diff options
Diffstat (limited to 'drivers/bluetooth/hci_ldisc.c')
| -rw-r--r-- | drivers/bluetooth/hci_ldisc.c | 123 |
1 files changed, 123 insertions, 0 deletions
diff --git a/drivers/bluetooth/hci_ldisc.c b/drivers/bluetooth/hci_ldisc.c index 5c9a73f02664..177dd69fdd95 100644 --- a/drivers/bluetooth/hci_ldisc.c +++ b/drivers/bluetooth/hci_ldisc.c @@ -40,6 +40,7 @@ #include <linux/signal.h> #include <linux/ioctl.h> #include <linux/skbuff.h> +#include <linux/firmware.h> #include <net/bluetooth/bluetooth.h> #include <net/bluetooth/hci_core.h> @@ -265,11 +266,133 @@ static int hci_uart_send_frame(struct hci_dev *hdev, struct sk_buff *skb) return 0; } +/* Flow control or un-flow control the device */ +void hci_uart_set_flow_control(struct hci_uart *hu, bool enable) +{ + struct tty_struct *tty = hu->tty; + struct ktermios ktermios; + int status; + unsigned int set = 0; + unsigned int clear = 0; + + if (enable) { + /* Disable hardware flow control */ + ktermios = tty->termios; + ktermios.c_cflag &= ~CRTSCTS; + status = tty_set_termios(tty, &ktermios); + BT_DBG("Disabling hardware flow control: %s", + status ? "failed" : "success"); + + /* Clear RTS to prevent the device from sending */ + /* Most UARTs need OUT2 to enable interrupts */ + status = tty->driver->ops->tiocmget(tty); + BT_DBG("Current tiocm 0x%x", status); + + set &= ~(TIOCM_OUT2 | TIOCM_RTS); + clear = ~set; + set &= TIOCM_DTR | TIOCM_RTS | TIOCM_OUT1 | + TIOCM_OUT2 | TIOCM_LOOP; + clear &= TIOCM_DTR | TIOCM_RTS | TIOCM_OUT1 | + TIOCM_OUT2 | TIOCM_LOOP; + status = tty->driver->ops->tiocmset(tty, set, clear); + BT_DBG("Clearing RTS: %s", status ? "failed" : "success"); + } else { + /* Set RTS to allow the device to send again */ + status = tty->driver->ops->tiocmget(tty); + BT_DBG("Current tiocm 0x%x", status); + + set |= (TIOCM_OUT2 | TIOCM_RTS); + clear = ~set; + set &= TIOCM_DTR | TIOCM_RTS | TIOCM_OUT1 | + TIOCM_OUT2 | TIOCM_LOOP; + clear &= TIOCM_DTR | TIOCM_RTS | TIOCM_OUT1 | + TIOCM_OUT2 | TIOCM_LOOP; + status = tty->driver->ops->tiocmset(tty, set, clear); + BT_DBG("Setting RTS: %s", status ? "failed" : "success"); + + /* Re-enable hardware flow control */ + ktermios = tty->termios; + ktermios.c_cflag |= CRTSCTS; + status = tty_set_termios(tty, &ktermios); + BT_DBG("Enabling hardware flow control: %s", + status ? "failed" : "success"); + } +} + +void hci_uart_set_speeds(struct hci_uart *hu, unsigned int init_speed, + unsigned int oper_speed) +{ + hu->init_speed = init_speed; + hu->oper_speed = oper_speed; +} + +void hci_uart_init_tty(struct hci_uart *hu) +{ + struct tty_struct *tty = hu->tty; + struct ktermios ktermios; + + /* Bring the UART into a known 8 bits no parity hw fc state */ + ktermios = tty->termios; + ktermios.c_iflag &= ~(IGNBRK | BRKINT | PARMRK | ISTRIP | + INLCR | IGNCR | ICRNL | IXON); + ktermios.c_oflag &= ~OPOST; + ktermios.c_lflag &= ~(ECHO | ECHONL | ICANON | ISIG | IEXTEN); + ktermios.c_cflag &= ~(CSIZE | PARENB); + ktermios.c_cflag |= CS8; + ktermios.c_cflag |= CRTSCTS; + + /* tty_set_termios() return not checked as it is always 0 */ + tty_set_termios(tty, &ktermios); +} + +void hci_uart_set_baudrate(struct hci_uart *hu, unsigned int speed) +{ + struct tty_struct *tty = hu->tty; + struct ktermios ktermios; + + ktermios = tty->termios; + ktermios.c_cflag &= ~CBAUD; + tty_termios_encode_baud_rate(&ktermios, speed, speed); + + /* tty_set_termios() return not checked as it is always 0 */ + tty_set_termios(tty, &ktermios); + + BT_DBG("%s: New tty speeds: %d/%d", hu->hdev->name, + tty->termios.c_ispeed, tty->termios.c_ospeed); +} + static int hci_uart_setup(struct hci_dev *hdev) { struct hci_uart *hu = hci_get_drvdata(hdev); struct hci_rp_read_local_version *ver; struct sk_buff *skb; + unsigned int speed; + int err; + + /* Init speed if any */ + if (hu->init_speed) + speed = hu->init_speed; + else if (hu->proto->init_speed) + speed = hu->proto->init_speed; + else + speed = 0; + + if (speed) + hci_uart_set_baudrate(hu, speed); + + /* Operational speed if any */ + if (hu->oper_speed) + speed = hu->oper_speed; + else if (hu->proto->oper_speed) + speed = hu->proto->oper_speed; + else + speed = 0; + + if (hu->proto->set_baudrate && speed) { + err = hu->proto->set_baudrate(hu, speed); + if (!err) + hci_uart_set_baudrate(hu, speed); + } if (hu->proto->setup) return hu->proto->setup(hu); |