diff options
Diffstat (limited to 'Documentation/devicetree')
21 files changed, 367 insertions, 17 deletions
diff --git a/Documentation/devicetree/bindings/arm/exynos/power_domain.txt b/Documentation/devicetree/bindings/arm/exynos/power_domain.txt index f4445e5a2bbb..1e097037349c 100644 --- a/Documentation/devicetree/bindings/arm/exynos/power_domain.txt +++ b/Documentation/devicetree/bindings/arm/exynos/power_domain.txt @@ -22,6 +22,8 @@ Optional Properties: - pclkN, clkN: Pairs of parent of input clock and input clock to the devices in this power domain. Maximum of 4 pairs (N = 0 to 3) are supported currently. +- power-domains: phandle pointing to the parent power domain, for more details + see Documentation/devicetree/bindings/power/power_domain.txt Node of a device using power domains must have a power-domains property defined with a phandle to respective power domain. diff --git a/Documentation/devicetree/bindings/arm/sti.txt b/Documentation/devicetree/bindings/arm/sti.txt index d70ec358736c..8d27f6b084c7 100644 --- a/Documentation/devicetree/bindings/arm/sti.txt +++ b/Documentation/devicetree/bindings/arm/sti.txt @@ -13,6 +13,10 @@ Boards with the ST STiH407 SoC shall have the following properties: Required root node property: compatible = "st,stih407"; +Boards with the ST STiH410 SoC shall have the following properties: +Required root node property: +compatible = "st,stih410"; + Boards with the ST STiH418 SoC shall have the following properties: Required root node property: compatible = "st,stih418"; diff --git a/Documentation/devicetree/bindings/i2c/i2c-imx.txt b/Documentation/devicetree/bindings/i2c/i2c-imx.txt index 52d37fd8d3e5..ce4311d726ae 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-imx.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-imx.txt @@ -7,6 +7,7 @@ Required properties: - "fsl,vf610-i2c" for I2C compatible with the one integrated on Vybrid vf610 SoC - reg : Should contain I2C/HS-I2C registers location and length - interrupts : Should contain I2C/HS-I2C interrupt +- clocks : Should contain the I2C/HS-I2C clock specifier Optional properties: - clock-frequency : Constains desired I2C/HS-I2C bus clock frequency in Hz. diff --git a/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt b/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt index 33df3932168e..8db32384a486 100644 --- a/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt +++ b/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt @@ -27,6 +27,8 @@ property is used. - amd,serdes-cdr-rate: CDR rate speed selection - amd,serdes-pq-skew: PQ (data sampling) skew - amd,serdes-tx-amp: TX amplitude boost +- amd,serdes-dfe-tap-config: DFE taps available to run +- amd,serdes-dfe-tap-enable: DFE taps to enable Example: xgbe_phy@e1240800 { @@ -41,4 +43,6 @@ Example: amd,serdes-cdr-rate = <2>, <2>, <7>; amd,serdes-pq-skew = <10>, <10>, <30>; amd,serdes-tx-amp = <15>, <15>, <10>; + amd,serdes-dfe-tap-config = <3>, <3>, <1>; + amd,serdes-dfe-tap-enable = <0>, <0>, <127>; }; diff --git a/Documentation/devicetree/bindings/net/apm-xgene-enet.txt b/Documentation/devicetree/bindings/net/apm-xgene-enet.txt index cfcc52705ed8..6151999c5dca 100644 --- a/Documentation/devicetree/bindings/net/apm-xgene-enet.txt +++ b/Documentation/devicetree/bindings/net/apm-xgene-enet.txt @@ -4,7 +4,10 @@ Ethernet nodes are defined to describe on-chip ethernet interfaces in APM X-Gene SoC. Required properties for all the ethernet interfaces: -- compatible: Should be "apm,xgene-enet" +- compatible: Should state binding information from the following list, + - "apm,xgene-enet": RGMII based 1G interface + - "apm,xgene1-sgenet": SGMII based 1G interface + - "apm,xgene1-xgenet": XFI based 10G interface - reg: Address and length of the register set for the device. It contains the information of registers in the same order as described by reg-names - reg-names: Should contain the register set names diff --git a/Documentation/devicetree/bindings/net/dsa/dsa.txt b/Documentation/devicetree/bindings/net/dsa/dsa.txt index e124847443f8..f0b4cd72411d 100644 --- a/Documentation/devicetree/bindings/net/dsa/dsa.txt +++ b/Documentation/devicetree/bindings/net/dsa/dsa.txt @@ -19,7 +19,9 @@ the parent DSA node. The maximum number of allowed child nodes is 4 (DSA_MAX_SWITCHES). Each of these switch child nodes should have the following required properties: -- reg : Describes the switch address on the MII bus +- reg : Contains two fields. The first one describes the + address on the MII bus. The second is the switch + number that must be unique in cascaded configurations - #address-cells : Must be 1 - #size-cells : Must be 0 diff --git a/Documentation/devicetree/bindings/power/power_domain.txt b/Documentation/devicetree/bindings/power/power_domain.txt index 98c16672ab5f..0f8ed3710c66 100644 --- a/Documentation/devicetree/bindings/power/power_domain.txt +++ b/Documentation/devicetree/bindings/power/power_domain.txt @@ -19,6 +19,16 @@ Required properties: providing multiple PM domains (e.g. power controllers), but can be any value as specified by device tree binding documentation of particular provider. +Optional properties: + - power-domains : A phandle and PM domain specifier as defined by bindings of + the power controller specified by phandle. + Some power domains might be powered from another power domain (or have + other hardware specific dependencies). For representing such dependency + a standard PM domain consumer binding is used. When provided, all domains + created by the given provider should be subdomains of the domain + specified by this binding. More details about power domain specifier are + available in the next section. + Example: power: power-controller@12340000 { @@ -30,6 +40,25 @@ Example: The node above defines a power controller that is a PM domain provider and expects one cell as its phandle argument. +Example 2: + + parent: power-controller@12340000 { + compatible = "foo,power-controller"; + reg = <0x12340000 0x1000>; + #power-domain-cells = <1>; + }; + + child: power-controller@12340000 { + compatible = "foo,power-controller"; + reg = <0x12341000 0x1000>; + power-domains = <&parent 0>; + #power-domain-cells = <1>; + }; + +The nodes above define two power controllers: 'parent' and 'child'. +Domains created by the 'child' power controller are subdomains of '0' power +domain provided by the 'parent' power controller. + ==PM domain consumers== Required properties: diff --git a/Documentation/devicetree/bindings/serial/of-serial.txt b/Documentation/devicetree/bindings/serial/8250.txt index 91d5ab0e60fc..91d5ab0e60fc 100644 --- a/Documentation/devicetree/bindings/serial/of-serial.txt +++ b/Documentation/devicetree/bindings/serial/8250.txt diff --git a/Documentation/devicetree/bindings/serial/axis,etraxfs-uart.txt b/Documentation/devicetree/bindings/serial/axis,etraxfs-uart.txt new file mode 100644 index 000000000000..ebcbb62c0a76 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/axis,etraxfs-uart.txt @@ -0,0 +1,19 @@ +ETRAX FS UART + +Required properties: +- compatible : "axis,etraxfs-uart" +- reg: offset and length of the register set for the device. +- interrupts: device interrupt + +Optional properties: +- {dtr,dsr,ri,cd}-gpios: specify a GPIO for DTR/DSR/RI/CD + line respectively. + +Example: + +serial@b00260000 { + compatible = "axis,etraxfs-uart"; + reg = <0xb0026000 0x1000>; + interrupts = <68>; + status = "disabled"; +}; diff --git a/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt b/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt index 7f76214f728a..289c40ed7470 100644 --- a/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt +++ b/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt @@ -21,6 +21,18 @@ Optional properties: - reg-io-width : the size (in bytes) of the IO accesses that should be performed on the device. If this property is not present then single byte accesses are used. +- dcd-override : Override the DCD modem status signal. This signal will always + be reported as active instead of being obtained from the modem status + register. Define this if your serial port does not use this pin. +- dsr-override : Override the DTS modem status signal. This signal will always + be reported as active instead of being obtained from the modem status + register. Define this if your serial port does not use this pin. +- cts-override : Override the CTS modem status signal. This signal will always + be reported as active instead of being obtained from the modem status + register. Define this if your serial port does not use this pin. +- ri-override : Override the RI modem status signal. This signal will always be + reported as inactive instead of being obtained from the modem status register. + Define this if your serial port does not use this pin. Example: @@ -31,6 +43,10 @@ Example: interrupts = <10>; reg-shift = <2>; reg-io-width = <4>; + dcd-override; + dsr-override; + cts-override; + ri-override; }; Example with one clock: diff --git a/Documentation/devicetree/bindings/sound/ingenic,jz4740-i2s.txt b/Documentation/devicetree/bindings/sound/ingenic,jz4740-i2s.txt index b41433386e2f..b623d50004fb 100644 --- a/Documentation/devicetree/bindings/sound/ingenic,jz4740-i2s.txt +++ b/Documentation/devicetree/bindings/sound/ingenic,jz4740-i2s.txt @@ -1,7 +1,7 @@ Ingenic JZ4740 I2S controller Required properties: -- compatible : "ingenic,jz4740-i2s" +- compatible : "ingenic,jz4740-i2s" or "ingenic,jz4780-i2s" - reg : I2S registers location and length - clocks : AIC and I2S PLL clock specifiers. - clock-names: "aic" and "i2s" diff --git a/Documentation/devicetree/bindings/sound/max98925.txt b/Documentation/devicetree/bindings/sound/max98925.txt new file mode 100644 index 000000000000..27be63e2aa0d --- /dev/null +++ b/Documentation/devicetree/bindings/sound/max98925.txt @@ -0,0 +1,22 @@ +max98925 audio CODEC + +This device supports I2C. + +Required properties: + + - compatible : "maxim,max98925" + + - vmon-slot-no : slot number used to send voltage information + + - imon-slot-no : slot number used to send current information + + - reg : the I2C address of the device for I2C + +Example: + +codec: max98925@1a { + compatible = "maxim,max98925"; + vmon-slot-no = <0>; + imon-slot-no = <2>; + reg = <0x1a>; +}; diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-max98090.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-max98090.txt index c949abc2992f..c3495beba358 100644 --- a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-max98090.txt +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-max98090.txt @@ -18,6 +18,7 @@ Required properties: * Headphones * Speakers * Mic Jack + * Int Mic - nvidia,i2s-controller : The phandle of the Tegra I2S controller that's connected to the CODEC. diff --git a/Documentation/devicetree/bindings/sound/qcom,lpass-cpu.txt b/Documentation/devicetree/bindings/sound/qcom,lpass-cpu.txt new file mode 100644 index 000000000000..e00732dac939 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/qcom,lpass-cpu.txt @@ -0,0 +1,43 @@ +* Qualcomm Technologies LPASS CPU DAI + +This node models the Qualcomm Technologies Low-Power Audio SubSystem (LPASS). + +Required properties: + +- compatible : "qcom,lpass-cpu" +- clocks : Must contain an entry for each entry in clock-names. +- clock-names : A list which must include the following entries: + * "ahbix-clk" + * "mi2s-osr-clk" + * "mi2s-bit-clk" +- interrupts : Must contain an entry for each entry in + interrupt-names. +- interrupt-names : A list which must include the following entries: + * "lpass-irq-lpaif" +- pinctrl-N : One property must exist for each entry in + pinctrl-names. See ../pinctrl/pinctrl-bindings.txt + for details of the property values. +- pinctrl-names : Must contain a "default" entry. +- reg : Must contain an address for each entry in reg-names. +- reg-names : A list which must include the following entries: + * "lpass-lpaif" + +Optional properties: + +- qcom,adsp : Phandle for the audio DSP node + +Example: + +lpass@28100000 { + compatible = "qcom,lpass-cpu"; + clocks = <&lcc AHBIX_CLK>, <&lcc MI2S_OSR_CLK>, <&lcc MI2S_BIT_CLK>; + clock-names = "ahbix-clk", "mi2s-osr-clk", "mi2s-bit-clk"; + interrupts = <0 85 1>; + interrupt-names = "lpass-irq-lpaif"; + pinctrl-names = "default", "idle"; + pinctrl-0 = <&mi2s_default>; + pinctrl-1 = <&mi2s_idle>; + reg = <0x28100000 0x10000>; + reg-names = "lpass-lpaif"; + qcom,adsp = <&adsp>; +}; diff --git a/Documentation/devicetree/bindings/sound/renesas,rsnd.txt b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt index 2dd690bc19cc..f316ce1f214a 100644 --- a/Documentation/devicetree/bindings/sound/renesas,rsnd.txt +++ b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt @@ -29,9 +29,17 @@ SSI subnode properties: - shared-pin : if shared clock pin - pio-transfer : use PIO transfer mode - no-busif : BUSIF is not ussed when [mem -> SSI] via DMA case +- dma : Should contain Audio DMAC entry +- dma-names : SSI case "rx" (=playback), "tx" (=capture) + SSIU case "rxu" (=playback), "txu" (=capture) SRC subnode properties: -no properties at this point +- dma : Should contain Audio DMAC entry +- dma-names : "rx" (=playback), "tx" (=capture) + +DVC subnode properties: +- dma : Should contain Audio DMAC entry +- dma-names : "tx" (=playback/capture) DAI subnode properties: - playback : list of playback modules @@ -45,56 +53,145 @@ rcar_sound: rcar_sound@ec500000 { reg = <0 0xec500000 0 0x1000>, /* SCU */ <0 0xec5a0000 0 0x100>, /* ADG */ <0 0xec540000 0 0x1000>, /* SSIU */ - <0 0xec541000 0 0x1280>; /* SSI */ + <0 0xec541000 0 0x1280>, /* SSI */ + <0 0xec740000 0 0x200>; /* Audio DMAC peri peri*/ + reg-names = "scu", "adg", "ssiu", "ssi", "audmapp"; + + clocks = <&mstp10_clks R8A7790_CLK_SSI_ALL>, + <&mstp10_clks R8A7790_CLK_SSI9>, <&mstp10_clks R8A7790_CLK_SSI8>, + <&mstp10_clks R8A7790_CLK_SSI7>, <&mstp10_clks R8A7790_CLK_SSI6>, + <&mstp10_clks R8A7790_CLK_SSI5>, <&mstp10_clks R8A7790_CLK_SSI4>, + <&mstp10_clks R8A7790_CLK_SSI3>, <&mstp10_clks R8A7790_CLK_SSI2>, + <&mstp10_clks R8A7790_CLK_SSI1>, <&mstp10_clks R8A7790_CLK_SSI0>, + <&mstp10_clks R8A7790_CLK_SCU_SRC9>, <&mstp10_clks R8A7790_CLK_SCU_SRC8>, + <&mstp10_clks R8A7790_CLK_SCU_SRC7>, <&mstp10_clks R8A7790_CLK_SCU_SRC6>, + <&mstp10_clks R8A7790_CLK_SCU_SRC5>, <&mstp10_clks R8A7790_CLK_SCU_SRC4>, + <&mstp10_clks R8A7790_CLK_SCU_SRC3>, <&mstp10_clks R8A7790_CLK_SCU_SRC2>, + <&mstp10_clks R8A7790_CLK_SCU_SRC1>, <&mstp10_clks R8A7790_CLK_SCU_SRC0>, + <&mstp10_clks R8A7790_CLK_SCU_DVC0>, <&mstp10_clks R8A7790_CLK_SCU_DVC1>, + <&audio_clk_a>, <&audio_clk_b>, <&audio_clk_c>, <&m2_clk>; + clock-names = "ssi-all", + "ssi.9", "ssi.8", "ssi.7", "ssi.6", "ssi.5", + "ssi.4", "ssi.3", "ssi.2", "ssi.1", "ssi.0", + "src.9", "src.8", "src.7", "src.6", "src.5", + "src.4", "src.3", "src.2", "src.1", "src.0", + "dvc.0", "dvc.1", + "clk_a", "clk_b", "clk_c", "clk_i"; rcar_sound,dvc { - dvc0: dvc@0 { }; - dvc1: dvc@1 { }; + dvc0: dvc@0 { + dmas = <&audma0 0xbc>; + dma-names = "tx"; + }; + dvc1: dvc@1 { + dmas = <&audma0 0xbe>; + dma-names = "tx"; + }; }; rcar_sound,src { - src0: src@0 { }; - src1: src@1 { }; - src2: src@2 { }; - src3: src@3 { }; - src4: src@4 { }; - src5: src@5 { }; - src6: src@6 { }; - src7: src@7 { }; - src8: src@8 { }; - src9: src@9 { }; + src0: src@0 { + interrupts = <0 352 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x85>, <&audma1 0x9a>; + dma-names = "rx", "tx"; + }; + src1: src@1 { + interrupts = <0 353 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x87>, <&audma1 0x9c>; + dma-names = "rx", "tx"; + }; + src2: src@2 { + interrupts = <0 354 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x89>, <&audma1 0x9e>; + dma-names = "rx", "tx"; + }; + src3: src@3 { + interrupts = <0 355 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x8b>, <&audma1 0xa0>; + dma-names = "rx", "tx"; + }; + src4: src@4 { + interrupts = <0 356 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x8d>, <&audma1 0xb0>; + dma-names = "rx", "tx"; + }; + src5: src@5 { + interrupts = <0 357 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x8f>, <&audma1 0xb2>; + dma-names = "rx", "tx"; + }; + src6: src@6 { + interrupts = <0 358 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x91>, <&audma1 0xb4>; + dma-names = "rx", "tx"; + }; + src7: src@7 { + interrupts = <0 359 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x93>, <&audma1 0xb6>; + dma-names = "rx", "tx"; + }; + src8: src@8 { + interrupts = <0 360 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x95>, <&audma1 0xb8>; + dma-names = "rx", "tx"; + }; + src9: src@9 { + interrupts = <0 361 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x97>, <&audma1 0xba>; + dma-names = "rx", "tx"; + }; }; rcar_sound,ssi { ssi0: ssi@0 { interrupts = <0 370 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x01>, <&audma1 0x02>, <&audma0 0x15>, <&audma1 0x16>; + dma-names = "rx", "tx", "rxu", "txu"; }; ssi1: ssi@1 { interrupts = <0 371 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x03>, <&audma1 0x04>, <&audma0 0x49>, <&audma1 0x4a>; + dma-names = "rx", "tx", "rxu", "txu"; }; ssi2: ssi@2 { interrupts = <0 372 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x05>, <&audma1 0x06>, <&audma0 0x63>, <&audma1 0x64>; + dma-names = "rx", "tx", "rxu", "txu"; }; ssi3: ssi@3 { interrupts = <0 373 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x07>, <&audma1 0x08>, <&audma0 0x6f>, <&audma1 0x70>; + dma-names = "rx", "tx", "rxu", "txu"; }; ssi4: ssi@4 { interrupts = <0 374 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x09>, <&audma1 0x0a>, <&audma0 0x71>, <&audma1 0x72>; + dma-names = "rx", "tx", "rxu", "txu"; }; ssi5: ssi@5 { interrupts = <0 375 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x0b>, <&audma1 0x0c>, <&audma0 0x73>, <&audma1 0x74>; + dma-names = "rx", "tx", "rxu", "txu"; }; ssi6: ssi@6 { interrupts = <0 376 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x0d>, <&audma1 0x0e>, <&audma0 0x75>, <&audma1 0x76>; + dma-names = "rx", "tx", "rxu", "txu"; }; ssi7: ssi@7 { interrupts = <0 377 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x0f>, <&audma1 0x10>, <&audma0 0x79>, <&audma1 0x7a>; + dma-names = "rx", "tx", "rxu", "txu"; }; ssi8: ssi@8 { interrupts = <0 378 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x11>, <&audma1 0x12>, <&audma0 0x7b>, <&audma1 0x7c>; + dma-names = "rx", "tx", "rxu", "txu"; }; ssi9: ssi@9 { interrupts = <0 379 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x13>, <&audma1 0x14>, <&audma0 0x7d>, <&audma1 0x7e>; + dma-names = "rx", "tx", "rxu", "txu"; }; }; diff --git a/Documentation/devicetree/bindings/sound/renesas,rsrc-card.txt b/Documentation/devicetree/bindings/sound/renesas,rsrc-card.txt new file mode 100644 index 000000000000..c64155027288 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/renesas,rsrc-card.txt @@ -0,0 +1,67 @@ +Renesas Sampling Rate Convert Sound Card: + +Renesas Sampling Rate Convert Sound Card specifies audio DAI connections of SoC <-> codec. + +Required properties: + +- compatible : "renesas,rsrc-card,<board>" + Examples with soctypes are: + - "renesas,rsrc-card,lager" + - "renesas,rsrc-card,koelsch" +Optional properties: + +- card_name : User specified audio sound card name, one string + property. +- cpu : CPU sub-node +- codec : CODEC sub-node + +Optional subnode properties: + +- format : CPU/CODEC common audio format. + "i2s", "right_j", "left_j" , "dsp_a" + "dsp_b", "ac97", "pdm", "msb", "lsb" +- frame-master : Indicates dai-link frame master. + phandle to a cpu or codec subnode. +- bitclock-master : Indicates dai-link bit clock master. + phandle to a cpu or codec subnode. +- bitclock-inversion : bool property. Add this if the + dai-link uses bit clock inversion. +- frame-inversion : bool property. Add this if the + dai-link uses frame clock inversion. +- convert-rate : platform specified sampling rate convert + +Required CPU/CODEC subnodes properties: + +- sound-dai : phandle and port of CPU/CODEC + +Optional CPU/CODEC subnodes properties: + +- clocks / system-clock-frequency : specify subnode's clock if needed. + it can be specified via "clocks" if system has + clock node (= common clock), or "system-clock-frequency" + (if system doens't support common clock) + If a clock is specified, it is + enabled with clk_prepare_enable() + in dai startup() and disabled with + clk_disable_unprepare() in dai + shutdown(). + +Example + +sound { + compatible = "renesas,rsrc-card,lager"; + + card-name = "rsnd-ak4643"; + format = "left_j"; + bitclock-master = <&sndcodec>; + frame-master = <&sndcodec>; + + sndcpu: cpu { + sound-dai = <&rcar_sound>; + }; + + sndcodec: codec { + sound-dai = <&ak4643>; + system-clock-frequency = <11289600>; + }; +}; diff --git a/Documentation/devicetree/bindings/sound/storm.txt b/Documentation/devicetree/bindings/sound/storm.txt new file mode 100644 index 000000000000..062a4c185fa9 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/storm.txt @@ -0,0 +1,23 @@ +* Sound complex for Storm boards + +Models a soundcard for Storm boards with the Qualcomm Technologies IPQ806x SOC +connected to a MAX98357A DAC via I2S. + +Required properties: + +- compatible : "google,storm-audio" +- cpu : Phandle of the CPU DAI +- codec : Phandle of the codec DAI + +Optional properties: + +- qcom,model : The user-visible name of this sound card. + +Example: + +sound { + compatible = "google,storm-audio"; + qcom,model = "ipq806x-storm"; + cpu = <&lpass_cpu>; + codec = <&max98357a>; +}; diff --git a/Documentation/devicetree/bindings/sound/wm8804.txt b/Documentation/devicetree/bindings/sound/wm8804.txt index 4d3a56f38adc..6fd124b16496 100644 --- a/Documentation/devicetree/bindings/sound/wm8804.txt +++ b/Documentation/devicetree/bindings/sound/wm8804.txt @@ -10,6 +10,13 @@ Required properties: - reg : the I2C address of the device for I2C, the chip select number for SPI. + - PVDD-supply, DVDD-supply : Power supplies for the device, as covered + in Documentation/devicetree/bindings/regulator/regulator.txt + +Optional properties: + + - wlf,reset-gpio: A GPIO specifier for the GPIO controlling the reset pin + Example: codec: wm8804@1a { diff --git a/Documentation/devicetree/bindings/submitting-patches.txt b/Documentation/devicetree/bindings/submitting-patches.txt index 56742bc70218..7d44eae7ab0b 100644 --- a/Documentation/devicetree/bindings/submitting-patches.txt +++ b/Documentation/devicetree/bindings/submitting-patches.txt @@ -12,6 +12,9 @@ I. For patch submitters devicetree@vger.kernel.org + and Cc: the DT maintainers. Use scripts/get_maintainer.pl to identify + all of the DT maintainers. + 3) The Documentation/ portion of the patch should come in the series before the code implementing the binding. diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 389ca1347a77..fae26d014aaf 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -20,6 +20,7 @@ amlogic Amlogic, Inc. ams AMS AG amstaos AMS-Taos Inc. apm Applied Micro Circuits Corporation (APM) +arasan Arasan Chip Systems arm ARM Ltd. armadeus ARMadeus Systems SARL asahi-kasei Asahi Kasei Corp. @@ -27,6 +28,7 @@ atmel Atmel Corporation auo AU Optronics Corporation avago Avago Technologies avic Shanghai AVIC Optoelectronics Co., Ltd. +axis Axis Communications AB bosch Bosch Sensortec GmbH brcm Broadcom Corporation buffalo Buffalo, Inc. diff --git a/Documentation/devicetree/bindings/watchdog/atmel-wdt.txt b/Documentation/devicetree/bindings/watchdog/atmel-wdt.txt index f90e294d7631..a4d869744f59 100644 --- a/Documentation/devicetree/bindings/watchdog/atmel-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/atmel-wdt.txt @@ -26,6 +26,11 @@ Optional properties: - atmel,disable : Should be present if you want to disable the watchdog. - atmel,idle-halt : Should be present if you want to stop the watchdog when entering idle state. + CAUTION: This property should be used with care, it actually makes the + watchdog not counting when the CPU is in idle state, therefore the + watchdog reset time depends on mean CPU usage and will not reset at all + if the CPU stop working while it is in idle state, which is probably + not what you want. - atmel,dbg-halt : Should be present if you want to stop the watchdog when entering debug state. |