Merge tag 'for-linus-20140127' of git://git.infradead.org/linux-mtd

Pull MTD updates from Brian Norris:
 - Add me (Brian Norris) as an additional MTD maintainer (it'd be nice to get
   David's "ack" for this; I'm sure he approves, but he's been pretty silent
   lately)
 - Add Ezequiel Garcie as maintainer for the pxa3xx NAND driver
 - Last (?) round of pxa3xx improvements for supporting Armada 370/XP
 - Typical churn in driver boilerplate (OOM messages, printk()'s, devm_*, etc.)
 - Quad read mode support for SPI NOR driver (m25p80)
 - Update Davinci NAND driver to prepare for use on new platforms
 - Begin to kill off NAND_MAX_{PAGE,OOB}SIZE macros; more work is pending
 - Miscellaneous NAND device support (new IDs)
 - Add READ RETRY support for Micron MLC NAND
 - Support new GPMI NAND ECC layout device-tree binding
 - Avoid mapping stack/vmalloc() memory for GPMI NAND DMA

* tag 'for-linus-20140127' of git://git.infradead.org/linux-mtd: (151 commits)
  mtd: gpmi: add sanity check when mapping DMA for read_buf/write_buf
  mtd: gpmi: allocate a proper buffer for non ECC read/write
  mtd: m25p80: Set rx_nbits for Quad SPI transfers
  mtd: m25p80: Enable Quad SPI read transfers for s25fl512s
  mtd: s3c2410: Merge plat/regs-nand.h into s3c2410.c
  mtd: mtdram: add missing 'const'
  mtd: m25p80: assign default read command
  mtd: nuc900_nand: remove redundant return value check of platform_get_resource()
  mtd: plat_nand: remove redundant return value check of platform_get_resource()
  mtd: nand: add Intel manufacturer ID
  mtd: nand: add SanDisk manufacturer ID
  mtd: nand: add support for Samsung K9LCG08U0B
  mtd: nand: pxa3xx: Add support for 2048 bytes page size devices
  mtd: m25p80: Use OPCODE_QUAD_READ_4B for 4-byte addressing
  mtd: nand: don't use {read,write}_buf for 8-bit transfers
  mtd: nand: use __packed shorthand
  mtd: nand: support Micron READ RETRY
  mtd: nand: add generic READ RETRY support
  mtd: nand: add ONFI vendor block for Micron
  mtd: nand: localize ECC failures per page
  ...

1 files changed, 38 insertions, 3 deletions

diff --git a/include/linux/mtd/nand.h b/include/linux/mtd/nand.h
index 9e6c8f9f306e..32f8612469d8 100644
--- a/include/linux/mtd/nand.h
+++ b/include/linux/mtd/nand.h
@@ -219,6 +219,9 @@ struct nand_chip;
 /* ONFI feature address */
 #define ONFI_FEATURE_ADDR_TIMING_MODE	0x1
 
+/* Vendor-specific feature address (Micron) */
+#define ONFI_FEATURE_ADDR_READ_RETRY	0x89
+
 /* ONFI subfeature parameters length */
 #define ONFI_SUBFEATURE_PARAM_LEN	4
 
@@ -279,16 +282,17 @@ struct nand_onfi_params {
 	__le16 io_pin_capacitance_typ;
 	__le16 input_pin_capacitance_typ;
 	u8 input_pin_capacitance_max;
-	u8 driver_strenght_support;
+	u8 driver_strength_support;
 	__le16 t_int_r;
 	__le16 t_ald;
 	u8 reserved4[7];
 
 	/* vendor */
-	u8 reserved5[90];
+	__le16 vendor_revision;
+	u8 vendor[88];
 
 	__le16 crc;
-} __attribute__((packed));
+} __packed;
 
 #define ONFI_CRC_BASE	0x4F4E
 
@@ -326,6 +330,26 @@ struct onfi_ext_param_page {
 	 */
 } __packed;
 
+struct nand_onfi_vendor_micron {
+	u8 two_plane_read;
+	u8 read_cache;
+	u8 read_unique_id;
+	u8 dq_imped;
+	u8 dq_imped_num_settings;
+	u8 dq_imped_feat_addr;
+	u8 rb_pulldown_strength;
+	u8 rb_pulldown_strength_feat_addr;
+	u8 rb_pulldown_strength_num_settings;
+	u8 otp_mode;
+	u8 otp_page_start;
+	u8 otp_data_prot_addr;
+	u8 otp_num_pages;
+	u8 otp_feat_addr;
+	u8 read_retry_options;
+	u8 reserved[72];
+	u8 param_revision;
+} __packed;
+
 /**
  * struct nand_hw_control - Control structure for hardware controller (e.g ECC generator) shared among independent devices
  * @lock:               protection lock
@@ -432,6 +456,8 @@ struct nand_buffers {
  *			flash device.
  * @read_byte:		[REPLACEABLE] read one byte from the chip
  * @read_word:		[REPLACEABLE] read one word from the chip
+ * @write_byte:		[REPLACEABLE] write a single byte to the chip on the
+ *			low 8 I/O lines
  * @write_buf:		[REPLACEABLE] write data from the buffer to the chip
  * @read_buf:		[REPLACEABLE] read data from the chip into the buffer
  * @select_chip:	[REPLACEABLE] select chip nr
@@ -451,6 +477,8 @@ struct nand_buffers {
  *			commands to the chip.
  * @waitfunc:		[REPLACEABLE] hardwarespecific function for wait on
  *			ready.
+ * @setup_read_retry:	[FLASHSPECIFIC] flash (vendor) specific function for
+ *			setting the read-retry mode. Mostly needed for MLC NAND.
  * @ecc:		[BOARDSPECIFIC] ECC control structure
  * @buffers:		buffer structure for read/write
  * @hwcontrol:		platform-specific hardware control structure
@@ -497,6 +525,7 @@ struct nand_buffers {
  *			non 0 if ONFI supported.
  * @onfi_params:	[INTERN] holds the ONFI page parameter when ONFI is
  *			supported, 0 otherwise.
+ * @read_retries:	[INTERN] the number of read retry modes supported
  * @onfi_set_features:	[REPLACEABLE] set the features for ONFI nand
  * @onfi_get_features:	[REPLACEABLE] get the features for ONFI nand
  * @bbt:		[INTERN] bad block table pointer
@@ -521,6 +550,7 @@ struct nand_chip {
 
 	uint8_t (*read_byte)(struct mtd_info *mtd);
 	u16 (*read_word)(struct mtd_info *mtd);
+	void (*write_byte)(struct mtd_info *mtd, uint8_t byte);
 	void (*write_buf)(struct mtd_info *mtd, const uint8_t *buf, int len);
 	void (*read_buf)(struct mtd_info *mtd, uint8_t *buf, int len);
 	void (*select_chip)(struct mtd_info *mtd, int chip);
@@ -544,6 +574,7 @@ struct nand_chip {
 			int feature_addr, uint8_t *subfeature_para);
 	int (*onfi_get_features)(struct mtd_info *mtd, struct nand_chip *chip,
 			int feature_addr, uint8_t *subfeature_para);
+	int (*setup_read_retry)(struct mtd_info *mtd, int retry_mode);
 
 	int chip_delay;
 	unsigned int options;
@@ -568,6 +599,8 @@ struct nand_chip {
 	int onfi_version;
 	struct nand_onfi_params	onfi_params;
 
+	int read_retries;
+
 	flstate_t state;
 
 	uint8_t *oob_poi;
@@ -600,6 +633,8 @@ struct nand_chip {
 #define NAND_MFR_AMD		0x01
 #define NAND_MFR_MACRONIX	0xc2
 #define NAND_MFR_EON		0x92
+#define NAND_MFR_SANDISK	0x45
+#define NAND_MFR_INTEL		0x89
 
 /* The maximum expected count of bytes in the NAND ID sequence */
 #define NAND_MAX_ID_LEN 8