This patch allows tail-call on the call to br_pass_frame_up
in br_handle_frame_finish. This is now possible because of the
previous patch to call br_pass_frame_up last.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the moment we deliver to the local bridge port via the function
br_pass_frame_up before all other ports. There is no requirement
for this.
For the purpose of IGMP snooping, it would be more convenient if
we did the local port last. Therefore this patch rearranges the
bridge input processing so that the local bridge port gets to see
the packet last (if at all).
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit e8469ed959c373c2ff9e6f488aa5a14971aebe1f
Author: Patrick McHardy <kaber@trash.net>
Date: Tue Feb 23 20:41:30 2010 +0100
Support specifying the initial device flags when creating a device though
rtnl_link. Devices allocated by rtnl_create_link() are marked as INITIALIZING
in order to surpress netlink registration notifications. To complete setup,
rtnl_configure_link() must be called, which performs the device flag changes
and invokes the deferred notifiers if everything went well.
Two examples:
# add macvlan to eth0
#
$ ip link add link eth0 up allmulticast on type macvlan
[LINK]11: macvlan0@eth0: <BROADCAST,MULTICAST,ALLMULTI,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN
link/ether 26:f8:84:02:f9:2a brd ff:ff:ff:ff:ff:ff
[ROUTE]ff00::/8 dev macvlan0 table local metric 256 mtu 1500 advmss 1440 hoplimit 0
[ROUTE]fe80::/64 dev macvlan0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 0
[LINK]11: macvlan0@eth0: <BROADCAST,MULTICAST,ALLMULTI,UP,LOWER_UP> mtu 1500
link/ether 26:f8:84:02:f9:2a
[ADDR]11: macvlan0 inet6 fe80::24f8:84ff:fe02:f92a/64 scope link
valid_lft forever preferred_lft forever
[ROUTE]local fe80::24f8:84ff:fe02:f92a via :: dev lo table local proto none metric 0 mtu 16436 advmss 16376 hoplimit 0
[ROUTE]default via fe80::215:e9ff:fef0:10f8 dev macvlan0 proto kernel metric 1024 mtu 1500 advmss 1440 hoplimit 0
[NEIGH]fe80::215:e9ff:fef0:10f8 dev macvlan0 lladdr 00:15:e9:f0:10:f8 router STALE
[ROUTE]2001:6f8:974::/64 dev macvlan0 proto kernel metric 256 expires 0sec mtu 1500 advmss 1440 hoplimit 0
[PREFIX]prefix 2001:6f8:974::/64 dev macvlan0 onlink autoconf valid 14400 preferred 131084
[ADDR]11: macvlan0 inet6 2001:6f8:974:0:24f8:84ff:fe02:f92a/64 scope global dynamic
valid_lft 86399sec preferred_lft 14399sec
# add VLAN to eth1, eth1 is down
#
$ ip link add link eth1 up type vlan id 1000
RTNETLINK answers: Network is down
<no events>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split dev_change_flags() into two functions: __dev_change_flags() to
perform the actual changes and __dev_notify_flags() to invoke netdevice
notifiers. This will be used by rtnl_link to defer netlink notifications
until the device has been fully configured.
This changes ordering of some operations, in particular:
- netlink notifications are sent after all changes have been performed.
As a side effect this surpresses one unnecessary netlink message when
the IFF_UP and other flags are changed simultaneously.
- The NETDEV_UP/NETDEV_DOWN and NETDEV_CHANGE notifiers are invoked
after all changes have been performed. Their relative is unchanged.
- net_dmaengine_put() is invoked before the NETDEV_DOWN notifier instead
of afterwards. This should not make any difference since both RX and TX
are already shut down at this point.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support specifying device flags during device creation,
we must be able to roll back device registration in case setting the
flags fails without sending any notifications related to the device
to userspace.
This patch changes rollback_registered_many() and register_netdevice()
to manually send netlink notifications for devices not handled by
rtnl_link and allows to defer notifications for devices handled by
rtnl_link until setup is complete.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3b8bcfd (net: introduce pre-up netdev notifier) added a new
notifier which is run before a device is set UP for use by cfg80211.
The patch missed to add the new notifier to the ignore list in
rtnetlink_event(), so we currently get an unnecessary netlink
notification before a device is set UP.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
If authentication has already been performed when the WLAN interface is
stopped, (sometimes) the ieee80211_work_purge would corrupt some
ieee80211_work-structures. The outcome is this (cleaned up):
[ 2252.398681] WARNING: at net/mac80211/work.c:995 ieee80211_work_purge
[ 2252.466430] Backtrace:
[ 2252.529266] (ieee80211_work_purge+0x0/0xcc [mac80211])
[ 2252.546875] (ieee80211_stop+0x0/0x4c0 [mac80211])
Additionally, one would get this, going on regarless of the WLAN interface
state, going on forever:
[ 2252.859985] wlan0: direct probe to 00:90:4c:60:04:00 (try -996717525)
[ 2253.055419] wlan0: direct probe to 00:90:4c:60:04:00 (try -996717524)
[ 2253.250610] wlan0: direct probe to 00:90:4c:60:04:00 (try -996717523)
[ 2253.446014] wlan0: direct probe to 00:90:4c:60:04:00 (try -996717522)
[ 2253.641357] wlan0: direct probe to 00:90:4c:60:04:00 (try -996717521)
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently if a driver does not set hw.max_listen_interval a listen
interval of 1 is negotiated with the AP. Thus, the AP could drop
buffered frames for us after just one beacon interval which can
easily happen with the current powersave and scan implementation.
To avoid this issue increase the default interval to 5 which should
be a reasonable safe default.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Quick fix for memory/module refcount leak.
Reference count of listener instance never reaches 0.
Start/stop of ulogd2 is enough to trigger this bug!
Now, refcounting there looks very fishy in particular this code:
if (!try_module_get(THIS_MODULE)) {
...
and creation of listener instance with refcount 2,
so it may very well be ripped and redone. :-)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Use list_head rather than a custom list implementation.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This reverts commit c79c5ffdce.
As Jeff points out we can't break the user visible interface
like this, we need to add this into the reserved[] thing.
Signed-off-by: David S. Miller <davem@davemloft.net>
Clients will set their MTU to 1280 if they receive a
ICMPV6_PKT_TOOBIG message with an MTU less than 1280.
To allow encapsulating of packets over a 1280 link
we should always accept packets with a size of 1280
for forwarding even if the path has a lower MTU and
fragment the encapsulated packets afterwards.
In case a forwarded packet is not going to be encapsulated
a ICMPV6_PKT_TOOBIG msg will still be send by ip6_fragment()
with the correct MTU.
Signed-off-by: Ulrich Weber <uweber@astaro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The drvinfo struct should include the number of strings that
get_rx_ntuple will return. It will be variable if an underlying
driver implements its own get_rx_ntuple routine, so userspace
needs to know how much data is coming.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use list_first_entry macro; no longer any need to use
'next' directly in list to find first entry.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch consists of a few minor cleanups to the SR-IOV
configurion code in rtnetlink.
- Remove unneccesary lock
- Remove unneccesary casts
- Return correct error code for no driver support
These changes are based on comments from Patrick McHardy
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no point of accepting an address of smaller length than dev->addr_len
here. Therefore change this for stonger check.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 4291 section 2.4 states that all uncategorized addresses
should be considered as Global Unicast.
This will remove IPV6_ADDR_RESERVED completely
and return IPV6_ADDR_UNICAST in ipv6_addr_type() instead.
Signed-off-by: Ulrich Weber <uweber@astaro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just pass in the entire repl struct. In case of a new table (e.g.
ip6t_register_table), the repldata has been previously filled with
table->name and table->size already (in ip6t_alloc_initial_table).
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
The macro is replaced by a list.h-like foreach loop. This makes
the code more inspectable.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
The macro is replaced by a list.h-like foreach loop. This makes
the code much more inspectable.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Traffic (tcp) doesnot start on a vlan interface when gro is enabled.
Even the tcp handshake was not taking place.
This is because, the eth_type_trans call before the netif_receive_skb
in napi_gro_finish() resets the skb->dev to napi->dev from the previously
set vlan netdev interface. This causes the ip_route_input to drop the
incoming packet considering it as a packet coming from a martian source.
I could repro this on 2.6.32.7 (stable) and 2.6.33-rc7.
With this fix, the traffic starts and the test runs fine on both vlan
and non-vlan interfaces.
CC: Herbert Xu <herbert@gondor.apana.org.au>
CC: Patrick McHardy <kaber@trash.net>
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we clone the SP, we should also clone the mark.
Useful for socket based SPs.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
A rule with a zero hit_count will always match.
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Cc: stable@kernel.org
Signed-off-by: Patrick McHardy <kaber@trash.net>
e->index overflows e->stamps[] every ip_pkt_list_tot packets.
Consider the case when ip_pkt_list_tot==1; the first packet received is stored
in e->stamps[0] and e->index is initialized to 1. The next received packet
timestamp is then stored at e->stamps[1] in recent_entry_update(),
a buffer overflow because the maximum e->stamps[] index is 0.
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Cc: stable@kernel.org
Signed-off-by: Patrick McHardy <kaber@trash.net>
Add ability for netlink userspace to manipulate the SPD
and manipulate the mark, retrieve it and get events with a defined
mark, etc.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ability for netlink userspace to manipulate the SAD
and manipulate the mark, retrieve it and get events with a defined
mark.
MIGRATE may be added later.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
pass mark to all SP lookups to prepare them for when we add code
to have them search.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
pass mark to all SA lookups to prepare them for when we add code
to have them search.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of custom locking that was using wait queue, lock, and atomic
to basically build a queued mutex. Use RCU for read side.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert AF_PACKET to use RCU, eliminating one more reader/writer lock.
There is no need for a real sk_del_node_init_rcu(), because sk_del_node_init
is doing the equivalent thing to hlst_del_init_rcu already; but added
some comments to try and make that obvious.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The wireless sysfs methods like the rest of the networking sysfs
methods are removed with the rtnl_lock held and block until
the existing methods stop executing. So use rtnl_trylock
and restart_syscall so that the code continues to work.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuck. It turns out that when we restart sysctls we were restarting
with the values already changed. Which unfortunately meant that
the second time through we thought there was no change and skipped
all kinds of work, despite the fact that there was indeed a change.
I have fixed this the simplest way possible by restoring the changed
values when we restart the sysctl write.
One of my coworkers spotted this bug when after disabling forwarding
on an interface pings were still forwarded.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To see the effect make sure you have an empty SPD.
On window1 "ip xfrm mon" and on window2 issue "ip xfrm policy flush"
You get prompt back in window2 and you see the flush event on window1.
With this fix, you still get prompt on window1 but no event on window2.
Thanks to Alexey Dobriyan for finding a bug in earlier version
when using pfkey to do the flushing.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
To see the effect make sure you have an empty SAD.
On window1 "ip xfrm mon" and on window2 issue "ip xfrm state flush"
You get prompt back in window2 and you see the flush event on window1.
With this fix, you still get prompt on window1 but no event on window2.
Thanks to Alexey Dobriyan for finding a bug in earlier version
when using pfkey to do the flushing.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 2367 says flushing behavior should be:
1) user space -> kernel: flush
2) kernel: flush
3) kernel -> user space: flush event to ALL listeners
This is not realistic today in the presence of selinux policies
which may reject the flush etc. So we make the sequence become:
1) user space -> kernel: flush
2) kernel: flush
3) kernel -> user space: flush response to originater from #1
4) if there were no errors then:
kernel -> user space: flush event to ALL listeners
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
The most needed command from nl80211, which Wireless Extensions had,
is support for power save mode. Add a simple command to make it possible
to enable and disable power save via nl80211.
I was also planning about extending the interface, for example adding the
timeout value, but after thinking more about this I decided not to do it.
Basically there were three reasons:
Firstly, the parameters for power save are very much hardware dependent.
Trying to find a unified interface which would work with all hardware, and
still make sense to users, will be very difficult.
Secondly, IEEE 802.11 power save implementation in Linux is still in state
of flux. We have a long way to still to go and there is no way to predict
what kind of implementation we will have after few years. And because we
need to support nl80211 interface a long time, practically forever, adding
now parameters to nl80211 might create maintenance problems later on.
Third issue are the users. Power save parameters are mostly used for
debugging, so debugfs is better, more flexible, interface for this.
For example, wpa_supplicant currently doesn't configure anything related
to power save mode. It's better to strive that kernel can automatically
optimise the power save parameters, like with help of pm qos network
and other traffic parameters.
Later on, when we have better understanding of power save, we can extend
this command with more features, if there's a need for that.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an ICMPV6_PKT_TOOBIG message is received with a MTU below 1280,
all further packets include a fragment header.
Unlike regular defragmentation, conntrack also needs to "reassemble"
those fragments in order to obtain a packet without the fragment
header for connection tracking. Currently nf_conntrack_reasm checks
whether a fragment has either IP6_MF set or an offset != 0, which
makes it ignore those fragments.
Remove the invalid check and make reassembly handle fragment queues
containing only a single fragment.
Reported-and-tested-by: Ulrich Weber <uweber@astaro.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
