KVM: SVM: include CR3 in initial VMSA state for SEV-ES guests

Normally guests will set up CR3 themselves, but some guests, such as
kselftests, and potentially CONFIG_PVH guests, rely on being booted
with paging enabled and CR3 initialized to a pre-allocated page table.

Currently CR3 updates via KVM_SET_SREGS* are not loaded into the guest
VMCB until just prior to entering the guest. For SEV-ES/SEV-SNP, this
is too late, since it will have switched over to using the VMSA page
prior to that point, with the VMSA CR3 copied from the VMCB initial
CR3 value: 0.

Address this by sync'ing the CR3 value into the VMCB save area
immediately when KVM_SET_SREGS* is issued so it will find it's way into
the initial VMSA.

Suggested-by: Tom Lendacky <[email protected]>
Signed-off-by: Michael Roth <[email protected]>
Message-Id: <[email protected]>
[Remove vmx_post_set_cr3; add a remark about kvm_set_cr3 not calling the
 new hook. - Paolo]
Signed-off-by: Paolo Bonzini <[email protected]>

1 files changed, 19 insertions, 0 deletions

diff --git a/arch/x86/kvm/svm/svm.c b/arch/x86/kvm/svm/svm.c
index 5557867dcb69..c3d9006478a4 100644
--- a/arch/x86/kvm/svm/svm.c
+++ b/arch/x86/kvm/svm/svm.c
@@ -1801,6 +1801,24 @@ static void svm_set_gdt(struct kvm_vcpu *vcpu, struct desc_ptr *dt)
 	vmcb_mark_dirty(svm->vmcb, VMCB_DT);
 }
 
+static void svm_post_set_cr3(struct kvm_vcpu *vcpu, unsigned long cr3)
+{
+	struct vcpu_svm *svm = to_svm(vcpu);
+
+	/*
+	 * For guests that don't set guest_state_protected, the cr3 update is
+	 * handled via kvm_mmu_load() while entering the guest. For guests
+	 * that do (SEV-ES/SEV-SNP), the cr3 update needs to be written to
+	 * VMCB save area now, since the save area will become the initial
+	 * contents of the VMSA, and future VMCB save area updates won't be
+	 * seen.
+	 */
+	if (sev_es_guest(vcpu->kvm)) {
+		svm->vmcb->save.cr3 = cr3;
+		vmcb_mark_dirty(svm->vmcb, VMCB_CR);
+	}
+}
+
 void svm_set_cr0(struct kvm_vcpu *vcpu, unsigned long cr0)
 {
 	struct vcpu_svm *svm = to_svm(vcpu);
@@ -4624,6 +4642,7 @@ static struct kvm_x86_ops svm_x86_ops __initdata = {
 	.get_cpl = svm_get_cpl,
 	.get_cs_db_l_bits = kvm_get_cs_db_l_bits,
 	.set_cr0 = svm_set_cr0,
+	.post_set_cr3 = svm_post_set_cr3,
 	.is_valid_cr4 = svm_is_valid_cr4,
 	.set_cr4 = svm_set_cr4,
 	.set_efer = svm_set_efer,