Add bridged amplifiers to cs42l43

Merge series from Charles Keepax <[email protected]>:

In some cs42l43 systems a couple of cs35l56 amplifiers are attached
to the cs42l43's SPI and I2S. On Windows the cs42l43 is controlled
by a SDCA class driver and these two amplifiers are controlled by
firmware running on the cs42l43. However, under Linux the decision
was made to interact with the cs42l43 directly, affording the user
greater control over the audio system. However, this has resulted
in an issue where these two bridged cs35l56 amplifiers are not
populated in ACPI and must be added manually. There is at least an
SDCA extension unit DT entry we can key off.

The process of adding this is handled using a software node, firstly the
ability to add native chip selects to software nodes must be added.
Secondly, an additional flag for naming the SPI devices is added this
allows the machine driver to key to the correct amplifier. Then finally,
the cs42l43 SPI driver adds the two amplifiers directly onto its SPI
bus.

An additional series will follow soon to add the audio machine driver
parts (in the sof-sdw driver), however that is fairly orthogonal to
this part of the process, getting the actual amplifiers registered.

1 files changed, 22 insertions, 23 deletions

diff --git a/drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c b/drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c
index 83a34e98bdc7..232b65b9c8ea 100644
--- a/drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c
+++ b/drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c
@@ -1624,8 +1624,8 @@ bool i40e_reset_all_vfs(struct i40e_pf *pf, bool flr)
 {
 	struct i40e_hw *hw = &pf->hw;
 	struct i40e_vf *vf;
-	int i, v;
 	u32 reg;
+	int i;
 
 	/* If we don't have any VFs, then there is nothing to reset */
 	if (!pf->num_alloc_vfs)
@@ -1636,11 +1636,10 @@ bool i40e_reset_all_vfs(struct i40e_pf *pf, bool flr)
 		return false;
 
 	/* Begin reset on all VFs at once */
-	for (v = 0; v < pf->num_alloc_vfs; v++) {
-		vf = &pf->vf[v];
+	for (vf = &pf->vf[0]; vf < &pf->vf[pf->num_alloc_vfs]; ++vf) {
 		/* If VF is being reset no need to trigger reset again */
 		if (!test_bit(I40E_VF_STATE_RESETTING, &vf->vf_states))
-			i40e_trigger_vf_reset(&pf->vf[v], flr);
+			i40e_trigger_vf_reset(vf, flr);
 	}
 
 	/* HW requires some time to make sure it can flush the FIFO for a VF
@@ -1649,14 +1648,13 @@ bool i40e_reset_all_vfs(struct i40e_pf *pf, bool flr)
 	 * the VFs using a simple iterator that increments once that VF has
 	 * finished resetting.
 	 */
-	for (i = 0, v = 0; i < 10 && v < pf->num_alloc_vfs; i++) {
+	for (i = 0, vf = &pf->vf[0]; i < 10 && vf < &pf->vf[pf->num_alloc_vfs]; ++i) {
 		usleep_range(10000, 20000);
 
 		/* Check each VF in sequence, beginning with the VF to fail
 		 * the previous check.
 		 */
-		while (v < pf->num_alloc_vfs) {
-			vf = &pf->vf[v];
+		while (vf < &pf->vf[pf->num_alloc_vfs]) {
 			if (!test_bit(I40E_VF_STATE_RESETTING, &vf->vf_states)) {
 				reg = rd32(hw, I40E_VPGEN_VFRSTAT(vf->vf_id));
 				if (!(reg & I40E_VPGEN_VFRSTAT_VFRD_MASK))
@@ -1666,7 +1664,7 @@ bool i40e_reset_all_vfs(struct i40e_pf *pf, bool flr)
 			/* If the current VF has finished resetting, move on
 			 * to the next VF in sequence.
 			 */
-			v++;
+			++vf;
 		}
 	}
 
@@ -1676,39 +1674,39 @@ bool i40e_reset_all_vfs(struct i40e_pf *pf, bool flr)
 	/* Display a warning if at least one VF didn't manage to reset in
 	 * time, but continue on with the operation.
 	 */
-	if (v < pf->num_alloc_vfs)
+	if (vf < &pf->vf[pf->num_alloc_vfs])
 		dev_err(&pf->pdev->dev, "VF reset check timeout on VF %d\n",
-			pf->vf[v].vf_id);
+			vf->vf_id);
 	usleep_range(10000, 20000);
 
 	/* Begin disabling all the rings associated with VFs, but do not wait
 	 * between each VF.
 	 */
-	for (v = 0; v < pf->num_alloc_vfs; v++) {
+	for (vf = &pf->vf[0]; vf < &pf->vf[pf->num_alloc_vfs]; ++vf) {
 		/* On initial reset, we don't have any queues to disable */
-		if (pf->vf[v].lan_vsi_idx == 0)
+		if (vf->lan_vsi_idx == 0)
 			continue;
 
 		/* If VF is reset in another thread just continue */
 		if (test_bit(I40E_VF_STATE_RESETTING, &vf->vf_states))
 			continue;
 
-		i40e_vsi_stop_rings_no_wait(pf->vsi[pf->vf[v].lan_vsi_idx]);
+		i40e_vsi_stop_rings_no_wait(pf->vsi[vf->lan_vsi_idx]);
 	}
 
 	/* Now that we've notified HW to disable all of the VF rings, wait
 	 * until they finish.
 	 */
-	for (v = 0; v < pf->num_alloc_vfs; v++) {
+	for (vf = &pf->vf[0]; vf < &pf->vf[pf->num_alloc_vfs]; ++vf) {
 		/* On initial reset, we don't have any queues to disable */
-		if (pf->vf[v].lan_vsi_idx == 0)
+		if (vf->lan_vsi_idx == 0)
 			continue;
 
 		/* If VF is reset in another thread just continue */
 		if (test_bit(I40E_VF_STATE_RESETTING, &vf->vf_states))
 			continue;
 
-		i40e_vsi_wait_queues_disabled(pf->vsi[pf->vf[v].lan_vsi_idx]);
+		i40e_vsi_wait_queues_disabled(pf->vsi[vf->lan_vsi_idx]);
 	}
 
 	/* Hw may need up to 50ms to finish disabling the RX queues. We
@@ -1717,12 +1715,12 @@ bool i40e_reset_all_vfs(struct i40e_pf *pf, bool flr)
 	mdelay(50);
 
 	/* Finish the reset on each VF */
-	for (v = 0; v < pf->num_alloc_vfs; v++) {
+	for (vf = &pf->vf[0]; vf < &pf->vf[pf->num_alloc_vfs]; ++vf) {
 		/* If VF is reset in another thread just continue */
 		if (test_bit(I40E_VF_STATE_RESETTING, &vf->vf_states))
 			continue;
 
-		i40e_cleanup_reset_vf(&pf->vf[v]);
+		i40e_cleanup_reset_vf(vf);
 	}
 
 	i40e_flush(hw);
@@ -3139,11 +3137,12 @@ static int i40e_vc_del_mac_addr_msg(struct i40e_vf *vf, u8 *msg)
 		/* Allow to delete VF primary MAC only if it was not set
 		 * administratively by PF or if VF is trusted.
 		 */
-		if (ether_addr_equal(addr, vf->default_lan_addr.addr) &&
-		    i40e_can_vf_change_mac(vf))
-			was_unimac_deleted = true;
-		else
-			continue;
+		if (ether_addr_equal(addr, vf->default_lan_addr.addr)) {
+			if (i40e_can_vf_change_mac(vf))
+				was_unimac_deleted = true;
+			else
+				continue;
+		}
 
 		if (i40e_del_mac_filter(vsi, al->list[i].addr)) {
 			ret = -EINVAL;