diff options
Diffstat (limited to 'Documentation/devicetree/bindings/fpga')
4 files changed, 144 insertions, 105 deletions
diff --git a/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt deleted file mode 100644 index 0acdfa6d62a4..000000000000 --- a/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt +++ /dev/null @@ -1,54 +0,0 @@ -Xilinx LogiCORE Partial Reconfig Decoupler Softcore - -The Xilinx LogiCORE Partial Reconfig Decoupler manages one or more -decouplers / fpga bridges. -The controller can decouple/disable the bridges which prevents signal -changes from passing through the bridge. The controller can also -couple / enable the bridges which allows traffic to pass through the -bridge normally. - -Xilinx LogiCORE Dynamic Function eXchange(DFX) AXI shutdown manager -Softcore is compatible with the Xilinx LogiCORE pr-decoupler. - -The Dynamic Function eXchange AXI shutdown manager prevents AXI traffic -from passing through the bridge. The controller safely handles AXI4MM -and AXI4-Lite interfaces on a Reconfigurable Partition when it is -undergoing dynamic reconfiguration, preventing the system deadlock -that can occur if AXI transactions are interrupted by DFX - -The Driver supports only MMIO handling. A PR region can have multiple -PR Decouplers which can be handled independently or chained via decouple/ -decouple_status signals. - -Required properties: -- compatible : Should contain "xlnx,pr-decoupler-1.00" followed by - "xlnx,pr-decoupler" or - "xlnx,dfx-axi-shutdown-manager-1.00" followed by - "xlnx,dfx-axi-shutdown-manager" -- regs : base address and size for decoupler module -- clocks : input clock to IP -- clock-names : should contain "aclk" - -See Documentation/devicetree/bindings/fpga/fpga-region.txt and -Documentation/devicetree/bindings/fpga/fpga-bridge.txt for generic bindings. - -Example: -Partial Reconfig Decoupler: - fpga-bridge@100000450 { - compatible = "xlnx,pr-decoupler-1.00", - "xlnx-pr-decoupler"; - regs = <0x10000045 0x10>; - clocks = <&clkc 15>; - clock-names = "aclk"; - bridge-enable = <0>; - }; - -Dynamic Function eXchange AXI shutdown manager: - fpga-bridge@100000450 { - compatible = "xlnx,dfx-axi-shutdown-manager-1.00", - "xlnx,dfx-axi-shutdown-manager"; - regs = <0x10000045 0x10>; - clocks = <&clkc 15>; - clock-names = "aclk"; - bridge-enable = <0>; - }; diff --git a/Documentation/devicetree/bindings/fpga/xilinx-slave-serial.txt b/Documentation/devicetree/bindings/fpga/xilinx-slave-serial.txt deleted file mode 100644 index 5ef659c1394d..000000000000 --- a/Documentation/devicetree/bindings/fpga/xilinx-slave-serial.txt +++ /dev/null @@ -1,51 +0,0 @@ -Xilinx Slave Serial SPI FPGA Manager - -Xilinx Spartan-6 and 7 Series FPGAs support a method of loading the -bitstream over what is referred to as "slave serial" interface. -The slave serial link is not technically SPI, and might require extra -circuits in order to play nicely with other SPI slaves on the same bus. - -See: -- https://www.xilinx.com/support/documentation/user_guides/ug380.pdf -- https://www.xilinx.com/support/documentation/user_guides/ug470_7Series_Config.pdf -- https://www.xilinx.com/support/documentation/application_notes/xapp583-fpga-configuration.pdf - -Required properties: -- compatible: should contain "xlnx,fpga-slave-serial" -- reg: spi chip select of the FPGA -- prog_b-gpios: config pin (referred to as PROGRAM_B in the manual) -- done-gpios: config status pin (referred to as DONE in the manual) - -Optional properties: -- init-b-gpios: initialization status and configuration error pin - (referred to as INIT_B in the manual) - -Example for full FPGA configuration: - - fpga-region0 { - compatible = "fpga-region"; - fpga-mgr = <&fpga_mgr_spi>; - #address-cells = <0x1>; - #size-cells = <0x1>; - }; - - spi1: spi@10680 { - compatible = "marvell,armada-xp-spi", "marvell,orion-spi"; - pinctrl-0 = <&spi0_pins>; - pinctrl-names = "default"; - #address-cells = <1>; - #size-cells = <0>; - cell-index = <1>; - interrupts = <92>; - clocks = <&coreclk 0>; - - fpga_mgr_spi: fpga-mgr@0 { - compatible = "xlnx,fpga-slave-serial"; - spi-max-frequency = <60000000>; - spi-cpha; - reg = <0>; - prog_b-gpios = <&gpio0 29 GPIO_ACTIVE_LOW>; - init-b-gpios = <&gpio0 28 GPIO_ACTIVE_LOW>; - done-gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>; - }; - }; diff --git a/Documentation/devicetree/bindings/fpga/xlnx,fpga-slave-serial.yaml b/Documentation/devicetree/bindings/fpga/xlnx,fpga-slave-serial.yaml new file mode 100644 index 000000000000..614d86ad825f --- /dev/null +++ b/Documentation/devicetree/bindings/fpga/xlnx,fpga-slave-serial.yaml @@ -0,0 +1,80 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/fpga/xlnx,fpga-slave-serial.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Xilinx Slave Serial SPI FPGA + +maintainers: + - Nava kishore Manne <nava.kishore.manne@amd.com> + +description: | + Xilinx Spartan-6 and 7 Series FPGAs support a method of loading the bitstream + over what is referred to as slave serial interface.The slave serial link is + not technically SPI, and might require extra circuits in order to play nicely + with other SPI slaves on the same bus. + + Datasheets: + https://www.xilinx.com/support/documentation/user_guides/ug380.pdf + https://www.xilinx.com/support/documentation/user_guides/ug470_7Series_Config.pdf + https://www.xilinx.com/support/documentation/application_notes/xapp583-fpga-configuration.pdf + +allOf: + - $ref: /schemas/spi/spi-peripheral-props.yaml# + +properties: + compatible: + enum: + - xlnx,fpga-slave-serial + + spi-cpha: true + + spi-max-frequency: + maximum: 60000000 + + reg: + maxItems: 1 + + prog_b-gpios: + description: + config pin (referred to as PROGRAM_B in the manual) + maxItems: 1 + + done-gpios: + description: + config status pin (referred to as DONE in the manual) + maxItems: 1 + + init-b-gpios: + description: + initialization status and configuration error pin + (referred to as INIT_B in the manual) + maxItems: 1 + +required: + - compatible + - reg + - prog_b-gpios + - done-gpios + - init-b-gpios + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + spi { + #address-cells = <1>; + #size-cells = <0>; + fpga_mgr_spi: fpga-mgr@0 { + compatible = "xlnx,fpga-slave-serial"; + spi-max-frequency = <60000000>; + spi-cpha; + reg = <0>; + prog_b-gpios = <&gpio0 29 GPIO_ACTIVE_LOW>; + init-b-gpios = <&gpio0 28 GPIO_ACTIVE_LOW>; + done-gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/fpga/xlnx,pr-decoupler.yaml b/Documentation/devicetree/bindings/fpga/xlnx,pr-decoupler.yaml new file mode 100644 index 000000000000..a7d4b8e59e19 --- /dev/null +++ b/Documentation/devicetree/bindings/fpga/xlnx,pr-decoupler.yaml @@ -0,0 +1,64 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/fpga/xlnx,pr-decoupler.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Xilinx LogiCORE Partial Reconfig Decoupler/AXI shutdown manager Softcore + +maintainers: + - Nava kishore Manne <nava.kishore.manne@amd.com> + +description: | + The Xilinx LogiCORE Partial Reconfig(PR) Decoupler manages one or more + decouplers/fpga bridges. The controller can decouple/disable the bridges + which prevents signal changes from passing through the bridge. The controller + can also couple / enable the bridges which allows traffic to pass through the + bridge normally. + Xilinx LogiCORE Dynamic Function eXchange(DFX) AXI shutdown manager Softcore + is compatible with the Xilinx LogiCORE pr-decoupler. The Dynamic Function + eXchange AXI shutdown manager prevents AXI traffic from passing through the + bridge. The controller safely handles AXI4MM and AXI4-Lite interfaces on a + Reconfigurable Partition when it is undergoing dynamic reconfiguration, + preventing the system deadlock that can occur if AXI transactions are + interrupted by DFX. + Please refer to fpga-region.txt and fpga-bridge.txt in this directory for + common binding part and usage. + +properties: + compatible: + oneOf: + - items: + - const: xlnx,pr-decoupler-1.00 + - const: xlnx,pr-decoupler + - items: + - const: xlnx,dfx-axi-shutdown-manager-1.00 + - const: xlnx,dfx-axi-shutdown-manager + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + items: + - const: aclk + +required: + - compatible + - reg + - clocks + - clock-names + +additionalProperties: false + +examples: + - | + fpga-bridge@100000450 { + compatible = "xlnx,pr-decoupler-1.00", "xlnx,pr-decoupler"; + reg = <0x10000045 0x10>; + clocks = <&clkc 15>; + clock-names = "aclk"; + }; +... |