diff options
Diffstat (limited to 'Documentation/admin-guide/kernel-parameters.txt')
| -rw-r--r-- | Documentation/admin-guide/kernel-parameters.txt | 47 |
1 files changed, 42 insertions, 5 deletions
diff --git a/Documentation/admin-guide/kernel-parameters.txt b/Documentation/admin-guide/kernel-parameters.txt index 756bfb7d5235..9725c546a0d4 100644 --- a/Documentation/admin-guide/kernel-parameters.txt +++ b/Documentation/admin-guide/kernel-parameters.txt @@ -1582,8 +1582,10 @@ registers. Default set by CONFIG_HPET_MMAP_DEFAULT. hugetlb_cma= [HW,CMA] The size of a CMA area used for allocation - of gigantic hugepages. - Format: nn[KMGTPE] + of gigantic hugepages. Or using node format, the size + of a CMA area per node can be specified. + Format: nn[KMGTPE] or (node format) + <node>:nn[KMGTPE][,<node>:nn[KMGTPE]] Reserve a CMA area of given size and allocate gigantic hugepages using the CMA allocator. If enabled, the @@ -1594,9 +1596,11 @@ the number of pages of hugepagesz to be allocated. If this is the first HugeTLB parameter on the command line, it specifies the number of pages to allocate for - the default huge page size. See also - Documentation/admin-guide/mm/hugetlbpage.rst. - Format: <integer> + the default huge page size. If using node format, the + number of pages to allocate per-node can be specified. + See also Documentation/admin-guide/mm/hugetlbpage.rst. + Format: <integer> or (node format) + <node>:<integer>[,<node>:<integer>] hugepagesz= [HW] The size of the HugeTLB pages. This is used in @@ -3249,6 +3253,19 @@ driver. A non-zero value sets the minimum interval in seconds between layoutstats transmissions. + nfsd.inter_copy_offload_enable = + [NFSv4.2] When set to 1, the server will support + server-to-server copies for which this server is + the destination of the copy. + + nfsd.nfsd4_ssc_umount_timeout = + [NFSv4.2] When used as the destination of a + server-to-server copy, knfsd temporarily mounts + the source server. It caches the mount in case + it will be needed again, and discards it if not + used for the number of milliseconds specified by + this parameter. + nfsd.nfs4_disable_idmapping= [NFSv4] When set to the default of '1', the NFSv4 server will return only numeric uids and gids to @@ -3256,6 +3273,7 @@ and gids from such clients. This is intended to ease migration from NFSv2/v3. + nmi_backtrace.backtrace_idle [KNL] Dump stacks even of idle CPUs in response to an NMI stack-backtrace request. @@ -4988,6 +5006,18 @@ an IOTLB flush. Default is lazy flushing before reuse, which is faster. + s390_iommu_aperture= [KNL,S390] + Specifies the size of the per device DMA address space + accessible through the DMA and IOMMU APIs as a decimal + factor of the size of main memory. + The default is 1 meaning that one can concurrently use + as many DMA addresses as physical memory is installed, + if supported by hardware, and thus map all of memory + once. With a value of 2 one can map all of memory twice + and so on. As a special case a factor of 0 imposes no + restrictions other than those given by hardware at the + cost of significant additional memory use for tables. + sa1100ir [NET] See drivers/net/irda/sa1100_ir.c. @@ -6363,6 +6393,13 @@ improve timer resolution at the expense of processing more timer interrupts. + xen.balloon_boot_timeout= [XEN] + The time (in seconds) to wait before giving up to boot + in case initial ballooning fails to free enough memory. + Applies only when running as HVM or PVH guest and + started with less memory configured than allowed at + max. Default is 180. + xen.event_eoi_delay= [XEN] How long to delay EOI handling in case of event storms (jiffies). Default is 10. |