blaster4385/linux-IllusionX/drivers/net/ethernet/stmicro, branch v6.12.1

stmmac: dwmac-intel-plat: fix call balance of tx_clk handling routines

2024-11-14T03:52:24Z

If the clock dwmac->tx_clk was not enabled in intel_eth_plat_probe, it should not be disabled in any path. Conversely, if it was enabled in intel_eth_plat_probe, it must be disabled in all error paths to ensure proper cleanup. Found by Linux Verification Center (linuxtesting.org) with Klever. Fixes: 9efc9b2b04c7 ("net: stmmac: Add dwmac-intel-plat for GBE driver") Signed-off-by: Vitalii Mordan Link: https://patch.msgid.link/20241108173334.2973603-1-mordan@ispras.ru Signed-off-by: Jakub Kicinski

net: stmmac: dwmac-mediatek: Fix inverted handling of mediatek,mac-wol

2024-11-14T03:23:02Z

The mediatek,mac-wol property is being handled backwards to what is described in the binding: it currently enables PHY WOL when the property is present and vice versa. Invert the driver logic so it matches the binding description. Fixes: fd1d62d80ebc ("net: stmmac: replace the use_phy_wol field with a flag") Signed-off-by: Nícolas F. R. A. Prado Link: https://patch.msgid.link/20241109-mediatek-mac-wol-noninverted-v2-1-0e264e213878@collabora.com Signed-off-by: Jakub Kicinski

net: stmmac: Fix unbalanced IRQ wake disable warning on single irq case

2024-11-07T09:04:13Z

Commit a23aa0404218 ("net: stmmac: ethtool: Fixed calltrace caused by unbalanced disable_irq_wake calls") introduced checks to prevent unbalanced enable and disable IRQ wake calls. However it only initialized the auxiliary variable on one of the paths, stmmac_request_irq_multi_msi(), missing the other, stmmac_request_irq_single(). Add the same initialization on stmmac_request_irq_single() to prevent "Unbalanced IRQ wake disable" warnings from being printed the first time disable_irq_wake() is called on platforms that run on that code path. Fixes: a23aa0404218 ("net: stmmac: ethtool: Fixed calltrace caused by unbalanced disable_irq_wake calls") Signed-off-by: Nícolas F. R. A. Prado Reviewed-by: Simon Horman Link: https://patch.msgid.link/20241101-stmmac-unbalanced-wake-single-fix-v1-1-5952524c97f0@collabora.com Signed-off-by: Paolo Abeni

net: stmmac: TSO: Fix unbalanced DMA map/unmap for non-paged SKB data

2024-10-29T10:37:10Z

In case the non-paged data of a SKB carries protocol header and protocol payload to be transmitted on a certain platform that the DMA AXI address width is configured to 40-bit/48-bit, or the size of the non-paged data is bigger than TSO_MAX_BUFF_SIZE on a certain platform that the DMA AXI address width is configured to 32-bit, then this SKB requires at least two DMA transmit descriptors to serve it. For example, three descriptors are allocated to split one DMA buffer mapped from one piece of non-paged data: dma_desc[N + 0], dma_desc[N + 1], dma_desc[N + 2]. Then three elements of tx_q->tx_skbuff_dma[] will be allocated to hold extra information to be reused in stmmac_tx_clean(): tx_q->tx_skbuff_dma[N + 0], tx_q->tx_skbuff_dma[N + 1], tx_q->tx_skbuff_dma[N + 2]. Now we focus on tx_q->tx_skbuff_dma[entry].buf, which is the DMA buffer address returned by DMA mapping call. stmmac_tx_clean() will try to unmap the DMA buffer _ONLY_IF_ tx_q->tx_skbuff_dma[entry].buf is a valid buffer address. The expected behavior that saves DMA buffer address of this non-paged data to tx_q->tx_skbuff_dma[entry].buf is: tx_q->tx_skbuff_dma[N + 0].buf = NULL; tx_q->tx_skbuff_dma[N + 1].buf = NULL; tx_q->tx_skbuff_dma[N + 2].buf = dma_map_single(); Unfortunately, the current code misbehaves like this: tx_q->tx_skbuff_dma[N + 0].buf = dma_map_single(); tx_q->tx_skbuff_dma[N + 1].buf = NULL; tx_q->tx_skbuff_dma[N + 2].buf = NULL; On the stmmac_tx_clean() side, when dma_desc[N + 0] is closed by the DMA engine, tx_q->tx_skbuff_dma[N + 0].buf is a valid buffer address obviously, then the DMA buffer will be unmapped immediately. There may be a rare case that the DMA engine does not finish the pending dma_desc[N + 1], dma_desc[N + 2] yet. Now things will go horribly wrong, DMA is going to access a unmapped/unreferenced memory region, corrupted data will be transmited or iommu fault will be triggered :( In contrast, the for-loop that maps SKB fragments behaves perfectly as expected, and that is how the driver should do for both non-paged data and paged frags actually. This patch corrects DMA map/unmap sequences by fixing the array index for tx_q->tx_skbuff_dma[entry].buf when assigning DMA buffer address. Tested and verified on DWXGMAC CORE 3.20a Reported-by: Suraj Jaiswal Fixes: f748be531d70 ("stmmac: support new GMAC4") Signed-off-by: Furong Xu <0x1207@gmail.com> Reviewed-by: Hariprasad Kelam Reviewed-by: Simon Horman Link: https://patch.msgid.link/20241021061023.2162701-1-0x1207@gmail.com Signed-off-by: Paolo Abeni

net: stmmac: dwmac4: Fix high address display by updating reg_space[] from register values

2024-10-29T10:29:40Z

The high address will display as 0 if the driver does not set the reg_space[]. To fix this, read the high address registers and update the reg_space[] accordingly. Fixes: fbf68229ffe7 ("net: stmmac: unify registers dumps methods") Signed-off-by: Ley Foon Tan Reviewed-by: Simon Horman Link: https://patch.msgid.link/20241021054625.1791965-1-leyfoon.tan@starfivetech.com Signed-off-by: Paolo Abeni

net: stmmac: dwmac-tegra: Fix link bring-up sequence

2024-10-15T10:35:17Z

The Tegra MGBE driver sometimes fails to initialize, reporting the following error, and as a result, it is unable to acquire an IP address with DHCP: tegra-mgbe 6800000.ethernet: timeout waiting for link to become ready As per the recommendation from the Tegra hardware design team, fix this issue by: - clearing the PHY_RDY bit before setting the CDR_RESET bit and then setting PHY_RDY bit before clearing CDR_RESET bit. This ensures valid data is present at UPHY RX inputs before starting the CDR lock. - adding the required delays when bringing up the UPHY lane. Note we need to use delays here because there is no alternative, such as polling, for these cases. Using the usleep_range() instead of ndelay() as sleeping is preferred over busy wait loop. Without this change we would see link failures on boot sometimes as often as 1 in 5 boots. With this fix we have not observed any failures in over 1000 boots. Fixes: d8ca113724e7 ("net: stmmac: tegra: Add MGBE support") Signed-off-by: Paritosh Dixit Link: https://patch.msgid.link/20241010142908.602712-1-paritoshd@nvidia.com Signed-off-by: Paolo Abeni

Revert "net: stmmac: set PP_FLAG_DMA_SYNC_DEV only if XDP is enabled"

2024-10-07T23:47:07Z

This reverts commit b514c47ebf41a6536551ed28a05758036e6eca7c. The commit describes that we don't have to sync the page when recycling, and it tries to optimize that case. But we do need to sync after allocation. Recycling side should be changed to pass the right sync size instead. Fixes: b514c47ebf41 ("net: stmmac: set PP_FLAG_DMA_SYNC_DEV only if XDP is enabled") Reported-by: Jon Hunter Link: https://lore.kernel.org/20241004070846.2502e9ea@kernel.org Reviewed-by: Jacob Keller Reviewed-by: Furong Xu <0x1207@gmail.com> Link: https://patch.msgid.link/20241004142115.910876-1-kuba@kernel.org Signed-off-by: Jakub Kicinski

net: stmmac: dwmac4: extend timeout for VLAN Tag register busy bit check

2024-10-01T10:35:55Z

Increase the timeout for checking the busy bit of the VLAN Tag register from 10µs to 500ms. This change is necessary to accommodate scenarios where Energy Efficient Ethernet (EEE) is enabled. Overnight testing revealed that when EEE is active, the busy bit can remain set for up to approximately 300ms. The new 500ms timeout provides a safety margin. Fixes: ed64639bc1e0 ("net: stmmac: Add support for VLAN Rx filtering") Reviewed-by: Andrew Lunn Signed-off-by: Shenwei Wang Link: https://patch.msgid.link/20240924205424.573913-1-shenwei.wang@nxp.com Signed-off-by: Paolo Abeni

net: stmmac: set PP_FLAG_DMA_SYNC_DEV only if XDP is enabled

2024-09-26T08:45:19Z

Commit 5fabb01207a2 ("net: stmmac: Add initial XDP support") sets PP_FLAG_DMA_SYNC_DEV flag for page_pool unconditionally, page_pool_recycle_direct() will call page_pool_dma_sync_for_device() on every page even the page is not going to be reused by XDP program. When XDP is not enabled, the page which holds the received buffer will be recycled once the buffer is copied into new SKB by skb_copy_to_linear_data(), then the MAC core will never reuse this page any longer. Always setting PP_FLAG_DMA_SYNC_DEV wastes CPU cycles on unnecessary calling of page_pool_dma_sync_for_device(). After this patch, up to 9% noticeable performance improvement was observed on certain platforms. Fixes: 5fabb01207a2 ("net: stmmac: Add initial XDP support") Signed-off-by: Furong Xu <0x1207@gmail.com> Link: https://patch.msgid.link/20240919121028.1348023-1-0x1207@gmail.com Signed-off-by: Paolo Abeni

net: stmmac: Fix zero-division error when disabling tc cbs

2024-09-24T09:23:33Z

The commit b8c43360f6e4 ("net: stmmac: No need to calculate speed divider when offload is disabled") allows the "port_transmit_rate_kbps" to be set to a value of 0, which is then passed to the "div_s64" function when tc-cbs is disabled. This leads to a zero-division error. When tc-cbs is disabled, the idleslope, sendslope, and credit values the credit values are not required to be configured. Therefore, adding a return statement after setting the txQ mode to DCB when tc-cbs is disabled would prevent a zero-division error. Fixes: b8c43360f6e4 ("net: stmmac: No need to calculate speed divider when offload is disabled") Cc: Co-developed-by: Choong Yong Liang Signed-off-by: Choong Yong Liang Signed-off-by: KhaiWenTan Reviewed-by: Simon Horman Link: https://patch.msgid.link/20240918061422.1589662-1-khai.wen.tan@linux.intel.com Signed-off-by: Paolo Abeni