diff options
| -rw-r--r-- | Documentation/driver-api/scsi.rst | 15 | ||||
| -rw-r--r-- | Documentation/scsi/scsi_mid_low_api.rst | 22 | ||||
| -rw-r--r-- | MAINTAINERS | 3 | ||||
| -rw-r--r-- | drivers/scsi/FlashPoint.c | 1 | ||||
| -rw-r--r-- | drivers/scsi/Kconfig | 4 | ||||
| -rw-r--r-- | drivers/scsi/aic7xxx/Kconfig.aic79xx | 75 | ||||
| -rw-r--r-- | drivers/scsi/aic7xxx/Kconfig.aic7xxx | 97 | ||||
| -rw-r--r-- | drivers/scsi/megaraid/Kconfig.megaraid | 113 | ||||
| -rw-r--r-- | drivers/scsi/qla2xxx/Kconfig | 42 | ||||
| -rw-r--r-- | drivers/scsi/scsi_debugfs.c | 56 | ||||
| -rw-r--r-- | drivers/scsi/snic/snic_attrs.c | 11 | ||||
| -rw-r--r-- | drivers/ufs/core/ufshcd.c | 169 | ||||
| -rw-r--r-- | drivers/ufs/host/ufs-exynos.c | 1 | ||||
| -rw-r--r-- | drivers/ufs/host/ufs-mediatek.c | 1 | ||||
| -rw-r--r-- | drivers/ufs/host/ufs-qcom.c | 3 | ||||
| -rw-r--r-- | include/scsi/iser.h | 2 | ||||
| -rw-r--r-- | include/scsi/libfcoe.h | 25 | ||||
| -rw-r--r-- | include/scsi/scsi.h | 7 | ||||
| -rw-r--r-- | include/scsi/scsi_cmnd.h | 2 | ||||
| -rw-r--r-- | include/scsi/scsi_transport_fc.h | 5 | ||||
| -rw-r--r-- | include/scsi/scsi_transport_srp.h | 4 | ||||
| -rw-r--r-- | include/ufs/ufshcd.h | 2 | ||||
| -rw-r--r-- | include/ufs/ufshci.h | 13 |
23 files changed, 269 insertions, 404 deletions
diff --git a/Documentation/driver-api/scsi.rst b/Documentation/driver-api/scsi.rst index 64b231d125e0..332c54683006 100644 --- a/Documentation/driver-api/scsi.rst +++ b/Documentation/driver-api/scsi.rst @@ -20,7 +20,7 @@ Although the old parallel (fast/wide/ultra) SCSI bus has largely fallen out of use, the SCSI command set is more widely used than ever to communicate with devices over a number of different busses. -The `SCSI protocol <http://www.t10.org/scsi-3.htm>`__ is a big-endian +The `SCSI protocol <https://www.t10.org/scsi-3.htm>`__ is a big-endian peer-to-peer packet based protocol. SCSI commands are 6, 10, 12, or 16 bytes long, often followed by an associated data payload. @@ -28,8 +28,7 @@ SCSI commands can be transported over just about any kind of bus, and are the default protocol for storage devices attached to USB, SATA, SAS, Fibre Channel, FireWire, and ATAPI devices. SCSI packets are also commonly exchanged over Infiniband, -`I2O <http://i2o.shadowconnect.com/faq.php>`__, TCP/IP -(`iSCSI <https://en.wikipedia.org/wiki/ISCSI>`__), even `Parallel +TCP/IP (`iSCSI <https://en.wikipedia.org/wiki/ISCSI>`__), even `Parallel ports <http://cyberelk.net/tim/parport/parscsi.html>`__. Design of the Linux SCSI subsystem @@ -170,9 +169,9 @@ drivers/scsi/scsi_netlink.c Infrastructure to provide async events from transports to userspace via netlink, using a single NETLINK_SCSITRANSPORT protocol for all -transports. See `the original patch -submission <http://marc.info/?l=linux-scsi&m=115507374832500&w=2>`__ for -more details. +transports. See `the original patch submission +<https://lore.kernel.org/linux-scsi/[email protected]/>`__ +for more details. .. kernel-doc:: drivers/scsi/scsi_netlink.c :internal: @@ -328,11 +327,11 @@ the ordinary is seen. To be more realistic, the simulated devices have the transport attributes of SAS disks. -For documentation see http://sg.danny.cz/sg/sdebug26.html +For documentation see http://sg.danny.cz/sg/scsi_debug.html todo ~~~~ Parallel (fast/wide/ultra) SCSI, USB, SATA, SAS, Fibre Channel, -FireWire, ATAPI devices, Infiniband, I2O, Parallel ports, +FireWire, ATAPI devices, Infiniband, Parallel ports, netlink... diff --git a/Documentation/scsi/scsi_mid_low_api.rst b/Documentation/scsi/scsi_mid_low_api.rst index 022198c51350..2df29b92e196 100644 --- a/Documentation/scsi/scsi_mid_low_api.rst +++ b/Documentation/scsi/scsi_mid_low_api.rst @@ -42,18 +42,18 @@ This version of the document roughly matches linux kernel version 2.6.8 . Documentation ============= There is a SCSI documentation directory within the kernel source tree, -typically Documentation/scsi . Most documents are in plain -(i.e. ASCII) text. This file is named scsi_mid_low_api.txt and can be +typically Documentation/scsi . Most documents are in reStructuredText +format. This file is named scsi_mid_low_api.rst and can be found in that directory. A more recent copy of this document may be found -at http://web.archive.org/web/20070107183357rn_1/sg.torque.net/scsi/. -Many LLDs are documented there (e.g. aic7xxx.txt). The SCSI mid-level is -briefly described in scsi.txt which contains a url to a document -describing the SCSI subsystem in the lk 2.4 series. Two upper level -drivers have documents in that directory: st.txt (SCSI tape driver) and -scsi-generic.txt (for the sg driver). - -Some documentation (or urls) for LLDs may be found in the C source code -or in the same directory as the C source code. For example to find a url +at https://docs.kernel.org/scsi/scsi_mid_low_api.html. Many LLDs are +documented in Documentation/scsi (e.g. aic7xxx.rst). The SCSI mid-level is +briefly described in scsi.rst which contains a URL to a document describing +the SCSI subsystem in the Linux Kernel 2.4 series. Two upper level +drivers have documents in that directory: st.rst (SCSI tape driver) and +scsi-generic.rst (for the sg driver). + +Some documentation (or URLs) for LLDs may be found in the C source code +or in the same directory as the C source code. For example to find a URL about the USB mass storage driver see the /usr/src/linux/drivers/usb/storage directory. diff --git a/MAINTAINERS b/MAINTAINERS index aa3b947fb080..7edba21309cd 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -5781,10 +5781,9 @@ F: include/uapi/misc/cxl.h CXLFLASH (IBM Coherent Accelerator Processor Interface CAPI Flash) SCSI DRIVER M: Manoj N. Kumar <[email protected]> -M: Matthew R. Ochs <[email protected]> M: Uma Krishnan <[email protected]> -S: Supported +S: Obsolete F: Documentation/arch/powerpc/cxlflash.rst F: drivers/scsi/cxlflash/ F: include/uapi/scsi/cxlflash_ioctl.h diff --git a/drivers/scsi/FlashPoint.c b/drivers/scsi/FlashPoint.c index 3d9c56ac8224..9e77b8e1ea7c 100644 --- a/drivers/scsi/FlashPoint.c +++ b/drivers/scsi/FlashPoint.c @@ -2631,7 +2631,6 @@ static void FPT_sres(u32 port, unsigned char p_card, WRW_HARPOON((port + hp_fiforead), (unsigned short)0x00); our_target = (unsigned char)(RD_HARPOON(port + hp_select_id) >> 4); - currTar_Info = &FPT_sccbMgrTbl[p_card][our_target]; msgRetryCount = 0; do { diff --git a/drivers/scsi/Kconfig b/drivers/scsi/Kconfig index 634f2f501c6c..065db86d6021 100644 --- a/drivers/scsi/Kconfig +++ b/drivers/scsi/Kconfig @@ -53,7 +53,7 @@ config SCSI_ESP_PIO config SCSI_NETLINK bool - default n + default n depends on NET config SCSI_PROC_FS @@ -327,7 +327,7 @@ config ISCSI_TCP config ISCSI_BOOT_SYSFS tristate "iSCSI Boot Sysfs Interface" - default n + default n help This option enables support for exposing iSCSI boot information via sysfs to userspace. If you wish to export this information, diff --git a/drivers/scsi/aic7xxx/Kconfig.aic79xx b/drivers/scsi/aic7xxx/Kconfig.aic79xx index 4bc53eec4c83..863f0932ef59 100644 --- a/drivers/scsi/aic7xxx/Kconfig.aic79xx +++ b/drivers/scsi/aic7xxx/Kconfig.aic79xx @@ -8,79 +8,80 @@ config SCSI_AIC79XX depends on PCI && HAS_IOPORT && SCSI select SCSI_SPI_ATTRS help - This driver supports all of Adaptec's Ultra 320 PCI-X - based SCSI controllers. + This driver supports all of Adaptec's Ultra 320 PCI-X + based SCSI controllers. config AIC79XX_CMDS_PER_DEVICE int "Maximum number of TCQ commands per device" depends on SCSI_AIC79XX default "32" help - Specify the number of commands you would like to allocate per SCSI - device when Tagged Command Queueing (TCQ) is enabled on that device. + Specify the number of commands you would like to allocate per SCSI + device when Tagged Command Queueing (TCQ) is enabled on that device. - This is an upper bound value for the number of tagged transactions - to be used for any device. The aic7xxx driver will automatically - vary this number based on device behavior. For devices with a - fixed maximum, the driver will eventually lock to this maximum - and display a console message indicating this value. + This is an upper bound value for the number of tagged transactions + to be used for any device. The aic7xxx driver will automatically + vary this number based on device behavior. For devices with a + fixed maximum, the driver will eventually lock to this maximum + and display a console message indicating this value. - Due to resource allocation issues in the Linux SCSI mid-layer, using - a high number of commands per device may result in memory allocation - failures when many devices are attached to the system. For this reason, - the default is set to 32. Higher values may result in higher performance - on some devices. The upper bound is 253. 0 disables tagged queueing. + Due to resource allocation issues in the Linux SCSI mid-layer, using + a high number of commands per device may result in memory allocation + failures when many devices are attached to the system. For this + reason, the default is set to 32. Higher values may result in higher + performance on some devices. The upper bound is 253. 0 disables + tagged queueing. - Per device tag depth can be controlled via the kernel command line - "tag_info" option. See Documentation/scsi/aic79xx.rst for details. + Per device tag depth can be controlled via the kernel command line + "tag_info" option. See Documentation/scsi/aic79xx.rst for details. config AIC79XX_RESET_DELAY_MS int "Initial bus reset delay in milli-seconds" depends on SCSI_AIC79XX default "5000" help - The number of milliseconds to delay after an initial bus reset. - The bus settle delay following all error recovery actions is - dictated by the SCSI layer and is not affected by this value. + The number of milliseconds to delay after an initial bus reset. + The bus settle delay following all error recovery actions is + dictated by the SCSI layer and is not affected by this value. - Default: 5000 (5 seconds) + Default: 5000 (5 seconds) config AIC79XX_BUILD_FIRMWARE bool "Build Adapter Firmware with Kernel Build" depends on SCSI_AIC79XX && !PREVENT_FIRMWARE_BUILD help - This option should only be enabled if you are modifying the firmware - source to the aic79xx driver and wish to have the generated firmware - include files updated during a normal kernel build. The assembler - for the firmware requires lex and yacc or their equivalents, as well - as the db v1 library. You may have to install additional packages - or modify the assembler Makefile or the files it includes if your - build environment is different than that of the author. + This option should only be enabled if you are modifying the firmware + source to the aic79xx driver and wish to have the generated firmware + include files updated during a normal kernel build. The assembler + for the firmware requires lex and yacc or their equivalents, as well + as the db v1 library. You may have to install additional packages + or modify the assembler Makefile or the files it includes if your + build environment is different than that of the author. config AIC79XX_DEBUG_ENABLE bool "Compile in Debugging Code" depends on SCSI_AIC79XX default y help - Compile in aic79xx debugging code that can be useful in diagnosing - driver errors. + Compile in aic79xx debugging code that can be useful in diagnosing + driver errors. config AIC79XX_DEBUG_MASK int "Debug code enable mask (16383 for all debugging)" depends on SCSI_AIC79XX default "0" help - Bit mask of debug options that is only valid if the - CONFIG_AIC79XX_DEBUG_ENABLE option is enabled. The bits in this mask - are defined in the drivers/scsi/aic7xxx/aic79xx.h - search for the - variable ahd_debug in that file to find them. + Bit mask of debug options that is only valid if the + CONFIG_AIC79XX_DEBUG_ENABLE option is enabled. The bits in this mask + are defined in the drivers/scsi/aic7xxx/aic79xx.h - search for the + variable ahd_debug in that file to find them. config AIC79XX_REG_PRETTY_PRINT bool "Decode registers during diagnostics" depends on SCSI_AIC79XX default y help - Compile in register value tables for the output of expanded register - contents in diagnostics. This make it much easier to understand debug - output without having to refer to a data book and/or the aic7xxx.reg - file. + Compile in register value tables for the output of expanded register + contents in diagnostics. This make it much easier to understand debug + output without having to refer to a data book and/or the aic7xxx.reg + file. diff --git a/drivers/scsi/aic7xxx/Kconfig.aic7xxx b/drivers/scsi/aic7xxx/Kconfig.aic7xxx index f0425145a5f4..8f87f2d8ba9f 100644 --- a/drivers/scsi/aic7xxx/Kconfig.aic7xxx +++ b/drivers/scsi/aic7xxx/Kconfig.aic7xxx @@ -8,84 +8,85 @@ config SCSI_AIC7XXX depends on (PCI || EISA) && HAS_IOPORT && SCSI select SCSI_SPI_ATTRS help - This driver supports all of Adaptec's Fast through Ultra 160 PCI - based SCSI controllers as well as the aic7770 based EISA and VLB - SCSI controllers (the 274x and 284x series). For AAA and ARO based - configurations, only SCSI functionality is provided. + This driver supports all of Adaptec's Fast through Ultra 160 PCI + based SCSI controllers as well as the aic7770 based EISA and VLB + SCSI controllers (the 274x and 284x series). For AAA and ARO based + configurations, only SCSI functionality is provided. - To compile this driver as a module, choose M here: the - module will be called aic7xxx. + To compile this driver as a module, choose M here: the + module will be called aic7xxx. config AIC7XXX_CMDS_PER_DEVICE int "Maximum number of TCQ commands per device" depends on SCSI_AIC7XXX default "32" help - Specify the number of commands you would like to allocate per SCSI - device when Tagged Command Queueing (TCQ) is enabled on that device. + Specify the number of commands you would like to allocate per SCSI + device when Tagged Command Queueing (TCQ) is enabled on that device. - This is an upper bound value for the number of tagged transactions - to be used for any device. The aic7xxx driver will automatically - vary this number based on device behavior. For devices with a - fixed maximum, the driver will eventually lock to this maximum - and display a console message indicating this value. + This is an upper bound value for the number of tagged transactions + to be used for any device. The aic7xxx driver will automatically + vary this number based on device behavior. For devices with a + fixed maximum, the driver will eventually lock to this maximum + and display a console message indicating this value. - Due to resource allocation issues in the Linux SCSI mid-layer, using - a high number of commands per device may result in memory allocation - failures when many devices are attached to the system. For this reason, - the default is set to 32. Higher values may result in higher performance - on some devices. The upper bound is 253. 0 disables tagged queueing. + Due to resource allocation issues in the Linux SCSI mid-layer, using + a high number of commands per device may result in memory allocation + failures when many devices are attached to the system. For this + reason, the default is set to 32. Higher values may result in higher + performance on some devices. The upper bound is 253. 0 disables tagged + queueing. - Per device tag depth can be controlled via the kernel command line - "tag_info" option. See Documentation/scsi/aic7xxx.rst for details. + Per device tag depth can be controlled via the kernel command line + "tag_info" option. See Documentation/scsi/aic7xxx.rst for details. config AIC7XXX_RESET_DELAY_MS int "Initial bus reset delay in milli-seconds" depends on SCSI_AIC7XXX default "5000" help - The number of milliseconds to delay after an initial bus reset. - The bus settle delay following all error recovery actions is - dictated by the SCSI layer and is not affected by this value. + The number of milliseconds to delay after an initial bus reset. + The bus settle delay following all error recovery actions is + dictated by the SCSI layer and is not affected by this value. - Default: 5000 (5 seconds) + Default: 5000 (5 seconds) config AIC7XXX_BUILD_FIRMWARE bool "Build Adapter Firmware with Kernel Build" depends on SCSI_AIC7XXX && !PREVENT_FIRMWARE_BUILD help - This option should only be enabled if you are modifying the firmware - source to the aic7xxx driver and wish to have the generated firmware - include files updated during a normal kernel build. The assembler - for the firmware requires lex and yacc or their equivalents, as well - as the db v1 library. You may have to install additional packages - or modify the assembler Makefile or the files it includes if your - build environment is different than that of the author. + This option should only be enabled if you are modifying the firmware + source to the aic7xxx driver and wish to have the generated firmware + include files updated during a normal kernel build. The assembler + for the firmware requires lex and yacc or their equivalents, as well + as the db v1 library. You may have to install additional packages + or modify the assembler Makefile or the files it includes if your + build environment is different than that of the author. config AIC7XXX_DEBUG_ENABLE bool "Compile in Debugging Code" depends on SCSI_AIC7XXX default y help - Compile in aic7xxx debugging code that can be useful in diagnosing - driver errors. + Compile in aic7xxx debugging code that can be useful in diagnosing + driver errors. config AIC7XXX_DEBUG_MASK - int "Debug code enable mask (2047 for all debugging)" - depends on SCSI_AIC7XXX - default "0" - help - Bit mask of debug options that is only valid if the - CONFIG_AIC7XXX_DEBUG_ENABLE option is enabled. The bits in this mask - are defined in the drivers/scsi/aic7xxx/aic7xxx.h - search for the - variable ahc_debug in that file to find them. + int "Debug code enable mask (2047 for all debugging)" + depends on SCSI_AIC7XXX + default "0" + help + Bit mask of debug options that is only valid if the + CONFIG_AIC7XXX_DEBUG_ENABLE option is enabled. The bits in this mask + are defined in the drivers/scsi/aic7xxx/aic7xxx.h - search for the + variable ahc_debug in that file to find them. config AIC7XXX_REG_PRETTY_PRINT - bool "Decode registers during diagnostics" - depends on SCSI_AIC7XXX + bool "Decode registers during diagnostics" + depends on SCSI_AIC7XXX default y - help - Compile in register value tables for the output of expanded register - contents in diagnostics. This make it much easier to understand debug - output without having to refer to a data book and/or the aic7xxx.reg - file. + help + Compile in register value tables for the output of expanded register + contents in diagnostics. This make it much easier to understand debug + output without having to refer to a data book and/or the aic7xxx.reg + file. diff --git a/drivers/scsi/megaraid/Kconfig.megaraid b/drivers/scsi/megaraid/Kconfig.megaraid index 3f2ce1eb081c..56b76d73895b 100644 --- a/drivers/scsi/megaraid/Kconfig.megaraid +++ b/drivers/scsi/megaraid/Kconfig.megaraid @@ -3,85 +3,84 @@ config MEGARAID_NEWGEN bool "LSI Logic New Generation RAID Device Drivers" depends on PCI && HAS_IOPORT && SCSI help - LSI Logic RAID Device Drivers + LSI Logic RAID Device Drivers config MEGARAID_MM tristate "LSI Logic Management Module (New Driver)" depends on PCI && HAS_IOPORT && SCSI && MEGARAID_NEWGEN help - Management Module provides ioctl, sysfs support for LSI Logic - RAID controllers. - To compile this driver as a module, choose M here: the - module will be called megaraid_mm + Management Module provides ioctl, sysfs support for LSI Logic + RAID controllers. + To compile this driver as a module, choose M here: the + module will be called megaraid_mm config MEGARAID_MAILBOX tristate "LSI Logic MegaRAID Driver (New Driver)" depends on PCI && SCSI && MEGARAID_MM help - List of supported controllers + List of supported controllers - OEM Product Name VID :DID :SVID:SSID - --- ------------ ---- ---- ---- ---- - Dell PERC3/QC 101E:1960:1028:0471 - Dell PERC3/DC 101E:1960:1028:0493 - Dell PERC3/SC 101E:1960:1028:0475 - Dell PERC3/Di 1028:000E:1028:0123 - Dell PERC4/SC 1000:1960:1028:0520 - Dell PERC4/DC 1000:1960:1028:0518 - Dell PERC4/QC 1000:0407:1028:0531 - Dell PERC4/Di 1028:000F:1028:014A - Dell PERC 4e/Si 1028:0013:1028:016c - Dell PERC 4e/Di 1028:0013:1028:016d - Dell PERC 4e/Di 1028:0013:1028:016e - Dell PERC 4e/Di 1028:0013:1028:016f - Dell PERC 4e/Di 1028:0013:1028:0170 - Dell PERC 4e/DC 1000:0408:1028:0002 - Dell PERC 4e/SC 1000:0408:1028:0001 - LSI MegaRAID SCSI 320-0 1000:1960:1000:A520 - LSI MegaRAID SCSI 320-1 1000:1960:1000:0520 - LSI MegaRAID SCSI 320-2 1000:1960:1000:0518 - LSI MegaRAID SCSI 320-0X 1000:0407:1000:0530 - LSI MegaRAID SCSI 320-2X 1000:0407:1000:0532 - LSI MegaRAID SCSI 320-4X 1000:0407:1000:0531 - LSI MegaRAID SCSI 320-1E 1000:0408:1000:0001 - LSI MegaRAID SCSI 320-2E 1000:0408:1000:0002 - LSI MegaRAID SATA 150-4 1000:1960:1000:4523 - LSI MegaRAID SATA 150-6 1000:1960:1000:0523 - LSI MegaRAID SATA 300-4X 1000:0409:1000:3004 - LSI MegaRAID SATA 300-8X 1000:0409:1000:3008 - INTEL RAID Controller SRCU42X 1000:0407:8086:0532 - INTEL RAID Controller SRCS16 1000:1960:8086:0523 - INTEL RAID Controller SRCU42E 1000:0408:8086:0002 - INTEL RAID Controller SRCZCRX 1000:0407:8086:0530 - INTEL RAID Controller SRCS28X 1000:0409:8086:3008 - INTEL RAID Controller SROMBU42E 1000:0408:8086:3431 - INTEL RAID Controller SROMBU42E 1000:0408:8086:3499 - INTEL RAID Controller SRCU51L 1000:1960:8086:0520 - FSC MegaRAID PCI Express ROMB 1000:0408:1734:1065 - ACER MegaRAID ROMB-2E 1000:0408:1025:004D - NEC MegaRAID PCI Express ROMB 1000:0408:1033:8287 + OEM Product Name VID :DID :SVID:SSID + --- ------------ ---- ---- ---- ---- + Dell PERC3/QC 101E:1960:1028:0471 + Dell PERC3/DC 101E:1960:1028:0493 + Dell PERC3/SC 101E:1960:1028:0475 + Dell PERC3/Di 1028:000E:1028:0123 + Dell PERC4/SC 1000:1960:1028:0520 + Dell PERC4/DC 1000:1960:1028:0518 + Dell PERC4/QC 1000:0407:1028:0531 + Dell PERC4/Di 1028:000F:1028:014A + Dell PERC 4e/Si 1028:0013:1028:016c + Dell PERC 4e/Di 1028:0013:1028:016d + Dell PERC 4e/Di 1028:0013:1028:016e + Dell PERC 4e/Di 1028:0013:1028:016f + Dell PERC 4e/Di 1028:0013:1028:0170 + Dell PERC 4e/DC 1000:0408:1028:0002 + Dell PERC 4e/SC 1000:0408:1028:0001 + LSI MegaRAID SCSI 320-0 1000:1960:1000:A520 + LSI MegaRAID SCSI 320-1 1000:1960:1000:0520 + LSI MegaRAID SCSI 320-2 1000:1960:1000:0518 + LSI MegaRAID SCSI 320-0X 1000:0407:1000:0530 + LSI MegaRAID SCSI 320-2X 1000:0407:1000:0532 + LSI MegaRAID SCSI 320-4X 1000:0407:1000:0531 + LSI MegaRAID SCSI 320-1E 1000:0408:1000:0001 + LSI MegaRAID SCSI 320-2E 1000:0408:1000:0002 + LSI MegaRAID SATA 150-4 1000:1960:1000:4523 + LSI MegaRAID SATA 150-6 1000:1960:1000:0523 + LSI MegaRAID SATA 300-4X 1000:0409:1000:3004 + LSI MegaRAID SATA 300-8X 1000:0409:1000:3008 + INTEL RAID Controller SRCU42X 1000:0407:8086:0532 + INTEL RAID Controller SRCS16 1000:1960:8086:0523 + INTEL RAID Controller SRCU42E 1000:0408:8086:0002 + INTEL RAID Controller SRCZCRX 1000:0407:8086:0530 + INTEL RAID Controller SRCS28X 1000:0409:8086:3008 + INTEL RAID Controller SROMBU42E 1000:0408:8086:3431 + INTEL RAID Controller SROMBU42E 1000:0408:8086:3499 + INTEL RAID Controller SRCU51L 1000:1960:8086:0520 + FSC MegaRAID PCI Express ROMB 1000:0408:1734:1065 + ACER MegaRAID ROMB-2E 1000:0408:1025:004D + NEC MegaRAID PCI Express ROMB 1000:0408:1033:8287 - To compile this driver as a module, choose M here: the - module will be called megaraid_mbox + To compile this driver as a module, choose M here: the + module will be called megaraid_mbox config MEGARAID_LEGACY tristate "LSI Logic Legacy MegaRAID Driver" depends on PCI && HAS_IOPORT && SCSI help - This driver supports the LSI MegaRAID 418, 428, 438, 466, 762, 490 - and 467 SCSI host adapters. This driver also support the all U320 - RAID controllers + This driver supports the LSI MegaRAID 418, 428, 438, 466, 762, 490 + and 467 SCSI host adapters. This driver also support the all U320 + RAID controllers - To compile this driver as a module, choose M here: the - module will be called megaraid + To compile this driver as a module, choose M here: the + module will be called megaraid config MEGARAID_SAS tristate "LSI Logic MegaRAID SAS RAID Module" depends on PCI && SCSI select IRQ_POLL help - Module for LSI Logic's SAS based RAID controllers. - To compile this driver as a module, choose 'm' here. - Module will be called megaraid_sas - + Module for LSI Logic's SAS based RAID controllers. + To compile this driver as a module, choose 'm' here. + Module will be called megaraid_sas diff --git a/drivers/scsi/qla2xxx/Kconfig b/drivers/scsi/qla2xxx/Kconfig index a584708d3056..a8b4314bfd6e 100644 --- a/drivers/scsi/qla2xxx/Kconfig +++ b/drivers/scsi/qla2xxx/Kconfig @@ -7,29 +7,29 @@ config SCSI_QLA_FC select FW_LOADER select BTREE help - This qla2xxx driver supports all QLogic Fibre Channel - PCI and PCIe host adapters. + This qla2xxx driver supports all QLogic Fibre Channel + PCI and PCIe host adapters. - By default, firmware for the ISP parts will be loaded - via the Firmware Loader interface. + By default, firmware for the ISP parts will be loaded + via the Firmware Loader interface. - ISP Firmware Filename - ---------- ----------------- - 21xx ql2100_fw.bin - 22xx ql2200_fw.bin - 2300, 2312, 6312 ql2300_fw.bin - 2322, 6322 ql2322_fw.bin - 24xx, 54xx ql2400_fw.bin - 25xx ql2500_fw.bin + ISP Firmware Filename + ---------- ----------------- + 21xx ql2100_fw.bin + 22xx ql2200_fw.bin + 2300, 2312, 6312 ql2300_fw.bin + 2322, 6322 ql2322_fw.bin + 24xx, 54xx ql2400_fw.bin + 25xx ql2500_fw.bin - Upon request, the driver caches the firmware image until - the driver is unloaded. + Upon request, the driver caches the firmware image until + the driver is unloaded. - Firmware images can be retrieved from: + Firmware images can be retrieved from: - http://ldriver.qlogic.com/firmware/ + http://ldriver.qlogic.com/firmware/ - They are also included in the linux-firmware tree as well. + They are also included in the linux-firmware tree as well. config TCM_QLA2XXX tristate "TCM_QLA2XXX fabric module for QLogic 24xx+ series target mode HBAs" @@ -38,13 +38,15 @@ config TCM_QLA2XXX select BTREE default n help - Say Y here to enable the TCM_QLA2XXX fabric module for QLogic 24xx+ series target mode HBAs + Say Y here to enable the TCM_QLA2XXX fabric module for QLogic 24xx+ + series target mode HBAs. if TCM_QLA2XXX config TCM_QLA2XXX_DEBUG bool "TCM_QLA2XXX fabric module DEBUG mode for QLogic 24xx+ series target mode HBAs" default n help - Say Y here to enable the TCM_QLA2XXX fabric module DEBUG for QLogic 24xx+ series target mode HBAs - This will include code to enable the SCSI command jammer + Say Y here to enable the TCM_QLA2XXX fabric module DEBUG for + QLogic 24xx+ series target mode HBAs. + This will include code to enable the SCSI command jammer. endif diff --git a/drivers/scsi/scsi_debugfs.c b/drivers/scsi/scsi_debugfs.c index f795848b316c..eb52e39f37c9 100644 --- a/drivers/scsi/scsi_debugfs.c +++ b/drivers/scsi/scsi_debugfs.c @@ -1,5 +1,6 @@ // SPDX-License-Identifier: GPL-2.0 #include <linux/bitops.h> +#include <linux/cleanup.h> #include <linux/seq_file.h> #include <scsi/scsi_cmnd.h> #include <scsi/scsi_dbg.h> @@ -32,38 +33,43 @@ static int scsi_flags_show(struct seq_file *m, const unsigned long flags, return 0; } -void scsi_show_rq(struct seq_file *m, struct request *rq) +static const char *scsi_cmd_list_info(struct scsi_cmnd *cmd) { - struct scsi_cmnd *cmd = blk_mq_rq_to_pdu(rq), *cmd2; struct Scsi_Host *shost = cmd->device->host; + struct scsi_cmnd *cmd2; + + guard(spinlock_irq)(shost->host_lock); + + list_for_each_entry(cmd2, &shost->eh_abort_list, eh_entry) + if (cmd == cmd2) + return "on eh_abort_list"; + + list_for_each_entry(cmd2, &shost->eh_cmd_q, eh_entry) + if (cmd == cmd2) + return "on eh_cmd_q"; + + return NULL; +} + +void scsi_show_rq(struct seq_file *m, struct request *rq) +{ + struct scsi_cmnd *cmd = blk_mq_rq_to_pdu(rq); int alloc_ms = jiffies_to_msecs(jiffies - cmd->jiffies_at_alloc); int timeout_ms = jiffies_to_msecs(rq->timeout); - const char *list_info = NULL; char buf[80] = "(?)"; - spin_lock_irq(shost->host_lock); - list_for_each_entry(cmd2, &shost->eh_abort_list, eh_entry) { - if (cmd == cmd2) { - list_info = "on eh_abort_list"; - goto unlock; - } - } - list_for_each_entry(cmd2, &shost->eh_cmd_q, eh_entry) { - if (cmd == cmd2) { - list_info = "on eh_cmd_q"; - goto unlock; - } - } -unlock: - spin_unlock_irq(shost->host_lock); + if (cmd->flags & SCMD_INITIALIZED) { + const char *list_info = scsi_cmd_list_info(cmd); - __scsi_format_command(buf, sizeof(buf), cmd->cmnd, cmd->cmd_len); - seq_printf(m, ", .cmd=%s, .retries=%d, .allowed=%d, .result = %#x, %s%s.flags=", - buf, cmd->retries, cmd->allowed, cmd->result, - list_info ? : "", list_info ? ", " : ""); + __scsi_format_command(buf, sizeof(buf), cmd->cmnd, cmd->cmd_len); + seq_printf(m, ", .cmd=%s, .retries=%d, .allowed=%d, .result = %#x%s%s", + buf, cmd->retries, cmd->allowed, cmd->result, + list_info ? ", " : "", list_info ? : ""); + seq_printf(m, ", .timeout=%d.%03d, allocated %d.%03d s ago", + timeout_ms / 1000, timeout_ms % 1000, + alloc_ms / 1000, alloc_ms % 1000); + } + seq_printf(m, ", .flags="); scsi_flags_show(m, cmd->flags, scsi_cmd_flags, ARRAY_SIZE(scsi_cmd_flags)); - seq_printf(m, ", .timeout=%d.%03d, allocated %d.%03d s ago", - timeout_ms / 1000, timeout_ms % 1000, - alloc_ms / 1000, alloc_ms % 1000); } diff --git a/drivers/scsi/snic/snic_attrs.c b/drivers/scsi/snic/snic_attrs.c index 3ddbdbc3ded1..48bf82d042b4 100644 --- a/drivers/scsi/snic/snic_attrs.c +++ b/drivers/scsi/snic/snic_attrs.c @@ -13,7 +13,7 @@ snic_show_sym_name(struct device *dev, { struct snic *snic = shost_priv(class_to_shost(dev)); - return snprintf(buf, PAGE_SIZE, "%s\n", snic->name); + return sysfs_emit(buf, "%s\n", snic->name); } static ssize_t @@ -23,8 +23,7 @@ snic_show_state(struct device *dev, { struct snic *snic = shost_priv(class_to_shost(dev)); - return snprintf(buf, PAGE_SIZE, "%s\n", - snic_state_str[snic_get_state(snic)]); + return sysfs_emit(buf, "%s\n", snic_state_str[snic_get_state(snic)]); } static ssize_t @@ -32,7 +31,7 @@ snic_show_drv_version(struct device *dev, struct device_attribute *attr, char *buf) { - return snprintf(buf, PAGE_SIZE, "%s\n", SNIC_DRV_VERSION); + return sysfs_emit(buf, "%s\n", SNIC_DRV_VERSION); } static ssize_t @@ -45,8 +44,8 @@ snic_show_link_state(struct device *dev, if (snic->config.xpt_type == SNIC_DAS) snic->link_status = svnic_dev_link_status(snic->vdev); - return snprintf(buf, PAGE_SIZE, "%s\n", - (snic->link_status) ? "Link Up" : "Link Down"); + return sysfs_emit(buf, "%s\n", + (snic->link_status) ? "Link Up" : "Link Down"); } static DEVICE_ATTR(snic_sym_name, S_IRUGO, snic_show_sym_name, NULL); diff --git a/drivers/ufs/core/ufshcd.c b/drivers/ufs/core/ufshcd.c index 83227c870859..0819ddafe7a6 100644 --- a/drivers/ufs/core/ufshcd.c +++ b/drivers/ufs/core/ufshcd.c @@ -748,8 +748,6 @@ static int ufshcd_wait_for_register(struct ufs_hba *hba, u32 reg, u32 mask, */ static inline u32 ufshcd_get_intr_mask(struct ufs_hba *hba) { - if (hba->ufs_version == ufshci_version(1, 0)) - return INTERRUPT_MASK_ALL_VER_10; if (hba->ufs_version <= ufshci_version(2, 0)) return INTERRUPT_MASK_ALL_VER_11; @@ -990,30 +988,6 @@ bool ufshcd_is_hba_active(struct ufs_hba *hba) } EXPORT_SYMBOL_GPL(ufshcd_is_hba_active); -u32 ufshcd_get_local_unipro_ver(struct ufs_hba *hba) -{ - /* HCI version 1.0 and 1.1 supports UniPro 1.41 */ - if (hba->ufs_version <= ufshci_version(1, 1)) - return UFS_UNIPRO_VER_1_41; - else - return UFS_UNIPRO_VER_1_6; -} -EXPORT_SYMBOL(ufshcd_get_local_unipro_ver); - -static bool ufshcd_is_unipro_pa_params_tuning_req(struct ufs_hba *hba) -{ - /* - * If both host and device support UniPro ver1.6 or later, PA layer - * parameters tuning happens during link startup itself. - * - * We can manually tune PA layer parameters if either host or device - * doesn't support UniPro ver 1.6 or later. But to keep manual tuning - * logic simple, we will only do manual tuning if local unipro version - * doesn't support ver1.6 or later. - */ - return ufshcd_get_local_unipro_ver(hba) < UFS_UNIPRO_VER_1_6; -} - /** * ufshcd_pm_qos_init - initialize PM QoS request * @hba: per adapter instance @@ -2674,14 +2648,7 @@ static void ufshcd_enable_intr(struct ufs_hba *hba, u32 intrs) { u32 set = ufshcd_readl(hba, REG_INTERRUPT_ENABLE); - if (hba->ufs_version == ufshci_version(1, 0)) { - u32 rw; - rw = set & INTERRUPT_MASK_RW_VER_10; - set = rw | ((set ^ intrs) & intrs); - } else { - set |= intrs; - } - + set |= intrs; ufshcd_writel(hba, set, REG_INTERRUPT_ENABLE); } @@ -2694,16 +2661,7 @@ static void ufshcd_disable_intr(struct ufs_hba *hba, u32 intrs) { u32 set = ufshcd_readl(hba, REG_INTERRUPT_ENABLE); - if (hba->ufs_version == ufshci_version(1, 0)) { - u32 rw; - rw = (set & INTERRUPT_MASK_RW_VER_10) & - ~(intrs & INTERRUPT_MASK_RW_VER_10); - set = rw | ((set & intrs) & ~INTERRUPT_MASK_RW_VER_10); - - } else { - set &= ~intrs; - } - + set &= ~intrs; ufshcd_writel(hba, set, REG_INTERRUPT_ENABLE); } @@ -2715,21 +2673,17 @@ static void ufshcd_disable_intr(struct ufs_hba *hba, u32 intrs) * @upiu_flags: flags required in the header * @cmd_dir: requests data direction * @ehs_length: Total EHS Length (in 32‐bytes units of all Extra Header Segments) - * @legacy_type: UTP_CMD_TYPE_SCSI or UTP_CMD_TYPE_DEV_MANAGE */ static void ufshcd_prepare_req_desc_hdr(struct ufs_hba *hba, struct ufshcd_lrb *lrbp, u8 *upiu_flags, enum dma_data_direction cmd_dir, - int ehs_length, enum utp_cmd_type legacy_type) + int ehs_length) { struct utp_transfer_req_desc *req_desc = lrbp->utr_descriptor_ptr; struct request_desc_header *h = &req_desc->header; enum utp_data_direction data_direction; - if (hba->ufs_version <= ufshci_version(1, 1)) - lrbp->command_type = legacy_type; - else - lrbp->command_type = UTP_CMD_TYPE_UFS_STORAGE; + lrbp->command_type = UTP_CMD_TYPE_UFS_STORAGE; *h = (typeof(*h)){ }; @@ -2863,7 +2817,7 @@ static int ufshcd_compose_devman_upiu(struct ufs_hba *hba, u8 upiu_flags; int ret = 0; - ufshcd_prepare_req_desc_hdr(hba, lrbp, &upiu_flags, DMA_NONE, 0, UTP_CMD_TYPE_DEV_MANAGE); + ufshcd_prepare_req_desc_hdr(hba, lrbp, &upiu_flags, DMA_NONE, 0); if (hba->dev_cmd.type == DEV_CMD_TYPE_QUERY) ufshcd_prepare_utp_query_req_upiu(hba, lrbp, upiu_flags); @@ -2887,8 +2841,7 @@ static void ufshcd_comp_scsi_upiu(struct ufs_hba *hba, struct ufshcd_lrb *lrbp) unsigned int ioprio_class = IOPRIO_PRIO_CLASS(req_get_ioprio(rq)); u8 upiu_flags; - ufshcd_prepare_req_desc_hdr(hba, lrbp, &upiu_flags, - lrbp->cmd->sc_data_direction, 0, UTP_CMD_TYPE_SCSI); + ufshcd_prepare_req_desc_hdr(hba, lrbp, &upiu_flags, lrbp->cmd->sc_data_direction, 0); if (ioprio_class == IOPRIO_CLASS_RT) upiu_flags |= UPIU_CMD_FLAGS_CP; ufshcd_prepare_utp_scsi_cmd_upiu(lrbp, upiu_flags); @@ -3088,16 +3041,7 @@ static int ufshcd_compose_dev_cmd(struct ufs_hba *hba, */ bool ufshcd_cmd_inflight(struct scsi_cmnd *cmd) { - struct request *rq; - - if (!cmd) - return false; - - rq = scsi_cmd_to_rq(cmd); - if (!blk_mq_request_started(rq)) - return false; - - return true; + return cmd && blk_mq_rq_state(scsi_cmd_to_rq(cmd)) == MQ_RQ_IN_FLIGHT; } /* @@ -5556,15 +5500,12 @@ void ufshcd_compl_one_cqe(struct ufs_hba *hba, int task_tag, ufshcd_release_scsi_cmd(hba, lrbp); /* Do not touch lrbp after scsi done */ scsi_done(cmd); - } else if (lrbp->command_type == UTP_CMD_TYPE_DEV_MANAGE || - lrbp->command_type == UTP_CMD_TYPE_UFS_STORAGE) { - if (hba->dev_cmd.complete) { - if (cqe) { - ocs = le32_to_cpu(cqe->status) & MASK_OCS; - lrbp->utr_descriptor_ptr->header.ocs = ocs; - } - complete(hba->dev_cmd.complete); + } else if (hba->dev_cmd.complete) { + if (cqe) { + ocs = le32_to_cpu(cqe->status) & MASK_OCS; + lrbp->utr_descriptor_ptr->header.ocs = ocs; } + complete(hba->dev_cmd.complete); } } @@ -7217,7 +7158,7 @@ static int ufshcd_issue_devman_upiu_cmd(struct ufs_hba *hba, ufshcd_setup_dev_cmd(hba, lrbp, cmd_type, 0, tag); - ufshcd_prepare_req_desc_hdr(hba, lrbp, &upiu_flags, DMA_NONE, 0, UTP_CMD_TYPE_DEV_MANAGE); + ufshcd_prepare_req_desc_hdr(hba, lrbp, &upiu_flags, DMA_NONE, 0); /* update the task tag in the request upiu */ req_upiu->header.task_tag = tag; @@ -7369,7 +7310,7 @@ int ufshcd_advanced_rpmb_req_handler(struct ufs_hba *hba, struct utp_upiu_req *r ufshcd_setup_dev_cmd(hba, lrbp, DEV_CMD_TYPE_RPMB, UFS_UPIU_RPMB_WLUN, tag); - ufshcd_prepare_req_desc_hdr(hba, lrbp, &upiu_flags, DMA_NONE, ehs, UTP_CMD_TYPE_DEV_MANAGE); + ufshcd_prepare_req_desc_hdr(hba, lrbp, &upiu_flags, DMA_NONE, ehs); /* update the task tag */ req_upiu->header.task_tag = tag; @@ -8357,83 +8298,6 @@ static void ufs_put_device_desc(struct ufs_hba *hba) } /** - * ufshcd_tune_pa_tactivate - Tunes PA_TActivate of local UniPro - * @hba: per-adapter instance - * - * PA_TActivate parameter can be tuned manually if UniPro version is less than - * 1.61. PA_TActivate needs to be greater than or equal to peerM-PHY's - * RX_MIN_ACTIVATETIME_CAPABILITY attribute. This optimal value can help reduce - * the hibern8 exit latency. - * - * Return: zero on success, non-zero error value on failure. - */ -static int ufshcd_tune_pa_tactivate(struct ufs_hba *hba) -{ - int ret = 0; - u32 peer_rx_min_activatetime = 0, tuned_pa_tactivate; - - ret = ufshcd_dme_peer_get(hba, - UIC_ARG_MIB_SEL( - RX_MIN_ACTIVATETIME_CAPABILITY, - UIC_ARG_MPHY_RX_GEN_SEL_INDEX(0)), - &peer_rx_min_activatetime); - if (ret) - goto out; - - /* make sure proper unit conversion is applied */ - tuned_pa_tactivate = - ((peer_rx_min_activatetime * RX_MIN_ACTIVATETIME_UNIT_US) - / PA_TACTIVATE_TIME_UNIT_US); - ret = ufshcd_dme_set(hba, UIC_ARG_MIB(PA_TACTIVATE), - tuned_pa_tactivate); - -out: - return ret; -} - -/** - * ufshcd_tune_pa_hibern8time - Tunes PA_Hibern8Time of local UniPro - * @hba: per-adapter instance - * - * PA_Hibern8Time parameter can be tuned manually if UniPro version is less than - * 1.61. PA_Hibern8Time needs to be maximum of local M-PHY's - * TX_HIBERN8TIME_CAPABILITY & peer M-PHY's RX_HIBERN8TIME_CAPABILITY. - * This optimal value can help reduce the hibern8 exit latency. - * - * Return: zero on success, non-zero error value on failure. - */ -static int ufshcd_tune_pa_hibern8time(struct ufs_hba *hba) -{ - int ret = 0; - u32 local_tx_hibern8_time_cap = 0, peer_rx_hibern8_time_cap = 0; - u32 max_hibern8_time, tuned_pa_hibern8time; - - ret = ufshcd_dme_get(hba, - UIC_ARG_MIB_SEL(TX_HIBERN8TIME_CAPABILITY, - UIC_ARG_MPHY_TX_GEN_SEL_INDEX(0)), - &local_tx_hibern8_time_cap); - if (ret) - goto out; - - ret = ufshcd_dme_peer_get(hba, - UIC_ARG_MIB_SEL(RX_HIBERN8TIME_CAPABILITY, - UIC_ARG_MPHY_RX_GEN_SEL_INDEX(0)), - &peer_rx_hibern8_time_cap); - if (ret) - goto out; - - max_hibern8_time = max(local_tx_hibern8_time_cap, - peer_rx_hibern8_time_cap); - /* make sure proper unit conversion is applied */ - tuned_pa_hibern8time = ((max_hibern8_time * HIBERN8TIME_UNIT_US) - / PA_HIBERN8_TIME_UNIT_US); - ret = ufshcd_dme_set(hba, UIC_ARG_MIB(PA_HIBERN8TIME), - tuned_pa_hibern8time); -out: - return ret; -} - -/** * ufshcd_quirk_tune_host_pa_tactivate - Ensures that host PA_TACTIVATE is * less than device PA_TACTIVATE time. * @hba: per-adapter instance @@ -8505,11 +8369,6 @@ out: static void ufshcd_tune_unipro_params(struct ufs_hba *hba) { - if (ufshcd_is_unipro_pa_params_tuning_req(hba)) { - ufshcd_tune_pa_tactivate(hba); - ufshcd_tune_pa_hibern8time(hba); - } - ufshcd_vops_apply_dev_quirks(hba); if (hba->dev_quirks & UFS_DEVICE_QUIRK_PA_TACTIVATE) diff --git a/drivers/ufs/host/ufs-exynos.c b/drivers/ufs/host/ufs-exynos.c index 7ffc28e22784..e8d3302f6df0 100644 --- a/drivers/ufs/host/ufs-exynos.c +++ b/drivers/ufs/host/ufs-exynos.c @@ -1744,6 +1744,7 @@ static const struct of_device_id exynos_ufs_of_match[] = { .data = &fsd_ufs_drvs }, {}, }; +MODULE_DEVICE_TABLE(of, exynos_ufs_of_match); static const struct dev_pm_ops exynos_ufs_pm_ops = { SET_SYSTEM_SLEEP_PM_OPS(ufshcd_system_suspend, ufshcd_system_resume) diff --git a/drivers/ufs/host/ufs-mediatek.c b/drivers/ufs/host/ufs-mediatek.c index 0b0c923b1d7b..c4f997196c57 100644 --- a/drivers/ufs/host/ufs-mediatek.c +++ b/drivers/ufs/host/ufs-mediatek.c @@ -52,6 +52,7 @@ static const struct of_device_id ufs_mtk_of_match[] = { { .compatible = "mediatek,mt8183-ufshci" }, {}, }; +MODULE_DEVICE_TABLE(of, ufs_mtk_of_match); /* * Details of UIC Errors diff --git a/drivers/ufs/host/ufs-qcom.c b/drivers/ufs/host/ufs-qcom.c index 3a91255036dd..0b02e697ea5b 100644 --- a/drivers/ufs/host/ufs-qcom.c +++ b/drivers/ufs/host/ufs-qcom.c @@ -528,8 +528,7 @@ static int ufs_qcom_link_startup_notify(struct ufs_hba *hba, * and device TX LCC are disabled once link startup is * completed. */ - if (ufshcd_get_local_unipro_ver(hba) != UFS_UNIPRO_VER_1_41) - err = ufshcd_disable_host_tx_lcc(hba); + err = ufshcd_disable_host_tx_lcc(hba); break; default: diff --git a/include/scsi/iser.h b/include/scsi/iser.h index 2e678fa74eca..07a83bfa2b8e 100644 --- a/include/scsi/iser.h +++ b/include/scsi/iser.h @@ -63,7 +63,7 @@ struct iser_cm_hdr { * @rsvd: reserved * @write_stag: write rkey * @write_va: write virtual address - * @reaf_stag: read rkey + * @read_stag: read rkey * @read_va: read virtual address */ struct iser_ctrl { diff --git a/include/scsi/libfcoe.h b/include/scsi/libfcoe.h index 8300ef1a982e..3c5899290aed 100644 --- a/include/scsi/libfcoe.h +++ b/include/scsi/libfcoe.h @@ -157,7 +157,9 @@ struct fcoe_ctlr { /** * fcoe_ctlr_priv() - Return the private data from a fcoe_ctlr - * @cltr: The fcoe_ctlr whose private data will be returned + * @ctlr: The fcoe_ctlr whose private data will be returned + * + * Returns: pointer to the private data */ static inline void *fcoe_ctlr_priv(const struct fcoe_ctlr *ctlr) { @@ -174,7 +176,6 @@ static inline void *fcoe_ctlr_priv(const struct fcoe_ctlr *ctlr) * struct fcoe_fcf - Fibre-Channel Forwarder * @list: list linkage * @event_work: Work for FC Transport actions queue - * @event: The event to be processed * @fip: The controller that the FCF was discovered on * @fcf_dev: The associated fcoe_fcf_device instance * @time: system time (jiffies) when an advertisement was last received @@ -188,6 +189,7 @@ static inline void *fcoe_ctlr_priv(const struct fcoe_ctlr *ctlr) * @flogi_sent: current FLOGI sent to this FCF * @flags: flags received from advertisement * @fka_period: keep-alive period, in jiffies + * @fd_flags: no need for FKA from ENode * * A Fibre-Channel Forwarder (FCF) is the entity on the Ethernet that * passes FCoE frames on to an FC fabric. This structure represents @@ -222,6 +224,7 @@ struct fcoe_fcf { /** * struct fcoe_rport - VN2VN remote port + * @rdata: libfc remote port private data * @time: time of create or last beacon packet received from node * @fcoe_len: max FCoE frame size, not including VLAN or Ethernet headers * @flags: flags from probe or claim @@ -266,8 +269,10 @@ void fcoe_get_lesb(struct fc_lport *, struct fc_els_lesb *); void fcoe_ctlr_get_lesb(struct fcoe_ctlr_device *ctlr_dev); /** - * is_fip_mode() - returns true if FIP mode selected. + * is_fip_mode() - test if FIP mode selected. * @fip: FCoE controller. + * + * Returns: %true if FIP mode is selected */ static inline bool is_fip_mode(struct fcoe_ctlr *fip) { @@ -318,9 +323,10 @@ struct fcoe_transport { * @kthread: The thread context (used by bnx2fc) * @work: The work item (used by fcoe) * @fcoe_rx_list: The queue of pending packets to process - * @page: The memory page for calculating frame trailer CRCs + * @crc_eof_page: The memory page for calculating frame trailer CRCs * @crc_eof_offset: The offset into the CRC page pointing to available * memory for a new trailer + * @lock: local lock for members of this struct */ struct fcoe_percpu_s { struct task_struct *kthread; @@ -343,7 +349,8 @@ struct fcoe_percpu_s { * @timer: The queue timer * @destroy_work: Handle for work context * (to prevent RTNL deadlocks) - * @data_srt_addr: Source address for data + * @data_src_addr: Source address for data + * @get_netdev: function that returns a &net_device from @lport * * An instance of this structure is to be allocated along with the * Scsi_Host and libfc fc_lport structures. @@ -364,6 +371,8 @@ struct fcoe_port { /** * fcoe_get_netdev() - Return the net device associated with a local port * @lport: The local port to get the net device from + * + * Returns: the &net_device associated with this @lport */ static inline struct net_device *fcoe_get_netdev(const struct fc_lport *lport) { @@ -383,8 +392,10 @@ void fcoe_fcf_get_selected(struct fcoe_fcf_device *); void fcoe_ctlr_set_fip_mode(struct fcoe_ctlr_device *); /** - * struct netdev_list - * A mapping from netdevice to fcoe_transport + * struct fcoe_netdev_mapping - A mapping from &net_device to &fcoe_transport + * @list: list linkage of the mappings + * @netdev: the &net_device + * @ft: the fcoe_transport associated with @netdev */ struct fcoe_netdev_mapping { struct list_head list; diff --git a/include/scsi/scsi.h b/include/scsi/scsi.h index 4498f845b112..d90645f06a3a 100644 --- a/include/scsi/scsi.h +++ b/include/scsi/scsi.h @@ -69,7 +69,7 @@ static inline int scsi_is_wlun(u64 lun) * @status: the status passed up from the driver (including host and * driver components) * - * This returns true if the status code is SAM_STAT_CHECK_CONDITION. + * Returns: %true if the status code is SAM_STAT_CHECK_CONDITION. */ static inline int scsi_status_is_check_condition(int status) { @@ -189,12 +189,13 @@ enum scsi_disposition { /* Used to obtain the PCI location of a device */ #define SCSI_IOCTL_GET_PCI 0x5387 -/** scsi_status_is_good - check the status return. +/** + * scsi_status_is_good - check the status return. * * @status: the status passed up from the driver (including host and * driver components) * - * This returns true for known good conditions that may be treated as + * Returns: %true for known good conditions that may be treated as * command completed normally */ static inline bool scsi_status_is_good(int status) diff --git a/include/scsi/scsi_cmnd.h b/include/scsi/scsi_cmnd.h index 526def14e7fb..45c40d200154 100644 --- a/include/scsi/scsi_cmnd.h +++ b/include/scsi/scsi_cmnd.h @@ -353,6 +353,8 @@ static inline u8 get_host_byte(struct scsi_cmnd *cmd) /** * scsi_msg_to_host_byte() - translate message byte + * @cmd: the SCSI command + * @msg: the SCSI parallel message byte to translate * * Translate the SCSI parallel message byte to a matching * host byte setting. A message of COMMAND_COMPLETE indicates diff --git a/include/scsi/scsi_transport_fc.h b/include/scsi/scsi_transport_fc.h index fd039306ffbb..4b884b8013e0 100644 --- a/include/scsi/scsi_transport_fc.h +++ b/include/scsi/scsi_transport_fc.h @@ -771,10 +771,9 @@ struct fc_function_template { /** * fc_remote_port_chkready - called to validate the remote port state * prior to initiating io to the port. - * - * Returns a scsi result code that can be returned by the LLDD. - * * @rport: remote port to be checked + * + * Returns: a scsi result code that can be returned by the LLDD. **/ static inline int fc_remote_port_chkready(struct fc_rport *rport) diff --git a/include/scsi/scsi_transport_srp.h b/include/scsi/scsi_transport_srp.h index dfc78aa112ad..5b70b538447e 100644 --- a/include/scsi/scsi_transport_srp.h +++ b/include/scsi/scsi_transport_srp.h @@ -74,7 +74,7 @@ struct srp_rport { }; /** - * struct srp_function_template + * struct srp_function_template - template for SRP initiator drivers * * Fields that are only relevant for SRP initiator drivers: * @has_rport_state: Whether or not to create the state, fast_io_fail_tmo and @@ -124,7 +124,7 @@ enum scsi_timeout_action srp_timed_out(struct scsi_cmnd *scmd); * srp_chkready() - evaluate the transport layer state before I/O * @rport: SRP target port pointer. * - * Returns a SCSI result code that can be returned by the LLD queuecommand() + * Returns: a SCSI result code that can be returned by the LLD queuecommand() * implementation. The role of this function is similar to that of * fc_remote_port_chkready(). */ diff --git a/include/ufs/ufshcd.h b/include/ufs/ufshcd.h index 93afb726213f..bad88bd91995 100644 --- a/include/ufs/ufshcd.h +++ b/include/ufs/ufshcd.h @@ -1389,8 +1389,6 @@ void ufshcd_release(struct ufs_hba *hba); void ufshcd_clkgate_delay_set(struct device *dev, unsigned long value); -u32 ufshcd_get_local_unipro_ver(struct ufs_hba *hba); - int ufshcd_get_vreg(struct device *dev, struct ufs_vreg *vreg); int ufshcd_send_uic_cmd(struct ufs_hba *hba, struct uic_command *uic_cmd); diff --git a/include/ufs/ufshci.h b/include/ufs/ufshci.h index 88193f5540e5..385e1c6b8d60 100644 --- a/include/ufs/ufshci.h +++ b/include/ufs/ufshci.h @@ -355,12 +355,8 @@ enum { /* Interrupt disable masks */ enum { - /* Interrupt disable mask for UFSHCI v1.0 */ - INTERRUPT_MASK_ALL_VER_10 = 0x30FFF, - INTERRUPT_MASK_RW_VER_10 = 0x30000, - /* Interrupt disable mask for UFSHCI v1.1 */ - INTERRUPT_MASK_ALL_VER_11 = 0x31FFF, + INTERRUPT_MASK_ALL_VER_11 = 0x31FFF, /* Interrupt disable mask for UFSHCI v2.1 */ INTERRUPT_MASK_ALL_VER_21 = 0x71FFF, @@ -425,13 +421,6 @@ union ufs_crypto_cfg_entry { * Request Descriptor Definitions */ -/* Transfer request command type */ -enum utp_cmd_type { - UTP_CMD_TYPE_SCSI = 0x0, - UTP_CMD_TYPE_UFS = 0x1, - UTP_CMD_TYPE_DEV_MANAGE = 0x2, -}; - /* To accommodate UFS2.0 required Command type */ enum { UTP_CMD_TYPE_UFS_STORAGE = 0x1, |