Add bridged amplifiers to cs42l43

Merge series from Charles Keepax <[email protected]>:

In some cs42l43 systems a couple of cs35l56 amplifiers are attached
to the cs42l43's SPI and I2S. On Windows the cs42l43 is controlled
by a SDCA class driver and these two amplifiers are controlled by
firmware running on the cs42l43. However, under Linux the decision
was made to interact with the cs42l43 directly, affording the user
greater control over the audio system. However, this has resulted
in an issue where these two bridged cs35l56 amplifiers are not
populated in ACPI and must be added manually. There is at least an
SDCA extension unit DT entry we can key off.

The process of adding this is handled using a software node, firstly the
ability to add native chip selects to software nodes must be added.
Secondly, an additional flag for naming the SPI devices is added this
allows the machine driver to key to the correct amplifier. Then finally,
the cs42l43 SPI driver adds the two amplifiers directly onto its SPI
bus.

An additional series will follow soon to add the audio machine driver
parts (in the sof-sdw driver), however that is fairly orthogonal to
this part of the process, getting the actual amplifiers registered.

1 files changed, 26 insertions, 12 deletions

diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.c b/drivers/net/ethernet/intel/e1000e/ich8lan.c
index 19e450a5bd31..f9e94be36e97 100644
--- a/drivers/net/ethernet/intel/e1000e/ich8lan.c
+++ b/drivers/net/ethernet/intel/e1000e/ich8lan.c
@@ -222,11 +222,18 @@ out:
 	if (hw->mac.type >= e1000_pch_lpt) {
 		/* Only unforce SMBus if ME is not active */
 		if (!(er32(FWSM) & E1000_ICH_FWSM_FW_VALID)) {
+			/* Switching PHY interface always returns MDI error
+			 * so disable retry mechanism to avoid wasting time
+			 */
+			e1000e_disable_phy_retry(hw);
+
 			/* Unforce SMBus mode in PHY */
 			e1e_rphy_locked(hw, CV_SMB_CTRL, &phy_reg);
 			phy_reg &= ~CV_SMB_CTRL_FORCE_SMBUS;
 			e1e_wphy_locked(hw, CV_SMB_CTRL, phy_reg);
 
+			e1000e_enable_phy_retry(hw);
+
 			/* Unforce SMBus mode in MAC */
 			mac_reg = er32(CTRL_EXT);
 			mac_reg &= ~E1000_CTRL_EXT_FORCE_SMBUS;
@@ -310,6 +317,11 @@ static s32 e1000_init_phy_workarounds_pchlan(struct e1000_hw *hw)
 		goto out;
 	}
 
+	/* There is no guarantee that the PHY is accessible at this time
+	 * so disable retry mechanism to avoid wasting time
+	 */
+	e1000e_disable_phy_retry(hw);
+
 	/* The MAC-PHY interconnect may be in SMBus mode.  If the PHY is
 	 * inaccessible and resetting the PHY is not blocked, toggle the
 	 * LANPHYPC Value bit to force the interconnect to PCIe mode.
@@ -380,6 +392,8 @@ static s32 e1000_init_phy_workarounds_pchlan(struct e1000_hw *hw)
 		break;
 	}
 
+	e1000e_enable_phy_retry(hw);
+
 	hw->phy.ops.release(hw);
 	if (!ret_val) {
 
@@ -449,6 +463,11 @@ static s32 e1000_init_phy_params_pchlan(struct e1000_hw *hw)
 
 	phy->id = e1000_phy_unknown;
 
+	if (hw->mac.type == e1000_pch_mtp) {
+		phy->retry_count = 2;
+		e1000e_enable_phy_retry(hw);
+	}
+
 	ret_val = e1000_init_phy_workarounds_pchlan(hw);
 	if (ret_val)
 		return ret_val;
@@ -1146,18 +1165,6 @@ s32 e1000_enable_ulp_lpt_lp(struct e1000_hw *hw, bool to_sx)
 	if (ret_val)
 		goto out;
 
-	/* Force SMBus mode in PHY */
-	ret_val = e1000_read_phy_reg_hv_locked(hw, CV_SMB_CTRL, &phy_reg);
-	if (ret_val)
-		goto release;
-	phy_reg |= CV_SMB_CTRL_FORCE_SMBUS;
-	e1000_write_phy_reg_hv_locked(hw, CV_SMB_CTRL, phy_reg);
-
-	/* Force SMBus mode in MAC */
-	mac_reg = er32(CTRL_EXT);
-	mac_reg |= E1000_CTRL_EXT_FORCE_SMBUS;
-	ew32(CTRL_EXT, mac_reg);
-
 	/* Si workaround for ULP entry flow on i127/rev6 h/w.  Enable
 	 * LPLU and disable Gig speed when entering ULP
 	 */
@@ -1313,6 +1320,11 @@ static s32 e1000_disable_ulp_lpt_lp(struct e1000_hw *hw, bool force)
 		/* Toggle LANPHYPC Value bit */
 		e1000_toggle_lanphypc_pch_lpt(hw);
 
+	/* Switching PHY interface always returns MDI error
+	 * so disable retry mechanism to avoid wasting time
+	 */
+	e1000e_disable_phy_retry(hw);
+
 	/* Unforce SMBus mode in PHY */
 	ret_val = e1000_read_phy_reg_hv_locked(hw, CV_SMB_CTRL, &phy_reg);
 	if (ret_val) {
@@ -1333,6 +1345,8 @@ static s32 e1000_disable_ulp_lpt_lp(struct e1000_hw *hw, bool force)
 	phy_reg &= ~CV_SMB_CTRL_FORCE_SMBUS;
 	e1000_write_phy_reg_hv_locked(hw, CV_SMB_CTRL, phy_reg);
 
+	e1000e_enable_phy_retry(hw);
+
 	/* Unforce SMBus mode in MAC */
 	mac_reg = er32(CTRL_EXT);
 	mac_reg &= ~E1000_CTRL_EXT_FORCE_SMBUS;