diff options
Diffstat (limited to 'arch/arm/boot/dts/st/stm32mp135f-dk.dts')
| -rw-r--r-- | arch/arm/boot/dts/st/stm32mp135f-dk.dts | 128 |
1 files changed, 128 insertions, 0 deletions
diff --git a/arch/arm/boot/dts/st/stm32mp135f-dk.dts b/arch/arm/boot/dts/st/stm32mp135f-dk.dts index 567e53ad285f..1af335a39993 100644 --- a/arch/arm/boot/dts/st/stm32mp135f-dk.dts +++ b/arch/arm/boot/dts/st/stm32mp135f-dk.dts @@ -19,6 +19,7 @@ compatible = "st,stm32mp135f-dk", "st,stm32mp135"; aliases { + ethernet0 = ðernet1; serial0 = &uart4; serial1 = &usart1; serial2 = &uart8; @@ -29,6 +30,20 @@ stdout-path = "serial0:115200n8"; }; + clocks { + clk_ext_camera: clk-ext-camera { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <24000000>; + }; + + clk_mco1: clk-mco1 { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <24000000>; + }; + }; + memory@c0000000 { device_type = "memory"; reg = <0xc0000000 0x20000000>; @@ -141,6 +156,45 @@ status = "okay"; }; +&dcmipp { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&dcmipp_pins_a>; + pinctrl-1 = <&dcmipp_sleep_pins_a>; + status = "okay"; + + port { + dcmipp_0: endpoint { + remote-endpoint = <&mipid02_2>; + bus-width = <8>; + hsync-active = <0>; + vsync-active = <0>; + pclk-sample = <0>; + }; + }; +}; + +ðernet1 { + status = "okay"; + pinctrl-0 = <ð1_rmii_pins_a>; + pinctrl-1 = <ð1_rmii_sleep_pins_a>; + pinctrl-names = "default", "sleep"; + phy-mode = "rmii"; + phy-handle = <&phy0_eth1>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + + phy0_eth1: ethernet-phy@0 { + compatible = "ethernet-phy-id0007.c131"; + reg = <0>; + reset-gpios = <&mcp23017 9 GPIO_ACTIVE_LOW>; + wakeup-source; + }; + }; +}; + &i2c1 { pinctrl-names = "default", "sleep"; pinctrl-0 = <&i2c1_pins_a>; @@ -201,6 +255,76 @@ /* spare dmas for other usage */ /delete-property/dmas; /delete-property/dma-names; + + stmipi: csi2rx@14 { + compatible = "st,st-mipid02"; + reg = <0x14>; + clocks = <&clk_mco1>; + clock-names = "xclk"; + VDDE-supply = <&scmi_v1v8_periph>; + VDDIN-supply = <&scmi_v1v8_periph>; + reset-gpios = <&mcp23017 2 (GPIO_ACTIVE_LOW | GPIO_PUSH_PULL)>; + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + + mipid02_0: endpoint { + data-lanes = <1 2>; + lane-polarities = <0 0 0>; + remote-endpoint = <&gc2145_ep>; + }; + }; + port@2 { + reg = <2>; + + mipid02_2: endpoint { + bus-width = <8>; + hsync-active = <0>; + vsync-active = <0>; + pclk-sample = <0>; + remote-endpoint = <&dcmipp_0>; + }; + }; + }; + }; + + gc2145: camera@3c { + compatible = "galaxycore,gc2145"; + reg = <0x3c>; + clocks = <&clk_ext_camera>; + iovdd-supply = <&scmi_v3v3_sw>; + avdd-supply = <&scmi_v3v3_sw>; + dvdd-supply = <&scmi_v3v3_sw>; + powerdown-gpios = <&mcp23017 3 (GPIO_ACTIVE_LOW | GPIO_PUSH_PULL)>; + reset-gpios = <&mcp23017 4 (GPIO_ACTIVE_LOW | GPIO_PUSH_PULL)>; + status = "okay"; + + port { + gc2145_ep: endpoint { + remote-endpoint = <&mipid02_0>; + data-lanes = <1 2>; + link-frequencies = /bits/ 64 <120000000 192000000 240000000>; + }; + }; + }; + + goodix: goodix-ts@5d { + compatible = "goodix,gt911"; + reg = <0x5d>; + pinctrl-names = "default"; + pinctrl-0 = <&goodix_pins_a>; + interrupt-parent = <&gpiof>; + interrupts = <5 IRQ_TYPE_EDGE_FALLING>; + AVDD28-supply = <&scmi_v3v3_sw>; + VDDIO-supply = <&scmi_v3v3_sw>; + touchscreen-size-x = <480>; + touchscreen-size-y = <272>; + status = "okay" ; + }; }; &iwdg2 { @@ -273,6 +397,7 @@ /delete-property/dma-names; status = "disabled"; pwm { + /* PWM output on pin 7 of the expansion connector (CN8.7) using TIM3_CH4 func */ pinctrl-0 = <&pwm3_pins_a>; pinctrl-1 = <&pwm3_sleep_pins_a>; pinctrl-names = "default", "sleep"; @@ -288,6 +413,7 @@ /delete-property/dma-names; status = "disabled"; pwm { + /* PWM output on pin 31 of the expansion connector (CN8.31) using TIM4_CH2 func */ pinctrl-0 = <&pwm4_pins_a>; pinctrl-1 = <&pwm4_sleep_pins_a>; pinctrl-names = "default", "sleep"; @@ -303,6 +429,7 @@ /delete-property/dma-names; status = "disabled"; pwm { + /* PWM output on pin 32 of the expansion connector (CN8.32) using TIM8_CH3 func */ pinctrl-0 = <&pwm8_pins_a>; pinctrl-1 = <&pwm8_sleep_pins_a>; pinctrl-names = "default", "sleep"; @@ -316,6 +443,7 @@ &timers14 { status = "disabled"; pwm { + /* PWM output on pin 33 of the expansion connector (CN8.33) using TIM14_CH1 func */ pinctrl-0 = <&pwm14_pins_a>; pinctrl-1 = <&pwm14_sleep_pins_a>; pinctrl-names = "default", "sleep"; |