1 files changed, 103 insertions, 3 deletions

diff --git a/drivers/net/dsa/microchip/ksz9477.c b/drivers/net/dsa/microchip/ksz9477.c
index cde8ef33d029..2534c3d122e4 100644
--- a/drivers/net/dsa/microchip/ksz9477.c
+++ b/drivers/net/dsa/microchip/ksz9477.c
@@ -56,6 +56,103 @@ int ksz9477_change_mtu(struct ksz_device *dev, int port, int mtu)
 				  REG_SW_MTU_MASK, frame_size);
 }
 
+/**
+ * ksz9477_handle_wake_reason - Handle wake reason on a specified port.
+ * @dev: The device structure.
+ * @port: The port number.
+ *
+ * This function reads the PME (Power Management Event) status register of a
+ * specified port to determine the wake reason. If there is no wake event, it
+ * returns early. Otherwise, it logs the wake reason which could be due to a
+ * "Magic Packet", "Link Up", or "Energy Detect" event. The PME status register
+ * is then cleared to acknowledge the handling of the wake event.
+ *
+ * Return: 0 on success, or an error code on failure.
+ */
+static int ksz9477_handle_wake_reason(struct ksz_device *dev, int port)
+{
+	u8 pme_status;
+	int ret;
+
+	ret = ksz_pread8(dev, port, REG_PORT_PME_STATUS, &pme_status);
+	if (ret)
+		return ret;
+
+	if (!pme_status)
+		return 0;
+
+	dev_dbg(dev->dev, "Wake event on port %d due to:%s%s\n", port,
+		pme_status & PME_WOL_LINKUP ? " \"Link Up\"" : "",
+		pme_status & PME_WOL_ENERGY ? " \"Enery detect\"" : "");
+
+	return ksz_pwrite8(dev, port, REG_PORT_PME_STATUS, pme_status);
+}
+
+/**
+ * ksz9477_get_wol - Get Wake-on-LAN settings for a specified port.
+ * @dev: The device structure.
+ * @port: The port number.
+ * @wol: Pointer to ethtool Wake-on-LAN settings structure.
+ *
+ * This function checks the PME Pin Control Register to see if  PME Pin Output
+ * Enable is set, indicating PME is enabled. If enabled, it sets the supported
+ * and active WoL flags.
+ */
+void ksz9477_get_wol(struct ksz_device *dev, int port,
+		     struct ethtool_wolinfo *wol)
+{
+	u8 pme_ctrl;
+	int ret;
+
+	if (!dev->wakeup_source)
+		return;
+
+	wol->supported = WAKE_PHY;
+
+	ret = ksz_pread8(dev, port, REG_PORT_PME_CTRL, &pme_ctrl);
+	if (ret)
+		return;
+
+	if (pme_ctrl & (PME_WOL_LINKUP | PME_WOL_ENERGY))
+		wol->wolopts |= WAKE_PHY;
+}
+
+/**
+ * ksz9477_set_wol - Set Wake-on-LAN settings for a specified port.
+ * @dev: The device structure.
+ * @port: The port number.
+ * @wol: Pointer to ethtool Wake-on-LAN settings structure.
+ *
+ * This function configures Wake-on-LAN (WoL) settings for a specified port.
+ * It validates the provided WoL options, checks if PME is enabled via the
+ * switch's PME Pin Control Register, clears any previous wake reasons,
+ * and sets the Magic Packet flag in the port's PME control register if
+ * specified.
+ *
+ * Return: 0 on success, or other error codes on failure.
+ */
+int ksz9477_set_wol(struct ksz_device *dev, int port,
+		    struct ethtool_wolinfo *wol)
+{
+	u8 pme_ctrl = 0;
+	int ret;
+
+	if (wol->wolopts & ~WAKE_PHY)
+		return -EINVAL;
+
+	if (!dev->wakeup_source)
+		return -EOPNOTSUPP;
+
+	ret = ksz9477_handle_wake_reason(dev, port);
+	if (ret)
+		return ret;
+
+	if (wol->wolopts & WAKE_PHY)
+		pme_ctrl |= PME_WOL_LINKUP | PME_WOL_ENERGY;
+
+	return ksz_pwrite8(dev, port, REG_PORT_PME_CTRL, pme_ctrl);
+}
+
 static int ksz9477_wait_vlan_ctrl_ready(struct ksz_device *dev)
 {
 	unsigned int val;
@@ -1006,6 +1103,9 @@ void ksz9477_port_setup(struct ksz_device *dev, int port, bool cpu_port)
 		ksz_pread16(dev, port, REG_PORT_PHY_INT_ENABLE, &data16);
 
 	ksz9477_port_acl_init(dev, port);
+
+	/* clear pending wake flags */
+	ksz9477_handle_wake_reason(dev, port);
 }
 
 void ksz9477_config_cpu_port(struct dsa_switch *ds)
@@ -1170,7 +1270,7 @@ int ksz9477_tc_cbs_set_cinc(struct ksz_device *dev, int port, u32 val)
 void ksz9477_hsr_join(struct dsa_switch *ds, int port, struct net_device *hsr)
 {
 	struct ksz_device *dev = ds->priv;
-	struct net_device *slave;
+	struct net_device *user;
 	struct dsa_port *hsr_dp;
 	u8 data, hsr_ports = 0;
 
@@ -1202,8 +1302,8 @@ void ksz9477_hsr_join(struct dsa_switch *ds, int port, struct net_device *hsr)
 	ksz_port_cfg(dev, port, REG_PORT_LUE_CTRL, PORT_SRC_ADDR_FILTER, true);
 
 	/* Setup HW supported features for lan HSR ports */
-	slave = dsa_to_port(ds, port)->slave;
-	slave->features |= KSZ9477_SUPPORTED_HSR_FEATURES;
+	user = dsa_to_port(ds, port)->user;
+	user->features |= KSZ9477_SUPPORTED_HSR_FEATURES;
 }
 
 void ksz9477_hsr_leave(struct dsa_switch *ds, int port, struct net_device *hsr)