aboutsummaryrefslogtreecommitdiff
path: root/drivers/mmc
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/mmc')
-rw-r--r--drivers/mmc/card/block.c2
-rw-r--r--drivers/mmc/card/sdio_uart.c10
-rw-r--r--drivers/mmc/core/core.c3
-rw-r--r--drivers/mmc/core/host.c4
-rw-r--r--drivers/mmc/core/mmc.c3
-rw-r--r--drivers/mmc/core/sd.c8
-rw-r--r--drivers/mmc/core/sdio.c8
-rw-r--r--drivers/mmc/host/atmel-mci.c21
-rw-r--r--drivers/mmc/host/mmci.c187
-rw-r--r--drivers/mmc/host/mmci.h15
-rw-r--r--drivers/mmc/host/s3cmci.c4
-rw-r--r--drivers/mmc/host/sdhci-esdhc-imx.c5
-rw-r--r--drivers/mmc/host/sh_mmcif.c5
-rw-r--r--drivers/mmc/host/tmio_mmc_pio.c5
14 files changed, 178 insertions, 102 deletions
diff --git a/drivers/mmc/card/block.c b/drivers/mmc/card/block.c
index c6a383d0244d..e5a3c7b6dedb 100644
--- a/drivers/mmc/card/block.c
+++ b/drivers/mmc/card/block.c
@@ -1685,7 +1685,7 @@ static int mmc_add_disk(struct mmc_blk_data *md)
if ((md->area_type & MMC_BLK_DATA_AREA_BOOT) &&
card->ext_csd.boot_ro_lockable) {
- mode_t mode;
+ umode_t mode;
if (card->ext_csd.boot_ro_lock & EXT_CSD_BOOT_WP_B_PWR_WP_DIS)
mode = S_IRUGO;
diff --git a/drivers/mmc/card/sdio_uart.c b/drivers/mmc/card/sdio_uart.c
index 2c151e18c9e8..5a2cbfac66d2 100644
--- a/drivers/mmc/card/sdio_uart.c
+++ b/drivers/mmc/card/sdio_uart.c
@@ -750,15 +750,12 @@ static int sdio_uart_install(struct tty_driver *driver, struct tty_struct *tty)
{
int idx = tty->index;
struct sdio_uart_port *port = sdio_uart_port_get(idx);
- int ret = tty_init_termios(tty);
+ int ret = tty_standard_install(driver, tty);
- if (ret == 0) {
- tty_driver_kref_get(driver);
- tty->count++;
+ if (ret == 0)
/* This is the ref sdio_uart_port get provided */
tty->driver_data = port;
- driver->ttys[idx] = tty;
- } else
+ else
sdio_uart_port_put(port);
return ret;
}
@@ -1178,7 +1175,6 @@ static int __init sdio_uart_init(void)
if (!tty_drv)
return -ENOMEM;
- tty_drv->owner = THIS_MODULE;
tty_drv->driver_name = "sdio_uart";
tty_drv->name = "ttySDIO";
tty_drv->major = 0; /* dynamically allocated */
diff --git a/drivers/mmc/core/core.c b/drivers/mmc/core/core.c
index 690255c7d4dc..132378b89d76 100644
--- a/drivers/mmc/core/core.c
+++ b/drivers/mmc/core/core.c
@@ -2068,6 +2068,9 @@ static int mmc_rescan_try_freq(struct mmc_host *host, unsigned freq)
*/
mmc_hw_reset_for_init(host);
+ /* Initialization should be done at 3.3 V I/O voltage. */
+ mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_330, 0);
+
/*
* sdio_reset sends CMD52 to reset card. Since we do not know
* if the card is being re-initialized, just send it. CMD52
diff --git a/drivers/mmc/core/host.c b/drivers/mmc/core/host.c
index 30055f2b0d44..c3704e293a7b 100644
--- a/drivers/mmc/core/host.c
+++ b/drivers/mmc/core/host.c
@@ -238,10 +238,10 @@ static inline void mmc_host_clk_init(struct mmc_host *host)
/* Hold MCI clock for 8 cycles by default */
host->clk_delay = 8;
/*
- * Default clock gating delay is 200ms.
+ * Default clock gating delay is 0ms to avoid wasting power.
* This value can be tuned by writing into sysfs entry.
*/
- host->clkgate_delay = 200;
+ host->clkgate_delay = 0;
host->clk_gated = false;
INIT_DELAYED_WORK(&host->clk_gate_work, mmc_host_clk_gate_work);
spin_lock_init(&host->clk_lock);
diff --git a/drivers/mmc/core/mmc.c b/drivers/mmc/core/mmc.c
index a48066344fa8..2b9ed1401dc4 100644
--- a/drivers/mmc/core/mmc.c
+++ b/drivers/mmc/core/mmc.c
@@ -816,6 +816,9 @@ static int mmc_init_card(struct mmc_host *host, u32 ocr,
if (!mmc_host_is_spi(host))
mmc_set_bus_mode(host, MMC_BUSMODE_OPENDRAIN);
+ /* Initialization should be done at 3.3 V I/O voltage. */
+ mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_330, 0);
+
/*
* Since we're changing the OCR value, we seem to
* need to tell some cards to go back to the idle
diff --git a/drivers/mmc/core/sd.c b/drivers/mmc/core/sd.c
index 5017f9354ce2..c272c6868ecf 100644
--- a/drivers/mmc/core/sd.c
+++ b/drivers/mmc/core/sd.c
@@ -911,6 +911,9 @@ static int mmc_sd_init_card(struct mmc_host *host, u32 ocr,
BUG_ON(!host);
WARN_ON(!host->claimed);
+ /* The initialization should be done at 3.3 V I/O voltage. */
+ mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_330, 0);
+
err = mmc_sd_get_cid(host, ocr, cid, &rocr);
if (err)
return err;
@@ -1156,11 +1159,6 @@ int mmc_attach_sd(struct mmc_host *host)
BUG_ON(!host);
WARN_ON(!host->claimed);
- /* Make sure we are at 3.3V signalling voltage */
- err = mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_330, false);
- if (err)
- return err;
-
/* Disable preset value enable if already set since last time */
if (host->ops->enable_preset_value) {
mmc_host_clk_hold(host);
diff --git a/drivers/mmc/core/sdio.c b/drivers/mmc/core/sdio.c
index 12cde6ee17f5..2c7c83f832d2 100644
--- a/drivers/mmc/core/sdio.c
+++ b/drivers/mmc/core/sdio.c
@@ -585,6 +585,9 @@ static int mmc_sdio_init_card(struct mmc_host *host, u32 ocr,
* Inform the card of the voltage
*/
if (!powered_resume) {
+ /* The initialization should be done at 3.3 V I/O voltage. */
+ mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_330, 0);
+
err = mmc_send_io_op_cond(host, host->ocr, &ocr);
if (err)
goto err;
@@ -996,6 +999,11 @@ static int mmc_sdio_power_restore(struct mmc_host *host)
* With these steps taken, mmc_select_voltage() is also required to
* restore the correct voltage setting of the card.
*/
+
+ /* The initialization should be done at 3.3 V I/O voltage. */
+ if (!mmc_card_keep_power(host))
+ mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_330, 0);
+
sdio_reset(host);
mmc_go_idle(host);
mmc_send_if_cond(host, host->ocr_avail);
diff --git a/drivers/mmc/host/atmel-mci.c b/drivers/mmc/host/atmel-mci.c
index 6985cdb0bb26..e4449a54ae8f 100644
--- a/drivers/mmc/host/atmel-mci.c
+++ b/drivers/mmc/host/atmel-mci.c
@@ -1948,12 +1948,12 @@ static bool atmci_filter(struct dma_chan *chan, void *slave)
}
}
-static void atmci_configure_dma(struct atmel_mci *host)
+static bool atmci_configure_dma(struct atmel_mci *host)
{
struct mci_platform_data *pdata;
if (host == NULL)
- return;
+ return false;
pdata = host->pdev->dev.platform_data;
@@ -1970,12 +1970,15 @@ static void atmci_configure_dma(struct atmel_mci *host)
host->dma.chan =
dma_request_channel(mask, atmci_filter, pdata->dma_slave);
}
- if (!host->dma.chan)
- dev_notice(&host->pdev->dev, "DMA not available, using PIO\n");
- else
+ if (!host->dma.chan) {
+ dev_warn(&host->pdev->dev, "no DMA channel available\n");
+ return false;
+ } else {
dev_info(&host->pdev->dev,
"Using %s for DMA transfers\n",
dma_chan_name(host->dma.chan));
+ return true;
+ }
}
static inline unsigned int atmci_get_version(struct atmel_mci *host)
@@ -2085,8 +2088,7 @@ static int __init atmci_probe(struct platform_device *pdev)
/* Get MCI capabilities and set operations according to it */
atmci_get_cap(host);
- if (host->caps.has_dma) {
- dev_info(&pdev->dev, "using DMA\n");
+ if (host->caps.has_dma && atmci_configure_dma(host)) {
host->prepare_data = &atmci_prepare_data_dma;
host->submit_data = &atmci_submit_data_dma;
host->stop_transfer = &atmci_stop_transfer_dma;
@@ -2096,15 +2098,12 @@ static int __init atmci_probe(struct platform_device *pdev)
host->submit_data = &atmci_submit_data_pdc;
host->stop_transfer = &atmci_stop_transfer_pdc;
} else {
- dev_info(&pdev->dev, "no DMA, no PDC\n");
+ dev_info(&pdev->dev, "using PIO\n");
host->prepare_data = &atmci_prepare_data;
host->submit_data = &atmci_submit_data;
host->stop_transfer = &atmci_stop_transfer;
}
- if (host->caps.has_dma)
- atmci_configure_dma(host);
-
platform_set_drvdata(pdev, host);
/* We need at least one slot to succeed */
diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index 0d955ffaf44e..983e244eca76 100644
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -53,6 +53,8 @@ static unsigned int fmax = 515633;
* @sdio: variant supports SDIO
* @st_clkdiv: true if using a ST-specific clock divider algorithm
* @blksz_datactrl16: true if Block size is at b16..b30 position in datactrl register
+ * @pwrreg_powerup: power up value for MMCIPOWER register
+ * @signal_direction: input/out direction of bus signals can be indicated
*/
struct variant_data {
unsigned int clkreg;
@@ -63,18 +65,22 @@ struct variant_data {
bool sdio;
bool st_clkdiv;
bool blksz_datactrl16;
+ u32 pwrreg_powerup;
+ bool signal_direction;
};
static struct variant_data variant_arm = {
.fifosize = 16 * 4,
.fifohalfsize = 8 * 4,
.datalength_bits = 16,
+ .pwrreg_powerup = MCI_PWR_UP,
};
static struct variant_data variant_arm_extended_fifo = {
.fifosize = 128 * 4,
.fifohalfsize = 64 * 4,
.datalength_bits = 16,
+ .pwrreg_powerup = MCI_PWR_UP,
};
static struct variant_data variant_u300 = {
@@ -83,6 +89,8 @@ static struct variant_data variant_u300 = {
.clkreg_enable = MCI_ST_U300_HWFCEN,
.datalength_bits = 16,
.sdio = true,
+ .pwrreg_powerup = MCI_PWR_ON,
+ .signal_direction = true,
};
static struct variant_data variant_ux500 = {
@@ -93,6 +101,8 @@ static struct variant_data variant_ux500 = {
.datalength_bits = 24,
.sdio = true,
.st_clkdiv = true,
+ .pwrreg_powerup = MCI_PWR_ON,
+ .signal_direction = true,
};
static struct variant_data variant_ux500v2 = {
@@ -104,11 +114,35 @@ static struct variant_data variant_ux500v2 = {
.sdio = true,
.st_clkdiv = true,
.blksz_datactrl16 = true,
+ .pwrreg_powerup = MCI_PWR_ON,
+ .signal_direction = true,
};
/*
* This must be called with host->lock held
*/
+static void mmci_write_clkreg(struct mmci_host *host, u32 clk)
+{
+ if (host->clk_reg != clk) {
+ host->clk_reg = clk;
+ writel(clk, host->base + MMCICLOCK);
+ }
+}
+
+/*
+ * This must be called with host->lock held
+ */
+static void mmci_write_pwrreg(struct mmci_host *host, u32 pwr)
+{
+ if (host->pwr_reg != pwr) {
+ host->pwr_reg = pwr;
+ writel(pwr, host->base + MMCIPOWER);
+ }
+}
+
+/*
+ * This must be called with host->lock held
+ */
static void mmci_set_clkreg(struct mmci_host *host, unsigned int desired)
{
struct variant_data *variant = host->variant;
@@ -153,7 +187,7 @@ static void mmci_set_clkreg(struct mmci_host *host, unsigned int desired)
if (host->mmc->ios.bus_width == MMC_BUS_WIDTH_8)
clk |= MCI_ST_8BIT_BUS;
- writel(clk, host->base + MMCICLOCK);
+ mmci_write_clkreg(host, clk);
}
static void
@@ -166,14 +200,10 @@ mmci_request_end(struct mmci_host *host, struct mmc_request *mrq)
host->mrq = NULL;
host->cmd = NULL;
- /*
- * Need to drop the host lock here; mmc_request_done may call
- * back into the driver...
- */
- spin_unlock(&host->lock);
- pm_runtime_put(mmc_dev(host->mmc));
mmc_request_done(host->mmc, mrq);
- spin_lock(&host->lock);
+
+ pm_runtime_mark_last_busy(mmc_dev(host->mmc));
+ pm_runtime_put_autosuspend(mmc_dev(host->mmc));
}
static void mmci_set_mask1(struct mmci_host *host, unsigned int mask)
@@ -607,6 +637,11 @@ static void mmci_start_data(struct mmci_host *host, struct mmc_data *data)
if (data->flags & MMC_DATA_READ)
datactrl |= MCI_DPSM_DIRECTION;
+ /* The ST Micro variants has a special bit to enable SDIO */
+ if (variant->sdio && host->mmc->card)
+ if (mmc_card_sdio(host->mmc->card))
+ datactrl |= MCI_ST_DPSM_SDIOEN;
+
/*
* Attempt to use DMA operation mode, if this
* should fail, fall back to PIO mode
@@ -635,11 +670,6 @@ static void mmci_start_data(struct mmci_host *host, struct mmc_data *data)
irqmask = MCI_TXFIFOHALFEMPTYMASK;
}
- /* The ST Micro variants has a special bit to enable SDIO */
- if (variant->sdio && host->mmc->card)
- if (mmc_card_sdio(host->mmc->card))
- datactrl |= MCI_ST_DPSM_SDIOEN;
-
writel(datactrl, base + MMCIDATACTRL);
writel(readl(base + MMCIMASK0) & ~MCI_DATAENDMASK, base + MMCIMASK0);
mmci_set_mask1(host, irqmask);
@@ -786,7 +816,24 @@ static int mmci_pio_read(struct mmci_host *host, char *buffer, unsigned int rema
if (count <= 0)
break;
- readsl(base + MMCIFIFO, ptr, count >> 2);
+ /*
+ * SDIO especially may want to send something that is
+ * not divisible by 4 (as opposed to card sectors
+ * etc). Therefore make sure to always read the last bytes
+ * while only doing full 32-bit reads towards the FIFO.
+ */
+ if (unlikely(count & 0x3)) {
+ if (count < 4) {
+ unsigned char buf[4];
+ readsl(base + MMCIFIFO, buf, 1);
+ memcpy(ptr, buf, count);
+ } else {
+ readsl(base + MMCIFIFO, ptr, count >> 2);
+ count &= ~0x3;
+ }
+ } else {
+ readsl(base + MMCIFIFO, ptr, count >> 2);
+ }
ptr += count;
remain -= count;
@@ -821,14 +868,13 @@ static int mmci_pio_write(struct mmci_host *host, char *buffer, unsigned int rem
*/
if (variant->sdio &&
mmc_card_sdio(host->mmc->card)) {
+ u32 clk;
if (count < 8)
- writel(readl(host->base + MMCICLOCK) &
- ~variant->clkreg_enable,
- host->base + MMCICLOCK);
+ clk = host->clk_reg & ~variant->clkreg_enable;
else
- writel(readl(host->base + MMCICLOCK) |
- variant->clkreg_enable,
- host->base + MMCICLOCK);
+ clk = host->clk_reg | variant->clkreg_enable;
+
+ mmci_write_clkreg(host, clk);
}
/*
@@ -1015,10 +1061,17 @@ static void mmci_request(struct mmc_host *mmc, struct mmc_request *mrq)
static void mmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
{
struct mmci_host *host = mmc_priv(mmc);
+ struct variant_data *variant = host->variant;
u32 pwr = 0;
unsigned long flags;
int ret;
+ pm_runtime_get_sync(mmc_dev(mmc));
+
+ if (host->plat->ios_handler &&
+ host->plat->ios_handler(mmc_dev(mmc), ios))
+ dev_err(mmc_dev(mmc), "platform ios_handler failed\n");
+
switch (ios->power_mode) {
case MMC_POWER_OFF:
if (host->vcc)
@@ -1035,22 +1088,38 @@ static void mmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
* power should be rare so we print an error
* and return here.
*/
- return;
+ goto out;
}
}
- if (host->plat->vdd_handler)
- pwr |= host->plat->vdd_handler(mmc_dev(mmc), ios->vdd,
- ios->power_mode);
- /* The ST version does not have this, fall through to POWER_ON */
- if (host->hw_designer != AMBA_VENDOR_ST) {
- pwr |= MCI_PWR_UP;
- break;
- }
+ /*
+ * The ST Micro variant doesn't have the PL180s MCI_PWR_UP
+ * and instead uses MCI_PWR_ON so apply whatever value is
+ * configured in the variant data.
+ */
+ pwr |= variant->pwrreg_powerup;
+
+ break;
case MMC_POWER_ON:
pwr |= MCI_PWR_ON;
break;
}
+ if (variant->signal_direction && ios->power_mode != MMC_POWER_OFF) {
+ /*
+ * The ST Micro variant has some additional bits
+ * indicating signal direction for the signals in
+ * the SD/MMC bus and feedback-clock usage.
+ */
+ pwr |= host->plat->sigdir;
+
+ if (ios->bus_width == MMC_BUS_WIDTH_4)
+ pwr &= ~MCI_ST_DATA74DIREN;
+ else if (ios->bus_width == MMC_BUS_WIDTH_1)
+ pwr &= (~MCI_ST_DATA74DIREN &
+ ~MCI_ST_DATA31DIREN &
+ ~MCI_ST_DATA2DIREN);
+ }
+
if (ios->bus_mode == MMC_BUSMODE_OPENDRAIN) {
if (host->hw_designer != AMBA_VENDOR_ST)
pwr |= MCI_ROD;
@@ -1066,13 +1135,13 @@ static void mmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
spin_lock_irqsave(&host->lock, flags);
mmci_set_clkreg(host, ios->clock);
-
- if (host->pwr != pwr) {
- host->pwr = pwr;
- writel(pwr, host->base + MMCIPOWER);
- }
+ mmci_write_pwrreg(host, pwr);
spin_unlock_irqrestore(&host->lock, flags);
+
+ out:
+ pm_runtime_mark_last_busy(mmc_dev(mmc));
+ pm_runtime_put_autosuspend(mmc_dev(mmc));
}
static int mmci_get_ro(struct mmc_host *mmc)
@@ -1271,12 +1340,13 @@ static int __devinit mmci_probe(struct amba_device *dev,
/*
* Block size can be up to 2048 bytes, but must be a power of two.
*/
- mmc->max_blk_size = 2048;
+ mmc->max_blk_size = 1 << 11;
/*
- * No limit on the number of blocks transferred.
+ * Limit the number of blocks transferred so that we don't overflow
+ * the maximum request size.
*/
- mmc->max_blk_count = mmc->max_req_size;
+ mmc->max_blk_count = mmc->max_req_size >> 11;
spin_lock_init(&host->lock);
@@ -1325,7 +1395,7 @@ static int __devinit mmci_probe(struct amba_device *dev,
if (ret)
goto unmap;
- if (dev->irq[1] == NO_IRQ)
+ if (dev->irq[1] == NO_IRQ || !dev->irq[1])
host->singleirq = true;
else {
ret = request_irq(dev->irq[1], mmci_pio_irq, IRQF_SHARED,
@@ -1345,6 +1415,8 @@ static int __devinit mmci_probe(struct amba_device *dev,
mmci_dma_setup(host);
+ pm_runtime_set_autosuspend_delay(&dev->dev, 50);
+ pm_runtime_use_autosuspend(&dev->dev);
pm_runtime_put(&dev->dev);
mmc_add_host(mmc);
@@ -1429,43 +1501,49 @@ static int __devexit mmci_remove(struct amba_device *dev)
return 0;
}
-#ifdef CONFIG_PM
-static int mmci_suspend(struct amba_device *dev, pm_message_t state)
+#ifdef CONFIG_SUSPEND
+static int mmci_suspend(struct device *dev)
{
- struct mmc_host *mmc = amba_get_drvdata(dev);
+ struct amba_device *adev = to_amba_device(dev);
+ struct mmc_host *mmc = amba_get_drvdata(adev);
int ret = 0;
if (mmc) {
struct mmci_host *host = mmc_priv(mmc);
ret = mmc_suspend_host(mmc);
- if (ret == 0)
+ if (ret == 0) {
+ pm_runtime_get_sync(dev);
writel(0, host->base + MMCIMASK0);
+ }
}
return ret;
}
-static int mmci_resume(struct amba_device *dev)
+static int mmci_resume(struct device *dev)
{
- struct mmc_host *mmc = amba_get_drvdata(dev);
+ struct amba_device *adev = to_amba_device(dev);
+ struct mmc_host *mmc = amba_get_drvdata(adev);
int ret = 0;
if (mmc) {
struct mmci_host *host = mmc_priv(mmc);
writel(MCI_IRQENABLE, host->base + MMCIMASK0);
+ pm_runtime_put(dev);
ret = mmc_resume_host(mmc);
}
return ret;
}
-#else
-#define mmci_suspend NULL
-#define mmci_resume NULL
#endif
+static const struct dev_pm_ops mmci_dev_pm_ops = {
+ SET_SYSTEM_SLEEP_PM_OPS(mmci_suspend, mmci_resume)
+};
+
static struct amba_id mmci_ids[] = {
{
.id = 0x00041180,
@@ -1511,26 +1589,15 @@ MODULE_DEVICE_TABLE(amba, mmci_ids);
static struct amba_driver mmci_driver = {
.drv = {
.name = DRIVER_NAME,
+ .pm = &mmci_dev_pm_ops,
},
.probe = mmci_probe,
.remove = __devexit_p(mmci_remove),
- .suspend = mmci_suspend,
- .resume = mmci_resume,
.id_table = mmci_ids,
};
-static int __init mmci_init(void)
-{
- return amba_driver_register(&mmci_driver);
-}
-
-static void __exit mmci_exit(void)
-{
- amba_driver_unregister(&mmci_driver);
-}
+module_amba_driver(mmci_driver);
-module_init(mmci_init);
-module_exit(mmci_exit);
module_param(fmax, uint, 0444);
MODULE_DESCRIPTION("ARM PrimeCell PL180/181 Multimedia Card Interface driver");
diff --git a/drivers/mmc/host/mmci.h b/drivers/mmc/host/mmci.h
index 79e4143ab9df..d437ccf62d6b 100644
--- a/drivers/mmc/host/mmci.h
+++ b/drivers/mmc/host/mmci.h
@@ -13,16 +13,6 @@
#define MCI_PWR_ON 0x03
#define MCI_OD (1 << 6)
#define MCI_ROD (1 << 7)
-/*
- * The ST Micro version does not have ROD and reuse the voltage registers
- * for direction settings
- */
-#define MCI_ST_DATA2DIREN (1 << 2)
-#define MCI_ST_CMDDIREN (1 << 3)
-#define MCI_ST_DATA0DIREN (1 << 4)
-#define MCI_ST_DATA31DIREN (1 << 5)
-#define MCI_ST_FBCLKEN (1 << 7)
-#define MCI_ST_DATA74DIREN (1 << 8)
#define MMCICLOCK 0x004
#define MCI_CLK_ENABLE (1 << 8)
@@ -160,7 +150,7 @@
(MCI_RXFIFOHALFFULLMASK | MCI_RXDATAAVLBLMASK | \
MCI_TXFIFOHALFEMPTYMASK)
-#define NR_SG 16
+#define NR_SG 128
struct clk;
struct variant_data;
@@ -189,7 +179,8 @@ struct mmci_host {
unsigned int mclk;
unsigned int cclk;
- u32 pwr;
+ u32 pwr_reg;
+ u32 clk_reg;
struct mmci_platform_data *plat;
struct variant_data *variant;
diff --git a/drivers/mmc/host/s3cmci.c b/drivers/mmc/host/s3cmci.c
index 1bcfd6dbb5cc..c3622a69f432 100644
--- a/drivers/mmc/host/s3cmci.c
+++ b/drivers/mmc/host/s3cmci.c
@@ -1606,7 +1606,7 @@ static int __devinit s3cmci_probe(struct platform_device *pdev)
host->mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!host->mem) {
dev_err(&pdev->dev,
- "failed to get io memory region resouce.\n");
+ "failed to get io memory region resource.\n");
ret = -ENOENT;
goto probe_free_gpio;
@@ -1630,7 +1630,7 @@ static int __devinit s3cmci_probe(struct platform_device *pdev)
host->irq = platform_get_irq(pdev, 0);
if (host->irq == 0) {
- dev_err(&pdev->dev, "failed to get interrupt resouce.\n");
+ dev_err(&pdev->dev, "failed to get interrupt resource.\n");
ret = -EINVAL;
goto probe_iounmap;
}
diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c
index d601e41af282..0be4e2013632 100644
--- a/drivers/mmc/host/sdhci-esdhc-imx.c
+++ b/drivers/mmc/host/sdhci-esdhc-imx.c
@@ -269,8 +269,9 @@ static void esdhc_writew_le(struct sdhci_host *host, u16 val, int reg)
imx_data->scratchpad = val;
return;
case SDHCI_COMMAND:
- if ((host->cmd->opcode == MMC_STOP_TRANSMISSION)
- && (imx_data->flags & ESDHC_FLAG_MULTIBLK_NO_INT))
+ if ((host->cmd->opcode == MMC_STOP_TRANSMISSION ||
+ host->cmd->opcode == MMC_SET_BLOCK_COUNT) &&
+ (imx_data->flags & ESDHC_FLAG_MULTIBLK_NO_INT))
val |= SDHCI_CMD_ABORTCMD;
if (is_imx6q_usdhc(imx_data)) {
diff --git a/drivers/mmc/host/sh_mmcif.c b/drivers/mmc/host/sh_mmcif.c
index 352d4797865b..75a485448796 100644
--- a/drivers/mmc/host/sh_mmcif.c
+++ b/drivers/mmc/host/sh_mmcif.c
@@ -56,6 +56,7 @@
#include <linux/mmc/sh_mmcif.h>
#include <linux/pagemap.h>
#include <linux/platform_device.h>
+#include <linux/pm_qos.h>
#include <linux/pm_runtime.h>
#include <linux/spinlock.h>
#include <linux/module.h>
@@ -1346,6 +1347,8 @@ static int __devinit sh_mmcif_probe(struct platform_device *pdev)
if (ret < 0)
goto clean_up5;
+ dev_pm_qos_expose_latency_limit(&pdev->dev, 100);
+
dev_info(&pdev->dev, "driver version %s\n", DRIVER_VERSION);
dev_dbg(&pdev->dev, "chip ver H'%04x\n",
sh_mmcif_readl(host->addr, MMCIF_CE_VERSION) & 0x0000ffff);
@@ -1376,6 +1379,8 @@ static int __devexit sh_mmcif_remove(struct platform_device *pdev)
host->dying = true;
pm_runtime_get_sync(&pdev->dev);
+ dev_pm_qos_hide_latency_limit(&pdev->dev);
+
mmc_remove_host(host->mmc);
sh_mmcif_writel(host->addr, MMCIF_CE_INT_MASK, MASK_ALL);
diff --git a/drivers/mmc/host/tmio_mmc_pio.c b/drivers/mmc/host/tmio_mmc_pio.c
index 5f9ad74fbf80..e21988901c36 100644
--- a/drivers/mmc/host/tmio_mmc_pio.c
+++ b/drivers/mmc/host/tmio_mmc_pio.c
@@ -39,6 +39,7 @@
#include <linux/module.h>
#include <linux/pagemap.h>
#include <linux/platform_device.h>
+#include <linux/pm_qos.h>
#include <linux/pm_runtime.h>
#include <linux/scatterlist.h>
#include <linux/spinlock.h>
@@ -955,6 +956,8 @@ int __devinit tmio_mmc_host_probe(struct tmio_mmc_host **host,
mmc_add_host(mmc);
+ dev_pm_qos_expose_latency_limit(&pdev->dev, 100);
+
/* Unmask the IRQs we want to know about */
if (!_host->chan_rx)
irq_mask |= TMIO_MASK_READOP;
@@ -993,6 +996,8 @@ void tmio_mmc_host_remove(struct tmio_mmc_host *host)
|| host->mmc->caps & MMC_CAP_NONREMOVABLE)
pm_runtime_get_sync(&pdev->dev);
+ dev_pm_qos_hide_latency_limit(&pdev->dev);
+
mmc_remove_host(host->mmc);
cancel_work_sync(&host->done);
cancel_delayed_work_sync(&host->delayed_reset_work);
Powered by cgit, Gruvboxed by Blaster4385.