diff options
107 files changed, 4229 insertions, 249 deletions
diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt index 6809e4e51ed2..60d4a1e0a9b5 100644 --- a/Documentation/devicetree/bindings/arm/rockchip.txt +++ b/Documentation/devicetree/bindings/arm/rockchip.txt @@ -22,3 +22,7 @@ Rockchip platforms device tree bindings - compatible = "firefly,firefly-rk3288", "rockchip,rk3288"; or - compatible = "firefly,firefly-rk3288-beta", "rockchip,rk3288"; + +- ChipSPARK PopMetal-RK3288 board: + Required root node properties: + - compatible = "chipspark,popmetal-rk3288", "rockchip,rk3288"; diff --git a/Documentation/devicetree/bindings/watchdog/atmel-wdt.txt b/Documentation/devicetree/bindings/watchdog/atmel-wdt.txt index f90e294d7631..a4d869744f59 100644 --- a/Documentation/devicetree/bindings/watchdog/atmel-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/atmel-wdt.txt @@ -26,6 +26,11 @@ Optional properties: - atmel,disable : Should be present if you want to disable the watchdog. - atmel,idle-halt : Should be present if you want to stop the watchdog when entering idle state. + CAUTION: This property should be used with care, it actually makes the + watchdog not counting when the CPU is in idle state, therefore the + watchdog reset time depends on mean CPU usage and will not reset at all + if the CPU stop working while it is in idle state, which is probably + not what you want. - atmel,dbg-halt : Should be present if you want to stop the watchdog when entering debug state. diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index a533f72ac05a..7f85ca083b4a 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -1,5 +1,7 @@ ifeq ($(CONFIG_OF),y) +dtb-$(CONFIG_ARCH_ALPINE) += \ + alpine-db.dtb dtb-$(CONFIG_MACH_ASM9260) += \ alphascale-asm9260-devkit.dtb # Keep at91 dtb files sorted alphabetically for each SoC @@ -42,6 +44,7 @@ dtb-$(CONFIG_SOC_SAM_V7) += \ sama5d34ek.dtb \ sama5d35ek.dtb \ sama5d36ek.dtb \ + at91-sama5d4_xplained.dtb \ at91-sama5d4ek.dtb dtb-$(CONFIG_ARCH_ATLAS6) += \ atlas6-evb.dtb @@ -59,13 +62,15 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \ bcm4708-netgear-r6300-v2.dtb \ bcm47081-asus-rt-n18u.dtb \ bcm47081-buffalo-wzr-600dhp2.dtb \ - bcm47081-buffalo-wzr-900dhp.dtb + bcm47081-buffalo-wzr-900dhp.dtb \ + bcm4709-netgear-r8000.dtb dtb-$(CONFIG_ARCH_BCM_63XX) += \ bcm963138dvt.dtb dtb-$(CONFIG_ARCH_BCM_CYGNUS) += \ bcm911360_entphn.dtb \ bcm911360k.dtb \ - bcm958300k.dtb + bcm958300k.dtb \ + bcm958305k.dtb dtb-$(CONFIG_ARCH_BCM_MOBILE) += \ bcm28155-ap.dtb \ bcm21664-garnet.dtb @@ -199,6 +204,8 @@ dtb-$(CONFIG_ARCH_LPC32XX) += \ ea3250.dtb phy3250.dtb dtb-$(CONFIG_MACH_MESON6) += \ meson6-atv1200.dtb +dtb-$(CONFIG_MACH_MESON8) += \ + meson8-minix-neo-x8.dtb dtb-$(CONFIG_ARCH_MMP) += \ pxa168-aspenite.dtb \ pxa910-dkb.dtb \ @@ -627,11 +634,14 @@ dtb-$(CONFIG_MACH_ARMADA_38X) += \ armada-388-db.dtb \ armada-388-gp.dtb \ armada-388-rd.dtb +dtb-$(CONFIG_MACH_ARMADA_39X) += \ + armada-398-db.dtb dtb-$(CONFIG_MACH_ARMADA_XP) += \ armada-xp-axpwifiap.dtb \ armada-xp-db.dtb \ armada-xp-gp.dtb \ armada-xp-lenovo-ix4-300d.dtb \ + armada-xp-linksys-mamba.dtb \ armada-xp-matrix.dtb \ armada-xp-netgear-rn2120.dtb \ armada-xp-openblocks-ax3-4.dtb \ diff --git a/arch/arm/boot/dts/alpine-db.dts b/arch/arm/boot/dts/alpine-db.dts new file mode 100644 index 000000000000..dfb5a0802273 --- /dev/null +++ b/arch/arm/boot/dts/alpine-db.dts @@ -0,0 +1,35 @@ +/* + * Copyright 2015 Annapurna Labs Ltd. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms and conditions of the GNU General Public License, + * version 2, as published by the Free Software Foundation. + * + * Alternatively, redistribution and use in source and binary forms, with or + * without modification, are permitted provided that the following conditions + * are met: + * + * * Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * + * * Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * + * This program is distributed in the hope it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + */ + +/dts-v1/; + +#include "alpine.dtsi" + +/ { + model = "Annapurna Labs Alpine Dev Board"; + /* no need for anything outside SOC */ +}; + diff --git a/arch/arm/boot/dts/alpine.dtsi b/arch/arm/boot/dts/alpine.dtsi new file mode 100644 index 000000000000..519f58cc9761 --- /dev/null +++ b/arch/arm/boot/dts/alpine.dtsi @@ -0,0 +1,141 @@ +/* + * Copyright 2015 Annapurna Labs Ltd. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms and conditions of the GNU General Public License, + * version 2, as published by the Free Software Foundation. + * + * Alternatively, redistribution and use in source and binary forms, with or + * without modification, are permitted provided that the following conditions + * are met: + * + * * Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * + * * Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * + * This program is distributed in the hope it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + */ + +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include "skeleton64.dtsi" + +/ { + /* SOC compatibility */ + compatible = "al,alpine"; + + /* CPU Configuration */ + cpus { + #address-cells = <1>; + #size-cells = <0>; + enable-method = "al,alpine-smp"; + + cpu@0 { + compatible = "arm,cortex-a15"; + device_type = "cpu"; + reg = <0>; + clock-frequency = <0>; /* Filled by loader */ + }; + + cpu@1 { + compatible = "arm,cortex-a15"; + device_type = "cpu"; + reg = <1>; + clock-frequency = <0>; /* Filled by loader */ + }; + + cpu@2 { + compatible = "arm,cortex-a15"; + device_type = "cpu"; + reg = <2>; + clock-frequency = <0>; /* Filled by loader */ + }; + + cpu@3 { + compatible = "arm,cortex-a15"; + device_type = "cpu"; + reg = <3>; + clock-frequency = <0>; /* Filled by loader */ + }; + }; + + soc { + #address-cells = <2>; + #size-cells = <2>; + compatible = "simple-bus"; + interrupt-parent = <&gic>; + ranges; + + arch-timer { + compatible = "arm,cortex-a15-timer", + "arm,armv7-timer"; + interrupts = + <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; + clock-frequency = <0>; /* Filled by loader */ + }; + + /* Interrupt Controller */ + gic: gic@fb001000 { + compatible = "arm,cortex-a15-gic"; + #interrupt-cells = <3>; + #size-cells = <0>; + #address-cells = <0>; + interrupt-controller; + reg = <0x0 0xfb001000 0x0 0x1000>, + <0x0 0xfb002000 0x0 0x2000>, + <0x0 0xfb004000 0x0 0x1000>, + <0x0 0xfb006000 0x0 0x2000>; + interrupts = + <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; + }; + + /* CPU Resume registers */ + cpu-resume@fbff5ec0 { + compatible = "al,alpine-cpu-resume"; + reg = <0x0 0xfbff5ec0 0x0 0x30>; + }; + + /* North Bridge Service Registers */ + sysfabric-service@fb070000 { + compatible = "al,alpine-sysfabric-service", "syscon"; + reg = <0x0 0xfb070000 0x0 0x10000>; + }; + + /* Performance Monitor Unit */ + pmu { + compatible = "arm,cortex-a15-pmu"; + interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>; + }; + + uart0:uart@fd883000 { + compatible = "ns16550a"; + reg = <0x0 0xfd883000 0x0 0x1000>; + clock-frequency = <0>; /* Filled by loader */ + interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + }; + + uart1:uart@0xfd884000 { + compatible = "ns16550a"; + reg = <0x0 0xfd884000 0x0 0x1000>; + clock-frequency = <0>; /* Filled by loader */ + interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + }; + }; +}; diff --git a/arch/arm/boot/dts/armada-370-db.dts b/arch/arm/boot/dts/armada-370-db.dts index e993c46bd472..485ecf856fae 100644 --- a/arch/arm/boot/dts/armada-370-db.dts +++ b/arch/arm/boot/dts/armada-370-db.dts @@ -55,7 +55,7 @@ compatible = "marvell,a370-db", "marvell,armada370", "marvell,armada-370-xp"; chosen { - bootargs = "console=ttyS0,115200 earlyprintk"; + stdout-path = "serial0:115200n8"; }; memory { diff --git a/arch/arm/boot/dts/armada-370-mirabox.dts b/arch/arm/boot/dts/armada-370-mirabox.dts index b10ceb488efe..0f40d5da28c3 100644 --- a/arch/arm/boot/dts/armada-370-mirabox.dts +++ b/arch/arm/boot/dts/armada-370-mirabox.dts @@ -51,7 +51,7 @@ compatible = "globalscale,mirabox", "marvell,armada370", "marvell,armada-370-xp"; chosen { - bootargs = "console=ttyS0,115200 earlyprintk"; + stdout-path = "serial0:115200n8"; }; memory { diff --git a/arch/arm/boot/dts/armada-370-netgear-rn102.dts b/arch/arm/boot/dts/armada-370-netgear-rn102.dts index 3f8cc3845a5e..a31207860f34 100644 --- a/arch/arm/boot/dts/armada-370-netgear-rn102.dts +++ b/arch/arm/boot/dts/armada-370-netgear-rn102.dts @@ -53,7 +53,7 @@ compatible = "netgear,readynas-102", "marvell,armada370", "marvell,armada-370-xp"; chosen { - bootargs = "console=ttyS0,115200 earlyprintk"; + stdout-path = "serial0:115200n8"; }; memory { diff --git a/arch/arm/boot/dts/armada-370-netgear-rn104.dts b/arch/arm/boot/dts/armada-370-netgear-rn104.dts index 99eb8a014ac6..00540f292979 100644 --- a/arch/arm/boot/dts/armada-370-netgear-rn104.dts +++ b/arch/arm/boot/dts/armada-370-netgear-rn104.dts @@ -53,7 +53,7 @@ compatible = "netgear,readynas-104", "marvell,armada370", "marvell,armada-370-xp"; chosen { - bootargs = "console=ttyS0,115200 earlyprintk"; + stdout-path = "serial0:115200n8"; }; memory { diff --git a/arch/arm/boot/dts/armada-370-rd.dts b/arch/arm/boot/dts/armada-370-rd.dts index 6ae36a38beb2..19475e68b8e9 100644 --- a/arch/arm/boot/dts/armada-370-rd.dts +++ b/arch/arm/boot/dts/armada-370-rd.dts @@ -64,7 +64,7 @@ compatible = "marvell,a370-rd", "marvell,armada370", "marvell,armada-370-xp"; chosen { - bootargs = "console=ttyS0,115200 earlyprintk"; + stdout-path = "serial0:115200n8"; }; memory { diff --git a/arch/arm/boot/dts/armada-370-synology-ds213j.dts b/arch/arm/boot/dts/armada-370-synology-ds213j.dts index 59f74e66963f..b42b767763aa 100644 --- a/arch/arm/boot/dts/armada-370-synology-ds213j.dts +++ b/arch/arm/boot/dts/armada-370-synology-ds213j.dts @@ -67,8 +67,7 @@ "marvell,armada-370-xp"; chosen { - bootargs = "console=ttyS0,115200 earlyprintk"; - stdout-path = &uart0; + stdout-path = "serial0:115200n8"; }; memory { diff --git a/arch/arm/boot/dts/armada-370-xp.dtsi b/arch/arm/boot/dts/armada-370-xp.dtsi index 8a322ad57e5f..7b3393e264f8 100644 --- a/arch/arm/boot/dts/armada-370-xp.dtsi +++ b/arch/arm/boot/dts/armada-370-xp.dtsi @@ -59,8 +59,8 @@ compatible = "marvell,armada-370-xp"; aliases { - eth0 = ð0; - eth1 = ð1; + serial0 = &uart0; + serial1 = &uart1; }; cpus { @@ -223,7 +223,7 @@ <0x20250 0x8>; }; - mpic: interrupt-controller@20000 { + mpic: interrupt-controller@20a00 { compatible = "marvell,mpic"; #interrupt-cells = <1>; #size-cells = <1>; diff --git a/arch/arm/boot/dts/armada-370.dtsi b/arch/arm/boot/dts/armada-370.dtsi index 27397f151def..50f259b20f94 100644 --- a/arch/arm/boot/dts/armada-370.dtsi +++ b/arch/arm/boot/dts/armada-370.dtsi @@ -232,7 +232,7 @@ reg = <0x18330 0x4>; }; - interrupt-controller@20000 { + interrupt-controller@20a00 { reg = <0x20a00 0x1d0>, <0x21870 0x58>; }; diff --git a/arch/arm/boot/dts/armada-375-db.dts b/arch/arm/boot/dts/armada-375-db.dts index 0440891425c0..4eabc9c21f8d 100644 --- a/arch/arm/boot/dts/armada-375-db.dts +++ b/arch/arm/boot/dts/armada-375-db.dts @@ -55,7 +55,7 @@ compatible = "marvell,a375-db", "marvell,armada375"; chosen { - bootargs = "console=ttyS0,115200 earlyprintk"; + stdout-path = "serial0:115200n8"; }; memory { diff --git a/arch/arm/boot/dts/armada-375.dtsi b/arch/arm/boot/dts/armada-375.dtsi index ba3c57e0af72..c6fedf2bfe3d 100644 --- a/arch/arm/boot/dts/armada-375.dtsi +++ b/arch/arm/boot/dts/armada-375.dtsi @@ -60,8 +60,8 @@ gpio0 = &gpio0; gpio1 = &gpio1; gpio2 = &gpio2; - ethernet0 = ð0; - ethernet1 = ð1; + serial0 = &uart0; + serial1 = &uart1; }; clocks { @@ -276,7 +276,7 @@ status = "disabled"; }; - serial@12000 { + uart0: serial@12000 { compatible = "snps,dw-apb-uart"; reg = <0x12000 0x100>; reg-shift = <2>; @@ -286,7 +286,7 @@ status = "disabled"; }; - serial@12100 { + uart1: serial@12100 { compatible = "snps,dw-apb-uart"; reg = <0x12100 0x100>; reg-shift = <2>; @@ -394,7 +394,7 @@ reg = <0x20000 0x100>, <0x20180 0x20>; }; - mpic: interrupt-controller@20000 { + mpic: interrupt-controller@20a00 { compatible = "marvell,mpic"; reg = <0x20a00 0x2d0>, <0x21070 0x58>; #interrupt-cells = <1>; diff --git a/arch/arm/boot/dts/armada-385-db-ap.dts b/arch/arm/boot/dts/armada-385-db-ap.dts index 57b9119fb3e0..d6b0f7db9624 100644 --- a/arch/arm/boot/dts/armada-385-db-ap.dts +++ b/arch/arm/boot/dts/armada-385-db-ap.dts @@ -49,8 +49,7 @@ compatible = "marvell,a385-db-ap", "marvell,armada385", "marvell,armada38x"; chosen { - bootargs = "console=ttyS0,115200"; - stdout-path = &uart1; + stdout-path = "serial1:115200n8"; }; memory { @@ -150,6 +149,19 @@ phy = <&phy0>; phy-mode = "rgmii-id"; }; + + nfc: flash@d0000 { + status = "okay"; + #address-cells = <1>; + #size-cells = <1>; + + num-cs = <1>; + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + marvell,nand-keep-config; + marvell,nand-enable-arbiter; + nand-on-flash-bbt; + }; }; pcie-controller { diff --git a/arch/arm/boot/dts/armada-388-db.dts b/arch/arm/boot/dts/armada-388-db.dts index 16512efcd32c..51d1623de53e 100644 --- a/arch/arm/boot/dts/armada-388-db.dts +++ b/arch/arm/boot/dts/armada-388-db.dts @@ -54,7 +54,7 @@ "marvell,armada385", "marvell,armada380"; chosen { - bootargs = "console=ttyS0,115200 earlyprintk"; + stdout-path = "serial0:115200n8"; }; memory { @@ -99,7 +99,7 @@ phy-mode = "rgmii-id"; }; - usb@50000 { + usb@58000 { status = "ok"; }; diff --git a/arch/arm/boot/dts/armada-388-gp.dts b/arch/arm/boot/dts/armada-388-gp.dts index 590b383db323..78514ab0b47a 100644 --- a/arch/arm/boot/dts/armada-388-gp.dts +++ b/arch/arm/boot/dts/armada-388-gp.dts @@ -48,8 +48,7 @@ compatible = "marvell,a385-gp", "marvell,armada388", "marvell,armada380"; chosen { - bootargs = "console=ttyS0,115200"; - stdout-path = &uart0; + stdout-path = "serial0:115200n8"; }; memory { @@ -135,7 +134,7 @@ }; /* CON4 */ - usb@50000 { + usb@58000 { vcc-supply = <®_usb2_0_vbus>; status = "okay"; }; diff --git a/arch/arm/boot/dts/armada-388-rd.dts b/arch/arm/boot/dts/armada-388-rd.dts index d99baac72081..1dc6e2341cc2 100644 --- a/arch/arm/boot/dts/armada-388-rd.dts +++ b/arch/arm/boot/dts/armada-388-rd.dts @@ -55,7 +55,7 @@ "marvell,armada385","marvell,armada380"; chosen { - bootargs = "console=ttyS0,115200 earlyprintk"; + stdout-path = "serial0:115200n8"; }; memory { @@ -85,6 +85,16 @@ clock-frequency = <100000>; }; + sdhci@d8000 { + pinctrl-names = "default"; + pinctrl-0 = <&sdhci_pins>; + broken-cd; + no-1-8-v; + wp-inverted; + bus-width = <8>; + status = "okay"; + }; + serial@12000 { status = "okay"; }; diff --git a/arch/arm/boot/dts/armada-38x.dtsi b/arch/arm/boot/dts/armada-38x.dtsi index 1dff30a81e24..1a2dc370792f 100644 --- a/arch/arm/boot/dts/armada-38x.dtsi +++ b/arch/arm/boot/dts/armada-38x.dtsi @@ -59,9 +59,8 @@ aliases { gpio0 = &gpio0; gpio1 = &gpio1; - ethernet0 = ð0; - ethernet1 = ð1; - ethernet2 = ð2; + serial0 = &uart0; + serial1 = &uart1; }; soc { @@ -216,7 +215,7 @@ status = "disabled"; }; - serial@12100 { + uart1: serial@12100 { compatible = "snps,dw-apb-uart"; reg = <0x12100 0x100>; reg-shift = <2>; @@ -368,7 +367,7 @@ reg = <0x20000 0x100>, <0x20180 0x20>; }; - mpic: interrupt-controller@20000 { + mpic: interrupt-controller@20a00 { compatible = "marvell,mpic"; reg = <0x20a00 0x2d0>, <0x21070 0x58>; #interrupt-cells = <1>; @@ -435,7 +434,7 @@ status = "disabled"; }; - usb@50000 { + usb@58000 { compatible = "marvell,orion-ehci"; reg = <0x58000 0x500>; interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>; @@ -548,8 +547,11 @@ sdhci@d8000 { compatible = "marvell,armada-380-sdhci"; - reg = <0xd8000 0x1000>, <0xdc000 0x100>; - interrupts = <0 25 0x4>; + reg-names = "sdhci", "mbus", "conf-sdio3"; + reg = <0xd8000 0x1000>, + <0xdc000 0x100>, + <0x18454 0x4>; + interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; clocks = <&gateclk 17>; mrvl,clk-delay-cycles = <0x1F>; status = "disabled"; diff --git a/arch/arm/boot/dts/armada-390.dtsi b/arch/arm/boot/dts/armada-390.dtsi new file mode 100644 index 000000000000..094e39c66039 --- /dev/null +++ b/arch/arm/boot/dts/armada-390.dtsi @@ -0,0 +1,57 @@ +/* + * Device Tree Include file for Marvell Armada 390 SoC. + * + * Copyright (C) 2015 Marvell + * + * Thomas Petazzoni <[email protected]> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#include "armada-39x.dtsi" + +/ { + soc { + internal-regs { + pinctrl@18000 { + compatible = "marvell,mv88f6920-pinctrl"; + reg = <0x18000 0x20>; + }; + }; +}; diff --git a/arch/arm/boot/dts/armada-398-db.dts b/arch/arm/boot/dts/armada-398-db.dts new file mode 100644 index 000000000000..bbf83756c43c --- /dev/null +++ b/arch/arm/boot/dts/armada-398-db.dts @@ -0,0 +1,153 @@ +/* + * Device Tree Include file for Marvell Armada 398 Development Board + * + * Copyright (C) 2015 Marvell + * + * Thomas Petazzoni <[email protected]> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "armada-398.dtsi" + +/ { + model = "Marvell Armada 398 Development Board"; + compatible = "marvell,a398-db", "marvell,armada398", "marvell,armada390"; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory { + device_type = "memory"; + reg = <0x00000000 0x80000000>; /* 2 GB */ + }; + + soc { + ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000 + MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000>; + + internal-regs { + spi@10680 { + status = "okay"; + pinctrl-0 = <&spi1_pins>; + pinctrl-names = "default"; + + spi-flash@0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "n25q128a13"; + reg = <0>; + spi-max-frequency = <108000000>; + + partition@0 { + label = "U-Boot"; + reg = <0 0x400000>; + }; + + partition@400000 { + label = "Filesystem"; + reg = <0x400000 0x1000000>; + }; + }; + }; + + i2c@11000 { + pinctrl-0 = <&i2c0_pins>; + pinctrl-names = "default"; + status = "okay"; + clock-frequency = <100000>; + }; + + serial@12000 { + pinctrl-0 = <&uart0_pins>; + pinctrl-names = "default"; + status = "okay"; + }; + + serial@12100 { + pinctrl-0 = <&uart1_pins>; + pinctrl-names = "default"; + status = "okay"; + }; + + flash@d0000 { + status = "okay"; + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; + num-cs = <1>; + marvell,nand-keep-config; + marvell,nand-enable-arbiter; + nand-on-flash-bbt; + nand-ecc-strength = <8>; + nand-ecc-step-size = <512>; + + partition@0 { + label = "U-Boot"; + reg = <0 0x800000>; + }; + partition@800000 { + label = "Linux"; + reg = <0x800000 0x800000>; + }; + partition@1000000 { + label = "Filesystem"; + reg = <0x1000000 0x3f000000>; + }; + }; + }; + + pcie-controller { + status = "okay"; + + pcie@1,0 { + status = "okay"; + }; + + pcie@2,0 { + status = "okay"; + }; + + pcie@3,0 { + status = "okay"; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/armada-398.dtsi b/arch/arm/boot/dts/armada-398.dtsi new file mode 100644 index 000000000000..fdc25914e3a3 --- /dev/null +++ b/arch/arm/boot/dts/armada-398.dtsi @@ -0,0 +1,60 @@ +/* + * Device Tree Include file for Marvell Armada 398 SoC. + * + * Copyright (C) 2015 Marvell + * + * Thomas Petazzoni <[email protected]> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#include "armada-39x.dtsi" + +/ { + compatible = "marvell,armada398", "marvell,armada390"; + + soc { + internal-regs { + pinctrl@18000 { + compatible = "marvell,mv88f6928-pinctrl"; + reg = <0x18000 0x20>; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/armada-39x.dtsi b/arch/arm/boot/dts/armada-39x.dtsi new file mode 100644 index 000000000000..0e85fc15ceda --- /dev/null +++ b/arch/arm/boot/dts/armada-39x.dtsi @@ -0,0 +1,508 @@ +/* + * Device Tree Include file for Marvell Armada 39x family of SoCs. + * + * Copyright (C) 2015 Marvell + * + * Thomas Petazzoni <[email protected]> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#include "skeleton.dtsi" +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/interrupt-controller/irq.h> + +#define MBUS_ID(target,attributes) (((target) << 24) | ((attributes) << 16)) + +/ { + model = "Marvell Armada 39x family SoC"; + compatible = "marvell,armada390"; + + aliases { + serial0 = &uart0; + serial1 = &uart1; + serial2 = &uart2; + serial3 = &uart3; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + enable-method = "marvell,armada-390-smp"; + + cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a9"; + reg = <0>; + }; + cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a9"; + reg = <1>; + }; + }; + + soc { + compatible = "marvell,armada390-mbus", "marvell,armadaxp-mbus", + "simple-bus"; + #address-cells = <2>; + #size-cells = <1>; + controller = <&mbusc>; + interrupt-parent = <&gic>; + pcie-mem-aperture = <0xe0000000 0x8000000>; + pcie-io-aperture = <0xe8000000 0x100000>; + + bootrom { + compatible = "marvell,bootrom"; + reg = <MBUS_ID(0x01, 0x1d) 0 0x200000>; + }; + + internal-regs { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 MBUS_ID(0xf0, 0x01) 0 0x100000>; + + L2: cache-controller@8000 { + compatible = "arm,pl310-cache"; + reg = <0x8000 0x1000>; + cache-unified; + cache-level = <2>; + }; + + scu@c000 { + compatible = "arm,cortex-a9-scu"; + reg = <0xc000 0x100>; + }; + + timer@c600 { + compatible = "arm,cortex-a9-twd-timer"; + reg = <0xc600 0x20>; + interrupts = <GIC_PPI 13 (IRQ_TYPE_EDGE_RISING | GIC_CPU_MASK_SIMPLE(2))>; + clocks = <&coreclk 2>; + }; + + gic: interrupt-controller@d000 { + compatible = "arm,cortex-a9-gic"; + #interrupt-cells = <3>; + #size-cells = <0>; + interrupt-controller; + reg = <0xd000 0x1000>, + <0xc100 0x100>; + }; + + spi0: spi@10600 { + compatible = "marvell,orion-spi"; + reg = <0x10600 0x50>; + #address-cells = <1>; + #size-cells = <0>; + cell-index = <0>; + interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + spi1: spi@10680 { + compatible = "marvell,orion-spi"; + reg = <0x10680 0x50>; + #address-cells = <1>; + #size-cells = <0>; + cell-index = <1>; + interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + i2c0: i2c@11000 { + compatible = "marvell,mv64xxx-i2c"; + reg = <0x11000 0x20>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>; + timeout-ms = <1000>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + i2c1: i2c@11100 { + compatible = "marvell,mv64xxx-i2c"; + reg = <0x11100 0x20>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>; + timeout-ms = <1000>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + i2c2: i2c@11200 { + compatible = "marvell,mv64xxx-i2c"; + reg = <0x11200 0x20>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>; + timeout-ms = <1000>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + i2c3: i2c@11300 { + compatible = "marvell,mv64xxx-i2c"; + reg = <0x11300 0x20>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; + timeout-ms = <1000>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + uart0: serial@12000 { + compatible = "snps,dw-apb-uart"; + reg = <0x12000 0x100>; + reg-shift = <2>; + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; + reg-io-width = <1>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + uart1: serial@12100 { + compatible = "snps,dw-apb-uart"; + reg = <0x12100 0x100>; + reg-shift = <2>; + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; + reg-io-width = <1>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + uart2: serial@12200 { + compatible = "snps,dw-apb-uart"; + reg = <0x12200 0x100>; + reg-shift = <2>; + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; + reg-io-width = <1>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + uart3: serial@12300 { + compatible = "snps,dw-apb-uart"; + reg = <0x12300 0x100>; + reg-shift = <2>; + interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; + reg-io-width = <1>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + pinctrl@18000 { + i2c0_pins: i2c0-pins { + marvell,pins = "mpp2", "mpp3"; + marvell,function = "i2c0"; + }; + + uart0_pins: uart0-pins { + marvell,pins = "mpp0", "mpp1"; + marvell,function = "ua0"; + }; + + uart1_pins: uart1-pins { + marvell,pins = "mpp19", "mpp20"; + marvell,function = "ua1"; + }; + + spi1_pins: spi1-pins { + marvell,pins = "mpp56", "mpp57", "mpp58", "mpp59"; + marvell,function = "spi1"; + }; + + nand_pins: nand-pins { + marvell,pins = "mpp22", "mpp34", "mpp23", "mpp33", + "mpp38", "mpp28", "mpp40", "mpp42", + "mpp35", "mpp36", "mpp25", "mpp30", + "mpp32"; + marvell,function = "dev"; + }; + }; + + system-controller@18200 { + compatible = "marvell,armada-390-system-controller", + "marvell,armada-370-xp-system-controller"; + reg = <0x18200 0x100>; + }; + + gateclk: clock-gating-control@18220 { + compatible = "marvell,armada-390-gating-clock"; + reg = <0x18220 0x4>; + clocks = <&coreclk 0>; + #clock-cells = <1>; + }; + + coreclk: mvebu-sar@18600 { + compatible = "marvell,armada-390-core-clock"; + reg = <0x18600 0x04>; + #clock-cells = <1>; + }; + + mbusc: mbus-controller@20000 { + compatible = "marvell,mbus-controller"; + reg = <0x20000 0x100>, <0x20180 0x20>, <0x20250 0x8>; + }; + + mpic: interrupt-controller@20a00 { + compatible = "marvell,mpic"; + reg = <0x20a00 0x2d0>, <0x21070 0x58>; + #interrupt-cells = <1>; + #size-cells = <1>; + interrupt-controller; + msi-controller; + interrupts = <GIC_PPI 15 IRQ_TYPE_LEVEL_HIGH>; + }; + + timer@20300 { + compatible = "marvell,armada-380-timer", + "marvell,armada-xp-timer"; + reg = <0x20300 0x30>, <0x21040 0x30>; + interrupts-extended = <&gic GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, + <&gic GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>, + <&gic GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>, + <&gic GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>, + <&mpic 5>, + <&mpic 6>; + clocks = <&coreclk 2>, <&coreclk 5>; + clock-names = "nbclk", "fixed"; + }; + + cpurst@20800 { + compatible = "marvell,armada-370-cpu-reset"; + reg = <0x20800 0x10>; + }; + + pmsu@22000 { + compatible = "marvell,armada-390-pmsu", + "marvell,armada-380-pmsu"; + reg = <0x22000 0x1000>; + }; + + xor@60800 { + compatible = "marvell,orion-xor"; + reg = <0x60800 0x100 + 0x60a00 0x100>; + clocks = <&gateclk 22>; + status = "okay"; + + xor00 { + interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>; + dmacap,memcpy; + dmacap,xor; + }; + xor01 { + interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>; + dmacap,memcpy; + dmacap,xor; + dmacap,memset; + }; + }; + + xor@60900 { + compatible = "marvell,orion-xor"; + reg = <0x60900 0x100 + 0x60b00 0x100>; + clocks = <&gateclk 28>; + status = "okay"; + + xor10 { + interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>; + dmacap,memcpy; + dmacap,xor; + }; + xor11 { + interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>; + dmacap,memcpy; + dmacap,xor; + dmacap,memset; + }; + }; + + flash@d0000 { + compatible = "marvell,armada370-nand"; + reg = <0xd0000 0x54>; + #address-cells = <1>; + #size-cells = <1>; + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&coredivclk 0>; + status = "disabled"; + }; + + sdhci@d8000 { + compatible = "marvell,armada-380-sdhci"; + reg = <0xd8000 0x1000>, <0xdc000 0x100>; + interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gateclk 17>; + mrvl,clk-delay-cycles = <0x1F>; + status = "disabled"; + }; + + coredivclk: clock@e4250 { + compatible = "marvell,armada-390-corediv-clock", + "marvell,armada-380-corediv-clock"; + reg = <0xe4250 0xc>; + #clock-cells = <1>; + clocks = <&mainpll>; + clock-output-names = "nand"; + }; + }; + + pcie-controller { + compatible = "marvell,armada-370-pcie"; + status = "disabled"; + device_type = "pci"; + + #address-cells = <3>; + #size-cells = <2>; + + msi-parent = <&mpic>; + bus-range = <0x00 0xff>; + + ranges = + <0x82000000 0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x00002000 + 0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000 + 0x82000000 0 0x44000 MBUS_ID(0xf0, 0x01) 0x44000 0 0x00002000 + 0x82000000 0 0x48000 MBUS_ID(0xf0, 0x01) 0x48000 0 0x00002000 + 0x82000000 0x1 0 MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 0 MEM */ + 0x81000000 0x1 0 MBUS_ID(0x08, 0xe0) 0 1 0 /* Port 0 IO */ + 0x82000000 0x2 0 MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 1 MEM */ + 0x81000000 0x2 0 MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 1 IO */ + 0x82000000 0x3 0 MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 2 MEM */ + 0x81000000 0x3 0 MBUS_ID(0x04, 0xd0) 0 1 0 /* Port 2 IO */ + 0x82000000 0x4 0 MBUS_ID(0x04, 0xb8) 0 1 0 /* Port 3 MEM */ + 0x81000000 0x4 0 MBUS_ID(0x04, 0xb0) 0 1 0 /* Port 3 IO */>; + + /* + * This port can be either x4 or x1. When + * configured in x4 by the bootloader, then + * pcie@4,0 is not available. + */ + pcie@1,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x80000 0 0x2000>; + reg = <0x0800 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0 + 0x81000000 0 0 0x81000000 0x1 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>; + marvell,pcie-port = <0>; + marvell,pcie-lane = <0>; + clocks = <&gateclk 8>; + status = "disabled"; + }; + + /* x1 port */ + pcie@2,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x40000 0 0x2000>; + reg = <0x1000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0 + 0x81000000 0 0 0x81000000 0x2 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; + marvell,pcie-port = <1>; + marvell,pcie-lane = <0>; + clocks = <&gateclk 5>; + status = "disabled"; + }; + + /* x1 port */ + pcie@3,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x44000 0 0x2000>; + reg = <0x1800 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0 + 0x81000000 0 0 0x81000000 0x3 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>; + marvell,pcie-port = <2>; + marvell,pcie-lane = <0>; + clocks = <&gateclk 6>; + status = "disabled"; + }; + + /* + * x1 port only available when pcie@1,0 is + * configured as a x1 port + */ + pcie@4,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x48000 0 0x2000>; + reg = <0x2000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x4 0 1 0 + 0x81000000 0 0 0x81000000 0x4 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>; + marvell,pcie-port = <3>; + marvell,pcie-lane = <0>; + clocks = <&gateclk 7>; + status = "disabled"; + }; + }; + }; + + clocks { + /* 2 GHz fixed main PLL */ + mainpll: mainpll { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <2000000000>; + }; + }; +}; diff --git a/arch/arm/boot/dts/armada-xp-axpwifiap.dts b/arch/arm/boot/dts/armada-xp-axpwifiap.dts index c1fbab243609..dfd782b44e50 100644 --- a/arch/arm/boot/dts/armada-xp-axpwifiap.dts +++ b/arch/arm/boot/dts/armada-xp-axpwifiap.dts @@ -59,7 +59,7 @@ compatible = "marvell,rd-axpwifiap", "marvell,armadaxp-mv78230", "marvell,armadaxp", "marvell,armada-370-xp"; chosen { - bootargs = "console=ttyS0,115200 earlyprintk"; + stdout-path = "serial0:115200n8"; }; memory { diff --git a/arch/arm/boot/dts/armada-xp-db.dts b/arch/arm/boot/dts/armada-xp-db.dts index 48bdafe17526..103782407618 100644 --- a/arch/arm/boot/dts/armada-xp-db.dts +++ b/arch/arm/boot/dts/armada-xp-db.dts @@ -64,7 +64,7 @@ compatible = "marvell,axp-db", "marvell,armadaxp-mv78460", "marvell,armadaxp", "marvell,armada-370-xp"; chosen { - bootargs = "console=ttyS0,115200 earlyprintk"; + stdout-path = "serial0:115200n8"; }; memory { diff --git a/arch/arm/boot/dts/armada-xp-gp.dts b/arch/arm/boot/dts/armada-xp-gp.dts index 206aebba01be..565227eacf06 100644 --- a/arch/arm/boot/dts/armada-xp-gp.dts +++ b/arch/arm/boot/dts/armada-xp-gp.dts @@ -65,7 +65,7 @@ compatible = "marvell,axp-gp", "marvell,armadaxp-mv78460", "marvell,armadaxp", "marvell,armada-370-xp"; chosen { - bootargs = "console=ttyS0,115200 earlyprintk"; + stdout-path = "serial0:115200n8"; }; memory { diff --git a/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts b/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts index 5fb3c8b687cf..06a6a6c1fdf7 100644 --- a/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts +++ b/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts @@ -54,8 +54,7 @@ "marvell,armadaxp", "marvell,armada-370-xp"; chosen { - bootargs = "console=ttyS0,115200 earlyprintk"; - stdout-path = &uart0; + stdout-path = "serial0:115200n8"; }; memory { diff --git a/arch/arm/boot/dts/armada-xp-linksys-mamba.dts b/arch/arm/boot/dts/armada-xp-linksys-mamba.dts new file mode 100644 index 000000000000..a2cf2154dcdb --- /dev/null +++ b/arch/arm/boot/dts/armada-xp-linksys-mamba.dts @@ -0,0 +1,393 @@ +/* + * Device Tree file for the Linksys WRT1900AC (Mamba). + * + * Note: this board is shipped with a new generation boot loader that + * remaps internal registers at 0xf1000000. Therefore, if earlyprintk + * is used, the CONFIG_DEBUG_MVEBU_UART0_ALTERNATE option should be + * used. + * + * Copyright (C) 2014 Imre Kaloz <[email protected]> + * + * Based on armada-xp-axpwifiap.dts: + * + * Copyright (C) 2013 Marvell + * + * Thomas Petazzoni <[email protected]> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without + * any warranty of any kind, whether express or implied. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include "armada-xp-mv78230.dtsi" + +/ { + model = "Linksys WRT1900AC"; + compatible = "linksys,mamba", "marvell,armadaxp-mv78230", + "marvell,armadaxp", "marvell,armada-370-xp"; + + chosen { + bootargs = "console=ttyS0,115200"; + stdout-path = &uart0; + }; + + memory { + device_type = "memory"; + reg = <0x00000000 0x00000000 0x00000000 0x10000000>; /* 256MB */ + }; + + soc { + ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000 + MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000>; + + pcie-controller { + status = "okay"; + + /* Etron EJ168 USB 3.0 controller */ + pcie@1,0 { + /* Port 0, Lane 0 */ + status = "okay"; + }; + + /* First mini-PCIe port */ + pcie@2,0 { + /* Port 0, Lane 1 */ + status = "okay"; + }; + + /* Second mini-PCIe port */ + pcie@3,0 { + /* Port 0, Lane 3 */ + status = "okay"; + }; + }; + + internal-regs { + + /* J10: VCC, NC, RX, NC, TX, GND */ + serial@12000 { + status = "okay"; + }; + + sata@a0000 { + nr-ports = <1>; + status = "okay"; + }; + + ethernet@70000 { + pinctrl-0 = <&ge0_rgmii_pins>; + pinctrl-names = "default"; + status = "okay"; + phy-mode = "rgmii-id"; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + ethernet@74000 { + pinctrl-0 = <&ge1_rgmii_pins>; + pinctrl-names = "default"; + status = "okay"; + phy-mode = "rgmii-id"; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + /* USB part of the eSATA/USB 2.0 port */ + usb@50000 { + status = "okay"; + }; + + i2c@11000 { + status = "okay"; + clock-frequency = <100000>; + + tmp421@4c { + compatible = "ti,tmp421"; + reg = <0x4c>; + }; + + tlc59116@68 { + #address-cells = <1>; + #size-cells = <0>; + #gpio-cells = <2>; + compatible = "ti,tlc59116"; + reg = <0x68>; + + wan_amber@0 { + label = "mamba:amber:wan"; + reg = <0x0>; + }; + + wan_white@1 { + label = "mamba:white:wan"; + reg = <0x1>; + }; + + wlan_2g@2 { + label = "mamba:white:wlan_2g"; + reg = <0x2>; + }; + + wlan_5g@3 { + label = "mamba:white:wlan_5g"; + reg = <0x3>; + }; + + esata@4 { + label = "mamba:white:esata"; + reg = <0x4>; + }; + + usb2@5 { + label = "mamba:white:usb2"; + reg = <0x5>; + }; + + usb3_1@6 { + label = "mamba:white:usb3_1"; + reg = <0x6>; + }; + + usb3_2@7 { + label = "mamba:white:usb3_2"; + reg = <0x7>; + }; + + wps_white@8 { + label = "mamba:white:wps"; + reg = <0x8>; + }; + + wps_amber@9 { + label = "mamba:amber:wps"; + reg = <0x9>; + }; + }; + }; + + nand@d0000 { + status = "okay"; + num-cs = <1>; + marvell,nand-keep-config; + marvell,nand-enable-arbiter; + nand-on-flash-bbt; + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + + partition@0 { + label = "u-boot"; + reg = <0x0000000 0x100000>; /* 1MB */ + read-only; + }; + + partition@100000 { + label = "u_env"; + reg = <0x100000 0x40000>; /* 256KB */ + }; + + partition@140000 { + label = "s_env"; + reg = <0x140000 0x40000>; /* 256KB */ + }; + + partition@900000 { + label = "devinfo"; + reg = <0x900000 0x100000>; /* 1MB */ + read-only; + }; + + /* kernel1 overlaps with rootfs1 by design */ + partition@a00000 { + label = "kernel1"; + reg = <0xa00000 0x2800000>; /* 40MB */ + }; + + partition@d00000 { + label = "rootfs1"; + reg = <0xd00000 0x2500000>; /* 37MB */ + }; + + /* kernel2 overlaps with rootfs2 by design */ + partition@3200000 { + label = "kernel2"; + reg = <0x3200000 0x2800000>; /* 40MB */ + }; + + partition@3500000 { + label = "rootfs2"; + reg = <0x3500000 0x2500000>; /* 37MB */ + }; + + /* + * 38MB, last MB is for the BBT, not writable + */ + partition@5a00000 { + label = "syscfg"; + reg = <0x5a00000 0x2600000>; + }; + + /* + * Unused area between "s_env" and "devinfo". + * Moved here because otherwise the renumbered + * partitions would break the bootloader + * supplied bootargs + */ + partition@180000 { + label = "unused_area"; + reg = <0x180000 0x780000>; /* 7.5MB */ + }; + }; + + spi0: spi@10600 { + status = "okay"; + + spi-flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "everspin,mr25h256"; + reg = <0>; /* Chip select 0 */ + spi-max-frequency = <40000000>; + }; + }; + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-0 = <&keys_pin>; + pinctrl-names = "default"; + + button@1 { + label = "WPS"; + linux,code = <KEY_WPS_BUTTON>; + gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>; + }; + + button@2 { + label = "Factory Reset Button"; + linux,code = <KEY_RESTART>; + gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + pinctrl-0 = <&power_led_pin>; + pinctrl-names = "default"; + + power { + label = "mamba:white:power"; + gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + }; + + gpio_fan { + /* SUNON HA4010V4-0000-C99 */ + compatible = "gpio-fan"; + gpios = <&gpio0 24 0>; + + gpio-fan,speed-map = <0 0 + 4500 1>; + }; + + dsa@0 { + compatible = "marvell,dsa"; + #address-cells = <2>; + #size-cells = <0>; + + dsa,ethernet = <ð0>; + dsa,mii-bus = <&mdio>; + + switch@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0 0>; /* MDIO address 0, switch 0 in tree */ + + port@0 { + reg = <0>; + label = "lan4"; + }; + + port@1 { + reg = <1>; + label = "lan3"; + }; + + port@2 { + reg = <2>; + label = "lan2"; + }; + + port@3 { + reg = <3>; + label = "lan1"; + }; + + port@4 { + reg = <4>; + label = "internet"; + }; + + port@5 { + reg = <5>; + label = "cpu"; + }; + }; + }; +}; + +&pinctrl { + + keys_pin: keys-pin { + marvell,pins = "mpp32", "mpp33"; + marvell,function = "gpio"; + }; + + power_led_pin: power-led-pin { + marvell,pins = "mpp40"; + marvell,function = "gpio"; + }; + + gpio_fan_pin: gpio-fan-pin { + marvell,pins = "mpp24"; + marvell,function = "gpio"; + }; +}; diff --git a/arch/arm/boot/dts/armada-xp-matrix.dts b/arch/arm/boot/dts/armada-xp-matrix.dts index 56f958eb1ede..f894bc83e957 100644 --- a/arch/arm/boot/dts/armada-xp-matrix.dts +++ b/arch/arm/boot/dts/armada-xp-matrix.dts @@ -52,7 +52,7 @@ compatible = "marvell,axp-matrix", "marvell,armadaxp-mv78460", "marvell,armadaxp", "marvell,armada-370-xp"; chosen { - bootargs = "console=ttyS0,115200 earlyprintk"; + stdout-path = "serial0:115200n8"; }; memory { diff --git a/arch/arm/boot/dts/armada-xp-mv78260.dtsi b/arch/arm/boot/dts/armada-xp-mv78260.dtsi index 4a7cbed79b07..8479fdc9e9c2 100644 --- a/arch/arm/boot/dts/armada-xp-mv78260.dtsi +++ b/arch/arm/boot/dts/armada-xp-mv78260.dtsi @@ -57,7 +57,6 @@ gpio0 = &gpio0; gpio1 = &gpio1; gpio2 = &gpio2; - eth3 = ð3; }; cpus { diff --git a/arch/arm/boot/dts/armada-xp-mv78460.dtsi b/arch/arm/boot/dts/armada-xp-mv78460.dtsi index 36ce63a96cc9..661d54c81580 100644 --- a/arch/arm/boot/dts/armada-xp-mv78460.dtsi +++ b/arch/arm/boot/dts/armada-xp-mv78460.dtsi @@ -57,7 +57,6 @@ gpio0 = &gpio0; gpio1 = &gpio1; gpio2 = &gpio2; - eth3 = ð3; }; diff --git a/arch/arm/boot/dts/armada-xp-netgear-rn2120.dts b/arch/arm/boot/dts/armada-xp-netgear-rn2120.dts index 99cb9a8401b4..1516fc2627f9 100644 --- a/arch/arm/boot/dts/armada-xp-netgear-rn2120.dts +++ b/arch/arm/boot/dts/armada-xp-netgear-rn2120.dts @@ -53,7 +53,7 @@ compatible = "netgear,readynas-2120", "marvell,armadaxp-mv78230", "marvell,armadaxp", "marvell,armada-370-xp"; chosen { - bootargs = "console=ttyS0,115200 earlyprintk"; + stdout-path = "serial0:115200n8"; }; memory { diff --git a/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts b/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts index 0c76d9f05fd0..e3b08fb959e5 100644 --- a/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts +++ b/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts @@ -54,7 +54,7 @@ compatible = "plathome,openblocks-ax3-4", "marvell,armadaxp-mv78260", "marvell,armadaxp", "marvell,armada-370-xp"; chosen { - bootargs = "console=ttyS0,115200 earlyprintk"; + stdout-path = "serial0:115200n8"; }; memory { diff --git a/arch/arm/boot/dts/armada-xp-synology-ds414.dts b/arch/arm/boot/dts/armada-xp-synology-ds414.dts index e9fb225169aa..6063428fa6a0 100644 --- a/arch/arm/boot/dts/armada-xp-synology-ds414.dts +++ b/arch/arm/boot/dts/armada-xp-synology-ds414.dts @@ -67,8 +67,7 @@ "marvell,armadaxp", "marvell,armada-370-xp"; chosen { - bootargs = "console=ttyS0,115200 earlyprintk"; - stdout-path = &uart0; + stdout-path = "serial0:115200n8"; }; memory { diff --git a/arch/arm/boot/dts/armada-xp.dtsi b/arch/arm/boot/dts/armada-xp.dtsi index 82917236a2fb..ff47345e19ed 100644 --- a/arch/arm/boot/dts/armada-xp.dtsi +++ b/arch/arm/boot/dts/armada-xp.dtsi @@ -57,7 +57,8 @@ compatible = "marvell,armadaxp", "marvell,armada-370-xp"; aliases { - eth2 = ð2; + serial2 = &uart2; + serial3 = &uart3; }; soc { @@ -153,7 +154,7 @@ clocks = <&coreclk 1>; }; - interrupt-controller@20000 { + interrupt-controller@20a00 { reg = <0x20a00 0x2d0>, <0x21070 0x58>; }; diff --git a/arch/arm/boot/dts/at91-sama5d3_xplained.dts b/arch/arm/boot/dts/at91-sama5d3_xplained.dts index fec1fca2ad66..225c63d003d1 100644 --- a/arch/arm/boot/dts/at91-sama5d3_xplained.dts +++ b/arch/arm/boot/dts/at91-sama5d3_xplained.dts @@ -188,6 +188,11 @@ <AT91_PIOA 19 AT91_PERIPH_B AT91_PINCTRL_PULL_UP>; }; + pinctrl_key_gpio: key_gpio_0 { + atmel,pins = + <AT91_PIOE 29 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; + }; + pinctrl_mmc0_cd: mmc0_cd { atmel,pins = <AT91_PIOE 0 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; @@ -276,6 +281,9 @@ gpio_keys { compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_key_gpio>; + bp3 { label = "PB_USER"; gpios = <&pioE 29 GPIO_ACTIVE_LOW>; diff --git a/arch/arm/boot/dts/at91-sama5d4_xplained.dts b/arch/arm/boot/dts/at91-sama5d4_xplained.dts new file mode 100644 index 000000000000..c740e1a2a3a5 --- /dev/null +++ b/arch/arm/boot/dts/at91-sama5d4_xplained.dts @@ -0,0 +1,241 @@ +/* + * at91-sama5d4_xplained.dts - Device Tree file for SAMA5D4 Xplained board + * + * Copyright (C) 2015 Atmel, + * 2015 Josh Wu <[email protected]> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ +/dts-v1/; +#include "sama5d4.dtsi" + +/ { + model = "Atmel SAMA5D4 Xplained"; + compatible = "atmel,sama5d4-xplained", "atmel,sama5d4", "atmel,sama5"; + + chosen { + bootargs = "console=ttyS0,115200 ignore_loglevel earlyprintk"; + }; + + memory { + reg = <0x20000000 0x20000000>; + }; + + clocks { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + main_clock: clock@0 { + compatible = "atmel,osc", "fixed-clock"; + clock-frequency = <12000000>; + }; + + slow_xtal { + clock-frequency = <32768>; + }; + + main_xtal { + clock-frequency = <12000000>; + }; + }; + + ahb { + apb { + spi0: spi@f8010000 { + cs-gpios = <&pioC 3 0>, <0>, <0>, <0>; + status = "okay"; + m25p80@0 { + compatible = "atmel,at25df321a"; + spi-max-frequency = <50000000>; + reg = <0>; + }; + }; + + i2c0: i2c@f8014000 { + status = "okay"; + }; + + macb0: ethernet@f8020000 { + phy-mode = "rmii"; + status = "okay"; + + phy0: ethernet-phy@1 { + interrupt-parent = <&pioE>; + interrupts = <1 IRQ_TYPE_EDGE_FALLING>; + reg = <1>; + }; + }; + + mmc1: mmc@fc000000 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3 &pinctrl_mmc1_cd>; + status = "okay"; + slot@0 { + reg = <0>; + bus-width = <4>; + cd-gpios = <&pioE 3 0>; + }; + }; + + usart3: serial@fc00c000 { + status = "okay"; + }; + + usart4: serial@fc010000 { + status = "okay"; + }; + + adc0: adc@fc034000 { + atmel,adc-vref = <3300>; + status = "okay"; + }; + + watchdog@fc068640 { + status = "okay"; + }; + + pinctrl@fc06a000 { + board { + pinctrl_mmc1_cd: mmc1_cd { + atmel,pins = + <AT91_PIOE 3 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; + }; + pinctrl_usba_vbus: usba_vbus { + atmel,pins = + <AT91_PIOE 31 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>; + }; + pinctrl_key_gpio: key_gpio_0 { + atmel,pins = + <AT91_PIOE 8 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; + }; + }; + }; + }; + + usb0: gadget@00400000 { + atmel,vbus-gpio = <&pioE 31 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usba_vbus>; + status = "okay"; + }; + + usb1: ohci@00500000 { + num-ports = <3>; + atmel,vbus-gpio = <0 + &pioE 11 GPIO_ACTIVE_HIGH + &pioE 14 GPIO_ACTIVE_HIGH + >; + status = "okay"; + }; + + usb2: ehci@00600000 { + status = "okay"; + }; + + nand0: nand@80000000 { + nand-bus-width = <8>; + nand-ecc-mode = "hw"; + nand-on-flash-bbt; + atmel,has-pmecc; + status = "okay"; + + at91bootstrap@0 { + label = "at91bootstrap"; + reg = <0x0 0x40000>; + }; + + bootloader@40000 { + label = "bootloader"; + reg = <0x40000 0x80000>; + }; + + bootloaderenv@c0000 { + label = "bootloader env"; + reg = <0xc0000 0xc0000>; + }; + + dtb@180000 { + label = "device tree"; + reg = <0x180000 0x80000>; + }; + + kernel@200000 { + label = "kernel"; + reg = <0x200000 0x600000>; + }; + + rootfs@800000 { + label = "rootfs"; + reg = <0x800000 0x0f800000>; + }; + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_key_gpio>; + + pb_user1 { + label = "pb_user1"; + gpios = <&pioE 8 GPIO_ACTIVE_HIGH>; + linux,code = <0x100>; + gpio-key,wakeup; + }; + }; + + leds { + compatible = "gpio-leds"; + status = "okay"; + + d8 { + label = "d8"; + gpios = <&pioD 30 GPIO_ACTIVE_HIGH>; + status = "disabled"; + }; + + d10 { + label = "d10"; + gpios = <&pioE 15 GPIO_ACTIVE_LOW>; + linux,default-trigger = "heartbeat"; + }; + }; +}; diff --git a/arch/arm/boot/dts/at91-sama5d4ek.dts b/arch/arm/boot/dts/at91-sama5d4ek.dts index 9198b719d0ef..89ef4a540db5 100644 --- a/arch/arm/boot/dts/at91-sama5d4ek.dts +++ b/arch/arm/boot/dts/at91-sama5d4ek.dts @@ -115,6 +115,10 @@ }; }; + ssc0: ssc@f8008000 { + status = "okay"; + }; + spi0: spi@f8010000 { cs-gpios = <&pioC 3 0>, <0>, <0>, <0>; status = "okay"; @@ -127,6 +131,13 @@ i2c0: i2c@f8014000 { status = "okay"; + + wm8904: codec@1a { + compatible = "wlf,wm8904"; + reg = <0x1a>; + clocks = <&pck2>; + clock-names = "mclk"; + }; }; macb0: ethernet@f8020000 { @@ -171,6 +182,10 @@ atmel,pins = <AT91_PIOE 6 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; }; + pinctrl_pck2_as_audio_mck: pck2_as_audio_mck { + atmel,pins = + <AT91_PIOB 10 AT91_PERIPH_B AT91_PINCTRL_NONE>; + }; pinctrl_usba_vbus: usba_vbus { atmel,pins = <AT91_PIOE 31 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>; @@ -244,8 +259,6 @@ gpio_keys { compatible = "gpio-keys"; - #address-cells = <1>; - #size-cells = <0>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_key_gpio>; @@ -257,4 +270,42 @@ gpio-key,wakeup; }; }; + + leds { + compatible = "gpio-leds"; + status = "okay"; + + d8 { + label = "d8"; + /* PE28, conflicts with usart4 rts pin */ + gpios = <&pioE 28 GPIO_ACTIVE_LOW>; + }; + + d9 { + label = "d9"; + gpios = <&pioE 9 GPIO_ACTIVE_HIGH>; + }; + + d10 { + label = "d10"; + gpios = <&pioE 8 GPIO_ACTIVE_LOW>; + linux,default-trigger = "heartbeat"; + }; + }; + + sound { + compatible = "atmel,asoc-wm8904"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pck2_as_audio_mck>; + + atmel,model = "wm8904 @ SAMA5D4EK"; + atmel,audio-routing = + "Headphone Jack", "HPOUTL", + "Headphone Jack", "HPOUTR", + "IN1L", "Line In Jack", + "IN1R", "Line In Jack"; + + atmel,ssc-controller = <&ssc0>; + atmel,audio-codec = <&wm8904>; + }; }; diff --git a/arch/arm/boot/dts/at91sam9260.dtsi b/arch/arm/boot/dts/at91sam9260.dtsi index fff0ee69aab4..ac2c5dd03663 100644 --- a/arch/arm/boot/dts/at91sam9260.dtsi +++ b/arch/arm/boot/dts/at91sam9260.dtsi @@ -494,12 +494,12 @@ pinctrl_usart3_rts: usart3_rts-0 { atmel,pins = - <AT91_PIOB 8 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PC8 periph B */ + <AT91_PIOC 8 AT91_PERIPH_B AT91_PINCTRL_NONE>; }; pinctrl_usart3_cts: usart3_cts-0 { atmel,pins = - <AT91_PIOB 10 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PC10 periph B */ + <AT91_PIOC 10 AT91_PERIPH_B AT91_PINCTRL_NONE>; }; }; @@ -976,7 +976,6 @@ atmel,watchdog-type = "hardware"; atmel,reset-type = "all"; atmel,dbg-halt; - atmel,idle-halt; status = "disabled"; }; diff --git a/arch/arm/boot/dts/at91sam9263.dtsi b/arch/arm/boot/dts/at91sam9263.dtsi index 1f67bb4c144e..088219d1c8ce 100644 --- a/arch/arm/boot/dts/at91sam9263.dtsi +++ b/arch/arm/boot/dts/at91sam9263.dtsi @@ -69,7 +69,7 @@ sram1: sram@00500000 { compatible = "mmio-sram"; - reg = <0x00300000 0x4000>; + reg = <0x00500000 0x4000>; }; ahb { @@ -905,7 +905,6 @@ atmel,watchdog-type = "hardware"; atmel,reset-type = "all"; atmel,dbg-halt; - atmel,idle-halt; status = "disabled"; }; diff --git a/arch/arm/boot/dts/at91sam9g25.dtsi b/arch/arm/boot/dts/at91sam9g25.dtsi index 17b879990914..a7da0dd0c98f 100644 --- a/arch/arm/boot/dts/at91sam9g25.dtsi +++ b/arch/arm/boot/dts/at91sam9g25.dtsi @@ -7,6 +7,7 @@ */ #include "at91sam9x5.dtsi" +#include "at91sam9x5_isi.dtsi" #include "at91sam9x5_usart3.dtsi" #include "at91sam9x5_macb0.dtsi" diff --git a/arch/arm/boot/dts/at91sam9g25ek.dts b/arch/arm/boot/dts/at91sam9g25ek.dts index 1e4c49c584d3..707fd4ea58f5 100644 --- a/arch/arm/boot/dts/at91sam9g25ek.dts +++ b/arch/arm/boot/dts/at91sam9g25ek.dts @@ -16,10 +16,28 @@ ahb { apb { + spi0: spi@f0000000 { + status = "disabled"; + }; + + mmc1: mmc@f000c000 { + status = "disabled"; + }; + + i2c0: i2c@f8010000 { + ov2640: camera@0x30 { + status = "okay"; + }; + }; + macb0: ethernet@f802c000 { phy-mode = "rmii"; status = "okay"; }; + + isi: isi@f8048000 { + status = "okay"; + }; }; }; }; diff --git a/arch/arm/boot/dts/at91sam9g45.dtsi b/arch/arm/boot/dts/at91sam9g45.dtsi index ee80aa9c0759..119893181189 100644 --- a/arch/arm/boot/dts/at91sam9g45.dtsi +++ b/arch/arm/boot/dts/at91sam9g45.dtsi @@ -1116,7 +1116,6 @@ atmel,watchdog-type = "hardware"; atmel,reset-type = "all"; atmel,dbg-halt; - atmel,idle-halt; status = "disabled"; }; diff --git a/arch/arm/boot/dts/at91sam9n12.dtsi b/arch/arm/boot/dts/at91sam9n12.dtsi index c2666a7cb5b1..9648430d78e6 100644 --- a/arch/arm/boot/dts/at91sam9n12.dtsi +++ b/arch/arm/boot/dts/at91sam9n12.dtsi @@ -894,7 +894,6 @@ atmel,watchdog-type = "hardware"; atmel,reset-type = "all"; atmel,dbg-halt; - atmel,idle-halt; status = "disabled"; }; @@ -913,6 +912,15 @@ clocks = <&pwm_clk>; status = "disabled"; }; + + usb1: gadget@f803c000 { + compatible = "atmel,at91sam9260-udc"; + reg = <0xf803c000 0x4000>; + interrupts = <23 IRQ_TYPE_LEVEL_HIGH 2>; + clocks = <&udphs_clk>, <&udpck>; + clock-names = "pclk", "hclk"; + status = "disabled"; + }; }; nand0: nand@40000000 { diff --git a/arch/arm/boot/dts/at91sam9n12ek.dts b/arch/arm/boot/dts/at91sam9n12ek.dts index 9575c0d895c9..6123109f14ff 100644 --- a/arch/arm/boot/dts/at91sam9n12ek.dts +++ b/arch/arm/boot/dts/at91sam9n12ek.dts @@ -108,6 +108,13 @@ <AT91_PIOB 10 AT91_PERIPH_B AT91_PINCTRL_NONE>; }; }; + + usb1 { + pinctrl_usb1_vbus_sense: usb1_vbus_sense { + atmel,pins = + <AT91_PIOB 16 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>; /* PB16 gpio usb vbus sense, no pull up and deglitch */ + }; + }; }; spi0: spi@f0000000 { @@ -120,6 +127,13 @@ }; }; + usb1: gadget@f803c000 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb1_vbus_sense>; + atmel,vbus-gpio = <&pioB 16 GPIO_ACTIVE_HIGH>; + status = "okay"; + }; + watchdog@fffffe40 { status = "okay"; }; diff --git a/arch/arm/boot/dts/at91sam9x5.dtsi b/arch/arm/boot/dts/at91sam9x5.dtsi index 818dabdd8c0e..e77c9bb5485d 100644 --- a/arch/arm/boot/dts/at91sam9x5.dtsi +++ b/arch/arm/boot/dts/at91sam9x5.dtsi @@ -1130,7 +1130,6 @@ atmel,watchdog-type = "hardware"; atmel,reset-type = "all"; atmel,dbg-halt; - atmel,idle-halt; status = "disabled"; }; diff --git a/arch/arm/boot/dts/at91sam9x5_isi.dtsi b/arch/arm/boot/dts/at91sam9x5_isi.dtsi index 98bc877a68ef..8fc45ca4dcb5 100644 --- a/arch/arm/boot/dts/at91sam9x5_isi.dtsi +++ b/arch/arm/boot/dts/at91sam9x5_isi.dtsi @@ -13,6 +13,37 @@ / { ahb { apb { + pinctrl@fffff400 { + isi { + pinctrl_isi_data_0_7: isi-0-data-0-7 { + atmel,pins = + <AT91_PIOC 0 AT91_PERIPH_B AT91_PINCTRL_NONE /* ISI_D0, conflicts with LCDDAT0 */ + AT91_PIOC 1 AT91_PERIPH_B AT91_PINCTRL_NONE /* ISI_D1, conflicts with LCDDAT1 */ + AT91_PIOC 2 AT91_PERIPH_B AT91_PINCTRL_NONE /* ISI_D2, conflicts with LCDDAT2 */ + AT91_PIOC 3 AT91_PERIPH_B AT91_PINCTRL_NONE /* ISI_D3, conflicts with LCDDAT3 */ + AT91_PIOC 4 AT91_PERIPH_B AT91_PINCTRL_NONE /* ISI_D4, conflicts with LCDDAT4 */ + AT91_PIOC 5 AT91_PERIPH_B AT91_PINCTRL_NONE /* ISI_D5, conflicts with LCDDAT5 */ + AT91_PIOC 6 AT91_PERIPH_B AT91_PINCTRL_NONE /* ISI_D6, conflicts with LCDDAT6 */ + AT91_PIOC 7 AT91_PERIPH_B AT91_PINCTRL_NONE /* ISI_D7, conflicts with LCDDAT7 */ + AT91_PIOC 12 AT91_PERIPH_B AT91_PINCTRL_NONE /* ISI_PCK, conflicts with LCDDAT12 */ + AT91_PIOC 14 AT91_PERIPH_B AT91_PINCTRL_NONE /* ISI_HSYNC, conflicts with LCDDAT14 */ + AT91_PIOC 13 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* ISI_VSYNC, conflicts with LCDDAT13 */ + }; + + pinctrl_isi_data_8_9: isi-0-data-8-9 { + atmel,pins = + <AT91_PIOC 8 AT91_PERIPH_B AT91_PINCTRL_NONE /* ISI_D8, conflicts with LCDDAT8 */ + AT91_PIOC 9 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* ISI_D9, conflicts with LCDDAT9 */ + }; + + pinctrl_isi_data_10_11: isi-0-data-10-11 { + atmel,pins = + <AT91_PIOC 10 AT91_PERIPH_B AT91_PINCTRL_NONE /* ISI_D10, conflicts with LCDDAT10 */ + AT91_PIOC 11 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* ISI_D11, conflicts with LCDDAT11 */ + }; + }; + }; + pmc: pmc@fffffc00 { periphck { isi_clk: isi_clk { @@ -21,6 +52,21 @@ }; }; }; + + isi: isi@f8048000 { + compatible = "atmel,at91sam9g45-isi"; + reg = <0xf8048000 0x4000>; + interrupts = <25 IRQ_TYPE_LEVEL_HIGH 5>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_isi_data_0_7>; + clocks = <&isi_clk>; + clock-names = "isi_clk"; + status = "disabled"; + port { + #address-cells = <1>; + #size-cells = <0>; + }; + }; }; }; }; diff --git a/arch/arm/boot/dts/at91sam9x5ek.dtsi b/arch/arm/boot/dts/at91sam9x5ek.dtsi index bd16bd360272..cc83a37a7311 100644 --- a/arch/arm/boot/dts/at91sam9x5ek.dtsi +++ b/arch/arm/boot/dts/at91sam9x5ek.dtsi @@ -59,6 +59,16 @@ status = "okay"; }; + isi: isi@f8048000 { + status = "disabled"; + port { + isi_0: endpoint@0 { + remote-endpoint = <&ov2640_0>; + bus-width = <8>; + }; + }; + }; + i2c0: i2c@f8010000 { status = "okay"; @@ -66,9 +76,47 @@ compatible = "wm8731"; reg = <0x1a>; }; + + ov2640: camera@0x30 { + compatible = "ovti,ov2640"; + reg = <0x30>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pck0_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>; + resetb-gpios = <&pioA 7 GPIO_ACTIVE_LOW>; + pwdn-gpios = <&pioA 13 GPIO_ACTIVE_HIGH>; + clocks = <&pck0>; + clock-names = "xvclk"; + assigned-clocks = <&pck0>; + assigned-clock-rates = <25000000>; + status = "disabled"; + + port { + ov2640_0: endpoint { + remote-endpoint = <&isi_0>; + bus-width = <8>; + }; + }; + }; }; pinctrl@fffff400 { + camera_sensor { + pinctrl_pck0_as_isi_mck: pck0_as_isi_mck-0 { + atmel,pins = + <AT91_PIOC 15 AT91_PERIPH_C AT91_PINCTRL_NONE>; /* ISI_MCK */ + }; + + pinctrl_sensor_power: sensor_power-0 { + atmel,pins = + <AT91_PIOA 13 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>; + }; + + pinctrl_sensor_reset: sensor_reset-0 { + atmel,pins = + <AT91_PIOA 7 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>; + }; + }; + mmc0 { pinctrl_board_mmc0: mmc0-board { atmel,pins = diff --git a/arch/arm/boot/dts/bcm-cygnus.dtsi b/arch/arm/boot/dts/bcm-cygnus.dtsi index ff5fb6ab0b97..7b52c33ea69a 100644 --- a/arch/arm/boot/dts/bcm-cygnus.dtsi +++ b/arch/arm/boot/dts/bcm-cygnus.dtsi @@ -54,6 +54,42 @@ /include/ "bcm-cygnus-clock.dtsi" + pinctrl: pinctrl@0x0301d0c8 { + compatible = "brcm,cygnus-pinmux"; + reg = <0x0301d0c8 0x30>, + <0x0301d24c 0x2c>; + }; + + gpio_crmu: gpio@03024800 { + compatible = "brcm,cygnus-crmu-gpio"; + reg = <0x03024800 0x50>, + <0x03024008 0x18>; + #gpio-cells = <2>; + gpio-controller; + }; + + gpio_ccm: gpio@1800a000 { + compatible = "brcm,cygnus-ccm-gpio"; + reg = <0x1800a000 0x50>, + <0x0301d164 0x20>; + #gpio-cells = <2>; + gpio-controller; + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; + interrupt-controller; + }; + + gpio_asiu: gpio@180a5000 { + compatible = "brcm,cygnus-asiu-gpio"; + reg = <0x180a5000 0x668>; + #gpio-cells = <2>; + gpio-controller; + + pinmux = <&pinctrl>; + + interrupt-controller; + interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>; + }; + amba { #address-cells = <1>; #size-cells = <1>; @@ -90,6 +126,48 @@ status = "disabled"; }; + pcie0: pcie@18012000 { + compatible = "brcm,iproc-pcie"; + reg = <0x18012000 0x1000>; + + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 100 IRQ_TYPE_NONE>; + + linux,pci-domain = <0>; + + bus-range = <0x00 0xff>; + + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x81000000 0 0 0x28000000 0 0x00010000 + 0x82000000 0 0x20000000 0x20000000 0 0x04000000>; + + status = "disabled"; + }; + + pcie1: pcie@18013000 { + compatible = "brcm,iproc-pcie"; + reg = <0x18013000 0x1000>; + + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 106 IRQ_TYPE_NONE>; + + linux,pci-domain = <1>; + + bus-range = <0x00 0xff>; + + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x81000000 0 0 0x48000000 0 0x00010000 + 0x82000000 0 0x40000000 0x40000000 0 0x04000000>; + + status = "disabled"; + }; + uart0: serial@18020000 { compatible = "snps,dw-apb-uart"; reg = <0x18020000 0x100>; diff --git a/arch/arm/boot/dts/bcm4708-netgear-r6250.dts b/arch/arm/boot/dts/bcm4708-netgear-r6250.dts index f18c9d9b2f2c..2ed9e5794785 100644 --- a/arch/arm/boot/dts/bcm4708-netgear-r6250.dts +++ b/arch/arm/boot/dts/bcm4708-netgear-r6250.dts @@ -45,13 +45,13 @@ power0 { label = "bcm53xx:green:power"; gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>; - linux,default-trigger = "default-off"; + linux,default-trigger = "default-on"; }; power1 { label = "bcm53xx:amber:power"; gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>; - linux,default-trigger = "default-on"; + linux,default-trigger = "default-off"; }; usb { diff --git a/arch/arm/boot/dts/bcm4709-netgear-r8000.dts b/arch/arm/boot/dts/bcm4709-netgear-r8000.dts new file mode 100644 index 000000000000..ea26dd3ec03a --- /dev/null +++ b/arch/arm/boot/dts/bcm4709-netgear-r8000.dts @@ -0,0 +1,77 @@ +/* + * Broadcom BCM470X / BCM5301X ARM platform code. + * DTS for Netgear R8000 + * + * Copyright (C) 2015 Rafał Miłecki <[email protected]> + * + * Licensed under the GNU/GPL. See COPYING for details. + */ + +/dts-v1/; + +#include "bcm4708.dtsi" + +/ { + compatible = "netgear,r8000", "brcm,bcm4709", "brcm,bcm4708"; + model = "Netgear R8000 (BCM4709)"; + + chosen { + bootargs = "console=ttyS0,115200"; + }; + + memory { + reg = <0x00000000 0x08000000>; + }; + + leds { + compatible = "gpio-leds"; + + power0 { + label = "bcm53xx:white:power"; + gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>; + linux,default-trigger = "default-on"; + }; + + power1 { + label = "bcm53xx:amber:power"; + gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>; + linux,default-trigger = "default-off"; + }; + + 5ghz-1 { + label = "bcm53xx:white:5ghz-1"; + gpios = <&chipcommon 12 GPIO_ACTIVE_LOW>; + linux,default-trigger = "default-off"; + }; + + 2ghz { + label = "bcm53xx:white:2ghz"; + gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>; + linux,default-trigger = "default-off"; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + + rfkill { + label = "WiFi"; + linux,code = <KEY_RFKILL>; + gpios = <&chipcommon 4 GPIO_ACTIVE_LOW>; + }; + + wps { + label = "WPS"; + linux,code = <KEY_WPS_BUTTON>; + gpios = <&chipcommon 5 GPIO_ACTIVE_LOW>; + }; + + restart { + label = "Reset"; + linux,code = <KEY_RESTART>; + gpios = <&chipcommon 6 GPIO_ACTIVE_LOW>; + }; + }; +}; diff --git a/arch/arm/boot/dts/bcm911360_entphn.dts b/arch/arm/boot/dts/bcm911360_entphn.dts index d2ee95280548..7db484323fd6 100644 --- a/arch/arm/boot/dts/bcm911360_entphn.dts +++ b/arch/arm/boot/dts/bcm911360_entphn.dts @@ -33,6 +33,7 @@ /dts-v1/; #include "bcm-cygnus.dtsi" +#include "dt-bindings/input/input.h" / { model = "Cygnus Enterprise Phone (BCM911360_ENTPHN)"; @@ -50,4 +51,16 @@ uart3: serial@18023000 { status = "okay"; }; + + gpio_keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + + hook { + label = "HOOK"; + linux,code = <KEY_O>; + gpios = <&gpio_asiu 48 0>; + }; + }; }; diff --git a/arch/arm/boot/dts/bcm958300k.dts b/arch/arm/boot/dts/bcm958300k.dts index f1bb36f3975c..c9eb8565eac5 100644 --- a/arch/arm/boot/dts/bcm958300k.dts +++ b/arch/arm/boot/dts/bcm958300k.dts @@ -47,6 +47,14 @@ bootargs = "console=ttyS0,115200"; }; + pcie0: pcie@18012000 { + status = "okay"; + }; + + pcie1: pcie@18013000 { + status = "okay"; + }; + uart3: serial@18023000 { status = "okay"; }; diff --git a/arch/arm/boot/dts/bcm958305k.dts b/arch/arm/boot/dts/bcm958305k.dts new file mode 100644 index 000000000000..56b429abbedb --- /dev/null +++ b/arch/arm/boot/dts/bcm958305k.dts @@ -0,0 +1,53 @@ +/* + * BSD LICENSE + * + * Copyright(c) 2015 Broadcom Corporation. All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * * Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * * Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * * Neither the name of Broadcom Corporation nor the names of its + * contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, + * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT + * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, + * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY + * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + */ + +/dts-v1/; + +#include "bcm-cygnus.dtsi" + +/ { + model = "Cygnus Wireless Audio (BCM958305K)"; + compatible = "brcm,bcm58305", "brcm,cygnus"; + + aliases { + serial0 = &uart3; + }; + + chosen { + stdout-path = &uart3; + bootargs = "console=ttyS0,115200"; + }; + + uart3: serial@18023000 { + status = "okay"; + }; +}; diff --git a/arch/arm/boot/dts/dove.dtsi b/arch/arm/boot/dts/dove.dtsi index a5441d5482a6..9ad829523a13 100644 --- a/arch/arm/boot/dts/dove.dtsi +++ b/arch/arm/boot/dts/dove.dtsi @@ -1,5 +1,8 @@ /include/ "skeleton.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/interrupt-controller/irq.h> + #define MBUS_ID(target,attributes) (((target) << 24) | ((attributes) << 16)) / { @@ -61,7 +64,7 @@ 0x82000000 0x2 0x0 MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 1.0 Mem */ 0x81000000 0x2 0x0 MBUS_ID(0x08, 0xe0) 0 1 0>; /* Port 1.0 I/O */ - pcie-port@0 { + pcie0: pcie-port@0 { device_type = "pci"; status = "disabled"; assigned-addresses = <0x82000800 0 0x40000 0 0x2000>; @@ -79,7 +82,7 @@ interrupt-map = <0 0 0 0 &intc 16>; }; - pcie-port@1 { + pcie1: pcie-port@1 { device_type = "pci"; status = "disabled"; assigned-addresses = <0x82002800 0 0x80000 0 0x2000>; @@ -154,7 +157,7 @@ uart2: serial@12200 { compatible = "ns16550a"; - reg = <0x12000 0x100>; + reg = <0x12200 0x100>; reg-shift = <2>; interrupts = <9>; clocks = <&core_clk 0>; @@ -163,7 +166,7 @@ uart3: serial@12300 { compatible = "ns16550a"; - reg = <0x12100 0x100>; + reg = <0x12300 0x100>; reg-shift = <2>; interrupts = <10>; clocks = <&core_clk 0>; @@ -448,6 +451,11 @@ marvell,function = "gpio"; }; + pmx_pcie1_clkreq: pmx-pcie1-clkreq { + marvell,pins = "mpp9"; + marvell,function = "pex1"; + }; + pmx_gpio_10: pmx-gpio-10 { marvell,pins = "mpp10"; marvell,function = "gpio"; @@ -458,6 +466,11 @@ marvell,function = "gpio"; }; + pmx_pcie0_clkreq: pmx-pcie0-clkreq { + marvell,pins = "mpp11"; + marvell,function = "pex0"; + }; + pmx_gpio_12: pmx-gpio-12 { marvell,pins = "mpp12"; marvell,function = "gpio"; @@ -563,6 +576,18 @@ marvell,function = "gpio"; }; + pmx_spi1_4_7: pmx-spi1-4-7 { + marvell,pins = "mpp4", "mpp5", + "mpp6", "mpp7"; + marvell,function = "spi1"; + }; + + pmx_spi1_20_23: pmx-spi1-20-23 { + marvell,pins = "mpp20", "mpp21", + "mpp22", "mpp23"; + marvell,function = "spi1"; + }; + pmx_uart1: pmx-uart1 { marvell,pins = "mpp_uart1"; marvell,function = "uart1"; @@ -582,6 +607,36 @@ marvell,pins = "mpp_nand"; marvell,function = "gpo"; }; + + pmx_i2c1: pmx-i2c1 { + marvell,pins = "mpp17", "mpp19"; + marvell,function = "twsi"; + }; + + pmx_i2c2: pmx-i2c2 { + marvell,pins = "mpp_audio1"; + marvell,function = "twsi"; + }; + + pmx_ssp_i2c2: pmx-ssp-i2c2 { + marvell,pins = "mpp_audio1"; + marvell,function = "ssp/twsi"; + }; + + pmx_i2cmux_0: pmx-i2cmux-0 { + marvell,pins = "twsi"; + marvell,function = "twsi-opt1"; + }; + + pmx_i2cmux_1: pmx-i2cmux-1 { + marvell,pins = "twsi"; + marvell,function = "twsi-opt2"; + }; + + pmx_i2cmux_2: pmx-i2cmux-2 { + marvell,pins = "twsi"; + marvell,function = "twsi-opt3"; + }; }; core_clk: core-clocks@d0214 { diff --git a/arch/arm/boot/dts/emev2-kzm9d.dts b/arch/arm/boot/dts/emev2-kzm9d.dts index 667d323e80a3..19446273e4a7 100644 --- a/arch/arm/boot/dts/emev2-kzm9d.dts +++ b/arch/arm/boot/dts/emev2-kzm9d.dts @@ -94,3 +94,16 @@ vdd33a-supply = <®_3p3v>; }; }; + +&pfc { + uart1_pins: uart@e1030000 { + renesas,groups = "uart1_ctrl", "uart1_data"; + renesas,function = "uart1"; + }; +}; + +&uart1 { + pinctrl-0 = <&uart1_pins>; + pinctrl-names = "default"; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/emev2.dtsi b/arch/arm/boot/dts/emev2.dtsi index cc7bfe0ba40a..bb45694d91bc 100644 --- a/arch/arm/boot/dts/emev2.dtsi +++ b/arch/arm/boot/dts/emev2.dtsi @@ -169,12 +169,18 @@ clock-names = "sclk"; }; + pfc: pfc@e0140200 { + compatible = "renesas,pfc-emev2"; + reg = <0xe0140200 0x100>; + }; + gpio0: gpio@e0050000 { compatible = "renesas,em-gio"; reg = <0xe0050000 0x2c>, <0xe0050040 0x20>; interrupts = <0 67 IRQ_TYPE_LEVEL_HIGH>, <0 68 IRQ_TYPE_LEVEL_HIGH>; gpio-controller; + gpio-ranges = <&pfc 0 0 32>; #gpio-cells = <2>; ngpios = <32>; interrupt-controller; @@ -186,6 +192,7 @@ interrupts = <0 69 IRQ_TYPE_LEVEL_HIGH>, <0 70 IRQ_TYPE_LEVEL_HIGH>; gpio-controller; + gpio-ranges = <&pfc 0 32 32>; #gpio-cells = <2>; ngpios = <32>; interrupt-controller; @@ -197,6 +204,7 @@ interrupts = <0 71 IRQ_TYPE_LEVEL_HIGH>, <0 72 IRQ_TYPE_LEVEL_HIGH>; gpio-controller; + gpio-ranges = <&pfc 0 64 32>; #gpio-cells = <2>; ngpios = <32>; interrupt-controller; @@ -208,6 +216,7 @@ interrupts = <0 73 IRQ_TYPE_LEVEL_HIGH>, <0 74 IRQ_TYPE_LEVEL_HIGH>; gpio-controller; + gpio-ranges = <&pfc 0 96 32>; #gpio-cells = <2>; ngpios = <32>; interrupt-controller; @@ -219,6 +228,7 @@ interrupts = <0 75 IRQ_TYPE_LEVEL_HIGH>, <0 76 IRQ_TYPE_LEVEL_HIGH>; gpio-controller; + gpio-ranges = <&pfc 0 128 31>; #gpio-cells = <2>; ngpios = <31>; interrupt-controller; diff --git a/arch/arm/boot/dts/kirkwood-net2big.dts b/arch/arm/boot/dts/kirkwood-net2big.dts index 53dc37a3b687..13a44773b6df 100644 --- a/arch/arm/boot/dts/kirkwood-net2big.dts +++ b/arch/arm/boot/dts/kirkwood-net2big.dts @@ -27,6 +27,11 @@ device_type = "memory"; reg = <0x00000000 0x10000000>; }; + + fan { + compatible = "gpio-fan"; + alarm-gpios = <&gpio0 25 GPIO_ACTIVE_LOW>; + }; }; ®ulators { diff --git a/arch/arm/boot/dts/meson.dtsi b/arch/arm/boot/dts/meson.dtsi index b67ede515bcd..548441384d2a 100644 --- a/arch/arm/boot/dts/meson.dtsi +++ b/arch/arm/boot/dts/meson.dtsi @@ -150,5 +150,25 @@ interrupts = <0 15 1>; status = "disabled"; }; + + spifc: spi@c1108c80 { + compatible = "amlogic,meson6-spifc"; + reg = <0xc1108c80 0x80>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clk81>; + status = "disabled"; + }; + + ethmac: ethernet@c9410000 { + compatible = "amlogic,meson6-dwmac", "snps,dwmac"; + reg = <0xc9410000 0x10000 + 0xc1108108 0x4>; + interrupts = <0 8 1>; + interrupt-names = "macirq"; + clocks = <&clk81>; + clock-names = "stmmaceth"; + status = "disabled"; + }; }; }; /* end of / */ diff --git a/arch/arm/boot/dts/meson6-atv1200.dts b/arch/arm/boot/dts/meson6-atv1200.dts index d7d351a68944..1237faa63ce6 100644 --- a/arch/arm/boot/dts/meson6-atv1200.dts +++ b/arch/arm/boot/dts/meson6-atv1200.dts @@ -64,3 +64,7 @@ &uart_AO { status = "okay"; }; + +ðmac { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/meson8-minix-neo-x8.dts b/arch/arm/boot/dts/meson8-minix-neo-x8.dts new file mode 100644 index 000000000000..4f536bb1f002 --- /dev/null +++ b/arch/arm/boot/dts/meson8-minix-neo-x8.dts @@ -0,0 +1,128 @@ +/* + * Copyright 2014 Beniamino Galvani <[email protected]> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This library is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This library is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include <dt-bindings/gpio/gpio.h> +#include "meson8.dtsi" + +/ { + model = "MINIX NEO-X8"; + compatible = "minix,neo-x8", "amlogic,meson8"; + + aliases { + serial0 = &uart_AO; + }; + + memory { + reg = <0x40000000 0x80000000>; + }; + + gpio-leds { + compatible = "gpio-leds"; + + blue { + label = "x8:blue:power"; + gpios = <&gpio_ao GPIO_TEST_N GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&uart_AO { + status = "okay"; + pinctrl-0 = <&uart_ao_a_pins>; + pinctrl-names = "default"; +}; + +&i2c_AO { + status = "okay"; + pinctrl-0 = <&i2c_ao_pins>; + pinctrl-names = "default"; + + pmic@32 { + compatible = "ricoh,rn5t618"; + reg = <0x32>; + + regulators { + }; + }; + + rtc@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + }; +}; + +&spifc { + status = "okay"; + pinctrl-0 = <&spi_nor_pins>; + pinctrl-names = "default"; + + spi-flash@0 { + compatible = "mxicy,mx25l1606e"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0>; + spi-max-frequency = <30000000>; + + partition@0 { + label = "boot"; + reg = <0x0 0x100000>; + }; + + partition@100000 { + label = "env"; + reg = <0x100000 0x10000>; + }; + }; +}; + +&ir_receiver { + status = "okay"; + pinctrl-0 = <&ir_recv_pins>; + pinctrl-names = "default"; +}; + +ðmac { + status = "okay"; + pinctrl-0 = <ð_pins>; + pnictrl-names = "default"; +}; diff --git a/arch/arm/boot/dts/meson8.dtsi b/arch/arm/boot/dts/meson8.dtsi index 1f442a7fe03b..a2ddcb8c545a 100644 --- a/arch/arm/boot/dts/meson8.dtsi +++ b/arch/arm/boot/dts/meson8.dtsi @@ -43,6 +43,7 @@ * OTHER DEALINGS IN THE SOFTWARE. */ +#include <dt-bindings/gpio/meson8-gpio.h> /include/ "meson.dtsi" / { @@ -89,4 +90,71 @@ compatible = "fixed-clock"; clock-frequency = <141666666>; }; + + pinctrl: pinctrl@c1109880 { + compatible = "amlogic,meson8-pinctrl"; + reg = <0xc1109880 0x10>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + gpio: banks@c11080b0 { + reg = <0xc11080b0 0x28>, + <0xc11080e8 0x18>, + <0xc1108120 0x18>, + <0xc1108030 0x30>; + reg-names = "mux", "pull", "pull-enable", "gpio"; + gpio-controller; + #gpio-cells = <2>; + }; + + gpio_ao: ao-bank@c1108030 { + reg = <0xc8100014 0x4>, + <0xc810002c 0x4>, + <0xc8100024 0x8>; + reg-names = "mux", "pull", "gpio"; + gpio-controller; + #gpio-cells = <2>; + }; + + uart_ao_a_pins: uart_ao_a { + mux { + groups = "uart_tx_ao_a", "uart_rx_ao_a"; + function = "uart_ao"; + }; + }; + + i2c_ao_pins: i2c_mst_ao { + mux { + groups = "i2c_mst_sck_ao", "i2c_mst_sda_ao"; + function = "i2c_mst_ao"; + }; + }; + + spi_nor_pins: nor { + mux { + groups = "nor_d", "nor_q", "nor_c", "nor_cs"; + function = "nor"; + }; + }; + + ir_recv_pins: remote { + mux { + groups = "remote_input"; + function = "remote"; + }; + }; + + eth_pins: ethernet { + mux { + groups = "eth_tx_clk_50m", "eth_tx_en", + "eth_txd1", "eth_txd0", + "eth_rx_clk_in", "eth_rx_dv", + "eth_rxd1", "eth_rxd0", "eth_mdio", + "eth_mdc"; + function = "ethernet"; + }; + }; + }; + }; /* end of / */ diff --git a/arch/arm/boot/dts/nspire-classic.dtsi b/arch/arm/boot/dts/nspire-classic.dtsi index 9565199bce7a..4907c5085d4b 100644 --- a/arch/arm/boot/dts/nspire-classic.dtsi +++ b/arch/arm/boot/dts/nspire-classic.dtsi @@ -51,6 +51,11 @@ compatible = "lsi,nspire-classic-ahb-divider"; }; + +&vbus_reg { + gpio = <&gpio 5 0>; +}; + / { memory { device_type = "memory"; diff --git a/arch/arm/boot/dts/nspire-cx.dts b/arch/arm/boot/dts/nspire-cx.dts index 375b924f60d8..08e0b81b3385 100644 --- a/arch/arm/boot/dts/nspire-cx.dts +++ b/arch/arm/boot/dts/nspire-cx.dts @@ -69,6 +69,10 @@ 0x0709001d 0x070a0033 >; }; +&vbus_reg { + gpio = <&gpio 2 0>; +}; + / { model = "TI-NSPIRE CX"; compatible = "ti,nspire-cx"; diff --git a/arch/arm/boot/dts/nspire.dtsi b/arch/arm/boot/dts/nspire.dtsi index a22ffe633b49..390c91aea16d 100644 --- a/arch/arm/boot/dts/nspire.dtsi +++ b/arch/arm/boot/dts/nspire.dtsi @@ -54,6 +54,20 @@ clocks = <&ahb_clk>; }; + usb_phy: usb_phy { + compatible = "usb-nop-xceiv"; + }; + + vbus_reg: vbus_reg { + compatible = "regulator-fixed"; + + regulator-name = "USB VBUS output"; + regulator-type = "voltage"; + + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + ahb { compatible = "simple-bus"; #address-cells = <1>; @@ -65,8 +79,12 @@ }; usb0: usb@B0000000 { + compatible = "lsi,zevio-usb"; reg = <0xB0000000 0x1000>; interrupts = <8>; + + usb-phy = <&usb_phy>; + vbus-supply = <&vbus_reg>; }; usb1: usb@B4000000 { @@ -105,8 +123,11 @@ ranges; gpio: gpio@90000000 { + compatible = "lsi,zevio-gpio"; reg = <0x90000000 0x1000>; interrupts = <7>; + gpio-controller; + #gpio-cells = <2>; }; fast_timer: timer@90010000 { diff --git a/arch/arm/boot/dts/r8a73a4-ape6evm.dts b/arch/arm/boot/dts/r8a73a4-ape6evm.dts index 0d50bef01234..d1b6a07253ae 100644 --- a/arch/arm/boot/dts/r8a73a4-ape6evm.dts +++ b/arch/arm/boot/dts/r8a73a4-ape6evm.dts @@ -95,27 +95,27 @@ leds { compatible = "gpio-leds"; led1 { - gpios = <&pfc 28 GPIO_ACTIVE_LOW>; + gpios = <&pfc 28 GPIO_ACTIVE_HIGH>; label = "GNSS_EN"; }; led2 { - gpios = <&pfc 126 GPIO_ACTIVE_LOW>; + gpios = <&pfc 126 GPIO_ACTIVE_HIGH>; label = "NFC_NRST"; }; led3 { - gpios = <&pfc 132 GPIO_ACTIVE_LOW>; + gpios = <&pfc 132 GPIO_ACTIVE_HIGH>; label = "GNSS_NRST"; }; led4 { - gpios = <&pfc 232 GPIO_ACTIVE_LOW>; + gpios = <&pfc 232 GPIO_ACTIVE_HIGH>; label = "BT_WAKEUP"; }; led5 { - gpios = <&pfc 250 GPIO_ACTIVE_LOW>; + gpios = <&pfc 250 GPIO_ACTIVE_HIGH>; label = "STROBE"; }; led6 { - gpios = <&pfc 288 GPIO_ACTIVE_LOW>; + gpios = <&pfc 288 GPIO_ACTIVE_HIGH>; label = "BBRESETOUT"; }; }; @@ -123,10 +123,14 @@ keyboard { compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&keyboard_pins>; + zero-key { gpios = <&pfc 324 GPIO_ACTIVE_LOW>; linux,code = <KEY_0>; label = "S16"; + gpio-key,wakeup; }; menu-key { @@ -208,6 +212,12 @@ renesas,groups = "sdhi1_data4", "sdhi1_ctrl"; renesas,function = "sdhi1"; }; + + keyboard_pins: keyboard { + renesas,pins = "PORT324", "PORT325", "PORT326", "PORT327", + "PORT328", "PORT329"; + bias-pull-up; + }; }; &mmcif0 { diff --git a/arch/arm/boot/dts/r8a7740.dtsi b/arch/arm/boot/dts/r8a7740.dtsi index 8a092605d641..83c1c3ca1b8f 100644 --- a/arch/arm/boot/dts/r8a7740.dtsi +++ b/arch/arm/boot/dts/r8a7740.dtsi @@ -431,6 +431,18 @@ clock-frequency = <27000000>; clock-output-names = "dv"; }; + fmsick_clk: fmsick_clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <0>; + clock-output-names = "fmsick"; + }; + fmsock_clk: fmsock_clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <0>; + clock-output-names = "fmsock"; + }; fsiack_clk: fsiack_clk { compatible = "fixed-clock"; #clock-cells = <0>; @@ -459,13 +471,78 @@ }; /* Variable factor clocks (DIV6) */ + vclk1_clk: vclk1_clk@e6150008 { + compatible = "renesas,r8a7740-div6-clock", "renesas,cpg-div6-clock"; + reg = <0xe6150008 4>; + clocks = <&pllc1_div2_clk>, <0>, <&dv_clk>, + <&cpg_clocks R8A7740_CLK_USB24S>, + <&extal1_div2_clk>, <&extalr_clk>, <0>, + <0>; + #clock-cells = <0>; + clock-output-names = "vclk1"; + }; + vclk2_clk: vclk2_clk@e615000c { + compatible = "renesas,r8a7740-div6-clock", "renesas,cpg-div6-clock"; + reg = <0xe615000c 4>; + clocks = <&pllc1_div2_clk>, <0>, <&dv_clk>, + <&cpg_clocks R8A7740_CLK_USB24S>, + <&extal1_div2_clk>, <&extalr_clk>, <0>, + <0>; + #clock-cells = <0>; + clock-output-names = "vclk2"; + }; + fmsi_clk: fmsi_clk@e6150010 { + compatible = "renesas,r8a7740-div6-clock", "renesas,cpg-div6-clock"; + reg = <0xe6150010 4>; + clocks = <&pllc1_div2_clk>, <&fmsick_clk>, <0>, <0>; + #clock-cells = <0>; + clock-output-names = "fmsi"; + }; + fmso_clk: fmso_clk@e6150014 { + compatible = "renesas,r8a7740-div6-clock", "renesas,cpg-div6-clock"; + reg = <0xe6150014 4>; + clocks = <&pllc1_div2_clk>, <&fmsock_clk>, <0>, <0>; + #clock-cells = <0>; + clock-output-names = "fmso"; + }; + fsia_clk: fsia_clk@e6150018 { + compatible = "renesas,r8a7740-div6-clock", "renesas,cpg-div6-clock"; + reg = <0xe6150018 4>; + clocks = <&pllc1_div2_clk>, <&fsiack_clk>, <0>, <0>; + #clock-cells = <0>; + clock-output-names = "fsia"; + }; sub_clk: sub_clk@e6150080 { compatible = "renesas,r8a7740-div6-clock", "renesas,cpg-div6-clock"; reg = <0xe6150080 4>; - clocks = <&pllc1_div2_clk>; + clocks = <&pllc1_div2_clk>, + <&cpg_clocks R8A7740_CLK_USB24S>, <0>, <0>; #clock-cells = <0>; clock-output-names = "sub"; }; + spu_clk: spu_clk@e6150084 { + compatible = "renesas,r8a7740-div6-clock", "renesas,cpg-div6-clock"; + reg = <0xe6150084 4>; + clocks = <&pllc1_div2_clk>, + <&cpg_clocks R8A7740_CLK_USB24S>, <0>, <0>; + #clock-cells = <0>; + clock-output-names = "spu"; + }; + vou_clk: vou_clk@e6150088 { + compatible = "renesas,r8a7740-div6-clock", "renesas,cpg-div6-clock"; + reg = <0xe6150088 4>; + clocks = <&pllc1_div2_clk>, <&extal1_clk>, <&dv_clk>, + <0>; + #clock-cells = <0>; + clock-output-names = "vou"; + }; + stpro_clk: stpro_clk@e615009c { + compatible = "renesas,r8a7740-div6-clock", "renesas,cpg-div6-clock"; + reg = <0xe615009c 4>; + clocks = <&cpg_clocks R8A7740_CLK_PLLC0>; + #clock-cells = <0>; + clock-output-names = "stpro"; + }; /* Fixed factor clocks */ pllc1_div2_clk: pllc1_div2_clk { diff --git a/arch/arm/boot/dts/r8a7779-marzen.dts b/arch/arm/boot/dts/r8a7779-marzen.dts index e83d40e24bcd..540756cdf391 100644 --- a/arch/arm/boot/dts/r8a7779-marzen.dts +++ b/arch/arm/boot/dts/r8a7779-marzen.dts @@ -122,6 +122,12 @@ }; }; }; + + x3_clk: x3-clock { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <65000000>; + }; }; &du { @@ -129,6 +135,9 @@ pinctrl-names = "default"; status = "okay"; + clocks = <&mstp1_clks R8A7779_CLK_DU>, <&x3_clk>; + clock-names = "du", "dclkin.0"; + ports { port@0 { endpoint { diff --git a/arch/arm/boot/dts/r8a7790-lager.dts b/arch/arm/boot/dts/r8a7790-lager.dts index 0c3b6783b72a..329bb994aac0 100644 --- a/arch/arm/boot/dts/r8a7790-lager.dts +++ b/arch/arm/boot/dts/r8a7790-lager.dts @@ -222,6 +222,29 @@ }; }; }; + + hdmi-out { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_con: endpoint { + remote-endpoint = <&adv7511_out>; + }; + }; + }; + + x2_clk: x2-clock { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <148500000>; + }; + + x13_clk: x13-clock { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <148500000>; + }; }; &du { @@ -229,12 +252,26 @@ pinctrl-names = "default"; status = "okay"; + clocks = <&mstp7_clks R8A7790_CLK_DU0>, + <&mstp7_clks R8A7790_CLK_DU1>, + <&mstp7_clks R8A7790_CLK_DU2>, + <&mstp7_clks R8A7790_CLK_LVDS0>, + <&mstp7_clks R8A7790_CLK_LVDS1>, + <&x13_clk>, <&x2_clk>; + clock-names = "du.0", "du.1", "du.2", "lvds.0", "lvds.1", + "dclkin.0", "dclkin.1"; + ports { port@0 { endpoint { remote-endpoint = <&adv7123_in>; }; }; + port@1 { + endpoint { + remote-endpoint = <&adv7511_in>; + }; + }; port@2 { lvds_connector: endpoint { }; @@ -506,6 +543,38 @@ }; }; }; + + hdmi@39 { + compatible = "adi,adv7511w"; + reg = <0x39>; + interrupt-parent = <&gpio1>; + interrupts = <15 IRQ_TYPE_EDGE_FALLING>; + + adi,input-depth = <8>; + adi,input-colorspace = "rgb"; + adi,input-clock = "1x"; + adi,input-style = <1>; + adi,input-justification = "evenly"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + adv7511_in: endpoint { + remote-endpoint = <&du_out_lvds0>; + }; + }; + + port@1 { + reg = <1>; + adv7511_out: endpoint { + remote-endpoint = <&hdmi_con>; + }; + }; + }; + }; }; &iic3 { diff --git a/arch/arm/boot/dts/r8a7790.dtsi b/arch/arm/boot/dts/r8a7790.dtsi index 4b38fc920114..4bb2f4c17321 100644 --- a/arch/arm/boot/dts/r8a7790.dtsi +++ b/arch/arm/boot/dts/r8a7790.dtsi @@ -1,6 +1,7 @@ /* * Device Tree Source for the r8a7790 SoC * + * Copyright (C) 2015 Renesas Electronics Corporation * Copyright (C) 2013-2014 Renesas Solutions Corp. * Copyright (C) 2014 Cogent Embedded Inc. * @@ -369,13 +370,6 @@ dma-channels = <13>; }; - audmapp: dma-controller@ec740000 { - compatible = "renesas,rcar-audmapp"; - #dma-cells = <1>; - - reg = <0 0xec740000 0 0x200>; - }; - i2c0: i2c@e6508000 { #address-cells = <1>; #size-cells = <0>; @@ -493,17 +487,21 @@ sdhi0: sd@ee100000 { compatible = "renesas,sdhi-r8a7790"; - reg = <0 0xee100000 0 0x200>; + reg = <0 0xee100000 0 0x328>; interrupts = <0 165 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp3_clks R8A7790_CLK_SDHI0>; + dmas = <&dmac1 0xcd>, <&dmac1 0xce>; + dma-names = "tx", "rx"; status = "disabled"; }; sdhi1: sd@ee120000 { compatible = "renesas,sdhi-r8a7790"; - reg = <0 0xee120000 0 0x200>; + reg = <0 0xee120000 0 0x328>; interrupts = <0 166 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp3_clks R8A7790_CLK_SDHI1>; + dmas = <&dmac1 0xc9>, <&dmac1 0xca>; + dma-names = "tx", "rx"; status = "disabled"; }; @@ -512,6 +510,8 @@ reg = <0 0xee140000 0 0x100>; interrupts = <0 167 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp3_clks R8A7790_CLK_SDHI2>; + dmas = <&dmac1 0xc1>, <&dmac1 0xc2>; + dma-names = "tx", "rx"; status = "disabled"; }; @@ -520,6 +520,8 @@ reg = <0 0xee160000 0 0x100>; interrupts = <0 168 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp3_clks R8A7790_CLK_SDHI3>; + dmas = <&dmac1 0xd3>, <&dmac1 0xd4>; + dma-names = "tx", "rx"; status = "disabled"; }; @@ -792,6 +794,26 @@ }; }; + can0: can@e6e80000 { + compatible = "renesas,can-r8a7790"; + reg = <0 0xe6e80000 0 0x1000>; + interrupts = <0 186 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp9_clks R8A7790_CLK_RCAN0>, + <&cpg_clocks R8A7790_CLK_RCAN>, <&can_clk>; + clock-names = "clkp1", "clkp2", "can_clk"; + status = "disabled"; + }; + + can1: can@e6e88000 { + compatible = "renesas,can-r8a7790"; + reg = <0 0xe6e88000 0 0x1000>; + interrupts = <0 187 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp9_clks R8A7790_CLK_RCAN1>, + <&cpg_clocks R8A7790_CLK_RCAN>, <&can_clk>; + clock-names = "clkp1", "clkp2", "can_clk"; + status = "disabled"; + }; + clocks { #address-cells = <2>; #size-cells = <2>; @@ -838,16 +860,34 @@ clock-output-names = "audio_clk_c"; }; + /* External USB clock - can be overridden by the board */ + usb_extal_clk: usb_extal_clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <48000000>; + clock-output-names = "usb_extal"; + }; + + /* External CAN clock */ + can_clk: can_clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + /* This value must be overridden by the board. */ + clock-frequency = <0>; + clock-output-names = "can_clk"; + status = "disabled"; + }; + /* Special CPG clocks */ cpg_clocks: cpg_clocks@e6150000 { compatible = "renesas,r8a7790-cpg-clocks", "renesas,rcar-gen2-cpg-clocks"; reg = <0 0xe6150000 0 0x1000>; - clocks = <&extal_clk>; + clocks = <&extal_clk &usb_extal_clk>; #clock-cells = <1>; clock-output-names = "main", "pll0", "pll1", "pll3", "lb", "qspi", "sdh", "sd0", "sd1", - "z"; + "z", "rcan", "adsp"; }; /* Variable factor clocks */ @@ -1121,18 +1161,21 @@ mstp5_clks: mstp5_clks@e6150144 { compatible = "renesas,r8a7790-mstp-clocks", "renesas,cpg-mstp-clocks"; reg = <0 0xe6150144 0 4>, <0 0xe615003c 0 4>; - clocks = <&hp_clk>, <&hp_clk>, <&extal_clk>, <&p_clk>; + clocks = <&hp_clk>, <&hp_clk>, <&cpg_clocks R8A7790_CLK_ADSP>, + <&extal_clk>, <&p_clk>; #clock-cells = <1>; clock-indices = < R8A7790_CLK_AUDIO_DMAC0 R8A7790_CLK_AUDIO_DMAC1 - R8A7790_CLK_THERMAL R8A7790_CLK_PWM + R8A7790_CLK_ADSP_MOD R8A7790_CLK_THERMAL + R8A7790_CLK_PWM >; - clock-output-names = "audmac0", "audmac1", "thermal", "pwm"; + clock-output-names = "audmac0", "audmac1", "adsp_mod", + "thermal", "pwm"; }; mstp7_clks: mstp7_clks@e615014c { compatible = "renesas,r8a7790-mstp-clocks", "renesas,cpg-mstp-clocks"; reg = <0 0xe615014c 0 4>, <0 0xe61501c4 0 4>; - clocks = <&mp_clk>, <&mp_clk>, <&zs_clk>, <&zs_clk>, <&p_clk>, + clocks = <&mp_clk>, <&hp_clk>, <&zs_clk>, <&zs_clk>, <&p_clk>, <&p_clk>, <&zx_clk>, <&zx_clk>, <&zx_clk>, <&zx_clk>, <&zx_clk>; #clock-cells = <1>; @@ -1410,7 +1453,10 @@ reg = <0 0xec500000 0 0x1000>, /* SCU */ <0 0xec5a0000 0 0x100>, /* ADG */ <0 0xec540000 0 0x1000>, /* SSIU */ - <0 0xec541000 0 0x1280>; /* SSI */ + <0 0xec541000 0 0x1280>, /* SSI */ + <0 0xec740000 0 0x200>; /* Audio DMAC peri peri*/ + reg-names = "scu", "adg", "ssiu", "ssi", "audmapp"; + clocks = <&mstp10_clks R8A7790_CLK_SSI_ALL>, <&mstp10_clks R8A7790_CLK_SSI9>, <&mstp10_clks R8A7790_CLK_SSI8>, <&mstp10_clks R8A7790_CLK_SSI7>, <&mstp10_clks R8A7790_CLK_SSI6>, @@ -1435,34 +1481,171 @@ status = "disabled"; rcar_sound,dvc { - dvc0: dvc@0 { }; - dvc1: dvc@1 { }; + dvc0: dvc@0 { + dmas = <&audma0 0xbc>; + dma-names = "tx"; + }; + dvc1: dvc@1 { + dmas = <&audma0 0xbe>; + dma-names = "tx"; + }; }; rcar_sound,src { - src0: src@0 { interrupts = <0 352 IRQ_TYPE_LEVEL_HIGH>; }; - src1: src@1 { interrupts = <0 353 IRQ_TYPE_LEVEL_HIGH>; }; - src2: src@2 { interrupts = <0 354 IRQ_TYPE_LEVEL_HIGH>; }; - src3: src@3 { interrupts = <0 355 IRQ_TYPE_LEVEL_HIGH>; }; - src4: src@4 { interrupts = <0 356 IRQ_TYPE_LEVEL_HIGH>; }; - src5: src@5 { interrupts = <0 357 IRQ_TYPE_LEVEL_HIGH>; }; - src6: src@6 { interrupts = <0 358 IRQ_TYPE_LEVEL_HIGH>; }; - src7: src@7 { interrupts = <0 359 IRQ_TYPE_LEVEL_HIGH>; }; - src8: src@8 { interrupts = <0 360 IRQ_TYPE_LEVEL_HIGH>; }; - src9: src@9 { interrupts = <0 361 IRQ_TYPE_LEVEL_HIGH>; }; + src0: src@0 { + interrupts = <0 352 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x85>, <&audma1 0x9a>; + dma-names = "rx", "tx"; + }; + src1: src@1 { + interrupts = <0 353 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x87>, <&audma1 0x9c>; + dma-names = "rx", "tx"; + }; + src2: src@2 { + interrupts = <0 354 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x89>, <&audma1 0x9e>; + dma-names = "rx", "tx"; + }; + src3: src@3 { + interrupts = <0 355 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x8b>, <&audma1 0xa0>; + dma-names = "rx", "tx"; + }; + src4: src@4 { + interrupts = <0 356 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x8d>, <&audma1 0xb0>; + dma-names = "rx", "tx"; + }; + src5: src@5 { + interrupts = <0 357 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x8f>, <&audma1 0xb2>; + dma-names = "rx", "tx"; + }; + src6: src@6 { + interrupts = <0 358 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x91>, <&audma1 0xb4>; + dma-names = "rx", "tx"; + }; + src7: src@7 { + interrupts = <0 359 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x93>, <&audma1 0xb6>; + dma-names = "rx", "tx"; + }; + src8: src@8 { + interrupts = <0 360 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x95>, <&audma1 0xb8>; + dma-names = "rx", "tx"; + }; + src9: src@9 { + interrupts = <0 361 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x97>, <&audma1 0xba>; + dma-names = "rx", "tx"; + }; }; rcar_sound,ssi { - ssi0: ssi@0 { interrupts = <0 370 IRQ_TYPE_LEVEL_HIGH>; }; - ssi1: ssi@1 { interrupts = <0 371 IRQ_TYPE_LEVEL_HIGH>; }; - ssi2: ssi@2 { interrupts = <0 372 IRQ_TYPE_LEVEL_HIGH>; }; - ssi3: ssi@3 { interrupts = <0 373 IRQ_TYPE_LEVEL_HIGH>; }; - ssi4: ssi@4 { interrupts = <0 374 IRQ_TYPE_LEVEL_HIGH>; }; - ssi5: ssi@5 { interrupts = <0 375 IRQ_TYPE_LEVEL_HIGH>; }; - ssi6: ssi@6 { interrupts = <0 376 IRQ_TYPE_LEVEL_HIGH>; }; - ssi7: ssi@7 { interrupts = <0 377 IRQ_TYPE_LEVEL_HIGH>; }; - ssi8: ssi@8 { interrupts = <0 378 IRQ_TYPE_LEVEL_HIGH>; }; - ssi9: ssi@9 { interrupts = <0 379 IRQ_TYPE_LEVEL_HIGH>; }; + ssi0: ssi@0 { + interrupts = <0 370 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x01>, <&audma1 0x02>, <&audma0 0x15>, <&audma1 0x16>; + dma-names = "rx", "tx", "rxu", "txu"; + }; + ssi1: ssi@1 { + interrupts = <0 371 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x03>, <&audma1 0x04>, <&audma0 0x49>, <&audma1 0x4a>; + dma-names = "rx", "tx", "rxu", "txu"; + }; + ssi2: ssi@2 { + interrupts = <0 372 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x05>, <&audma1 0x06>, <&audma0 0x63>, <&audma1 0x64>; + dma-names = "rx", "tx", "rxu", "txu"; + }; + ssi3: ssi@3 { + interrupts = <0 373 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x07>, <&audma1 0x08>, <&audma0 0x6f>, <&audma1 0x70>; + dma-names = "rx", "tx", "rxu", "txu"; + }; + ssi4: ssi@4 { + interrupts = <0 374 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x09>, <&audma1 0x0a>, <&audma0 0x71>, <&audma1 0x72>; + dma-names = "rx", "tx", "rxu", "txu"; + }; + ssi5: ssi@5 { + interrupts = <0 375 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x0b>, <&audma1 0x0c>, <&audma0 0x73>, <&audma1 0x74>; + dma-names = "rx", "tx", "rxu", "txu"; + }; + ssi6: ssi@6 { + interrupts = <0 376 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x0d>, <&audma1 0x0e>, <&audma0 0x75>, <&audma1 0x76>; + dma-names = "rx", "tx", "rxu", "txu"; + }; + ssi7: ssi@7 { + interrupts = <0 377 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x0f>, <&audma1 0x10>, <&audma0 0x79>, <&audma1 0x7a>; + dma-names = "rx", "tx", "rxu", "txu"; + }; + ssi8: ssi@8 { + interrupts = <0 378 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x11>, <&audma1 0x12>, <&audma0 0x7b>, <&audma1 0x7c>; + dma-names = "rx", "tx", "rxu", "txu"; + }; + ssi9: ssi@9 { + interrupts = <0 379 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x13>, <&audma1 0x14>, <&audma0 0x7d>, <&audma1 0x7e>; + dma-names = "rx", "tx", "rxu", "txu"; + }; }; }; + + ipmmu_sy0: mmu@e6280000 { + compatible = "renesas,ipmmu-vmsa"; + reg = <0 0xe6280000 0 0x1000>; + interrupts = <0 223 IRQ_TYPE_LEVEL_HIGH>, + <0 224 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + status = "disabled"; + }; + + ipmmu_sy1: mmu@e6290000 { + compatible = "renesas,ipmmu-vmsa"; + reg = <0 0xe6290000 0 0x1000>; + interrupts = <0 225 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + status = "disabled"; + }; + + ipmmu_ds: mmu@e6740000 { + compatible = "renesas,ipmmu-vmsa"; + reg = <0 0xe6740000 0 0x1000>; + interrupts = <0 198 IRQ_TYPE_LEVEL_HIGH>, + <0 199 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + status = "disabled"; + }; + + ipmmu_mp: mmu@ec680000 { + compatible = "renesas,ipmmu-vmsa"; + reg = <0 0xec680000 0 0x1000>; + interrupts = <0 226 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + status = "disabled"; + }; + + ipmmu_mx: mmu@fe951000 { + compatible = "renesas,ipmmu-vmsa"; + reg = <0 0xfe951000 0 0x1000>; + interrupts = <0 222 IRQ_TYPE_LEVEL_HIGH>, + <0 221 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + status = "disabled"; + }; + + ipmmu_rt: mmu@ffc80000 { + compatible = "renesas,ipmmu-vmsa"; + reg = <0 0xffc80000 0 0x1000>; + interrupts = <0 307 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + status = "disabled"; + }; }; diff --git a/arch/arm/boot/dts/r8a7791-henninger.dts b/arch/arm/boot/dts/r8a7791-henninger.dts index d2ebf11f9881..e33e4047b0b0 100644 --- a/arch/arm/boot/dts/r8a7791-henninger.dts +++ b/arch/arm/boot/dts/r8a7791-henninger.dts @@ -141,6 +141,11 @@ renesas,groups = "vin0_data8", "vin0_clk"; renesas,function = "vin0"; }; + + can0_pins: can0 { + renesas,groups = "can0_data"; + renesas,function = "can0"; + }; }; &scif0 { @@ -307,3 +312,9 @@ }; }; }; + +&can0 { + pinctrl-0 = <&can0_pins>; + pinctrl-names = "default"; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/r8a7791-koelsch.dts b/arch/arm/boot/dts/r8a7791-koelsch.dts index a3c27807f6c5..75fa9852e235 100644 --- a/arch/arm/boot/dts/r8a7791-koelsch.dts +++ b/arch/arm/boot/dts/r8a7791-koelsch.dts @@ -258,6 +258,29 @@ system-clock-frequency = <11289600>; }; }; + + hdmi-out { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_con: endpoint { + remote-endpoint = <&adv7511_out>; + }; + }; + }; + + x2_clk: x2-clock { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <148500000>; + }; + + x13_clk: x13-clock { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <148500000>; + }; }; &du { @@ -265,7 +288,19 @@ pinctrl-names = "default"; status = "okay"; + clocks = <&mstp7_clks R8A7791_CLK_DU0>, + <&mstp7_clks R8A7791_CLK_DU1>, + <&mstp7_clks R8A7791_CLK_LVDS0>, + <&x13_clk>, <&x2_clk>; + clock-names = "du.0", "du.1", "lvds.0", + "dclkin.0", "dclkin.1"; + ports { + port@0 { + endpoint { + remote-endpoint = <&adv7511_in>; + }; + }; port@1 { lvds_connector: endpoint { }; @@ -284,7 +319,7 @@ }; du_pins: du { - renesas,groups = "du_rgb666", "du_sync", "du_clk_out_0"; + renesas,groups = "du_rgb666", "du_sync", "du_disp", "du_clk_out_0"; renesas,function = "du"; }; @@ -506,6 +541,38 @@ }; }; + hdmi@39 { + compatible = "adi,adv7511w"; + reg = <0x39>; + interrupt-parent = <&gpio3>; + interrupts = <29 IRQ_TYPE_EDGE_FALLING>; + + adi,input-depth = <8>; + adi,input-colorspace = "rgb"; + adi,input-clock = "1x"; + adi,input-style = <1>; + adi,input-justification = "evenly"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + adv7511_in: endpoint { + remote-endpoint = <&du_out_rgb>; + }; + }; + + port@1 { + reg = <1>; + adv7511_out: endpoint { + remote-endpoint = <&hdmi_con>; + }; + }; + }; + }; + eeprom@50 { compatible = "renesas,24c02"; reg = <0x50>; diff --git a/arch/arm/boot/dts/r8a7791.dtsi b/arch/arm/boot/dts/r8a7791.dtsi index e35812a0d8d4..4696062f6dde 100644 --- a/arch/arm/boot/dts/r8a7791.dtsi +++ b/arch/arm/boot/dts/r8a7791.dtsi @@ -1,7 +1,7 @@ /* * Device Tree Source for the r8a7791 SoC * - * Copyright (C) 2013-2014 Renesas Electronics Corporation + * Copyright (C) 2013-2015 Renesas Electronics Corporation * Copyright (C) 2013-2014 Renesas Solutions Corp. * Copyright (C) 2014 Cogent Embedded Inc. * @@ -357,13 +357,6 @@ dma-channels = <13>; }; - audmapp: dma-controller@ec740000 { - compatible = "renesas,rcar-audmapp"; - #dma-cells = <1>; - - reg = <0 0xec740000 0 0x200>; - }; - /* The memory map in the User's Manual maps the cores to bus numbers */ i2c0: i2c@e6508000 { #address-cells = <1>; @@ -482,9 +475,11 @@ sdhi0: sd@ee100000 { compatible = "renesas,sdhi-r8a7791"; - reg = <0 0xee100000 0 0x200>; + reg = <0 0xee100000 0 0x328>; interrupts = <0 165 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp3_clks R8A7791_CLK_SDHI0>; + dmas = <&dmac1 0xcd>, <&dmac1 0xce>; + dma-names = "tx", "rx"; status = "disabled"; }; @@ -493,6 +488,8 @@ reg = <0 0xee140000 0 0x100>; interrupts = <0 167 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp3_clks R8A7791_CLK_SDHI1>; + dmas = <&dmac1 0xc1>, <&dmac1 0xc2>; + dma-names = "tx", "rx"; status = "disabled"; }; @@ -501,6 +498,8 @@ reg = <0 0xee160000 0 0x100>; interrupts = <0 168 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp3_clks R8A7791_CLK_SDHI2>; + dmas = <&dmac1 0xd3>, <&dmac1 0xd4>; + dma-names = "tx", "rx"; status = "disabled"; }; @@ -816,6 +815,26 @@ }; }; + can0: can@e6e80000 { + compatible = "renesas,can-r8a7791"; + reg = <0 0xe6e80000 0 0x1000>; + interrupts = <0 186 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp9_clks R8A7791_CLK_RCAN0>, + <&cpg_clocks R8A7791_CLK_RCAN>, <&can_clk>; + clock-names = "clkp1", "clkp2", "can_clk"; + status = "disabled"; + }; + + can1: can@e6e88000 { + compatible = "renesas,can-r8a7791"; + reg = <0 0xe6e88000 0 0x1000>; + interrupts = <0 187 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp9_clks R8A7791_CLK_RCAN1>, + <&cpg_clocks R8A7791_CLK_RCAN>, <&can_clk>; + clock-names = "clkp1", "clkp2", "can_clk"; + status = "disabled"; + }; + clocks { #address-cells = <2>; #size-cells = <2>; @@ -862,31 +881,50 @@ status = "disabled"; }; + /* External USB clock - can be overridden by the board */ + usb_extal_clk: usb_extal_clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <48000000>; + clock-output-names = "usb_extal"; + }; + + /* External CAN clock */ + can_clk: can_clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + /* This value must be overridden by the board. */ + clock-frequency = <0>; + clock-output-names = "can_clk"; + status = "disabled"; + }; + /* Special CPG clocks */ cpg_clocks: cpg_clocks@e6150000 { compatible = "renesas,r8a7791-cpg-clocks", "renesas,rcar-gen2-cpg-clocks"; reg = <0 0xe6150000 0 0x1000>; - clocks = <&extal_clk>; + clocks = <&extal_clk &usb_extal_clk>; #clock-cells = <1>; clock-output-names = "main", "pll0", "pll1", "pll3", - "lb", "qspi", "sdh", "sd0", "z"; + "lb", "qspi", "sdh", "sd0", "z", + "rcan", "adsp"; }; /* Variable factor clocks */ - sd1_clk: sd2_clk@e6150078 { + sd2_clk: sd2_clk@e6150078 { compatible = "renesas,r8a7791-div6-clock", "renesas,cpg-div6-clock"; reg = <0 0xe6150078 0 4>; clocks = <&pll1_div2_clk>; #clock-cells = <0>; - clock-output-names = "sd1"; + clock-output-names = "sd2"; }; - sd2_clk: sd3_clk@e615026c { + sd3_clk: sd3_clk@e615026c { compatible = "renesas,r8a7791-div6-clock", "renesas,cpg-div6-clock"; reg = <0 0xe615026c 0 4>; clocks = <&pll1_div2_clk>; #clock-cells = <0>; - clock-output-names = "sd2"; + clock-output-names = "sd3"; }; mmc0_clk: mmc0_clk@e6150240 { compatible = "renesas,r8a7791-div6-clock", "renesas,cpg-div6-clock"; @@ -1107,7 +1145,7 @@ mstp3_clks: mstp3_clks@e615013c { compatible = "renesas,r8a7791-mstp-clocks", "renesas,cpg-mstp-clocks"; reg = <0 0xe615013c 0 4>, <0 0xe6150048 0 4>; - clocks = <&cp_clk>, <&sd2_clk>, <&sd1_clk>, <&cpg_clocks R8A7791_CLK_SD0>, + clocks = <&cp_clk>, <&sd3_clk>, <&sd2_clk>, <&cpg_clocks R8A7791_CLK_SD0>, <&mmc0_clk>, <&hp_clk>, <&mp_clk>, <&hp_clk>, <&mp_clk>, <&rclk_clk>, <&hp_clk>, <&hp_clk>; #clock-cells = <1>; @@ -1125,18 +1163,21 @@ mstp5_clks: mstp5_clks@e6150144 { compatible = "renesas,r8a7791-mstp-clocks", "renesas,cpg-mstp-clocks"; reg = <0 0xe6150144 0 4>, <0 0xe615003c 0 4>; - clocks = <&hp_clk>, <&hp_clk>, <&extal_clk>, <&p_clk>; + clocks = <&hp_clk>, <&hp_clk>, <&cpg_clocks R8A7791_CLK_ADSP>, + <&extal_clk>, <&p_clk>; #clock-cells = <1>; clock-indices = < R8A7791_CLK_AUDIO_DMAC0 R8A7791_CLK_AUDIO_DMAC1 - R8A7791_CLK_THERMAL R8A7791_CLK_PWM + R8A7791_CLK_ADSP_MOD R8A7791_CLK_THERMAL + R8A7791_CLK_PWM >; - clock-output-names = "audmac0", "audmac1", "thermal", "pwm"; + clock-output-names = "audmac0", "audmac1", "adsp_mod", + "thermal", "pwm"; }; mstp7_clks: mstp7_clks@e615014c { compatible = "renesas,r8a7791-mstp-clocks", "renesas,cpg-mstp-clocks"; reg = <0 0xe615014c 0 4>, <0 0xe61501c4 0 4>; - clocks = <&mp_clk>, <&mp_clk>, <&zs_clk>, <&p_clk>, <&p_clk>, <&zs_clk>, + clocks = <&mp_clk>, <&hp_clk>, <&zs_clk>, <&p_clk>, <&p_clk>, <&zs_clk>, <&zs_clk>, <&p_clk>, <&p_clk>, <&p_clk>, <&p_clk>, <&zx_clk>, <&zx_clk>, <&zx_clk>; #clock-cells = <1>; @@ -1154,7 +1195,7 @@ mstp8_clks: mstp8_clks@e6150990 { compatible = "renesas,r8a7791-mstp-clocks", "renesas,cpg-mstp-clocks"; reg = <0 0xe6150990 0 4>, <0 0xe61509a0 0 4>; - clocks = <&zg_clk>, <&hp_clk>, <&zg_clk>, <&zg_clk>, + clocks = <&zx_clk>, <&hp_clk>, <&zg_clk>, <&zg_clk>, <&zg_clk>, <&p_clk>, <&zs_clk>, <&zs_clk>; #clock-cells = <1>; clock-indices = < @@ -1384,6 +1425,66 @@ status = "disabled"; }; + ipmmu_sy0: mmu@e6280000 { + compatible = "renesas,ipmmu-vmsa"; + reg = <0 0xe6280000 0 0x1000>; + interrupts = <0 223 IRQ_TYPE_LEVEL_HIGH>, + <0 224 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + status = "disabled"; + }; + + ipmmu_sy1: mmu@e6290000 { + compatible = "renesas,ipmmu-vmsa"; + reg = <0 0xe6290000 0 0x1000>; + interrupts = <0 225 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + status = "disabled"; + }; + + ipmmu_ds: mmu@e6740000 { + compatible = "renesas,ipmmu-vmsa"; + reg = <0 0xe6740000 0 0x1000>; + interrupts = <0 198 IRQ_TYPE_LEVEL_HIGH>, + <0 199 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + status = "disabled"; + }; + + ipmmu_mp: mmu@ec680000 { + compatible = "renesas,ipmmu-vmsa"; + reg = <0 0xec680000 0 0x1000>; + interrupts = <0 226 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + status = "disabled"; + }; + + ipmmu_mx: mmu@fe951000 { + compatible = "renesas,ipmmu-vmsa"; + reg = <0 0xfe951000 0 0x1000>; + interrupts = <0 222 IRQ_TYPE_LEVEL_HIGH>, + <0 221 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + status = "disabled"; + }; + + ipmmu_rt: mmu@ffc80000 { + compatible = "renesas,ipmmu-vmsa"; + reg = <0 0xffc80000 0 0x1000>; + interrupts = <0 307 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + status = "disabled"; + }; + + ipmmu_gp: mmu@e62a0000 { + compatible = "renesas,ipmmu-vmsa"; + reg = <0 0xe62a0000 0 0x1000>; + interrupts = <0 260 IRQ_TYPE_LEVEL_HIGH>, + <0 261 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + status = "disabled"; + }; + rcar_sound: rcar_sound@ec500000 { /* * #sound-dai-cells is required @@ -1395,7 +1496,10 @@ reg = <0 0xec500000 0 0x1000>, /* SCU */ <0 0xec5a0000 0 0x100>, /* ADG */ <0 0xec540000 0 0x1000>, /* SSIU */ - <0 0xec541000 0 0x1280>; /* SSI */ + <0 0xec541000 0 0x1280>, /* SSI */ + <0 0xec740000 0 0x200>; /* Audio DMAC peri peri*/ + reg-names = "scu", "adg", "ssiu", "ssi", "audmapp"; + clocks = <&mstp10_clks R8A7791_CLK_SSI_ALL>, <&mstp10_clks R8A7791_CLK_SSI9>, <&mstp10_clks R8A7791_CLK_SSI8>, <&mstp10_clks R8A7791_CLK_SSI7>, <&mstp10_clks R8A7791_CLK_SSI6>, @@ -1420,34 +1524,120 @@ status = "disabled"; rcar_sound,dvc { - dvc0: dvc@0 { }; - dvc1: dvc@1 { }; + dvc0: dvc@0 { + dmas = <&audma0 0xbc>; + dma-names = "tx"; + }; + dvc1: dvc@1 { + dmas = <&audma0 0xbe>; + dma-names = "tx"; + }; }; rcar_sound,src { - src0: src@0 { interrupts = <0 352 IRQ_TYPE_LEVEL_HIGH>; }; - src1: src@1 { interrupts = <0 353 IRQ_TYPE_LEVEL_HIGH>; }; - src2: src@2 { interrupts = <0 354 IRQ_TYPE_LEVEL_HIGH>; }; - src3: src@3 { interrupts = <0 355 IRQ_TYPE_LEVEL_HIGH>; }; - src4: src@4 { interrupts = <0 356 IRQ_TYPE_LEVEL_HIGH>; }; - src5: src@5 { interrupts = <0 357 IRQ_TYPE_LEVEL_HIGH>; }; - src6: src@6 { interrupts = <0 358 IRQ_TYPE_LEVEL_HIGH>; }; - src7: src@7 { interrupts = <0 359 IRQ_TYPE_LEVEL_HIGH>; }; - src8: src@8 { interrupts = <0 360 IRQ_TYPE_LEVEL_HIGH>; }; - src9: src@9 { interrupts = <0 361 IRQ_TYPE_LEVEL_HIGH>; }; + src0: src@0 { + interrupts = <0 352 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x85>, <&audma1 0x9a>; + dma-names = "rx", "tx"; + }; + src1: src@1 { + interrupts = <0 353 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x87>, <&audma1 0x9c>; + dma-names = "rx", "tx"; + }; + src2: src@2 { + interrupts = <0 354 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x89>, <&audma1 0x9e>; + dma-names = "rx", "tx"; + }; + src3: src@3 { + interrupts = <0 355 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x8b>, <&audma1 0xa0>; + dma-names = "rx", "tx"; + }; + src4: src@4 { + interrupts = <0 356 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x8d>, <&audma1 0xb0>; + dma-names = "rx", "tx"; + }; + src5: src@5 { + interrupts = <0 357 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x8f>, <&audma1 0xb2>; + dma-names = "rx", "tx"; + }; + src6: src@6 { + interrupts = <0 358 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x91>, <&audma1 0xb4>; + dma-names = "rx", "tx"; + }; + src7: src@7 { + interrupts = <0 359 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x93>, <&audma1 0xb6>; + dma-names = "rx", "tx"; + }; + src8: src@8 { + interrupts = <0 360 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x95>, <&audma1 0xb8>; + dma-names = "rx", "tx"; + }; + src9: src@9 { + interrupts = <0 361 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x97>, <&audma1 0xba>; + dma-names = "rx", "tx"; + }; }; rcar_sound,ssi { - ssi0: ssi@0 { interrupts = <0 370 IRQ_TYPE_LEVEL_HIGH>; }; - ssi1: ssi@1 { interrupts = <0 371 IRQ_TYPE_LEVEL_HIGH>; }; - ssi2: ssi@2 { interrupts = <0 372 IRQ_TYPE_LEVEL_HIGH>; }; - ssi3: ssi@3 { interrupts = <0 373 IRQ_TYPE_LEVEL_HIGH>; }; - ssi4: ssi@4 { interrupts = <0 374 IRQ_TYPE_LEVEL_HIGH>; }; - ssi5: ssi@5 { interrupts = <0 375 IRQ_TYPE_LEVEL_HIGH>; }; - ssi6: ssi@6 { interrupts = <0 376 IRQ_TYPE_LEVEL_HIGH>; }; - ssi7: ssi@7 { interrupts = <0 377 IRQ_TYPE_LEVEL_HIGH>; }; - ssi8: ssi@8 { interrupts = <0 378 IRQ_TYPE_LEVEL_HIGH>; }; - ssi9: ssi@9 { interrupts = <0 379 IRQ_TYPE_LEVEL_HIGH>; }; + ssi0: ssi@0 { + interrupts = <0 370 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x01>, <&audma1 0x02>, <&audma0 0x15>, <&audma1 0x16>; + dma-names = "rx", "tx", "rxu", "txu"; + }; + ssi1: ssi@1 { + interrupts = <0 371 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x03>, <&audma1 0x04>, <&audma0 0x49>, <&audma1 0x4a>; + dma-names = "rx", "tx", "rxu", "txu"; + }; + ssi2: ssi@2 { + interrupts = <0 372 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x05>, <&audma1 0x06>, <&audma0 0x63>, <&audma1 0x64>; + dma-names = "rx", "tx", "rxu", "txu"; + }; + ssi3: ssi@3 { + interrupts = <0 373 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x07>, <&audma1 0x08>, <&audma0 0x6f>, <&audma1 0x70>; + dma-names = "rx", "tx", "rxu", "txu"; + }; + ssi4: ssi@4 { + interrupts = <0 374 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x09>, <&audma1 0x0a>, <&audma0 0x71>, <&audma1 0x72>; + dma-names = "rx", "tx", "rxu", "txu"; + }; + ssi5: ssi@5 { + interrupts = <0 375 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x0b>, <&audma1 0x0c>, <&audma0 0x73>, <&audma1 0x74>; + dma-names = "rx", "tx", "rxu", "txu"; + }; + ssi6: ssi@6 { + interrupts = <0 376 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x0d>, <&audma1 0x0e>, <&audma0 0x75>, <&audma1 0x76>; + dma-names = "rx", "tx", "rxu", "txu"; + }; + ssi7: ssi@7 { + interrupts = <0 377 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x0f>, <&audma1 0x10>, <&audma0 0x79>, <&audma1 0x7a>; + dma-names = "rx", "tx", "rxu", "txu"; + }; + ssi8: ssi@8 { + interrupts = <0 378 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x11>, <&audma1 0x12>, <&audma0 0x7b>, <&audma1 0x7c>; + dma-names = "rx", "tx", "rxu", "txu"; + }; + ssi9: ssi@9 { + interrupts = <0 379 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&audma0 0x13>, <&audma1 0x14>, <&audma0 0x7d>, <&audma1 0x7e>; + dma-names = "rx", "tx", "rxu", "txu"; + }; }; }; }; diff --git a/arch/arm/boot/dts/r8a7794-alt.dts b/arch/arm/boot/dts/r8a7794-alt.dts index 0d848e605071..928cfa641475 100644 --- a/arch/arm/boot/dts/r8a7794-alt.dts +++ b/arch/arm/boot/dts/r8a7794-alt.dts @@ -43,6 +43,19 @@ status = "okay"; }; +ðer { + phy-handle = <&phy1>; + renesas,ether-link-active-low; + status = "okay"; + + phy1: ethernet-phy@1 { + reg = <1>; + interrupt-parent = <&irqc0>; + interrupts = <8 IRQ_TYPE_LEVEL_LOW>; + micrel,led-mode = <1>; + }; +}; + &scif2 { status = "okay"; }; diff --git a/arch/arm/boot/dts/r8a7794.dtsi b/arch/arm/boot/dts/r8a7794.dtsi index 8f78da5ef10b..7a3ffa51a8bf 100644 --- a/arch/arm/boot/dts/r8a7794.dtsi +++ b/arch/arm/boot/dts/r8a7794.dtsi @@ -107,6 +107,66 @@ <0 17 IRQ_TYPE_LEVEL_HIGH>; }; + dmac0: dma-controller@e6700000 { + compatible = "renesas,rcar-dmac"; + reg = <0 0xe6700000 0 0x20000>; + interrupts = <0 197 IRQ_TYPE_LEVEL_HIGH + 0 200 IRQ_TYPE_LEVEL_HIGH + 0 201 IRQ_TYPE_LEVEL_HIGH + 0 202 IRQ_TYPE_LEVEL_HIGH + 0 203 IRQ_TYPE_LEVEL_HIGH + 0 204 IRQ_TYPE_LEVEL_HIGH + 0 205 IRQ_TYPE_LEVEL_HIGH + 0 206 IRQ_TYPE_LEVEL_HIGH + 0 207 IRQ_TYPE_LEVEL_HIGH + 0 208 IRQ_TYPE_LEVEL_HIGH + 0 209 IRQ_TYPE_LEVEL_HIGH + 0 210 IRQ_TYPE_LEVEL_HIGH + 0 211 IRQ_TYPE_LEVEL_HIGH + 0 212 IRQ_TYPE_LEVEL_HIGH + 0 213 IRQ_TYPE_LEVEL_HIGH + 0 214 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "error", + "ch0", "ch1", "ch2", "ch3", + "ch4", "ch5", "ch6", "ch7", + "ch8", "ch9", "ch10", "ch11", + "ch12", "ch13", "ch14"; + clocks = <&mstp2_clks R8A7794_CLK_SYS_DMAC0>; + clock-names = "fck"; + #dma-cells = <1>; + dma-channels = <15>; + }; + + dmac1: dma-controller@e6720000 { + compatible = "renesas,rcar-dmac"; + reg = <0 0xe6720000 0 0x20000>; + interrupts = <0 220 IRQ_TYPE_LEVEL_HIGH + 0 216 IRQ_TYPE_LEVEL_HIGH + 0 217 IRQ_TYPE_LEVEL_HIGH + 0 218 IRQ_TYPE_LEVEL_HIGH + 0 219 IRQ_TYPE_LEVEL_HIGH + 0 308 IRQ_TYPE_LEVEL_HIGH + 0 309 IRQ_TYPE_LEVEL_HIGH + 0 310 IRQ_TYPE_LEVEL_HIGH + 0 311 IRQ_TYPE_LEVEL_HIGH + 0 312 IRQ_TYPE_LEVEL_HIGH + 0 313 IRQ_TYPE_LEVEL_HIGH + 0 314 IRQ_TYPE_LEVEL_HIGH + 0 315 IRQ_TYPE_LEVEL_HIGH + 0 316 IRQ_TYPE_LEVEL_HIGH + 0 317 IRQ_TYPE_LEVEL_HIGH + 0 318 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "error", + "ch0", "ch1", "ch2", "ch3", + "ch4", "ch5", "ch6", "ch7", + "ch8", "ch9", "ch10", "ch11", + "ch12", "ch13", "ch14"; + clocks = <&mstp2_clks R8A7794_CLK_SYS_DMAC1>; + clock-names = "fck"; + #dma-cells = <1>; + dma-channels = <15>; + }; + scifa0: serial@e6c40000 { compatible = "renesas,scifa-r8a7794", "renesas,scifa"; reg = <0 0xe6c40000 0 64>; @@ -269,6 +329,41 @@ status = "disabled"; }; + ether: ethernet@ee700000 { + compatible = "renesas,ether-r8a7794"; + reg = <0 0xee700000 0 0x400>; + interrupts = <0 162 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp8_clks R8A7794_CLK_ETHER>; + phy-mode = "rmii"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + sdhi0: sd@ee100000 { + compatible = "renesas,sdhi-r8a7794"; + reg = <0 0xee100000 0 0x200>; + interrupts = <0 165 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp3_clks R8A7794_CLK_SDHI0>; + status = "disabled"; + }; + + sdhi1: sd@ee140000 { + compatible = "renesas,sdhi-r8a7794"; + reg = <0 0xee140000 0 0x100>; + interrupts = <0 167 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp3_clks R8A7794_CLK_SDHI1>; + status = "disabled"; + }; + + sdhi2: sd@ee160000 { + compatible = "renesas,sdhi-r8a7794"; + reg = <0 0xee160000 0 0x100>; + interrupts = <0 168 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp3_clks R8A7794_CLK_SDHI2>; + status = "disabled"; + }; + clocks { #address-cells = <2>; #size-cells = <2>; @@ -294,19 +389,19 @@ "lb", "qspi", "sdh", "sd0", "z"; }; /* Variable factor clocks */ - sd1_clk: sd2_clk@e6150078 { + sd2_clk: sd2_clk@e6150078 { compatible = "renesas,r8a7794-div6-clock", "renesas,cpg-div6-clock"; reg = <0 0xe6150078 0 4>; clocks = <&pll1_div2_clk>; #clock-cells = <0>; - clock-output-names = "sd1"; + clock-output-names = "sd2"; }; - sd2_clk: sd3_clk@e615007c { + sd3_clk: sd3_clk@e615026c { compatible = "renesas,r8a7794-div6-clock", "renesas,cpg-div6-clock"; - reg = <0 0xe615007c 0 4>; + reg = <0 0xe615026c 0 4>; clocks = <&pll1_div2_clk>; #clock-cells = <0>; - clock-output-names = "sd2"; + clock-output-names = "sd3"; }; mmc0_clk: mmc0_clk@e6150240 { compatible = "renesas,r8a7794-div6-clock", "renesas,cpg-div6-clock"; @@ -518,7 +613,7 @@ mstp3_clks: mstp3_clks@e615013c { compatible = "renesas,r8a7794-mstp-clocks", "renesas,cpg-mstp-clocks"; reg = <0 0xe615013c 0 4>, <0 0xe6150048 0 4>; - clocks = <&sd2_clk>, <&sd1_clk>, <&cpg_clocks R8A7794_CLK_SD0>, + clocks = <&sd3_clk>, <&sd2_clk>, <&cpg_clocks R8A7794_CLK_SD0>, <&mmc0_clk>, <&rclk_clk>, <&hp_clk>, <&hp_clk>; #clock-cells = <1>; clock-indices = < @@ -585,4 +680,54 @@ clock-output-names = "scifa3", "scifa4", "scifa5"; }; }; + + ipmmu_sy0: mmu@e6280000 { + compatible = "renesas,ipmmu-vmsa"; + reg = <0 0xe6280000 0 0x1000>; + interrupts = <0 223 IRQ_TYPE_LEVEL_HIGH>, + <0 224 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + status = "disabled"; + }; + + ipmmu_sy1: mmu@e6290000 { + compatible = "renesas,ipmmu-vmsa"; + reg = <0 0xe6290000 0 0x1000>; + interrupts = <0 225 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + status = "disabled"; + }; + + ipmmu_ds: mmu@e6740000 { + compatible = "renesas,ipmmu-vmsa"; + reg = <0 0xe6740000 0 0x1000>; + interrupts = <0 198 IRQ_TYPE_LEVEL_HIGH>, + <0 199 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + }; + + ipmmu_mp: mmu@ec680000 { + compatible = "renesas,ipmmu-vmsa"; + reg = <0 0xec680000 0 0x1000>; + interrupts = <0 226 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + status = "disabled"; + }; + + ipmmu_mx: mmu@fe951000 { + compatible = "renesas,ipmmu-vmsa"; + reg = <0 0xfe951000 0 0x1000>; + interrupts = <0 222 IRQ_TYPE_LEVEL_HIGH>, + <0 221 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + }; + + ipmmu_gp: mmu@e62a0000 { + compatible = "renesas,ipmmu-vmsa"; + reg = <0 0xe62a0000 0 0x1000>; + interrupts = <0 260 IRQ_TYPE_LEVEL_HIGH>, + <0 261 IRQ_TYPE_LEVEL_HIGH>; + #iommu-cells = <1>; + status = "disabled"; + }; }; diff --git a/arch/arm/boot/dts/rk3188-radxarock.dts b/arch/arm/boot/dts/rk3188-radxarock.dts index 9a09579b8309..bdf85701987d 100644 --- a/arch/arm/boot/dts/rk3188-radxarock.dts +++ b/arch/arm/boot/dts/rk3188-radxarock.dts @@ -103,6 +103,14 @@ regulator-always-on; regulator-boot-on; }; + + vsys: vsys-regulator { + compatible = "regulator-fixed"; + regulator-name = "vsys"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + }; }; &emac { @@ -148,6 +156,14 @@ pinctrl-names = "default"; pinctrl-0 = <&act8846_dvs0_ctl>; + vp1-supply = <&vsys>; + vp2-supply = <&vsys>; + vp3-supply = <&vsys>; + vp4-supply = <&vsys>; + inl1-supply = <&vcc_io>; + inl2-supply = <&vsys>; + inl3-supply = <&vsys>; + regulators { vcc_ddr: REG1 { regulator-name = "VCC_DDR"; diff --git a/arch/arm/boot/dts/rk3288-evb-act8846.dts b/arch/arm/boot/dts/rk3288-evb-act8846.dts index d7b8bbc0c25f..1687e8336994 100644 --- a/arch/arm/boot/dts/rk3288-evb-act8846.dts +++ b/arch/arm/boot/dts/rk3288-evb-act8846.dts @@ -33,6 +33,7 @@ regulator-max-microvolt = <1350000>; regulator-always-on; regulator-boot-on; + vin-supply = <&vcc_sys>; }; vdd_gpu: syr828@41 { @@ -43,6 +44,7 @@ regulator-min-microvolt = <850000>; regulator-max-microvolt = <1350000>; regulator-always-on; + vin-supply = <&vcc_sys>; }; hym8563@51 { @@ -64,6 +66,14 @@ reg = <0x5a>; status = "okay"; + vp1-supply = <&vcc_sys>; + vp2-supply = <&vcc_sys>; + vp3-supply = <&vcc_sys>; + vp4-supply = <&vcc_sys>; + inl1-supply = <&vcc_io>; + inl2-supply = <&vcc_sys>; + inl3-supply = <&vcc_20>; + regulators { vcc_ddr: REG1 { regulator-name = "VCC_DDR"; diff --git a/arch/arm/boot/dts/rk3288-evb-rk808.dts b/arch/arm/boot/dts/rk3288-evb-rk808.dts index a1c294bf7fed..f62ea78754a9 100644 --- a/arch/arm/boot/dts/rk3288-evb-rk808.dts +++ b/arch/arm/boot/dts/rk3288-evb-rk808.dts @@ -43,9 +43,16 @@ #clock-cells = <1>; clock-output-names = "xin32k", "rk808-clkout2"; + vcc1-supply = <&vcc_sys>; + vcc2-supply = <&vcc_sys>; + vcc3-supply = <&vcc_sys>; + vcc4-supply = <&vcc_sys>; + vcc6-supply = <&vcc_sys>; + vcc7-supply = <&vcc_sys>; vcc8-supply = <&vcc_18>; vcc9-supply = <&vcc_io>; vcc10-supply = <&vcc_io>; + vcc11-supply = <&vcc_sys>; vcc12-supply = <&vcc_io>; vddio-supply = <&vccio_pmu>; diff --git a/arch/arm/boot/dts/rk3288-evb.dtsi b/arch/arm/boot/dts/rk3288-evb.dtsi index 5e895a514a0b..4a457518d861 100644 --- a/arch/arm/boot/dts/rk3288-evb.dtsi +++ b/arch/arm/boot/dts/rk3288-evb.dtsi @@ -103,6 +103,15 @@ regulator-always-on; regulator-boot-on; }; + + vcc_sys: vsys-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc_sys"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + }; }; &emmc { @@ -238,6 +247,10 @@ }; }; +&usbphy { + status = "okay"; +}; + &usb_host0_ehci { status = "okay"; }; diff --git a/arch/arm/boot/dts/rk3288-firefly.dtsi b/arch/arm/boot/dts/rk3288-firefly.dtsi index e6f873abbe0d..b54dd78580c1 100644 --- a/arch/arm/boot/dts/rk3288-firefly.dtsi +++ b/arch/arm/boot/dts/rk3288-firefly.dtsi @@ -179,6 +179,22 @@ status = "okay"; }; +&gmac { + assigned-clocks = <&cru SCLK_MAC>; + assigned-clock-parents = <&ext_gmac>; + clock_in_out = "input"; + pinctrl-names = "default"; + pinctrl-0 = <&rgmii_pins>, <&phy_rst>, <&phy_pmeb>, <&phy_int>; + phy-supply = <&vcc_lan>; + phy-mode = "rgmii"; + snps,reset-active-low; + snps,reset-delays-us = <0 10000 1000000>; + snps,reset-gpio = <&gpio4 8 GPIO_ACTIVE_LOW>; + tx_delay = <0x30>; + rx_delay = <0x10>; + status = "ok"; +}; + &hdmi { ddc-i2c-bus = <&i2c5>; status = "okay"; @@ -459,6 +475,10 @@ status = "okay"; }; +&usbphy { + status = "okay"; +}; + &usb_host1 { pinctrl-names = "default"; pinctrl-0 = <&usbhub_rst>; diff --git a/arch/arm/boot/dts/rk3288-popmetal.dts b/arch/arm/boot/dts/rk3288-popmetal.dts new file mode 100644 index 000000000000..d081f0e0da36 --- /dev/null +++ b/arch/arm/boot/dts/rk3288-popmetal.dts @@ -0,0 +1,447 @@ +/* + * Copyright (c) 2014, 2015 Andy Yan <[email protected]> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; + +#include "rk3288.dtsi" + +/ { + model = "PopMetal-RK3288"; + compatible = "chipspark,popmetal-rk3288", "rockchip,rk3288"; + + memory{ + reg = <0 0x80000000>; + }; + + ext_gmac: external-gmac-clock { + compatible = "fixed-clock"; + clock-frequency = <125000000>; + clock-output-names = "ext_gmac"; + #clock-cells = <0>; + }; + + gpio-keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + autorepeat; + + pinctrl-names = "default"; + pinctrl-0 = <&pwrbtn>; + + button@0 { + gpios = <&gpio0 5 GPIO_ACTIVE_LOW>; + linux,code = <116>; + label = "GPIO Key Power"; + linux,input-type = <1>; + gpio-key,wakeup = <1>; + debounce-interval = <100>; + }; + }; + + ir: ir-receiver { + compatible = "gpio-ir-receiver"; + gpios = <&gpio0 6 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&ir_int>; + }; + + vcc_sys: vsys-regulator { + compatible = "regulator-fixed"; + regulator-name = "vcc_sys"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + }; +}; + +&cpu0 { + cpu0-supply = <&vdd_cpu>; +}; + +&emmc { + broken-cd; + bus-width = <8>; + cap-mmc-highspeed; + disable-wp; + non-removable; + num-slots = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_pwr &emmc_bus8>; + status = "okay"; +}; + +&sdmmc { + bus-width = <4>; + cap-mmc-highspeed; + cap-sd-highspeed; + card-detect-delay = <200>; + disable-wp; /* wp not hooked up */ + num-slots = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>; + status = "okay"; +}; + +&gmac { + phy-supply = <&vcc_lan>; + phy-mode = "rgmii"; + clock_in_out = "input"; + snps,reset-gpio = <&gpio4 7 0>; + snps,reset-active-low; + snps,reset-delays-us = <0 10000 1000000>; + assigned-clocks = <&cru SCLK_MAC>; + assigned-clock-parents = <&ext_gmac>; + pinctrl-names = "default"; + pinctrl-0 = <&rgmii_pins>; + tx_delay = <0x30>; + rx_delay = <0x10>; + status = "ok"; +}; + +&hdmi { + ddc-i2c-bus = <&i2c5>; + status = "okay"; +}; + +&i2c0 { + status = "okay"; + clock-frequency = <400000>; + + rk808: pmic@1b { + compatible = "rockchip,rk808"; + reg = <0x1b>; + interrupt-parent = <&gpio0>; + interrupts = <4 IRQ_TYPE_LEVEL_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&pmic_int &global_pwroff>; + rockchip,system-power-controller; + wakeup-source; + #clock-cells = <1>; + clock-output-names = "xin32k", "rk808-clkout2"; + + vcc1-supply = <&vcc_sys>; + vcc2-supply = <&vcc_sys>; + vcc3-supply = <&vcc_sys>; + vcc4-supply = <&vcc_sys>; + vcc6-supply = <&vcc_sys>; + vcc7-supply = <&vcc_sys>; + vcc8-supply = <&vcc_18>; + vcc9-supply = <&vcc_io>; + vcc10-supply = <&vcc_io>; + vcc11-supply = <&vcc_sys>; + vcc12-supply = <&vcc_io>; + vddio-supply = <&vcc_io>; + + regulators { + vdd_cpu: DCDC_REG1 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <1350000>; + regulator-name = "vdd_arm"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdd_gpu: DCDC_REG2 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1250000>; + regulator-name = "vdd_gpu"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1000000>; + }; + }; + + vcc_ddr: DCDC_REG3 { + regulator-always-on; + regulator-boot-on; + regulator-name = "vcc_ddr"; + regulator-state-mem { + regulator-on-in-suspend; + }; + }; + + vcc_io: DCDC_REG4 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc_io"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <3300000>; + }; + }; + + vcc_lan: LDO_REG1 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc_lan"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <3300000>; + }; + }; + + vccio_sd: LDO_REG2 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vccio_sd"; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + vdd_10: LDO_REG3 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-name = "vdd_10"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1000000>; + }; + }; + + vcc18_lcd: LDO_REG4 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc18_lcd"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1800000>; + }; + }; + + ldo5: LDO_REG5 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-name = "ldo5"; + }; + + vdd10_lcd: LDO_REG6 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-name = "vdd10_lcd"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1000000>; + }; + }; + + vcc_18: LDO_REG7 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc_18"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1800000>; + }; + }; + + vcca_codec: LDO_REG8 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcca_codec"; + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <3300000>; + }; + }; + + vcc_wl: SWITCH_REG1 { + regulator-always-on; + regulator-boot-on; + regulator-name = "vcc_wl"; + regulator-state-mem { + regulator-on-in-suspend; + }; + }; + + vcc_lcd: SWITCH_REG2 { + regulator-always-on; + regulator-boot-on; + regulator-name = "vcc_lcd"; + regulator-state-mem { + regulator-on-in-suspend; + }; + }; + }; + }; +}; + +&i2c1 { + status = "okay"; + clock-frequency = <400000>; + + ak8963: ak8963@0d { + compatible = "asahi-kasei,ak8975"; + reg = <0x0d>; + interrupt-parent = <&gpio8>; + interrupts = <1 IRQ_TYPE_EDGE_RISING>; + pinctrl-names = "default"; + pinctrl-0 = <&comp_int>; + }; + + l3g4200d: l3g4200d@68 { + compatible = "st,l3g4200d-gyro"; + st,drdy-int-pin = <2>; + reg = <0x6b>; + }; + + mma8452: mma8452@1d { + compatible = "fsl,mma8452"; + reg = <0x1d>; + interrupt-parent = <&gpio8>; + interrupts = <0 IRQ_TYPE_EDGE_RISING>; + pinctrl-names = "default"; + pinctrl-0 = <&gsensor_int>; + }; +}; + +&i2c2 { + status = "okay"; +}; + +&i2c3 { + status = "okay"; +}; + +&i2c4 { + status = "okay"; +}; + +&i2c5 { + status = "okay"; +}; + +&pinctrl { + ak8963 { + comp_int: comp-int { + rockchip,pins = <8 1 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + + buttons { + pwrbtn: pwrbtn { + rockchip,pins = <0 5 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + + ir { + ir_int: ir-int { + rockchip,pins = <0 6 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + + mma8452 { + gsensor_int: gsensor-int { + rockchip,pins = <8 0 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + + pmic { + pmic_int: pmic-int { + rockchip,pins = <RK_GPIO0 4 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; +}; + +&vopb { + status = "okay"; +}; + +&vopb_mmu { + status = "okay"; +}; + +&vopl { + status = "okay"; +}; + +&vopl_mmu { + status = "okay"; +}; + +&uart0 { + status = "okay"; +}; + +&uart1 { + status = "okay"; +}; + +&uart2 { + status = "okay"; +}; + +&uart3 { + status = "okay"; +}; + +&uart4 { + status = "okay"; +}; + +&usbphy { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/rk3288.dtsi b/arch/arm/boot/dts/rk3288.dtsi index d771f687a13b..2c29a3e8bd43 100644 --- a/arch/arm/boot/dts/rk3288.dtsi +++ b/arch/arm/boot/dts/rk3288.dtsi @@ -419,6 +419,8 @@ interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cru HCLK_USBHOST0>; clock-names = "usbhost"; + phys = <&usbphy1>; + phy-names = "usb"; status = "disabled"; }; @@ -431,6 +433,8 @@ interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cru HCLK_USBHOST1>; clock-names = "otg"; + phys = <&usbphy2>; + phy-names = "usb2-phy"; status = "disabled"; }; @@ -441,6 +445,8 @@ interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cru HCLK_OTG0>; clock-names = "otg"; + phys = <&usbphy0>; + phy-names = "usb2-phy"; status = "disabled"; }; @@ -697,6 +703,35 @@ interrupts = <GIC_PPI 9 0xf04>; }; + usbphy: phy { + compatible = "rockchip,rk3288-usb-phy"; + rockchip,grf = <&grf>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + + usbphy0: usb-phy0 { + #phy-cells = <0>; + reg = <0x320>; + clocks = <&cru SCLK_OTGPHY0>; + clock-names = "phyclk"; + }; + + usbphy1: usb-phy1 { + #phy-cells = <0>; + reg = <0x334>; + clocks = <&cru SCLK_OTGPHY1>; + clock-names = "phyclk"; + }; + + usbphy2: usb-phy2 { + #phy-cells = <0>; + reg = <0x348>; + clocks = <&cru SCLK_OTGPHY2>; + clock-names = "phyclk"; + }; + }; + pinctrl: pinctrl { compatible = "rockchip,rk3288-pinctrl"; rockchip,grf = <&grf>; diff --git a/arch/arm/boot/dts/sama5d3.dtsi b/arch/arm/boot/dts/sama5d3.dtsi index 261311bdf65b..e30fee2edd55 100644 --- a/arch/arm/boot/dts/sama5d3.dtsi +++ b/arch/arm/boot/dts/sama5d3.dtsi @@ -1248,7 +1248,6 @@ atmel,watchdog-type = "hardware"; atmel,reset-type = "all"; atmel,dbg-halt; - atmel,idle-halt; status = "disabled"; }; diff --git a/arch/arm/boot/dts/sama5d35ek.dts b/arch/arm/boot/dts/sama5d35ek.dts index 9089c7c6cea8..d9a9aca1ccfd 100644 --- a/arch/arm/boot/dts/sama5d35ek.dts +++ b/arch/arm/boot/dts/sama5d35ek.dts @@ -44,8 +44,6 @@ gpio_keys { compatible = "gpio-keys"; - #address-cells = <1>; - #size-cells = <0>; pb_user1 { label = "pb_user1"; diff --git a/arch/arm/boot/dts/sama5d3_can.dtsi b/arch/arm/boot/dts/sama5d3_can.dtsi index eaf41451ad0c..c5a3772741bf 100644 --- a/arch/arm/boot/dts/sama5d3_can.dtsi +++ b/arch/arm/boot/dts/sama5d3_can.dtsi @@ -1,5 +1,5 @@ /* - * at91sama5d3_can.dtsi - Device Tree Include file for AT91SAM9x5 SoC with + * sama5d3_can.dtsi - Device Tree Include file for SAMA5D3 SoC with * CAN support * * Copyright (C) 2013 Boris BREZILLON <[email protected]> diff --git a/arch/arm/boot/dts/sama5d3_emac.dtsi b/arch/arm/boot/dts/sama5d3_emac.dtsi index fe2af9276312..ca4094d8d0fc 100644 --- a/arch/arm/boot/dts/sama5d3_emac.dtsi +++ b/arch/arm/boot/dts/sama5d3_emac.dtsi @@ -1,5 +1,5 @@ /* - * at91sama5d3_emac.dtsi - Device Tree Include file for AT91SAM9x5 SoC with + * sama5d3_emac.dtsi - Device Tree Include file for SAMA5D3 SoC with * Ethernet. * * Copyright (C) 2013 Boris BREZILLON <[email protected]> diff --git a/arch/arm/boot/dts/sama5d3_gmac.dtsi b/arch/arm/boot/dts/sama5d3_gmac.dtsi index de5ed59fb446..23f225fbb756 100644 --- a/arch/arm/boot/dts/sama5d3_gmac.dtsi +++ b/arch/arm/boot/dts/sama5d3_gmac.dtsi @@ -1,5 +1,5 @@ /* - * at91sama5d3_gmac.dtsi - Device Tree Include file for AT91SAM9x5 SoC with + * sama5d3_gmac.dtsi - Device Tree Include file for SAMA5D3 SoC with * Gigabit Ethernet. * * Copyright (C) 2013 Boris BREZILLON <[email protected]> diff --git a/arch/arm/boot/dts/sama5d3_lcd.dtsi b/arch/arm/boot/dts/sama5d3_lcd.dtsi index 85d302701565..8aeff6c122aa 100644 --- a/arch/arm/boot/dts/sama5d3_lcd.dtsi +++ b/arch/arm/boot/dts/sama5d3_lcd.dtsi @@ -1,5 +1,5 @@ /* - * at91sama5d3_lcd.dtsi - Device Tree Include file for AT91SAM9x5 SoC with + * sama5d3_lcd.dtsi - Device Tree Include file for SAMA5D3 SoC with * LCD support * * Copyright (C) 2013 Boris BREZILLON <[email protected]> diff --git a/arch/arm/boot/dts/sama5d3_mci2.dtsi b/arch/arm/boot/dts/sama5d3_mci2.dtsi index 1b02208ea6ff..026b252f09b3 100644 --- a/arch/arm/boot/dts/sama5d3_mci2.dtsi +++ b/arch/arm/boot/dts/sama5d3_mci2.dtsi @@ -1,5 +1,5 @@ /* - * at91sama5d3_mci2.dtsi - Device Tree Include file for AT91SAM9x5 SoC with + * sama5d3_mci2.dtsi - Device Tree Include file for SAMA5D3 SoC with * 3 MMC ports * * Copyright (C) 2013 Boris BREZILLON <[email protected]> diff --git a/arch/arm/boot/dts/sama5d3_tcb1.dtsi b/arch/arm/boot/dts/sama5d3_tcb1.dtsi index 02848453ca0c..f7fa58fe09f1 100644 --- a/arch/arm/boot/dts/sama5d3_tcb1.dtsi +++ b/arch/arm/boot/dts/sama5d3_tcb1.dtsi @@ -1,5 +1,5 @@ /* - * at91sama5d3_tcb1.dtsi - Device Tree Include file for AT91SAM9x5 SoC with + * sama5d3_tcb1.dtsi - Device Tree Include file for SAMA5D3 SoC with * 2 TC blocks. * * Copyright (C) 2013 Boris BREZILLON <[email protected]> diff --git a/arch/arm/boot/dts/sama5d3_uart.dtsi b/arch/arm/boot/dts/sama5d3_uart.dtsi index 7a8d4c6115f7..2511d748867b 100644 --- a/arch/arm/boot/dts/sama5d3_uart.dtsi +++ b/arch/arm/boot/dts/sama5d3_uart.dtsi @@ -1,5 +1,5 @@ /* - * at91sama5d3_uart.dtsi - Device Tree Include file for AT91SAM9x5 SoC with + * sama5d3_uart.dtsi - Device Tree Include file for SAMA5D3 SoC with * UART support * * Copyright (C) 2013 Boris BREZILLON <[email protected]> diff --git a/arch/arm/boot/dts/sama5d4.dtsi b/arch/arm/boot/dts/sama5d4.dtsi index d986b41b9654..63eb7a2c08f7 100644 --- a/arch/arm/boot/dts/sama5d4.dtsi +++ b/arch/arm/boot/dts/sama5d4.dtsi @@ -64,8 +64,13 @@ gpio2 = &pioC; gpio3 = &pioD; gpio4 = &pioE; + pwm0 = &pwm0; + ssc0 = &ssc0; + ssc1 = &ssc1; tcb0 = &tcb0; tcb1 = &tcb1; + i2c0 = &i2c0; + i2c1 = &i2c1; i2c2 = &i2c2; }; cpus { @@ -318,6 +323,21 @@ clock-names = "dma_clk"; }; + isi: isi@f0008000 { + compatible = "atmel,at91sam9g45-isi"; + reg = <0xf0008000 0x4000>; + interrupts = <52 IRQ_TYPE_LEVEL_HIGH 5>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_isi_data_0_7>; + clocks = <&isi_clk>; + clock-names = "isi_clk"; + status = "disabled"; + port { + #address-cells = <1>; + #size-cells = <0>; + }; + }; + ramc0: ramc@f0010000 { compatible = "atmel,sama5d3-ddramc"; reg = <0xf0010000 0x200>; @@ -799,6 +819,33 @@ clock-names = "mci_clk"; }; + ssc0: ssc@f8008000 { + compatible = "atmel,at91sam9g45-ssc"; + reg = <0xf8008000 0x4000>; + interrupts = <48 IRQ_TYPE_LEVEL_HIGH 0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>; + dmas = <&dma1 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) + | AT91_XDMAC_DT_PERID(26))>, + <&dma1 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) + | AT91_XDMAC_DT_PERID(27))>; + dma-names = "tx", "rx"; + clocks = <&ssc0_clk>; + clock-names = "pclk"; + status = "disabled"; + }; + + pwm0: pwm@f800c000 { + compatible = "atmel,sama5d3-pwm"; + reg = <0xf800c000 0x300>; + interrupts = <43 IRQ_TYPE_LEVEL_HIGH 4>; + #pwm-cells = <3>; + clocks = <&pwm_clk>; + status = "disabled"; + }; + spi0: spi@f8010000 { #address-cells = <1>; #size-cells = <0>; @@ -838,6 +885,25 @@ status = "disabled"; }; + i2c1: i2c@f8018000 { + compatible = "atmel,at91sam9x5-i2c"; + reg = <0xf8018000 0x4000>; + interrupts = <33 IRQ_TYPE_LEVEL_HIGH 6>; + dmas = <&dma1 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)) + AT91_XDMAC_DT_PERID(4)>, + <&dma1 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)) + AT91_XDMAC_DT_PERID(5)>; + dma-names = "tx", "rx"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&twi1_clk>; + status = "disabled"; + }; + tcb0: timer@f801c000 { compatible = "atmel,at91sam9x5-tcb"; reg = <0xf801c000 0x100>; @@ -852,6 +918,8 @@ interrupts = <54 IRQ_TYPE_LEVEL_HIGH 3>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_macb0_rmii>; + #address-cells = <1>; + #size-cells = <0>; clocks = <&macb0_clk>, <&macb0_clk>; clock-names = "hclk", "pclk"; status = "disabled"; @@ -952,6 +1020,24 @@ status = "disabled"; }; + ssc1: ssc@fc014000 { + compatible = "atmel,at91sam9g45-ssc"; + reg = <0xfc014000 0x4000>; + interrupts = <49 IRQ_TYPE_LEVEL_HIGH 0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ssc1_tx &pinctrl_ssc1_rx>; + dmas = <&dma1 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) + | AT91_XDMAC_DT_PERID(28))>, + <&dma1 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) + | AT91_XDMAC_DT_PERID(29))>; + dma-names = "tx", "rx"; + clocks = <&ssc1_clk>; + clock-names = "pclk"; + status = "disabled"; + }; + tcb1: timer@fc020000 { compatible = "atmel,at91sam9x5-tcb"; reg = <0xfc020000 0x100>; @@ -1007,6 +1093,46 @@ }; }; + aes@fc044000 { + compatible = "atmel,at91sam9g46-aes"; + reg = <0xfc044000 0x100>; + interrupts = <12 IRQ_TYPE_LEVEL_HIGH 0>; + dmas = <&dma0 (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)) + AT91_XDMAC_DT_PERID(41)>, + <&dma0 (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)) + AT91_XDMAC_DT_PERID(40)>; + dma-names = "tx", "rx"; + clocks = <&aes_clk>; + clock-names = "aes_clk"; + status = "disabled"; + }; + + tdes@fc04c000 { + compatible = "atmel,at91sam9g46-tdes"; + reg = <0xfc04c000 0x100>; + interrupts = <14 IRQ_TYPE_LEVEL_HIGH 0>; + dmas = <&dma0 (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)) + AT91_XDMAC_DT_PERID(42)>, + <&dma0 (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)) + AT91_XDMAC_DT_PERID(43)>; + dma-names = "tx", "rx"; + clocks = <&tdes_clk>; + clock-names = "tdes_clk"; + status = "disabled"; + }; + + sha@fc050000 { + compatible = "atmel,at91sam9g46-sha"; + reg = <0xfc050000 0x100>; + interrupts = <15 IRQ_TYPE_LEVEL_HIGH 0>; + dmas = <&dma0 (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)) + AT91_XDMAC_DT_PERID(44)>; + dma-names = "tx"; + clocks = <&sha_clk>; + clock-names = "sha_clk"; + status = "disabled"; + }; + rstc@fc068600 { compatible = "atmel,at91sam9g45-rstc"; reg = <0xfc068600 0x10>; @@ -1189,6 +1315,14 @@ }; }; + i2c1 { + pinctrl_i2c1: i2c1-0 { + atmel,pins = + <AT91_PIOE 29 AT91_PERIPH_C AT91_PINCTRL_NONE /* TWD1, conflicts with UART0 RX and DIBP */ + AT91_PIOE 30 AT91_PERIPH_C AT91_PINCTRL_NONE>; /* TWCK1, conflicts with UART0 TX and DIBN */ + }; + }; + i2c2 { pinctrl_i2c2: i2c2-0 { atmel,pins = @@ -1197,6 +1331,33 @@ }; }; + isi { + pinctrl_isi_data_0_7: isi-0-data-0-7 { + atmel,pins = + <AT91_PIOC 19 AT91_PERIPH_A AT91_PINCTRL_NONE /* ISI_D0 */ + AT91_PIOC 20 AT91_PERIPH_A AT91_PINCTRL_NONE /* ISI_D1 */ + AT91_PIOC 21 AT91_PERIPH_A AT91_PINCTRL_NONE /* ISI_D2 */ + AT91_PIOC 22 AT91_PERIPH_A AT91_PINCTRL_NONE /* ISI_D3 */ + AT91_PIOC 23 AT91_PERIPH_A AT91_PINCTRL_NONE /* ISI_D4 */ + AT91_PIOC 24 AT91_PERIPH_A AT91_PINCTRL_NONE /* ISI_D5 */ + AT91_PIOC 25 AT91_PERIPH_A AT91_PINCTRL_NONE /* ISI_D6 */ + AT91_PIOC 26 AT91_PERIPH_A AT91_PINCTRL_NONE /* ISI_D7 */ + AT91_PIOB 1 AT91_PERIPH_C AT91_PINCTRL_NONE /* ISI_PCK, conflict with G0_RXCK */ + AT91_PIOB 3 AT91_PERIPH_C AT91_PINCTRL_NONE /* ISI_VSYNC */ + AT91_PIOB 4 AT91_PERIPH_C AT91_PINCTRL_NONE>; /* ISI_HSYNC */ + }; + pinctrl_isi_data_8_9: isi-0-data-8-9 { + atmel,pins = + <AT91_PIOC 0 AT91_PERIPH_C AT91_PINCTRL_NONE /* ISI_D8, conflicts with SPI0_MISO, PWMH2 */ + AT91_PIOC 1 AT91_PERIPH_C AT91_PINCTRL_NONE>; /* ISI_D9, conflicts with SPI0_MOSI, PWML2 */ + }; + pinctrl_isi_data_10_11: isi-0-data-10-11 { + atmel,pins = + <AT91_PIOC 2 AT91_PERIPH_C AT91_PINCTRL_NONE /* ISI_D10, conflicts with SPI0_SPCK, PWMH3 */ + AT91_PIOC 3 AT91_PERIPH_C AT91_PINCTRL_NONE>; /* ISI_D11, conflicts with SPI0_NPCS0, PWML3 */ + }; + }; + macb0 { pinctrl_macb0_rmii: macb0_rmii-0 { atmel,pins = @@ -1280,6 +1441,38 @@ }; }; + ssc0 { + pinctrl_ssc0_tx: ssc0_tx { + atmel,pins = + <AT91_PIOB 27 AT91_PERIPH_B AT91_PINCTRL_NONE /* TK0 */ + AT91_PIOB 31 AT91_PERIPH_B AT91_PINCTRL_NONE /* TF0 */ + AT91_PIOB 28 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* TD0 */ + }; + + pinctrl_ssc0_rx: ssc0_rx { + atmel,pins = + <AT91_PIOB 26 AT91_PERIPH_B AT91_PINCTRL_NONE /* RK0 */ + AT91_PIOB 30 AT91_PERIPH_B AT91_PINCTRL_NONE /* RF0 */ + AT91_PIOB 29 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* RD0 */ + }; + }; + + ssc1 { + pinctrl_ssc1_tx: ssc1_tx { + atmel,pins = + <AT91_PIOC 19 AT91_PERIPH_B AT91_PINCTRL_NONE /* TK1 */ + AT91_PIOC 20 AT91_PERIPH_B AT91_PINCTRL_NONE /* TF1 */ + AT91_PIOC 21 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* TD1 */ + }; + + pinctrl_ssc1_rx: ssc1_rx { + atmel,pins = + <AT91_PIOC 24 AT91_PERIPH_B AT91_PINCTRL_NONE /* RK1 */ + AT91_PIOC 22 AT91_PERIPH_B AT91_PINCTRL_NONE /* RF1 */ + AT91_PIOC 23 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* RD1 */ + }; + }; + usart2 { pinctrl_usart2: usart2-0 { atmel,pins = diff --git a/arch/arm/boot/dts/sh73a0-kzm9g-reference.dts b/arch/arm/boot/dts/sh73a0-kzm9g-reference.dts index 6d32c87632d4..bf365f7fef47 100644 --- a/arch/arm/boot/dts/sh73a0-kzm9g-reference.dts +++ b/arch/arm/boot/dts/sh73a0-kzm9g-reference.dts @@ -45,7 +45,7 @@ memory { device_type = "memory"; - reg = <0x41000000 0x1e800000>; + reg = <0x40000000 0x20000000>; }; reg_1p8v: regulator@0 { @@ -188,6 +188,33 @@ &i2c0 { status = "okay"; + + compass@c { + compatible = "asahi-kasei,ak8975"; + reg = <0x0c>; + interrupt-parent = <&irqpin3>; + interrupts = <4 IRQ_TYPE_EDGE_FALLING>; + }; + + ak4648: codec@12 { + compatible = "asahi-kasei,ak4648"; + reg = <0x12>; + #sound-dai-cells = <0>; + }; + + accelerometer@1d { + compatible = "adi,adxl34x"; + reg = <0x1d>; + interrupt-parent = <&irqpin3>; + interrupts = <2 IRQ_TYPE_LEVEL_HIGH>, + <3 IRQ_TYPE_LEVEL_HIGH>; + }; + + rtc@32 { + compatible = "ricoh,r2025sd"; + reg = <0x32>; + }; + as3711@40 { compatible = "ams,as3711"; reg = <0x40>; @@ -258,11 +285,16 @@ }; }; }; +}; - ak4648: ak4648@12 { - #sound-dai-cells = <0>; - compatible = "asahi-kasei,ak4648"; - reg = <0x12>; +&i2c1 { + status = "okay"; + + touchscreen@55 { + compatible = "sitronix,st1232"; + reg = <0x55>; + interrupt-parent = <&irqpin1>; + interrupts = <0 IRQ_TYPE_EDGE_FALLING>; }; }; diff --git a/arch/arm/boot/dts/sh73a0-kzm9g.dts b/arch/arm/boot/dts/sh73a0-kzm9g.dts index 27c5f426d172..e7dae01933a5 100644 --- a/arch/arm/boot/dts/sh73a0-kzm9g.dts +++ b/arch/arm/boot/dts/sh73a0-kzm9g.dts @@ -21,6 +21,6 @@ memory { device_type = "memory"; - reg = <0x41000000 0x1e800000>; + reg = <0x40000000 0x20000000>; }; }; diff --git a/arch/arm/boot/dts/sh73a0.dtsi b/arch/arm/boot/dts/sh73a0.dtsi index 2dfd5b44255d..ab319b73e282 100644 --- a/arch/arm/boot/dts/sh73a0.dtsi +++ b/arch/arm/boot/dts/sh73a0.dtsi @@ -94,6 +94,8 @@ 0 6 IRQ_TYPE_LEVEL_HIGH 0 7 IRQ_TYPE_LEVEL_HIGH 0 8 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp5_clks SH73A0_CLK_INTCA0>; + control-parent; }; irqpin1: irqpin@e6900004 { @@ -113,6 +115,7 @@ 0 14 IRQ_TYPE_LEVEL_HIGH 0 15 IRQ_TYPE_LEVEL_HIGH 0 16 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp5_clks SH73A0_CLK_INTCA0>; control-parent; }; @@ -133,6 +136,8 @@ 0 22 IRQ_TYPE_LEVEL_HIGH 0 23 IRQ_TYPE_LEVEL_HIGH 0 24 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp5_clks SH73A0_CLK_INTCA0>; + control-parent; }; irqpin3: irqpin@e690000c { @@ -152,6 +157,8 @@ 0 30 IRQ_TYPE_LEVEL_HIGH 0 31 IRQ_TYPE_LEVEL_HIGH 0 32 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp5_clks SH73A0_CLK_INTCA0>; + control-parent; }; i2c0: i2c@e6820000 { @@ -426,133 +433,159 @@ vclk1_clk: vclk1_clk@e6150008 { compatible = "renesas,sh73a0-div6-clock", "renesas,cpg-div6-clock"; reg = <0xe6150008 4>; - clocks = <&pll1_div2_clk>; + clocks = <&pll1_div2_clk>, <&cpg_clocks SH73A0_CLK_PLL2>, + <&extcki_clk>, <&extal2_clk>, <&main_div2_clk>, + <&extalr_clk>, <&cpg_clocks SH73A0_CLK_MAIN>, + <0>; #clock-cells = <0>; clock-output-names = "vclk1"; }; vclk2_clk: vclk2_clk@e615000c { compatible = "renesas,sh73a0-div6-clock", "renesas,cpg-div6-clock"; reg = <0xe615000c 4>; - clocks = <&pll1_div2_clk>; + clocks = <&pll1_div2_clk>, <&cpg_clocks SH73A0_CLK_PLL2>, + <&extcki_clk>, <&extal2_clk>, <&main_div2_clk>, + <&extalr_clk>, <&cpg_clocks SH73A0_CLK_MAIN>, + <0>; #clock-cells = <0>; clock-output-names = "vclk2"; }; vclk3_clk: vclk3_clk@e615001c { compatible = "renesas,sh73a0-div6-clock", "renesas,cpg-div6-clock"; reg = <0xe615001c 4>; - clocks = <&pll1_div2_clk>; + clocks = <&pll1_div2_clk>, <&cpg_clocks SH73A0_CLK_PLL2>, + <&extcki_clk>, <&extal2_clk>, <&main_div2_clk>, + <&extalr_clk>, <&cpg_clocks SH73A0_CLK_MAIN>, + <0>; #clock-cells = <0>; clock-output-names = "vclk3"; }; zb_clk: zb_clk@e6150010 { compatible = "renesas,sh73a0-div6-clock", "renesas,cpg-div6-clock"; reg = <0xe6150010 4>; - clocks = <&pll1_div2_clk>; + clocks = <&pll1_div2_clk>, <0>, + <&cpg_clocks SH73A0_CLK_PLL2>, <0>; #clock-cells = <0>; clock-output-names = "zb"; }; flctl_clk: flctl_clk@e6150014 { compatible = "renesas,sh73a0-div6-clock", "renesas,cpg-div6-clock"; reg = <0xe6150014 4>; - clocks = <&pll1_div2_clk>; + clocks = <&pll1_div2_clk>, <0>, + <&cpg_clocks SH73A0_CLK_PLL2>, <0>; #clock-cells = <0>; clock-output-names = "flctlck"; }; sdhi0_clk: sdhi0_clk@e6150074 { compatible = "renesas,sh73a0-div6-clock", "renesas,cpg-div6-clock"; reg = <0xe6150074 4>; - clocks = <&pll1_div2_clk>; + clocks = <&pll1_div2_clk>, <&cpg_clocks SH73A0_CLK_PLL2>, + <&pll1_div13_clk>, <0>; #clock-cells = <0>; clock-output-names = "sdhi0ck"; }; sdhi1_clk: sdhi1_clk@e6150078 { compatible = "renesas,sh73a0-div6-clock", "renesas,cpg-div6-clock"; reg = <0xe6150078 4>; - clocks = <&pll1_div2_clk>; + clocks = <&pll1_div2_clk>, <&cpg_clocks SH73A0_CLK_PLL2>, + <&pll1_div13_clk>, <0>; #clock-cells = <0>; clock-output-names = "sdhi1ck"; }; sdhi2_clk: sdhi2_clk@e615007c { compatible = "renesas,sh73a0-div6-clock", "renesas,cpg-div6-clock"; reg = <0xe615007c 4>; - clocks = <&pll1_div2_clk>; + clocks = <&pll1_div2_clk>, <&cpg_clocks SH73A0_CLK_PLL2>, + <&pll1_div13_clk>, <0>; #clock-cells = <0>; clock-output-names = "sdhi2ck"; }; fsia_clk: fsia_clk@e6150018 { compatible = "renesas,sh73a0-div6-clock", "renesas,cpg-div6-clock"; reg = <0xe6150018 4>; - clocks = <&pll1_div2_clk>; + clocks = <&pll1_div2_clk>, <&cpg_clocks SH73A0_CLK_PLL2>, + <&fsiack_clk>, <&fsiack_clk>; #clock-cells = <0>; clock-output-names = "fsia"; }; fsib_clk: fsib_clk@e6150090 { compatible = "renesas,sh73a0-div6-clock", "renesas,cpg-div6-clock"; reg = <0xe6150090 4>; - clocks = <&pll1_div2_clk>; + clocks = <&pll1_div2_clk>, <&cpg_clocks SH73A0_CLK_PLL2>, + <&fsibck_clk>, <&fsibck_clk>; #clock-cells = <0>; clock-output-names = "fsib"; }; sub_clk: sub_clk@e6150080 { compatible = "renesas,sh73a0-div6-clock", "renesas,cpg-div6-clock"; reg = <0xe6150080 4>; - clocks = <&extal2_clk>; + clocks = <&pll1_div2_clk>, <&cpg_clocks SH73A0_CLK_PLL2>, + <&extal2_clk>, <&extal2_clk>; #clock-cells = <0>; clock-output-names = "sub"; }; spua_clk: spua_clk@e6150084 { compatible = "renesas,sh73a0-div6-clock", "renesas,cpg-div6-clock"; reg = <0xe6150084 4>; - clocks = <&pll1_div2_clk>; + clocks = <&pll1_div2_clk>, <&cpg_clocks SH73A0_CLK_PLL2>, + <&extal2_clk>, <&extal2_clk>; #clock-cells = <0>; clock-output-names = "spua"; }; spuv_clk: spuv_clk@e6150094 { compatible = "renesas,sh73a0-div6-clock", "renesas,cpg-div6-clock"; reg = <0xe6150094 4>; - clocks = <&pll1_div2_clk>; + clocks = <&pll1_div2_clk>, <&cpg_clocks SH73A0_CLK_PLL2>, + <&extal2_clk>, <&extal2_clk>; #clock-cells = <0>; clock-output-names = "spuv"; }; msu_clk: msu_clk@e6150088 { compatible = "renesas,sh73a0-div6-clock", "renesas,cpg-div6-clock"; reg = <0xe6150088 4>; - clocks = <&pll1_div2_clk>; + clocks = <&pll1_div2_clk>, <0>, + <&cpg_clocks SH73A0_CLK_PLL2>, <0>; #clock-cells = <0>; clock-output-names = "msu"; }; hsi_clk: hsi_clk@e615008c { compatible = "renesas,sh73a0-div6-clock", "renesas,cpg-div6-clock"; reg = <0xe615008c 4>; - clocks = <&pll1_div2_clk>; + clocks = <&pll1_div2_clk>, <&cpg_clocks SH73A0_CLK_PLL2>, + <&pll1_div7_clk>, <0>; #clock-cells = <0>; clock-output-names = "hsi"; }; mfg1_clk: mfg1_clk@e6150098 { compatible = "renesas,sh73a0-div6-clock", "renesas,cpg-div6-clock"; reg = <0xe6150098 4>; - clocks = <&pll1_div2_clk>; + clocks = <&pll1_div2_clk>, <0>, + <&cpg_clocks SH73A0_CLK_PLL2>, <0>; #clock-cells = <0>; clock-output-names = "mfg1"; }; mfg2_clk: mfg2_clk@e615009c { compatible = "renesas,sh73a0-div6-clock", "renesas,cpg-div6-clock"; reg = <0xe615009c 4>; - clocks = <&pll1_div2_clk>; + clocks = <&pll1_div2_clk>, <0>, + <&cpg_clocks SH73A0_CLK_PLL2>, <0>; #clock-cells = <0>; clock-output-names = "mfg2"; }; dsit_clk: dsit_clk@e6150060 { compatible = "renesas,sh73a0-div6-clock", "renesas,cpg-div6-clock"; reg = <0xe6150060 4>; - clocks = <&pll1_div2_clk>; + clocks = <&pll1_div2_clk>, <0>, + <&cpg_clocks SH73A0_CLK_PLL2>, <0>; #clock-cells = <0>; clock-output-names = "dsit"; }; dsi0p_clk: dsi0p_clk@e6150064 { compatible = "renesas,sh73a0-div6-clock", "renesas,cpg-div6-clock"; reg = <0xe6150064 4>; - clocks = <&pll1_div2_clk>; + clocks = <&pll1_div2_clk>, <&cpg_clocks SH73A0_CLK_PLL2>, + <&cpg_clocks SH73A0_CLK_MAIN>, <&extal2_clk>, + <&extcki_clk>, <0>, <0>, <0>; #clock-cells = <0>; clock-output-names = "dsi0pck"; }; @@ -695,5 +728,16 @@ clock-output-names = "iic3", "iic4", "keysc"; }; + mstp5_clks: mstp5_clks@e6150144 { + compatible = "renesas,sh73a0-mstp-clocks", "renesas,cpg-mstp-clocks"; + reg = <0xe6150144 4>, <0xe615003c 4>; + clocks = <&cpg_clocks SH73A0_CLK_HP>; + #clock-cells = <1>; + clock-indices = < + SH73A0_CLK_INTCA0 + >; + clock-output-names = + "intca0"; + }; }; }; diff --git a/arch/arm/configs/at91_dt_defconfig b/arch/arm/configs/at91_dt_defconfig index f2670f638e97..811e72bbe642 100644 --- a/arch/arm/configs/at91_dt_defconfig +++ b/arch/arm/configs/at91_dt_defconfig @@ -70,6 +70,7 @@ CONFIG_SCSI=y CONFIG_BLK_DEV_SD=y # CONFIG_SCSI_LOWLEVEL is not set CONFIG_NETDEVICES=y +CONFIG_ARM_AT91_ETHER=y CONFIG_MACB=y # CONFIG_NET_VENDOR_BROADCOM is not set CONFIG_DM9000=y diff --git a/arch/arm/configs/sama5_defconfig b/arch/arm/configs/sama5_defconfig index 41d856effe6c..510c747c65b4 100644 --- a/arch/arm/configs/sama5_defconfig +++ b/arch/arm/configs/sama5_defconfig @@ -3,8 +3,6 @@ CONFIG_SYSVIPC=y CONFIG_IRQ_DOMAIN_DEBUG=y CONFIG_LOG_BUF_SHIFT=14 -CONFIG_SYSFS_DEPRECATED=y -CONFIG_SYSFS_DEPRECATED_V2=y CONFIG_BLK_DEV_INITRD=y CONFIG_EMBEDDED=y CONFIG_SLAB=y diff --git a/arch/arm/mach-at91/pm.c b/arch/arm/mach-at91/pm.c index 5e34fb143309..aa4116e9452f 100644 --- a/arch/arm/mach-at91/pm.c +++ b/arch/arm/mach-at91/pm.c @@ -270,37 +270,35 @@ static void __init at91_pm_sram_init(void) phys_addr_t sram_pbase; unsigned long sram_base; struct device_node *node; - struct platform_device *pdev; + struct platform_device *pdev = NULL; - node = of_find_compatible_node(NULL, NULL, "mmio-sram"); - if (!node) { - pr_warn("%s: failed to find sram node!\n", __func__); - return; + for_each_compatible_node(node, NULL, "mmio-sram") { + pdev = of_find_device_by_node(node); + if (pdev) { + of_node_put(node); + break; + } } - pdev = of_find_device_by_node(node); if (!pdev) { pr_warn("%s: failed to find sram device!\n", __func__); - goto put_node; + return; } sram_pool = dev_get_gen_pool(&pdev->dev); if (!sram_pool) { pr_warn("%s: sram pool unavailable!\n", __func__); - goto put_node; + return; } sram_base = gen_pool_alloc(sram_pool, at91_slow_clock_sz); if (!sram_base) { pr_warn("%s: unable to alloc ocram!\n", __func__); - goto put_node; + return; } sram_pbase = gen_pool_virt_to_phys(sram_pool, sram_base); slow_clock = __arm_ioremap_exec(sram_pbase, at91_slow_clock_sz, false); - -put_node: - of_node_put(node); } #endif diff --git a/arch/arm/mach-at91/pm.h b/arch/arm/mach-at91/pm.h index d2c89963af2d..86c0aa819d25 100644 --- a/arch/arm/mach-at91/pm.h +++ b/arch/arm/mach-at91/pm.h @@ -44,7 +44,7 @@ static inline void at91rm9200_standby(void) " mcr p15, 0, %0, c7, c0, 4\n\t" " str %5, [%1, %2]" : - : "r" (0), "r" (AT91_BASE_SYS), "r" (AT91RM9200_SDRAMC_LPR), + : "r" (0), "r" (at91_ramc_base[0]), "r" (AT91RM9200_SDRAMC_LPR), "r" (1), "r" (AT91RM9200_SDRAMC_SRR), "r" (lpr)); } diff --git a/arch/arm/mach-at91/pm_slowclock.S b/arch/arm/mach-at91/pm_slowclock.S index 556151e85ec4..a2cc49f96f61 100644 --- a/arch/arm/mach-at91/pm_slowclock.S +++ b/arch/arm/mach-at91/pm_slowclock.S @@ -25,11 +25,6 @@ */ #undef SLOWDOWN_MASTER_CLOCK -#define MCKRDY_TIMEOUT 1000 -#define MOSCRDY_TIMEOUT 1000 -#define PLLALOCK_TIMEOUT 1000 -#define PLLBLOCK_TIMEOUT 1000 - pmc .req r0 sdramc .req r1 ramc1 .req r2 @@ -41,56 +36,36 @@ tmp2 .req r5 * Wait until master clock is ready (after switching master clock source) */ .macro wait_mckrdy - mov tmp2, #MCKRDY_TIMEOUT -1: sub tmp2, tmp2, #1 - cmp tmp2, #0 - beq 2f - ldr tmp1, [pmc, #AT91_PMC_SR] +1: ldr tmp1, [pmc, #AT91_PMC_SR] tst tmp1, #AT91_PMC_MCKRDY beq 1b -2: .endm /* * Wait until master oscillator has stabilized. */ .macro wait_moscrdy - mov tmp2, #MOSCRDY_TIMEOUT -1: sub tmp2, tmp2, #1 - cmp tmp2, #0 - beq 2f - ldr tmp1, [pmc, #AT91_PMC_SR] +1: ldr tmp1, [pmc, #AT91_PMC_SR] tst tmp1, #AT91_PMC_MOSCS beq 1b -2: .endm /* * Wait until PLLA has locked. */ .macro wait_pllalock - mov tmp2, #PLLALOCK_TIMEOUT -1: sub tmp2, tmp2, #1 - cmp tmp2, #0 - beq 2f - ldr tmp1, [pmc, #AT91_PMC_SR] +1: ldr tmp1, [pmc, #AT91_PMC_SR] tst tmp1, #AT91_PMC_LOCKA beq 1b -2: .endm /* * Wait until PLLB has locked. */ .macro wait_pllblock - mov tmp2, #PLLBLOCK_TIMEOUT -1: sub tmp2, tmp2, #1 - cmp tmp2, #0 - beq 2f - ldr tmp1, [pmc, #AT91_PMC_SR] +1: ldr tmp1, [pmc, #AT91_PMC_SR] tst tmp1, #AT91_PMC_LOCKB beq 1b -2: .endm .text @@ -134,6 +109,16 @@ ddr_sr_enable: cmp memctrl, #AT91_MEMCTRL_DDRSDR bne sdr_sr_enable + /* LPDDR1 --> force DDR2 mode during self-refresh */ + ldr tmp1, [sdramc, #AT91_DDRSDRC_MDR] + str tmp1, .saved_sam9_mdr + bic tmp1, tmp1, #~AT91_DDRSDRC_MD + cmp tmp1, #AT91_DDRSDRC_MD_LOW_POWER_DDR + ldreq tmp1, [sdramc, #AT91_DDRSDRC_MDR] + biceq tmp1, tmp1, #AT91_DDRSDRC_MD + orreq tmp1, tmp1, #AT91_DDRSDRC_MD_DDR2 + streq tmp1, [sdramc, #AT91_DDRSDRC_MDR] + /* prepare for DDRAM self-refresh mode */ ldr tmp1, [sdramc, #AT91_DDRSDRC_LPR] str tmp1, .saved_sam9_lpr @@ -142,14 +127,26 @@ ddr_sr_enable: /* figure out if we use the second ram controller */ cmp ramc1, #0 - ldrne tmp2, [ramc1, #AT91_DDRSDRC_LPR] - strne tmp2, .saved_sam9_lpr1 - bicne tmp2, #AT91_DDRSDRC_LPCB - orrne tmp2, #AT91_DDRSDRC_LPCB_SELF_REFRESH + beq ddr_no_2nd_ctrl + + ldr tmp2, [ramc1, #AT91_DDRSDRC_MDR] + str tmp2, .saved_sam9_mdr1 + bic tmp2, tmp2, #~AT91_DDRSDRC_MD + cmp tmp2, #AT91_DDRSDRC_MD_LOW_POWER_DDR + ldreq tmp2, [ramc1, #AT91_DDRSDRC_MDR] + biceq tmp2, tmp2, #AT91_DDRSDRC_MD + orreq tmp2, tmp2, #AT91_DDRSDRC_MD_DDR2 + streq tmp2, [ramc1, #AT91_DDRSDRC_MDR] + + ldr tmp2, [ramc1, #AT91_DDRSDRC_LPR] + str tmp2, .saved_sam9_lpr1 + bic tmp2, #AT91_DDRSDRC_LPCB + orr tmp2, #AT91_DDRSDRC_LPCB_SELF_REFRESH /* Enable DDRAM self-refresh mode */ + str tmp2, [ramc1, #AT91_DDRSDRC_LPR] +ddr_no_2nd_ctrl: str tmp1, [sdramc, #AT91_DDRSDRC_LPR] - strne tmp2, [ramc1, #AT91_DDRSDRC_LPR] b sdr_sr_done @@ -280,12 +277,17 @@ sdr_sr_done: */ cmp memctrl, #AT91_MEMCTRL_DDRSDR bne sdr_en_restore + /* Restore MDR in case of LPDDR1 */ + ldr tmp1, .saved_sam9_mdr + str tmp1, [sdramc, #AT91_DDRSDRC_MDR] /* Restore LPR on AT91 with DDRAM */ ldr tmp1, .saved_sam9_lpr str tmp1, [sdramc, #AT91_DDRSDRC_LPR] /* if we use the second ram controller */ cmp ramc1, #0 + ldrne tmp2, .saved_sam9_mdr1 + strne tmp2, [ramc1, #AT91_DDRSDRC_MDR] ldrne tmp2, .saved_sam9_lpr1 strne tmp2, [ramc1, #AT91_DDRSDRC_LPR] @@ -319,5 +321,11 @@ ram_restored: .saved_sam9_lpr1: .word 0 +.saved_sam9_mdr: + .word 0 + +.saved_sam9_mdr1: + .word 0 + ENTRY(at91_slow_clock_sz) .word .-at91_slow_clock diff --git a/arch/arm/mach-shmobile/smp-r8a7790.c b/arch/arm/mach-shmobile/smp-r8a7790.c index 9c3da1345b8b..a5bef873d37e 100644 --- a/arch/arm/mach-shmobile/smp-r8a7790.c +++ b/arch/arm/mach-shmobile/smp-r8a7790.c @@ -37,11 +37,11 @@ static struct rcar_sysc_ch r8a7790_ca7_scu = { static struct rcar_apmu_config r8a7790_apmu_config[] = { { - .iomem = DEFINE_RES_MEM(0xe6152000, 0x88), + .iomem = DEFINE_RES_MEM(0xe6152000, 0x188), .cpus = { 0, 1, 2, 3 }, }, { - .iomem = DEFINE_RES_MEM(0xe6151000, 0x88), + .iomem = DEFINE_RES_MEM(0xe6151000, 0x188), .cpus = { 0x100, 0x0101, 0x102, 0x103 }, } }; diff --git a/arch/arm/mach-shmobile/smp-r8a7791.c b/arch/arm/mach-shmobile/smp-r8a7791.c index 7e49e0a52e32..de1d92dc1323 100644 --- a/arch/arm/mach-shmobile/smp-r8a7791.c +++ b/arch/arm/mach-shmobile/smp-r8a7791.c @@ -27,7 +27,7 @@ static struct rcar_apmu_config r8a7791_apmu_config[] = { { - .iomem = DEFINE_RES_MEM(0xe6152000, 0x88), + .iomem = DEFINE_RES_MEM(0xe6152000, 0x188), .cpus = { 0, 1 }, } }; diff --git a/include/dt-bindings/clock/r8a7790-clock.h b/include/dt-bindings/clock/r8a7790-clock.h index 91940271cf83..3f2c6b198d4a 100644 --- a/include/dt-bindings/clock/r8a7790-clock.h +++ b/include/dt-bindings/clock/r8a7790-clock.h @@ -21,6 +21,8 @@ #define R8A7790_CLK_SD0 7 #define R8A7790_CLK_SD1 8 #define R8A7790_CLK_Z 9 +#define R8A7790_CLK_RCAN 10 +#define R8A7790_CLK_ADSP 11 /* MSTP0 */ #define R8A7790_CLK_MSIOF0 0 @@ -80,6 +82,7 @@ /* MSTP5 */ #define R8A7790_CLK_AUDIO_DMAC1 1 #define R8A7790_CLK_AUDIO_DMAC0 2 +#define R8A7790_CLK_ADSP_MOD 6 #define R8A7790_CLK_THERMAL 22 #define R8A7790_CLK_PWM 23 diff --git a/include/dt-bindings/clock/r8a7791-clock.h b/include/dt-bindings/clock/r8a7791-clock.h index f096f3f6c16a..8fc5dc8faeea 100644 --- a/include/dt-bindings/clock/r8a7791-clock.h +++ b/include/dt-bindings/clock/r8a7791-clock.h @@ -20,6 +20,8 @@ #define R8A7791_CLK_SDH 6 #define R8A7791_CLK_SD0 7 #define R8A7791_CLK_Z 8 +#define R8A7791_CLK_RCAN 9 +#define R8A7791_CLK_ADSP 10 /* MSTP0 */ #define R8A7791_CLK_MSIOF0 0 @@ -71,6 +73,7 @@ /* MSTP5 */ #define R8A7791_CLK_AUDIO_DMAC1 1 #define R8A7791_CLK_AUDIO_DMAC0 2 +#define R8A7791_CLK_ADSP_MOD 6 #define R8A7791_CLK_THERMAL 22 #define R8A7791_CLK_PWM 23 diff --git a/include/dt-bindings/clock/sh73a0-clock.h b/include/dt-bindings/clock/sh73a0-clock.h index 1dd3eb2b7d90..53369568c24c 100644 --- a/include/dt-bindings/clock/sh73a0-clock.h +++ b/include/dt-bindings/clock/sh73a0-clock.h @@ -76,4 +76,7 @@ #define SH73A0_CLK_IIC4 10 #define SH73A0_CLK_KEYSC 3 +/* MSTP5 */ +#define SH73A0_CLK_INTCA0 8 + #endif diff --git a/include/soc/at91/at91sam9_ddrsdr.h b/include/soc/at91/at91sam9_ddrsdr.h index 0210797abf2e..dc10c52e0e91 100644 --- a/include/soc/at91/at91sam9_ddrsdr.h +++ b/include/soc/at91/at91sam9_ddrsdr.h @@ -92,7 +92,7 @@ #define AT91_DDRSDRC_UPD_MR (3 << 20) /* Update load mode register and extended mode register */ #define AT91_DDRSDRC_MDR 0x20 /* Memory Device Register */ -#define AT91_DDRSDRC_MD (3 << 0) /* Memory Device Type */ +#define AT91_DDRSDRC_MD (7 << 0) /* Memory Device Type */ #define AT91_DDRSDRC_MD_SDR 0 #define AT91_DDRSDRC_MD_LOW_POWER_SDR 1 #define AT91_DDRSDRC_MD_LOW_POWER_DDR 3 |