diff options
Diffstat (limited to 'drivers/net/Kconfig')
| -rw-r--r-- | drivers/net/Kconfig | 82 |
1 files changed, 51 insertions, 31 deletions
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig index f4182cfffe9d..84925915dce4 100644 --- a/drivers/net/Kconfig +++ b/drivers/net/Kconfig @@ -524,6 +524,18 @@ config STNIC If unsure, say N. +config SH_ETH + tristate "Renesas SuperH Ethernet support" + depends on SUPERH && \ + (CPU_SUBTYPE_SH7710 || CPU_SUBTYPE_SH7712) + select CRC32 + select MII + select MDIO_BITBANG + select PHYLIB + help + Renesas SuperH Ethernet device driver. + This driver support SH7710 and SH7712. + config SUNLANCE tristate "Sun LANCE support" depends on SBUS @@ -926,6 +938,23 @@ config DM9000 To compile this driver as a module, choose M here. The module will be called dm9000. +config DM9000_DEBUGLEVEL + int "DM9000 maximum debug level" + depends on DM9000 + default 4 + help + The maximum level of debugging code compiled into the DM9000 + driver. + +config DM9000_FORCE_SIMPLE_PHY_POLL + bool "Force simple NSR based PHY polling" + depends on DM9000 + ---help--- + This configuration forces the DM9000 to use the NSR's LinkStatus + bit to determine if the link is up or down instead of the more + costly MII PHY reads. Note, this will not work if the chip is + operating with an external PHY. + config ENC28J60 tristate "ENC28J60 support" depends on EXPERIMENTAL && SPI && NET_ETHERNET @@ -943,19 +972,11 @@ config ENC28J60_WRITEVERIFY Enable the verify after the buffer write useful for debugging purpose. If unsure, say N. -config DM9000_DEBUGLEVEL - int "DM9000 maximum debug level" - depends on DM9000 - default 4 - help - The maximum level of debugging code compiled into the DM9000 - driver. - config SMC911X tristate "SMSC LAN911[5678] support" select CRC32 select MII - depends on ARCH_PXA || SH_MAGIC_PANEL_R2 + depends on ARCH_PXA || SUPERH help This is a driver for SMSC's LAN911x series of Ethernet chipsets including the new LAN9115, LAN9116, LAN9117, and LAN9118. @@ -1243,7 +1264,6 @@ config IBMVETH To compile this driver as a module, choose M here. The module will be called ibmveth. -source "drivers/net/ibm_emac/Kconfig" source "drivers/net/ibm_newemac/Kconfig" config NET_PCI @@ -1670,7 +1690,7 @@ config SUNDANCE_MMIO config TLAN tristate "TI ThunderLAN support" - depends on NET_PCI && (PCI || EISA) && !64BIT + depends on NET_PCI && (PCI || EISA) ---help--- If you have a PCI Ethernet network card based on the ThunderLAN chip which is supported by this driver, say Y and read the @@ -2014,9 +2034,6 @@ config E1000E To compile this driver as a module, choose M here. The module will be called e1000e. -config E1000E_ENABLED - def_bool E1000E != n - config IP1000 tristate "IP1000 Gigabit Ethernet support" depends on PCI && EXPERIMENTAL @@ -2105,27 +2122,13 @@ config R8169 To compile this driver as a module, choose M here: the module will be called r8169. This is recommended. -config R8169_NAPI - bool "Use Rx Polling (NAPI) (EXPERIMENTAL)" - depends on R8169 && EXPERIMENTAL - help - NAPI is a new driver API designed to reduce CPU and interrupt load - when the driver is receiving lots of packets from the card. It is - still somewhat experimental and thus not yet enabled by default. - - If your estimated Rx load is 10kpps or more, or if the card will be - deployed on potentially unfriendly networks (e.g. in a firewall), - then say Y here. - - If in doubt, say N. - config R8169_VLAN bool "VLAN support" depends on R8169 && VLAN_8021Q ---help--- Say Y here for the r8169 driver to support the functions required by the kernel 802.1Q code. - + If in doubt, say Y. config SB1250_MAC @@ -2228,6 +2231,7 @@ config VIA_VELOCITY config TIGON3 tristate "Broadcom Tigon3 support" depends on PCI + select PHYLIB help This driver supports Broadcom Tigon3 based gigabit Ethernet cards. @@ -2283,6 +2287,19 @@ config GELIC_WIRELESS the driver automatically distinguishes the models, you can safely enable this option even if you have a wireless-less model. +config GELIC_WIRELESS_OLD_PSK_INTERFACE + bool "PS3 Wireless private PSK interface (OBSOLETE)" + depends on GELIC_WIRELESS + help + This option retains the obsolete private interface to pass + the PSK from user space programs to the driver. The PSK + stands for 'Pre Shared Key' and is used for WPA[2]-PSK + (WPA-Personal) environment. + If WPA[2]-PSK is used and you need to use old programs that + support only this old interface, say Y. Otherwise N. + + If unsure, say N. + config GIANFAR tristate "Gianfar Ethernet" depends on FSL_SOC @@ -2407,8 +2424,9 @@ config CHELSIO_T1_NAPI config CHELSIO_T3 tristate "Chelsio Communications T3 10Gb Ethernet support" - depends on PCI + depends on PCI && INET select FW_LOADER + select INET_LRO help This driver supports Chelsio T3-based gigabit and 10Gb Ethernet adapters. @@ -2436,7 +2454,8 @@ config EHEA config IXGBE tristate "Intel(R) 10GbE PCI Express adapters support" - depends on PCI + depends on PCI && INET + select INET_LRO ---help--- This driver supports Intel(R) 10GbE PCI Express family of adapters. For more information on how to identify your adapter, go @@ -2574,6 +2593,7 @@ config BNX2X tristate "Broadcom NetXtremeII 10Gb support" depends on PCI select ZLIB_INFLATE + select LIBCRC32C help This driver supports Broadcom NetXtremeII 10 gigabit Ethernet cards. To compile this driver as a module, choose M here: the module |