diff options
| -rw-r--r-- | drivers/usb/phy/phy-mxs-usb.c | 33 |
1 files changed, 26 insertions, 7 deletions
diff --git a/drivers/usb/phy/phy-mxs-usb.c b/drivers/usb/phy/phy-mxs-usb.c index d9d29f0b37de..e172af75f602 100644 --- a/drivers/usb/phy/phy-mxs-usb.c +++ b/drivers/usb/phy/phy-mxs-usb.c @@ -150,6 +150,15 @@ #define MXS_PHY_TX_D_CAL_MIN 79 #define MXS_PHY_TX_D_CAL_MAX 119 +/* + * At imx6q/6sl/6sx, the PHY2's clock is controlled by hardware directly, + * eg, according to PHY's suspend status. In these PHYs, we only need to + * open the clock at the initialization and close it at its shutdown routine. + * These PHYs can send resume signal without software interfere if not + * gate clock. + */ +#define MXS_PHY_HARDWARE_CONTROL_PHY2_CLK BIT(4) + struct mxs_phy_data { unsigned int flags; }; @@ -161,12 +170,14 @@ static const struct mxs_phy_data imx23_phy_data = { static const struct mxs_phy_data imx6q_phy_data = { .flags = MXS_PHY_SENDING_SOF_TOO_FAST | MXS_PHY_DISCONNECT_LINE_WITHOUT_VBUS | - MXS_PHY_NEED_IP_FIX, + MXS_PHY_NEED_IP_FIX | + MXS_PHY_HARDWARE_CONTROL_PHY2_CLK, }; static const struct mxs_phy_data imx6sl_phy_data = { .flags = MXS_PHY_DISCONNECT_LINE_WITHOUT_VBUS | - MXS_PHY_NEED_IP_FIX, + MXS_PHY_NEED_IP_FIX | + MXS_PHY_HARDWARE_CONTROL_PHY2_CLK, }; static const struct mxs_phy_data vf610_phy_data = { @@ -175,7 +186,8 @@ static const struct mxs_phy_data vf610_phy_data = { }; static const struct mxs_phy_data imx6sx_phy_data = { - .flags = MXS_PHY_DISCONNECT_LINE_WITHOUT_VBUS, + .flags = MXS_PHY_DISCONNECT_LINE_WITHOUT_VBUS | + MXS_PHY_HARDWARE_CONTROL_PHY2_CLK, }; static const struct mxs_phy_data imx6ul_phy_data = { @@ -518,12 +530,19 @@ static int mxs_phy_suspend(struct usb_phy *x, int suspend) } writel(BM_USBPHY_CTRL_CLKGATE, x->io_priv + HW_USBPHY_CTRL_SET); - clk_disable_unprepare(mxs_phy->clk); + if (!(mxs_phy->port_id == 1 && + (mxs_phy->data->flags & + MXS_PHY_HARDWARE_CONTROL_PHY2_CLK))) + clk_disable_unprepare(mxs_phy->clk); } else { mxs_phy_clock_switch_delay(); - ret = clk_prepare_enable(mxs_phy->clk); - if (ret) - return ret; + if (!(mxs_phy->port_id == 1 && + (mxs_phy->data->flags & + MXS_PHY_HARDWARE_CONTROL_PHY2_CLK))) { + ret = clk_prepare_enable(mxs_phy->clk); + if (ret) + return ret; + } writel(BM_USBPHY_CTRL_CLKGATE, x->io_priv + HW_USBPHY_CTRL_CLR); writel(0, x->io_priv + HW_USBPHY_PWD); |