blaster4385/linux-IllusionX/drivers/net, branch v6.12.1

bonding: add ns target multicast address to slave device

2024-11-14T10:16:28Z

Commit 4598380f9c54 ("bonding: fix ns validation on backup slaves") tried to resolve the issue where backup slaves couldn't be brought up when receiving IPv6 Neighbor Solicitation (NS) messages. However, this fix only worked for drivers that receive all multicast messages, such as the veth interface. For standard drivers, the NS multicast message is silently dropped because the slave device is not a member of the NS target multicast group. To address this, we need to make the slave device join the NS target multicast group, ensuring it can receive these IPv6 NS messages to validate the slave’s status properly. There are three policies before joining the multicast group: 1. All settings must be under active-backup mode (alb and tlb do not support arp_validate), with backup slaves and slaves supporting multicast. 2. We can add or remove multicast groups when arp_validate changes. 3. Other operations, such as enslaving, releasing, or setting NS targets, need to be guarded by arp_validate. Fixes: 4e24be018eb9 ("bonding: add new parameter ns_targets") Signed-off-by: Hangbin Liu Reviewed-by: Nikolay Aleksandrov Signed-off-by: Paolo Abeni

net: ti: icssg-prueth: Fix 1 PPS sync

2024-11-14T09:34:56Z

The first PPS latch time needs to be calculated by the driver (in rounded off seconds) and configured as the start time offset for the cycle. After synchronizing two PTP clocks running as master/slave, missing this would cause master and slave to start immediately with some milliseconds drift which causes the PPS signal to never synchronize with the PTP master. Fixes: 186734c15886 ("net: ti: icssg-prueth: add packet timestamping and ptp support") Signed-off-by: Meghana Malladi Reviewed-by: Vadim Fedorenko Reviewed-by: MD Danish Anwar Link: https://patch.msgid.link/20241111095842.478833-1-m-malladi@ti.com Signed-off-by: Paolo Abeni

stmmac: dwmac-intel-plat: fix call balance of tx_clk handling routines

2024-11-14T03:52:24Z

If the clock dwmac->tx_clk was not enabled in intel_eth_plat_probe, it should not be disabled in any path. Conversely, if it was enabled in intel_eth_plat_probe, it must be disabled in all error paths to ensure proper cleanup. Found by Linux Verification Center (linuxtesting.org) with Klever. Fixes: 9efc9b2b04c7 ("net: stmmac: Add dwmac-intel-plat for GBE driver") Signed-off-by: Vitalii Mordan Link: https://patch.msgid.link/20241108173334.2973603-1-mordan@ispras.ru Signed-off-by: Jakub Kicinski

net: stmmac: dwmac-mediatek: Fix inverted handling of mediatek,mac-wol

2024-11-14T03:23:02Z

The mediatek,mac-wol property is being handled backwards to what is described in the binding: it currently enables PHY WOL when the property is present and vice versa. Invert the driver logic so it matches the binding description. Fixes: fd1d62d80ebc ("net: stmmac: replace the use_phy_wol field with a flag") Signed-off-by: Nícolas F. R. A. Prado Link: https://patch.msgid.link/20241109-mediatek-mac-wol-noninverted-v2-1-0e264e213878@collabora.com Signed-off-by: Jakub Kicinski

net: phylink: ensure PHY momentary link-fails are handled

2024-11-14T02:52:54Z

Normally, phylib won't notify changes in quick succession. However, as a result of commit 3e43b903da04 ("net: phy: Immediately call adjust_link if only tx_lpi_enabled changes") this is no longer true - it is now possible that phy_link_down() and phy_link_up() will both complete before phylink's resolver has run, which means it'll miss that pl->phy_state.link momentarily became false. Rename "mac_link_dropped" to be more generic "link_failed" since it will cover more than the MAC/PCS end of the link failing, and arrange to set this in phylink_phy_change() if we notice that the PHY reports that the link is down. This will ensure that we capture an EEE reconfiguration event. Fixes: 3e43b903da04 ("net: phy: Immediately call adjust_link if only tx_lpi_enabled changes") Signed-off-by: Russell King (Oracle) Reviewed-by: Oleksij Rempel Link: https://patch.msgid.link/E1tAtcW-002RBS-LB@rmk-PC.armlinux.org.uk Signed-off-by: Jakub Kicinski

Revert "igb: Disable threaded IRQ for igb_msix_other"

2024-11-13T02:05:40Z

This reverts commit 338c4d3902feb5be49bfda530a72c7ab860e2c9f. Sebastian noticed the ISR indirectly acquires spin_locks, which are sleeping locks under PREEMPT_RT, which leads to kernel splats. Fixes: 338c4d3902feb ("igb: Disable threaded IRQ for igb_msix_other") Reported-by: Sebastian Andrzej Siewior Signed-off-by: Wander Lairson Costa Reviewed-by: Sebastian Andrzej Siewior Acked-by: Przemek Kitszel Link: https://patch.msgid.link/20241106111427.7272-1-wander@redhat.com Signed-off-by: Jakub Kicinski

net/mlx5e: Disable loopback self-test on multi-PF netdev

2024-11-12T03:23:38Z

In Multi-PF (Socket Direct) configurations, when a loopback packet is sent through one of the secondary devices, it will always be received on the primary device. This causes the loopback layer to fail in identifying the loopback packet as the devices are different. To avoid false test failures, disable the loopback self-test in Multi-PF configurations. Fixes: ed29705e4ed1 ("net/mlx5: Enable SD feature") Signed-off-by: Carolina Jubran Signed-off-by: Tariq Toukan Link: https://patch.msgid.link/20241107183527.676877-8-tariqt@nvidia.com Signed-off-by: Jakub Kicinski

net/mlx5e: CT: Fix null-ptr-deref in add rule err flow

2024-11-12T03:23:38Z

In error flow of mlx5_tc_ct_entry_add_rule(), in case ct_rule_add() callback returns error, zone_rule->attr is used uninitiated. Fix it to use attr which has the needed pointer value. Kernel log: BUG: kernel NULL pointer dereference, address: 0000000000000110 RIP: 0010:mlx5_tc_ct_entry_add_rule+0x2b1/0x2f0 [mlx5_core] … Call Trace: ? __die+0x20/0x70 ? page_fault_oops+0x150/0x3e0 ? exc_page_fault+0x74/0x140 ? asm_exc_page_fault+0x22/0x30 ? mlx5_tc_ct_entry_add_rule+0x2b1/0x2f0 [mlx5_core] ? mlx5_tc_ct_entry_add_rule+0x1d5/0x2f0 [mlx5_core] mlx5_tc_ct_block_flow_offload+0xc6a/0xf90 [mlx5_core] ? nf_flow_offload_tuple+0xd8/0x190 [nf_flow_table] nf_flow_offload_tuple+0xd8/0x190 [nf_flow_table] flow_offload_work_handler+0x142/0x320 [nf_flow_table] ? finish_task_switch.isra.0+0x15b/0x2b0 process_one_work+0x16c/0x320 worker_thread+0x28c/0x3a0 ? __pfx_worker_thread+0x10/0x10 kthread+0xb8/0xf0 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x2d/0x50 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1a/0x30 Fixes: 7fac5c2eced3 ("net/mlx5: CT: Avoid reusing modify header context for natted entries") Signed-off-by: Moshe Shemesh Reviewed-by: Cosmin Ratiu Reviewed-by: Yevgeny Kliteynik Signed-off-by: Tariq Toukan Link: https://patch.msgid.link/20241107183527.676877-7-tariqt@nvidia.com Signed-off-by: Jakub Kicinski

net/mlx5e: clear xdp features on non-uplink representors

2024-11-12T03:23:38Z

Non-uplink representor port does not support XDP. The patch clears the xdp feature by checking the net_device_ops.ndo_bpf is set or not. Verify using the netlink tool: $ tools/net/ynl/cli.py --spec Documentation/netlink/specs/netdev.yaml --dump dev-get Representor netdev before the patch: {'ifindex': 8, 'xdp-features': {'basic', 'ndo-xmit', 'ndo-xmit-sg', 'redirect', 'rx-sg', 'xsk-zerocopy'}, 'xdp-rx-metadata-features': set(), 'xdp-zc-max-segs': 1, 'xsk-features': set()}, With the patch: {'ifindex': 8, 'xdp-features': set(), 'xdp-rx-metadata-features': set(), 'xsk-features': set()}, Fixes: 4d5ab0ad964d ("net/mlx5e: take into account device reconfiguration for xdp_features flag") Signed-off-by: William Tu Signed-off-by: Tariq Toukan Link: https://patch.msgid.link/20241107183527.676877-6-tariqt@nvidia.com Signed-off-by: Jakub Kicinski

net/mlx5e: kTLS, Fix incorrect page refcounting

2024-11-12T03:23:38Z

The kTLS tx handling code is using a mix of get_page() and page_ref_inc() APIs to increment the page reference. But on the release path (mlx5e_ktls_tx_handle_resync_dump_comp()), only put_page() is used. This is an issue when using pages from large folios: the get_page() references are stored on the folio page while the page_ref_inc() references are stored directly in the given page. On release the folio page will be dereferenced too many times. This was found while doing kTLS testing with sendfile() + ZC when the served file was read from NFS on a kernel with NFS large folios support (commit 49b29a573da8 ("nfs: add support for large folios")). Fixes: 84d1bb2b139e ("net/mlx5e: kTLS, Limit DUMP wqe size") Signed-off-by: Dragos Tatulea Signed-off-by: Tariq Toukan Link: https://patch.msgid.link/20241107183527.676877-5-tariqt@nvidia.com Signed-off-by: Jakub Kicinski