ctrl = rd32(IGC_CTRL); + + /* Because we didn't get link via the internal auto-negotiation + * mechanism (we either forced link or we got link via PHY + * auto-neg), we have to manually enable/disable transmit an + * receive flow control. + * + * The "Case" statement below enables/disable flow control + * according to the "hw->fc.current_mode" parameter. + * + * The possible values of the "fc" parameter are: + * 0: Flow control is completely disabled + * 1: Rx flow control is enabled (we can receive pause + * frames but not send pause frames). + * 2: Tx flow control is enabled (we can send pause frames + * frames but we do not receive pause frames). + * 3: Both Rx and TX flow control (symmetric) is enabled. + * other: No other values should be possible at this point. + */ + hw_dbg("hw->fc.current_mode = %u\n", hw->fc.current_mode); + + switch (hw->fc.current_mode) { + case igc_fc_none: + ctrl &= (~(IGC_CTRL_TFCE | IGC_CTRL_RFCE)); + break; + case igc_fc_rx_pause: + ctrl &= (~IGC_CTRL_TFCE); + ctrl |= IGC_CTRL_RFCE; + break; + case igc_fc_tx_pause: + ctrl &= (~IGC_CTRL_RFCE); + ctrl |= IGC_CTRL_TFCE; + break; + case igc_fc_full: + ctrl |= (IGC_CTRL_TFCE | IGC_CTRL_RFCE); + break; + default: + hw_dbg("Flow control param set incorrectly\n"); + ret_val = -IGC_ERR_CONFIG; + goto out; + } + + wr32(IGC_CTRL, ctrl); + +out: + return ret_val; +} + +/** + * igc_set_fc_watermarks - Set flow control high/low watermarks + * @hw: pointer to the HW structure + * + * Sets the flow control high/low threshold (watermark) registers. If + * flow control XON frame transmission is enabled, then set XON frame + * transmission as well. + */ +static s32 igc_set_fc_watermarks(struct igc_hw *hw) +{ + u32 fcrtl = 0, fcrth = 0; + + /* Set the flow control receive threshold registers. Normally, + * these registers will be set to a default threshold that may be + * adjusted later by the driver's runtime code. However, if the + * ability to transmit pause frames is not enabled, then these + * registers will be set to 0. + */ + if (hw->fc.current_mode & igc_fc_tx_pause) { + /* We need to set up the Receive Threshold high and low water + * marks as well as (optionally) enabling the transmission of + * XON frames. + */ + fcrtl = hw->fc.low_water; + if (hw->fc.send_xon) + fcrtl |= IGC_FCRTL_XONE; + + fcrth = hw->fc.high_water; + } + wr32(IGC_FCRTL, fcrtl); + wr32(IGC_FCRTH, fcrth); + + return 0; +} + +/** + * igc_clear_hw_cntrs_base - Clear base hardware counters + * @hw: pointer to the HW structure + * + * Clears the base hardware counters by reading the counter registers. + */ +void igc_clear_hw_cntrs_base(struct igc_hw *hw) +{ + rd32(IGC_CRCERRS); + rd32(IGC_SYMERRS); + rd32(IGC_MPC); + rd32(IGC_SCC); + rd32(IGC_ECOL); + rd32(IGC_MCC); + rd32(IGC_LATECOL); + rd32(IGC_COLC); + rd32(IGC_DC); + rd32(IGC_SEC); + rd32(IGC_RLEC); + rd32(IGC_XONRXC); + rd32(IGC_XONTXC); + rd32(IGC_XOFFRXC); + rd32(IGC_XOFFTXC); + rd32(IGC_FCRUC); + rd32(IGC_GPRC); + rd32(IGC_BPRC); + rd32(IGC_MPRC); + rd32(IGC_GPTC); + rd32(IGC_GORCL); + rd32(IGC_GORCH); + rd32(IGC_GOTCL); + rd32(IGC_GOTCH); + rd32(IGC_RNBC); + rd32(IGC_RUC); + rd32(IGC_RFC); + rd32(IGC_ROC); + rd32(IGC_RJC); + rd32(IGC_TORL); + rd32(IGC_TORH); + rd32(IGC_TOTL); + rd32(IGC_TOTH); + rd32(IGC_TPR); + rd32(IGC_TPT); + rd32(IGC_MPTC); + rd32(IGC_BPTC); + + rd32(IGC_PRC64); + rd32(IGC_PRC127); + rd32(IGC_PRC255); + rd32(IGC_PRC511); + rd32(IGC_PRC1023); + rd32(IGC_PRC1522); + rd32(IGC_PTC64); + rd32(IGC_PTC127); + rd32(IGC_PTC255); + rd32(IGC_PTC511); + rd32(IGC_PTC1023); + rd32(IGC_PTC1522); + + rd32(IGC_ALGNERRC); + rd32(IGC_RXERRC); + rd32(IGC_TNCRS); + rd32(IGC_CEXTERR); + rd32(IGC_TSCTC); + rd32(IGC_TSCTFC); + + rd32(IGC_MGTPRC); + rd32(IGC_MGTPDC); + rd32(IGC_MGTPTC); + + rd32(IGC_IAC); + rd32(IGC_ICRXOC); + + rd32(IGC_ICRXPTC); + rd32(IGC_ICRXATC); + rd32(IGC_ICTXPTC); + rd32(IGC_ICTXATC); + rd32(IGC_ICTXQEC); + rd32(IGC_ICTXQMTC); + rd32(IGC_ICRXDMTC); + + rd32(IGC_CBTMPC); + rd32(IGC_HTDPMC); + rd32(IGC_CBRMPC); + rd32(IGC_RPTHC); + rd32(IGC_HGPTC); + rd32(IGC_HTCBDPC); + rd32(IGC_HGORCL); + rd32(IGC_HGORCH); + rd32(IGC_HGOTCL); + rd32(IGC_HGOTCH); + rd32(IGC_LENERRS); +} + +/** + * igc_rar_set - Set receive address register + * @hw: pointer to the HW structure + * @addr: pointer to the receive address + * @index: receive address array register + * + * Sets the receive address array register at index to the address passed + * in by addr. + */ +void igc_rar_set(struct igc_hw *hw, u8 *addr, u32 index) +{ + u32 rar_low, rar_high; + + /* HW expects these in little endian so we reverse the byte order + * from network order (big endian) to little endian + */ + rar_low = ((u32)addr[0] | + ((u32)addr[1] << 8) | + ((u32)addr[2] << 16) | ((u32)addr[3] << 24)); + + rar_high = ((u32)addr[4] | ((u32)addr[5] << 8)); + + /* If MAC address zero, no need to set the AV bit */ + if (rar_low || rar_high) + rar_high |= IGC_RAH_AV; + + /* Some bridges will combine consecutive 32-bit writes into + * a single burst write, which will malfunction on some parts. + * The flushes avoid this. + */ + wr32(IGC_RAL(index), rar_low); + wrfl(); + wr32(IGC_RAH(index), rar_high); + wrfl(); +} + +/** + * igc_check_for_copper_link - Check for link (Copper) + * @hw: pointer to the HW structure + * + * Checks to see of the link status of the hardware has changed. If a + * change in link status has been detected, then we read the PHY registers + * to get the current speed/duplex if link exists. + */ +s32 igc_check_for_copper_link(struct igc_hw *hw) +{ + struct igc_mac_info *mac = &hw->mac; + s32 ret_val; + bool link; + + /* We only want to go out to the PHY registers to see if Auto-Neg + * has completed and/or if our link status has changed. The + * get_link_status flag is set upon receiving a Link Status + * Change or Rx Sequence Error interrupt. + */ + if (!mac->get_link_status) { + ret_val = 0; + goto out; + } + + /* First we want to see if the MII Status Register reports + * link. If so, then we want to get the current speed/duplex + * of the PHY. + */ + ret_val = igc_phy_has_link(hw, 1, 0, &link); + if (ret_val) + goto out; + + if (!link) + goto out; /* No link detected */ + + mac->get_link_status = false; + + /* Check if there was DownShift, must be checked + * immediately after link-up + */ + igc_check_downshift(hw); + + /* If we are forcing speed/duplex, then we simply return since + * we have already determined whether we have link or not. + */ + if (!mac->autoneg) { + ret_val = -IGC_ERR_CONFIG; + goto out; + } + + /* Auto-Neg is enabled. Auto Speed Detection takes care + * of MAC speed/duplex configuration. So we only need to + * configure Collision Distance in the MAC. + */ + igc_config_collision_dist(hw); + + /* Configure Flow Control now that Auto-Neg has completed. + * First, we need to restore the desired flow control + * settings because we may have had to re-autoneg with a + * different link partner. + */ + ret_val = igc_config_fc_after_link_up(hw); + if (ret_val) + hw_dbg("Error configuring flow control\n"); + +out: + return ret_val; +} + +/** + * igc_config_collision_dist - Configure collision distance + * @hw: pointer to the HW structure + * + * Configures the collision distance to the default value and is used + * during link setup. Currently no func pointer exists and all + * implementations are handled in the generic version of this function. + */ +void igc_config_collision_dist(struct igc_hw *hw) +{ + u32 tctl; + + tctl = rd32(IGC_TCTL); + + tctl &= ~IGC_TCTL_COLD; + tctl |= IGC_COLLISION_DISTANCE << IGC_COLD_SHIFT; + + wr32(IGC_TCTL, tctl); + wrfl(); +} + +/** + * igc_config_fc_after_link_up - Configures flow control after link + * @hw: pointer to the HW structure + * + * Checks the status of auto-negotiation after link up to ensure that the + * speed and duplex were not forced. If the link needed to be forced, then + * flow control needs to be forced also. If auto-negotiation is enabled + * and did not fail, then we configure flow control based on our link + * partner. + */ +s32 igc_config_fc_after_link_up(struct igc_hw *hw) +{ + u16 mii_status_reg, mii_nway_adv_reg, mii_nway_lp_ability_reg; + struct igc_mac_info *mac = &hw->mac; + u16 speed, duplex; + s32 ret_val = 0; + + /* Check for the case where we have fiber media and auto-neg failed + * so we had to force link. In this case, we need to force the + * configuration of the MAC to match the "fc" parameter. + */ + if (mac->autoneg_failed) { + if (hw->phy.media_type == igc_media_type_copper) + ret_val = igc_force_mac_fc(hw); + } + + if (ret_val) { + hw_dbg("Error forcing flow control settings\n"); + goto out; + } + + /* Check for the case where we have copper media and auto-neg is + * enabled. In this case, we need to check and see if Auto-Neg + * has completed, and if so, how the PHY and link partner has + * flow control configured. + */ + if (hw->phy.media_type == igc_media_type_copper && mac->autoneg) { + /* Read the MII Status Register and check to see if AutoNeg + * has completed. We read this twice because this reg has + * some "sticky" (latched) bits. + */ + ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS, + &mii_status_reg); + if (ret_val) + goto out; + ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS, + &mii_status_reg); + if (ret_val) + goto out; + + if (!(mii_status_reg & MII_SR_AUTONEG_COMPLETE)) { + hw_dbg("Copper PHY and Auto Neg has not completed.\n"); + goto out; + } + + /* The AutoNeg process has completed, so we now need to + * read both the Auto Negotiation Advertisement + * Register (Address 4) and the Auto_Negotiation Base + * Page Ability Register (Address 5) to determine how + * flow control was negotiated. + */ + ret_val = hw->phy.ops.read_reg(hw, PHY_AUTONEG_ADV, + &mii_nway_adv_reg); + if (ret_val) + goto out; + ret_val = hw->phy.ops.read_reg(hw, PHY_LP_ABILITY, + &mii_nway_lp_ability_reg); + if (ret_val) + goto out; + /* Two bits in the Auto Negotiation Advertisement Register + * (Address 4) and two bits in the Auto Negotiation Base + * Page Ability Register (Address 5) determine flow control + * for both the PHY and the link partner. The following + * table, taken out of the IEEE 802.3ab/D6.0 dated March 25, + * 1999, describes these PAUSE resolution bits and how flow + * control is determined based upon these settings. + * NOTE: DC = Don't Care + * + * LOCAL DEVICE | LINK PARTNER + * PAUSE | ASM_DIR | PAUSE | ASM_DIR | NIC Resolution + *-------|---------|-------|---------|-------------------- + * 0 | 0 | DC | DC | igc_fc_none + * 0 | 1 | 0 | DC | igc_fc_none + * 0 | 1 | 1 | 0 | igc_fc_none + * 0 | 1 | 1 | 1 | igc_fc_tx_pause + * 1 | 0 | 0 | DC | igc_fc_none + * 1 | DC | 1 | DC | igc_fc_full + * 1 | 1 | 0 | 0 | igc_fc_none + * 1 | 1 | 0 | 1 | igc_fc_rx_pause + * + * Are both PAUSE bits set to 1? If so, this implies + * Symmetric Flow Control is enabled at both ends. The + * ASM_DIR bits are irrelevant per the spec. + * + * For Symmetric Flow Control: + * + * LOCAL DEVICE | LINK PARTNER + * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result + *-------|---------|-------|---------|-------------------- + * 1 | DC | 1 | DC | IGC_fc_full + * + */ + if ((mii_nway_adv_reg & NWAY_AR_PAUSE) && + (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE)) { + /* Now we need to check if the user selected RX ONLY + * of pause frames. In this case, we had to advertise + * FULL flow control because we could not advertise RX + * ONLY. Hence, we must now check to see if we need to + * turn OFF the TRANSMISSION of PAUSE frames. + */ + if (hw->fc.requested_mode == igc_fc_full) { + hw->fc.current_mode = igc_fc_full; + hw_dbg("Flow Control = FULL.\n"); + } else { + hw->fc.current_mode = igc_fc_rx_pause; + hw_dbg("Flow Control = RX PAUSE frames only.\n"); + } + } + + /* For receiving PAUSE frames ONLY. + * + * LOCAL DEVICE | LINK PARTNER + * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result + *-------|---------|-------|---------|-------------------- + * 0 | 1 | 1 | 1 | igc_fc_tx_pause + */ + else if (!(mii_nway_adv_reg & NWAY_AR_PAUSE) && + (mii_nway_adv_reg & NWAY_AR_ASM_DIR) && + (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) && + (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) { + hw->fc.current_mode = igc_fc_tx_pause; + hw_dbg("Flow Control = TX PAUSE frames only.\n"); + } + /* For transmitting PAUSE frames ONLY. + * + * LOCAL DEVICE | LINK PARTNER + * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result + *-------|---------|-------|---------|-------------------- + * 1 | 1 | 0 | 1 | igc_fc_rx_pause + */ + else if ((mii_nway_adv_reg & NWAY_AR_PAUSE) && + (mii_nway_adv_reg & NWAY_AR_ASM_DIR) && + !(mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) && + (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) { + hw->fc.current_mode = igc_fc_rx_pause; + hw_dbg("Flow Control = RX PAUSE frames only.\n"); + } + /* Per the IEEE spec, at this point flow control should be + * disabled. However, we want to consider that we could + * be connected to a legacy switch that doesn't advertise + * desired flow control, but can be forced on the link + * partner. So if we advertised no flow control, that is + * what we will resolve to. If we advertised some kind of + * receive capability (Rx Pause Only or Full Flow Control) + * and the link partner advertised none, we will configure + * ourselves to enable Rx Flow Control only. We can do + * this safely for two reasons: If the link partner really + * didn't want flow control enabled, and we enable Rx, no + * harm done since we won't be receiving any PAUSE frames + * anyway. If the intent on the link partner was to have + * flow control enabled, then by us enabling RX only, we + * can at least receive pause frames and process them. + * This is a good idea because in most cases, since we are + * predominantly a server NIC, more times than not we will + * be asked to delay transmission of packets than asking + * our link partner to pause transmission of frames. + */ + else if ((hw->fc.requested_mode == igc_fc_none) || + (hw->fc.requested_mode == igc_fc_tx_pause) || + (hw->fc.strict_ieee)) { + hw->fc.current_mode = igc_fc_none; + hw_dbg("Flow Control = NONE.\n"); + } else { + hw->fc.current_mode = igc_fc_rx_pause; + hw_dbg("Flow Control = RX PAUSE frames only.\n"); + } + + /* Now we need to do one last check... If we auto- + * negotiated to HALF DUPLEX, flow control should not be + * enabled per IEEE 802.3 spec. + */ + ret_val = hw->mac.ops.get_speed_and_duplex(hw, &speed, &duplex); + if (ret_val) { + hw_dbg("Error getting link speed and duplex\n"); + goto out; + } + + if (duplex == HALF_DUPLEX) + hw->fc.current_mode = igc_fc_none; + + /* Now we call a subroutine to actually force the MAC + * controller to use the correct flow control settings. + */ + ret_val = igc_force_mac_fc(hw); + if (ret_val) { + hw_dbg("Error forcing flow control settings\n"); + goto out; + } + } + +out: + return 0; +} + +/** + * igc_get_auto_rd_done - Check for auto read completion + * @hw: pointer to the HW structure + * + * Check EEPROM for Auto Read done bit. + */ +s32 igc_get_auto_rd_done(struct igc_hw *hw) +{ + s32 ret_val = 0; + s32 i = 0; + + while (i < AUTO_READ_DONE_TIMEOUT) { + if (rd32(IGC_EECD) & IGC_EECD_AUTO_RD) + break; + usleep_range(1000, 2000); + i++; + } + + if (i == AUTO_READ_DONE_TIMEOUT) { + hw_dbg("Auto read by HW from NVM has not completed.\n"); + ret_val = -IGC_ERR_RESET; + goto out; + } + +out: + return ret_val; +} + +/** + * igc_get_speed_and_duplex_copper - Retrieve current speed/duplex + * @hw: pointer to the HW structure + * @speed: stores the current speed + * @duplex: stores the current duplex + * + * Read the status register for the current speed/duplex and store the current + * speed and duplex for copper connections. + */ +s32 igc_get_speed_and_duplex_copper(struct igc_hw *hw, u16 *speed, + u16 *duplex) +{ + u32 status; + + status = rd32(IGC_STATUS); + if (status & IGC_STATUS_SPEED_1000) { + /* For I225, STATUS will indicate 1G speed in both 1 Gbps + * and 2.5 Gbps link modes. An additional bit is used + * to differentiate between 1 Gbps and 2.5 Gbps. + */ + if (hw->mac.type == igc_i225 && + (status & IGC_STATUS_SPEED_2500)) { + *speed = SPEED_2500; + hw_dbg("2500 Mbs, "); + } else { + *speed = SPEED_1000; + hw_dbg("1000 Mbs, "); + } + } else if (status & IGC_STATUS_SPEED_100) { + *speed = SPEED_100; + hw_dbg("100 Mbs, "); + } else { + *speed = SPEED_10; + hw_dbg("10 Mbs, "); + } + + if (status & IGC_STATUS_FD) { + *duplex = FULL_DUPLEX; + hw_dbg("Full Duplex\n"); + } else { + *duplex = HALF_DUPLEX; + hw_dbg("Half Duplex\n"); + } + + return 0; +} + +/** + * igc_put_hw_semaphore - Release hardware semaphore + * @hw: pointer to the HW structure + * + * Release hardware semaphore used to access the PHY or NVM + */ +void igc_put_hw_semaphore(struct igc_hw *hw) +{ + u32 swsm; + + swsm = rd32(IGC_SWSM); + + swsm &= ~(IGC_SWSM_SMBI | IGC_SWSM_SWESMBI); + + wr32(IGC_SWSM, swsm); +} + +/** + * igc_enable_mng_pass_thru - Enable processing of ARP's + * @hw: pointer to the HW structure + * + * Verifies the hardware needs to leave interface enabled so that frames can + * be directed to and from the management interface. + */ +bool igc_enable_mng_pass_thru(struct igc_hw *hw) +{ + bool ret_val = false; + u32 fwsm, factps; + u32 manc; + + if (!hw->mac.asf_firmware_present) + goto out; + + manc = rd32(IGC_MANC); + + if (!(manc & IGC_MANC_RCV_TCO_EN)) + goto out; + + if (hw->mac.arc_subsystem_valid) { + fwsm = rd32(IGC_FWSM); + factps = rd32(IGC_FACTPS); + + if (!(factps & IGC_FACTPS_MNGCG) && + ((fwsm & IGC_FWSM_MODE_MASK) == + (igc_mng_mode_pt << IGC_FWSM_MODE_SHIFT))) { + ret_val = true; + goto out; + } + } else { + if ((manc & IGC_MANC_SMBUS_EN) && + !(manc & IGC_MANC_ASF_EN)) { + ret_val = true; + goto out; + } + } + +out: + return ret_val; +} |